Switching merge_across_nodes after running KSM is liable to oops on stale
nodes still left over from the previous stable tree. It's not something
that people will often want to do, but it would be lame to demand a reboot
when they're trying to determine which merge_across_nodes setting is best.
How can this happen? We only permit switching merge_across_nodes when
pages_shared is 0, and usually set run 2 to force that beforehand, which
ought to unmerge everything: yet oopses still occur when you then run 1.
Three causes:
1. The old stable tree (built according to the inverse
merge_across_nodes) has not been fully torn down. A stable node
lingers until get_ksm_page() notices that the page it references no
longer references it: but the page is not necessarily freed as soon as
expected, particularly when swapcache.
Fix this with a pass through the old stable tree, applying
get_ksm_page() to each of the remaining nodes (most found stale and
removed immediately), with forced removal of any left over. Unless the
page is still mapped: I've not seen that case, it shouldn't occur, but
better to WARN_ON_ONCE and EBUSY than BUG.
2. __ksm_enter() has a nice little optimization, to insert the new mm
just behind ksmd's cursor, so there's a full pass for it to stabilize
(or be removed) before ksmd addresses it. Nice when ksmd is running,
but not so nice when we're trying to unmerge all mms: we were missing
those mms forked and inserted behind the unmerge cursor. Easily fixed
by inserting at the end when KSM_RUN_UNMERGE.
3. It is possible for a KSM page to be faulted back from swapcache
into an mm, just after unmerge_and_remove_all_rmap_items() scanned past
it. Fix this by copying on fault when KSM_RUN_UNMERGE: but that is
private to ksm.c, so dissolve the distinction between
ksm_might_need_to_copy() and ksm_does_need_to_copy(), doing it all in
the one call into ksm.c.
A long outstanding, unrelated bugfix sneaks in with that third fix:
ksm_does_need_to_copy() would copy from a !PageUptodate page (implying I/O
error when read in from swap) to a page which it then marks Uptodate. Fix
this case by not copying, letting do_swap_page() discover the error.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Petr Holasek <pholasek@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Izik Eidus <izik.eidus@ravellosystems.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function names page_xchg_last_nid(), page_last_nid() and
reset_page_last_nid() were judged to be inconsistent so rename them to a
struct_field_op style pattern. As it looked jarring to have
reset_page_mapcount() and page_nid_reset_last() beside each other in
memmap_init_zone(), this patch also renames reset_page_mapcount() to
page_mapcount_reset(). There are others like init_page_count() but as
it is used throughout the arch code a rename would likely cause more
conflicts than it is worth.
[akpm@linux-foundation.org: fix zcache]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton pointed out that page_xchg_last_nid() and
reset_page_last_nid() were "getting nuttily large" and asked that it be
investigated.
reset_page_last_nid() is on the page free path and it would be
unfortunate to make that path more expensive than it needs to be. Due
to the internal use of page_xchg_last_nid() it is already too expensive
but fortunately, it should also be impossible for the page->flags to be
updated in parallel when we call reset_page_last_nid(). Instead of
unlining the function, it uses a simplier implementation that assumes no
parallel updates and should now be sufficiently short for inlining.
page_xchg_last_nid() is called in paths that are already quite expensive
(splitting huge page, fault handling, migration) and it is reasonable to
uninline. There was not really a good place to place the function but
mm/mmzone.c was the closest fit IMO.
This patch saved 128 bytes of text in the vmlinux file for the kernel
configuration I used for testing automatic NUMA balancing.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When calculating amount of dirtyable memory, min_free_kbytes should be
subtracted because it is not intended for dirty pages.
Addresses http://bugs.debian.org/695182
[akpm@linux-foundation.org: fix up min_free_kbytes extern declarations]
[akpm@linux-foundation.org: fix min() warning]
Signed-off-by: Paul Szabo <psz@maths.usyd.edu.au>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The comment in commit 4fc3f1d66b ("mm/rmap, migration: Make
rmap_walk_anon() and try_to_unmap_anon() more scalable") says:
| Rename anon_vma_[un]lock() => anon_vma_[un]lock_write(),
| to make it clearer that it's an exclusive write-lock in
| that case - suggested by Rik van Riel.
But that commit renames only anon_vma_lock()
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
swap_lock is heavily contended when I test swap to 3 fast SSD (even
slightly slower than swap to 2 such SSD). The main contention comes
from swap_info_get(). This patch tries to fix the gap with adding a new
per-partition lock.
Global data like nr_swapfiles, total_swap_pages, least_priority and
swap_list are still protected by swap_lock.
nr_swap_pages is an atomic now, it can be changed without swap_lock. In
theory, it's possible get_swap_page() finds no swap pages but actually
there are free swap pages. But sounds not a big problem.
Accessing partition specific data (like scan_swap_map and so on) is only
protected by swap_info_struct.lock.
Changing swap_info_struct.flags need hold swap_lock and
swap_info_struct.lock, because scan_scan_map() will check it. read the
flags is ok with either the locks hold.
If both swap_lock and swap_info_struct.lock must be hold, we always hold
the former first to avoid deadlock.
swap_entry_free() can change swap_list. To delete that code, we add a
new highest_priority_index. Whenever get_swap_page() is called, we
check it. If it's valid, we use it.
It's a pity get_swap_page() still holds swap_lock(). But in practice,
swap_lock() isn't heavily contended in my test with this patch (or I can
say there are other much more heavier bottlenecks like TLB flush). And
BTW, looks get_swap_page() doesn't really need the lock. We never free
swap_info[] and we check SWAP_WRITEOK flag. The only risk without the
lock is we could swapout to some low priority swap, but we can quickly
recover after several rounds of swap, so sounds not a big deal to me.
But I'd prefer to fix this if it's a real problem.
"swap: make each swap partition have one address_space" improved the
swapout speed from 1.7G/s to 2G/s. This patch further improves the
speed to 2.3G/s, so around 15% improvement. It's a multi-process test,
so TLB flush isn't the biggest bottleneck before the patches.
[arnd@arndb.de: fix it for nommu]
[hughd@google.com: add missing unlock]
[minchan@kernel.org: get rid of lockdep whinge on sys_swapon]
Signed-off-by: Shaohua Li <shli@fusionio.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Seth Jennings <sjenning@linux.vnet.ibm.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Cc: Dan Magenheimer <dan.magenheimer@oracle.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When I use several fast SSD to do swap, swapper_space.tree_lock is
heavily contended. This makes each swap partition have one
address_space to reduce the lock contention. There is an array of
address_space for swap. The swap entry type is the index to the array.
In my test with 3 SSD, this increases the swapout throughput 20%.
[akpm@linux-foundation.org: revert unneeded change to __add_to_swap_cache]
Signed-off-by: Shaohua Li <shli@fusionio.com>
Cc: Hugh Dickins <hughd@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
page->_last_nid fits into page->flags on 64-bit. The unlikely 32-bit
NUMA configuration with NUMA Balancing will still need an extra page
field. As Peter notes "Completely dropping 32bit support for
CONFIG_NUMA_BALANCING would simplify things, but it would also remove
the warning if we grow enough 64bit only page-flags to push the last-cpu
out."
[mgorman@suse.de: minor modifications]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Simon Jeons <simon.jeons@gmail.com>
Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a preparation patch for moving page->_last_nid into page->flags
that moves page flag layout information to a separate header. This
patch is necessary because otherwise there would be a circular
dependency between mm_types.h and mm.h.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Simon Jeons <simon.jeons@gmail.com>
Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current definitions for count_vm_numa_events() is wrong for
!CONFIG_NUMA_BALANCING as the following would miss the side-effect.
count_vm_numa_events(NUMA_FOO, bar++);
There are no such users of count_vm_numa_events() but this patch fixes
it as it is a potential pitfall. Ideally both would be converted to
static inline but NUMA_PTE_UPDATES is not defined if
!CONFIG_NUMA_BALANCING and creating dummy constants just to have a
static inline would be similarly clumsy.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Simon Jeons <simon.jeons@gmail.com>
Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
s/me/be/ and clarify the comment a bit when we're changing it anyway.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Suggested-by: Simon Jeons <simon.jeons@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce the flag memalloc_noio in 'struct dev_pm_info' to help PM core
to teach mm not allocating memory with GFP_KERNEL flag for avoiding
probable deadlock.
As explained in the comment, any GFP_KERNEL allocation inside
runtime_resume() or runtime_suspend() on any one of device in the path
from one block or network device to the root device in the device tree
may cause deadlock, the introduced pm_runtime_set_memalloc_noio() sets
or clears the flag on device in the path recursively.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Jiri Kosina <jiri.kosina@suse.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Decotigny <david.decotigny@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch introduces PF_MEMALLOC_NOIO on process flag('flags' field of
'struct task_struct'), so that the flag can be set by one task to avoid
doing I/O inside memory allocation in the task's context.
The patch trys to solve one deadlock problem caused by block device, and
the problem may happen at least in the below situations:
- during block device runtime resume, if memory allocation with
GFP_KERNEL is called inside runtime resume callback of any one of its
ancestors(or the block device itself), the deadlock may be triggered
inside the memory allocation since it might not complete until the block
device becomes active and the involed page I/O finishes. The situation
is pointed out first by Alan Stern. It is not a good approach to
convert all GFP_KERNEL[1] in the path into GFP_NOIO because several
subsystems may be involved(for example, PCI, USB and SCSI may be
involved for usb mass stoarage device, network devices involved too in
the iSCSI case)
- during block device runtime suspend, because runtime resume need to
wait for completion of concurrent runtime suspend.
- during error handling of usb mass storage deivce, USB bus reset will
be put on the device, so there shouldn't have any memory allocation with
GFP_KERNEL during USB bus reset, otherwise the deadlock similar with
above may be triggered. Unfortunately, any usb device may include one
mass storage interface in theory, so it requires all usb interface
drivers to handle the situation. In fact, most usb drivers don't know
how to handle bus reset on the device and don't provide .pre_set() and
.post_reset() callback at all, so USB core has to unbind and bind driver
for these devices. So it is still not practical to resort to GFP_NOIO
for solving the problem.
Also the introduced solution can be used by block subsystem or block
drivers too, for example, set the PF_MEMALLOC_NOIO flag before doing
actual I/O transfer.
It is not a good idea to convert all these GFP_KERNEL in the affected
path into GFP_NOIO because these functions doing that may be implemented
as library and will be called in many other contexts.
In fact, memalloc_noio_flags() can convert some of current static
GFP_NOIO allocation into GFP_KERNEL back in other non-affected contexts,
at least almost all GFP_NOIO in USB subsystem can be converted into
GFP_KERNEL after applying the approach and make allocation with GFP_NOIO
only happen in runtime resume/bus reset/block I/O transfer contexts
generally.
[1], several GFP_KERNEL allocation examples in runtime resume path
- pci subsystem
acpi_os_allocate
<-acpi_ut_allocate
<-ACPI_ALLOCATE_ZEROED
<-acpi_evaluate_object
<-__acpi_bus_set_power
<-acpi_bus_set_power
<-acpi_pci_set_power_state
<-platform_pci_set_power_state
<-pci_platform_power_transition
<-__pci_complete_power_transition
<-pci_set_power_state
<-pci_restore_standard_config
<-pci_pm_runtime_resume
- usb subsystem
usb_get_status
<-finish_port_resume
<-usb_port_resume
<-generic_resume
<-usb_resume_device
<-usb_resume_both
<-usb_runtime_resume
- some individual usb drivers
usblp, uvc, gspca, most of dvb-usb-v2 media drivers, cpia2, az6007, ....
That is just what I have found. Unfortunately, this allocation can only
be found by human being now, and there should be many not found since
any function in the resume path(call tree) may allocate memory with
GFP_KERNEL.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Jiri Kosina <jiri.kosina@suse.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Decotigny <david.decotigny@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
From: Zlatko Calusic <zlatko.calusic@iskon.hr>
Commit 92df3a723f ("mm: vmscan: throttle reclaim if encountering too
many dirty pages under writeback") introduced waiting on congested zones
based on a sane algorithm in shrink_inactive_list().
What this means is that there's no more need for throttling and
additional heuristics in balance_pgdat(). So, let's remove it and tidy
up the code.
Signed-off-by: Zlatko Calusic <zlatko.calusic@iskon.hr>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Johannes Weiner <jweiner@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since MCE is an x86 concept, and this code is in mm/, it would be better
to use the name num_poisoned_pages instead of mce_bad_pages.
[akpm@linux-foundation.org: fix mm/sparse.c]
Signed-off-by: Xishi Qiu <qiuxishi@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Suggested-by: Borislav Petkov <bp@alien8.de>
Reviewed-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several functions test MIGRATE_ISOLATE and some of those are hotpath but
MIGRATE_ISOLATE is used only if we enable CONFIG_MEMORY_ISOLATION(ie,
CMA, memory-hotplug and memory-failure) which are not common config
option. So let's not add unnecessary overhead and code when we don't
enable CONFIG_MEMORY_ISOLATION.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The definition of struct movablecore_map is protected by
CONFIG_HAVE_MEMBLOCK_NODE_MAP but its use in memblock_overlaps_region()
is not. So add CONFIG_HAVE_MEMBLOCK_NODE_MAP to protect the use of
movablecore_map in memblock_overlaps_region().
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We now provide an option for users who don't want to specify physical
memory address in kernel commandline.
/*
* For movablemem_map=acpi:
*
* SRAT: |_____| |_____| |_________| |_________| ......
* node id: 0 1 1 2
* hotpluggable: n y y n
* movablemem_map: |_____| |_________|
*
* Using movablemem_map, we can prevent memblock from allocating memory
* on ZONE_MOVABLE at boot time.
*/
So user just specify movablemem_map=acpi, and the kernel will use
hotpluggable info in SRAT to determine which memory ranges should be set
as ZONE_MOVABLE.
If all the memory ranges in SRAT is hotpluggable, then no memory can be
used by kernel. But before parsing SRAT, memblock has already reserve
some memory ranges for other purposes, such as for kernel image, and so
on. We cannot prevent kernel from using these memory. So we need to
exclude these ranges even if these memory is hotpluggable.
Furthermore, there could be several memory ranges in the single node
which the kernel resides in. We may skip one range that have memory
reserved by memblock, but if the rest of memory is too small, then the
kernel will fail to boot. So, make the whole node which the kernel
resides in un-hotpluggable. Then the kernel has enough memory to use.
NOTE: Using this way will cause NUMA performance down because the
whole node will be set as ZONE_MOVABLE, and kernel cannot use memory
on it. If users don't want to lose NUMA performance, just don't use
it.
[akpm@linux-foundation.org: fix warning]
[akpm@linux-foundation.org: use strcmp()]
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When implementing movablemem_map boot option, we introduced an array
movablemem_map.map[] to store the memory ranges to be set as
ZONE_MOVABLE.
Since ZONE_MOVABLE is the latst zone of a node, if user didn't specify
the whole node memory range, we need to extend it to the node end so
that we can use it to prevent memblock from allocating memory in the
ranges user didn't specify.
We now implement movablemem_map boot option like this:
/*
* For movablemem_map=nn[KMG]@ss[KMG]:
*
* SRAT: |_____| |_____| |_________| |_________| ......
* node id: 0 1 1 2
* user specified: |__| |___|
* movablemem_map: |___| |_________| |______| ......
*
* Using movablemem_map, we can prevent memblock from allocating memory
* on ZONE_MOVABLE at boot time.
*
* NOTE: In this case, SRAT info will be ingored.
*/
[akpm@linux-foundation.org: clean up code, fix build warning]
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On linux, the pages used by kernel could not be migrated. As a result,
if a memory range is used by kernel, it cannot be hot-removed. So if we
want to hot-remove memory, we should prevent kernel from using it.
The way now used to prevent this is specify a memory range by
movablemem_map boot option and set it as ZONE_MOVABLE.
But when the system is booting, memblock will allocate memory, and
reserve the memory for kernel. And before we parse SRAT, and know the
node memory ranges, memblock is working. And it may allocate memory in
ranges to be set as ZONE_MOVABLE. This memory can be used by kernel,
and never be freed.
So, let's parse SRAT before memblock is called first. And it is early
enough.
The first call of memblock_find_in_range_node() is in:
setup_arch()
|-->setup_real_mode()
so, this patch add a function early_parse_srat() to parse SRAT, and call
it before setup_real_mode() is called.
NOTE:
1) early_parse_srat() is called before numa_init(), and has initialized
numa_meminfo. So DO NOT clear numa_nodes_parsed in numa_init() and DO
NOT zero numa_meminfo in numa_init(), otherwise we will lose memory
numa info.
2) I don't know why using count of memory affinities parsed from SRAT
as a return value in original acpi_numa_init(). So I add a static
variable srat_mem_cnt to remember this count and use it as the return
value of the new acpi_numa_init()
[mhocko@suse.cz: parse SRAT before memblock is ready fix]
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Reviewed-by: Wen Congyang <wency@cn.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ensure the bootmem will not allocate memory from areas that may be
ZONE_MOVABLE. The map info is from movablecore_map boot option.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Reviewed-by: Wen Congyang <wency@cn.fujitsu.com>
Reviewed-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Tested-by: Lin Feng <linfeng@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add functions to parse movablemem_map boot option. Since the option
could be specified more then once, all the maps will be stored in the
global variable movablemem_map.map array.
And also, we keep the array in monotonic increasing order by start_pfn.
And merge all overlapped ranges.
[akpm@linux-foundation.org: improve comment]
[akpm@linux-foundation.org: checkpatch fixes]
[akpm@linux-foundation.org: remove unneeded parens]
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Reviewed-by: Wen Congyang <wency@cn.fujitsu.com>
Tested-by: Lin Feng <linfeng@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
try_offline_node() will be needed in the tristate
drivers/acpi/processor_driver.c.
The node will be offlined when all memory/cpu on the node have been
hotremoved. So we need the function try_offline_node() in cpu-hotplug
path.
If the memory-hotplug is disabled, and cpu-hotplug is enabled
1. no memory no the node
we don't online the node, and cpu's node is the nearest node.
2. the node contains some memory
the node has been onlined, and cpu's node is still needed
to migrate the sleep task on the cpu to the same node.
So we do nothing in try_offline_node() in this case.
[rientjes@google.com: export the function try_offline_node() fix]
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Jiang Liu <liuj97@gmail.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce a new function try_offline_node() to remove sysfs file of node
when all memory sections of this node are removed. If some memory
sections of this node are not removed, this function does nothing.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce a new API vmemmap_free() to free and remove vmemmap
pagetables. Since pagetable implements are different, each architecture
has to provide its own version of vmemmap_free(), just like
vmemmap_populate().
Note: vmemmap_free() is not implemented for ia64, ppc, s390, and sparc.
[mhocko@suse.cz: fix implicit declaration of remove_pagetable]
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Jianguo Wu <wujianguo@huawei.com>
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When memory is removed, the corresponding pagetables should alse be
removed. This patch introduces some common APIs to support vmemmap
pagetable and x86_64 architecture direct mapping pagetable removing.
All pages of virtual mapping in removed memory cannot be freed if some
pages used as PGD/PUD include not only removed memory but also other
memory. So this patch uses the following way to check whether a page
can be freed or not.
1) When removing memory, the page structs of the removed memory are
filled with 0FD.
2) All page structs are filled with 0xFD on PT/PMD, PT/PMD can be
cleared. In this case, the page used as PT/PMD can be freed.
For direct mapping pages, update direct_pages_count[level] when we freed
their pagetables. And do not free the pages again because they were
freed when offlining.
For vmemmap pages, free the pages and their pagetables.
For larger pages, do not split them into smaller ones because there is
no way to know if the larger page has been split. As a result, there is
no way to decide when to split. We deal the larger pages in the
following way:
1) For direct mapped pages, all the pages were freed when they were
offlined. And since menmory offline is done section by section, all
the memory ranges being removed are aligned to PAGE_SIZE. So only need
to deal with unaligned pages when freeing vmemmap pages.
2) For vmemmap pages being used to store page_struct, if part of the
larger page is still in use, just fill the unused part with 0xFD. And
when the whole page is fulfilled with 0xFD, then free the larger page.
[akpm@linux-foundation.org: fix typo in comment]
[tangchen@cn.fujitsu.com: do not calculate direct mapping pages when freeing vmemmap pagetables]
[tangchen@cn.fujitsu.com: do not free direct mapping pages twice]
[tangchen@cn.fujitsu.com: do not free page split from hugepage one by one]
[tangchen@cn.fujitsu.com: do not split pages when freeing pagetable pages]
[akpm@linux-foundation.org: use pmd_page_vaddr()]
[akpm@linux-foundation.org: fix used-uninitialised bug]
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Jianguo Wu <wujianguo@huawei.com>
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For removing memmap region of sparse-vmemmap which is allocated bootmem,
memmap region of sparse-vmemmap needs to be registered by
get_page_bootmem(). So the patch searches pages of virtual mapping and
registers the pages by get_page_bootmem().
NOTE: register_page_bootmem_memmap() is not implemented for ia64,
ppc, s390, and sparc. So introduce CONFIG_HAVE_BOOTMEM_INFO_NODE
and revert register_page_bootmem_info_node() when platform doesn't
support it.
It's implemented by adding a new Kconfig option named
CONFIG_HAVE_BOOTMEM_INFO_NODE, which will be automatically selected
by memory-hotplug feature fully supported archs(currently only on
x86_64).
Since we have 2 config options called MEMORY_HOTPLUG and
MEMORY_HOTREMOVE used for memory hot-add and hot-remove separately,
and codes in function register_page_bootmem_info_node() are only
used for collecting infomation for hot-remove, so reside it under
MEMORY_HOTREMOVE.
Besides page_isolation.c selected by MEMORY_ISOLATION under
MEMORY_HOTPLUG is also such case, move it too.
[mhocko@suse.cz: put register_page_bootmem_memmap inside CONFIG_MEMORY_HOTPLUG_SPARSE]
[linfeng@cn.fujitsu.com: introduce CONFIG_HAVE_BOOTMEM_INFO_NODE and revert register_page_bootmem_info_node()]
[mhocko@suse.cz: remove the arch specific functions without any implementation]
[linfeng@cn.fujitsu.com: mm/Kconfig: move auto selects from MEMORY_HOTPLUG to MEMORY_HOTREMOVE as needed]
[rientjes@google.com: fix defined but not used warning]
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Reviewed-by: Wu Jianguo <wujianguo@huawei.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Lin Feng <linfeng@cn.fujitsu.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For removing memory, we need to remove page tables. But it depends on
architecture. So the patch introduce arch_remove_memory() for removing
page table. Now it only calls __remove_pages().
Note: __remove_pages() for some archtecuture is not implemented
(I don't know how to implement it for s390).
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When (hot)adding memory into system, /sys/firmware/memmap/X/{end, start,
type} sysfs files are created. But there is no code to remove these
files. This patch implements the function to remove them.
We cannot free firmware_map_entry which is allocated by bootmem because
there is no way to do so when the system is up. But we can at least
remember the address of that memory and reuse the storage when the
memory is added next time.
This patch also introduces a new list map_entries_bootmem to link the
map entries allocated by bootmem when they are removed, and a lock to
protect it. And these entries will be reused when the memory is
hot-added again.
The idea is suggestted by Andrew Morton.
NOTE: It is unsafe to return an entry pointer and release the
map_entries_lock. So we should not hold the map_entries_lock
separately in firmware_map_find_entry() and
firmware_map_remove_entry(). Hold the map_entries_lock across find
and remove /sys/firmware/memmap/X operation.
And also, users of these two functions need to be careful to
hold the lock when using these two functions.
[tangchen@cn.fujitsu.com: Hold spinlock across find|remove /sys operation]
[tangchen@cn.fujitsu.com: fix the wrong comments of map_entries]
[tangchen@cn.fujitsu.com: reuse the storage of /sys/firmware/memmap/X/ allocated by bootmem]
[tangchen@cn.fujitsu.com: fix section mismatch problem]
[tangchen@cn.fujitsu.com: fix the doc format in drivers/firmware/memmap.c]
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Reviewed-by: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We remove the memory like this:
1. lock memory hotplug
2. offline a memory block
3. unlock memory hotplug
4. repeat 1-3 to offline all memory blocks
5. lock memory hotplug
6. remove memory(TODO)
7. unlock memory hotplug
All memory blocks must be offlined before removing memory. But we don't
hold the lock in the whole operation. So we should check whether all
memory blocks are offlined before step6. Otherwise, kernel maybe
panicked.
Offlining a memory block and removing a memory device can be two
different operations. Users can just offline some memory blocks without
removing the memory device. For this purpose, the kernel has held
lock_memory_hotplug() in __offline_pages(). To reuse the code for
memory hot-remove, we repeat step 1-3 to offline all the memory blocks,
repeatedly lock and unlock memory hotplug, but not hold the memory
hotplug lock in the whole operation.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
do_mmap_pgoff() rounds up the desired size to the next PAGE_SIZE
multiple, however there was no equivalent code in mm_populate(), which
caused issues.
This could be fixed by introduced the same rounding in mm_populate(),
however I think it's preferable to make do_mmap_pgoff() return populate
as a size rather than as a boolean, so we don't have to duplicate the
size rounding logic in mm_populate().
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Tested-by: Andy Lutomirski <luto@amacapital.net>
Cc: Greg Ungerer <gregungerer@westnet.com.au>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The vm_populate() code populates user mappings without constantly
holding the mmap_sem. This makes it susceptible to racy userspace
programs: the user mappings may change while vm_populate() is running,
and in this case vm_populate() may end up populating the new mapping
instead of the old one.
In order to reduce the possibility of userspace getting surprised by
this behavior, this change introduces the VM_POPULATE vma flag which
gets set on vmas we want vm_populate() to work on. This way
vm_populate() may still end up populating the new mapping after such a
race, but only if the new mapping is also one that the user has
requested (using MAP_SHARED, MAP_LOCKED or mlock) to be populated.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Tested-by: Andy Lutomirski <luto@amacapital.net>
Cc: Greg Ungerer <gregungerer@westnet.com.au>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In find_extend_vma(), we don't need mlock_vma_pages_range() to verify
the vma type - we know we're working with a stack. So, we can call
directly into __mlock_vma_pages_range(), and remove the last
make_pages_present() call site.
Note that we don't use mm_populate() here, so we can't release the
mmap_sem while allocating new stack pages. This is deemed acceptable,
because the stack vmas grow by a bounded number of pages at a time, and
these are anon pages so we don't have to read from disk to populate
them.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Tested-by: Andy Lutomirski <luto@amacapital.net>
Cc: Greg Ungerer <gregungerer@westnet.com.au>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After the MAP_POPULATE handling has been moved to mmap_region() call
sites, the only remaining use of the flags argument is to pass the
MAP_NORESERVE flag. This can be just as easily handled by
do_mmap_pgoff(), so do that and remove the mmap_region() flags
parameter.
[akpm@linux-foundation.org: remove double parens]
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Tested-by: Andy Lutomirski <luto@amacapital.net>
Cc: Greg Ungerer <gregungerer@westnet.com.au>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When creating new mappings using the MAP_POPULATE / MAP_LOCKED flags (or
with MCL_FUTURE in effect), we want to populate the pages within the
newly created vmas. This may take a while as we may have to read pages
from disk, so ideally we want to do this outside of the write-locked
mmap_sem region.
This change introduces mm_populate(), which is used to defer populating
such mappings until after the mmap_sem write lock has been released.
This is implemented as a generalization of the former do_mlock_pages(),
which accomplished the same task but was using during mlock() /
mlockall().
Signed-off-by: Michel Lespinasse <walken@google.com>
Reported-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Rik van Riel <riel@redhat.com>
Tested-by: Andy Lutomirski <luto@amacapital.net>
Cc: Greg Ungerer <gregungerer@westnet.com.au>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In certain cases (kswapd reclaim, memcg target reclaim), a fixed minimum
amount of pages is scanned from the LRU lists on each iteration, to make
progress.
Do not make this minimum bigger than the respective LRU list size,
however, and save some busy work trying to isolate and reclaim pages
that are not there.
Empty LRU lists are quite common with memory cgroups in NUMA
environments because there exists a set of LRU lists for each zone for
each memory cgroup, while the memory of a single cgroup is expected to
stay on just one node. The number of expected empty LRU lists is thus
memcgs * (nodes - 1) * lru types
Each attempt to reclaim from an empty LRU list does expensive size
comparisons between lists, acquires the zone's lru lock etc. Avoid
that.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Satoru Moriya <satoru.moriya@hds.com>
Cc: Simon Jeons <simon.jeons@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 mm changes from Peter Anvin:
"This is a huge set of several partly interrelated (and concurrently
developed) changes, which is why the branch history is messier than
one would like.
The *really* big items are two humonguous patchsets mostly developed
by Yinghai Lu at my request, which completely revamps the way we
create initial page tables. In particular, rather than estimating how
much memory we will need for page tables and then build them into that
memory -- a calculation that has shown to be incredibly fragile -- we
now build them (on 64 bits) with the aid of a "pseudo-linear mode" --
a #PF handler which creates temporary page tables on demand.
This has several advantages:
1. It makes it much easier to support things that need access to data
very early (a followon patchset uses this to load microcode way
early in the kernel startup).
2. It allows the kernel and all the kernel data objects to be invoked
from above the 4 GB limit. This allows kdump to work on very large
systems.
3. It greatly reduces the difference between Xen and native (Xen's
equivalent of the #PF handler are the temporary page tables created
by the domain builder), eliminating a bunch of fragile hooks.
The patch series also gets us a bit closer to W^X.
Additional work in this pull is the 64-bit get_user() work which you
were also involved with, and a bunch of cleanups/speedups to
__phys_addr()/__pa()."
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (105 commits)
x86, mm: Move reserving low memory later in initialization
x86, doc: Clarify the use of asm("%edx") in uaccess.h
x86, mm: Redesign get_user with a __builtin_choose_expr hack
x86: Be consistent with data size in getuser.S
x86, mm: Use a bitfield to mask nuisance get_user() warnings
x86/kvm: Fix compile warning in kvm_register_steal_time()
x86-32: Add support for 64bit get_user()
x86-32, mm: Remove reference to alloc_remap()
x86-32, mm: Remove reference to resume_map_numa_kva()
x86-32, mm: Rip out x86_32 NUMA remapping code
x86/numa: Use __pa_nodebug() instead
x86: Don't panic if can not alloc buffer for swiotlb
mm: Add alloc_bootmem_low_pages_nopanic()
x86, 64bit, mm: hibernate use generic mapping_init
x86, 64bit, mm: Mark data/bss/brk to nx
x86: Merge early kernel reserve for 32bit and 64bit
x86: Add Crash kernel low reservation
x86, kdump: Remove crashkernel range find limit for 64bit
memblock: Add memblock_mem_size()
x86, boot: Not need to check setup_header version for setup_data
...
Pull s390 update from Martin Schwidefsky:
"The most prominent change in this patch set is the software dirty bit
patch for s390. It removes __HAVE_ARCH_PAGE_TEST_AND_CLEAR_DIRTY and
the page_test_and_clear_dirty primitive which makes the common memory
management code a bit less obscure.
Heiko fixed most of the PCI related fallout, more often than not
missing GENERIC_HARDIRQS dependencies. Notable is one of the 3270
patches which adds an export to tty_io to be able to resize a tty.
The rest is the usual bunch of cleanups and bug fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (42 commits)
s390/module: Add missing R_390_NONE relocation type
drivers/gpio: add missing GENERIC_HARDIRQ dependency
drivers/input: add couple of missing GENERIC_HARDIRQS dependencies
s390/cleanup: rename SPP to LPP
s390/mm: implement software dirty bits
s390/mm: Fix crst upgrade of mmap with MAP_FIXED
s390/linker skript: discard exit.data at runtime
drivers/media: add missing GENERIC_HARDIRQS dependency
s390/bpf,jit: add vlan tag support
drivers/net,AT91RM9200: add missing GENERIC_HARDIRQS dependency
iucv: fix kernel panic at reboot
s390/Kconfig: sort list of arch selected config options
phylib: remove !S390 dependeny from Kconfig
uio: remove !S390 dependency from Kconfig
dasd: fix sysfs cleanup in dasd_generic_remove
s390/pci: fix hotplug module init
s390/pci: cleanup clp page allocation
s390/pci: cleanup clp inline assembly
s390/perf: cpum_cf: fallback to software sampling events
s390/mm: provide PAGE_SHARED define
...
Pull HID subsystem updates from Jiri Kosina:
"HID subsystem and drivers update. Highlights:
- new support of a group of Win7/Win8 multitouch devices, from
Benjamin Tissoires
- fix for compat interface brokenness in uhid, from Dmitry Torokhov
- conversion of drivers to use hid_driver helper, by H Hartley
Sweeten
- HID over I2C transport received ACPI enumeration support, written
by Mika Westerberg
- there is an ongoing effort to make HID sensor hubs independent of
USB transport. The first self-contained part of this work is
provided here, done by Mika Westerberg
- a few smaller fixes here and there, support for a couple new
devices added"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (43 commits)
HID: Correct Logitech order in hid-ids.h
HID: LG4FF: Remove unnecessary deadzone code
HID: LG: Prevent the Logitech Gaming Wheels deadzone
HID: LG: Fix detection of Logitech Speed Force Wireless (WiiWheel)
HID: LG: Add support for Logitech Momo Force (Red) Wheel
HID: hidraw: print message when succesfully initialized
HID: logitech: split accel, brake for Driving Force wheel
HID: logitech: add report descriptor for Driving Force wheel
HID: add ThingM blink(1) USB RGB LED support
HID: uhid: make creating devices work on 64/32 systems
HID: wiimote: fix nunchuck button parser
HID: blacklist Velleman data acquisition boards
HID: sensor-hub: don't limit the driver only to USB bus
HID: sensor-hub: get rid of unused sensor_hub_grabbed_usages[] table
HID: extend autodetect to handle I2C sensors as well
HID: ntrig: use input_configured() callback to set the name
HID: multitouch: do not use pointers towards hid-core
HID: add missing GENERIC_HARDIRQ dependency
HID: multitouch: make MT_CLS_ALWAYS_TRUE the new default class
HID: multitouch: fix protocol for Elo panels
...
Pull trivial tree from Jiri Kosina:
"Assorted tiny fixes queued in trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (22 commits)
DocBook: update EXPORT_SYMBOL entry to point at export.h
Documentation: update top level 00-INDEX file with new additions
ARM: at91/ide: remove unsused at91-ide Kconfig entry
percpu_counter.h: comment code for better readability
x86, efi: fix comment typo in head_32.S
IB: cxgb3: delay freeing mem untill entirely done with it
net: mvneta: remove unneeded version.h include
time: x86: report_lost_ticks doesn't exist any more
pcmcia: avoid static analysis complaint about use-after-free
fs/jfs: Fix typo in comment : 'how may' -> 'how many'
of: add missing documentation for of_platform_populate()
btrfs: remove unnecessary cur_trans set before goto loop in join_transaction
sound: soc: Fix typo in sound/codecs
treewide: Fix typo in various drivers
btrfs: fix comment typos
Update ibmvscsi module name in Kconfig.
powerpc: fix typo (utilties -> utilities)
of: fix spelling mistake in comment
h8300: Fix home page URL in h8300/README
xtensa: Fix home page URL in Kconfig
...
Merge misc patches from Andrew Morton:
- Florian has vanished so I appear to have become fbdev maintainer
again :(
- Joel and Mark are distracted to welcome to the new OCFS2 maintainer
- The backlight queue
- Small core kernel changes
- lib/ updates
- The rtc queue
- Various random bits
* akpm: (164 commits)
rtc: rtc-davinci: use devm_*() functions
rtc: rtc-max8997: use devm_request_threaded_irq()
rtc: rtc-max8907: use devm_request_threaded_irq()
rtc: rtc-da9052: use devm_request_threaded_irq()
rtc: rtc-wm831x: use devm_request_threaded_irq()
rtc: rtc-tps80031: use devm_request_threaded_irq()
rtc: rtc-lp8788: use devm_request_threaded_irq()
rtc: rtc-coh901331: use devm_clk_get()
rtc: rtc-vt8500: use devm_*() functions
rtc: rtc-tps6586x: use devm_request_threaded_irq()
rtc: rtc-imxdi: use devm_clk_get()
rtc: rtc-cmos: use dev_warn()/dev_dbg() instead of printk()/pr_debug()
rtc: rtc-pcf8583: use dev_warn() instead of printk()
rtc: rtc-sun4v: use pr_warn() instead of printk()
rtc: rtc-vr41xx: use dev_info() instead of printk()
rtc: rtc-rs5c313: use pr_err() instead of printk()
rtc: rtc-at91rm9200: use dev_dbg()/dev_err() instead of printk()/pr_debug()
rtc: rtc-rs5c372: use dev_dbg()/dev_warn() instead of printk()/pr_debug()
rtc: rtc-ds2404: use dev_err() instead of printk()
rtc: rtc-efi: use dev_err()/dev_warn()/pr_err() instead of printk()
...
LP8557 is one of LP855x family device, but it has different register map
and initialization process. To support this device, device specific
configuration is done through the lp855x_device_config structure.
Few register definitions are fixed for better readability.
BRIGHTNESS_CTRL -> LP855X_BRIGHTNESS_CTRL
DEVICE_CTRL -> LP855X_DEVICE_CTRL
EEPROM_START -> LP855X_EEPROM_START
EEPROM_END -> LP855X_EEPROM_END
EPROM_START -> LP8556_EPROM_START
EPROM_END -> LP8556_EPROM_END
And LP8557 register definitions are added. New register function,
lp855x_update_bit() is added.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After I came across a help text for SUNGEM mentioning a broken sun.com
URL, I felt like fixing those up, as they are now pointing to oracle.com
URLs.
Signed-off-by: Christian Kujau <lists@nerdbynature.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I'm testing swapout workload in a two-socket Xeon machine. The workload
has 10 threads, each thread sequentially accesses separate memory
region. TLB flush overhead is very big in the workload. For each page,
page reclaim need move it from active lru list and then unmap it. Both
need a TLB flush. And this is a multthread workload, TLB flush happens
in 10 CPUs. In X86, TLB flush uses generic smp_call)function. So this
workload stress smp_call_function_many heavily.
Without patch, perf shows:
+ 24.49% [k] generic_smp_call_function_interrupt
- 21.72% [k] _raw_spin_lock
- _raw_spin_lock
+ 79.80% __page_check_address
+ 6.42% generic_smp_call_function_interrupt
+ 3.31% get_swap_page
+ 2.37% free_pcppages_bulk
+ 1.75% handle_pte_fault
+ 1.54% put_super
+ 1.41% grab_super_passive
+ 1.36% __swap_duplicate
+ 0.68% blk_flush_plug_list
+ 0.62% swap_info_get
+ 6.55% [k] flush_tlb_func
+ 6.46% [k] smp_call_function_many
+ 5.09% [k] call_function_interrupt
+ 4.75% [k] default_send_IPI_mask_sequence_phys
+ 2.18% [k] find_next_bit
swapout throughput is around 1300M/s.
With the patch, perf shows:
- 27.23% [k] _raw_spin_lock
- _raw_spin_lock
+ 80.53% __page_check_address
+ 8.39% generic_smp_call_function_single_interrupt
+ 2.44% get_swap_page
+ 1.76% free_pcppages_bulk
+ 1.40% handle_pte_fault
+ 1.15% __swap_duplicate
+ 1.05% put_super
+ 0.98% grab_super_passive
+ 0.86% blk_flush_plug_list
+ 0.57% swap_info_get
+ 8.25% [k] default_send_IPI_mask_sequence_phys
+ 7.55% [k] call_function_interrupt
+ 7.47% [k] smp_call_function_many
+ 7.25% [k] flush_tlb_func
+ 3.81% [k] _raw_spin_lock_irqsave
+ 3.78% [k] generic_smp_call_function_single_interrupt
swapout throughput is around 1400M/s. So there is around a 7%
improvement, and total cpu utilization doesn't change.
Without the patch, cfd_data is shared by all CPUs.
generic_smp_call_function_interrupt does read/write cfd_data several times
which will create a lot of cache ping-pong. With the patch, the data
becomes per-cpu. The ping-pong is avoided. And from the perf data, this
doesn't make call_single_queue lock contend.
Next step is to remove generic_smp_call_function_interrupt() from arch
code.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This provides a band-aid to provide stable page writes on jbd without
needing to backport the fixed locking and page writeback bit handling
schemes of jbd2. The band-aid works by using bounce buffers to snapshot
page contents instead of waiting.
For those wondering about the ext3 bandage -- fixing the jbd locking
(which was done as part of ext4dev years ago) is a lot of surgery, and
setting PG_writeback on data pages when we actually hold the page lock
dropped ext3 performance by nearly an order of magnitude. If we're
going to migrate iscsi and raid to use stable page writes, the
complaints about high latency will likely return. We might as well
centralize their page snapshotting thing to one place.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Tested-by: Andy Lutomirski <luto@amacapital.net>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Create a helper function to check if a backing device requires stable
page writes and, if so, performs the necessary wait. Then, make it so
that all points in the memory manager that handle making pages writable
use the helper function. This should provide stable page write support
to most filesystems, while eliminating unnecessary waiting for devices
that don't require the feature.
Before this patchset, all filesystems would block, regardless of whether
or not it was necessary. ext3 would wait, but still generate occasional
checksum errors. The network filesystems were left to do their own
thing, so they'd wait too.
After this patchset, all the disk filesystems except ext3 and btrfs will
wait only if the hardware requires it. ext3 (if necessary) snapshots
pages instead of blocking, and btrfs provides its own bdi so the mm will
never wait. Network filesystems haven't been touched, so either they
provide their own stable page guarantees or they don't block at all.
The blocking behavior is back to what it was before 3.0 if you don't
have a disk requiring stable page writes.
Here's the result of using dbench to test latency on ext2:
3.8.0-rc3:
Operation Count AvgLat MaxLat
----------------------------------------
WriteX 109347 0.028 59.817
ReadX 347180 0.004 3.391
Flush 15514 29.828 287.283
Throughput 57.429 MB/sec 4 clients 4 procs max_latency=287.290 ms
3.8.0-rc3 + patches:
WriteX 105556 0.029 4.273
ReadX 335004 0.005 4.112
Flush 14982 30.540 298.634
Throughput 55.4496 MB/sec 4 clients 4 procs max_latency=298.650 ms
As you can see, the maximum write latency drops considerably with this
patch enabled. The other filesystems (ext3/ext4/xfs/btrfs) behave
similarly, but see the cover letter for those results.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
