* Handle CM_SIDR_REQ_ATTR_ID and CM_SIDR_REP_ATTR_ID
in multiplex_cm_handler and demux_cm_handler.
* Handle Service ID Resolution messages and REQ messages
separately, for their formats are different.
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there is no connection between the MAC/VLAN and the GID
when using IP-based addressing, the proxy QP1 (running on the
slave) must pass the source-mac, destination-mac, and vlan_id
information separately from the GID. Additionally, the Host
must pass the remote source-mac and vlan_id back to the slave,
This is achieved as follows:
Outgoing MADs:
1. Source MAC: obtained from the CQ completion structure
(struct ib_wc, smac field).
2. Destination MAC: obtained from the tunnel header
3. vlan_id: obtained from the tunnel header.
Incoming MADs
1. The source (i.e., remote) MAC and vlan_id are passed in
the tunnel header to the proxy QP1.
VST mode support:
For outgoing MADs, the vlan_id obtained from the header is
discarded, and the vlan_id specified by the Hypervisor is used
instead.
For incoming MADs, the incoming vlan_id (in the wc) is discarded, and the
"invalid" vlan (0xffff) is substituted when forwarding to the slave.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IB side of RoCE requires the MAC table index of the
MAC address used by its QPs.
To obtain the real MAC index, the IB side registers the
MAC (increasing its ref count, and also returning the
real MAC index) during the modify-qp sequence.
This protects against the ETH side deleting or modifying
that MAC table entry while the QP is active.
Note that until the modify-qp command returns success,
the MAC and VLAN information only has "candidate" status.
If the modify-qp succeeds, the "candidate" info is promoted
to the operational MAC/VLAN info for the qp. If the modify fails,
the candidate MAC/VLAN is unregistered, and the old qp info
is preserved.
The patch is a bit complex, because there are multiple qp
transitions where the primary-path information may be
modified: INIT-to-RTR, and SQD-to-SQD.
Similarly for the alternate path information.
Therefore the code must handle cases where path information
has already been entered into the QP context by previous
qp transitions.
For the MAC address, the success logic is as follows:
1. If there was no previous MAC, simply move the candidate
MAC information to the operational information, and reset
the candidate MAC info.
2. If there was a previous MAC, unregister it. Then move
the MAC information from candidate to operational, and
reset the candidate info (as in 1. above).
The MAC address failure logic is the same for all cases:
- Unregister the candidate MAC, and reset the candidate MAC info.
For Vlan registration, the logic is similar.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GIDs are statically distributed, as follows:
PF: gets 16 GIDs
VFs: Remaining GIDS are divided evenly between VFs activated by the driver.
If the division is not even, lower-numbered VFs get an extra GID.
For an IB interface, the number of gids per guest remains as before: one gid per guest.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This requires the following modifications:
1. Fix build_mlx4_header to properly fill in the ETH fields
2. Adjust mux and demux QP1 flow to support RoCE.
This commit still assumes only one GID per slave for RoCE.
The commit enabling multiple GIDs is a subsequent commit, and
is done separately because of its complexity.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull SCSI target fixes from Nicholas Bellinger:
"Mostly minor fixes this time to v3.14-rc1 related changes. Also
included is one fix for a free after use regression in persistent
reservations UNREGISTER logic that is CC'ed to >= v3.11.y stable"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
Target/sbc: Fix protection copy routine
IB/srpt: replace strict_strtoul() with kstrtoul()
target: Simplify command completion by removing CMD_T_FAILED flag
iser-target: Fix leak on failure in isert_conn_create_fastreg_pool
iscsi-target: Fix SNACK Type 1 + BegRun=0 handling
target: Fix missing length check in spc_emulate_evpd_83()
qla2xxx: Remove last vestiges of qla_tgt_cmd.cmd_list
target: Fix 32-bit + CONFIG_LBDAF=n link error w/ sector_div
target: Fix free-after-use regression in PR unregister
We should use rdma_vlan_dev_real_dev() instead of using vlan_dev_real_dev()
when building the GID table for a vlan interface.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use correct value for obtaining traffic class from device
response for Query QP request.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We use "tx_desc" again after we free it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix a possible NULL pointer dereference in disconnection flow. This
can happen if the target disconnected/rejected the connection request,
e.g before the binding stage between iscsi connection to the transport
connection.
Signed-off-by: Alex Tabachnik <alext@mellanox.com>
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Error reported at http://marc.info/?l=linux-rdma&m=138995755801039&w=2
Fix short to int cast for big endian systems.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Remove Kconfig dependency of mlx5_ib/mlx5_core on X86, since there is
no such dependency in reality.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Research has shown that commit a77fcf8950 ("IB/qib: Use a single
txselect module parameter for serdes tuning") missed a key serdes init
sequence.
This patch add that sequence.
Cc: <stable@vger.kernel.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
For userspace RoCE UD QPs we need to know the GID format that the
kernel uses, e.g when working over older kernels. For that end, add a
new port capability IB_PORT_IP_BASED_GIDS and report it when query
port is issued.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When scanning netdevices we need to check a few more conditions and
cases to build the IBoE GID table properly. For example, under
bonding we must make sure that when a port is down, the bond IP
address isn't programmed as a GID, since doing so will cause failure
with IB core flows that selects ports by GID.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The IBoE code used to reset the GID table did it for all Ethernet
ports of the device. Since the whole architecture of generating GIDs
and responding to events is port-based, this is inefficient and can
lead to wrong content in the GID table. Change the reset flow to be
per-port.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Updating the GID table under IBoE requires read/write from/to shared
data structures. These data structures are protected with the device
iboe lock. The flows that modify the GID table start from
1. Initializing the GID table
2. NETDEV events
3. INET or INET6 events
This patch makes sure that the flow of initializing the GID table is
consistent with the other two flows w.r.t on what step the lock is taken.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
On the one hand, the invocation of netdev_master_upper_dev_get()
within mlx4_ib_scan_netdevs() must be done with rtnl lock held. On
the other hand, it's wrong to call rtnl_lock() from within this
function since it's also called by our netdev notifier callback.
Therefore move the locking to mlx4_ib_add() so that both cases are
covered.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Make sure that for Ethernet ports, the port GID table index 0 is always
occupied with a default GID of the relevant IPv6 link-local adderss.
This provides better user experience for legacy applications that don't use
the RDMA CM and were working on index 0 prior to the IP addressing change.
Also, as GIDs are generated from IP addresses of the network devices that
are associated with the port, it's basically possible that the GID table
will be empty if no IP address was assigned. This doesn't comply with the
IB spec section 4.1.1 "GID usage and properties".
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When the device has only Ethernet ports, don't try to allocate range
of steerable UD QPs since they aren't needed. This fixes an issue
where mlx4 VFs tried to allocate a range of UD steerable QPs, but
failed to do so.
Fixes: c1c9850112 ("IB/mlx4: Add support for steerable IB UD QPs")
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Set the return variable to an error code as done elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Set the return variable to an error code as done elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Currently Connect-IB does not support blocking multicast loopback, so
don't set IB_DEVICE_BLOCK_MULTICAST_LOOPBACK in the device caps.
Reported by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit c1be5232d2 ("Fix micro UAR allocator") broke binary compatibility
between libmlx5 and mlx5_ib since it defines a different value to the number
of micro UARs per page, leading to wrong calculation in libmlx5. This patch
defines struct mlx5_ib_alloc_ucontext_req_v2 as an extension to struct
mlx5_ib_alloc_ucontext_req. The extended size is determined in mlx5_ib_alloc_ucontext()
and in case of old library we use uuarn 0 which works fine -- this is
acheived due to create_user_qp() falling back from high to medium then to
low class where low class will return 0. For new libraries we use the
more sophisticated allocation algorithm.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix the RC QPs send queue overhead computation to take into account
two additional segments in the WQE which are needed for registration
operations.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- add support for SCSI Referrals (Hannes)
- add support for T10 DIF into target core (nab + mkp)
- add support for T10 DIF emulation in FILEIO + RAMDISK backends (Sagi + nab)
- add support for T10 DIF -> bio_integrity passthrough in IBLOCK backend (nab)
- prep changes to iser-target for >= v3.15 T10 DIF support (Sagi)
- add support for qla2xxx N_Port ID Virtualization - NPIV (Saurav + Quinn)
- allow percpu_ida_alloc() to receive task state bitmask (Kent)
- fix >= v3.12 iscsi-target session reset hung task regression (nab)
- fix >= v3.13 percpu_ref se_lun->lun_ref_active race (nab)
- fix a long-standing network portal creation race (Andy)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (51 commits)
target: Fix percpu_ref_put race in transport_lun_remove_cmd
target/iscsi: Fix network portal creation race
target: Report bad sector in sense data for DIF errors
iscsi-target: Convert gfp_t parameter to task state bitmask
iscsi-target: Fix connection reset hang with percpu_ida_alloc
percpu_ida: Make percpu_ida_alloc + callers accept task state bitmask
iscsi-target: Pre-allocate more tags to avoid ack starvation
qla2xxx: Configure NPIV fc_vport via tcm_qla2xxx_npiv_make_lport
qla2xxx: Enhancements to enable NPIV support for QLOGIC ISPs with TCM/LIO.
qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
IB/isert: pass scatterlist instead of cmd to fast_reg_mr routine
IB/isert: Move fastreg descriptor creation to a function
IB/isert: Avoid frwr notation, user fastreg
IB/isert: seperate connection protection domains and dma MRs
tcm_loop: Enable DIF/DIX modes in SCSI host LLD
target/rd: Add DIF protection into rd_execute_rw
target/rd: Add support for protection SGL setup + release
target/rd: Refactor rd_build_device_space + rd_release_device_space
target/file: Add DIF protection support to fd_execute_rw
target/file: Add DIF protection init/format support
...
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
This patch propigates the use of task state bitmask now used by
percpu_ida_alloc() up the iscsi-target callchain, replacing the
use of GFP_ATOMIC for TASK_RUNNING, and GFP_KERNEL for
TASK_INTERRUPTIBLE.
Also, drop the unnecessary gfp_t parameter to isert_allocate_cmd(),
and just pass TASK_INTERRUPTIBLE into iscsit_allocate_cmd().
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Verify that reserved fields in struct mlx5_ib_resize_cq are cleared
before continuing execution of the verb. This is required to allow
making use of this area in future revisions.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The current code attmepts to call ib_umem_get() even if the length is
zero, which causes a failure. Since the spec allows zero length work
queues, change the code so we don't call ib_umem_get() in those cases.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Implement resize CQ which is a mandatory verb in mlx5.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Modify CQ is used by ULPs like IPoIB to change moderation parameters. This
patch adds support in mlx5.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Put a wmb() to make sure the doorbell record is visible to the HCA before we
hit doorbell.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use the possibly more efficient ether_addr_equal() instead of memcmp().
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The GSI QP type is compatible with and should be allowed to send data
to/from any UD QP. This was found when testing ibacm on the same node
as an SA.
Cc: <stable@vger.kernel.org>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Building mem.o for 32 bits x86 triggers a GCC warning:
drivers/infiniband/hw/cxgb4/mem.c: In function '_c4iw_write_mem_dma_aligned':
drivers/infiniband/hw/cxgb4/mem.c:79:25: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Silence that warning by casting "&wr_wait" to unsigned long before
casting it to __be64. That's what _c4iw_write_mem_inline() already does.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There is a path in handle_vq() where kmem_cache_free() can be called
with pointer to a local variable. It can happen if vq_repbuf_alloc()
failed to allocate memory from cache and req is NULL.
The patch adds check if cache memory was allocated before freeing it.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Svetlana Mavrina <another.karnil@gmail.com>
Reviewed-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Roland Dreier <roland@purestorage.com>
After booting without a working link, "ip link" shows:
5: mlx4_ib1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 2044 qdisc pfifo_fast
state DOWN qlen 256
...
7: mlx4_ib1.8003@mlx4_ib1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 2044 qdisc
pfifo_fast state DOWN qlen 256
...
Then after connecting and disconnecting the link, which should result
in exactly the same state as before, it shows:
5: mlx4_ib1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 2044 qdisc pfifo_fast
state DOWN qlen 256
...
7: mlx4_ib1.8003@mlx4_ib1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 2044 qdisc
pfifo_fast state LOWERLAYERDOWN qlen 256
...
Notice the (now correct) LOWERLAYERDOWN operstate shown for the
mlx4_ib1.8003 interface. Ideally the identical state would be shown
right after boot.
The problem is related to the calling of netif_carrier_off() in
network drivers. For a long time it was known that doing
netif_carrier_off() before registering the netdevice would result in
the interface's operstate being shown as UNKNOWN if the device was
brought up without a working link. This problem was fixed in commit
8f4cccbbd9 ('net: Set device operstate at registration time'), but
still there remains the minor inconsistency demonstrated above.
This patch fixes it by moving ipoib's call to netif_carrier_off() into
the .ndo_open method, which is where network drivers ordinarily do it.
With the patch when doing the same test as above, the operstate of
mlx4_ib1.8003 is shown as LOWERLAYERDOWN right after boot.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix the below "make W=1" build warning:
drivers/infiniband/core/iwcm.c: In function ‘destroy_cm_id’:
drivers/infiniband/core/iwcm.c:330: warning: variable ‘ret’ set but not used
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If addr is not a linklocal address, the code incorrectly fails to
return and ends up assigning the scope ID to the scope id of the
address, which is wrong. Fix by checking if it's a link local address
first, and immediately return 0 if not.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This is called from qp_grp_and_vf_bind() and we are holding the
vf->lock so the allocation can't sleep.
Fixes: e3cf00d0a8 ('IB/usnic: Add Cisco VIC low-level hardware driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The rport timers must be stopped before the SRP initiator destroys the
resources associated with the SCSI host. This is necessary because
otherwise the callback functions invoked from the SRP transport layer
could trigger a use-after-free. Stopping the rport timers before
invoking scsi_remove_host() can trigger long delays in the SCSI error
handler if a transport layer failure occurs while scsi_remove_host()
is in progress. Hence move the code for stopping the rport timers from
srp_rport_release() into a new function and invoke that function after
scsi_remove_host() has finished. This patch fixes the following
sporadic kernel crash:
kernel BUG at include/asm-generic/dma-mapping-common.h:64!
invalid opcode: 0000 [#1] SMP
RIP: 0010:[<ffffffffa03b20b1>] [<ffffffffa03b20b1>] srp_unmap_data+0x121/0x130 [ib_srp]
Call Trace:
[<ffffffffa03b20fc>] srp_free_req+0x3c/0x80 [ib_srp]
[<ffffffffa03b2188>] srp_finish_req+0x48/0x70 [ib_srp]
[<ffffffffa03b21fb>] srp_terminate_io+0x4b/0x60 [ib_srp]
[<ffffffffa03a6fb5>] __rport_fail_io_fast+0x75/0x80 [scsi_transport_srp]
[<ffffffffa03a7438>] rport_fast_io_fail_timedout+0x88/0xc0 [scsi_transport_srp]
[<ffffffff8108b370>] worker_thread+0x170/0x2a0
[<ffffffff81090876>] kthread+0x96/0xa0
[<ffffffff8100c0ca>] child_rip+0xa/0x20
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
