Data received during half-duplex transmission must be filtered.
If the target device responds quickly, emptying the FIFO at the end of
the transmission can erase not only the echo characters but also part of
the response message.
By keeping the receive interrupt enabled even during transmission, it
allows you to filter each echo character and only in a number equal to
those transmitted.
The issue was generated by a target device that started responding
240us later having received a request in communication at 115200bps.
Sometimes, some messages received by the target were missing some of the
first bytes.
Fixes: 3a13884abe ("tty/serial: omap: empty the RX FIFO at the end of half-duplex TX")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20210418094705.27014-1-dariobin@libero.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the uart_unlock_and_check_sysrq() helper to defer sysrq processing
until receive processing is done and the port lock has been released.
This allows cleaning up the console_write() implementation by not having
to work around the recursive sysrq case (by dropping locking completely)
and also makes the console code work with PREEMPT_RT by no longer
relying on local_irq_save().
Reviewed-by: Valentin Caron<valentin.caron@foss.st.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210416140557.25177-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DMA is enabled the receive handler runs in a threaded handler, but
the primary handler up until very recently neither disabled interrupts
in the device or used IRQF_ONESHOT. This would lead to a deadlock if an
interrupt comes in while the threaded receive handler is running under
the port lock.
Commit ad76768124 ("serial: stm32: fix a deadlock condition with
wakeup event") claimed to fix an unrelated deadlock, but unfortunately
also disabled interrupts in the threaded handler. While this prevents
the deadlock mentioned in the previous paragraph it also defeats the
purpose of using a threaded handler in the first place.
Fix this by making the interrupt one-shot and not disabling interrupts
in the threaded handler.
Note that (receive) DMA must not be used for a console port as the
threaded handler could be interrupted while holding the port lock,
something which could lead to a deadlock in case an interrupt handler
ends up calling printk.
Fixes: ad76768124 ("serial: stm32: fix a deadlock condition with wakeup event")
Fixes: 3489187204 ("serial: stm32: adding dma support")
Cc: stable@vger.kernel.org # 4.9
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Cc: Gerald Baeza <gerald.baeza@st.com>
Reviewed-by: Valentin Caron<valentin.caron@foss.st.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210416140557.25177-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uart_unlock_and_check_sysrq() helper can be used to defer processing
of sysrq until the interrupt handler has released the port lock and is
about to return.
Since commit 81e2073c17 ("genirq: Disable interrupts for force
threaded handlers") interrupt handlers that are not explicitly requested
as threaded are always called with interrupts disabled and there is no
need to save the interrupt state when taking the port lock.
Instead of adding another sysrq helper for when the interrupt state has
not needlessly been saved, drop the state parameter from
uart_unlock_and_check_sysrq() and update its callers to no longer
explicitly disable interrupts in their interrupt handlers.
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210416140557.25177-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull OPP (Operating Performance Points) framework updates for v5.13
from Viresh Kumar:
"This adds devm variants for OPP APIs and updates few of the users
as well (Yangtao Li and Dmitry Osipenko)."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
memory: samsung: exynos5422-dmc: Convert to use resource-managed OPP API
drm/panfrost: Convert to use resource-managed OPP API
drm/lima: Convert to use resource-managed OPP API
mmc: sdhci-msm: Convert to use resource-managed OPP API
spi: spi-qcom-qspi: Convert to use resource-managed OPP API
spi: spi-geni-qcom: Convert to use resource-managed OPP API
serial: qcom_geni_serial: Convert to use resource-managed OPP API
opp: Change return type of devm_pm_opp_attach_genpd()
opp: Change return type of devm_pm_opp_register_set_opp_helper()
opp: Add devres wrapper for dev_pm_opp_of_add_table
opp: Add devres wrapper for dev_pm_opp_set_supported_hw
opp: Add devres wrapper for dev_pm_opp_set_regulators
opp: Add devres wrapper for dev_pm_opp_set_clkname
Drivers can return -ENOIOCTLCMD when an ioctl is not recognised to tell
the upper layers to continue looking for a handler.
This is not the case for the RS485 and ISO7816 ioctls whose handlers
should return -ENOTTY directly in case a serial driver does not
implement the corresponding methods.
Fixes: a5f276f10f ("serial_core: Handle TIOC[GS]RS485 ioctls.")
Fixes: ad8c0eaa0a ("tty/serial_core: add ISO7816 infrastructure")
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210407095208.31838-9-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers should return -ENOTTY ("Inappropriate I/O control operation")
when an ioctl isn't supported, while -EINVAL is used for invalid
arguments.
Support for termiox was added by commit 1d65b4a088 ("tty: Add
termiox") in 2008 but no driver support ever followed and it was
recently ripped out by commit e0efb3168d ("tty: Remove dead termiox
code").
Fix the return value for the unsupported termiox ioctls, which have
always returned -EINVAL, by explicitly returning -ENOTTY rather than
removing them completely and falling back to the default unrecognised-
ioctl handling.
Fixes: 1d65b4a088 ("tty: Add termiox")
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210407095208.31838-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers should return -ENOTTY ("Inappropriate I/O control operation")
when an ioctl isn't supported, while -EINVAL is used for invalid
arguments.
Fix up the TIOCMGET, TIOCMSET and TIOCGICOUNT helpers which returned
-EINVAL when a tty driver did not implement the corresponding
operations.
Note that the TIOCMGET and TIOCMSET helpers predate git and do not get a
corresponding Fixes tag below.
Fixes: d281da7ff6 ("tty: Make tiocgicount a handler")
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210407095208.31838-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
A non-privileged user has only ever been able to set the since long
deprecated ASYNC_SPD flags and trying to change any other *supported*
feature should result in -EPERM being returned. Setting the current
values for any supported features should return success.
Fix the moxa implementation which was returning -EPERM also for a
privileged user when trying to change certain unsupported parameters and
instead return success consistently.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210407102334.32361-13-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty-port close_delay and closing_wait parameters set by TIOCSSERIAL
are specified in jiffies, while the values returned by TIOCGSERIAL are
specified in centiseconds.
Add the missing conversions so that TIOCSSERIAL works as expected also
if this code is ever reused on a system where HZ is not 100.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210407102334.32361-10-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6ac9b61786 ("soc: fsl: qe: introduce qe_io{read,write}*
wrappers") added specific I/O accessors for qe because at that
time ioread/iowrite functions were sub-optimal on powerpc/32
compared to the architecture specific in_/out_ IO accessors.
But as ioread/iowrite accessors are now equivalent since
commit 894fa235eb ("powerpc: inline iomap accessors"),
use them in order to allow removal of the qe specific ones.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
A test was added to the probe function to ensure the device was
actually connected and working before successfully completing a
probe. If the device was actually there, but the I2C bus was not
ready yet for whatever reason, the probe fails permanently.
Change the probe so that we defer the probe on a regmap read
failure so that we try the probe again when the dependent drivers
are potentially loaded. This should not affect the case where the
device truly isn't present because the probe will never successfully
complete.
Fixes: 2aa916e67d ("sc16is7xx: Read the LSR register for basic device presence check")
Cc: stable@vger.kernel.org
Signed-off-by: Annaliese McDermond <nh6z@nh6z.net>
Link: https://lore.kernel.org/r/010101787f9c3fd8-c1815c00-2d6b-4c85-a96a-a13e68597fda-000000@us-west-2.amazonses.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
