These drivers are GPIO drivers, and the do not need to use the
legacy header in <linux/gpio.h>, go directly for
<linux/gpio/driver.h> instead.
Replace any use of GPIOF_* with 0/1, these flags are for
consumers, not drivers.
Get rid of a few gpio_to_irq() users that was littering
around the place, use local callbacks or avoid using it at
all.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Omit extra messages for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kernel cycle:
Core:
- The pin control Kconfig entry PINCTRL is now turned into
a menuconfig option. This obviously has the implication of
making the subsystem menu visible in menuconfig. This is
happening because of two things:
- Intel have started to deploy and depend on pin controllers
in a way that is affecting users directly. This happens
on the highly integrated laptop chipsets named after
geographical places: baytrail, broxton, cannonlake,
cedarfork, cherryview, denverton, geminilake, lewisburg,
merrifield, sunrisepoint... It started a while back and
now it is ever more evident that this is crucial
infrastructure for x86 laptops and not an embedded
obscurity anymore. Users need to be aware.
- Pin control expanders on I2C and SPI that are
arch-agnostic. Currently Semtech SX150X and Microchip
MCP28x08 but more are expected. Users will have to be
able to configure these in directly for their set-up.
- Just go and select GPIOLIB now that we made sure that
GPIOLIB is a very vanilla subsystem. Do not depend on
it, if we need it, select it.
- Exposing the pin control subsystem in menuconfig uncovered
a bunch of obscure bugs that are now hopefully fixed,
all more or less pertaining to Blackfin.
- Unified namespace for cross-calls between pin control and
GPIO.
- New support for clock skew/delay generic DT bindings
and generic pin config options for this.
- Minor documentation improvements.
Various:
- The Renesas SH-PFC pin controller has evolved a lot. It seems
Renesas are churning out new SoCs by the minute.
- A bunch of non-critical fixes for the Rockchip driver.
- Improve the use of library functions instead of open coding.
- Support the MCP28018 variant in the MCP28x08 driver.
- Static constifying.
-----BEGIN PGP SIGNATURE-----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=kj/b
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.15 kernel cycle:
Core:
- The pin control Kconfig entry PINCTRL is now turned into a
menuconfig option. This obviously has the implication of making the
subsystem menu visible in menuconfig. This is happening because of
two things:
(a) Intel have started to deploy and depend on pin controllers in
a way that is affecting users directly. This happens on the
highly integrated laptop chipsets named after geographical
places: baytrail, broxton, cannonlake, cedarfork, cherryview,
denverton, geminilake, lewisburg, merrifield, sunrisepoint...
It started a while back and now it is ever more evident that
this is crucial infrastructure for x86 laptops and not an
embedded obscurity anymore. Users need to be aware.
(b) Pin control expanders on I2C and SPI that are arch-agnostic.
Currently Semtech SX150X and Microchip MCP28x08 but more are
expected. Users will have to be able to configure these in
directly for their set-up.
- Just go and select GPIOLIB now that we made sure that GPIOLIB is a
very vanilla subsystem. Do not depend on it, if we need it, select
it.
- Exposing the pin control subsystem in menuconfig uncovered a bunch
of obscure bugs that are now hopefully fixed, all more or less
pertaining to Blackfin.
- Unified namespace for cross-calls between pin control and GPIO.
- New support for clock skew/delay generic DT bindings and generic
pin config options for this.
- Minor documentation improvements.
Various:
- The Renesas SH-PFC pin controller has evolved a lot. It seems
Renesas are churning out new SoCs by the minute.
- A bunch of non-critical fixes for the Rockchip driver.
- Improve the use of library functions instead of open coding.
- Support the MCP28018 variant in the MCP28x08 driver.
- Static constifying"
* tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (91 commits)
pinctrl: gemini: Fix missing pad descriptions
pinctrl: Add some depends on HAS_IOMEM
pinctrl: samsung/s3c24xx: add CONFIG_OF dependency
pinctrl: gemini: Fix GMAC groups
pinctrl: qcom: spmi-gpio: Add pmi8994 gpio support
pinctrl: ti-iodelay: remove redundant unused variable dev
pinctrl: max77620: Use common error handling code in max77620_pinconf_set()
pinctrl: gemini: Implement clock skew/delay config
pinctrl: gemini: Use generic DT parser
pinctrl: Add skew-delay pin config and bindings
pinctrl: armada-37xx: Add edge both type gpio irq support
pinctrl: uniphier: remove eMMC hardware reset pin-mux
pinctrl: rockchip: Add iomux-route switching support for rk3288
pinctrl: intel: Add Intel Cedar Fork PCH pin controller support
pinctrl: intel: Make offset to interrupt status register configurable
pinctrl: sunxi: Enforce the strict mode by default
pinctrl: sunxi: Disable strict mode for old pinctrl drivers
pinctrl: sunxi: Introduce the strict flag
pinctrl: sh-pfc: Save/restore registers for PSCI system suspend
pinctrl: sh-pfc: r8a7796: Use generic IOCTRL register description
...
CORE:
- Fix the semantics of raw GPIO to actually be raw. No
inversion semantics as before, but also no open draining,
and allow the raw operations to affect lines used for
interrupts as the caller supposedly knows what they are
doing if they are getting the big hammer.
- Rewrote the __inner_function() notation calls to names that
make more sense. I just find this kind of code disturbing.
- Drop the .irq_base() field from the gpiochip since now all
IRQs are mapped dynamically. This is nice.
- Support for .get_multiple() in the core driver API. This
allows us to read several GPIO lines with a single
register read. This has high value for some usecases: it
can be used to create oscilloscopes and signal analyzers
and other things that rely on reading several lines at
exactly the same instant. Also a generally nice
optimization. This uses the new assign_bit() macro from
the bitops lib that was ACKed by Andrew Morton and
is implemented for two drivers, one of them being the
generic MMIO driver so everyone using that will be able
to benefit from this.
- Do not allow requests of Open Drain and Open Source
setting of a GPIO line simultaneously. If the hardware
actually supports enabling both at the same time the
electrical result would be disastrous.
- A new interrupt chip core helper. This will be helpful
to deal with "banked" GPIOs, which means GPIO controllers
with several logical blocks of GPIO inside them. This
is several gpiochips per device in the device model, in
contrast to the case when there is a 1-to-1 relationship
between a device and a gpiochip.
NEW DRIVERS:
- Maxim MAX3191x industrial serializer, a very interesting
piece of professional I/O hardware.
- Uniphier GPIO driver. This is the GPIO block from the
recent Socionext (ex Fujitsu and Panasonic) platform.
- Tegra 186 driver. This is based on the new banked GPIO
infrastructure.
OTHER IMPROVEMENTS:
- Some documentation improvements.
- Wakeup support for the DesignWare DWAPB GPIO controller.
- Reset line support on the DesignWare DWAPB GPIO controller.
- Several non-critical bug fixes and improvements for the
Broadcom BRCMSTB driver.
- Misc non-critical bug fixes like exotic errorpaths, removal
of dead code etc.
- Explicit comments on fall-through switch() statements.
-----BEGIN PGP SIGNATURE-----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=8Mon
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.15 kernel cycle:
Core:
- Fix the semantics of raw GPIO to actually be raw. No inversion
semantics as before, but also no open draining, and allow the raw
operations to affect lines used for interrupts as the caller
supposedly knows what they are doing if they are getting the big
hammer.
- Rewrote the __inner_function() notation calls to names that make
more sense. I just find this kind of code disturbing.
- Drop the .irq_base() field from the gpiochip since now all IRQs are
mapped dynamically. This is nice.
- Support for .get_multiple() in the core driver API. This allows us
to read several GPIO lines with a single register read. This has
high value for some usecases: it can be used to create
oscilloscopes and signal analyzers and other things that rely on
reading several lines at exactly the same instant. Also a generally
nice optimization. This uses the new assign_bit() macro from the
bitops lib that was ACKed by Andrew Morton and is implemented for
two drivers, one of them being the generic MMIO driver so everyone
using that will be able to benefit from this.
- Do not allow requests of Open Drain and Open Source setting of a
GPIO line simultaneously. If the hardware actually supports
enabling both at the same time the electrical result would be
disastrous.
- A new interrupt chip core helper. This will be helpful to deal with
"banked" GPIOs, which means GPIO controllers with several logical
blocks of GPIO inside them. This is several gpiochips per device in
the device model, in contrast to the case when there is a 1-to-1
relationship between a device and a gpiochip.
New drivers:
- Maxim MAX3191x industrial serializer, a very interesting piece of
professional I/O hardware.
- Uniphier GPIO driver. This is the GPIO block from the recent
Socionext (ex Fujitsu and Panasonic) platform.
- Tegra 186 driver. This is based on the new banked GPIO
infrastructure.
Other improvements:
- Some documentation improvements.
- Wakeup support for the DesignWare DWAPB GPIO controller.
- Reset line support on the DesignWare DWAPB GPIO controller.
- Several non-critical bug fixes and improvements for the Broadcom
BRCMSTB driver.
- Misc non-critical bug fixes like exotic errorpaths, removal of dead
code etc.
- Explicit comments on fall-through switch() statements"
* tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (65 commits)
gpio: tegra186: Remove tegra186_gpio_lock_class
gpio: rcar: Add r8a77995 (R-Car D3) support
pinctrl: bcm2835: Fix some merge fallout
gpio: Fix undefined lock_dep_class
gpio: Automatically add lockdep keys
gpio: Introduce struct gpio_irq_chip.first
gpio: Disambiguate struct gpio_irq_chip.nested
gpio: Add Tegra186 support
gpio: Export gpiochip_irq_{map,unmap}()
gpio: Implement tighter IRQ chip integration
gpio: Move lock_key into struct gpio_irq_chip
gpio: Move irq_valid_mask into struct gpio_irq_chip
gpio: Move irq_nested into struct gpio_irq_chip
gpio: Move irq_chained_parent to struct gpio_irq_chip
gpio: Move irq_default_type to struct gpio_irq_chip
gpio: Move irq_handler to struct gpio_irq_chip
gpio: Move irqdomain into struct gpio_irq_chip
gpio: Move irqchip into struct gpio_irq_chip
gpio: Introduce struct gpio_irq_chip
pinctrl: armada-37xx: remove unused variable
...
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pinctrl_request_gpio() and pinctrl_free_gpio() break the nice
namespacing in the other cross-calls like pinctrl_gpio_foo().
Just rename them and all references so we have one namespace
with all cross-calls under pinctrl_gpio_*().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
None of the Kconfigs for any of these drivers are tristate,
meaning that they currently are not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the drivers there is no doubt they are builtin-only. All
drivers get the exact same change, so they are handled in batch.
Changes are (1) use init.h header in place of module.h header,
(2) delete module_exit related code, (3) delete MODULE_DEVICE_TABLE,
and (4) delete MODULE_LICENCE/MODULE_AUTHOR and associated tags.
None of these drivers were using module_init() so we don't have to
worry about the init ordering getting changed with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE etc. tags since all that information
is already contained at the top of each file in the comments.
Cc: spear-devel@list.st.com
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better reflect
the fact that this is not the GPIO struct device abstraction. We will
add that soon so this would be totallt confusing.
- It was noted that the driver .get_value() callbacks was
sometimes reporting negative -ERR values to the gpiolib core, expecting
them to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than zero"
to indicate that a line was active. As some would have bit 31 set to
indicate "line active" it clashed with negative error codes. This is
fixed by the largeish series clamping values in all drivers with
!!value to [0,1] and then augmenting the code to propagate error codes
to consumers. (Includes some ACKed patches in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of() design
pattern is indeed very nice, but we want to reform the struct gpio_chip
to be a non-volative, stateless business, and keep states internal to
the gpiolib to be able to hold on to the state when adding a proper
userspace ABI (character device) further down the road. To achieve this,
drivers need a handle at the internal state that is not dependent on
their struct gpio_chip() so we add gpiochip_add_data() and
gpiochip_get_data() following the pattern of many other subsystems.
All the "use gpiochip data pointer" patches transforms drivers to this
scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that removed.
Instead of having a separate mm_gpio_chip struct for these generic
drivers, merge that into struct gpio_chip, simplifying the code and
removing the need for separate and confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from the
OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but
the branch is merged here too to account for infrastructural changes).
- The sx150x driver now supports the sx1502.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=63rR
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for v4.5.
Notably there are big refactorings mostly by myself, aimed at getting
the gpio_chip into a shape that makes me believe I can proceed to
preserve state for a proper userspace ABI (character device) that has
already been proposed once, but resulted in the feedback that I need
to go back and restructure stuff. So I've been restructuring stuff.
On the way I ran into brokenness (return code from the get_value()
callback) and had to fix it. Also, refactored generic GPIO to be
simpler.
Some of that is still waiting to trickle down from the subsystems all
over the kernel that provide random gpio_chips, I've touched every
single GPIO driver in the kernel now, oh man I didn't know I was
responsible for so much...
Apart from that we're churning along as usual.
I took some effort to test and retest so it should merge nicely and we
shook out a couple of bugs in -next.
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better
reflect the fact that this is not the GPIO struct device
abstraction. We will add that soon so this would be totallt
confusing.
- It was noted that the driver .get_value() callbacks was sometimes
reporting negative -ERR values to the gpiolib core, expecting them
to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than
zero" to indicate that a line was active. As some would have bit
31 set to indicate "line active" it clashed with negative error
codes. This is fixed by the largeish series clamping values in all
drivers with !!value to [0,1] and then augmenting the code to
propagate error codes to consumers. (Includes some ACKed patches
in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of()
design pattern is indeed very nice, but we want to reform the
struct gpio_chip to be a non-volative, stateless business, and keep
states internal to the gpiolib to be able to hold on to the state
when adding a proper userspace ABI (character device) further down
the road. To achieve this, drivers need a handle at the internal
state that is not dependent on their struct gpio_chip() so we add
gpiochip_add_data() and gpiochip_get_data() following the pattern
of many other subsystems. All the "use gpiochip data pointer"
patches transforms drivers to this scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that
removed. Instead of having a separate mm_gpio_chip struct for
these generic drivers, merge that into struct gpio_chip,
simplifying the code and removing the need for separate and
confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from
the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
but the branch is merged here too to account for infrastructural
changes).
- The sx150x driver now supports the sx1502"
* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
gpio: generic: make bgpio_pdata always visible
gpiolib: fix chip order in gpio list
gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
gpio: brcmstb: Allow building driver for BMIPS_GENERIC
gpio: brcmstb: Set endian flags for big-endian MIPS
gpio: moxart: fix build regression
gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
leds: pca9532: use gpiochip data pointer
leds: tca6507: use gpiochip data pointer
hid: cp2112: use gpiochip data pointer
bcma: gpio: use gpiochip data pointer
avr32: gpio: use gpiochip data pointer
video: fbdev: via: use gpiochip data pointer
gpio: pch: Optimize pch_gpio_get()
Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
pinctrl: nsp-gpio: use gpiochip data pointer
pinctrl: vt8500-wmt: use gpiochip data pointer
pinctrl: exynos5440: use gpiochip data pointer
pinctrl: at91-pio4: use gpiochip data pointer
...
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: spear-devel@list.st.com
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
CONFIG_PINCTRL_SPEAR is more suitable than CONFIG_PLAT_SPEAR
to guard the drivers/pinctrl/spear/ directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.
This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:
@@
struct gpio_chip *var;
@@
-var->dev
+var->parent
and:
@@
struct gpio_chip var;
@@
-var.dev
+var.parent
and:
@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent
Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.
This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Switch to my kernel.org alias instead of a badly named gmail address,
which I rarely use.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, pinctrl_register() just returns NULL on error, so the
callers can not know the exact reason of the failure.
Some of the pinctrl drivers return -EINVAL, some -ENODEV, and some
-ENOMEM on error of pinctrl_register(), although the error code
might be different from the real cause of the error.
This commit reworks pinctrl_register() to return the appropriate
error code and modifies all of the pinctrl drivers to use IS_ERR()
for the error checking and PTR_ERR() for getting the error code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Ray Jui <rjui@broadcom.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Acked-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
This patch fix company name's spelling typo in module descriptions
and a Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Chris Snook <chris.snook@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
commit 2243a87d90
"pinctrl: avoid duplicated calling enable_pinmux_setting for a pin"
removed the .disable callback from the struct pinmux_ops,
making the .enable() callback the only remaining callback.
However .enable() is a bad name as it seems to imply that a
muxing can also be disabled. Rename the callback to .set_mux()
and also take this opportunity to clean out any remaining
mentions of .disable() from the documentation.
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Fan Wu <fwu@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make of_device_id array const, because all OF functions handle it as
const.
Signed-off-by: Kiran Padwal <kiran.padwal21@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
What the patch does:
1. Call pinmux_disable_setting ahead of pinmux_enable_setting
each time pinctrl_select_state is called
2. Remove the HW disable operation in pinmux_disable_setting function.
3. Remove the disable ops in struct pinmux_ops
4. Remove all the disable ops users in current code base.
Notes:
1. Great thanks for the suggestion from Linus, Tony Lindgren and
Stephen Warren and Everyone that shared comments on this patch.
2. The patch also includes comment fixes from Stephen Warren.
The reason why we do this:
1. To avoid duplicated calling of the enable_setting operation
without disabling operation inbetween which will let the pin
descriptor desc->mux_usecount increase monotonously.
2. The HW pin disable operation is not useful for any of the
existing platforms.
And this can be used to avoid the HW glitch after using the
item #1 modification.
In the following case, the issue can be reproduced:
1. There is a driver that need to switch pin state dynamically,
e.g. between "sleep" and "default" state
2. The pin setting configuration in a DTS node may be like this:
component a {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&a_grp_setting &c_grp_setting>;
pinctrl-1 = <&b_grp_setting &c_grp_setting>;
}
The "c_grp_setting" config node is totally identical, maybe like
following one:
c_grp_setting: c_grp_setting {
pinctrl-single,pins = <GPIO48 AF6>;
}
3. When switching the pin state in the following official pinctrl
sequence:
pin = pinctrl_get();
state = pinctrl_lookup_state(wanted_state);
pinctrl_select_state(state);
pinctrl_put();
Test Result:
1. The switch is completed as expected, that is: the device's
pin configuration is changed according to the description in the
"wanted_state" group setting
2. The "desc->mux_usecount" of the corresponding pins in "c_group"
is increased without being decreased, because the "desc" is for
each physical pin while the setting is for each setting node
in the DTS.
Thus, if the "c_grp_setting" in pinctrl-0 is not disabled ahead
of enabling "c_grp_setting" in pinctrl-1, the desc->mux_usecount
will keep increasing without any chance to be decreased.
According to the comments in the original code, only the setting,
in old state but not in new state, will be "disabled" (calling
pinmux_disable_setting), which is correct logic but not intact. We
still need consider case that the setting is in both old state
and new state. We can do this in the following two ways:
1. Avoid to "enable"(calling pinmux_enable_setting) the "same pin
setting" repeatedly
2. "Disable"(calling pinmux_disable_setting) the "same pin setting",
actually two setting instances, ahead of enabling them.
Analysis:
1. The solution #2 is better because it can avoid too much
iteration.
2. If we disable all of the settings in the old state and one of
the setting(s) exist in the new state, the pins mux function
change may happen when some SoC vendors defined the
"pinctrl-single,function-off"
in their DTS file.
old_setting => disabled_setting => new_setting.
3. In the pinmux framework, when a pin state is switched, the
setting in the old state should be marked as "disabled".
Conclusion:
1. To Remove the HW disabling operation to above the glitch mentioned
above.
2. Handle the issue mentioned above by disabling all of the settings
in old state and then enable the all of the settings in new state.
Signed-off-by: Fan Wu <fwu@marvell.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the SPEAr PLGPIO driver over to using the irqchip
helpers.
As part of this effort, also get rid of the strange irq_base
calculation and failure to use d->hwirq for obtaining a local
irqchip offset.
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Cc: spear-devel@list.st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The symbol SPEAr310_pinctrl_of_match does not exist at all. Fix it.
We didn't hit the compile error because this driver can only be built-in now.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
'spear310_o2p' is referenced only in this file.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- A quite apparent mutex fix in an untested codepath
- A compile warning fix in the plgpio driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=kX7M
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-fixes-v3.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"Two fixes to the pinctrl subsystem for v3.10:
- A quite apparent mutex fix in an untested codepath
- A compile warning fix in the plgpio driver"
* tag 'pinctrl-fixes-v3.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: fix mutex deadlock in get_pinctrl_dev_from_of_node()
pinctrl: plgpio: add CONFIG_PM_SLEEP to suspend/resume functions
Here is a collection of cleanup patches. Among the pieces that stand out are:
- The deletion of h720x platforms
- Split of at91 non-dt platforms to their own Kconfig file to keep them separate
- General cleanups and refactoring of i.MX and MXS platforms
- Some restructuring of clock tables for OMAP
- Convertion of PMC driver for Tegra to dt-only
- Some renames of sunxi -> sun4i (Allwinner A10)
- ... plus a bunch of other stuff that I haven't mentioned
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=xCAx
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanup from Olof Johansson:
"Here is a collection of cleanup patches. Among the pieces that stand
out are:
- The deletion of h720x platforms
- Split of at91 non-dt platforms to their own Kconfig file to keep
them separate
- General cleanups and refactoring of i.MX and MXS platforms
- Some restructuring of clock tables for OMAP
- Convertion of PMC driver for Tegra to dt-only
- Some renames of sunxi -> sun4i (Allwinner A10)
- ... plus a bunch of other stuff that I haven't mentioned"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (119 commits)
ARM: i.MX: remove unused ARCH_* configs
ARM i.MX53: remove platform ahci support
ARM: sunxi: Rework the restart code
irqchip: sunxi: Rename sunxi to sun4i
irqchip: sunxi: Make use of the IRQCHIP_DECLARE macro
clocksource: sunxi: Rename sunxi to sun4i
clocksource: sunxi: make use of CLKSRC_OF
clocksource: sunxi: Cleanup the timer code
ARM: at91: remove trailing semicolon from macros
ARM: at91/setup: fix trivial typos
ARM: EXYNOS: remove "config EXYNOS_DEV_DRM"
ARM: EXYNOS: change the name of USB ohci header
ARM: SAMSUNG: Remove unnecessary code for dma
ARM: S3C24XX: Remove unused GPIO drive strength register definitions
ARM: OMAP4+: PM: Restore CPU power state to ON with clockdomain force wakeup method
ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2412
ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2410
ARM: S3C24XX: Removed unneeded dependency on ARCH_S3C24XX for boards
ARM: SAMSUNG: Fix typo "CONFIG_SAMSUNG_DEV_RTC"
ARM: S5P64X0: Fix typo "CONFIG_S5P64X0_SETUP_SDHCI"
...
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/pinctrl/spear/pinctrl-plgpio.c:645:12: warning: 'plgpio_suspend' defined but not used [-Wunused-function]
drivers/pinctrl/spear/pinctrl-plgpio.c:684:12: warning: 'plgpio_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These functions have been introduced by commit 10a8c383 (irq: introduce
entry and exit functions for chained handlers) in asm/mach/irq.h. This
patch moves them to linux/irqchip/chained_irq.h so that generic irqchip
drivers do not rely on architecture specific header files.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
The pinconf, pinctrl and pinmux operation structures hold function
pointers that are never modified. Declare them as const.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Barry Song <baohua.song@csr.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This is
going to be a pain for the merge with different subsystem trees, I know,
but all of the patches included here have been ACKed by their various
subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them all,
it's up to you. The merges should all be trivial, and Stephen has been
doing them all in linux-next for a few weeks now quite easily.
Other than the __dev* marking removals, there's nothing major here, some
firmware loading updates and other minor things in the driver core.
All of these have (much to Stephen's annoyance), been in linux-next for
a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHkPkACgkQMUfUDdst+ykaWgCfW7AM30cv0nzoVO08ax6KjlG1
KVYAn3z/KYazvp4B6LMvrW9y0G34Wmad
=yvVr
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This
is going to be a pain for the merge with different subsystem trees, I
know, but all of the patches included here have been ACKed by their
various subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them
all, it's up to you. The merges should all be trivial, and Stephen
has been doing them all in linux-next for a few weeks now quite
easily.
Other than the __dev* marking removals, there's nothing major here,
some firmware loading updates and other minor things in the driver
core.
All of these have (much to Stephen's annoyance), been in linux-next
for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up trivial conflicts in drivers/gpio/gpio-{em,stmpe}.c due to gpio
update.
* tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (93 commits)
modpost.c: Stop checking __dev* section mismatches
init.h: Remove __dev* sections from the kernel
acpi: remove use of __devinit
PCI: Remove __dev* markings
PCI: Always build setup-bus when PCI is enabled
PCI: Move pci_uevent into pci-driver.c
PCI: Remove CONFIG_HOTPLUG ifdefs
unicore32/PCI: Remove CONFIG_HOTPLUG ifdefs
sh/PCI: Remove CONFIG_HOTPLUG ifdefs
powerpc/PCI: Remove CONFIG_HOTPLUG ifdefs
mips/PCI: Remove CONFIG_HOTPLUG ifdefs
microblaze/PCI: Remove CONFIG_HOTPLUG ifdefs
dma: remove use of __devinit
dma: remove use of __devexit_p
firewire: remove use of __devinitdata
firewire: remove use of __devinit
leds: remove use of __devexit
leds: remove use of __devinit
leds: remove use of __devexit_p
mmc: remove use of __devexit
...
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinitdata is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SPEAr SoC's don't do anything in clk_prepare() of plgpio driver,
so there is no need to call this routine multiple times. Just
call it once at probe.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver allows clk_get() failure, and still work without it.
This patch adds !IS_ERR(plgpio->clk) checking in plgpio_request() error path
so we only call clk_disable_unprepare() if clk_prepare_enable() is called.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently get_gpio_pingroup() may return NULL or ERR_PTR(-EINVAL) when
no gpio_pingroup found. The caller in gpio_request_endisable() only
checks if the return value is NULL. Return ERR_PTR(-EINVAL) for
get_gpio_pingroup() causes problem and seems not necessary.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current code does not work if count > 1, fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
