Pin sense will active when power pin is wake up.
Power pin will not wake up immediately during resume state.
Add some delay to wait for power pin activated.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dirty logging tracks sptes in 4k granularity, meaning that large sptes
have to be split. If live migration is successful, the guest in the
source machine will be destroyed and large sptes will be created in the
destination. However, the guest continues to run in the source machine
(for example if live migration fails), small sptes will remain around
and cause bad performance.
This patch introduce lazy collapsing of small sptes into large sptes.
The rmap will be scanned in ioctl context when dirty logging is stopped,
dropping those sptes which can be collapsed into a single large-page spte.
Later page faults will create the large-page sptes.
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Message-Id: <1428046825-6905-1-git-send-email-wanpeng.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
CR2 is not cleared as it should after reset. See Intel SDM table named "IA-32
Processor States Following Power-up, Reset, or INIT".
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1427933438-12782-5-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
DR0-DR3 are not cleared as they should during reset and when they are set from
userspace. It appears to be caused by c77fb5fe6f ("KVM: x86: Allow the guest
to run with dirty debug registers").
Force their reload on these situations.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1427933438-12782-4-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After reset, the CPU can change the BSP, which will be used upon INIT. Reset
should return the BSP which QEMU asked for, and therefore handled accordingly.
To quote: "If the MP protocol has completed and a BSP is chosen, subsequent
INITs (either to a specific processor or system wide) do not cause the MP
protocol to be repeated."
[Intel SDM 8.4.2: MP Initialization Protocol Requirements and Restrictions]
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1427933438-12782-3-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
recalculate_apic_map() uses two passes over all VCPUs. This is a relic
from time when we selected a global mode in the first pass and set up
the optimized table in the second pass (to have a consistent mode).
Recent changes made mixed mode unoptimized and we can do it in one pass.
Format of logical MDA is a function of the mode, so we encode it in
apic_logical_id() and drop obsoleted variables from the struct.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Message-Id: <1423766494-26150-5-git-send-email-rkrcmar@redhat.com>
[Add lid_bits temporary in apic_logical_id. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We want to support mixed modes and the easiest solution is to avoid
optimizing those weird and unlikely scenarios.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Message-Id: <1423766494-26150-4-git-send-email-rkrcmar@redhat.com>
[Add comment above KVM_APIC_MODE_* defines. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Broadcast allowed only one global APIC mode, but mixed modes are
theoretically possible. x2APIC IPI doesn't mean 0xff as broadcast,
the rest does.
x2APIC broadcasts are accepted by xAPIC. If we take SDM to be logical,
even addreses beginning with 0xff should be accepted, but real hardware
disagrees. This patch aims for simple code by considering most of real
behavior as undefined.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Message-Id: <1423766494-26150-3-git-send-email-rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In mixed modes, we musn't deliver xAPIC IPIs like x2APIC and vice versa.
Instead of preserving the information in apic_send_ipi(), we regain it
by converting all destinations into correct MDA in the slow path.
This allows easier reasoning about subsequent matching.
Our kvm_apic_broadcast() had an interesting design decision: it didn't
consider IOxAPIC 0xff as broadcast in x2APIC mode ...
everything worked because IOxAPIC can't set that in physical mode and
logical mode considered it as a message for first 8 VCPUs.
This patch interprets IOxAPIC 0xff as x2APIC broadcast.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Message-Id: <1423766494-26150-2-git-send-email-rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Drop unused static procedure which doesn't have callers within its
translation unit. It had been already removed independently in QEMU[1]
from the OpenPIC implementation borrowed from the kernel.
[1] https://lists.gnu.org/archive/html/qemu-devel/2014-06/msg01812.html
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Cc: Alexander Graf <agraf@suse.de>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1424768706-23150-3-git-send-email-asolokha@kb.kras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After speed-up of cpuid_maxphyaddr() it can be called frequently:
instead of heavyweight enumeration of CPUID entries it returns a cached
pre-computed value. It is also inlined now. So caching its result became
unnecessary and can be removed.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Message-Id: <20150329205644.GA1258@gnote>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On each VM-entry CPU should check the following VMCS fields for zero bits
beyond physical address width:
- APIC-access address
- virtual-APIC address
- posted-interrupt descriptor address
This patch adds these checks required by Intel SDM.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Message-Id: <20150329205627.GA1244@gnote>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
cpuid_maxphyaddr(), which performs lot of memory accesses is called
extensively across KVM, especially in nVMX code.
This patch adds a cached value of maxphyaddr to vcpu.arch to reduce the
pressure onto CPU cache and simplify the code of cpuid_maxphyaddr()
callers. The cached value is initialized in kvm_arch_vcpu_init() and
reloaded every time CPUID is updated by usermode. It is obvious that
these reloads occur infrequently.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Message-Id: <20150329205612.GA1223@gnote>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Exposing the on-stack error code with internal error is cheap and
potentially useful.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Message-Id: <1428001865-32280-1-git-send-email-rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If we were migrated right after __getcpu, but before reading the
migration_count, we wouldn't notice that we read TSC of a different
VCPU, nor that KVM's bug made pvti invalid, as only migration_count
on source VCPU is increased.
Change vdso instead of updating migration_count on destination.
Cc: stable@vger.kernel.org
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Fixes: 0a4e6be9ca ("x86: kvm: Revert "remove sched notifier for cross-cpu migrations"")
Message-Id: <1428000263-11892-1-git-send-email-rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The corresponding write functions just use __copy_to_user. Do the
same on the read side.
This reverts what's left of commit 86ab8cffb4 (KVM: introduce
gfn_to_hva_read/kvm_read_hva/kvm_read_hva_atomic, 2012-08-21)
Cc: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1427976500-28533-1-git-send-email-pbonzini@redhat.com>
The newly-added tracepoint shows the following results on
the tscdeadline_latency test:
qemu-kvm-8387 [002] 6425.558974: kvm_vcpu_wakeup: poll time 10407 ns
qemu-kvm-8387 [002] 6425.558984: kvm_vcpu_wakeup: poll time 0 ns
qemu-kvm-8387 [002] 6425.561242: kvm_vcpu_wakeup: poll time 10477 ns
qemu-kvm-8387 [002] 6425.561251: kvm_vcpu_wakeup: poll time 0 ns
and so on. This is because we need to go through kvm_vcpu_block again
after the timer IRQ is injected. Avoid it by polling once before
entering kvm_vcpu_block.
On my machine (Xeon E5 Sandy Bridge) this removes about 500 cycles (7%)
from the latency of the TSC deadline timer.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename the old __vcpu_run to vcpu_run, and extract part of it to a new
function vcpu_block.
The next patch will add a new condition in vcpu_block, avoid extra
indentation.
Reviewed-by: David Matlack <dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Guest can't be booted w/ ept=0, there is a message dumped as below:
If you're running a guest on an Intel machine without unrestricted mode
support, the failure can be most likely due to the guest entering an invalid
state for Intel VT. For example, the guest maybe running in big real mode
which is not supported on less recent Intel processors.
EAX=00000011 EBX=f000d2f6 ECX=00006cac EDX=000f8956
ESI=bffbdf62 EDI=00000000 EBP=00006c68 ESP=00006c68
EIP=0000d187 EFL=00000004 [-----P-] CPL=0 II=0 A20=1 SMM=0 HLT=0
ES =e000 000e0000 ffffffff 00809300 DPL=0 DS16 [-WA]
CS =f000 000f0000 ffffffff 00809b00 DPL=0 CS16 [-RA]
SS =0000 00000000 ffffffff 00809300 DPL=0 DS16 [-WA]
DS =0000 00000000 ffffffff 00809300 DPL=0 DS16 [-WA]
FS =0000 00000000 ffffffff 00809300 DPL=0 DS16 [-WA]
GS =0000 00000000 ffffffff 00809300 DPL=0 DS16 [-WA]
LDT=0000 00000000 0000ffff 00008200 DPL=0 LDT
TR =0000 00000000 0000ffff 00008b00 DPL=0 TSS32-busy
GDT= 000f6a80 00000037
IDT= 000f6abe 00000000
CR0=00000011 CR2=00000000 CR3=00000000 CR4=00000000
DR0=0000000000000000 DR1=0000000000000000 DR2=0000000000000000 DR3=0000000000000000
DR6=00000000ffff0ff0 DR7=0000000000000400
EFER=0000000000000000
Code=01 1e b8 6a 2e 0f 01 16 74 6a 0f 20 c0 66 83 c8 01 0f 22 c0 <66> ea 8f d1 0f 00 08 00 b8 10 00 00 00 8e d8 8e c0 8e d0 8e e0 8e e8 89 c8 ff e2 89 c1 b8X
X86 eflags bit 1 is fixed set, which means that 1 << 1 is set instead of 1,
this patch fix it.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Message-Id: <1428473294-6633-1-git-send-email-wanpeng.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Regression in commit 2caa80e72b
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Feb 22 11:38:36 2015 +0100
drm: Fix deadlock due to getconnector locking changes
If the drm_connector_find() call returns NULL, we should no longer
call drm_modeset_unlock() to avoid locking imbalance.
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Simon reported the md io stats accounting issue:
"
I'm seeing "iostat -x -k 1" print this after a RAID1 rebuild on 4.0-rc5.
It's not abnormal other than it's 3-disk, with one being SSD (sdc) and
the other two being write-mostly:
Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await r_await w_await svctm %util
sda 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
sdb 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
sdc 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
md0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 345.00 0.00 0.00 0.00 0.00 100.00
md2 0.00 0.00 0.00 0.00 0.00 0.00 0.00 58779.00 0.00 0.00 0.00 0.00 100.00
md1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 12.00 0.00 0.00 0.00 0.00 100.00
"
The cause is commit "18c0b223cf9901727ef3b02da6711ac930b4e5d4" uses the
generic_start_io_acct to account the disk stats rather than the open code,
but it also introduced the increase to .in_flight[rw] which is needless to
md. So we re-use the open code here to fix it.
Reported-by: Simon Kirby <sim@hostway.ca>
Cc: <stable@vger.kernel.org> 3.19
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: NeilBrown <neilb@suse.de>
"The domainname can be specified as either a DNS host name, a
dotted-decimal IPv4 address, or a bracketed IPv6 address as specified
in [RFC2732]."
See https://bugzilla.redhat.com/show_bug.cgi?id=1206868
Reported-by: Kyle Brantley <kyle@averageurl.com>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Currently when a process accesses a hugetlb range protected with
PROTNONE, unexpected COWs are triggered, which finally puts the hugetlb
subsystem into a broken/uncontrollable state, where for example
h->resv_huge_pages is subtracted too much and wraps around to a very
large number, and the free hugepage pool is no longer maintainable.
This patch simply stops changing protection for vma(VM_HUGETLB) to fix
the problem. And this also allows us to avoid useless overhead of minor
faults.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Suggested-by: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: David Rientjes <rientjes@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dmapool uses struct device in function arguments but relies on an
implicit inclusion to declare struct device causing warnings in some
configurations:
include/linux/dmapool.h:31:7: warning: 'struct device' declared inside parameter list
Fix this by adding a struct device declaration to the file.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Huang Ying reported the following problem due to commit 3484b2de94 ("mm:
rearrange zone fields into read-only, page alloc, statistics and page
reclaim lines") from the Intel performance tests
24b7e5819a3484b2de94
---------------- --------------------------
%stddev %change %stddev
\ | \
152288 \261 0% -46.2% 81911 \261 0% aim7.jobs-per-min
237 \261 0% +85.6% 440 \261 0% aim7.time.elapsed_time
237 \261 0% +85.6% 440 \261 0% aim7.time.elapsed_time.max
25026 \261 0% +70.7% 42712 \261 0% aim7.time.system_time
2186645 \261 5% +32.0% 2885949 \261 4% aim7.time.voluntary_context_switches
4576561 \261 1% +24.9% 5715773 \261 0% aim7.time.involuntary_context_switches
The problem is specific to very large machines under stress. It was not
reproducible with the machines I had used to justify the original patch
because large numbers of CPUs are required. When pressure is high enough,
the cache line is bouncing between CPUs trying to acquire the lock and the
holder of the lock adjusting free lists. The intention was that the
acquirer of the lock would automatically have the cache line holding the
free lists but according to Huang, this is not a universal win.
One possibility is to move the zone lock to its own cache line but it
increases the size of the zone. This patch moves the lock to the other
end of the free lists where they do not contend under high pressure. It
does mean the page allocator paths now require more cache lines but Huang
reports that it restores performance to previous levels on large machines
%stddev %change %stddev
\ | \
84568 \261 1% +94.3% 164280 \261 1% aim7.jobs-per-min
2881944 \261 2% -35.1% 1870386 \261 8% aim7.time.voluntary_context_switches
681 \261 1% -3.4% 658 \261 0% aim7.time.user_time
5538139 \261 0% -12.1% 4867884 \261 0% aim7.time.involuntary_context_switches
44174 \261 1% -46.0% 23848 \261 1% aim7.time.system_time
426 \261 1% -48.4% 219 \261 1% aim7.time.elapsed_time
426 \261 1% -48.4% 219 \261 1% aim7.time.elapsed_time.max
468 \261 1% -43.1% 266 \261 2% uptime.boot
Signed-off-by: Mel Gorman <mgorman@suse.de>
Reported-by: Huang Ying <ying.huang@intel.com>
Tested-by: Huang Ying <ying.huang@intel.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simple patch to make symbols static. Symbols that are not
shared with other parts of the kernel can be made static.
This change also removes several sparse complains.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Ajit Pal Singh <ajitpal.singh@st.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Some temperature sensors only get updated every few seconds and while
waiting for the first irq reporting a (new) temperature to happen there
get_temp operand will return -EAGAIN as it does not have any data to report
yet.
Not logging an error in this case avoids messages like these from showing
up in dmesg on affected systems:
[ 1.219353] thermal thermal_zone0: failed to read out thermal zone 0
[ 2.015433] thermal thermal_zone0: failed to read out thermal zone 0
[ 2.416737] thermal thermal_zone0: failed to read out thermal zone 0
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
1. Assorted changes
1.1 allow more feature bits for the guest
1.2 Store breaking event address on program interrupts
2. Interrupt handling rework
2.1 Fix copy_to_user while holding a spinlock (cc stable)
2.2 Rework floating interrupts to follow the priorities
2.3 Allow to inject all local interrupts via new ioctl
2.4 allow to get/set the full local irq state, e.g. for migration
and introspection
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=Rrx5
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-20150331' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
Features and fixes for 4.1 (kvm/next)
1. Assorted changes
1.1 allow more feature bits for the guest
1.2 Store breaking event address on program interrupts
2. Interrupt handling rework
2.1 Fix copy_to_user while holding a spinlock (cc stable)
2.2 Rework floating interrupts to follow the priorities
2.3 Allow to inject all local interrupts via new ioctl
2.4 allow to get/set the full local irq state, e.g. for migration
and introspection
This reverts commit 89baaa570a.
Dirty page throttling should be sufficient for us in the general case
so there is no need to use __GFP_MEMALLOC - it would be needed only in
the swap-over-rbd case, which we currently don't support. (It would
probably take approximately the commit that is being reverted to add
that support, but we would also need the "swap" option to distinguish
from the general case and make sure swap ceph_client-s aren't shared
with anything else.) See ceph-devel threads [1] and [2] for the
details of why enabling pfmemalloc reserves for all cases is a bad
thing.
On top of potential system lockups related to drained emergency
reserves, this turned out to cause ceph lockups in case peers are on
the same host and communicating via loopback due to sk_filter()
dropping pfmemalloc skbs on the receiving side because the receiving
loopback socket is not tagged with SOCK_MEMALLOC.
[1] "SOCK_MEMALLOC vs loopback"
http://www.spinics.net/lists/ceph-devel/msg22998.html
[2] "[PATCH] libceph: don't set memalloc flags in loopback case"
http://www.spinics.net/lists/ceph-devel/msg23392.html
Conflicts:
net/ceph/messenger.c [ context: tcp_nodelay option ]
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Sage Weil <sage@redhat.com>
Cc: stable@vger.kernel.org # 3.18+, needs backporting
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Mel Gorman <mgorman@suse.de>
Fixes page refcounting issues in our Stage-2 page table management code,
fixes a missing unlock in a gicv3 error path, and fixes a race that can
cause lost interrupts if signals are pending just prior to entering the
guest.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVBs95AAoJEEtpOizt6ddyAfoH/Rwj2T38ZDikImPpgfeFrmJs
ZlWC+Z3akwjVHPv308/MsKdyashtA7OjiMp3DOheMFMYJay/ecgY/92vFCc6uh5S
LDoXCbp+Pneth6C6bbU2Gw+aoCD07ZYCn9PeFq40MfpQUhCEGWhx41OFzHppqOZx
e+jodHRE+sBVTFUtbz+HubAfcM46f/8bP7682CEKsVZPeTSiHyeojdZEglfB37MG
ar/iC1/cyO/097vWaBqv1t1WZoHbWmMrDlzo5X+AtayVXFNdv4Ztw0Rz2kRhnLB8
8GXYawoSQoTN8FX1oyTyr5YWcWD7wDTzhcHsHS1xZHhvrdLCEcFrHeEWkuUlYjU=
=YS6j
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-fixes-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into 'kvm-next'
Fixes for KVM/ARM for 4.0-rc5.
Fixes page refcounting issues in our Stage-2 page table management code,
fixes a missing unlock in a gicv3 error path, and fixes a race that can
cause lost interrupts if signals are pending just prior to entering the
guest.
Looks like it was introduced in:
commit 650ad970a3
Author: Imre Deak <imre.deak@intel.com>
Date: Fri Apr 18 16:35:02 2014 +0300
drm/i915: vlv: factor out vlv_force_gfx_clock and check for pending force-of
but I'm not sure why. It has caused problems for us in the past (see
85250ddff7 "drm/i915/chv: Remove Wait for a previous gfx force-off"
and 8d4eee9cd7 "drm/i915: vlv: increase timeout when forcing on the
GFX clock") and doesn't seem to be required, so let's just drop it.
References: https://bugs.freedesktop.org/show_bug.cgi?id=89611
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Cc: stable@vger.kernel.org # c9c52e2419: drm/i915/chv: Remove Wait ...
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
On CHV, PUNIT team confirmed that 'VLV_GFX_CLK_STATUS_BIT' is not a
sticky bit and it will always be set. So ignore Check for previous
Gfx force off during suspend and allow the force clk as part S0ix
Sequence
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Some BIOSes (e.g. the one on the Minnowboard) don't save/restore this
reg. If it's unlocked, we can just restore the previous value, and if
it's locked (in case the BIOS re-programmed it for us) the write will be
ignored and we'll still have "did it move" sanity check in the PM code to
warn us if something is still amiss.
References: https://bugs.freedesktop.org/show_bug.cgi?id=89611
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Darren Hart <dvhart@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Commit 84c91b7ae0 (PM / hibernate: avoid unsafe pages in e820 reserved
regions) is reported to make resume from hibernation on Lenovo x230
unreliable, so revert it.
We will revisit the issue the commit in question was supposed to fix
in the future.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=96111
Reported-by: rhn <kebuac.rhn@porcupinefactory.org>
Cc: 3.17+ <stable@vger.kernel.org> # 3.17+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull networking fixes from David Miller:
1) In TCP, don't register an FRTO for cumulatively ACK'd data that was
previously SACK'd, from Neal Cardwell.
2) Need to hold RNL mutex in ipv4 multicast code namespace cleanup,
from Cong WANG.
3) Similarly we have to hold RNL mutex for fib_rules_unregister(), also
from Cong WANG.
4) Revert and rework netns nsid allocation fix, from Nicolas Dichtel.
5) When we encapsulate for a tunnel device, skb->sk still points to the
user socket. So this leads to cases where we retraverse the
ipv4/ipv6 output path with skb->sk being of some other address
family (f.e. AF_PACKET). This can cause things to crash since the
ipv4 output path is dereferencing an AF_PACKET socket as if it were
an ipv4 one.
The short term fix for 'net' and -stable is to elide these socket
checks once we've entered an encapsulation sequence by testing
xmit_recursion.
Longer term we have a better solution wherein we pass the tunnel's
socket down through the output paths, but that is way too invasive
for 'net' and -stable.
From Hannes Frederic Sowa.
6) l2tp_init() failure path forgets to unregister per-net ops, from
Cong WANG.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net/mlx4_core: Fix error message deprecation for ConnectX-2 cards
net: dsa: fix filling routing table from OF description
l2tp: unregister l2tp_net_ops on failure path
mvneta: dont call mvneta_adjust_link() manually
ipv6: protect skb->sk accesses from recursive dereference inside the stack
netns: don't allocate an id for dead netns
Revert "netns: don't clear nsid too early on removal"
ip6mr: call del_timer_sync() in ip6mr_free_table()
net: move fib_rules_unregister() under rtnl lock
ipv4: take rtnl_lock and mark mrt table as freed on namespace cleanup
tcp: fix FRTO undo on cumulative ACK of SACKed range
xen-netfront: transmit fully GSO-sized packets
If we fail past the aio_setup_ring(), we need to destroy the
mapping. We don't need to care about anybody having found ctx,
or added requests to it, since the last failure exit is exactly
the failure to make ctx visible to lookups.
Reproducer (based on one by Joe Mario <jmario@redhat.com>):
void count(char *p)
{
char s[80];
printf("%s: ", p);
fflush(stdout);
sprintf(s, "/bin/cat /proc/%d/maps|/bin/fgrep -c '/[aio] (deleted)'", getpid());
system(s);
}
int main()
{
io_context_t *ctx;
int created, limit, i, destroyed;
FILE *f;
count("before");
if ((f = fopen("/proc/sys/fs/aio-max-nr", "r")) == NULL)
perror("opening aio-max-nr");
else if (fscanf(f, "%d", &limit) != 1)
fprintf(stderr, "can't parse aio-max-nr\n");
else if ((ctx = calloc(limit, sizeof(io_context_t))) == NULL)
perror("allocating aio_context_t array");
else {
for (i = 0, created = 0; i < limit; i++) {
if (io_setup(1000, ctx + created) == 0)
created++;
}
for (i = 0, destroyed = 0; i < created; i++)
if (io_destroy(ctx[i]) == 0)
destroyed++;
printf("created %d, failed %d, destroyed %d\n",
created, limit - created, destroyed);
count("after");
}
}
Found-by: Joe Mario <jmario@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
teach ->mremap() method to return an error and have it fail for
aio mappings in process of being killed
Note that in case of ->mremap() failure we need to undo move_page_tables()
we'd already done; we could call ->mremap() first, but then the failure of
move_page_tables() would require undoing whatever _successful_ ->mremap()
has done, which would be a lot more headache in general.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Commit 1daa4303b4 ("net/mlx4_core: Deprecate error message at
ConnectX-2 cards startup to debug") did the deprecation only for port 1
of the card. Need to deprecate for port 2 as well.
Fixes: 1daa4303b4 ("net/mlx4_core: Deprecate error message at ConnectX-2 cards startup to debug")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to description in 'include/net/dsa.h', in cascade switches
configurations where there are more than one interconnected devices,
'rtable' array in 'dsa_chip_data' structure is used to indicate which
port on this switch should be used to send packets to that are destined
for corresponding switch.
However, dsa_of_setup_routing_table() fills 'rtable' with port numbers
of the _target_ switch, but not current one.
This commit removes redundant devicetree parsing and adds needed port
number as a function argument. So dsa_of_setup_routing_table() now just
looks for target switch number by parsing parent of 'link' device node.
To remove possible misunderstandings with the way of determining target
switch number, a corresponding comment was added to the source code and
to the DSA device tree bindings documentation file.
This was tested on a custom board with two Marvell 88E6095 switches with
following corresponding routing tables: { -1, 10 } and { 8, -1 }.
Signed-off-by: Pavel Nakonechny <pavel.nakonechny@skitlab.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull input fixes from Dmitry Torokhov:
"Updates for the input subsystem - two more tweaks for ALPS driver to
work out kinks after splitting the touchpad, trackstick, and potential
external PS/2 mouse into separate input devices.
Changes to support ALPS SS4 devices (protocol V8) will be coming in
4.1..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: alps - document stick behavior for protocol V2
Input: alps - report V2 Dualpoint Stick events via the right evdev node
Input: alps - report interleaved bare PS/2 packets via dev3
mvneta_adjust_link() is a callback for of_phy_connect() and should
not be called directly. The result of calling it directly is as below:
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not consult skb->sk for output decisions in xmit recursion
levels > 0 in the stack. Otherwise local socket settings could influence
the result of e.g. tunnel encapsulation process.
ipv6 does not conform with this in three places:
1) ip6_fragment: we do consult ipv6_npinfo for frag_size
2) sk_mc_loop in ipv6 uses skb->sk and checks if we should
loop the packet back to the local socket
3) ip6_skb_dst_mtu could query the settings from the user socket and
force a wrong MTU
Furthermore:
In sk_mc_loop we could potentially land in WARN_ON(1) if we use a
PF_PACKET socket ontop of an IPv6-backed vxlan device.
Reuse xmit_recursion as we are currently only interested in protecting
tunnel devices.
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document that protocol V2 uses standard (bare) PS/2 mouse packets for the
DualPoint stick.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-By: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
