The conversion to video_ioctl2 is the first phase to converting this driver
to the latest v4l2 framework.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by David Engel <david@istwok.net>, ATSC115 doesn't work
fine with mythtv. This software opens both analog and dvb interfaces of
saa7134.
What happens is that some tuner commands are going to the wrong place,
as shown at the logs:
Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: using tuner params #0 (ntsc)
Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: freq = 67.25 (1076), range = 0, config = 0xce, cb = 0x01
Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: Freq= 67.25 MHz, V_IF=45.75 MHz, Offset=0.00 MHz, div=1808
Feb 12 20:37:48 opus kernel: tuner 1-0061: tv freq set to 67.25
Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: using tuner params #0 (ntsc)
Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: freq = 67.25 (1076), range = 0, config = 0xce, cb = 0x01
Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: Freq= 67.25 MHz, V_IF=45.75 MHz, Offset=0.00 MHz, div=1808
Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: tv 0x07 0x10 0xce 0x01
Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: tv 0x07 0x10 0xce 0x01
This happens due to a hack at TUV1236D analog setup, where it replaces
tuner address, at 0x61 for 0x0a, in order to save a few memory bytes.
The code assumes that nobody else would try to access the tuner during
that setup, but the point is that there's no lock to protect such
access. So, this opens the possibility of race conditions to happen.
Instead of hacking tuner address, this patch uses a temporary var with
the proper tuner value to be used during the setup. This should save
the issue, although we should consider to write some analog/digital
lock at saa7134 driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The default case of the switch didn't unlock the mutex.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't call tda8290_init_tuner unless we have either a TDA8275 or TDA8275A
present. Calling this function will cause a TDA18271 to get sick, so we
should only call it when needed.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
/home/v4l/master/v4l/tda8290.c:233:7: warning: symbol 'i' shadows an earlier one
/home/v4l/master/v4l/tda8290.c:178:3: warning: symbol 'fm_mode' was not declared. Should it be static?
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since internal to v4l2 the ioctl prototype is the same regardless of it
being called through .ioctl or .unlocked_ioctl, we need to convert it all
to the long return type of unlocked_ioctl.
Thanks to Jean-Francois Moine for posting an initial patch for this and
thus bringing it to our attention.
Cc: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Introduce a struct v4l2_file_operations for v4l2 drivers.
Remove the unnecessary inode argument.
Move compat32 handling (and llseek) into the v4l2-dev core: this is now
handled in the v4l2 core and no longer in the drivers themselves.
Note that this changeset reverts an earlier patch that changed the return
type of__video_ioctl2 from int to long. This change will be reinstated
later in a much improved version.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The init_fw option was broken for the HVR-950q because we would call the reset
callback inside of dvb_attach() and the callback had not been setup yet.
Michael Krufky (who added the init_fw feature) says it's no longer required,
so just remove the option completely.
Thanks to user Zzeiss from #linuxtv chat for reporting the issue and
Michael Krufky <mkrufky@linuxtv.org> for proposing the fix.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tuner-xc3028 can be put to sleep to save power. However, if not properly
recovered from sleep, the device won't work. It is noticed that some
devices doesn't recover properly, so let's add a dump_stack() as a debug
option, to allow us to track when this happens.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tda8290 were using some random video standard for FM. This results on random
errors. Instead, program tda8290 in expert mode, using a configuration near the
one specified on NXP datasheet for tda8295 (available on their site).
Also, properly display that the device is on radio mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Probably due to a removed code, tda827x were doing some wrong calculus at the
returned frequency. I suspect that the original idea were to return the
programmed divisor converted into frequency again.
However, the current code is sometimes multiplying the programmed frequency by
62500, and, on other cases, like radio, it dividing it by 1000.
Instead of doing such math, let's just store the frequency value as requested by
the caller module.
Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) for sponsoring
this
development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
/home/mauro/v4l-dvb/v4l/tuner-xc2028.c: In function 'xc2028_sleep':
/home/mauro/v4l-dvb/v4l/tuner-xc2028.c:1111: warning: 'return' with no value, in function returning non-void
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the firmware load is now fast on most boards, better to keep the tuner
off by default. A modprobe parameter were added to keep the old behavior,
to be used by old devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ARRAY_SIZE is more concise to use when the size of an array is divided by
the size of its type or the size of its first element.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@i@
@@
@depends on i using "paren.iso"@
type T;
T[] E;
@@
- (sizeof(E)/sizeof(E[...]))
+ ARRAY_SIZE(E)
@depends on i using "paren.iso"@
type T;
T[] E;
@@
- (sizeof(E)/sizeof(T))
+ ARRAY_SIZE(E)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the ATI TV Wonder HD 600 USB Remote Control
(required a new keymap)
[mchehab@redhat.com: Fix CodingStyle]
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The inode argument was never used. Removing it from video_usercopy
brings the function pointer type of video_usercopy in line with similar
v4l2 functions, thus simplifying several drivers.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The inode parameter at v4l_compat_translate_ioctl() were just passed over several
places just to keep compatible with fops.ioctl. However, it weren't used anywere.
This patch gets hid of this unused parameter.
Cc: Laurent Pinchart <laurent.pinchart@skynet.be>
Cc: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The kernel number of a v4l2 node (e.g. videoX, radioX or vbiX) is now
independent of the minor number. So instead of using the minor field
of the video_device struct one has to use the num field: this always
contains the kernel number of the device node.
I forgot about this when I did the v4l2 core change, so this patch
converts all drivers that use it in one go. Luckily the change is
trivial.
Cc: michael@mihu.de
Cc: mchehab@infradead.org
Cc: corbet@lwn.net
Cc: luca.risolia@studio.unibo.it
Cc: isely@pobox.com
Cc: pe1rxq@amsat.org
Cc: royale@zerezo.com
Cc: mkrufky@linuxtv.org
Cc: stoth@linuxtv.org
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jose reported:
I am using a Avermedia Volar X with af9015 driver(DVB-T).
The first time you use the card, first call reconfigure with MXL_QAM,
and when tune DVB-T it calls reconfigure with MXL_DVBT. But if you close
the frontend and open again, it calls reconfigure with MXL_QAM, but not
call reconfigure with MXL_DVBT because state->current_mode don't change
(is MXL_DVBT).
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This tuner was already supported by proxy as an FMD1216ME, however,
the MEX uses a different FM Radio IF so this addition is now required.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The IR controller has a couple quirks. It won't respond until some other
device on the bus is probed. To work around that, probe 0x50 first.
Then, since it won't respond to a zero-byte read, probe with a one-byte
read.
Signed-off-by: Brian Rogers <brian_rogers@comcast.net>
[mchehab.redhat.com: Fix merge conflicts and remove an unused var]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) for sponsoring
this development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) for sponsoring
this development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) for sponsoring
this development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Firmware selection is very tricky on this device. This patch do a better
selection of the proper firmware type, by using a code to hint if the
firmware to be loaded should be D2620 or D2633.
It also allows overriding the hint at the control structure.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The break after the return or goto serves no purpose.
Signed-off-by: Julia Lawall <julia@diku.dk>
Reviewed-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dont pass devptr in xc5000_attach, dont store it in xc5000_priv.
This pointer is passed into the tuner_callback function, which always
expects a pointer to fe->dvb->priv or i2c_adapter->algo_data.
This prevents future possible bugs in new drivers, such as using a "devptr"
other that the standard fe->dvb->priv in a DVB driver.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prevent an OOPS if xc5000_attach was called by tuner.ko before being called by
the DVB adapter driver. The OOPS occurs when a digital tune request is made
after tuner.ko is unloaded.
When tuner.ko is unloaded, it takes the xc5000_config structure with it.
Rather than storing a pointer to the xc5000_config structure, just store the
if_khz and tuner_callback inside the xc5000_priv internal state structure.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert xc5000 to use the hybrid_tuner_request_state and
hybrid_tuner_release_state macros to manage state sharing between
hybrid tuner instances.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the priv field and let video_get/set_drvdata use dev_get_drvdata
and dev_set_drvdata instead.
Convert all drivers that still used priv directly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) and CDI Brasil
(www.cdibrasil.com.br/) for sponsoring this development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Sistema Fenix (http://www.sistemafenix.com.br/) and CDI Brasil
(www.cdibrasil.com.br/) for sponsoring this development.
Signed-off-by: Gilberto <gilberto@sistemafenix.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The AMD ATI TV Wonder 600 has an XC3028L and *not* an XC3028, so we need to
load the proper firmware to prevent the device from overheating.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I need this so I can better isolate my linux email from my
corporate email.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed a lot of sparse warnings: mostly warnings about shadowed variables
and signed/unsigned mismatches.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
mxl5007 was forcing for its compilation:
In file included from drivers/media/common/tuners/mxl5007t.c:25:drivers/media/common/tuners/mxl5007t.h:80:1: warning: "CONFIG_MEDIA_TUNER_MXL5007T" redefined
In file included from <command-line>:0:
./include/linux/autoconf.h:2782:1: warning: this is the location of the previous definition
Probably, some temporary hack for testing.
Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The offset field of the scatterlist entry *after* the last valid scatterlist
entry was used instead of the first scatterlist entry (as was the intention
of this code).
This worked fine until the kzalloc of the sglist was replaced with kmalloc
and sg_init_table only zeroed the exact needed length. Apparently kzalloc
zeroes a bit more than is strictly necessary so the offset field was
always 0 in the past.
But now the offset field was suddenly random and this led to broken captures.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After commit d9b19199e4
(always enable FW_LOADER unless EMBEDDED=y) we can remove
the FW_LOADER select's and corresponding dependencies
on HOTPLUG.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
