when receive eem echo command, it will send a response,
but queue this response to the usb request which allocate
from gadget device endpoint zero,
and transmit the request to IN endpoint of eem interface.
on dwc3 gadget, it will trigger following warning in function
__dwc3_gadget_ep_queue(),
if (WARN(req->dep != dep, "request %pK belongs to '%s'\n",
&req->request, req->dep->name))
return -EINVAL;
fix it by allocating a usb request from IN endpoint of eem interface,
and transmit the usb request to same IN endpoint of eem interface.
Signed-off-by: Linyu Yuan <linyyuan@codeaurora.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210616115142.34075-1-linyyuan@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Running sparse checker it shows warning message about
incorrect endianness used for descriptor initialization:
| f_hid.c:91:43: warning: incorrect type in initializer (different base types)
| f_hid.c:91:43: expected restricted __le16 [usertype] bcdHID
| f_hid.c:91:43: got int
Fixing issue with cpu_to_le16() macro, however this is not a real issue
as the value is the same both endians.
Cc: Fabien Chouteau <fabien.chouteau@barco.com>
Cc: Segiy Stetsyuk <serg_stetsuk@ukr.net>
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Link: https://lore.kernel.org/r/20210617162755.29676-1-ruslan.bilovol@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter writes:
Some tiny improvements for cdns USB3 drivers, no important things.
* tag 'usb-v5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: cdns3: cdns3-gadget: Use list_move_tail instead of list_del/list_add_tail
doc: dt-binding: cdns,usb3: Add interrupt-names property under required
usb: cdnsp: Useless condition has been removed
usb: cdns3: Corrected comment to align with kernel-doc comment
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove broken task->state references and let wake_up_process() DTRT.
The anti-pattern in these patches breaks the ordering of ->state vs
COND as described in the comment near set_current_state() and can lead
to missed wakeups:
(OoO load, observes RUNNING)<-.
for (;;) { |
t->state = UNINTERRUPTIBLE; |
smp_mb(); ,-----> | (observes !COND)
| /
if (COND) ---------' | COND = 1;
break; `- if (t->state != RUNNING)
wake_up_process(t); // not done
schedule(); // forever waiting
}
t->state = TASK_RUNNING;
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Davidlohr Bueso <dbueso@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210611082838.160855222@infradead.org
when system is doing s4, the process of xhci_resume may be as below:
1、xhci_mem_cleanup
2、xhci_init->xhci_mem_init->xhci_mem_cleanup(when memory is not enough).
xhci_mem_cleanup will be executed twice when system is out of memory.
xhci->port_caps is freed in xhci_mem_cleanup,but it isn't set to NULL.
It will be freed twice when xhci_mem_cleanup is called the second time.
We got following bug when system resumes from s4:
kernel BUG at mm/slub.c:309!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
CPU: 0 PID: 5929 Tainted: G S W 5.4.96-arm64-desktop #1
pc : __slab_free+0x5c/0x424
lr : kfree+0x30c/0x32c
Call trace:
__slab_free+0x5c/0x424
kfree+0x30c/0x32c
xhci_mem_cleanup+0x394/0x3cc
xhci_mem_init+0x9ac/0x1070
xhci_init+0x8c/0x1d0
xhci_resume+0x1cc/0x5fc
xhci_plat_resume+0x64/0x70
platform_pm_thaw+0x28/0x60
dpm_run_callback+0x54/0x24c
device_resume+0xd0/0x200
async_resume+0x24/0x60
async_run_entry_fn+0x44/0x110
process_one_work+0x1f0/0x490
worker_thread+0x5c/0x450
kthread+0x158/0x160
ret_from_fork+0x10/0x24
Original patch that caused this issue was backported to 4.4 stable,
so this should be backported to 4.4 stabe as well.
Fixes: cf0ee7c60c ("xhci: Fix memory leak when caching protocol extended capability PSI tables - take 2")
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Jiantao Zhang <water.zhangjiantao@huawei.com>
Signed-off-by: Tao Xue <xuetao09@huawei.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210617150354.1512157-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Save a bit of power by not interrupting so often by default if
XHCI_AVOID_BEI quirk is set.
In normal cases the xhci driver will only generate an interrupt on the last
isochronous TRB of an URB. In a common UVC webcam usecase there are 32 TRBs
per URB.
if AVOID_BEI flag is set then xhci driver will force an interrupt every 8th
isoc TRB to make sure the event ring doesn't get too full.
This is however way too frequent in common single webcam use cases, causing
1000 interrupts/sec and thus poor powermanagement performance.
Instead start with interrupting every 32 isoc TRB, and halve it in case
event ring becomes half-full. Stop halving when reaching a rate of every
8th trb.
This is a one way solution. If interrupt rate is increased it will stay
high until driver is reloaded. The highest rate is the same as the old
default rate.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210617150354.1512157-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the voltage is being decreased in power negotiation, the Source will
set the power supply to operate at the new voltage level before sending
PS_RDY. Relax the threshold before sending Request Message so that it
will not race with Source which begins to adjust the voltage right after
it sends Accept Message (PPS) or tSrcTransition (25~35ms) after it sends
Accept Message (non-PPS).
The real threshold will be set after Sink receives PS_RDY Message.
Fixes: f321a02cae ("usb: typec: tcpm: Implement enabling Auto Discharge disconnect support")
Cc: stable <stable@vger.kernel.org>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210616090102.1897674-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Cypress CY7C65632 appears to have an issue with auto suspend and
detecting devices, not too dissimilar to the SMSC 5534B hub. It is
easiest to reproduce by connecting multiple mass storage devices to
the hub at the same time. On a Lenovo Yoga, around 1 in 3 attempts
result in the devices not being detected. It is however possible to
make them appear using lsusb -v.
Disabling autosuspend for this hub resolves the issue.
Fixes: 1208f9e1d7 ("USB: hub: Fix the broken detection of USB3 device in SMSC hub")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210614155524.2228800-1-andrew@lunn.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to some other CP210x device types, CP2108 has a number of GPIO
pins that can be exposed through gpiolib.
CP2108 has four serial interfaces but only one set of GPIO pins, which
is modelled as a single gpio chip and registered as a child of the first
interface.
CP2108 has 16 GPIOs so the width of the state variables needs to be
extended to 16 bits and this is also reflected in the control requests.
Like CP2104, CP2108 have GPIO pins with configurable alternate
functions and pins unavailable for GPIO use are determined and reported
to gpiolib at probe.
Signed-off-by: Pho Tran <pho.tran@silabs.com>
Co-developed-by: Tung Pham <tung.pham@silabs.com>
Signed-off-by: Tung Pham <tung.pham@silabs.com>
[ johan: rewrite gpio get() and set(); misc cleanups; amend commit
message ]
Link: https://lore.kernel.org/r/20210610132844.25495-1-johan@kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Peter writes:
One bug fix for USB charger detection at imx7d and imx8m series SoCs
* tag 'usb-v5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: chipidea: imx: Fix Battery Charger 1.2 CDP detection
i.MX8MM cannot detect certain CDP USB HUBs. usbmisc_imx.c driver is not
following CDP timing requirements defined by USB BC 1.2 specification
and section 3.2.4 Detection Timing CDP.
During Primary Detection the i.MX device should turn on VDP_SRC and
IDM_SINK for a minimum of 40ms (TVDPSRC_ON). After a time of TVDPSRC_ON,
the i.MX is allowed to check the status of the D- line. Current
implementation is waiting between 1ms and 2ms, and certain BC 1.2
complaint USB HUBs cannot be detected. Increase delay to 40ms allowing
enough time for primary detection.
During secondary detection the i.MX is required to disable VDP_SRC and
IDM_SNK, and enable VDM_SRC and IDP_SINK for at least 40ms (TVDMSRC_ON).
Current implementation is not disabling VDP_SRC and IDM_SNK, introduce
disable sequence in imx7d_charger_secondary_detection() function.
VDM_SRC and IDP_SINK should be enabled for at least 40ms (TVDMSRC_ON).
Increase delay allowing enough time for detection.
Cc: <stable@vger.kernel.org>
Fixes: 746f316b75 ("usb: chipidea: introduce imx7d USB charger detection")
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Jun Li <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20210614175013.495808-1-breno.lima@nxp.com
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Call onboard_hub_create/destroy_pdevs() from _probe()/_remove()
to create/destroy platform devices for onboard USB hubs that may
be connected to the root hub of the controller. These functions
are a NOP unless CONFIG_USB_ONBOARD_HUB=y/m.
Also add a field to struct xhci_hcd to keep track of the onboard hub
platform devices that are owned by the xHCI.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210609150159.v12.4.I7a3a7d9d2126c34079b1cab87aa0b2ec3030f9b7@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The main issue this driver addresses is that a USB hub needs to be
powered before it can be discovered. For discrete onboard hubs (an
example for such a hub is the Realtek RTS5411) this is often solved
by supplying the hub with an 'always-on' regulator, which is kind
of a hack. Some onboard hubs may require further initialization
steps, like changing the state of a GPIO or enabling a clock, which
requires even more hacks. This driver creates a platform device
representing the hub which performs the necessary initialization.
Currently it only supports switching on a single regulator, support
for multiple regulators or other actions can be added as needed.
Different initialization sequences can be supported based on the
compatible string.
Besides performing the initialization the driver can be configured
to power the hub off during system suspend. This can help to extend
battery life on battery powered devices which have no requirements
to keep the hub powered during suspend. The driver can also be
configured to leave the hub powered when a wakeup capable USB device
is connected when suspending, and power it off otherwise.
Technically the driver consists of two drivers, the platform driver
described above and a very thin USB driver that subclasses the
generic driver. The purpose of this driver is to provide the platform
driver with the USB devices corresponding to the hub(s) (a hub
controller may provide multiple 'logical' hubs, e.g. one to support
USB 2.0 and another for USB 3.x).
Note: the current series only supports hubs connected directly to
a root hub (through xhci-plat), support for other configurations
could be added if needed.
Co-developed-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210609150159.v12.2.I7c9a1f1d6ced41dd8310e8a03da666a32364e790@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The B_SESS_VLD_WAKEUP_EN bit 6 was added by a mistake in a previous
commit. This bit corresponds to B_SESS_END_WAKEUP_EN, which we don't use.
The B_VBUS_VLD_WAKEUP_EN doesn't exist at all and B_SESS_VLD_WAKEUP_EN
needs to be in place of it. We don't utilize B-sensors in the driver,
so it never was a problem, nevertheless let's correct the definition of
the bits.
Fixes: 35192007d2 ("usb: phy: tegra: Support waking up from a low power mode")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210613145936.9902-2-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices need an extra delay after losing VBUS, otherwise VBUS may
be detected as active at suspend time, preventing the PHY's suspension
by the VBUS detection sensor. This problem was found on Asus Transformer
TF700T (Tegra30) tablet device, where the USB PHY wakes up immediately
from suspend because VBUS sensor continues to detect VBUS as active after
disconnection. We need to poll the PHY's VBUS wakeup status until it's
deasserted before suspending PHY in order to fix this minor trouble.
Fixes: 35192007d2 ("usb: phy: tegra: Support waking up from a low power mode")
Reported-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210613145936.9902-1-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make data_bits what it really is. Assign proper bit counts to data_bits
instead of magic 0..3. There are two reasons:
1) it's clear what we store there, and
2) it will make the transition to tty_tty_get_char_size() in the next
patch easier.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210610090247.2593-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The devctl register on musb is the only way to get state information
on musb. The hardware can easily get confused because it tries to do
things on it's own automagically, and things like slow VBUS rise can
make things fail.
Let's make it easier to debug the ongoing state change issues that
keep popping up on regular basis and add tracing support.
With these changes we can easily trace musb state change events with:
echo 1 > /sys/kernel/debug/tracing/events/musb/musb_state/enable
cat /sys/kernel/debug/tracing/trace_pipe
echo 0 > /sys/kernel/debug/tracing/events/musb/musb_state/enable
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Andreas Kemnade <andreas@kemnade.info>
Cc: Bhushan Shah <bshah@kde.org>
Cc: Drew Fustini <drew@beagleboard.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210604080536.12185-2-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want the usb fixes in here as well, and this resolves some merge
issues with:
drivers/usb/dwc3/debugfs.c
drivers/usb/dwc3/gadget.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
