After secondary CPU boot or hotplug, the active_mm of the idle thread is
&init_mm. The init_mm.pgd (swapper_pg_dir) is only meant for TTBR1_EL1
and must not be set in TTBR0_EL1. Since when active_mm == &init_mm the
TTBR0_EL1 is already set to the reserved value, there is no need to
perform any context reset.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org>
Use a sized unsigned 32-bit data type (u32) to store register contents.
The DPAUX registers are 32 bits wide irrespective of the architecture's
data width.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Pages allocated from shmemfs don't end up being cleared and flushed on
ARMv7, so they must be flushed explicitly. Use the DMA mapping API for
that purpose, even though it's not used for anything else.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The IOMMU may not always be able to address 2 GiB of memory. On Tegra20,
the GART supports 32 MiB starting at 0x58000000. Also the aperture on
Tegra30 and later is in fact the full 4 GiB, rather than just 2 GiB as
currently assumed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DPAUX read/write FIFO registers aren't sequential in the register
space, causing transfers larger than 4 bytes to cause accesses to non-
existing FIFO registers.
Fixes: 6b6b604215 ("drm/tegra: Add eDP support")
Signed-off-by: Thierry Reding <treding@nvidia.com>
So far, we configured the world-switch by having a small array
of pointers to the save and restore functions, depending on the
GIC used on the platform.
Loading these values each time is a bit silly (they never change),
and it makes sense to rely on the instruction patching instead.
This leads to a nice cleanup of the code.
Acked-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add a new item to the feature set (ARM64_HAS_SYSREG_GIC_CPUIF)
to indicate that we have a system register GIC CPU interface
This will help KVM switching to alternative instruction patching.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Update Kconfig with enhanced help text for hid-plantronics driver.
Update hid-plantronics.c to identify device type and correctly map
either the vendor unique or consumer control volume up/down usages
to KEY_VOLUMEUP and KEY_VOLUMEDOWN events. Unmapped usages are ignored
to prevent core mapping of unknown usages to random mouse events.
Tested on ChromeBox/ChromeBook with various Plantronics devices.
Signed-off-by: Terry Junge <terry.junge@plantronics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
the enum of "DAC Polarity" should be wm8960_enum[1].
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This reverts commit 48a9db462d.
Some platforms actually need support for the memset operations. Bring it back.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The AT91 HDMAC controller supports interleaved transfers through what's
called the Picture-in-Picture mode, which allows to transfer a squared
portion of a framebuffer.
This means that this interleaved transfer only supports interleaved
transfers which have a transfer size and ICGs that are fixed across all the
chunks.
While this is a quite drastic restriction of the interleaved transfers
compared to what the dmaengine API allows, this is still useful, and our
driver will only reject transfers that do not conform to this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that we can have ICGs set for both the source and destination (using
the icg field of struct data_chunk) or for only the source or the
destination (using the dst_icg or src_icg respectively), and that these
fields can be ignored depending on other parameters (src_inc, src_sgl,
etc.), the logic to get the actual ICG value can be quite tricky.
The XDMAC driver was already implementing it, but since we will need it in
other drivers, we can move it to the main header file.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We store the rule blob per (possible) cpu. Unfortunately this means we can
waste lot of memory on big smp machines. ipt_entry structure ('rule head')
is 112 byte, so e.g. with maxcpu=64 one single rule eats
close to 8k RAM.
Since previous patch made counters percpu it appears there is nothing
left in the rule blob that needs to be percpu.
On my test system (144 possible cpus, 400k dummy rules) this
change saves close to 9 Gigabyte of RAM.
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The binary arp/ip/ip6tables ruleset is stored per cpu.
The only reason left as to why we need percpu duplication are the rule
counters embedded into ipt_entry et al -- since each cpu has its own copy
of the rules, all counters can be lockless.
The downside is that the more cpus are supported, the more memory is
required. Rules are not just duplicated per online cpu but for each
possible cpu, i.e. if maxcpu is 144, then rule is duplicated 144 times,
not for the e.g. 64 cores present.
To save some memory and also improve utilization of shared caches it
would be preferable to only store the rule blob once.
So we first need to separate counters and the rule blob.
Instead of using entry->counters, allocate this percpu and store the
percpu address in entry->counters.pcnt on CONFIG_SMP.
This change makes no sense as-is; it is merely an intermediate step to
remove the percpu duplication of the rule set in a followup patch.
Suggested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Some regulators can limit their input current (typically annotated
as ilim). Add an op (set_input_current_limit) and a DT property +
constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators support a "soft start" feature where the voltage
ramps up slowly when the regulator is enabled. Add an op
(set_soft_start) and a DT property + constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If bridge netfilter is used with both
bridge-nf-call-iptables and bridge-nf-filter-vlan-tagged enabled
then ip fragments in VLAN frames are sent without the vlan header.
This has never worked reliably. Turns out this relied on pre-3.5
behaviour where skb frag_list was used to store ip fragments;
ip_fragment() then re-used these skbs.
But since commit 3cc4949269
("ipv4: use skb coalescing in defragmentation") this is no longer
the case. ip_do_fragment now needs to allocate new skbs, but these
don't contain the vlan tag information anymore.
Fix it by storing vlan information of the ressembled skb in the
br netfilter percpu frag area, and restore them for each of the
fragments.
Fixes: 3cc4949269 ("ipv4: use skb coalescing in defragmentation")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
since commit d6b915e29f
("ip_fragment: don't forward defragmented DF packet") the largest
fragment size is available in the IPCB.
Therefore we no longer need to care about 'encapsulation'
overhead of stripped PPPOE/VLAN headers since ip_do_fragment
doesn't use device mtu in such cases.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
IPv6 fragmented packets are not forwarded on an ethernet bridge
with netfilter ip6_tables loaded. e.g. steps to reproduce
1) create a simple bridge like this
modprobe br_netfilter
brctl addbr br0
brctl addif br0 eth0
brctl addif br0 eth2
ifconfig eth0 up
ifconfig eth2 up
ifconfig br0 up
2) place a host with an IPv6 address on each side of the bridge
set IPv6 address on host A:
ip -6 addr add fd01:2345:6789:1::1/64 dev eth0
set IPv6 address on host B:
ip -6 addr add fd01:2345:6789:1::2/64 dev eth0
3) run a simple ping command on host A with packets > MTU
ping6 -s 4000 fd01:2345:6789:1::2
4) wait some time and run e.g. "ip6tables -t nat -nvL" on the bridge
IPv6 fragmented packets traverse the bridge cleanly until somebody runs.
"ip6tables -t nat -nvL". As soon as it is run (and netfilter modules are
loaded) IPv6 fragmented packets do not traverse the bridge any more (you
see no more responses in ping's output).
After applying this patch IPv6 fragmented packets traverse the bridge
cleanly in above scenario.
Signed-off-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
[pablo@netfilter.org: small changes to br_nf_dev_queue_xmit]
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Prepare check_hbh_len() to be called from newly introduced
br_validate_ipv6() in next commit.
Signed-off-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Some regulators need to be configured to pull down a resistor
when the regulator is disabled. Add an op (set_pull_down) and a
DT property + constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
br_parse_ip_options() does not parse any IP options, it validates IP
packets as a whole and the function name is misleading.
Rename br_parse_ip_options() to br_validate_ipv4() and remove unneeded
commments.
Signed-off-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently frag_max_size is member of br_input_skb_cb and copied back and
forth using IPCB(skb) and BR_INPUT_SKB_CB(skb) each time it is changed or
used.
Attach frag_max_size to nf_bridge_info and set value in pre_routing and
forward functions. Use its value in forward and xmit functions.
Signed-off-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
IPv4 iptables allows to REDIRECT/DNAT/SNAT any traffic over a bridge.
e.g. REDIRECT
$ sysctl -w net.bridge.bridge-nf-call-iptables=1
$ iptables -t nat -A PREROUTING -p tcp -m tcp --dport 8080 \
-j REDIRECT --to-ports 81
This does not work with ip6tables on a bridge in NAT66 scenario
because the REDIRECT/DNAT/SNAT is not correctly detected.
The bridge pre-routing (finish) netfilter hook has to check for a possible
redirect and then fix the destination mac address. This allows to use the
ip6tables rules for local REDIRECT/DNAT/SNAT REDIRECT similar to the IPv4
iptables version.
e.g. REDIRECT
$ sysctl -w net.bridge.bridge-nf-call-ip6tables=1
$ ip6tables -t nat -A PREROUTING -p tcp -m tcp --dport 8080 \
-j REDIRECT --to-ports 81
This patch makes it possible to use IPv6 NAT66 on a bridge. It was tested
on a bridge with two interfaces using SNAT/DNAT NAT66 rules.
Reported-by: Artie Hamilton <artiemhamilton@yahoo.com>
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
[bernhard.thaler@wvnet.at: rebased, add indirect call to ip6_route_input()]
[bernhard.thaler@wvnet.at: rebased, split into separate patches]
Signed-off-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Put br_nf_pre_routing_finish_ipv6() after daddr_was_changed() and
br_nf_pre_routing_finish_bridge() to prepare calling these functions
from there.
Signed-off-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
use binary AND on complement of BRNF_NF_BRIDGE_PREROUTING to unset
bit in nf_bridge->mask.
Signed-off-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
After db29a9508a ("netfilter: conntrack: disable generic tracking for
known protocols"), if the specific helper is built but not loaded
(a standard for most distributions) systems with a restrictive firewall
but weak configuration regarding netfilter modules to load, will
silently stop working.
This patch then puts a warning message so the sysadmin knows where to
start looking into. It's a pr_warn_once regardless of protocol itself
but it should be enough to give a hint on where to look.
Cc: Florian Westphal <fw@strlen.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Some regulators have a fixed load that isn't captured by
consumers that the kernel knows about. Add a constraint to
support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add mclk-fs ratio property per dai-link sub node. This will
allow to manage several codecs with different ratio.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixed below error/warnings
sound/built-in.o: In function `rt5645_i2c_probe':
>> rt5645.c:(.text+0xe38f5): undefined reference to
>> `devm_regmap_init_i2c'
sound/built-in.o: In function `rt5645_i2c_driver_exit':
>> rt5645.c:(.exit.text+0x60e): undefined reference to `i2c_del_driver'
sound/built-in.o: In function `rt5645_i2c_driver_init':
>> rt5645.c:(.init.text+0x1a90): undefined reference to
>> `i2c_register_driver'
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since hp-detect is optional, use devm_gpiod_get_optional instead.
In additional, it should return error if devm_gpiod_get_optional fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This was spotted by Fernando Lopez-Lezcano <nando@ccrma.Stanford.EDU>
while he tried to compile a -RT kernel with this driver enabled.
"make C=2" would also warn about this. This is is based on his patch.
Reported-by: Fernando Lopez-Lezcano <nando@ccrma.Stanford.EDU>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is currently possible to have CONFIG_SND_ATMEL_SOC_SSC=y with either
CONFIG_SND_ATMEL_SOC_PDC=m or CONFIG_SND_ATMEL_SOC_DMA=m. This results in a
driver that compiles but does not link with this kind of error:
sound/built-in.o: In function `atmel_ssc_set_audio':
(.text+0x87d90): undefined reference to `atmel_pcm_pdc_platform_register'
sound/built-in.o: In function `atmel_ssc_put_audio':
(.text+0x8879a): undefined reference to `atmel_pcm_pdc_platform_unregister'
Introduce new config options SND_ATMEL_SOC_SSC_PDC and
SND_ATMEL_SOC_SSC_DMA which should be used by the board drivers and the
correct logic to properly select the SND_ATMEL_SOC_PDC and
SND_ATMEL_SOC_DMA states.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After discussing with the Kconfig maintainer, we found a better fiw
allowing to keep each driver as modules.
This reverts commit 0ef9dc139d.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Although the extended tables are theoretically a completely orthogonal
feature to PASID and anything else that *uses* the newly-available bits,
some of the early hardware has problems even when all we do is enable
them and use only the same bits that were in the old context tables.
For now, there's no motivation to support extended tables unless we're
going to use PASID support to do SVM. So just don't use them unless
PASID support is advertised too. Also add a command-line bailout just in
case later chips also have issues.
The equivalent problem for PASID support has already been fixed with the
upcoming VT-d spec update and commit bd00c606a ("iommu/vt-d: Change
PASID support to bit 40 of Extended Capability Register"), because the
problematic platforms use the old definition of the PASID-capable bit,
which is now marked as reserved and meaningless.
So with this change, we'll magically start using ECS again only when we
see the new hardware advertising "hey, we have PASID support and we
actually tested it this time" on bit 40.
The VT-d hardware architect has promised that we are not going to have
any reason to support ECS *without* PASID any time soon, and he'll make
sure he checks with us before changing that.
In the future, if hypothetical new features also use new bits in the
context tables and can be seen on implementations *without* PASID support,
we might need to add their feature bits to the ecs_enabled() macro.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Modify the RT5645 driver to parse platform data from device tree. This is
missing from previous patch in sound/soc/codecs/rt5645.c, that was present
in v3.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch corrected pcm_delay calculation in BSW sst driver
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch separates the IO function from the rt286. It is prepared to share
for new chips that support the same IO function.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MD_RECOVERY_DONE is normally cleared by md_check_recovery after a
resync etc finished. However it is possible for raid5_start_reshape
to race and start a reshape before MD_RECOVERY_DONE is cleared. This
can lean to multiple reshapes running at the same time, which isn't
good.
To make sure it is cleared before starting a reshape, and also clear
it when reaping a thread, just to be safe.
Signed-off-by: NeilBrown <neilb@suse.de>
Checking ->sync_thread without holding the mddev_lock()
isn't really safe, even after flushing the workqueue which
ensures md_start_sync() has been run.
While this code is waiting for the lock, md_check_recovery could reap
the thread itself, and then start another thread (e.g. recovery might
finish, then reshape starts). When this thread gets the lock
md_start_sync() hasn't run so it doesn't get reaped, but
MD_RECOVERY_RUNNING gets cleared. This allows two threads to start
which leads to confusion.
So don't both if MD_RECOVERY_RUNNING isn't set, but if it is do
the flush and the test and the reap all under the mddev_lock to
avoid any race with md_check_recovery.
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: 6791875e2e ("md: make reconfig_mutex optional for writes to md sysfs files.")
Cc: stable@vger.kernel.org (v4.0+)
Returning zero from a 'store' function is bad.
The return value should be either len length of the string
or an error.
So use 'len' if 'err' is zero.
Fixes: 6791875e2e ("md: make reconfig_mutex optional for writes to md sysfs files.")
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@vger.kernel (v4.0+)
The encryption key size is read only for BR/EDR (ACL_LINK) connections
so there's no need to check for it in the read_enc_key_size_complete()
callback.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some drivers implement only pause operation (no resuming). Example is
pl330 where pause is needed for getting residuum. pl330 does not support
resume operation, transfer must be stopped after pause.
However for slaves this is exposed always as "pause and resume" which
introduces subtle errors on Odroid U3 board (Exynos4412 with pl330).
After adding pause function to pl330 driver the audio playback
(utilizing DMA) gets choppy after some time (approximately 24 hours).
Fix this by exposing "cmd_pause" if and only if pause and resume are
implemented.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: gabriel@unseen.is
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: <stable@vger.kernel.org>
Fixes: 88987d2c75 ("dmaengine: pl330: add DMA_PAUSE feature")
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes commits ("mac802154: cleanup ieee802154 hardware flags")
bcbfd2078d and ("mac802154: cleanup address
filtering flags") 6b70a43c7e by starting
the flags definitions at BIT(0) which is same like the previous behaviour.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Omit setting the polarity to normal during probe and instead use the new
pwmchip_add_with_polarity() function to register a PWM chip with inverse
polarity by default for all channels to reflect the hardware default.
Signed-off-by: Arun Ramamurthy <arunrama@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Tim Kryger <tim.kryger@gmail.com>
Signed-off-by: Jonathan Richardson <jonathar@broadcom.com>
[thierry.reding@gmail.com: use pwmchip_add_with_polarity()]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This patch changes the setting of llsec param flag with the BIT macro.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When pairing over SMP over BR/EDR the generated LTK has by default the
same key size as the BR/EDR Link Key. Make sure we don't set our
Pairing Request/Response max value to anything higher than that.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
