The knowledge about the HDMI/DVI DDI translation table was scattered
around.
- info->hdmi_level_shift was initialized with 6, the index of the 800
mV, 0dB translation
- A check on the VBT value was done to ensure it wasn't overflowing
the translation table (< 0xC)
- The actual programming was done in intel_ddi.c
As we need to change that knowledge for Broadwell, let's gather
everything into one place.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With this bit enabled, HW changes the color when compressing frames for
debug purposes.
ALthough the simple way to enable a single bit is over intel_reg_write,
this value is overwriten on next update_fbc so depending on the workload
it is not possible to set this bit with intel-gpu-tools. So this patch
introduces a persistent way to enable false color over debugfs.
v2: Use DEFINE_SIMPLE_ATTRIBUTE as Daniel suggested
v3: (Ville) only do false color for IVB+ since according to spec bit is
MBZ before IVB.
v4: We don't have FBC on valleyview nor on cherryview (Ben)
v5: s/!HAS_PCH_SPLIT/!HAS_FBC (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I'm not really that insisting on checkpath compliance, but ragged
function paramter alignment does get me. Please adjust your editor to
just do this for you.
Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Updated the error log as suggested by Imre
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV display PHY registes have two swing margin/deemph settings. Make it
clear which ones we're using.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV was forgotten the intel_{dp,hdmi}_prepare() were introduced (or the
chv patches were still in flight?). Call these when enabling the ports.
Things tend to work much better when we actually write something
to the port registers :)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We enable the DPLL refclock already when bringing up the cmnlane power
well, so also leave it on when otherwise disabling the DPLL.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Punit seems a bit WIP still. Disable cdclk changes until we have
hardware where it works.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Looks like the Punit is supposed to support the 400MHz cdclk directly on
chv, so we don't need the vlv tricks.
FIXME: Punit doesn't seem ready for this yet on current hw
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we started using intel_runtime_pm_disable_interrupts() at normal
(non-runtime) suspend/resume, we had to remove a WARN from
ironlake_disable_display_irq to avoid a case where we were doing the
correct thing and the WARN was not really needed. The problem is that
the WARN was useful in other cases, and its removal can hide some bugs
that we would catch automatically.
To be able to add back the WARN, we have to call intel_crtc_control()
before interrupts are disabled, which is what this patch currently
does.
Also notice that Ville's patch from the Watermarks series "drm/i915:
Leave interrupts enabled while disabling crtcs during suspend" also
did a change that's equivalent to the one we're doing on this patch,
with the exception that its original patch, when applied to the
current tree, procduces a WARN.
Related commits:
commit daa390e5ee45cc051d6bf37b296901f2f92b002d
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
drm/i915: don't warn if IRQs are disabled when shutting down display IRQs
commit e11aa36230
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
drm/i915: use runtime irq suspend/resume in freeze/thaw
Note that the function part of this patch has already been done in
commit 0e32b39cee
Author: Dave Airlie <airlied@redhat.com>
Date: Fri May 2 14:02:48 2014 +1000
drm/i915: add DP 1.2 MST support (v0.7)
with the fixup
commit 09b64267c1
Author: Dave Airlie <airlied@redhat.com>
Date: Wed Jul 23 14:25:24 2014 +1000
drm/i915: don't suspend gt until after we disable irqs and display (v2)
so all that's left from Paulo's patch is reinstating the WARNING.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Explain conflict resolution with Dave's DP MST patches with a
note in the commit message.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Turns out we were again way too naive and optimistic, of course things
will change.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is only going to get worse, so split it now to avoid adding more
cases to the if/else ladder.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We'll need a different algorithm to select the shared DPLL.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since the run-time PM on DPMS series, this function has an outdated
comment. Refresh it a bit.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Future platform will use config->ddi_pll_sel in a different way.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So we can easily provide an alternate implementation in the future.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Not all those fields are valid on a given platform. Make it explicit.
Unions could also be used, but were cluttering some code paths with
if/else ladders.
v2: Don't use anonymous unions (Daniel)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Split some WM debug prints to multiple lines. This shouldn't hurt
grappability since the important part is at the start and the rest
is just repeated stuff for each pipe.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to the specifications bit 6 is actually valid in the stride register.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add the TX wells for port D. The Punit subsystem numbers are a total
guess at this time. Also I'm not sure these even exist. Certainly the
Punit in current hardware doesn't deal with these.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add the TX wells for ports B and C just like on VLV.
Again Punit doesn't seem ready (or the wells don't even exist anymore)
so leave it iffed out.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has a power well for each pipe. Add the code to deal with them.
The Punit in current hardware doesn't seem ready for this yet, so
leave it iffed out.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Not sure if it's still there since chv has per-pipe power wells.
At least with current Punit this doesn't work. Also the display
irq handling would need to be adjusted for pipe C. So leave the
code iffed out for now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Both VLV and CHV handle the cmnreset stuff in the power well code now,
so intel_reset_dpio() is no longer needed.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has two display PHYs so there are also two cmnlane power wells. Add
the approriate code to power the wells up/down.
Like on VLV we do the cmnreset assert/deassert and the DPLL refclock
enabling at approriate times.
This code actually works on my bsw.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add chv_power_wells[] so we can start to build up the power well support
for chv. Just the "always on" well there initialy.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Share the waitqueue that drm_irq uses when performing the vblank evade
trick for atomic pipe updates.
v2: Keep intel_pipe_handle_vblank() (Chris)
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a small static inline helper to grab the vblank wait queue based on
the drm_crtc.
This is useful for drivers to do internal vblank waits using
wait_event() & co.
v2: Pimp commit message (Daniel)
Add kernel doc (Daniel)
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding relevant read out comparison code, in check_crtc_state, for the new
member of crtc_config, dp_m2_n2, which was introduced to store link_m_n
values for a DP downclock mode (if available). Suggested by Daniel.
v2: Changed patch title.
Daniel's review comments incorporated.
Added relevant state readout code for M2_N2. dp_m2_n2 comparison to be done
only when high RR is not in use (This is because alternate m_n register
programming will be done only when low RR is being used).
v3: Modified call to get_m2_n2 which had dp_m_n as param by mistake.
Compare dp_m_n and dp_m2_n2 for gen 7 and below. compare the structures
based on DRRS state for gen 8 and above.
Save and restore M2 N2 registers for gen 7 and below
v4: For Gen>=8, check M_N registers against dp_m_n and dp_m2_n2 as there is
only one set of M_N registers
v5: Removed the chunk which saves and restores M2_N2 registers. Modified
get_m_n() to get M2_N2 registers as well. Modified the macro which compares
hw.dp_m_n against sw.dp_m2_n2/sw.dp_m_n for gen > 8.
v6: Added check to compare dp_m2_n2 only when DRRS is enabled
v7: Modified drrs check to use has_drrs
v8: Add has_drrs check before reading M2_N2 registers
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For Gen < 8, set M2_N2 registers on every mode set. This is required to make
sure M2_N2 registers are set during boot, resume from sleep for cross-
checking the state. The register is set only if DRRS is supported.
v2: Patch rebased
v3: Daniel's review comments
- Removed HAS_DRRS(dev) and added bool has_drrs to pipe_config to
track drrs support
v4: Jesse's review comments
- Made changes to set m2_n2 in intel_dp_set_m_n()
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 521e62e49a.
Although POST_SYNC brought a bit of stability to Semaphores on BDW
it didn't solved all issues and some hungs can still occour when
semaphores are enabled on BDW. Also some sloweness can be found on some
igt tests, althoguth it apparently doesn't affect real workloads.
Besides that, no real performance gain was found on our tests with different
and even multiple workloads.
Let's disable it again for now. At least until we are sure it is safe
to re-enable it.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Withtout this, ring initialization fails reliabily during resume with
[drm:init_ring_common] *ERROR* render ring initialization failed ctl 0001f001 head ffffff8804 tail 00000000 start 000e4000
This is not a complete fix, but it is verified to make the ring
initialization failures during resume much less likely.
We were not able to root-cause this bug (likely HW-specific to Gen4 chips)
yet. This is therefore used as a ducttape before problem is fully
understood and proper fix created, so that people don't suffer from
completely unusable systems in the meantime.
The discussion and debugging is happening at
https://bugs.freedesktop.org/show_bug.cgi?id=76554
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This particular nasty presented itself while trying to register the
intelfb device (intel_fbdev.c). During the process of registering the device
the driver will disable the crtc via i9xx_crtc_disable. These will
also disable the panel using the generic mipi panel functions in
dsi_mod_vbt_generic.c. The stale MIPI generic data sequence pointers would
cause a crash within those functions. However, all of this is happening
while console_lock is held from do_register_framebuffer inside fbcon.c. Which
means that you got kernel log and just the device appearing to reboot/hang for
no apparent reason.
The fault started from the FB_EVENT_FB_REGISTERED event using the
fb_notifier_call_chain call in fbcon.c.
This regression has been introduced in
commit d3b542fcfc
Author: Shobhit Kumar <shobhit.kumar@intel.com>
Date: Mon Apr 14 11:00:34 2014 +0530
drm/i915: Add parsing support for new MIPI blocks in VBT
Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
[danvet: Add regression citation.]
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We might be leaving the PGU Frequency (and thus vnn) high during the suspend.
Flusing the delayed work queue should take care of this.
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BDW has many other Display Engine interrupts and GT interrupts registers.
Collecting it properly on gpu_error_state.
On debugfs all was properly listed already but besides we were also listing old
DEIER and GTIER that doesn't exist on BDW anymore. This was causing
unclaimed register messages
v2: Fix small issues of first version and don't read DEIER regs when pipe's
power well is disabled
v3: bikeshed accepted: use enum pipe pipe instead of int i for pipe interection
v4: Ben notice previous version was checking for display_power_enabled without
using propper locks. Using _unlocked version isn't reliable and we cannot
get this registers when power well is off. So let's avoid getting all DE_IER
per pipe for now. If someone think this is an useful information it can be
added later.
v5: Ben: put back debugfs stuff that might be coverred by pm_get and use
gen >= 8 trying to predict future.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=81701
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: (v3) Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the actual head has progressed forward inside a batch (request),
don't accumulate hangcheck score.
As the hangcheck score in increased only by acthd jumping backwards,
the result is that we only declare an active batch as stuck if it is
trapped inside a loop. Or that the looping will dominate the batch
progression so that it overcomes the bonus that forward progress gives.
v2: Improved commit message (Chris Wilson)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: s/active_loop/active (loop)/ as requested by Chris.]
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Broadwell, any PIPE_CONTROL with the "State Cache Invalidate" bit set
must be preceded by a PIPE_CONTROL with the "CS Stall" bit set.
Documented on the BSpec 3D workarounds page.
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
[vsyrjala: add chv w/a note too]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We'll want to reuse this for a workaround.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Rmove now unused int.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DDL registers can hold 7bit numbers. Make the most of those seven
bits by adjusting the threshold where we switch between the 64 vs. 32
precision multipliers.
Also we compute 'entries' to make the decision about precision, and then
we recompute the same value to calculate the actual drain latency. Just
use the already calculate 'entries' there.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GTIER and DEIER doesn't have same interface on HSW so this "or" operation
makes the information provided useless.
v2: since we have gtier variable already let's split for everybody
and avoid the strange | op.
Also avoid overriding the value that was set for vlv. In this case I
believe that we should reorganize the whole function, but I'll respect
the comment that ask to not touch the order and let this organization
work to be done later.
v3: moving VLV check to the right place.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Users often can't do anything about this since their vendors stopped
providing BIOS updates. Also we seem to be able to hack around it
with increased latency values, and thus far the only reports have
been for screens with really high resolutions. So tune it down to a
level where only developers can see it.
Also drop some of the end-user fluff.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Power users spot this and then get adventurous and try to adjust
module driver options. Nothing good ever came out of that, so
hide it better.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since I've reworked psr support to no longer require x-tiling we don't
check any state protected by the Giant GEM Lock. So drop that check.
Also boo for lockdep_assert_held for not yelling when lockdep is
disabled.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reported-by: Paulo Zanoni <przanoni@gmail.com>
Acked-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix signal_offset when recording semaphore state on BDW.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
