Devices should also operate normally when runtime PM is not enabled.
In case runtime PM is disabled activate the device already in probe().
Any related power domain needs to be then left permanently in active
state by the platform.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This define is only used in s5pcsis_irq_handler():
if ((status & S5PCSIS_INTSRC_NON_IMAGE_DATA) && pktbuf->data) {
The problem is that "status" is a 32 bit and (0xff << 28) is larger than
32 bits and that sets off a static checker warning. I consulted with
Sylwester Nawrocki and the define should actually be (0xf << 28).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the generic PHY API instead of the platform callback
to control the MIPI CSIS DPHY.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add compatible property for the Exynos5250 and enable the frame start
and frame end interrupts. These interrupts are needed for the Exynos5
FIMC-IS firmware. The driver enables those interrupt only where available,
depending on the 'compatible' property. This can be optimized further,
by exposing some API at the subdev driver, so the host driver can enable
extra interrupts only for the image processing chains involving FIMC-IS.
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When 'node' is NULL, the print statement tries to dereference it.
Hence replace the variable with the one that is accessible.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure TRY format is propagated from the sink to source pad.
The format at both pads is always same so the TRY format buffer
for pad 0 is used to hold format for both pads.
While at it remove redundant fmt->pad checking.
Reported-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The s5p-fimc directory now contains drivers for multiple IP blocks
found in multiple Samsung application processors. This includes FIMC
(CAMIF), MIPI CSIS and FIMC LITE. FIMC-IS (Imaging Subsystem) driver
is going to be put into same directory. Hence we rename it to
exynos4-is as s5p-fimc was only relevant for early version of this
driver, when it only supported FIMC IP block.
The imaging subsystem drivers for Exynos4 SoC series and S5PV210 will
be included in drivers/media/platform/exynos4-is directory, with some
modules shared with exynos5 series, while the rest of exynos5 specific
modules will find their home in drivers/media/platform/exynos5-is.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
