All callers are prepared for alloc failures anyway, so this error
can safely be boomeranged to the callers domain without super
bad consequences. ...At worst the connection might go into a state
where each RTO tries to (unsuccessfully) re-fragment with such
a mis-sized value and eventually dies.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
auth_hmacs field of struct sctp_cookie is used for store
Requested HMAC Algorithm Parameter, and each HMAC Identifier
is 2 bytes, so the length should be:
SCTP_AUTH_NUM_HMACS * sizeof(__u16) + 2
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_ethtool_get_rx_csum() won't report rx checksumming when it's not
changeable and driver is converted to hw_features and friends. Fix this.
(dev->hw_features & NETIF_F_RXCSUM) check is dropped - if the
ethtool_ops->get_rx_csum is set, then driver is not coverted, yet.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documentation for the USB ethernet devices suggests that
only some devices are supposed to use usb0 as the network interface
name instead of eth0. The logic used there, and documented in
Kconfig for CDC is that eth0 will be used when the mac address
is a globally assigned one, but usb0 is used for the locally
managed range that is typically used on point-to-point links.
Unfortunately, this has caused a lot of pain on the smsc95xx
device that is used on the popular pandaboard without an
EEPROM to store the MAC address, which causes the driver to
call random_ether_address().
Obviously, there should be a proper MAC addressed assigned to
the device, and discussions are ongoing about how to solve
this, but this patch at least makes sure that the default
interface naming gets a little saner and matches what the
user can expect based on the documentation, including for
new devices.
The approach taken here is to flag whether a device might be a
point-to-point link with the new FLAG_POINTTOPOINT setting in
the usbnet driver_info. A driver can set both FLAG_POINTTOPOINT
and FLAG_ETHER if it is not sure (e.g. cdc_ether), or just one
of the two. The usbnet framework only looks at the MAC address
for device naming if both flags are set, otherwise it trusts the
flag.
Signed-off-by: Arnd Bergmann <arnd.bergmann@linaro.org>
Tested-by: Andy Green <andy.green@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we have CONFIG_ARCH_DMA_ADDR_T_64BIT. We can fix the hacky
dma_addr_t size test cleanly.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 60d9f461a2 ("appletalk: remove
the BKL") added a dereference of "sk" before checking for NULL in
atalk_release().
Guard the code block completely, rather than partially, with the
NULL check.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After we made debugobjects working again, we got the following:
WARNING: at lib/debugobjects.c:262 debug_print_object+0x8e/0xb0()
Hardware name: System Product Name
ODEBUG: free active (active state 0) object type: timer_list hint: hci_cmd_timer+0x0/0x60
Pid: 2125, comm: dmsetup Tainted: G W 2.6.38-06707-gc62b389 #110375
Call Trace:
[<ffffffff8104700a>] warn_slowpath_common+0x7a/0xb0
[<ffffffff810470b6>] warn_slowpath_fmt+0x46/0x50
[<ffffffff812d3a5e>] debug_print_object+0x8e/0xb0
[<ffffffff81bd8810>] ? hci_cmd_timer+0x0/0x60
[<ffffffff812d4685>] debug_check_no_obj_freed+0x125/0x230
[<ffffffff810f1063>] ? check_object+0xb3/0x2b0
[<ffffffff810f3630>] kfree+0x150/0x190
[<ffffffff81be4d06>] ? bt_host_release+0x16/0x20
[<ffffffff81be4d06>] bt_host_release+0x16/0x20
[<ffffffff813a1907>] device_release+0x27/0xa0
[<ffffffff812c519c>] kobject_release+0x4c/0xa0
[<ffffffff812c5150>] ? kobject_release+0x0/0xa0
[<ffffffff812c61f6>] kref_put+0x36/0x70
[<ffffffff812c4d37>] kobject_put+0x27/0x60
[<ffffffff813a21f7>] put_device+0x17/0x20
[<ffffffff81bda4f9>] hci_free_dev+0x29/0x30
[<ffffffff81928be6>] vhci_release+0x36/0x70
[<ffffffff810fb366>] fput+0xd6/0x1f0
[<ffffffff810f8fe6>] filp_close+0x66/0x90
[<ffffffff810f90a9>] sys_close+0x99/0xf0
[<ffffffff81d4c96b>] system_call_fastpath+0x16/0x1b
That timer was introduced with commit 6bd32326cda(Bluetooth: Use
proper timer for hci command timout)
Timer seems to be running when the thing is closed. Removing the timer
unconditionally fixes the problem. And yes, it needs to be fixed
before the HCI_UP check.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Sometimes L2CAP connection remains hanging. Make sure that
L2CAP channel is deleted.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The code was correctly calling _unlock at the end of the function but
there was no actual _lock call anywhere.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Now that we have support for LE connections, before discarding a
frame we must check if there's a LE connection over that transport.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Acked-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We can't send new commands before a cmd_complete for the HCI_RESET command
shows up.
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Reported-by: Justin P. Mattock <justinmattock@gmail.com>
Reported-by: Ed Tomlinson <edt@aei.ca>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Tested-by: Justin P. Mattock <justinmattock@gmail.com>
Tested-by: Mikko Vinni <mmvinni@yahoo.com>
Tested-by: Ed Tomlinson <edt@aei.ca>
This patch lets 'l2cap_pinfo.unacked_frames' be incremented only
the first time a frame is transmitted.
Previously it was being incremented for retransmitted packets
too resulting the value to cross the transmit window size.
Signed-off-by: Suraj Sumangala <suraj@atheros.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Just adding the vendor details makes it work fine.
Signed-off-by: Marc-Antoine Perennou <Marc-Antoine@Perennou.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds automated creation of the local EIR data based on what
16-bit UUIDs are registered and what the device name is. This should
cover the majority use cases, however things like 32/128-bit UUIDs, TX
power and Device ID will need to be added later to be on par with what
bluetoothd is capable of doing (without the Management interface).
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Information requests/responses are unbound to L2CAP channel. Patch
fixes issue arising when two devices connects at the same time to
each other. This way we do not process out of the context messages.
We are safe dropping info_rsp since info_timer is left running.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
bt_accept_enqueue() is not really a channel action, so do it outside.
This patch is part of a set of patches to create an struct l2cap_chan to
have a clear separation between the struct sock and the L2CAP channel
stuff.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
If remote side reports oob availability or we are pairing initiator
use oob data for pairing if available.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds commands to add and remove remote OOB data to the managment
interface. Remote data is stored in kernel and can be used by corresponding
HCI commands and events when needed.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a command to read local OOB data to the managment interface.
The command maps directly to the Read Local OOB Data HCI command.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Since index is in mgmt_hdr it is possible to have mgmt command with
no parameters that still needs to add itself to pending list.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This field holds not whole command but only command specific
parameters.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
As warned by checkpatch.pl, use #include <linux/uaccess.h> instead of
<asm/uaccess.h>
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
As warned by checkpatch.pl, use #include <linux/uaccess.h> instead of
<asm/uaccess.h>
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
BNEP_RX_TYPES and INCA macros have only one user each and don't provide
any benefits compared to opencoding them.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a new set_local_name management command as well as a
local_name_changed management event. With these user space can both
change the local name as well as monitor changes to it by others.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds the name of the adapter to the reply of the read_info
management command.
The management messages reserve 249 bytes for the name instead of 248
(like in the HCI spec) so that there is always a guarantee that it is
nul-terminated. That way it can safely be passed onto string
manipulation functions.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a clear define for the maximum device name length in HCI
messages and thereby avoids magic numbers in the code.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We should reduce the number of reserved completion queues from the total
number of entries. Since the queue size is power of two, not reducing the
reserved entries, caused a double queue size, which may lead to allocation
failures in some cases.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of allocation failure, tried to use the promiscuous QP
entry that was previously freed.
Now freeing this entry only in case we will not put it back to the list
of promiscuous entries.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like DCCP and other similar pieces of code, there are mechanisms
here to try allocating smaller hash tables if the allocation
fails. So pass in __GFP_NOWARN like the others do instead of
emitting a scary message.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commits 01a16b21 (netlink: kill eff_cap from struct netlink_skb_parms)
and c53fa1ed (netlink: kill loginuid/sessionid/sid members from struct
netlink_skb_parms) removed some members from struct netlink_skb_parms
that depend on the current context, all netlink users are now required
to do synchronous message processing.
connector however queues received messages and processes them in a work
queue, which is not valid anymore. This patch converts connector to do
synchronous message processing by invoking the registered callback handler
directly from the netlink receive function.
In order to avoid invoking the callback with connector locks held, a
reference count is added to struct cn_callback_entry, the reference
is taken when finding a matching callback entry on the device's queue_list
and released after the callback handler has been invoked.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel J Blueman reported a lockdep splat in trie_firstleaf(), caused by
RTNL being not locked before a call to fib_table_flush()
Reported-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't flap VCs when carrier state changes; higher-level protocols
can detect loss of connectivity and act accordingly. This is more
consistent with how other network interfaces work.
We no longer use release_vccs() so we can delete it.
release_vccs() was duplicated from net/atm/common.c; make the
corresponding function exported, since other code duplicates it
and could leverage it if it were public.
Signed-off-by: Philip A. Prindeville <philipp@redfish-solutions.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Omit pkt_hdr preamble when dumping transmitted packet as hex-dump;
we can pull this up because the frame has already been sent, and
dumping it is the last thing we do with it before freeing it.
Also include the size, vpi, and vci in the debug as is done on
receive.
Use "port" consistently instead of "device" intermittently.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use VPI.VCI notation consistently throughout the module. This is the
one remaining place where the VCI is used before the VPI in any output.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has the same purpose (and value) as ah->config.max_txtrig_level
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to the number of tx queue, the number of keycache entries depends
on the chip and shouldn't be messed with based on EEPROM data.
Remove this field and stick to using AR_KEYTABLE_SIZE
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
