Modify the helper to add a fixed delay or poll with timeout
based on platform specification to check for either Idle bit
set (DDI_BUF_CTL is idle for disable case)
v2:
* Use 2 separate functions or idle and active (Ville)
v3:
* Change the timeout to 16usecs (Ville)
v4:
* Change the timeout 8, follow spec (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701221052.8946-1-manasi.d.navare@intel.com
We have a mix of dport, intel_dport, intel_dig_port and dig_port to
reference a intel_digital_port struct. Numbers are around
5 intel_dport
36 dport
479 intel_dig_port
352 dig_port
Since we already removed the intel_ prefix from most of our other
structs, do the same here and prefer dig_port.
v2: rename everything in i915, not just a few display sources and
reword commit message (from Matt Roper)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701045054.23357-1-lucas.demarchi@intel.com
The spec requires enabling the MST Virtual Channel payload allocation
- in a separate step - after the transcoder is enabled, follow this.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200623082411.3889-1-imre.deak@intel.com
MST encoders must use the master MST transcoder's DP_TP_STATUS and
DP_TP_CONTROL registers. Atm, during the HW readout of an MST encoder
connected to a slave transcoder we reset these register addresses in
intel_dp::regs.dp_tp_* to the slave transcoder's DP_TP_* register
addresses incorrectly; fix this.
One example where the above overwite happens is the encoder HW state
validation after enabling multiple streams; see
intel_dp_mst_enc_get_config(). After that during disabling any stream
we'll get a
'Timed out waiting for ACT sent when disabling'
error, due to reading from the incorrect DP_TP_STATUS register.
This change replaces
https://patchwork.freedesktop.org/patch/369577/?series=78193&rev=1
which just papered over the problem.
v2:
- Correct the failure scenario in the commit log. (José)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616211146.23027-1-imre.deak@intel.com
For all ddi, encoder->type holds output type as ddi,
assigning it to individual o/p types is no more valid.
Fixes: 362bfb995b ("drm/i915/tgl: Add DKL PHY vswing table for HDMI")
v2: Rebase, no functional change.
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200612082237.11886-1-vandita.kulkarni@intel.com
According to BSpec the Data Island Packet should be disabled after
disabling the transcoder, but before the transcoder clock select is set
to none. On an ICL RVP, daisy-chained MST config not following this
leads to a hang with the following MCE when disabling the output:
[ 870.948739] mce: [Hardware Error]: CPU 0: Machine Check Exception: 5 Bank 6: ba00000011000402
[ 871.019212] mce: [Hardware Error]: RIP !INEXACT! 10:<ffffffff81aca652> {poll_idle+0x92/0xb0}
[ 871.019212] mce: [Hardware Error]: TSC 135a261fe61
[ 871.019212] mce: [Hardware Error]: PROCESSOR 0:706e5 TIME 1591739604 SOCKET 0 APIC 0 microcode 20
[ 871.019212] mce: [Hardware Error]: Run the above through 'mcelog --ascii'
[ 871.019212] mce: [Hardware Error]: Machine check: Processor context corrupt
[ 871.019212] Kernel panic - not syncing: Fatal machine check
[ 871.019212] Kernel Offset: disabled
Bspec: 4287
Fixes: fa37a21327 ("drm/i915: Stop sending DP SDPs on ddi disable")
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200609220616.6015-1-imre.deak@intel.com
As latest update we have now 2 voltage swing tables for DP over DKL
PHY with only one difference in Level 0 pre-emphasis 3.
So with 2 tables for DP is time to have one single function to return
all DKL voltage swing tables.
BSpec: 49292
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Khaled Almahallawy<khaled.almahallawy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200602205424.138143-1-jose.souza@intel.com
Cometlake is a small refresh of Coffeelake, but since we have found out a
difference in the plaforms, we need to identify them as separate platforms.
Since we previously took Coffeelake/Cometlake as identical, update all
IS_COFFEELAKE() to also include IS_COMETLAKE().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200602140541.5481-1-chris@chris-wilson.co.uk
In order to use a common VSC SDP Colorimetry calculating code on PSR,
it uses a new psr vsc sdp compute routine.
Because PSR routine has its own scenario and timings of writing a VSC SDP,
the current PSR routine needs to have its own drm_dp_vsc_sdp structure
member variable on struct i915_psr.
In order to calculate colorimetry information, intel_psr_update()
function and intel_psr_enable() function extend a drm_connector_state
argument.
There are no changes to PSR mechanism.
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
v4: Rebased
v8: Rebased
v10: When a PSR is enabled, it needs to add DP_SDP_VSC to
infoframes.enable.
It is needed for comparing between HW and pipe_state of VSC_SDP.
v11: If PSR is disabled by flag, it don't enable psr on pipe compute.
v12: Fix an inconsistent indenting
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-15-gwan-gyeong.mun@intel.com
Call intel_dp_set_infoframes(false) function on intel_ddi_post_disable_dp()
to make sure not to send VSC SDP and HDR Metadata Infoframe SDP.
v5: Polish commit message [Uma]
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-13-gwan-gyeong.mun@intel.com
Call intel_dp_set_infoframes() function on pipe updates to make sure
that we send VSC SDP and HDR Metadata Infoframe SDP (when applicable)
on fastsets.
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-12-gwan-gyeong.mun@intel.com
Added state readout for DP VSC SDP and enabled state validation
for DP VSC SDP.
v2: Minor style fix
v3: Replace a structure name to drm_dp_vsc_sdp from intel_dp_vsc_sdp
v4: Use struct drm_device logging macros
v10: Skip checking of VSC SDP when a crtc config has psr.
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-10-gwan-gyeong.mun@intel.com
In order to use computed config for DP SDPs (DP VSC SDP and DP HDR Metadata
Infoframe SDP), it replaces intel_dp_vsc_enable() function and
intel_dp_hdr_metadata_enable() function to intel_dp_set_infoframes()
function.
And it removes unused functions.
Before:
intel_dp_vsc_enable() and intel_dp_hdr_metadata_enable() compute sdp
configs and program sdp registers on enable callback of encoder.
After:
It separates computing of sdp configs and programming of sdp register.
The compute config callback of encoder calls computing sdp configs.
The enable callback of encoder calls programming sdp register.
v3: Rebased
v5: Polish commit message [Uma]
v10: Rebased
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514060732.3378396-8-gwan-gyeong.mun@intel.com
Get rid of several platform specific variants of
intel_digital_port_connected() and just use the ISR bits we've
stashed away.
v2: Duplicate stuff to avoid exposing platform specific
functions across files (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311155422.3043-4-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Let's get rid of the platform if ladders in
intel_digital_port_connected() and make it a vfunc. Now the if
ladders are at the encoder initialization which makes them a bit
less convoluted.
v2: Add forward decl for intel_encoder in intel_tc.h
v3: Duplicate stuff to avoid exposing platform specific
functions across files (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200311155422.3043-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Remove a number of inlines from .c files, and let the compiler decide
what's best. There's more to do, but need to start somewhere, and need
to start setting the example.
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200420140438.14672-2-jani.nikula@intel.com
Pass the encoder all the way down to
intel_ddi_transcoder_func_reg_val_get(). Allows us eliminate the
intel_ddi_get_crtc_encoder() eyesore.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417134720.16654-4-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Push the TRANS_DDI_FUNC_CTL into the encoder enable hook. The disable
is already there, and as a followup will enable us to pass the encoder
all the way down.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417134720.16654-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Since intel_ddi_enable_pipe_clock() was pushed down into the
encoder hooks we can pass on the encoder instead of having
to use intel_ddi_get_crtc_encoder().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417134720.16654-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Right now dp.regs.dp_tp_ctl/status are only set during the encoder
pre_enable() hook, what is causing all reads and writes to those
registers to go to offset 0x0 before pre_enable() is executed.
So if i915 takes the BIOS state and don't do a modeset any following
link retraing will fail.
In the case that i915 needs to do a modeset, the DDI disable sequence
will write to a wrong register not disabling DP 'Transport Enable' in
DP_TP_CTL, making a HDMI modeset in the same port/transcoder to
not light up the monitor.
So here for GENs older than 12, that have those registers fixed at
port offset range it is loading at encoder/port init while for GEN12
it will keep setting it at encoder pre_enable() and during HW state
readout.
Fixes: 4444df6e20 ("drm/i915/tgl: move DP_TP_* to transcoder")
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414230442.262092-1-jose.souza@intel.com
On TypeC ports if a sink deasserts/reasserts its HPD signal, generating
a hotplug interrupt without the sink getting unplugged/replugged from
the connector, there can be an up to 3 seconds delay until the AUX
channel gets functional. To avoid detection failures this delay causes
retry the detection for 5 seconds.
I noticed this on ICL/TGL RVPs and a DELL XPS 13 7390 ICL laptop.
References: https://gitlab.freedesktop.org/drm/intel/issues/1067
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330095425.29113-2-imre.deak@intel.com
On TypeC connectors we need to retry the detection after hotplug events
for a longer time, so add a retry counter to support this. The next
patch will add detection retries on TypeC ports needing this.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330095425.29113-1-imre.deak@intel.com
Move the final DP_TP_CTL frobbing of port sync to the master
encoder's enable hook. Now neatly out of sight from the high level
modeset code.
And thus we've eliminated all the special casing of port sync
in the high level modeset code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-14-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
We're going to want access to the atomic state for iterating
the slave crtcs when enabling the port sync master crtc. Pass
the atomic state all the way down.
The alternative would be yet another encoder hook which we'll
have to call after all the normal modeset stuff is done. Not
really a fan of yet another hook just for this.
Note that during readout state sanitation we are now going
to pass NULL as the atomic state since we don't have one.
We need to change that and then we can also s/crtc_state/crtc/
and s/conn_state/conn/ for the encoder hooks as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-13-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Transcoder port sync was introduced to the hardware in BDW. We
can trivially enable it for SKL+ since the same codepaths are
already used for ICL+ port sync. The only difference is the actual
location of the bits we need to poke.
We leave BDW out (at least for now) since it uses different modeset
paths that haven't been adapted for port sync, and IIRC using the
feature would involve some extra workarounds we've not implemented.
Pre-BDW hardware does not support port sync so we'd have to tweak
the modeset sequence to start the pipes as close together as possible
and hope for the best. So far no one has seriously tried to implement
that.
Closes: https://gitlab.freedesktop.org/drm/intel/issues/27
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-9-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
We have a bunch of code that would like to know which
CPU transcoders are actually present in the hardware. Rather than
use various ad-hoc methods let's just include a full bitmask in
the device info, alongside pipe_mask.
v2: Rebase
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200318170235.15176-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Specification was updated with vswing tables for different
configurations.
Also reordering icl_mg_phy_ddi_buf_trans struct to match table order.
BSpec: 21735
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Clinton Taylor <clinton.a.taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330210044.130510-3-jose.souza@intel.com
DDI ports have its encoders initialized with INTEL_OUTPUT_DDI type and
later eDP ports that have the type changed to INTEL_OUTPUT_EDP.
But for all other DDI ports it can drive HDMI or DP depending on what
user connects to the ports.
ehl_get_combo_buf_trans() and tgl_get_combo_buf_trans() was checking
for INTEL_OUTPUT_DP that was never true, causing wrong vswing tables
being used.
So here replacing the INTEL_OUTPUT_DP checks by the valid output types
that this functions receives as parameters. HDMI cases will be
correctly handled as it do not use encoder->type, instead it calls the
functions with INTEL_OUTPUT_HDMI as type parameter and HDMI don't have
retraining.
v2:
changed INTEL_OUTPUT_DDI to INTEL_OUTPUT_EDP and INTEL_OUTPUT_HDMI
Fixes: bd3cf6f7ce ("drm/i915/dp/tgl+: Update combo phy vswing tables")
Cc: Clinton A Taylor <clinton.a.taylor@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330210044.130510-1-jose.souza@intel.com
The DDI IO power well must not be enabled for a TypeC port in TBT mode,
ensure this during driver loading/system resume.
This gets rid of error messages like
[drm] *ERROR* power well DDI E TC2 IO state mismatch (refcount 1/enabled 0)
and avoids leaking the power ref when disabling the output.
Cc: <stable@vger.kernel.org> # v5.4+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330152244.11316-1-imre.deak@intel.com
Converting error to debug print if sink fails to configure scrambling or
TMDS bit clock ratio. In this case, we are timing out while disabling
the scrambling and setting the SCDC ratio, as there is no response
to the I2C SCDC write from the sink device. Error isn't due to something
wrong done from driver side.
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200302213807.6488-1-swati2.sharma@intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
intel_ddi_clock_get() tests the DPLL ID against DPLL_ID_ICL_TBTPLL (2)
to determine whether to try to descend into a TBT-specific handler.
However this test will also be true when DPLL4 on EHL is used since that
shares the same DPLL ID (2).
Add an extra check to ensure the PHY is actually a Type-C PHY before
descending into the TBT handling. This should ensure EHL still takes
the correct code path and somewhat future-proof the code as well.
v2: Drop the gen+ check since only gen11+ platforms can have Type-C
outputs. (Imre)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1369
Fixes: 45e4728b87 ("drm/i915: Move DPLL frequency calculation to intel_dpll_mgr.c")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200303195043.959913-1-matthew.d.roper@intel.com
Move all the DPLL params->DPLL frequency conversion functions to
intel_dpll_mgr.c where the corresponding inverse conversions are.
The GEN11+ TBT PLL outputs multiple frequencies and for selecting the
one in use we need to check the DDI CLK mux. As part of the DDI clock
logic this selection is kept in intel_ddi.c.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226203455.23032-7-imre.deak@intel.com
For clarity add a new DPLL specific struct to the i915 device struct and
move all DPLL fields into it. Accordingly remove the dpll_ prefixes, as
the new struct already provides the required namespacing.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226203455.23032-4-imre.deak@intel.com
This patch pushes out the computation of master and slave
transcoders in crtc states after encoder's compute_config hook.
This ensures that the assigned master slave crtcs have exact same
mode and timings which is a requirement for Port sync mode
to be enabled.
v3:
* Make crtc_state const, remove crtc state NULL init (Ville)
v2:
* Correct indentation
* Rename to intel_ddi_port_sync_transcoders (Ville)
* remove unwanted debug (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200214114126.13192-2-manasi.d.navare@intel.com
Commit 1c9d2eb241 ("drm/i915: move intel_dp_set_m_n() to encoder for
DDI platforms") moved the intel_dp_set_m_n() from hsw_crtc_enable()
to intel_ddi_pre_enable_dp() but it missed add it to
intel_mst_pre_enable_dp() causing MST slaves to not work.
v2: Not setting intel_ddi_set_dp_msa() twice for MST master
Fixes: 1c9d2eb241 ("drm/i915: move intel_dp_set_m_n() to encoder for DDI platforms")
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200211185008.30806-1-jose.souza@intel.com
A recent bspec update added an extra voltage level that we didn't have
on ICL and new criteria for selecting the level.
Bspec: 49208
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200207001417.1229251-2-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Voltage level depends not only on the cdclk, but also on the DDI clock.
Last time the bspec voltage level table for EHL was updated, we only
updated the cdclk requirements, but forgot to account for the new port
clock criteria.
Bspec: 21809
Fixes: d147483884 ("drm/i915/ehl: Update voltage level checks")
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200207001417.1229251-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
TGL is suffering of timeouts and fifo underruns when disabling
transcoder in MST mode, this is fixed by set TRANS_DDI_MODE_SELECT to
0(HDMI mode) when clearing DDI select.
Although BSpec disable sequence don't require this step, it is a
harmless change and it is also done by Windows driver.
Anyhow HW team was notified about that but it can take some time to
documentation to be updated.
A case that always lead to those issues is:
- do a modeset enabling pipe A and pipe B in the same MST stream
leaving A as master
- disable pipe A, promote B as master doing a full modeset in A
- enable pipe A, changing the master transcoder back to A(doing a
full modeset in B)
- Pow: underruns and timeouts
The transcoders involved will only work again when complete disabled
and their power wells turned off causing a reset in their registers.
v2: Setting TRANS_DDI_MODE_SELECT to default when clearing DDI select
not anymore when disabling TRANS_DDI, both work but this one looks
more safe. (Ville comment)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200203225549.152301-1-jose.souza@intel.com
The DDI encoder code shouln't have to know about the guts of
HDCP. Abstract the pipe update code to a new intel_hdcp_update_pipe() in
intel_hdcp.c. No functional changes.
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128163803.5954-1-jani.nikula@intel.com
To allow better flexibility for encoder specific code, push
intel_enable_pipe(), lpt_pch_enable() and intel_crtc_vblank_on() down to
the encoders from hsw_crtc_enable().
There's slight duplication, but also more clarity with the reduced
conditional statements.
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128162850.8660-1-jani.nikula@intel.com
A recent change in BSpec allow us to change EXTLINE while transcoder
is enabled so this allow us to change it even when doing the first
fastset after taking over previous hardware state set by BIOS.
BIOS don't enable PSR, so if sink supports PSR it will be enabled on
the first fastset, so moving the EXTLINE compute and set to PSR flows
allow us to simplfy a bunch of code.
This will save a lot of time in all the IGT tests that uses CRC, as
when PSR2 is enabled CRCs are not generated, so we switch to PSR1, so
the previous code would compute dc3co_exitline=0 causing a full
modeset that would shutdown pipe, enable and train link.
v2: only programming EXTLINE when DC3CO is enabled
BSpec: 49196
Cc: Imre Deak <imre.deak@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200122182617.18597-2-jose.souza@intel.com
TGL has now a table for RBR and HBR and another table for HBR2 over
combo phys. The HBR2 one has some small changes comparing to the ICL
one, so adding two new tables and adding a function to return TGL
combo phy tables.
v2:
- reordered the tgl_combo_phy_ddi_translations_dp_hbr2 to reduce diff
(Matt)
- removed definition of rates, kept using raw number(Jani and Ville)
- changed code to use icl_get_combo_buf_trans() for non-DP as those
are equal between TGL and ICL(Matt)
BSpec: 49291
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200110233902.154960-1-jose.souza@intel.com
When moving the pipe disable & co. function calls from
haswell_crtc_disable() into the encoder .post_disable() hooks I
neglected to account for the MST vs. DDI interactions properly.
This now leads us to call these functions two times for the last
MST stream (once from the MST code and a second time from the DDI
code). The calls from the DDI code should only be done for SST
and not MST. Add the proper check for that.
This results in an MCE on ICL. My vague theory is that we turn off
the transcoder clock from the MST code and then we proceed to touch
something in the DDI code which still depends on that clock causing
the hardware to become upset. Though I can't really explain why
Stan's hack of omitting the pipe disable in the MST code would avoid
the MCE since we should still be turning off the transcoder clock.
But maybe there's something magic in the hw that keeps the clock on
as long as the pipe is on. Or maybe the clock isn't the problem and
we now touch something in the DDI disable code that really does need
the pipe to be still enabled.
v2: Rebase to latest drm-tip
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reported-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/issues/901
Fixes: 773b4b5435 ("drm/i915: Move stuff from haswell_crtc_disable() into encoder .post_disable()")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200108144550.29280-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Talked with HW team and this is a left over, driver should not
program clockgating, mg or dekel firmware is reponsible for any
clockgating programing.
Also removing the register and bits definition related to clockgating.
v2:
Added WARN_ON
v3:
Only calling icl_phy_set_clock_gating() on intel_ddi_pre_enable_hdmi
for GEN11
v4:
ICL should also not program clockgating (thanks Matt for catching
this)
BSpec issue: 20885
BSpec: 49292
BSpec: 21735
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200107170922.153612-1-jose.souza@intel.com
While clearing the Ports ync mode enable and master select bits
we need to clear the register completely instead of using disable masks
v3:
* Remove reg variable (Matt)
v2:
* Just write 0 to the reg (Ville)
* Rebase
Bugzilla: https://gitlab.freedesktop.org/drm/intel/issues/5
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Fixes: 51528afe7c ("drm/i915/display/icl: Disable transcoder port sync as part of crtc_disable() sequence")
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191228031204.10189-3-manasi.d.navare@intel.com
We are currently using a mix of platform name and acronym to name the
functions. Let's prefer the acronym as it should be clear what platform
it's about and it's shorter, so it doesn't go over 80 columns in a few
cases. This converts ironlake to ilk where appropriate.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224084012.24241-7-lucas.demarchi@intel.com
We are currently using a mix of platform name and acronym to name the
functions. Let's prefer the acronym as it should be clear what platform
it's about and it's shorter, so it doesn't go over 80 columns in a few
cases. This converts skylake to skl where appropriate.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224084012.24241-4-lucas.demarchi@intel.com
We are currently using a mix of platform name and acronym to name the
functions. Let's prefer the acronym as it should be clear what platform
it's about and it's shorter, so it doesn't go over 80 columns in a few
cases. This converts haswell to hsw where appropriate.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191224084012.24241-3-lucas.demarchi@intel.com
The disable sequence after wait for transcoder off was not correctly
implemented.
The MST disable sequence is basically the same for HSW, SKL, ICL and
TGL, with just minor changes for TGL.
With this last patch we finally fixed the hotplugs triggered by MST
sinks during the disable/enable sequence, those were causing source
to try to do a link training while it was not ready causing CPU pipe
FIFO underrrus on TGL.
v2: Only unsetting TGL_TRANS_DDI_PORT_MASK for TGL on the post
disable sequence
v4: Rebased, moved MST sequences to intel_mst_post_disable_dp()
BSpec: 4231
BSpec: 4163
BSpec: 22243
BSpec: 49190
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191223010654.67037-4-jose.souza@intel.com
On TGL the blending of all the streams have moved from DDI to
transcoder, so now every transcoder working over the same MST port must
send its stream to a master transcoder and master will send to DDI
respecting the time slots.
So here adding all the CRTCs that shares the same MST stream if
needed and computing their state again, it will pick the lowest
pipe/transcoder among the ones in the same stream to be master.
Most of the time skl_commit_modeset_enables() enables pipes in a
crescent order but due DDB overlapping it might not happen, this
scenarios will be handled in the next patch.
v2:
- Using recently added intel_crtc_state_reset() to set
mst_master_transcoder to invalid transcoder for all non gen12 & MST
code paths
- Setting lowest pipe/transcoder as master, previously it was the
first one but setting a predictable one will help in future MST e
port sync integration
- Moving to intel type as much as we can
v3:
- Now intel_dp_mst_master_trans_compute() returns the MST master transcoder
- Replaced stdbool.h by linux/types.h
- Skip the connector being checked in
intel_dp_mst_atomic_master_trans_check()
- Using pipe instead of transcoder to compute MST master
v4:
- renamed connector_state to conn_state
v5:
- Improved the parameters of intel_dp_mst_master_trans_compute() to
simply code
- Added call drm_atomic_add_affected_planes() in
intel_dp_mst_atomic_master_trans_check() as helper could not do it
for us
- Removed "if (ret)" left over from v3 changes
v6:
- handled ret == I915_MAX_PIPES case in compute
BSpec: 50493
BSpec: 49190
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191223010654.67037-2-jose.souza@intel.com
Move all of haswell_crtc_disable() into the encoder
.post_disable() hooks. Now we're left with just
calling the .disable() and .post_disable() hooks
back to back.
I chose to move the code into the .post_disable() hook instead
of the .disable() hook as most of the sequence is currently
implemented in the .post_disable() hook.
We should collapse it all down to just one hook and then the
encoders can drive the modeset sequence fully. But that may
need some further refactoring as we currently call the
ddi .post_disable() hook from mst code and we can't just
replace that with a call to the ddi .disable() hook.
Should also follow up with similar treatment for the enable
sequence but let's start here where it's easier.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213195217.15168-5-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
HSW+ platforms call encoder .post_disable() and .post_pll_disable()
back to back. And since we don't even disable the PLL in between
let's just move everything into .post_disable().
intel_dp_mst does forward the .post_disable() call to intel_ddi at
the very end of its own .post_disable() hook, so this time MST
I shouldn't even break MST by accident.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213195217.15168-2-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Remove the pointless vfunc detour for hsw_fdi_link_train()
and just call it directly. Also pass the encoder in so we
can nuke the silly encoder loop within.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213195217.15168-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Add basic hardware state readout for DSC, and check the most relevant
details in the state checker.
v2:
- check for DSC power before reading its state
- check if source supports DSC at all
As a side effect, this should also get the power domains for the enabled
DSC on takeover, and subsequently disable DSC if it's not needed.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3fb018cf9bd9a4c275aab389b6ec0f2a4e938bb9.1575974743.git.jani.nikula@intel.com
intel_hdcp_transcoder_config() is clobbering some globally visible
state in .compute_config(). That is a big no no as .compute_config()
is supposed to have no visible side effects when either the commit
fails or it's just a TEST_ONLY commit.
Inline this stuff into intel_hdcp_enable() so that the state only
gets modified when we actually commit the state to the hardware.
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Fixes: 39e2df090c ("drm/i915/hdcp: update current transcoder into intel_hdcp")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191204180549.1267-2-ville.syrjala@linux.intel.com
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
For TGL the step to turn off the transcoder clock was moved to after
the complete shutdown of DDI. Only the MST slave transcoders should
disable the clock before that.
v2:
- Adding last_mst_stream to intel_mst_post_disable_dp, make code more
easy to read and is similar to first_mst_stream in
intel_mst_pre_enable_dp()(Ville's idea)
- Calling intel_ddi_disable_pipe_clock() for GEN12+ right
intel_disable_ddi_buf() as stated in BSpec(Ville)
BSpec: 49190
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191205210350.96795-2-jose.souza@intel.com
Disabling pipe/transcoder clock before power down sink could cause
sink lost signal, causing it to trigger a hotplug to notify source
that link signal was lost.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191202222513.337777-2-jose.souza@intel.com
The bspec initially provided a single DKL PHY vswing table for both HDMI
and DP, but was recently updated to include an independent table for
HDMI.
Bspec: 49292
Fixes: 978c3e539b ("drm/i915/tgl: Add dkl phy programming sequences")
Cc: Clinton A Taylor <clinton.a.taylor@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118180219.9309-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
This register was being enabled after enable TRANS_DDI_FUNC_CTL and
PIPECONF/TRANS_CONF while BSpec states that it should be set when
enabling TRANS_DDI_FUNC_CTL.
BSpec: 49190
BSpec: 22243
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191107214559.77087-3-jose.souza@intel.com
The setting of MSA is done by the DDI .pre_enable() hook. And when we are
using MST, the MSA is only set to first mst stream by calling of
DDI .pre_eanble() hook. It raies issues to non-first mst streams.
Wrong MSA or missed MSA packets might show scrambled screen or wrong
screen.
This splits a setting of MSA to MST and SST cases. And In the MST case it
will call a setting of MSA after an allocating of Virtual Channel from
MST encoder pre_enable callback.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112212
Fixes: 0c06fa1560 ("drm/i915/dp: Add support of BT.2020 Colorimetry to DP MSA")
Fixes: d4a415dcda ("drm/i915: Fix MST oops due to MSA changes")
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191106212636.502471-1-gwan-gyeong.mun@intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
[vsyrjala: nuke spurious newline]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Rather than just specifying the bullet numbers from the bspec (e.g.,
"4.b") actually include the description of what the bspec wants us to
do. Steps can be renumbered or moved so including the description will
help us match the code up to the spec. Plus if we add support for new
platforms, some of the steps may be added/removed so more descriptive
comments will be useful for ensuring all of the bspec requirements are
met.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191107174527.11165-1-matthew.d.roper@intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Prefer using intel_encoder and pass the base where needed rather than
keeping both encoder and intel_encoder variables around.
v2: actually add all changes to the patch
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191106071715.10613-1-lucas.demarchi@intel.com
For MST on Tiger Lake there are different moments when we need to
configure the transcoder clock select. For the first link this is in step
7.a of the spec, before training the link. For additional streams this
should be done as part of step 8.b after programming receiver VC Payload
ID.
Bspec: 49190
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191030012448.14937-4-lucas.demarchi@intel.com
Split up crtc_state->base to uapi. This is done using the following patch,
ran after the previous commit that splits out any hw references:
@@
struct intel_crtc_state *T;
@@
-T->base
+T->uapi
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-5-maarten.lankhorst@linux.intel.com
Split up crtc_state->base to hw where appropriate. This is done using the following patch:
@@
struct intel_crtc_state *T;
identifier x =~ "^(active|enable|degamma_lut|gamma_lut|ctm|mode|adjusted_mode)$";
@@
-T->base.x
+T->hw.x
@@
struct drm_crtc_state *T;
identifier x =~ "^(active|enable|degamma_lut|gamma_lut|ctm|mode|adjusted_mode)$";
@@
-to_intel_crtc_state(T)->base.x
+to_intel_crtc_state(T)->hw.x
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-4-maarten.lankhorst@linux.intel.com
