The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
We introduce a feature that works like a combination of TCP_NAGLE and
TCP_CORK, but without some of the weaknesses of those. In particular,
we will not observe long delivery delays because of delayed acks, since
the algorithm itself decides if and when acks are to be sent from the
receiving peer.
- The nagle property as such is determined by manipulating a new
'maxnagle' field in struct tipc_sock. If certain conditions are met,
'maxnagle' will define max size of the messages which can be bundled.
If it is set to zero no messages are ever bundled, implying that the
nagle property is disabled.
- A socket with the nagle property enabled enters nagle mode when more
than 4 messages have been sent out without receiving any data message
from the peer.
- A socket leaves nagle mode whenever it receives a data message from
the peer.
In nagle mode, messages smaller than 'maxnagle' are accumulated in the
socket write queue. The last buffer in the queue is marked with a new
'ack_required' bit, which forces the receiving peer to send a CONN_ACK
message back to the sender upon reception.
The accumulated contents of the write queue is transmitted when one of
the following events or conditions occur.
- A CONN_ACK message is received from the peer.
- A data message is received from the peer.
- A SOCK_WAKEUP pseudo message is received from the link level.
- The write queue contains more than 64 1k blocks of data.
- The connection is being shut down.
- There is no CONN_ACK message to expect. I.e., there is currently
no outstanding message where the 'ack_required' bit was set. As a
consequence, the first message added after we enter nagle mode
is always sent directly with this bit set.
This new feature gives a 50-100% improvement of throughput for small
(i.e., less than MTU size) messages, while it might add up to one RTT
to latency time when the socket is in nagle mode.
Acked-by: Ying Xue <ying.xue@windreiver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, TIPC transports intra-node user data messages directly
socket to socket, hence shortcutting all the lower layers of the
communication stack. This gives TIPC very good intra node performance,
both regarding throughput and latency.
We now introduce a similar mechanism for TIPC data traffic across
network namespaces located in the same kernel. On the send path, the
call chain is as always accompanied by the sending node's network name
space pointer. However, once we have reliably established that the
receiving node is represented by a namespace on the same host, we just
replace the namespace pointer with the receiving node/namespace's
ditto, and follow the regular socket receive patch though the receiving
node. This technique gives us a throughput similar to the node internal
throughput, several times larger than if we let the traffic go though
the full network stacks. As a comparison, max throughput for 64k
messages is four times larger than TCP throughput for the same type of
traffic.
To meet any security concerns, the following should be noted.
- All nodes joining a cluster are supposed to have been be certified
and authenticated by mechanisms outside TIPC. This is no different for
nodes/namespaces on the same host; they have to auto discover each
other using the attached interfaces, and establish links which are
supervised via the regular link monitoring mechanism. Hence, a kernel
local node has no other way to join a cluster than any other node, and
have to obey to policies set in the IP or device layers of the stack.
- Only when a sender has established with 100% certainty that the peer
node is located in a kernel local namespace does it choose to let user
data messages, and only those, take the crossover path to the receiving
node/namespace.
- If the receiving node/namespace is removed, its namespace pointer
is invalidated at all peer nodes, and their neighbor link monitoring
will eventually note that this node is gone.
- To ensure the "100% certainty" criteria, and prevent any possible
spoofing, received discovery messages must contain a proof that the
sender knows a common secret. We use the hash mix of the sending
node/namespace for this purpose, since it can be accessed directly by
all other namespaces in the kernel. Upon reception of a discovery
message, the receiver checks this proof against all the local
namespaces'hash_mix:es. If it finds a match, that, along with a
matching node id and cluster id, this is deemed sufficient proof that
the peer node in question is in a local namespace, and a wormhole can
be opened.
- We should also consider that TIPC is intended to be a cluster local
IPC mechanism (just like e.g. UNIX sockets) rather than a network
protocol, and hence we think it can justified to allow it to shortcut the
lower protocol layers.
Regarding traceability, we should notice that since commit 6c9081a391
("tipc: add loopback device tracking") it is possible to follow the node
internal packet flow by just activating tcpdump on the loopback
interface. This will be true even for this mechanism; by activating
tcpdump on the involved nodes' loopback interfaces their inter-name
space messaging can easily be tracked.
v2:
- update 'net' pointer when node left/rejoined
v3:
- grab read/write lock when using node ref obj
v4:
- clone traffics between netns to loopback
Suggested-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many poll() handlers are lockless. Using skb_queue_empty_lockless()
instead of skb_queue_empty() is more appropriate.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk->sk_backlog.len can be written by BH handlers, and read
from process contexts in a lockless way.
Note the write side should also use WRITE_ONCE() or a variant.
We need some agreement about the best way to do this.
syzbot reported :
BUG: KCSAN: data-race in tcp_add_backlog / tcp_grow_window.isra.0
write to 0xffff88812665f32c of 4 bytes by interrupt on cpu 1:
sk_add_backlog include/net/sock.h:934 [inline]
tcp_add_backlog+0x4a0/0xcc0 net/ipv4/tcp_ipv4.c:1737
tcp_v4_rcv+0x1aba/0x1bf0 net/ipv4/tcp_ipv4.c:1925
ip_protocol_deliver_rcu+0x51/0x470 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5004
__netif_receive_skb+0x37/0xf0 net/core/dev.c:5118
netif_receive_skb_internal+0x59/0x190 net/core/dev.c:5208
napi_skb_finish net/core/dev.c:5671 [inline]
napi_gro_receive+0x28f/0x330 net/core/dev.c:5704
receive_buf+0x284/0x30b0 drivers/net/virtio_net.c:1061
virtnet_receive drivers/net/virtio_net.c:1323 [inline]
virtnet_poll+0x436/0x7d0 drivers/net/virtio_net.c:1428
napi_poll net/core/dev.c:6352 [inline]
net_rx_action+0x3ae/0xa50 net/core/dev.c:6418
read to 0xffff88812665f32c of 4 bytes by task 7292 on cpu 0:
tcp_space include/net/tcp.h:1373 [inline]
tcp_grow_window.isra.0+0x6b/0x480 net/ipv4/tcp_input.c:413
tcp_event_data_recv+0x68f/0x990 net/ipv4/tcp_input.c:717
tcp_rcv_established+0xbfe/0xf50 net/ipv4/tcp_input.c:5618
tcp_v4_do_rcv+0x381/0x4e0 net/ipv4/tcp_ipv4.c:1542
sk_backlog_rcv include/net/sock.h:945 [inline]
__release_sock+0x135/0x1e0 net/core/sock.c:2427
release_sock+0x61/0x160 net/core/sock.c:2943
tcp_recvmsg+0x63b/0x1a30 net/ipv4/tcp.c:2181
inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838
sock_recvmsg_nosec net/socket.c:871 [inline]
sock_recvmsg net/socket.c:889 [inline]
sock_recvmsg+0x92/0xb0 net/socket.c:885
sock_read_iter+0x15f/0x1e0 net/socket.c:967
call_read_iter include/linux/fs.h:1864 [inline]
new_sync_read+0x389/0x4f0 fs/read_write.c:414
__vfs_read+0xb1/0xc0 fs/read_write.c:427
vfs_read fs/read_write.c:461 [inline]
vfs_read+0x143/0x2c0 fs/read_write.c:446
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 7292 Comm: syz-fuzzer Not tainted 5.3.0+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
sk_add_backlog() callers usually read sk->sk_rcvbuf without
owning the socket lock. This means sk_rcvbuf value can
be changed by other cpus, and KCSAN complains.
Add READ_ONCE() annotations to document the lockless nature
of these reads.
Note that writes over sk_rcvbuf should also use WRITE_ONCE(),
but this will be done in separate patches to ease stable
backports (if we decide this is relevant for stable trees).
BUG: KCSAN: data-race in tcp_add_backlog / tcp_recvmsg
write to 0xffff88812ab369f8 of 8 bytes by interrupt on cpu 1:
__sk_add_backlog include/net/sock.h:902 [inline]
sk_add_backlog include/net/sock.h:933 [inline]
tcp_add_backlog+0x45a/0xcc0 net/ipv4/tcp_ipv4.c:1737
tcp_v4_rcv+0x1aba/0x1bf0 net/ipv4/tcp_ipv4.c:1925
ip_protocol_deliver_rcu+0x51/0x470 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5004
__netif_receive_skb+0x37/0xf0 net/core/dev.c:5118
netif_receive_skb_internal+0x59/0x190 net/core/dev.c:5208
napi_skb_finish net/core/dev.c:5671 [inline]
napi_gro_receive+0x28f/0x330 net/core/dev.c:5704
receive_buf+0x284/0x30b0 drivers/net/virtio_net.c:1061
virtnet_receive drivers/net/virtio_net.c:1323 [inline]
virtnet_poll+0x436/0x7d0 drivers/net/virtio_net.c:1428
napi_poll net/core/dev.c:6352 [inline]
net_rx_action+0x3ae/0xa50 net/core/dev.c:6418
read to 0xffff88812ab369f8 of 8 bytes by task 7271 on cpu 0:
tcp_recvmsg+0x470/0x1a30 net/ipv4/tcp.c:2047
inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838
sock_recvmsg_nosec net/socket.c:871 [inline]
sock_recvmsg net/socket.c:889 [inline]
sock_recvmsg+0x92/0xb0 net/socket.c:885
sock_read_iter+0x15f/0x1e0 net/socket.c:967
call_read_iter include/linux/fs.h:1864 [inline]
new_sync_read+0x389/0x4f0 fs/read_write.c:414
__vfs_read+0xb1/0xc0 fs/read_write.c:427
vfs_read fs/read_write.c:461 [inline]
vfs_read+0x143/0x2c0 fs/read_write.c:446
ksys_read+0xd5/0x1b0 fs/read_write.c:587
__do_sys_read fs/read_write.c:597 [inline]
__se_sys_read fs/read_write.c:595 [inline]
__x64_sys_read+0x4c/0x60 fs/read_write.c:595
do_syscall_64+0xcf/0x2f0 arch/x86/entry/common.c:296
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 7271 Comm: syz-fuzzer Not tainted 5.3.0+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Benefit from the fact that the generic netlink code can parse the attrs
for dumpit op and avoid need to parse it in the op callback.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The policy for handling the skb list locks on the send and receive paths
is simple.
- On the send path we never need to grab the lock on the 'xmitq' list
when the destination is an exernal node.
- On the receive path we always need to grab the lock on the 'inputq'
list, irrespective of source node.
However, when transmitting node local messages those will eventually
end up on the receive path of a local socket, meaning that the argument
'xmitq' in tipc_node_xmit() will become the 'ínputq' argument in the
function tipc_sk_rcv(). This has been handled by always initializing
the spinlock of the 'xmitq' list at message creation, just in case it
may end up on the receive path later, and despite knowing that the lock
in most cases never will be used.
This approach is inaccurate and confusing, and has also concealed the
fact that the stated 'no lock grabbing' policy for the send path is
violated in some cases.
We now clean up this by never initializing the lock at message creation,
instead doing this at the moment we find that the message actually will
enter the receive path. At the same time we fix the four locations
where we incorrectly access the spinlock on the send/error path.
This patch also reverts commit d12cffe932 ("tipc: ensure head->lock
is initialised") which has now become redundant.
CC: Eric Dumazet <edumazet@google.com>
Reported-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 517d7c79bd ("tipc: fix hanging poll() for stream sockets")
introduced a regression for clients using non-blocking sockets.
After the commit, we send EPOLLOUT event to the client even in
TIPC_CONNECTING state. This causes the subsequent send() to fail
with ENOTCONN, as the socket is still not in TIPC_ESTABLISHED state.
In this commit, we:
- improve the fix for hanging poll() by replacing sk_data_ready()
with sk_state_change() to wake up all clients.
- revert the faulty updates introduced by commit 517d7c79bd
("tipc: fix hanging poll() for stream sockets").
Fixes: 517d7c79bd ("tipc: fix hanging poll() for stream sockets")
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have two levels of strict validation:
1) liberal (default)
- undefined (type >= max) & NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
- garbage at end of message accepted
2) strict (opt-in)
- NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
Split out parsing strictness into four different options:
* TRAILING - check that there's no trailing data after parsing
attributes (in message or nested)
* MAXTYPE - reject attrs > max known type
* UNSPEC - reject attributes with NLA_UNSPEC policy entries
* STRICT_ATTRS - strictly validate attribute size
The default for future things should be *everything*.
The current *_strict() is a combination of TRAILING and MAXTYPE,
and is renamed to _deprecated_strict().
The current regular parsing has none of this, and is renamed to
*_parse_deprecated().
Additionally it allows us to selectively set one of the new flags
even on old policies. Notably, the UNSPEC flag could be useful in
this case, since it can be arranged (by filling in the policy) to
not be an incompatible userspace ABI change, but would then going
forward prevent forgetting attribute entries. Similar can apply
to the POLICY flag.
We end up with the following renames:
* nla_parse -> nla_parse_deprecated
* nla_parse_strict -> nla_parse_deprecated_strict
* nlmsg_parse -> nlmsg_parse_deprecated
* nlmsg_parse_strict -> nlmsg_parse_deprecated_strict
* nla_parse_nested -> nla_parse_nested_deprecated
* nla_validate_nested -> nla_validate_nested_deprecated
Using spatch, of course:
@@
expression TB, MAX, HEAD, LEN, POL, EXT;
@@
-nla_parse(TB, MAX, HEAD, LEN, POL, EXT)
+nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression TB, MAX, NLA, POL, EXT;
@@
-nla_parse_nested(TB, MAX, NLA, POL, EXT)
+nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT)
@@
expression START, MAX, POL, EXT;
@@
-nla_validate_nested(START, MAX, POL, EXT)
+nla_validate_nested_deprecated(START, MAX, POL, EXT)
@@
expression NLH, HDRLEN, MAX, POL, EXT;
@@
-nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT)
+nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT)
For this patch, don't actually add the strict, non-renamed versions
yet so that it breaks compile if I get it wrong.
Also, while at it, make nla_validate and nla_parse go down to a
common __nla_validate_parse() function to avoid code duplication.
Ultimately, this allows us to have very strict validation for every
new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the
next patch, while existing things will continue to work as is.
In effect then, this adds fully strict validation for any new command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if the NLA_F_NESTED flag was introduced more than 11 years ago, most
netlink based interfaces (including recently added ones) are still not
setting it in kernel generated messages. Without the flag, message parsers
not aware of attribute semantics (e.g. wireshark dissector or libmnl's
mnl_nlmsg_fprintf()) cannot recognize nested attributes and won't display
the structure of their contents.
Unfortunately we cannot just add the flag everywhere as there may be
userspace applications which check nlattr::nla_type directly rather than
through a helper masking out the flags. Therefore the patch renames
nla_nest_start() to nla_nest_start_noflag() and introduces nla_nest_start()
as a wrapper adding NLA_F_NESTED. The calls which add NLA_F_NESTED manually
are rewritten to use nla_nest_start().
Except for changes in include/net/netlink.h, the patch was generated using
this semantic patch:
@@ expression E1, E2; @@
-nla_nest_start(E1, E2)
+nla_nest_start_noflag(E1, E2)
@@ expression E1, E2; @@
-nla_nest_start_noflag(E1, E2 | NLA_F_NESTED)
+nla_nest_start(E1, E2)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using TIPC_SOCK_RECVQ_DEPTH for getsockopt(), it returns the
number of buffers in receive socket buffer which is not so helpful
for user space applications.
This commit introduces the new option TIPC_SOCK_RECVQ_USED which
returns the current allocated bytes of the receive socket buffer.
This helps user space applications dimension its buffer usage to
avoid buffer overload issue.
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb free-ed in:
1/ condition 1: tipc_sk_filter_rcv -> tipc_sk_proto_rcv
2/ condition 2: tipc_sk_filter_rcv -> tipc_group_filter_msg
This leads to a "use-after-free" access in the next condition.
We fix this by intializing the variable at declaration, then it is safe
to check this variable to continue processing if condition matches.
syzbot report:
==================================================================
BUG: KASAN: use-after-free in tipc_sk_filter_rcv+0x2166/0x34f0
net/tipc/socket.c:2167
Read of size 4 at addr ffff88808ea58534 by task kworker/u4:0/7
CPU: 0 PID: 7 Comm: kworker/u4:0 Not tainted 5.0.0+ #61
Hardware name: Google Google Compute Engine/Google Compute Engine,
BIOS Google 01/01/2011
Workqueue: tipc_send tipc_conn_send_work
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187
kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
__asan_report_load4_noabort+0x14/0x20 mm/kasan/generic_report.c:131
tipc_sk_filter_rcv+0x2166/0x34f0 net/tipc/socket.c:2167
tipc_sk_enqueue net/tipc/socket.c:2254 [inline]
tipc_sk_rcv+0xc45/0x25a0 net/tipc/socket.c:2305
tipc_topsrv_kern_evt+0x3b7/0x580 net/tipc/topsrv.c:610
tipc_conn_send_to_sock+0x43e/0x5f0 net/tipc/topsrv.c:283
tipc_conn_send_work+0x65/0x80 net/tipc/topsrv.c:303
process_one_work+0x98e/0x1790 kernel/workqueue.c:2269
worker_thread+0x98/0xe40 kernel/workqueue.c:2415
kthread+0x357/0x430 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
Reported-by: syzbot+e863893591cc7a622e40@syzkaller.appspotmail.com
Fixes: c55c8eda ("tipc: smooth change between replicast and broadcast")
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a multicast stream may start out using replicast, because
there are few destinations, and then it should ideally switch to
L2/broadcast IGMP/multicast when the number of destinations grows beyond
a certain limit. The opposite should happen when the number decreases
below the limit.
To eliminate the risk of message reordering caused by method change,
a sending socket must stick to a previously selected method until it
enters an idle period of 5 seconds. Means there is a 5 seconds pause
in the traffic from the sender socket.
If the sender never makes such a pause, the method will never change,
and transmission may become very inefficient as the cluster grows.
With this commit, we allow such a switch between replicast and
broadcast without any need for a traffic pause.
Solution is to send a dummy message with only the header, also with
the SYN bit set, via broadcast or replicast. For the data message,
the SYN bit is set and sending via replicast or broadcast (inverse
method with dummy).
Then, at receiving side any messages follow first SYN bit message
(data or dummy message), they will be held in deferred queue until
another pair (dummy or data message) arrived in other link.
v2: reverse christmas tree declaration
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We move the check that prevents connecting service ranges to after
the RDM/DGRAM check, and move address sanity control to a separate
function that also validates the service range.
Fixes: 23998835be ("tipc: improve address sanity check in tipc_connect()")
Signed-off-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nla_nest_start may fail. The fix check its status and returns
-EMSGSIZE in case it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix regression bug introduced in
commit 365ad353c2 ("tipc: reduce risk of user starvation during link
congestion")
Only signal -EDESTADDRREQ for RDM/DGRAM if we don't have a cached
sockaddr.
Fixes: 365ad353c2 ("tipc: reduce risk of user starvation during link congestion")
Signed-off-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending multicast messages via blocking socket,
if sending link is congested (tsk->cong_link_cnt is set to 1),
the sending thread will be put into sleeping state. However,
tipc_sk_filter_rcv() is called under socket spin lock but
tipc_wait_for_cond() is not. So, there is no guarantee that
the setting of tsk->cong_link_cnt to 0 in tipc_sk_proto_rcv() in
CPU-1 will be perceived by CPU-0. If that is the case, the sending
thread in CPU-0 after being waken up, will continue to see
tsk->cong_link_cnt as 1 and put the sending thread into sleeping
state again. The sending thread will sleep forever.
CPU-0 | CPU-1
tipc_wait_for_cond() |
{ |
// condition_ = !tsk->cong_link_cnt |
while ((rc_ = !(condition_))) { |
... |
release_sock(sk_); |
wait_woken(); |
| if (!sock_owned_by_user(sk))
| tipc_sk_filter_rcv()
| {
| ...
| tipc_sk_proto_rcv()
| {
| ...
| tsk->cong_link_cnt--;
| ...
| sk->sk_write_space(sk);
| ...
| }
| ...
| }
sched_annotate_sleep(); |
lock_sock(sk_); |
remove_wait_queue(); |
} |
} |
This commit fixes it by adding memory barrier to tipc_sk_proto_rcv()
and tipc_wait_for_cond().
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit replaces schedule_timeout() with wait_woken()
in function tipc_wait_for_rcvmsg(). wait_woken() uses
memory barriers in its implementation to avoid potential
race condition when putting a process into sleeping state
and then waking it up.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 844cf763fb ("tipc: make macro tipc_wait_for_cond() smp safe")
replaced finish_wait() with remove_wait_queue() but still used
prepare_to_wait(). This causes unnecessary conditional
checking before adding to wait queue in prepare_to_wait().
This commit replaces prepare_to_wait() with add_wait_queue()
as the pair function with remove_wait_queue().
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warnings:
net/tipc/link.c:1125:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
net/tipc/socket.c:736:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
net/tipc/socket.c:2418:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit adds the new trace_events for TIPC socket object:
trace_tipc_sk_create()
trace_tipc_sk_poll()
trace_tipc_sk_sendmsg()
trace_tipc_sk_sendmcast()
trace_tipc_sk_sendstream()
trace_tipc_sk_filter_rcv()
trace_tipc_sk_advance_rx()
trace_tipc_sk_rej_msg()
trace_tipc_sk_drop_msg()
trace_tipc_sk_release()
trace_tipc_sk_shutdown()
trace_tipc_sk_overlimit1()
trace_tipc_sk_overlimit2()
Also, enables the traces for the following cases:
- When user creates a TIPC socket;
- When user calls poll() on TIPC socket;
- When user sends a dgram/mcast/stream message.
- When a message is put into the socket 'sk_receive_queue';
- When a message is released from the socket 'sk_receive_queue';
- When a message is rejected (e.g. due to no port, invalid, etc.);
- When a message is dropped (e.g. due to wrong message type);
- When socket is released;
- When socket is shutdown;
- When socket rcvq's allocation is overlimit (> 90%);
- When socket rcvq + bklq's allocation is overlimit (> 90%);
- When the 'TIPC_ERR_OVERLOAD/2' issue happens;
Note:
a) All the socket traces are designed to be able to trace on a specific
socket by either using the 'event filtering' feature on a known socket
'portid' value or the sysctl file:
/proc/sys/net/tipc/sk_filter
The file determines a 'tuple' for what socket should be traced:
(portid, sock type, name type, name lower, name upper)
where:
+ 'portid' is the socket portid generated at socket creating, can be
found in the trace outputs or the 'tipc socket list' command printouts;
+ 'sock type' is the socket type (1 = SOCK_TREAM, ...);
+ 'name type', 'name lower' and 'name upper' are the service name being
connected to or published by the socket.
Value '0' means 'ANY', the default tuple value is (0, 0, 0, 0, 0) i.e.
the traces happen for every sockets with no filter.
b) The 'tipc_sk_overlimit1/2' event is also a conditional trace_event
which happens when the socket receive queue (and backlog queue) is
about to be overloaded, when the queue allocation is > 90%. Then, when
the trace is enabled, the last skbs leading to the TIPC_ERR_OVERLOAD/2
issue can be traced.
The trace event is designed as an 'upper watermark' notification that
the other traces (e.g. 'tipc_sk_advance_rx' vs 'tipc_sk_filter_rcv') or
actions can be triggerred in the meanwhile to see what is going on with
the socket queue.
In addition, the 'trace_tipc_sk_dump()' is also placed at the
'TIPC_ERR_OVERLOAD/2' case, so the socket and last skb can be dumped
for post-analysis.
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As for the sake of debugging/tracing, the commit enables tracepoints in
TIPC along with some general trace_events as shown below. It also
defines some 'tipc_*_dump()' functions that allow to dump TIPC object
data whenever needed, that is, for general debug purposes, ie. not just
for the trace_events.
The following trace_events are now available:
- trace_tipc_skb_dump(): allows to trace and dump TIPC msg & skb data,
e.g. message type, user, droppable, skb truesize, cloned skb, etc.
- trace_tipc_list_dump(): allows to trace and dump any TIPC buffers or
queues, e.g. TIPC link transmq, socket receive queue, etc.
- trace_tipc_sk_dump(): allows to trace and dump TIPC socket data, e.g.
sk state, sk type, connection type, rmem_alloc, socket queues, etc.
- trace_tipc_link_dump(): allows to trace and dump TIPC link data, e.g.
link state, silent_intv_cnt, gap, bc_gap, link queues, etc.
- trace_tipc_node_dump(): allows to trace and dump TIPC node data, e.g.
node state, active links, capabilities, link entries, etc.
How to use:
Put the trace functions at any places where we want to dump TIPC data
or events.
Note:
a) The dump functions will generate raw data only, that is, to offload
the trace event's processing, it can require a tool or script to parse
the data but this should be simple.
b) The trace_tipc_*_dump() should be reserved for a failure cases only
(e.g. the retransmission failure case) or where we do not expect to
happen too often, then we can consider enabling these events by default
since they will almost not take any effects under normal conditions,
but once the rare condition or failure occurs, we get the dumped data
fully for post-analysis.
For other trace purposes, we can reuse these trace classes as template
but different events.
c) A trace_event is only effective when we enable it. To enable the
TIPC trace_events, echo 1 to 'enable' files in the events/tipc/
directory in the 'debugfs' file system. Normally, they are located at:
/sys/kernel/debug/tracing/events/tipc/
For example:
To enable the tipc_link_dump event:
echo 1 > /sys/kernel/debug/tracing/events/tipc/tipc_link_dump/enable
To enable all the TIPC trace_events:
echo 1 > /sys/kernel/debug/tracing/events/tipc/enable
To collect the trace data:
cat trace
or
cat trace_pipe > /trace.out &
To disable all the TIPC trace_events:
echo 0 > /sys/kernel/debug/tracing/events/tipc/enable
To clear the trace buffer:
echo > trace
d) Like the other trace_events, the feature like 'filter' or 'trigger'
is also usable for the tipc trace_events.
For more details, have a look at:
Documentation/trace/ftrace.txt
MAINTAINERS | add two new files 'trace.h' & 'trace.c' in tipc
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit 143ece654f ("tipc: check tsk->group in tipc_wait_for_cond()")
we have to reload grp->dests too after we re-take the sock lock.
This means we need to move the dsts check after tipc_wait_for_cond()
too.
Fixes: 75da2163db ("tipc: introduce communication groups")
Reported-and-tested-by: syzbot+99f20222fc5018d2b97a@syzkaller.appspotmail.com
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_wait_for_cond() drops socket lock before going to sleep,
but tsk->group could be freed right after that release_sock().
So we have to re-check and reload tsk->group after it wakes up.
After this patch, tipc_wait_for_cond() returns -ERESTARTSYS when
tsk->group is NULL, instead of continuing with the assumption of
a non-NULL tsk->group.
(It looks like 'dsts' should be re-checked and reloaded too, but
it is a different bug.)
Similar for tipc_send_group_unicast() and tipc_send_group_anycast().
Reported-by: syzbot+10a9db47c3a0e13eb31c@syzkaller.appspotmail.com
Fixes: b7d4263551 ("tipc: introduce flow control for group broadcast messages")
Fixes: ee106d7f94 ("tipc: introduce group anycast messaging")
Fixes: 27bd9ec027 ("tipc: introduce group unicast messaging")
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lock_sock() must be used in process context to be race-free with
other lock_sock() callers, for example, tipc_release(). Otherwise
using the spinlock directly can't serialize a parallel tipc_release().
As it is blocking, we have to hold the sock refcnt before
rhashtable_walk_stop() and release it after rhashtable_walk_start().
Fixes: 07f6c4bc04 ("tipc: convert tipc reference table to use generic rhashtable")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code for reading ancillary data from a received buffer is assuming
the buffer is linear. To make this assumption true we have to linearize
the buffer before message data is read.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit dd979b4df8.
This broke tcp_poll for SMC fallback: An AF_SMC socket establishes an
internal TCP socket for the initial handshake with the remote peer.
Whenever the SMC connection can not be established this TCP socket is
used as a fallback. All socket operations on the SMC socket are then
forwarded to the TCP socket. In case of poll, the file->private_data
pointer references the SMC socket because the TCP socket has no file
assigned. This causes tcp_poll to wait on the wrong socket.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>
In tipc_sk_filter_rcv(), when we detect protocol messages with error we
call tipc_sk_conn_proto_rcv() and let it reset the connection and notify
the socket by calling sk->sk_state_change().
However, tipc_sk_filter_rcv() may have been called from the function
tipc_backlog_rcv(), in which case the socket lock is held and the socket
already awake. This means that the sk_state_change() call is ignored and
the error notification lost. Now the receive queue will remain empty and
the socket sleeps forever.
In this commit, we convert the protocol message into a connection abort
message and enqueue it into the socket's receive queue. By this addition
to the above state change we cover all conditions.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Default socket receive buffer size for a listener socket is 2Mb. For
each arriving empty SYN, the linux kernel allocates a 768 bytes buffer.
This means that a listener socket can serve maximum 2700 simultaneous
empty connection setup requests before it hits a receive buffer
overflow, and much fewer if the SYN is carrying any significant
amount of data.
When this happens the setup request is rejected, and the client
receives an ECONNREFUSED error.
This commit mitigates this problem by letting the client socket try to
retransmit the SYN message multiple times when it sees it rejected with
the code TIPC_ERR_OVERLOAD. Retransmission is done at random intervals
in the range of [100 ms, setup_timeout / 4], as many times as there is
room for within the setup timeout limit.
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Messages intended for intitating a connection are currently
indistinguishable from regular datagram messages. The TIPC
protocol specification defines bit 17 in word 0 as a SYN bit
to allow sanity check of such messages in the listening socket,
but this has so far never been implemented.
We do that in this commit.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We refactor the function tipc_sk_filter_connect(), both to make it
more readable and as a preparation for the next commit.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We refactor this function as a preparation for the coming commits in
the same series.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of implicit connect message with data > 1K, the flow
control accounting is incorrect. At this state, the socket does not
know the peer nodes capability and falls back to legacy flow control
by return 1, however the receiver of this message will perform the
new block accounting. This leads to a slack and eventually traffic
disturbance.
In this commit, we perform tipc_node_get_capabilities() at implicit
connect and perform accounting based on the peer's capability.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__tipc_nl_compat_dumpit() uses a netlink_callback on stack,
so the only way to align it with other ->dumpit() call path
is calling tipc_dump_start() and tipc_dump_done() directly
inside it. Otherwise ->dumpit() would always get NULL from
cb->args[].
But tipc_dump_start() uses sock_net(cb->skb->sk) to retrieve
net pointer, the cb->skb here doesn't set skb->sk, the net pointer
is saved in msg->net instead, so introduce a helper function
__tipc_dump_start() to pass in msg->net.
Ying pointed out cb->args[0...3] are already used by other
callbacks on this call path, so we can't use cb->args[0] any
more, use cb->args[4] instead.
Fixes: 9a07efa9ae ("tipc: switch to rhashtable iterator")
Reported-and-tested-by: syzbot+e93a2c41f91b8e2c7d9b@syzkaller.appspotmail.com
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before we unlock the sock in tipc_release(), we have to
detach sk->sk_socket from sk, otherwise a parallel
tipc_sk_fill_sock_diag() could stil read it after we
free this socket.
Fixes: c30b70deb5 ("tipc: implement socket diagnostics for AF_TIPC")
Reported-and-tested-by: syzbot+48804b87c16588ad491d@syzkaller.appspotmail.com
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported a use-after-free in tipc_group_fill_sock_diag(),
where tipc_group_fill_sock_diag() still reads tsk->group meanwhile
tipc_group_delete() just deletes it in tipc_release().
tipc_nl_sk_walk() aims to lock this sock when walking each sock
in the hash table to close race conditions with sock changes like
this one, by acquiring tsk->sk.sk_lock.slock spinlock, unfortunately
this doesn't work at all. All non-BH call path should take
lock_sock() instead to make it work.
tipc_nl_sk_walk() brutally iterates with raw rht_for_each_entry_rcu()
where RCU read lock is required, this is the reason why lock_sock()
can't be taken on this path. This could be resolved by switching to
rhashtable iterator API's, where taking a sleepable lock is possible.
Also, the iterator API's are friendly for restartable calls like
diag dump, the last position is remembered behind the scence,
all we need to do here is saving the iterator into cb->args[].
I tested this with parallel tipc diag dump and thousands of tipc
socket creation and release, no crash or memory leak.
Reported-by: syzbot+b9c8f3ab2994b7cd1625@syzkaller.appspotmail.com
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rhashtable_walk_exit() must be paired with rhashtable_walk_enter().
Fixes: 40f9f43970 ("tipc: Fix tipc_sk_reinit race conditions")
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variables 'tn' and 'oport' are being assigned but are never used hence
they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'oport' set but not used [-Wunused-but-set-variable]
warning: variable 'tn' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wait_address argument is always directly derived from the filp
argument, so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple overlapping changes in stmmac driver.
Adjust skb_gro_flush_final_remcsum function signature to make GRO list
changes in net-next, as per Stephen Rothwell's example merge
resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit extends the existing TIPC socket diagnostics framework
for information related to TIPC group communication.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
