Currently one resolves the location of the reserved_ttbr0 for PAN by
taking a positive offset from swapper_pg_dir. In a future patch we wish
to extend the swapper s.t. its size is determined at link time rather
than comile time, rendering SWAPPER_DIR_SIZE unsuitable for such a low
level calculation.
In this patch we re-arrange the order of the linker script s.t. instead
one computes reserved_ttbr0 by subtracting RESERVED_TTBR0_SIZE from
swapper_pg_dir.
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When CONFIG_UNMAP_KERNEL_AT_EL0 is set the SDEI entry point and the rest
of the kernel may be unmapped when we take an event. If this may be the
case, use an entry trampoline that can switch to the kernel page tables.
We can't use the provided PSTATE to determine whether to switch page
tables as we may have interrupted the kernel's entry trampoline, (or a
normal-priority event that interrupted the kernel's entry trampoline).
Instead test for a user ASID in ttbr1_el1.
Save a value in regs->addr_limit to indicate whether we need to restore
the original ASID when returning from this event. This value is only used
by do_page_fault(), which we don't call with the SDEI regs.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
SDEI needs to calculate an offset in the trampoline page too. Move
the extern char[] to sections.h.
This patch just moves code around.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
SDEI inherits the 'use hvc' bit that is also used by PSCI. PSCI does all
its initialisation early, SDEI does its late.
Remove the __init annotation from acpi_psci_use_hvc().
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The Software Delegated Exception Interface (SDEI) is an ARM standard
for registering callbacks from the platform firmware into the OS.
This is typically used to implement RAS notifications.
Such notifications enter the kernel at the registered entry-point
with the register values of the interrupted CPU context. Because this
is not a CPU exception, it cannot reuse the existing entry code.
(crucially we don't implicitly know which exception level we interrupted),
Add the entry point to entry.S to set us up for calling into C code. If
the event interrupted code that had interrupts masked, we always return
to that location. Otherwise we pretend this was an IRQ, and use SDEI's
complete_and_resume call to return to vbar_el1 + offset.
This allows the kernel to deliver signals to user space processes. For
KVM this triggers the world switch, a quick spin round vcpu_run, then
back into the guest, unless there are pending signals.
Add sdei_mask_local_cpu() calls to the smp_send_stop() code, this covers
the panic() code-path, which doesn't invoke cpuhotplug notifiers.
Because we can interrupt entry-from/exit-to another EL, we can't trust the
value in sp_el0 or x29, even if we interrupted the kernel, in this case
the code in entry.S will save/restore sp_el0 and use the value in
__entry_task.
When we have VMAP stacks we can interrupt the stack-overflow test, which
stirs x0 into sp, meaning we have to have our own VMAP stacks. For now
these are allocated when we probe the interface. Future patches will add
refcounting hooks to allow the arch code to allocate them lazily.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Today the arm64 arch code allocates an extra IRQ stack per-cpu. If we
also have SDEI and VMAP stacks we need two extra per-cpu VMAP stacks.
Move the VMAP stack allocation out to a helper in a new header file.
This avoids missing THREADINFO_GFP, or getting the all-important alignment
wrong.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The Software Delegated Exception Interface (SDEI) is an ARM standard
for registering callbacks from the platform firmware into the OS.
This is typically used to implement firmware notifications (such as
firmware-first RAS) or promote an IRQ that has been promoted to a
firmware-assisted NMI.
Add the code for detecting the SDEI version and the framework for
registering and unregistering events. Subsequent patches will add the
arch-specific backend code and the necessary power management hooks.
Only shared events are supported, power management, private events and
discovery for ACPI systems will be added by later patches.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that a VHE host uses tpidr_el2 for the cpu offset we no longer
need KVM to save/restore tpidr_el1. Move this from the 'common' code
into the non-vhe code. While we're at it, on VHE we don't need to
save the ELR or SPSR as kernel_entry in entry.S will have pushed these
onto the kernel stack, and will restore them from there. Move these
to the non-vhe code as we need them to get back to the host.
Finally remove the always-copy-tpidr we hid in the stage2 setup
code, cpufeature's enable callback will do this for VHE, we only
need KVM to do it for non-vhe. Add the copy into kvm-init instead.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that KVM uses tpidr_el2 in the same way as Linux's cpu_offset in
tpidr_el1, merge the two. This saves KVM from save/restoring tpidr_el1
on VHE hosts, and allows future code to blindly access per-cpu variables
without triggering world-switch.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Make tpidr_el2 a cpu-offset for per-cpu variables in the same way the
host uses tpidr_el1. This lets tpidr_el{1,2} have the same value, and
on VHE they can be the same register.
KVM calls hyp_panic() when anything unexpected happens. This may occur
while a guest owns the EL1 registers. KVM stashes the vcpu pointer in
tpidr_el2, which it uses to find the host context in order to restore
the host EL1 registers before parachuting into the host's panic().
The host context is a struct kvm_cpu_context allocated in the per-cpu
area, and mapped to hyp. Given the per-cpu offset for this CPU, this is
easy to find. Change hyp_panic() to take a pointer to the
struct kvm_cpu_context. Wrap these calls with an asm function that
retrieves the struct kvm_cpu_context from the host's per-cpu area.
Copy the per-cpu offset from the hosts tpidr_el1 into tpidr_el2 during
kvm init. (Later patches will make this unnecessary for VHE hosts)
We print out the vcpu pointer as part of the panic message. Add a back
reference to the 'running vcpu' in the host cpu context to preserve this.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
KVM uses tpidr_el2 as its private vcpu register, which makes sense for
non-vhe world switch as only KVM can access this register. This means
vhe Linux has to use tpidr_el1, which KVM has to save/restore as part
of the host context.
If the SDEI handler code runs behind KVMs back, it mustn't access any
per-cpu variables. To allow this on systems with vhe we need to make
the host use tpidr_el2, saving KVM from save/restoring it.
__guest_enter() stores the host_ctxt on the stack, do the same with
the vcpu.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Setting si_code to 0 results in a userspace seeing an si_code of 0.
This is the same si_code as SI_USER. Posix and common sense requires
that SI_USER not be a signal specific si_code. As such this use of 0
for the si_code is a pretty horribly broken ABI.
Further use of si_code == 0 guaranteed that copy_siginfo_to_user saw a
value of __SI_KILL and now sees a value of SIL_KILL with the result
that uid and pid fields are copied and which might copying the si_addr
field by accident but certainly not by design. Making this a very
flakey implementation.
Utilizing FPE_FIXME, BUS_FIXME, TRAP_FIXME siginfo_layout will now return
SIL_FAULT and the appropriate fields will be reliably copied.
But folks this is a new and unique kind of bad. This is massively
untested code bad. This is inventing new and unique was to get
siginfo wrong bad. This is don't even think about Posix or what
siginfo means bad. This is lots of eyeballs all missing the fact
that the code does the wrong thing bad. This is getting stuck
and keep making the same mistake bad.
I really hope we can find a non userspace breaking fix for this on a
port as new as arm64.
Possible ABI fixes include:
- Send the signal without siginfo
- Don't generate a signal
- Possibly assign and use an appropriate si_code
- Don't handle cases which can't happen
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Tyler Baicar <tbaicar@codeaurora.org>
Cc: James Morse <james.morse@arm.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Nicolas Pitre <nico@linaro.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arm-kernel@lists.infradead.org
Ref: 53631b54c8 ("arm64: Floating point and SIMD")
Ref: 32015c2356 ("arm64: exception: handle Synchronous External Abort")
Ref: 1d18c47c73 ("arm64: MMU fault handling and page table management")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
When replacing the cpm by cp0 and cps by cp1 [1] not only the label and
the alias were replaced but also the compatible string which was wrong.
Due to this the pinctrl driver was no more probed.
This patch fix it by reverting this change for the pinctrl compatible
string on Armada 8K.
[1]: "arm64: dts: marvell: replace cpm by cp0, cps by cp1"
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Support for the Cluster PMU part of the ARM DynamIQ Shared Unit (DSU).
* 'for-next/perf' of git://git.kernel.org/pub/scm/linux/kernel/git/will/linux:
perf: ARM DynamIQ Shared Unit PMU support
dt-bindings: Document devicetree binding for ARM DSU PMU
arm_pmu: Use of_cpu_node_to_id helper
arm64: Use of_cpu_node_to_id helper for CPU topology parsing
irqchip: gic-v3: Use of_cpu_node_to_id helper
coresight: of: Use of_cpu_node_to_id helper
of: Add helper for mapping device node to logical CPU number
perf: Export perf_event_update_userpage
Choose to compile and embed marvell_nand.c as NAND controller driver
instead of the legacy pxa3xx_nand.c for platforms with Marvell EBU
SoCs.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We need to consistently enforce that keyed hashes cannot be used without
setting the key. To do this we need a reliable way to determine whether
a given hash algorithm is keyed or not. AF_ALG currently does this by
checking for the presence of a ->setkey() method. However, this is
actually slightly broken because the CRC-32 algorithms implement
->setkey() but can also be used without a key. (The CRC-32 "key" is not
actually a cryptographic key but rather represents the initial state.
If not overridden, then a default initial state is used.)
Prepare to fix this by introducing a flag CRYPTO_ALG_OPTIONAL_KEY which
indicates that the algorithm has a ->setkey() method, but it is not
required to be called. Then set it on all the CRC-32 algorithms.
The same also applies to the Adler-32 implementation in Lustre.
Also, the cryptd and mcryptd templates have to pass through the flag
from their underlying algorithm.
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
dtc complains about the lack of #coolin-cells properties for the
CPU nodes that are referred to as "cooling-device":
arch/arm64/boot/dts/mediatek/mt8173-evb.dtb: Warning (cooling_device_property): Missing property '#cooling-cells' in node /cpus/cpu@0 or bad phandle (referred from /thermal-zones/cpu_thermal/cooling-maps/map@0:cooling-device[0])
arch/arm64/boot/dts/mediatek/mt8173-evb.dtb: Warning (cooling_device_property): Missing property '#cooling-cells' in node /cpus/cpu@100 or bad phandle (referred from /thermal-zones/cpu_thermal/cooling-maps/map@1:cooling-device[0])
Apparently this property must be '<2>' to match the binding.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The PMU node has no working interrupt, as shown by this dtc warning:
arch/arm64/boot/dts/altera/socfpga_stratix10_socdk.dtb: Warning (interrupts_property): Missing interrupt-parent for /pmu
This adds an interrupt-parent property so we can correct parse
that interrupt number.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
2 device tree related fixes fixing 2 issues:
- broken pinctrl support since 4.11 on OpenBlocks A7
- implicit clock dependency making the kernel hang if the Xenon sdhci
module was loaded before the mvpp2 Ethernet support (for this one
the driver had to be fixed which was done in v4.14)
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWk+glCMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71Zt+AJ9ozVoJfwdf
79od8wlcB4PUvHb6FgCgqkH7FXqfkpHLdFYm8E9GRlj6nVY=
=9vZv
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.15-1' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixess for 4.15 (part 1)
2 device tree related fixes fixing 2 issues:
- broken pinctrl support since 4.11 on OpenBlocks A7
- implicit clock dependency making the kernel hang if the Xenon sdhci
module was loaded before the mvpp2 Ethernet support (for this one
the driver had to be fixed which was done in v4.14)
* tag 'mvebu-fixes-4.15-1' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: armada-cp110: Fix clock resources for various node
ARM: dts: kirkwood: fix pin-muxing of MPP7 on OpenBlocks A7
Signed-off-by: Olof Johansson <olof@lixom.net>
A few improvements to our DT support, with:
- basic DRM support for the A83t
- simplefb support for the H3 and H5 SoCs
- One fix for the USB ethernet on the Orange Pi R1
-----BEGIN PGP SIGNATURE-----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=bDG2
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.16, bis
A few improvements to our DT support, with:
- basic DRM support for the A83t
- simplefb support for the H3 and H5 SoCs
- One fix for the USB ethernet on the Orange Pi R1
* tag 'sunxi-dt-for-4.16-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a711: Enable the LCD
ARM: dts: sun8i: a83t: Add LVDS pins group
ARM: dts: sun8i: a83t: Enable the PWM
ARM: dts: sun8i: a83t: Add display pipeline
ARM: sunxi: h3/h5: add simplefb nodes
arm64: allwinner: h5: add compatible string for DE2 CCU
ARM: sun8i: h3/h5: add DE2 CCU device node for H3
dt-bindings: simplefb-sunxi: add pipelines for DE2
ARM: dts: sun8i: fix USB Ethernet of Orange Pi R1
Signed-off-by: Olof Johansson <olof@lixom.net>
include IR, SPI and ethernet MAC support for the new AXG family SoCs.
-----BEGIN PGP SIGNATURE-----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=lk2H
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt64-3' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Another round of 64-bit DT changes for the new Amlogic SoCs. These
include IR, SPI and ethernet MAC support for the new AXG family SoCs.
* tag 'amlogic-dt64-3' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-axg: enable ethernet for A113D S400 board
ARM64: dts: meson-axg: add ethernet mac controller
ARM64: dts: meson-axg: add the SPICC controller
ARM64: dts: meson-axg: enable IR controller
arm64: dts: meson-axg: switch uart_ao clock to CLK81
clk: meson-axg: add clocks dt-bindings required header
dt-bindings: clock: add compatible variant for the Meson-AXG
Signed-off-by: Olof Johansson <olof@lixom.net>
And unlike the other helpers we don't require a <asm/dma-direct.h> as
this helper is a special case for ia64 only, and this keeps it as
simple as possible.
Signed-off-by: Christoph Hellwig <hch@lst.de>
phys_to_dma, dma_to_phys and dma_capable are helpers published by
architecture code for use of swiotlb and xen-swiotlb only. Drivers are
not supposed to use these directly, but use the DMA API instead.
Move these to a new asm/dma-direct.h helper, included by a
linux/dma-direct.h wrapper that provides the default linear mapping
unless the architecture wants to override it.
In the MIPS case the existing dma-coherent.h is reused for now as
untangling it will take a bit of work.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Robin Murphy <robin.murphy@arm.com>
The generic version now takes dma_pfn_offset into account, so there is no
more need for an architecture override.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Construct the init thread stack in the linker script rather than doing it
by means of a union so that ia64's init_task.c can be got rid of.
The following symbols are then made available from INIT_TASK_DATA() linker
script macro:
init_thread_union
init_stack
INIT_TASK_DATA() also expands the region to THREAD_SIZE to accommodate the
size of the init stack. init_thread_union is given its own section so that
it can be placed into the stack space in the right order. I'm assuming
that the ia64 ordering is correct and that the task_struct is first and the
thread_info second.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Tested-by: Will Deacon <will.deacon@arm.com> (arm64)
Tested-by: Palmer Dabbelt <palmer@sifive.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Add an extra temporary register parameter to uaccess_ttbr0_enable which
is about to be required for arm64 PAN support.
This patch doesn't introduce any functional change but ensures that the
kernel compiles once the KVM/ARM tree is merged with the arm64 tree by
ensuring a trivially mergable conflict with commit
27a921e757
("arm64: mm: Fix and re-enable ARM64_SW_TTBR0_PAN").
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Use new binding about USB wakeup which now supports multi USB
wakeup glue layer between SSUSB and SPM.
Meanwhile remove dummy clocks of USB wakeup.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can just pass this on instead of having to do a radix tree lookup
without proper locking a few levels into the callchain.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We can just pass this on instead of having to do a radix tree lookup
without proper locking a few levels into the callchain.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add the older Broadcom ID as well as the new Cavium ID for ThunderX2
CPUs.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Falkor is susceptible to branch predictor aliasing and can
theoretically be attacked by malicious code. This patch
implements a mitigation for these attacks, preventing any
malicious entries from affecting other victim contexts.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
[will: fix label name when !CONFIG_KVM and remove references to MIDR_FALKOR]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cortex-A57, A72, A73 and A75 are susceptible to branch predictor aliasing
and can theoretically be attacked by malicious code.
This patch implements a PSCI-based mitigation for these CPUs when available.
The call into firmware will invalidate the branch predictor state, preventing
any malicious entries from affecting other victim contexts.
Co-developed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Hook up MIDR values for the Cortex-A72 and Cortex-A75 CPUs, since they
will soon need MIDR matches for hardening the branch predictor.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
For those CPUs that require PSCI to perform a BP invalidation,
going all the way to the PSCI code for not much is a waste of
precious cycles. Let's terminate that call as early as possible.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that we have per-CPU vectors, let's plug then in the KVM/arm64 code.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Aliasing attacks against CPU branch predictors can allow an attacker to
redirect speculative control flow on some CPUs and potentially divulge
information from one context to another.
This patch adds initial skeleton code behind a new Kconfig option to
enable implementation-specific mitigations against these attacks for
CPUs that are affected.
Co-developed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We will soon need to invoke a CPU-specific function pointer after changing
page tables, so move post_ttbr_update_workaround out into C code to make
this possible.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In order to invoke the CPU capability ->matches callback from the ->enable
callback for applying local-CPU workarounds, we need a handle on the
capability structure.
This patch passes a pointer to the capability structure to the ->enable
callback.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
For non-KASLR kernels where the KPTI behaviour has not been overridden
on the command line we can use ID_AA64PFR0_EL1.CSV3 to determine whether
or not we should unmap the kernel whilst running at EL0.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Although CONFIG_UNMAP_KERNEL_AT_EL0 does make KASLR more robust, it's
actually more useful as a mitigation against speculation attacks that
can leak arbitrary kernel data to userspace through speculation.
Reword the Kconfig help message to reflect this, and make the option
depend on EXPERT so that it is on by default for the majority of users.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Speculation attacks against the entry trampoline can potentially resteer
the speculative instruction stream through the indirect branch and into
arbitrary gadgets within the kernel.
This patch defends against these attacks by forcing a misprediction
through the return stack: a dummy BL instruction loads an entry into
the stack, so that the predicted program flow of the subsequent RET
instruction is to a branch-to-self instruction which is finally resolved
as a branch to the kernel vectors with speculation suppressed.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The vcpu parameter isn't used for anything, and gets in the way of
further cleanups. Let's get rid of it.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
So far, we loose the Exec property whenever we take permission
faults, as we always reconstruct the PTE/PMD from scratch. This
can be counter productive as we can end-up with the following
fault sequence:
X -> RO -> ROX -> RW -> RWX
Instead, we can lookup the existing PTE/PMD and clear the XN bit in the
new entry if it was already cleared in the old one, leadig to a much
nicer fault sequence:
X -> ROX -> RWX
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
We've so far eagerly invalidated the icache, no matter how
the page was faulted in (data or prefetch abort).
But we can easily track execution by setting the XN bits
in the S2 page tables, get the prefetch abort at HYP and
perform the icache invalidation at that time only.
As for most VMs, the instruction working set is pretty
small compared to the data set, this is likely to save
some traffic (specially as the invalidation is broadcast).
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
As we're about to make S2 page-tables eXecute Never by default,
add the required bits for both PMDs and PTEs.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
We currently tightly couple dcache clean with icache invalidation,
but KVM could do without the initial flush to PoU, as we've
already flushed things to PoC.
Let's introduce invalidate_icache_range which is limited to
invalidating the icache from the linear mapping (and thus
has none of the userspace fault handling complexity), and
wire it in KVM instead of flush_icache_range.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
As we're about to introduce opportunistic invalidation of the icache,
let's split dcache and icache flushing.
Acked-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
kvm_hyp.h has an odd dependency on kvm_mmu.h, which makes the
opposite inclusion impossible. Let's start with breaking that
useless dependency.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Commit 0c0543a128 breaks migration and
introduces a regression with existing userspace because it introduces an
ordering requirement of setting up all VCPU features before writing ID
registers which we didn't have before.
Revert this commit for now until we have a proper fix.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
This is tested in the S400 dev board which use a RTL8211F PHY,
and the pins connect to the 'eth_rgmii_y_pins' group.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add DT info for the stmmac ethernet MAC which found in
the Amlogic's Meson-AXG SoC, also describe the ethernet
pinctrl & clock information here.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add DT info for the SPICC controller which found in
the Amlogic's Meson-AXG SoC.
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable IR remote controller which found in Amlogic's Meson-AXG SoCs.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Switch the uart_ao pclk to CLK81 since the clock driver is ready.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The main change here are the series of commits doing the Armada 7K/8K
CP110 DT de-duplication, they include the de-duplication itself and
small fixes in the device tree files.
Besides them there are 2 other patches:
- One adding the crypto support for Armada 37xx SoCs
- An other adding Ethernet aliases on A7K/A8K base boards
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWk+h0CMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71ZU9AKCNLcEcewii
UWPVUzEsQ/+UPojO4wCdHqum9OT33XChVrxHGKP89Dnj1ro=
=HCIC
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.16-2' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt64 for 4.16 (part 2)" from Gregory CLEMENT:
The main change here are the series of commits doing the Armada 7K/8K
CP110 DT de-duplication, they include the de-duplication itself and
small fixes in the device tree files.
Besides them there are 2 other patches:
- One adding the crypto support for Armada 37xx SoCs
- An other adding Ethernet aliases on A7K/A8K base boards
* tag 'mvebu-dt64-4.16-2' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: add Ethernet aliases
arm64: dts: marvell: replace cpm by cp0, cps by cp1
arm64: dts: marvell: de-duplicate CP110 description
arm64: dts: marvell: use aliases for SPI busses on Armada 7K/8K
arm64: dts: marvell: use mvebu-icu.h where possible
arm64: dts: marvell: fix compatible string list for Armada CP110 slave NAND
arm64: dts: marvell: fix typos in comment describing the NAND controller
arm64: dts: marvell: use lower case for unit address and reg property
arm64: dts: marvell: fix watchdog unit address in Armada AP806
arm64: dts: marvell: armada-37xx: add a crypto node
ARM64: dts: marvell: armada-cp110: Fix clock resources for various node
ARM: dts: kirkwood: fix pin-muxing of MPP7 on OpenBlocks A7
This patch adds Ethernet aliases in the Marvell Armada 7040 DB, 8040 DB
and 8040 mcbin device trees so that the bootloader setup the MAC
addresses correctly.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message, small fixes]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
In preparation for the introduction of more than 2 CPs in upcoming
SoCs, it makes sense to move away from the "CP master" (cpm) and "CP
slave" (cps) naming, and use instead cp0/cp1.
This commit is the result of:
sed 's%cpm%cp0g%' arch/arm64/boot/dts/marvell/*
sed 's%cps%cp1g%' arch/arm64/boot/dts/marvell/*
So it is a purely mechaninal change.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Suggested-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
One concept of Marvell Armada 7K/8K SoCs is that they are made of HW
blocks composed of a variety of IPs (network, PCIe, SATA, XOR, SPI,
I2C, etc.), and those HW blocks can be duplicated several times within
a given SoC. The Armada 7K SoC has a single CP110 (so no duplication),
while the Armada 8K SoC has two CP110. In the future, SoCs with more
than 2 CP110s will be introduced.
In current kernel versions, the master CP110 is described in
armada-cp110-master.dtsi and the slave CP110 is described in
armada-cp110-slave.dtsi. Those files are basically exactly the same,
since they describe the same hardware. They only have a few
differences:
- Base address of the registers is different for the "config-space"
- Base address of the PCIe registers, MEM, CONF and IO areas were
different
- Labels (and phandles pointing to them) of the nodes were different
("cpm" prefix in the master CP, "cps" prefix in the slave CP)
This duplication issue has been discussed at the DT workshop [1] in
Prague last October, and we presented on this topic [2]. The solution
of using the C pre-processor to avoid this duplication has been
validated by the people present in this DT workshop, and this patch
simply implements what has been presented.
We handle differences between the master CP and slave CP description
using the C pre-processor, by defining a set of macros with different
values armada-cp110.dtsi is included to instantiate one of the master
or slave CP110.
There are a few aspects that deserve additional explanations:
- PCIe needs to be handled separately because it is not part of the
config-space {...} node, since it has registers outside of the
range covered by config-space {...}.
- We need to defined CP110_BASE, CP110_PCIEx_BASE without 0x, because
they are used for the unit address part of some DT nodes. But since
they are also used for the "reg" property of the same nodes, we
have an ADDRESSIFY() macro that prepends 0x to those values.
We compared the resulting .dtb for armada-8040-db.dtb before and after
this patch is applied, and the result is exactly the same, except for
a few differences:
- the SDHCI controller that was only described in the master CP110 is
now also described in the slave CP110. Even though the SDHCI
controller from the slave CP110 is indeed not usable (as it isn't
wired to the outside world) it is technically part of the silicon,
and therefore it is reasonable to also describe it to be part of
the slave CP110. In addition, if we wanted to get this correct for
the SDHCI controller, we should also do it for the NAND controller,
for which the situation is even more complicated: in a single CP110
configuration (Armada 7K), the usable NAND controller is in the
master CP110, while in a dual CP110 configuration (Armada 8K), the
usable NAND controller is in the slave CP110. Since that would add
a lot of additional complexity for no good reason, and since the IP
blocks are in fact really present in both CPs, we simply describe
them in both CPs at the DT level.
- the cp110-master and cp110-slave nodes are now named cpm and
cps. We could have kept cp110-master and cp110-slave, but that
would have required adding another CP110_xyz define, which didn't
seem very useful.
Note that this commit also gets rid of the armada-cp110-master.dtsi
and armada-cp110-slave.dtsi files, as future SoCs will have more than
2 CPs. Instead, we instantiate the CPs directly from the SoC-specific
.dtsi files, i.e armada-70x0.dtsi and armada-80x0.dtsi.
[1] https://elinux.org/Device_tree_kernel_summit_2017_etherpad
[2] https://elinux.org/images/1/14/DTWorkshop2017-duplicate-data.pdf
[gregory.clement@free-electrons.com: add back the "ARM64: dts: marvell:
Fix clock resources for various node" commit]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
We are currently using the cell-index DT property to assign SPI bus
numbers. This property is specific to the spi-orion driver, and
requires each SPI controller to have a unique ID defined in the Device
Tree.
As we are about to merge armada-cp110-master.dtsi and
armada-cp110-slave.dtsi into a single file, those cell-index
properties that differ between the master CP110 and the slave CP110
are a difference that would have to be handled.
In order to avoid this, we switch to using the "aliases" DT node to
assign a unique number to each SPI controller. This is more generic,
and directly handled by the SPI core.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Back when the ICU Device Tree binding was introduced, we could not use
mvebu-icu.h from the Device Tree files, because the DT files and
mvebu-icu.h were following different merge routes towards Linus
tree. Now that both have been merged, we can switch the Marvell Armada
CP110 Device Tree files to use the mvebu-icu.h header instead of
duplicating the ICU_GRP_NSR definition.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada CP110 slave NAND controller Device Tree description lists
the compatible string in the wrong order: marvell,armada-8k-nand
should come first. This commit alignes the slave CP110 description
with the master CP110 description from that respect.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fix the same typo duplicated in both master and slave version of
armada-cp110-*.dtsi file: s/limiation/limitation/.
[gregory.clement@free-electrons.com: add the commit log]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This fixes the following DTC warning:
<stdout>: Warning (simple_bus_reg): Node /ap806/config-space@f0000000/thermal@6f808C simple-bus unit address format error, expected "6f808c"
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This fixes the following DTC warning:
Warning (simple_bus_reg): Node /ap806/config-space@f0000000/watchdog@600000 simple-bus unit address format error, expected "610000"
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds a crypto node describing the EIP97 engine found in
Armada 37xx SoCs. The cryptographic engine is enabled by default.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
On the CP modules we found on Armada 7K/8K, many IP block actually also
need a "functional" clock (from the bus). This patch add them which allows
to fix some issues hanging the kernel:
If Ethernet and sdhci driver are built as modules and sdhci was loaded
first then the kernel hang.
Fixes: bb16ea1742 ("mmc: sdhci-xenon: Fix clock resource by adding an
optional bus clock")
Cc: stable@vger.kernel.org
Reported-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
print_symbol() is a very old API that has been obsoleted by %pS format
specifier in a normal printk() call.
Replace print_symbol() with a direct printk("%pS") call.
Link: http://lkml.kernel.org/r/20171211125025.2270-3-sergey.senozhatsky@gmail.com
To: Andrew Morton <akpm@linux-foundation.org>
To: Russell King <linux@armlinux.org.uk>
To: Catalin Marinas <catalin.marinas@arm.com>
To: Mark Salter <msalter@redhat.com>
To: Tony Luck <tony.luck@intel.com>
To: David Howells <dhowells@redhat.com>
To: Yoshinori Sato <ysato@users.sourceforge.jp>
To: Guan Xuetao <gxt@mprc.pku.edu.cn>
To: Borislav Petkov <bp@alien8.de>
To: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To: Thomas Gleixner <tglx@linutronix.de>
To: Peter Zijlstra <peterz@infradead.org>
To: Vineet Gupta <vgupta@synopsys.com>
To: Fengguang Wu <fengguang.wu@intel.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-c6x-dev@linux-c6x.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-am33-list@redhat.com
Cc: linux-sh@vger.kernel.org
Cc: linux-edac@vger.kernel.org
Cc: x86@kernel.org
Cc: linux-snps-arc@lists.infradead.org
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
[pmladek@suse.com: updated commit message]
Signed-off-by: Petr Mladek <pmladek@suse.com>
ARM v8.4 extensions add new neon instructions for performing a
multiplication of each FP16 element of one vector with the corresponding
FP16 element of a second vector, and to add or subtract this without an
intermediate rounding to the corresponding FP32 element in a third vector.
This patch detects this feature and let the userspace know about it via a
HWCAP bit and MRS emulation.
Cc: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Dongjiu Geng <gengdongjiu@huawei.com>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Under some uncommon timing conditions, a generation check and
xchg(active_asids, A1) in check_and_switch_context() on P1 can race with
an ASID roll-over on P2. If P2 has not seen the update to
active_asids[P1], it can re-allocate A1 to a new task T2 on P2. P1 ends
up waiting on the spinlock since the xchg() returned 0 while P2 can go
through a second ASID roll-over with (T2,A1,G2) active on P2. This
roll-over copies active_asids[P1] == A1,G1 into reserved_asids[P1] and
active_asids[P2] == A1,G2 into reserved_asids[P2]. A subsequent
scheduling of T1 on P1 and T2 on P2 would match reserved_asids and get
their generation bumped to G3:
P1 P2
-- --
TTBR0.BADDR = T0
TTBR0.ASID = A0
asid_generation = G1
check_and_switch_context(T1,A1,G1)
generation match
check_and_switch_context(T2,A0,G0)
new_context()
ASID roll-over
asid_generation = G2
flush_context()
active_asids[P1] = 0
asid_map[A1] = 0
reserved_asids[P1] = A0,G0
xchg(active_asids, A1)
active_asids[P1] = A1,G1
xchg returns 0
spin_lock_irqsave()
allocated ASID (T2,A1,G2)
asid_map[A1] = 1
active_asids[P2] = A1,G2
...
check_and_switch_context(T3,A0,G0)
new_context()
ASID roll-over
asid_generation = G3
flush_context()
active_asids[P1] = 0
asid_map[A1] = 1
reserved_asids[P1] = A1,G1
reserved_asids[P2] = A1,G2
allocated ASID (T3,A2,G3)
asid_map[A2] = 1
active_asids[P2] = A2,G3
new_context()
check_update_reserved_asid(A1,G1)
matches reserved_asid[P1]
reserved_asid[P1] = A1,G3
updated T1 ASID to (T1,A1,G3)
check_and_switch_context(T2,A1,G2)
new_context()
check_and_switch_context(A1,G2)
matches reserved_asids[P2]
reserved_asids[P2] = A1,G3
updated T2 ASID to (T2,A1,G3)
At this point, we have two tasks, T1 and T2 both using ASID A1 with the
latest generation G3. Any of them is allowed to be scheduled on the
other CPU leading to two different tasks with the same ASID on the same
CPU.
This patch changes the xchg to cmpxchg so that the active_asids is only
updated if non-zero to avoid a race with an ASID roll-over on a
different CPU.
The ASID allocation algorithm has been formally verified using the TLA+
model checker (see
https://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/kernel-tla.git/tree/asidalloc.tla
for the spec).
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- clock, pinctrl, PWM and reset nodes for new AXG SoC family
-----BEGIN PGP SIGNATURE-----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=4k+i
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt64-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Pull "Amlogic 64-bit DT updates for v4.16, round 2" from Kevin Hilman:
This adds a few more basics (clock, pinctrl, PWM, reset) for the new AXG
family of Amlogic SoCs.
* tag 'amlogic-dt64-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson-axg: add new reset DT node
ARM64: dts: meson-axg: add PWM DT info for Meson-Axg SoC
ARM64: dts: meson-axg: add pinctrl DT info for Meson-AXG SoC
documentation: Add compatibles for Amlogic Meson AXG pin controllers
arm64: dts: meson-axg: add clock DT info for Meson AXG SoC
- clean up gpios properties by macro
- add GPIO hog for PXs3 reference node
- add has-transaction-translator property to generic-ehci nodes
- enable more serial ports for PXs3 reference node
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kgZ1
-----END PGP SIGNATURE-----
Merge tag 'uniphier-dt64-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt
UniPhier ARM64 SoC DT updates for v4.16
- clean up gpios properties by macro
- add GPIO hog for PXs3 reference node
- add has-transaction-translator property to generic-ehci nodes
- enable more serial ports for PXs3 reference node
* tag 'uniphier-dt64-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: enable more serial ports for PXs3 ref board
arm64: dts: uniphier: add has-transaction-translator property to usb node for LD11
arm64: dts: uniphier: add GPIO hog definition for PXs3
arm64: dts: uniphier: use macros in dt-bindings header
Signed-off-by: Olof Johansson <olof@lixom.net>
Enables MUSB driver and the Allwinner glue layer driver by default.
All Allwinner SoCs (excluding the A80) have the Mentor Graphics Inventra
Multi-Point Hi-Speed OTG Controller (MHDRC). Enabling this extends test
coverage to this peripheral.
-----BEGIN PGP SIGNATURE-----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=ykqf
-----END PGP SIGNATURE-----
Merge tag 'sunxi-config64-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/soc
Allwinner arm64 defconfig changes for 4.16
Enables MUSB driver and the Allwinner glue layer driver by default.
All Allwinner SoCs (excluding the A80) have the Mentor Graphics Inventra
Multi-Point Hi-Speed OTG Controller (MHDRC). Enabling this extends test
coverage to this peripheral.
* tag 'sunxi-config64-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: defconfig: enable MUSB HDRC along with Allwinner glue
Signed-off-by: Olof Johansson <olof@lixom.net>
There are two important changes in this round.
The first removes the redundant pinctrl setting for the MMC card detect
GPIO. We are moving to strict pinctrl/GPIO exclusion, i.e. GPIO usage
will block other pin muxing usage, and vice versa. The usage of pinmux
for guarding GPIO pins in the device tree prevents us from doing so.
This is part of an ongoing effort to clean up the existing device trees.
The other important change enables the PMIC on the Orangepi Win. The
PMIC provides power to most of the external onboard peripherals.
Enabling it will allow us to enable Ethernet or WiFi support later on.
The remaining changes in this round enable some peripheral, such as
Ethernet, an external WiFi chip, or LEDs.
-----BEGIN PGP SIGNATURE-----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=A9DZ
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT64 changes for 4.16
There are two important changes in this round.
The first removes the redundant pinctrl setting for the MMC card detect
GPIO. We are moving to strict pinctrl/GPIO exclusion, i.e. GPIO usage
will block other pin muxing usage, and vice versa. The usage of pinmux
for guarding GPIO pins in the device tree prevents us from doing so.
This is part of an ongoing effort to clean up the existing device trees.
The other important change enables the PMIC on the Orangepi Win. The
PMIC provides power to most of the external onboard peripherals.
Enabling it will allow us to enable Ethernet or WiFi support later on.
The remaining changes in this round enable some peripheral, such as
Ethernet, an external WiFi chip, or LEDs.
* tag 'sunxi-dt64-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: bananapi-m64: Add LED device node
arm64: dts: a64-olinuxino: Enable RTL8723BS WiFi
arm64: dts: allwinner: h5: NanoPi NEO Plus2 : add EMAC support
arm64: dts: allwinner: H5: remove redundant MMC0 card detect pin
arm64: allwinner: a64: Enable AXP803 for Orangepi Win
arm64: dts: orange-pi-zero-plus2: enable AP6212a WiFi/BT combo
Signed-off-by: Olof Johansson <olof@lixom.net>
Adding the cpu frequency scaling support for Armada 37xx
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWjzhHyMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71WygAJ9poqfM0F76
GCywSaql9D//YLIMBwCggBJU4OCJCgNJx/KN9n0+WmaM65M=
=D4Xs
-----END PGP SIGNATURE-----
Merge tag 'mvebu-arm64-4.16-1' of git://git.infradead.org/linux-mvebu into next/soc
mvebu arm64 for 4.16 (part 1)
Adding the cpu frequency scaling support for Armada 37xx
* tag 'mvebu-arm64-4.16-1' of git://git.infradead.org/linux-mvebu:
arm64: defconfig: enable ARM_ARMADA_37XX_CPUFREQ
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the NAND support on the Marvell 8040-DB board
Add the thermal support for Martvell A7K/A8K Socs
Add nodes allowing cpufreq support on Aramda 3700 SoCs
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWjzjGiMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71eRxAKCkcg3nYB1F
MLYZ5pQg0SA8p8IOPwCfczw9Uui9xxSaMnEjBgcDOZnkoSo=
=9aGc
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.16-1' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt64 for 4.16 (part 1)
Add the NAND support on the Marvell 8040-DB board
Add the thermal support for Martvell A7K/A8K Socs
Add nodes allowing cpufreq support on Aramda 3700 SoCs
* tag 'mvebu-dt64-4.16-1' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: Add thermal support for A7K/A8K
arm64: dts: marvell: armada-37xx: add nodes allowing cpufreq support
arm64: dts: marvell: add NAND support on the 8040-DB board
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add usb3_phy node to r8a7795 (R-Car H3) and r8a7796 (R-Car M3-W) SoCs, and
enable usb3_peri0 on salvator boards
* Allow DTBs of boards of r8a7795 (R-Car H3) and r8a7796 SoCs to build
without any warnings when compiled with W=1 using gcc-linaro-5.4.1-2017.05
- Move nodes which have no reg property out of bus, they don't belong there
- Add reg properties to dummy pciec[01] nodes
- Also sort sub-nodes of root node to allow for easier maintenance
* Add Add EthernetAVB PHY reset to r8a7795 (R-Car H3) and r8a7796 SoCs boards.
Geert Uytterhoeven says "... add properties to describe the EthernetAVB
PHY reset topology to the common Salvator-X/XS and ULCB DTS files, which
solves two issues:
1. On Salvator-XS, the enable pin of the regulator providing PHY power
is connected to PRESETn, and PSCI powers down the SoC during system
suspend. Hence a PHY reset is needed to restore network
functionality after system resume.
2. Linux should not rely on the boot loader having reset the PHY, but
should reset the PHY during driver probe."
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE4nzZofWswv9L/nKF189kaWo3T74FAlo813MACgkQ189kaWo3
T758mg//Zk+Xd+T0i1baVHduBM5DkmwchYXHzRnG2/1fGoLhOt5FJn1uJ4M1Hxog
q1b3c//PvYk7OIW36jRy/LS0tHYXkizVviSHlUrmNNuXP+EhhKFQGnmxuRNKjzi8
F8Kdi1xWs/R9a9uFczwDobXPg4spguk5qgEnbVVkmSuw3uN8ChPOVaGBPraeNzai
rIqhNkv8k2Lc3ReheRqgH0XiQBMi4/nvSbEFjOFbn4N7oiVJ6MqUBauzK4J+I2AB
5Y3uuE83nQhbNXwyit9AO0iix8Aob3XMCvpP5kEz3mgBJfjFMMDwIZ9W2pAWIG6G
g9axnPXloj8bXYQd0kppWlJihQu1Ufhn4z14UW7XCmQOHkXWwLKflYMEHORVx4TP
IAxjLHFlWUiJ9yvPNvE5PPjNjiovzKsZbjxR9r9Jy9oLgPcxgQk94hNbB2K1DTbK
tlxi75yyrVHhJaEZQk6Ev2tBAYHBB04uPrGVSdThmzssAInqd9lLyOrMtMOP/5ti
ZXOl8h87uK/zigBloCtfC/+GXUUIeOoZXC31m/nEhhvi2ST3QrXAoIcVCrzO25AB
f98vaGMGK2nmcNQB80oOdttFm/f0Jv131BokMwJzMInnM5DQsOJM8HAPZTaL0H3I
G3OaE6LJ/toKlKe6Eyb850WT6Xhv6hv/HbeiLAcip08w60GHyRM=
=L57U
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-dt2-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM64 Based SoC DT Updates for v4.16
* Add usb3_phy node to r8a7795 (R-Car H3) and r8a7796 (R-Car M3-W) SoCs, and
enable usb3_peri0 on salvator boards
* Allow DTBs of boards of r8a7795 (R-Car H3) and r8a7796 SoCs to build
without any warnings when compiled with W=1 using gcc-linaro-5.4.1-2017.05
- Move nodes which have no reg property out of bus, they don't belong there
- Add reg properties to dummy pciec[01] nodes
- Also sort sub-nodes of root node to allow for easier maintenance
* Add Add EthernetAVB PHY reset to r8a7795 (R-Car H3) and r8a7796 SoCs boards.
Geert Uytterhoeven says "... add properties to describe the EthernetAVB
PHY reset topology to the common Salvator-X/XS and ULCB DTS files, which
solves two issues:
1. On Salvator-XS, the enable pin of the regulator providing PHY power
is connected to PRESETn, and PSCI powers down the SoC during system
suspend. Hence a PHY reset is needed to restore network
functionality after system resume.
2. Linux should not rely on the boot loader having reset the PHY, but
should reset the PHY during driver probe."
* tag 'renesas-arm64-dt2-for-v4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: salvator-common: enable usb3_peri0
arm64: dts: renesas: salvator-common: enable usb3_phy0 node
arm64: dts: renesas: r8a7796: add usb3_phy node
arm64: dts: renesas: r8a7795: add usb3_phy node
arm64: dts: renesas: r8a7796: add reg properties to pciec[01] nodes
arm64: dts: renesas: r8a7796: move nodes which have no reg property out of bus
arm64: dts: renesas: r8a7796: sort subnodes of root node alphabetically
arm64: dts: renesas: r8a7795: sort subnodes of root node alphabetically
arm64: dts: renesas: ulcb: Add EthernetAVB PHY reset
arm64: dts: renesas: salvator-common: Add EthernetAVB PHY reset
arm64: dts: renesas: r8a7795: Move nodes which have no reg property out of bus
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add SD card support for the hi3798cv200-poplar board
- Replace the PMU node with exact match for the hi3660 SoC
- Add cpu capacity-dmips-mhz information for the hi3660 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=F5Y/
-----END PGP SIGNATURE-----
Merge tag 'hisi-arm64-dt-for-4.16-v2' of git://github.com/hisilicon/linux-hisi into next/dt
ARM64: DT: Hisilicon SoC DT updates for 4.16
- Add SD card support for the hi3798cv200-poplar board
- Replace the PMU node with exact match for the hi3660 SoC
- Add cpu capacity-dmips-mhz information for the hi3660 SoC
* tag 'hisi-arm64-dt-for-4.16-v2' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hisilicon: Add hi3660 cpu capacity-dmips-mhz information
arm64: dts: hi3660: improve pmu description
arm64: dts: hi3798cv200: add SD card support
Signed-off-by: Olof Johansson <olof@lixom.net>
The added header inclusion broke the 'allmodconfig' build in
arm-soc, presumably since the file is added in a different tree:
In file included from arch/arm64/boot/dts/sprd/sp9860g-1h10.dts:11:0:
arch/arm64/boot/dts/sprd/sc9860.dtsi:10:10: fatal error: dt-bindings/clock/sprd,sc9860-clk.h: No such file or directory
It turns out we don't actually need to include it at all, so
I'm removing the line again to fix the build.
Fixes: 22f37a2429 ("arm64: dts: add clocks for SC9860")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes this time include mostly device tree changes, as usual,
the notable ones include:
- A number of patches to fix most of the remaining DTC warnings
that got introduced when DTC started warning about some
obvious mistakes. We still have some remaining warnings that
probably may have to wait until 4.16 to get fixed while we
try to figure out what the correct contents should be.
- On Allwinner A64, Ethernet PHYs need a fix after a mistake in
coordination between patches merged through multiple branches.
- Various fixes for PMICs on allwinner based boards
- Two fixes for ethernet link detection on some Renesas machines
- Two stability fixes for rockchip based boards
Aside from device-tree, two other areas got fixes for older
problems:
- For TI Davinci DM365, a couple of fixes were needed to repair
the MMC DMA engine support, apparently this has been broken for
a while.
- One important fix for all Allwinner chips with the PMIC driver
as a loadable module.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mQiF
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Fixes this time include mostly device tree changes, as usual, the
notable ones include:
- A number of patches to fix most of the remaining DTC warnings that
got introduced when DTC started warning about some obvious
mistakes. We still have some remaining warnings that probably may
have to wait until 4.16 to get fixed while we try to figure out
what the correct contents should be.
- On Allwinner A64, Ethernet PHYs need a fix after a mistake in
coordination between patches merged through multiple branches.
- Various fixes for PMICs on allwinner based boards
- Two fixes for ethernet link detection on some Renesas machines
- Two stability fixes for rockchip based boards
Aside from device-tree, two other areas got fixes for older problems:
- For TI Davinci DM365, a couple of fixes were needed to repair the
MMC DMA engine support, apparently this has been broken for a
while.
- One important fix for all Allwinner chips with the PMIC driver as a
loadable module"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
arm64: dts: uniphier: fix gpio-ranges property of PXs3 SoC
arm64: dts: renesas: ulcb: Remove renesas, no-ether-link property
arm64: dts: renesas: salvator-x: Remove renesas, no-ether-link property
ARM: dts: tango4: remove bogus interrupt-controller property
ARM: dts: ls1021a: fix incorrect clock references
ARM: dts: aspeed-g4: Correct VUART IRQ number
ARM: dts: exynos: Enable Mixer node for Exynos5800 Peach Pi machine
ARM: dts: sun8i: a711: Reinstate the PMIC compatible
ARM: davinci: fix mmc entries in dm365's dma_slave_map
ARM: dts: da850-lego-ev3: Fix battery voltage gpio
ARM: davinci: Add dma_mask to dm365's eDMA device
ARM: davinci: Use platform_device_register_full() to create pdev for dm365's eDMA
arm64: dts: rockchip: limit rk3328-rock64 gmac speed to 100MBit for now
arm64: dts: rockchip: remove vdd_log from rk3399-puma
arm64: dts: orange-pi-zero-plus2: fix sdcard detect
arm64: allwinner: a64-sopine: Fix to use dcdc1 regulator instead of vcc3v3
ARM: dts: sunxi: Convert to CCU index macros for HDMI controller
sunxi-rsb: Include OF based modalias in device uevent
ARM: dts: at91: disable the nxp,se97b SMBUS timeout on the TSE-850
arm64: dts: rockchip: fix trailing 0 in rk3328 tsadc interrupts
...
Some clocks on SC9860 are in the same address area with syscon devices,
those are what have a property of 'sprd,syscon' which would refer to
syscon devices, others would have a reg property indicated their address
ranges.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some clocks on SC9860 are in the same address area with syscon
devices, the proper syscon node will be quoted under the
definitions of those clocks in DT.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is probably a copy-paste mistake. The gpio-ranges of PXs3 is
different from that of LD20.
Fixes: 277b51e705 ("arm64: dts: uniphier: add GPIO controller nodes")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
First, one fix that adds proper regulator references for the EMAC
external PHYs on A64 boards. The EMAC bindings were developed for 4.13,
but reverted at the last minute. They were finalized and brought back
for 4.15. However in the time between, regulator support for the A64
boards was merged. When EMAC device tree changes were reintroduced,
this was not taken into account.
Second, a patch that adds OF based modalias uevent for RSB slave devices.
This has been missing since the introduction of RSB, and recently with
PMIC regulator support introduced for the A64, has been seen affecting
distributions, which have the all-important PMIC mfd drivers built as
modules, which then don't get loaded.
Other minor cleanups include final conversion of raw indices to CCU
binding macros for sun[4567]i HDMI, cleanup of dummy regulators on the
A64 SOPINE, a SD card detection polarity fix for the Orange Pi Zero
Plus2, and adding a missing compatible for the PMIC on the TBS A711
tablet.
-----BEGIN PGP SIGNATURE-----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=FCgU
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Pull "Allwinner fixes for 4.15" from Chen-Yu Tsai:
First, one fix that adds proper regulator references for the EMAC
external PHYs on A64 boards. The EMAC bindings were developed for 4.13,
but reverted at the last minute. They were finalized and brought back
for 4.15. However in the time between, regulator support for the A64
boards was merged. When EMAC device tree changes were reintroduced,
this was not taken into account.
Second, a patch that adds OF based modalias uevent for RSB slave devices.
This has been missing since the introduction of RSB, and recently with
PMIC regulator support introduced for the A64, has been seen affecting
distributions, which have the all-important PMIC mfd drivers built as
modules, which then don't get loaded.
Other minor cleanups include final conversion of raw indices to CCU
binding macros for sun[4567]i HDMI, cleanup of dummy regulators on the
A64 SOPINE, a SD card detection polarity fix for the Orange Pi Zero
Plus2, and adding a missing compatible for the PMIC on the TBS A711
tablet.
* tag 'sunxi-fixes-for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a711: Reinstate the PMIC compatible
arm64: dts: orange-pi-zero-plus2: fix sdcard detect
arm64: allwinner: a64-sopine: Fix to use dcdc1 regulator instead of vcc3v3
ARM: dts: sunxi: Convert to CCU index macros for HDMI controller
sunxi-rsb: Include OF based modalias in device uevent
arm64: allwinner: a64: add Ethernet PHY regulator for several boards
Vladimir Zapolskiy says:
The present change is a bug fix for AVB link iteratively up/down.
Steps to reproduce:
- start AVB TX stream (Using aplay via MSE),
- disconnect+reconnect the eth cable,
- after a reconnection the eth connection goes iteratively up/down
without user interaction,
- this may heal after some seconds or even stay for minutes.
As the documentation specifies, the "renesas,no-ether-link" option
should be used when a board does not provide a proper AVB_LINK signal.
There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
and ULCB starter kits since the AVB_LINK is correctly handled by HW.
Choosing to keep or remove the "renesas,no-ether-link" option will
have impact on the code flow in the following ways:
- keeping this option enabled may lead to unexpected behavior since
the RX & TX are enabled/disabled directly from adjust_link function
without any HW interrogation,
- removing this option, the RX & TX will only be enabled/disabled after
HW interrogation. The HW check is made through the LMON pin in PSR
register which specifies AVB_LINK signal value (0 - at low level;
1 - at high level).
In conclusion, the change is also a safety improvement because it
removes the "renesas,no-ether-link" option leading to a proper way
of detecting the link state based on HW interrogation and not on
software heuristic.
Note that DTS files for V3M Starter Kit, Draak and Eagle boards
contain the same property, the files are untouched due to unavailable
schematics to verify if the fix applies to these boards as well.
-----BEGIN PGP SIGNATURE-----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=kmQd
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Pull "Renesas ARM Based SoC Fixes for v4.15" from Simon Horman:
Vladimir Zapolskiy says:
The present change is a bug fix for AVB link iteratively up/down.
Steps to reproduce:
- start AVB TX stream (Using aplay via MSE),
- disconnect+reconnect the eth cable,
- after a reconnection the eth connection goes iteratively up/down
without user interaction,
- this may heal after some seconds or even stay for minutes.
As the documentation specifies, the "renesas,no-ether-link" option
should be used when a board does not provide a proper AVB_LINK signal.
There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
and ULCB starter kits since the AVB_LINK is correctly handled by HW.
Choosing to keep or remove the "renesas,no-ether-link" option will
have impact on the code flow in the following ways:
- keeping this option enabled may lead to unexpected behavior since
the RX & TX are enabled/disabled directly from adjust_link function
without any HW interrogation,
- removing this option, the RX & TX will only be enabled/disabled after
HW interrogation. The HW check is made through the LMON pin in PSR
register which specifies AVB_LINK signal value (0 - at low level;
1 - at high level).
In conclusion, the change is also a safety improvement because it
removes the "renesas,no-ether-link" option leading to a proper way
of detecting the link state based on HW interrogation and not on
software heuristic.
Note that DTS files for V3M Starter Kit, Draak and Eagle boards
contain the same property, the files are untouched due to unavailable
schematics to verify if the fix applies to these boards as well.
* tag 'renesas-fixes-for-v4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: ulcb: Remove renesas, no-ether-link property
arm64: dts: renesas: salvator-x: Remove renesas, no-ether-link property
Fix typo in unit address of MSCL clock controller (the reg entry is
correct) of Exynso5433.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Convert all hex addresses in node unit addresses to lower case to
fix warnings like:
arch/arm64/boot/dts/exynos/exynos5433-tm2e.dtb: Warning (simple_bus_reg):
Node /soc/video-scaler@13C00000 simple-bus unit address format error, expected "13c00000"
Conversion was done using sed:
$ sed -e 's/@\([a-zA-Z0-9_-]*\) {/@\L\1 {/' -i arch/arm64/boot/dts/exynos/*.dts*
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Now that every architecture is using the generic clkdev.h file
and we no longer include asm/clkdev.h anywhere in the tree, we
can remove it.
Cc: Russell King <linux@armlinux.org.uk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The UEFI memory map is a bit vague about how to interpret the
EFI_MEMORY_XP attribute when it is combined with EFI_MEMORY_RP and/or
EFI_MEMORY_WP, which have retroactively been redefined as cacheability
attributes rather than permission attributes.
So let's ignore EFI_MEMORY_XP if _RP and/or _WP are also set. In this
case, it is likely that they are being used to describe the capability
of the region (i.e., whether it has the controls to reconfigure it as
non-executable) rather than the nature of the contents of the region
(i.e., whether it contains data that we will never attempt to execute)
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tyler Baicar <tbaicar@codeaurora.org>
Cc: Vasyl Gomonovych <gomonovych@gmail.com>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20180102181042.19074-3-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add support for the Cluster PMU part of the ARM DynamIQ Shared Unit (DSU).
The DSU integrates one or more cores with an L3 memory system, control
logic, and external interfaces to form a multicore cluster. The PMU
allows counting the various events related to L3, SCU etc, along with
providing a cycle counter.
The PMU can be accessed via system registers, which are common
to the cores in the same cluster. The PMU registers follow the
semantics of the ARMv8 PMU, mostly, with the exception that
the counters record the cluster wide events.
This driver is mostly based on the ARMv8 and CCI PMU drivers.
The driver only supports ARM64 at the moment. It can be extended
to support ARM32 by providing register accessors like we do in
arch/arm64/include/arm_dsu_pmu.h.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Make use of the new generic helper to convert an of_node of a CPU
to the logical CPU id in parsing the topology.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This is entirely cosmetic, but somehow it was missed when sending
differing versions of this patch. This just makes the file a bit more
uniform.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
CPU_PM_CPU_IDLE_ENTER_RETENTION skips calling cpu_pm_enter() and
cpu_pm_exit(). By not calling cpu_pm functions in idle entry/exit
paths we can reduce the latency involved in entering and exiting
the low power idle state.
On ARM64 based Qualcomm server platform we measured below overhead
for calling cpu_pm_enter and cpu_pm_exit for retention states.
workload: stress --hdd #CPUs --hdd-bytes 32M -t 30
Average overhead of cpu_pm_enter - 1.2us
Average overhead of cpu_pm_exit - 3.1us
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We currently check if the VM has a userspace irqchip in several places
along the critical path, and if so, we do some work which is only
required for having an irqchip in userspace. This is unfortunate, as we
could avoid doing any work entirely, if we didn't have to support
irqchip in userspace.
Realizing the userspace irqchip on ARM is mostly a developer or hobby
feature, and is unlikely to be used in servers or other scenarios where
performance is a priority, we can use a refcounted static key to only
check the irqchip configuration when we have at least one VM that uses
an irqchip in userspace.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Since commit 93390c0a1b ("arm64: KVM: Hide unsupported AArch64 CPU
features from guests") we can hide cpu features from guests. Apply
this to a long standing issue where guests see a PMU available, but
it's not, because it was not enabled by KVM's userspace.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
This node was the only one that didn't have the same set of pins in
active and suspend mode.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Nodes relative to the first sdhc node were interlaced with node of the
second sdhc. Move sdhc2_cd_pin with its siblings to prevent that. Also
rename the grouping node from sdhc2_cd_pin to pmx_sdc2_cd_pin, as
"pmx_sdc" is the prefix used by other nodes.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The QUP core can be used either for I2C or SPI, so the same IP is mapped
by a driver or the other. SPI bindings use a leading 0 for the start
address and a size of 0x600, I2C bindings don't have the leading 0 and
have a size 0x1000.
To make them more similar, add the leading 0 to I2C bindings and changes
the size to 0x500 for all of them, as this is the actual size of these
blocks. Also align the second entry of the clocks array.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
These nodes reserve and configure some pins as GPIOs. They are not
generic pinctrls, they actually belong to board files but they are not
used by any other node, so just drop them altogether.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Drop assignments to bias-disable as the documentation [1] states that
this property doesn't take a value. Other occurrences of this property
respect that.
[1] Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.txt
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Indentation did not respect kernel standards, so fix that for the usual
indent with tabs, align with spaces. While at it, remove some empty
lines before and after the closing parenthesis of this block.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
SMSM is not symmetrical, the incoming bits from WCNSS are available at
index 6, but the outgoing host id for WCNSS is 3. Further more, upstream
references the base of APCS (in contrast to downstream), so the register
offset of 8 must be included.
Fixes: 1fb47e0a9b ("arm64: dts: qcom: msm8916: Add smsm and smp2p nodes")
Cc: stable@vger.kernel.org
Reported-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The serial pins of PXs3 SoC are not multiplexed with any other
functions. Enable serial2 and serial3 on the PXs3 reference board
because I see the connectors on the board.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The DE2 CCU on Allwinner H5 SoC has a slightly different behavior than
the one on H3, so the compatible string is not set in the common DTSI
file.
Add the compatible string of H5 DE2 CCU in H5 DTSI file.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2017-12-28
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Fix incorrect state pruning related to recognition of zero initialized
stack slots, where stacksafe exploration would mistakenly return a
positive pruning verdict too early ignoring other slots, from Gianluca.
2) Various BPF to BPF calls related follow-up fixes. Fix an off-by-one
in maximum call depth check, and rework maximum stack depth tracking
logic to fix a bypass of the total stack size check reported by Jann.
Also fix a bug in arm64 JIT where prog->jited_len was uninitialized.
Addition of various test cases to BPF selftests, from Alexei.
3) Addition of a BPF selftest to test_verifier that is related to BPF to
BPF calls which demonstrates a late caller stack size increase and
thus out of bounds access. Fixed above in 2). Test case from Jann.
4) Addition of correlating BPF helper calls, BPF to BPF calls as well
as BPF maps to bpftool xlated dump in order to allow for better
BPF program introspection and debugging, from Daniel.
5) Fixing several bugs in BPF to BPF calls kallsyms handling in order
to get it actually to work for subprogs, from Daniel.
6) Extending sparc64 JIT support for BPF to BPF calls and fix a couple
of build errors for libbpf on sparc64, from David.
7) Allow narrower context access for BPF dev cgroup typed programs in
order to adapt to LLVM code generation. Also adjust memlock rlimit
in the test_dev_cgroup BPF selftest, from Yonghong.
8) Add netdevsim Kconfig entry to BPF selftests since test_offload.py
relies on netdevsim device being available, from Jakub.
9) Reduce scope of xdp_do_generic_redirect_map() to being static,
from Xiongwei.
10) Minor cleanups and spelling fixes in BPF verifier, from Colin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a full/low speed device is connected to USB 2.0 port on UniPhier SoC
that has ehci controller, the kernel shows the following messages.
| usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
| usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
| usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
| usb usb1-port1: unable to enumerate USB device
To fix the issue, the driver needs to enable Transaction Translator on ehci
root hub. This adds 'has-transaction-translator' property to each node.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Ina220 chip was used on ls208xardb platform to monitor power
comsumption. So add ina220 chip node in dts to enable power
consumption monitor feature.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add USB support on ls1088ardb
Signed-off-by: yinbo zhu <yinbo.zhu@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* for-next/52-bit-pa:
arm64: enable 52-bit physical address support
arm64: allow ID map to be extended to 52 bits
arm64: handle 52-bit physical addresses in page table entries
arm64: don't open code page table entry creation
arm64: head.S: handle 52-bit PAs in PTEs in early page table setup
arm64: handle 52-bit addresses in TTBR
arm64: limit PA size to supported range
arm64: add kconfig symbol to configure physical address size
Now that 52-bit physical address support is in place, add the kconfig
symbol to enable it. As described in ARMv8.2, the larger addresses are
only supported with the 64k granule. Also ensure that PAN is configured
(or TTBR0 PAN is not), as explained in an earlier patch in this series.
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Bob Picco <bob.picco@oracle.com>
Reviewed-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Currently, when using VA_BITS < 48, if the ID map text happens to be
placed in physical memory above VA_BITS, we increase the VA size (up to
48) and create a new table level, in order to map in the ID map text.
This is okay because the system always supports 48 bits of VA.
This patch extends the code such that if the system supports 52 bits of
VA, and the ID map text is placed that high up, then we increase the VA
size accordingly, up to 52.
One difference from the current implementation is that so far the
condition of VA_BITS < 48 has meant that the top level table is always
"full", with the maximum number of entries, and an extra table level is
always needed. Now, when VA_BITS = 48 (and using 64k pages), the top
level table is not full, and we simply need to increase the number of
entries in it, instead of creating a new table level.
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Bob Picco <bob.picco@oracle.com>
Reviewed-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[catalin.marinas@arm.com: reduce arguments to __create_hyp_mappings()]
[catalin.marinas@arm.com: reworked/renamed __cpu_uses_extended_idmap_level()]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The top 4 bits of a 52-bit physical address are positioned at bits
12..15 of a page table entry. Introduce macros to convert between a
physical address and its placement in a table entry, and change all
macros/functions that access PTEs to use them.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Bob Picco <bob.picco@oracle.com>
Reviewed-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[catalin.marinas@arm.com: some long lines wrapped]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Instead of open coding the generation of page table entries, use the
macros/functions that exist for this - pfn_p*d and p*d_populate. Most
code in the kernel already uses these macros, this patch tries to fix
up the few places that don't. This is useful for the next patch in this
series, which needs to change the page table entry logic, and it's
better to have that logic in one place.
The KVM extended ID map is special, since we're creating a level above
CONFIG_PGTABLE_LEVELS and the required function isn't available. Leave
it as is and add a comment to explain it. (The normal kernel ID map code
doesn't need this change because its page tables are created in assembly
(__create_page_tables)).
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Bob Picco <bob.picco@oracle.com>
Reviewed-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The top 4 bits of a 52-bit physical address are positioned at bits
12..15 in page table entries. Introduce a macro to move the bits there,
and change the early ID map and swapper table setup code to use it.
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Bob Picco <bob.picco@oracle.com>
Reviewed-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[catalin.marinas@arm.com: additional comments for clarification]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The top 4 bits of a 52-bit physical address are positioned at bits 2..5
in the TTBR registers. Introduce a couple of macros to move the bits
there, and change all TTBR writers to use them.
Leave TTBR0 PAN code unchanged, to avoid complicating it. A system with
52-bit PA will have PAN anyway (because it's ARMv8.1 or later), and a
system without 52-bit PA can only use up to 48-bit PAs. A later patch in
this series will add a kconfig dependency to ensure PAN is configured.
In addition, when using 52-bit PA there is a special alignment
requirement on the top-level table. We don't currently have any VA_BITS
configuration that would violate the requirement, but one could be added
in the future, so add a compile-time BUG_ON to check for it.
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Bob Picco <bob.picco@oracle.com>
Reviewed-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[catalin.marinas@arm.com: added TTBR_BADD_MASK_52 comment]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We currently copy the physical address size from
ID_AA64MMFR0_EL1.PARange directly into TCR.(I)PS. This will not work for
4k and 16k granule kernels on systems that support 52-bit physical
addresses, since 52-bit addresses are only permitted with the 64k
granule.
To fix this, fall back to 48 bits when configuring the PA size when the
kernel does not support 52-bit PAs. When it does, fall back to 52, to
avoid similar problems in the future if the PA size is ever increased
above 52.
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Bob Picco <bob.picco@oracle.com>
Reviewed-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[catalin.marinas@arm.com: tcr_set_pa_size macro renamed to tcr_compute_pa_size]
[catalin.marinas@arm.com: comments added to tcr_compute_pa_size]
[catalin.marinas@arm.com: definitions added for TCR_*PS_SHIFT]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
ARMv8.2 introduces support for 52-bit physical addresses. To prepare for
supporting this, add a new kconfig symbol to configure the physical
address space size. The symbols will be used in subsequent patches.
Currently the only choice is 48, a later patch will add the option of 52
once the required code is in place.
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Bob Picco <bob.picco@oracle.com>
Reviewed-by: Bob Picco <bob.picco@oracle.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
[catalin.marinas@arm.com: folded minor patches into this one]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Lots of overlapping changes. Also on the net-next side
the XDP state management is handled more in the generic
layers so undo the 'net' nfp fix which isn't applicable
in net-next.
Include a necessary change by Jakub Kicinski, with log message:
====================
cls_bpf no longer takes care of offload tracking. Make sure
netdevsim performs necessary checks. This fixes a warning
caused by TC trying to remove a filter it has not added.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The following dt entries are added:
cpus [0-3] (Cortex A53):
- capacity-dmips-mhz = <592>;
cpus [4-7] (Cortex A73):
- capacity-dmips-mhz = <1024>;
Those values were obtained by running dhrystone 2.1 on a
HiKey960 with the following procedure:
- Offline all CPUs but CPU0 (A53)
- Set CPU0 frequency to maximum
- Run Dhrystone 2.1 for 20 seconds
- Offline all CPUs but CPU4 (A73)
- set CPU4 frequency to maximum
- Run Dhrystone 2.1 for 20 seconds
The results are as follows:
A53: 129633887 loops
A73: 287034147 loops
By scaling those values so that the A73s use 1024, we end up with 462
for the A53s. However, they have different maximum frequencies:
1.844GHz for A53s and 2.362GHz for A73s. Thus, we can scale the A53
value to truly represent dmips per MHz, and we end up with 592.
The impact of this change can be verified on HiKey960:
$ cat /sys/devices/system/cpu/cpu*/cpufreq/scaling_cur_freq
1844000
1844000
1844000
1844000
2362000
2362000
2362000
2362000
$ cat /sys/devices/system/cpu/cpu*/cpu_capacity
462
462
462
462
1024
1024
1024
1024
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
cortex-a73 pmu driver is supported now. hi3660 is 4*a73 + 4*a53, so it
should use "cortex-a73-pmu" and "cortex-a53-pmu" instead of "armpmu-v3",
then we can use the a73 and a53 events in perf tool directly.
Signed-off-by: Xu YiPing <xuyiping@hisilicon.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The present change is a bug fix for AVB link iteratively up/down.
Steps to reproduce:
- start AVB TX stream (Using aplay via MSE),
- disconnect+reconnect the eth cable,
- after a reconnection the eth connection goes iteratively up/down
without user interaction,
- this may heal after some seconds or even stay for minutes.
As the documentation specifies, the "renesas,no-ether-link" option
should be used when a board does not provide a proper AVB_LINK signal.
There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
and ULCB starter kits since the AVB_LINK is correctly handled by HW.
Choosing to keep or remove the "renesas,no-ether-link" option will
have impact on the code flow in the following ways:
- keeping this option enabled may lead to unexpected behavior since
the RX & TX are enabled/disabled directly from adjust_link function
without any HW interrogation,
- removing this option, the RX & TX will only be enabled/disabled after
HW interrogation. The HW check is made through the LMON pin in PSR
register which specifies AVB_LINK signal value (0 - at low level;
1 - at high level).
In conclusion, the present change is also a safety improvement because
it removes the "renesas,no-ether-link" option leading to a proper way
of detecting the link state based on HW interrogation and not on
software heuristic.
Fixes: dc36965a89 ("arm64: dts: r8a7796: salvator-x: Enable EthernetAVB")
Fixes: 6fa501c549 ("arm64: dts: r8a7795: enable EthernetAVB on Salvator-X")
Signed-off-by: Bogdan Mirea <Bogdan-Stefan_Mirea@mentor.com>
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The present change is a bug fix for AVB link iteratively up/down.
Steps to reproduce:
- start AVB TX stream (Using aplay via MSE),
- disconnect+reconnect the eth cable,
- after a reconnection the eth connection goes iteratively up/down
without user interaction,
- this may heal after some seconds or even stay for minutes.
As the documentation specifies, the "renesas,no-ether-link" option
should be used when a board does not provide a proper AVB_LINK signal.
There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
and ULCB starter kits since the AVB_LINK is correctly handled by HW.
Choosing to keep or remove the "renesas,no-ether-link" option will
have impact on the code flow in the following ways:
- keeping this option enabled may lead to unexpected behavior since
the RX & TX are enabled/disabled directly from adjust_link function
without any HW interrogation,
- removing this option, the RX & TX will only be enabled/disabled after
HW interrogation. The HW check is made through the LMON pin in PSR
register which specifies AVB_LINK signal value (0 - at low level;
1 - at high level).
In conclusion, the present change is also a safety improvement because
it removes the "renesas,no-ether-link" option leading to a proper way
of detecting the link state based on HW interrogation and not on
software heuristic.
Fixes: dc36965a89 ("arm64: dts: r8a7796: salvator-x: Enable EthernetAVB")
Fixes: 6fa501c549 ("arm64: dts: r8a7795: enable EthernetAVB on Salvator-X")
Signed-off-by: Bogdan Mirea <Bogdan-Stefan_Mirea@mentor.com>
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
for the type-c phys. The Kevin Chromebooks based on rk3399 now can use their
internal edp displays. RK3328 gets its efuse node and Mali450 gpu node,
which actually produces already some nice results with the WIP Lima driver.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlo7/J4QHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgVogB/wNdimvRAq7DdpIXxzMxoIEB3jXZ1zJ2TVL
Gxim5h0RizQGIoiV4CYkQG2CdB1HG4Updj4SW9GYMl004fklSA26fB64WFVDM0VR
8uqVxkyCgo2QzzQxsNDPrXvNv3WjbrFVe+pWebzUZ1RCkHBgeJA/o61vjdNdvwq3
jgnr0YDjYYU+9sqoq31SYe0vzvoDGPmE7+Mlmw3eAszQqV66sk0/50IKV5z4xx8e
oyD4M0JpPhGyPMoaBIekzr4wjkrKbEeJ5VQy/afFAYJWzi8X+vABIH78kGl+9q76
AmEQxBWr0ZQSIPWTVofUzHzKX78gSt2Gts2kbaFXPzMbCn8xWcKM
=C4Hu
-----END PGP SIGNATURE-----
Merge tag 'v4.16-rockchip-dts64-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "Rockchip dts64 changes for 4.16" from Heiko Stübner:
General RK3399 gets Mipi nodes, fixes for usb3 support and better support
for the type-c phys. The Kevin Chromebooks based on rk3399 now can use their
internal edp displays. RK3328 gets its efuse node and Mali450 gpu node,
which actually produces already some nice results with the WIP Lima driver.
* tag 'v4.16-rockchip-dts64-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Add efuse device node for RK3328 SoC
arm64: dts: rockchip: add rk3328 mali gpu node
dt-bindings: gpu: mali-utgard: add rockchip,rk3328-mali compatible
arm64: dts: rockchip: add extcon nodes and enable tcphy rk3399-gru
arm64: dts: rockchip: add usb3-phy otg-port support for rk3399
arm64: dts: rockchip: add reset property for dwc3 controllers on rk3399
arm64: dts: rockchip: add the aclk_usb3 clocks for USB3 on rk3399
arm64: dts: rockchip: add pd_usb3 power-domain node for rk3399
arm64: dts: rockchip: Enable edp disaplay on kevin
arm64: dts: rockchip: update mipi cells for RK3399
arm64: dts: rockchip: add mipi_dsi1 support for rk3399
arm64: dts: rockchip: add rk3399 DSI0 reset
No Qualcomm SoC requires the "phy-qcom-8x16-usb.c" USB phy driver
support any more. Remove the code, and remove the config option
from the arm64 defconfig.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
No Qualcomm SoC requires the "phy-msm-usb.c" USB phy driver support
any more. Remove the code, and remove the config option from the
arm64 defconfig.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
No Qualcomm SoC requires the "ehci-msm.c" code any more. So remove
the code, and remove the config option from the arm64 defconfig.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
- A bug in handling of SPE state for non-vhe systems
- A fix for a crash on system shutdown
- Three timer fixes, introduced by the timer optimizations for v4.15
x86 fixes:
- fix for a WARN that was introduced in 4.15
- fix for SMM when guest uses PCID
- fixes for several bugs found by syzkaller
... and a dozen papercut fixes for the kvm_stat tool.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJaO6N9AAoJEL/70l94x66DC1wH/Rf+u0Cj6ZQil6LK6Nf8bfPd
3TqrwrxUDeXwi8GzsvK14izBr1mDzidSHIO0Q4XINFRSRdaf43h3R2im/SJqvNhP
xktCmJI2CxN96oaC7kIExgwf3YKhFdLIADfbT8oR9p3xZG/+c97dkr3b4XtmVCDb
ZXdUEOcKnoW4zwpfJN30FLlq4OwYvuYVz02AEfPivZRDfhhus/TYSnuSdxH8CLNf
75ymuKyXoo/RELbimwbMk8Cm9+ey7PjlUGOgbnbXIFtmgznXhLzAOeES2B+46J5b
sMBPlmiJrn6N//lM18CC5yOBzBLGsYOoXggtw4aU/5nM4GVcFebWedpcoD4D8Jw=
=Bt8w
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"ARM fixes:
- A bug in handling of SPE state for non-vhe systems
- A fix for a crash on system shutdown
- Three timer fixes, introduced by the timer optimizations for v4.15
x86 fixes:
- fix for a WARN that was introduced in 4.15
- fix for SMM when guest uses PCID
- fixes for several bugs found by syzkaller
... and a dozen papercut fixes for the kvm_stat tool"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (22 commits)
tools/kvm_stat: sort '-f help' output
kvm: x86: fix RSM when PCID is non-zero
KVM: Fix stack-out-of-bounds read in write_mmio
KVM: arm/arm64: Fix timer enable flow
KVM: arm/arm64: Properly handle arch-timer IRQs after vtimer_save_state
KVM: arm/arm64: timer: Don't set irq as forwarded if no usable GIC
KVM: arm/arm64: Fix HYP unmapping going off limits
arm64: kvm: Prevent restoring stale PMSCR_EL1 for vcpu
KVM/x86: Check input paging mode when cs.l is set
tools/kvm_stat: add line for totals
tools/kvm_stat: stop ignoring unhandled arguments
tools/kvm_stat: suppress usage information on command line errors
tools/kvm_stat: handle invalid regular expressions
tools/kvm_stat: add hint on '-f help' to man page
tools/kvm_stat: fix child trace events accounting
tools/kvm_stat: fix extra handling of 'help' with fields filter
tools/kvm_stat: fix missing field update after filter change
tools/kvm_stat: fix drilldown in events-by-guests mode
tools/kvm_stat: fix command line option '-g'
kvm: x86: fix WARN due to uninitialized guest FPU state
...
This set of patches enables a bunch of new features on Jetson TX2 that
were finally unblocked by the GPIO driver getting merged for v4.15.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAlo6tuMTHHRyZWRpbmdA
bnZpZGlhLmNvbQAKCRDdI6zXfz6zodskD/wLlXn2w48dUcTJDqwQr5I4FsLKe99u
si2Ci4MW3M/62apNGpc7HaKE5H7XWYuzeL282IJEKwPpnzg3YGb+9cvgi9fyjgOz
G+Faze57wMWzfFvEQBoNXtOjA/6W9jeurxm/41naTVl9XtKYxIXUECwKxdZboT2t
9lfJIuAJIWKh8MCpWf9LzNJPW9lld5rbxk/M7htczsCPdmPNdSZwJQMh9lJmw2Mc
fBOp4NbY4gU3Tcaua9NWaEMUC5Zf07FgEaQldH1gsRAOlA5ZlraHBjjUcQq/kOTf
ApRcnIUpR4BdC5GPKn49ahrPrPwfKNdfLaeynd1WL9+ELnFSzBYotLVmWIGExxDc
F3cIzkEmAX5xzjLs/eCeX3rlW1jvBcx0+nxZ2TkuBnKegG4tL0cma2W1k6pcU4xj
s3WDmdGcr5U1a1/a/CCSn7nV7SKgJVr5knuwxiZKqtQlzyjJI5VidfhT4yJ0pnsk
t2Eird2eWH9O8CjvpEya4gc6QKUdj6/VoykutJUfw0aApIIY2ZGWYQ6l9tf9pE6O
RYEOhX9oS2XL5NUGiu5CE3XdjIaMcZ53qkqH0U1wd1yfc3siWKilZ/2OPEaDG3tH
YNQZkoLQ6P5rOz+YNhSI9VCYXIkJ/A/XbSg+NAvnxfLxVcPZ0XcIZYS8SNbORMUf
EsrMYd4QiIjtyA==
=7QxU
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.16-arm64-dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Pull "arm64: tegra: Changes for v4.16-rc1" from Thierry Reding:
This set of patches enables a bunch of new features on Jetson TX2 that
were finally unblocked by the GPIO driver getting merged for v4.15.
* tag 'tegra-for-4.16-arm64-dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Use sor1_out clock
arm64: tegra: Fix SD write-protect polarity on Jetson TX2
arm64: tegra: Add CPU and PSCI nodes for NVIDIA Tegra210 platforms
arm64: tegra: Enable HDMI on Jetson TX2
arm64: tegra: Mark I2C4 as DDC on P3310
arm64: tegra: Add display nodes on Tegra186
arm64: tegra: Add SMMU node for Tegra186
arm64: tegra: Enable memory controller on P3310
arm64: tegra: Add memory controller on Tegra186
arm64: tegra: Add FUSE block on Tegra186
arm64: tegra: Add MISC registers on Tegra186
1. Add CPU perf counters to Exynos5433.
2. Add missing power domains to Exynos5433.
3. Add NFC chip to Exynos5433 TM2/TM2E.
4. Fix obscure bugs on I2C transfers to MHL chip on TM2/TM2E.
-----BEGIN PGP SIGNATURE-----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=dsdB
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Samsung DTS ARM64 changes for v4.16" from Krzysztof Kozłowski:
1. Add CPU perf counters to Exynos5433.
2. Add missing power domains to Exynos5433.
3. Add NFC chip to Exynos5433 TM2/TM2E.
4. Fix obscure bugs on I2C transfers to MHL chip on TM2/TM2E.
* tag 'samsung-dt64-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Increase bus frequency for MHL chip
arm64: dts: exynos: Add remaining power domains to Exynos5433 SoC
arm64: dts: exynos: Add AUD power domain to Exynos5433 SoC
arm64: dts: exynos: Add MFC power domain to Exynos 5433 SoC
arm64: dts: exynos: Add MSCL power domain to Exynos 5433 SoC
arm64: dts: exynos: Add DISP power domain to Exynos 5433 SoC
arm64: dts: exynos: Add GSCL power domain to Exynos 5433 SoC
arm64: dts: exynos: Add support for S3FWRN5 NFC chip to TM2(e) boards
arm64: dts: exynos: Add CPU performance counters to Exynos5433 boards
Removed as well got the vdd_log regulator from the rk3399-puma board.
While it is there, the absence of any user makes it prone to configuration
problems when the pwm-regulator takes over the boot-up default and wiggles
settings there. Case in question was the PCIe host not working anymore.
With vdd_log removed for the time being, PCIe on Puma works again.
And a second stopgap is limiting the speed of the gmac on the rk3328-rock64
to 100MBit. While the hardware can reach 1GBit, currently it is not stable.
Limiting it to 100MBit for the time being allows nfsroots to be used again
until the problem is identified.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlosSekQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgcERB/9hWGZwQAexlfJj4mnAl61axE+KROHSsDFd
qrQqTX9LLbNr+Ot769w5okRWo1C3ItSWAGvy08Wksrx2Yq5y0RvbGeCA4CjpKxDA
jO1Aphe43rFXk3oMbRAnrr8zVMHjQZO0OCvyEfbQYZSr/uXV+wzNj9/Ll54xNFJd
6hwF+X/XGsQHOh7k6BrzWeXmpnIZ3s72EN7uIHg58HCa97Xnwwa25HR0UEIhR43F
BmP/1AID/JfALu0+F/VF2vnYeC8JL46/fX+xmi6YzsnRLOiCKIZMjuFBAQk7rE4/
qjSd7Xqi3F3c61wvnHw4s6QkHOFi48pJJfykEorV5yi7Yk9Kad4G
=I63w
-----END PGP SIGNATURE-----
Merge tag 'v4.15-rockchip-dts64fixes-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Pull "Rockchip dts64 fixes for 4.15" from Heiko Stübner:
Another trailing interrupt-cell 0 removed.
Removed as well got the vdd_log regulator from the rk3399-puma board.
While it is there, the absence of any user makes it prone to configuration
problems when the pwm-regulator takes over the boot-up default and wiggles
settings there. Case in question was the PCIe host not working anymore.
With vdd_log removed for the time being, PCIe on Puma works again.
And a second stopgap is limiting the speed of the gmac on the rk3328-rock64
to 100MBit. While the hardware can reach 1GBit, currently it is not stable.
Limiting it to 100MBit for the time being allows nfsroots to be used again
until the problem is identified.
* tag 'v4.15-rockchip-dts64fixes-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: limit rk3328-rock64 gmac speed to 100MBit for now
arm64: dts: rockchip: remove vdd_log from rk3399-puma
arm64: dts: rockchip: fix trailing 0 in rk3328 tsadc interrupts
- meson-gx: add VPU power domain support
- odroid-c2: add HDMI and CEC nodes
- misc cleanups
-----BEGIN PGP SIGNATURE-----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=0wR5
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt64' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Pull "Amlogic 64-bit DT updates for v4.16" from Kevin Hilman
- meson-gx: add VPU power domain support
- odroid-c2: add HDMI and CEC nodes
- misc cleanups
* tag 'amlogic-dt64' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gxm: fix q200 interrupt number
ARM64: dts: meson-gxm: add the PHY interrupt line on Khadas VIM2
ARM64: dts: meson: add comments with the GPIO for the PHY interrupts
ARM64: dts: amlogic: use generic bus node names
ARM64: dts: meson: drop "sana" clock from SAR ADC
ARM64: dts: odroid-c2: Add HDMI and CEC Nodes
ARM64: dts: meson-gx: grow reset controller memory zone
ARM64: dts: meson-gx: Add HDMI_5V regulator on selected boards
ARM64: dts: meson-gx: add VPU power domain
* Use r8a77970 (V3M) CPG core clock and SYSC power domain macros
These may be used in place of numeric constants now that they
are present in Linus's tree.
* Add r8a77970 (V3M) Starter Kit board support
This includes basic support to bring up the board with a serial
console and EtherAVB support
* Add IPMMU nodes and connections to on-chip devices
on r8a7795 (H3), r8a7796 (M3-W), r8a77970 (V3M) and r8a77995 (D3) SoCs
Simon Horman says "With these patches applied a white list enabled IPMMU
driver may be used to check silicon revision and then enable IPMMU in the
known working cases."
* Enable DMA for SCIF2 on r8a77995 (D2) SoC
* Increase the number of GPIO bank 1 ports to 29 on r8a7795 (H3) SoC
This adds support for the GP-1-28 port pin of the r8a7795 (H3) ES2.0 SoC
* Add support for CAN to r8a77995 (D3) SoC
Ulrich Hecht says "This is a by-the-datasheet implementation, with the
datasheet missing some bits, namely the pin map. I filled in the gaps...
by deducing the information from pin numbers already in the PFC driver,
so careful scrutiny is advised."
* Add support for SDHI to r8a77995 (D3) SoC
* Add SoC name to file header of r8a7795 (H3) and r8a7796 (M3-W)
Salvator-X and Salvator-XS board files
Geert Uytterhoeven says "With the proliferation of Salvator-X and
Salvator-XS boards carrying different R-Car Gen3 SoCs variants, several
DTS files ended up having the same file headers.
Add the SoC names to the file headers to avoid confusion."
* Add device note for ROHM BD9571MWV PMIC to
r8a7795 (H3) and r8a7796 (M3-W) Salvator-X and Salvator-XS boards.
Geert Uytterhoeven says "This was based on the example in the DT binding
documentation, but using IRQ0 instead of a GPIO interrupt, as that
matches the schematics, and because INTC-EX is a simpler block."
* Enable USB2.0 channel 0 on r8a77970 (V3M) ULCB Kingfisher board
Vladimir Barinov says "The dedicated USB0_PWEN pin is used to control
CN13 VBUS source from U43 power supply. MAX3355 can also provide VBUS,
hence it should be disabled via OTG_OFFVBUSn node coming from gpio
expander TCA9539. Set MAX3355 enabled using OTG_EXTLPn node to be able
to read OTG ID of CN13."
* Add support for r8a7795 (M3-W) Salvator-XS board
Geert Uytterhoeven says "This patch series adds support for the version
of the Salvator-XS development board equipped with an R-Car M3-W SiP.
The DT was based on work for the Salvator-X and -XS boards with M3-W
resp. H3 SiPs."
* Add watchdog timer support to r8a77970 (V3M) eagle board
Geert Uytterhoven says "This allows to use the watchdog timer to reset
the board, until PSCI is enhanced to include such functionality."
* Use Use R-Car SDHI Gen3 fallback on r8a7795 (H3) and r8a7796 (M3-W) SoCs
* Set driver type for MMC on r8a7795 (H3) and r8a7796 (M3-W) Salvator-X and
Salvator-XS boards.
Wolfram Sang says "These boards are known to have eMMC issues with the
default driver type. Specify a working one."
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE4nzZofWswv9L/nKF189kaWo3T74FAlopDo0ACgkQ189kaWo3
T74XOA/+Ptv9Odl/V2U9RZ87AGnwXnAjDWeO6QOOMfeTzy4Q0q7fz6r5FVicK1Am
H+Elb78vF2c+VuLOPmPxtB/dPOPgfb+NIvAxh4mEqhlEoCMs0nW2RsyTY9ydxzlw
JQM/alhlhh+rNniMUkz+hvfoZUCzaFpGKrUL8XXDxIMf3d7EBVeT9+EhfI+7FkHI
HDDCagM9vJGTwvVR6JMSvV8bcMgH+Pr4NL/OL9bA5iVlUmahsxRPiJP2Gi2cSsA6
h+vbLna4LWTiKmRR8N5qkqcrUDYZ75kCUMT3TwQERWOdUn6Zw0VoKTeLdKp53yIb
8UEKar82otcOANP7myxySUg1zHzAynyabn/F96n95xf7awYR+lRxbEv9L821LGD0
tMcQxsbM4Q+d9XJxs9mkUtSi4iuUR+lR7QCZSPuhiBSKmzUDrjlXkeu4nfqWtFjQ
wlfToiF8MwaGfNpqEYcRpi1cMXH13TV7VIDv5MdIRsaR/r7IWFwznaNFixrT4gNg
a3HArpaSFI+XBagwtcHYGb/l4b3uvULFOjc40yXsxrZQuss8dPREi3uAwwxY0rPw
BVjI6pOQohHykbdplt0OZlOwvkMPyL8Wnn63E7Lk71PijepPbPk9OzVKPJ/eqy2n
gtvxs7BgfPDh3fvqCGFdFpBZ6aRjNG3DBivRdA9Pwn2Q6vuSslQ=
=VaY3
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-dt-for-v4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM64 Based SoC DT Updates for v4.16" from Simon Horman:
* Use r8a77970 (V3M) CPG core clock and SYSC power domain macros
These may be used in place of numeric constants now that they
are present in Linus's tree.
* Add r8a77970 (V3M) Starter Kit board support
This includes basic support to bring up the board with a serial
console and EtherAVB support
* Add IPMMU nodes and connections to on-chip devices
on r8a7795 (H3), r8a7796 (M3-W), r8a77970 (V3M) and r8a77995 (D3) SoCs
Simon Horman says "With these patches applied a white list enabled IPMMU
driver may be used to check silicon revision and then enable IPMMU in the
known working cases."
* Enable DMA for SCIF2 on r8a77995 (D2) SoC
* Increase the number of GPIO bank 1 ports to 29 on r8a7795 (H3) SoC
This adds support for the GP-1-28 port pin of the r8a7795 (H3) ES2.0 SoC
* Add support for CAN to r8a77995 (D3) SoC
Ulrich Hecht says "This is a by-the-datasheet implementation, with the
datasheet missing some bits, namely the pin map. I filled in the gaps...
by deducing the information from pin numbers already in the PFC driver,
so careful scrutiny is advised."
* Add support for SDHI to r8a77995 (D3) SoC
* Add SoC name to file header of r8a7795 (H3) and r8a7796 (M3-W)
Salvator-X and Salvator-XS board files
Geert Uytterhoeven says "With the proliferation of Salvator-X and
Salvator-XS boards carrying different R-Car Gen3 SoCs variants, several
DTS files ended up having the same file headers.
Add the SoC names to the file headers to avoid confusion."
* Add device note for ROHM BD9571MWV PMIC to
r8a7795 (H3) and r8a7796 (M3-W) Salvator-X and Salvator-XS boards.
Geert Uytterhoeven says "This was based on the example in the DT binding
documentation, but using IRQ0 instead of a GPIO interrupt, as that
matches the schematics, and because INTC-EX is a simpler block."
* Enable USB2.0 channel 0 on r8a77970 (V3M) ULCB Kingfisher board
Vladimir Barinov says "The dedicated USB0_PWEN pin is used to control
CN13 VBUS source from U43 power supply. MAX3355 can also provide VBUS,
hence it should be disabled via OTG_OFFVBUSn node coming from gpio
expander TCA9539. Set MAX3355 enabled using OTG_EXTLPn node to be able
to read OTG ID of CN13."
* Add support for r8a7795 (M3-W) Salvator-XS board
Geert Uytterhoeven says "This patch series adds support for the version
of the Salvator-XS development board equipped with an R-Car M3-W SiP.
The DT was based on work for the Salvator-X and -XS boards with M3-W
resp. H3 SiPs."
* Add watchdog timer support to r8a77970 (V3M) eagle board
Geert Uytterhoven says "This allows to use the watchdog timer to reset
the board, until PSCI is enhanced to include such functionality."
* Use Use R-Car SDHI Gen3 fallback on r8a7795 (H3) and r8a7796 (M3-W) SoCs
* Set driver type for MMC on r8a7795 (H3) and r8a7796 (M3-W) Salvator-X and
Salvator-XS boards.
Wolfram Sang says "These boards are known to have eMMC issues with the
default driver type. Specify a working one."
* tag 'renesas-arm64-dt-for-v4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (54 commits)
arm64: dts: renesas: r8a77970: use SYSC power domain macros
arm64: dts: renesas: r8a77970: use CPG core clock macros
arm64: dts: renesas: v3msk: add EtherAVB support
arm64: dts: renesas: initial V3MSK board device tree
arm64: dts: renesas: r8a77995: Connect Ethernet-AVB to IPMMU-RT
arm64: dts: renesas: r8a77995: Add IPMMU device nodes
arm64: dts: renesas: r8a77970: Enable IPMMU-DS1, RT and MM
arm64: dts: renesas: r8a77970: Connect Ethernet-AVB to IPMMU-RT
arm64: dts: renesas: r8a77970: Tie SYS-DMAC to IPMMU-DS1
arm64: dts: renesas: r8a77970: Add IPMMU device nodes
arm64: dts: renesas: r8a77995: add DMA for SCIF2
arm64: dts: renesas: r8a77970: sort includes
arm64: dts: renesas: r8a7795: Increase the number of GPIO bank 1 ports to 29
arm64: dts: renesas: r8a77995: Add CAN FD support
arm64: dts: renesas: r8a77995: Add CAN support
arm64: dts: renesas: r8a77995: Add CAN external clock support
arm64: dts: renesas: r8a7795-salvator-xs: Add SoC name to file header
arm64: dts: renesas: r8a7796-salvator-x: Add SoC name to file header
arm64: dts: renesas: r8a7795-salvator-x: Add SoC name to file header
arm64: dts: renesas: r8a7795-es1-salvator-x: Add SoC name to file header
...
Blink the LED on a kernel panic.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Guodong Xu <guodong.xu@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Blink the LED on a kernel panic.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Guodong Xu <guodong.xu@linaro.org>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Blink the LED on a kernel panic.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Most development boards and devices have one or more LEDs. It is useful
during debugging if they can be wired to show different behaviours such as
disk or cpu activity or a load-average dependent heartbeat. Enable panic
and disk activity triggers so they can be tied to LED activity during
debugging as well.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the cpu frequency scaling support for Armada 37xx by default, this
should allow a better coverage in kernel continuous integration tests.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add opp v2 information,
and also add clocks, regulators and opp information into cpu nodes
Signed-off-by: Andrew-sh Cheng <andrew-sh.cheng@mediatek.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add clock controller nodes for MT2712, include topckgen, infracfg,
pericfg, mcucfg and apmixedsys. This patch also add six oscillators that
provide clocks for MT2712.
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add opp v2 information,
and also add clocks, regulators and opp information into cpu nodes
Signed-off-by: Andrew-sh Cheng <andrew-sh.cheng@mediatek.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch enables usb3_peri0 that uses usb3_phy0 to enable VBUS
detection for the USB3.0 peripheral.
The Salvator-X[S] has USB3.0 type-A connector and supplies VBUS
if USB3.0 host runs. So, you need a special cable for it, and
to stop the VBUS supplies from the board, after you installs
a gadget driver, you should run the following command to avoid
conflict VBUS supply:
# echo 1 > /sys/kernel/debug/ee020000.usb/b_device
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables usb3_phy0 node for Salvator-X[S].
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
It adds device mmc@9820000 which is used as SD card on poplar board.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
This patch adds an efuse node in the device tree for rk3228 SoC.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
fix the following issue:
arch/arm64/net/bpf_jit_comp.c: In function 'bpf_int_jit_compile':
arch/arm64/net/bpf_jit_comp.c:982:18: error: 'image_size' may be used
uninitialized in this function [-Werror=maybe-uninitialized]
Fixes: db496944fd ("bpf: arm64: add JIT support for multi-function programs")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2017-12-18
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Allow arbitrary function calls from one BPF function to another BPF function.
As of today when writing BPF programs, __always_inline had to be used in
the BPF C programs for all functions, unnecessarily causing LLVM to inflate
code size. Handle this more naturally with support for BPF to BPF calls
such that this __always_inline restriction can be overcome. As a result,
it allows for better optimized code and finally enables to introduce core
BPF libraries in the future that can be reused out of different projects.
x86 and arm64 JIT support was added as well, from Alexei.
2) Add infrastructure for tagging functions as error injectable and allow for
BPF to return arbitrary error values when BPF is attached via kprobes on
those. This way of injecting errors generically eases testing and debugging
without having to recompile or restart the kernel. Tags for opting-in for
this facility are added with BPF_ALLOW_ERROR_INJECTION(), from Josef.
3) For BPF offload via nfp JIT, add support for bpf_xdp_adjust_head() helper
call for XDP programs. First part of this work adds handling of BPF
capabilities included in the firmware, and the later patches add support
to the nfp verifier part and JIT as well as some small optimizations,
from Jakub.
4) The bpftool now also gets support for basic cgroup BPF operations such
as attaching, detaching and listing current BPF programs. As a requirement
for the attach part, bpftool can now also load object files through
'bpftool prog load'. This reuses libbpf which we have in the kernel tree
as well. bpftool-cgroup man page is added along with it, from Roman.
5) Back then commit e87c6bc385 ("bpf: permit multiple bpf attachments for
a single perf event") added support for attaching multiple BPF programs
to a single perf event. Given they are configured through perf's ioctl()
interface, the interface has been extended with a PERF_EVENT_IOC_QUERY_BPF
command in this work in order to return an array of one or multiple BPF
prog ids that are currently attached, from Yonghong.
6) Various minor fixes and cleanups to the bpftool's Makefile as well
as a new 'uninstall' and 'doc-uninstall' target for removing bpftool
itself or prior installed documentation related to it, from Quentin.
7) Add CONFIG_CGROUP_BPF=y to the BPF kernel selftest config file which is
required for the test_dev_cgroup test case to run, from Naresh.
8) Fix reporting of XDP prog_flags for nfp driver, from Jakub.
9) Fix libbpf's exit code from the Makefile when libelf was not found in
the system, also from Jakub.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add reg properties to pciec[01] placeholder nodes
This is to stop the compiler complaining as follows:
$ make
...
DTC arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@fe000000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@ee800000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (simple_bus_reg): Node /soc/pcie@fe000000 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (simple_bus_reg): Node /soc/pcie@ee800000 missing or empty reg/ranges property
DTC arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dtb
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@fe000000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@ee800000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dtb: Warning (simple_bus_reg): Node /soc/pcie@fe000000 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dtb: Warning (simple_bus_reg): Node /soc/pcie@ee800000 missing or empty reg/ranges property
DTC arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dtb
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@fe000000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@ee800000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dtb: Warning (simple_bus_reg): Node /soc/pcie@fe000000 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dtb: Warning (simple_bus_reg): Node /soc/pcie@ee800000 missing or empty reg/ranges property
DTC arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb
arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@fe000000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (unit_address_vs_reg): Node /soc/pcie@ee800000 has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (simple_bus_reg): Node /soc/pcie@fe000000 missing or empty reg/ranges property
arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (simple_bus_reg): Node /soc/pcie@ee800000 missing or empty reg/ranges property
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
In order to be able to use cpu freq, we need to associate a clock to each
CPU and to expose the power management registers.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add NAND support on the Armada-8040-DB by adding the same tree as for
the Armada-7040-DB by using the same compatible string
"marvell,armada-8k-nand".
Do not enable the NAND node as enabling it (and changing manually the
proper DPR-76 switch) would disable MDIO from CP1 (and thus disable CPS
Ethernet PHY).
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
When VHE is not present, KVM needs to save and restores PMSCR_EL1 when
possible. If SPE is used by the host, value of PMSCR_EL1 cannot be saved
for the guest.
If the host starts using SPE between two save+restore on the same vcpu,
restore will write the value of PMSCR_EL1 read during the first save.
Make sure __debug_save_spe_nvhe clears the value of the saved PMSCR_EL1
when the guest cannot use SPE.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
similar to x64 add support for bpf-to-bpf calls.
When program has calls to in-kernel helpers the target call offset
is known at JIT time and arm64 architecture needs 2 passes.
With bpf-to-bpf calls the dynamically allocated function start
is unknown until all functions of the program are JITed.
Therefore (just like x64) arm64 JIT needs one extra pass over
the program to emit correct call offsets.
Implementation detail:
Avoid being too clever in 64-bit immediate moves and
always use 4 instructions (instead of 3-4 depending on the address)
to make sure only one extra pass is needed.
If some future optimization would make it worth while to optimize
'call 64-bit imm' further, the JIT would need to do 4 passes
over the program instead of 3 as in this patch.
For typical bpf program address the mov needs 3 or 4 insns,
so unconditional 4 insns to save extra pass is a worthy trade off
at this state of JIT.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
global bpf_jit_enable variable is tested multiple times in JITs,
blinding and verifier core. The malicious root can try to toggle
it while loading the programs. This race condition was accounted
for and there should be no issues, but it's safer to avoid
this race condition.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Enable tcphy and create the cros-ec's extcon node for the USB Type-C port.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the usb3 phyter for the USB3.0 OTG controller.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
After commit '06c47e6286d usb: dwc3: of-simple: Add support to get resets
for the device' you can add the reset property to the dwc3 node, the reset
is required for the controller to work properly, otherwise bind / unbind
stress testing of the USB controller on rk3399 we'd often end up with lots
of failures that looked like this:
phy phy-ff800000.phy.9: phy poweron failed --> -110
dwc3 fe900000.dwc3: failed to initialize core
dwc3: probe of fe900000.dwc3 failed with error -110
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The aclk_usb3 must be enabled to support USB3 for rk3399.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the usb3 power-domain, its qos area and assign it to the usb device
node.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add PWM DT info for the Amlogic's Meson-Axg SoC.
Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add new pinctrl DT info for the Amlogic's Meson-AXG SoC.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
[khilman: dropped unnecessary include]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Try to add Hiubus DT info, and also enable clock DT info
for the Amlogic's Meson-AXG SoC.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Qiufang Dai <qiufang.dai@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Commit 9de52a755c ("arm64: fpsimd: Fix failure to restore FPSIMD
state after signals") fixed an issue reported in our FPSIMD signal
restore code but inadvertently introduced another issue which tends to
manifest as random SEGVs in userspace.
The problem is that when we copy the struct fpsimd_state from the kernel
stack (populated from the signal frame) into the struct held in the
current thread_struct, we blindly copy uninitialised stack into the
"cpu" field, which means that context-switching of the FP registers is
no longer reliable.
This patch fixes the problem by copying only the user_fpsimd member of
struct fpsimd_state. We should really rework the function prototypes
to take struct user_fpsimd_state * instead, but let's just get this
fixed for now.
Cc: Dave Martin <Dave.Martin@arm.com>
Fixes: 9de52a755c ("arm64: fpsimd: Fix failure to restore FPSIMD state after signals")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Use the sor1_out clock instead of sor1_src. This is a more accurate
model of the hardware and allows for more complicated configurations
such as HDMI 2.0.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently, the SVE field in ID_AA64PFR0_EL1 is visible
unconditionally to userspace via the CPU ID register emulation,
irrespective of the kernel config. This means that if a kernel
configured with CONFIG_ARM64_SVE=n is run on SVE-capable hardware,
userspace will see SVE reported as present in the ID regs even
though the kernel forbids execution of SVE instructions.
This patch makes the exposure of the SVE field in ID_AA64PFR0_EL1
conditional on CONFIG_ARM64_SVE=y.
Since future architecture features are likely to encounter a
similar requirement, this patch adds a suitable helper macros for
use when declaring config-conditional ID register fields.
Fixes: 43994d824e ("arm64/sve: Detect SVE and activate runtime support")
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Cc: Suzuki Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In ptdump_check_wx(), we pass walk_pgd() a start address of 0 (rather
than VA_START) for the init_mm. This means that any reported W&X
addresses are offset by VA_START, which is clearly wrong and can make
them appear like userspace addresses.
Fix this by telling the ptdump code that we're walking init_mm starting
at VA_START. We don't need to update the addr_markers, since these are
still valid bounds regardless.
Cc: <stable@vger.kernel.org>
Fixes: 1404d6f13e ("arm64: dump: Add checking for writable and exectuable pages")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Laura Abbott <labbott@redhat.com>
Reported-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Move vcpu_load() and vcpu_put() into the architecture specific
implementations of kvm_arch_vcpu_ioctl_set_guest_debug().
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the CPU and PSCI nodes for the NVIDIA Tegra210 platforms so that
all CPUs can be enabled on boot. This assumes that the PSCI firmware
has been loaded during the initial bootstrap on the device before the
kernel starts (which is typically the case for these platforms). The
PSCI firmware version is set to v0.2 which aligns with the current
shipping version for Tegra.
Reported-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Tested-By: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable the host1x and necessary children and hook up the HDMI +5V pin to
enable video output on the HDMI port found on Jetson TX2.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Adds the device tree nodes for the display hub and display controllers
as well as the DPAUX, DSI and SOR controllers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the DT node for ARM SMMU on Tegra186.
Signed-off-by: Krishna Reddy <vdumpa@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The FUSE register block found on Tegra186 SoCs encodes various settings,
such as calibration data for other blocks.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The MISC register block found on Tegra186 SoCs contains registers that
can be used to identify a given chip and various strapping options.
Signed-off-by: Thierry Reding <treding@nvidia.com>
do_sea() calls arm64_notify_die() which will always signal
user-space. It also returns whether APEI claimed the external
abort as a RAS notification. If it returns failure do_mem_abort()
will signal user-space too.
do_mem_abort() wants to know if we handled the error, we always
call arm64_notify_die() so can always return success.
Signed-off-by: Dongjiu Geng <gengdongjiu@huawei.com>
Reviewed-by: James Morse <james.morse@arm.com>
Reviewed-by: Xie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
