The timing values for dw-dsi are often dependent on the used display and
according to Philippe Cornu will most likely also depend on the used phy
technology in the soc-specific implementation.
To solve this and allow specific implementations to define them as needed
add a new get_timing callback to phy_ops and call this from the dphy_timing
function to retrieve the necessary values for the specific mode.
Right now this handles the hs2lp + lp2hs where Rockchip SoCs need handling
according to the phy speed, while STM seems to be ok with static values.
changes in v5:
- rebase on 5.5-rc1
- merge into px30 dsi series to prevent ordering conflicts
changes in v4:
- rebase to make it directly fit on top of drm-misc-next after all
changes in v3:
- check existence of phy_ops->get_timing in __dw_mipi_dsi_probe()
- emit actual error when get_timing() call fails
- add tags from Philippe and Yannick
changes in v2:
- add driver-specific handling, don't force all bridge users to use
the same timings, as suggested by Philippe
Suggested-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Yannick Fertre <yannick.fertre@st.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191209143130.4553-2-heiko@sntech.de
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl0Gj1MeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGctkH/0At3+SQPY2JJSy8
i6+TDeytFx9OggeGLPHChRfehkAlvMb/kd34QHnuEvDqUuCAMU6HZQJFKoK9mvFI
sDJVayPGDSqpm+iv8qLpMBPShiCXYVnGZeVfOdv36jUswL0k6wHV1pz4avFkDeZa
1F4pmI6O2XRkNTYQawbUaFkAngWUCBG9ECLnHJnuIY6ohShBvjI4+E2JUaht+8gO
M2h2b9ieddWmjxV3LTKgsK1v+347RljxdZTWnJ62SCDSEVZvsgSA9W2wnebVhBkJ
drSmrFLxNiM+W45mkbUFmQixRSmjv++oRR096fxAnodBxMw0TDxE1RiMQWE6rVvG
N6MC6xA=
=+B0P
-----END PGP SIGNATURE-----
Merge v5.2-rc5 into drm-next
Maarten needs -rc4 backmerged so he can pull in the fbcon notifier
removal topic branch into drm-misc-next.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add power on & off optional physical operation functions, helpful to
program specific registers of the DSI physical part.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1558952499-15418-2-git-send-email-yannick.fertre@st.com
Based on 1 normalized pattern(s):
license terms gnu general public license gpl version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.447718015@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To allow users to include dw_mipi_dsi.h without pulling in dependencies
make dw_mipi_dsi.h self-contained.
Use forward declarations when possible.
v2:
- Drop forward declarations of local structs (Laurent)
- Add include of drm_modes.h (Laurent)
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190519183636.19588-2-sam@ravnborg.org
The mode and ajusted_mode passed to the bridge .mode_set() operation
should never be modified by the bridge (and are not in any of the
existing bridge drivers). Make them const to make this clear.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Allow to also drive a slave dw-mipi-dsi controller in a dual-dsi
setup. This will require additional implementation-specific
code to look up the slave instance and do specific setup.
Also will probably need code in the specific crtcs as dual-dsi
does not equal two separate dsi outputs.
To activate, the implementation-specific code should set the slave
using dw_mipi_dsi_set_slave() before calling __dw_mipi_dsi_bind().
v2:
- expect real interface number of lanes
- keep links to both master and slave
v3:
- remove unneeded separate variables
- remove unneeded second slave settings
- disable slave before master
- lane-sum calculation comments
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-7-heiko@sntech.de
With the regular means of adding the dsi-component in probe it creates
a race condition with the panel probing, as the panel device only gets
created after the dsi-bus got created.
When the panel-driver is build as a module it currently fails hard as the
panel cannot be probed directly:
dw_mipi_dsi_bind()
__dw_mipi_dsi_probe()
creates dsi bus
creates panel device
triggers panel module load
panel not probed (module not loaded or panel probe slow)
drm_bridge_attach
fails with -EINVAL due to empty panel_bridge
Additionally the panel probing can run concurrently with dsi bringup
making it possible that the panel can already be found but dsi-attach
hasn't finished running.
To solve that cleanly we may want to only create the component after
the panel has finished probing, by calling component_add from the
host-attach dsi callback.
As that is specific to glue drivers, add a new struct for host_ops
so that glue drivers can tell the bridge to call specific functions
after the common host-attach and before the common host-detach run.
Suggested-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-4-heiko@sntech.de
__dw_mipi_dsi_probe() does all the grabbing of resources and does it using
devm-helpers. So this is happening on each try of master bringup possibly
slowing down things a lot.
Drivers using the component framework may instead want to call
dw_mipi_dsi_probe separately in their probe function to setup resources
early. That way the dsi bus also gets created earlier and also not
recreated on each bind-try, so that attached panels can load their modules
and be probed way before the bridge-attach in the bind call.
So drop the call to __dw_mipi_dsi_probe and modify the function to take
a struct dw_mipi_dsi instead of the platform-device.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-3-heiko@sntech.de
Bridge drivers/helpers shouldn't be clobbering the drvdata, since a
parent driver might need to own this. Instead, let's return our
'dw_mipi_dsi' object and have callers pass that back to us for removal.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Acked-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171128010538.119114-1-briannorris@chromium.org
