Some debug code wasn't properly removed from the initial 64k pages
patch, and while it's harmless, it's also slowing down significantly a
very hot code path, thus it should really be removed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The previous commit will use the page-at-a-time hypervisor call for
setting up IOMMU entries when we are using 64k pages and setting up
one 64k page, even though that means 16 calls to the hypervisor, since
the hypervisor still works on 4k pages. This optimizes this case by
using the multi-page IOMMU setup hypervisor call instead.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Must adjust tcenum and npages by TCE_PAGE_FACTOR to convert between
64KB pages and TCE (4K) pages. (This is done in other places, except
for this one location.)
Signed-off-by: Michal Ostrowski <mostrows at watson ibm com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Email address update, changing old work address to personal (permanent)
one.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We were using udelay in the loop on the primary cpu waiting for the
secondary cpu to take the timebase value. Unfortunately now that
udelay uses the timebase, and the timebase is stopped at this point,
the udelay never terminated. This fixes it by not using udelay, and
increases the number of loops before we time out to compensate.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes 32-bit CHRP systems use the RTAS time-of-day routines if
available. It fixes a bug in the RTAS time-of-day routines where they
were storing a 64-bit timebase value in an unsigned long by making
those variables u64. Also, the direct-access time-of-day routines
had the wrong convention for the month and year in the struct rtc_time.
Signed-off-by: Paul Mackerras <paulus@samba.org>
pseries_dedicated_idle() was using __get_tb which used to be defined
in asm/delay.h. Change it to use get_tb from asm/time.h, which is
in fact exactly the same thing.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Reserve the Maple RTC I/O resource. Needed now we use genrtc.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the kernel supports both G5 and pSeries, and CONFIG_EEH is enabled,
eeh_init() is (quite reasonably) never called when we boot on a G5. Yet
eeh_check_failure() still gets called. We should avoid doing that if
!eeh_subsystem_enabled.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Hi,
The previous PowerBook patch didn't contain the feature table updates
for ARCH=powerpc. Here they are.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I discovered that in some cases (PowerMac for example) we wouldn't
properly map the PCI IO space on recent kernels. In addition, the code
for initializing PCI host bridges was scattered all over the place with
some duplication between platforms.
This patch fixes the problem and does a small cleanup by creating a
pcibios_alloc_controller() in pci_64.c that is similar to the one in
pci_32.c (just takes an additional device node argument) that takes care
of all the grunt allocation and initialisation work. It should work for
both boot time and dynamically allocated PHBs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Also deletes files in arch/ppc64 that are no longer used now that
we don't compile with ARCH=ppc64 any more.
Signed-off-by: Paul Mackerras <paulus@samba.org>
log_plpar_hcall_return is only used on PPC_PSERIES, so move
it closer to its users and inside ifdef CONFIG_PPC_PSERIES.
remove the last vestiges of systemcfg in iSeries.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
This moves the rtas RTC callbacks to rtas-rtc.c in arch/powerpc/kernel,
and kills the rest of arch/ppc64/kernel/rtc.c which was just a duplicate
of the genrtc functionality. Also enable build of genrtc for
CONFIG_PPC64 (it just works are we already have the required callbacks)
and enable it in all defconfigs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes various errors in the new functions added in the vDSO's,
I've now verified all functions on both 32 and 64 bits vDSOs. It also
fix a sign extension bug getting the initial time of day at boot that
could cause the monotonic clock value to be completely on bogus for
64 bits applications (with either the vDSO or the syscall) on
powermacs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We currently have a ppc_md member called cpu_irq_down, which disables IRQs
for the cpu in question. The only caller of cpu_irq_down is the kexec code.
On pSeries we need to do more than just teardown IRQs at kexec time, so rename
the ppc_md member to kexec_cpu_down and expand it. The pSeries code needs to
know, and other platforms might too, whether we're doing a crash shutdown (ie.
panicking) or a regular kexec, so add a flag for that.
The pSeries implementation of kexec_cpu_down does an unregister VPA call, which
tells the Hypervisor to stop writing stuff into our pacas. Without this we can
get weird memory corruption bugs when we kexec, caused by the Hypervisor
writing into the first kernel's pacas which happens to be somewhere interesting
in the second kernel's memory.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We needed the VDSO symbols in the arch/ppc asm-offsets.c, and there
were a few usages of _systemcfg still left lying around.
Signed-off-by: Paul Mackerras <paulus@samba.org>
We have been printing the raw ppc64_firmware_features during boot. Since
we can work it out from the device tree, lets remove it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
17-eeh-slot-marking-bug.patch
A device that experiences a PCI outage may be just one deivce out
of many that was affected. In order to avoid repeated reports of
a failure, the entire tree of affected devices should be marked
as failed. This patch marks up the entire tree.
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This also make klimit have the same type on 32-bit as on 64-bit,
namely unsigned long, and defines and initializes it in one place.
Signed-off-by: Paul Mackerras <paulus@samba.org>
phbs_remap_io(), which maps the PCI IO space into the kernel virtual space,
is called too early on powermac, and thus doesn't work.
This fixes it by removing the call from all platforms and putting it back
into the ppc64 common code where it belongs, after the actual probing of
the bus.
That means that before that call, only the ISA IO space (if any) is mapped,
any PIO access (from quirks for example) will fail. This happens not to be
a problem for now, but we'll have to rework that code if it becomes one in
the future.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges platform codes. systemcfg->platform is no longer used,
systemcfg use in general is deprecated as much as possible (and renamed
_systemcfg before it gets completely moved elsewhere in a future patch),
_machine is now used on ppc64 along as ppc32. Platform codes aren't gone
yet but we are getting a step closer. A bunch of asm code in head[_64].S
is also turned into C code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch consolidates macros used to generate assembly for
compatibility across different CPUs or configs. A new header,
asm-powerpc/asm-compat.h contains the main compatibility macros. It
uses some preprocessor magic to make the macros suitable both for use
in .S files, and in inline asm in .c files. Headers (bitops.h,
uaccess.h, atomic.h, bug.h) which had their own such compatibility
macros are changed to use asm-compat.h.
ppc_asm.h is now for use in .S files *only*, and a #error enforces
that. As such, we're a lot more careless about namespace pollution
here than in asm-compat.h.
While we're at it, this patch adds a call to the PPC405_ERR77 macro in
futex.h which should have had it already, but didn't.
Built and booted on pSeries, Maple and iSeries (ARCH=powerpc). Built
for 32-bit powermac (ARCH=powerpc) and Walnut (ARCH=ppc).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
scanlog.c is only compiled on pSeries. Thus, this patch moves it to
platforms/pseries.
Built and booted on pSeries LPAR (ARCH=powerpc and ARCH=ppc64). Built
for iSeries (ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds code to work around some problems with old versions of
Open Firmware, such as on the early powermacs (7500 etc.) and the
"Longtrail" CHRP machine. On these machines we have to claim
the physical and virtual address ranges explicitly when claiming
memory and then set up a V->P mapping.
The Longtrail has more problems: setprop doesn't work, and we have
to set an "allow-reclaim" variable to 0 in order to get claim on
physical memory ranges to fail if the memory is already claimed.
Signed-off-by: Paul Mackerras <paulus@samba.org>
14-eeh-device-bar-save.patch
After a PCI device has been resest, the device BAR's and other config
space info must be restored to the same state as they were in when
the firmware first handed us this device. This will allow the
PCI device driver, when restarted, to correctly recognize and set up
the device.
Tis patch saves the device config space as early as reasonable after
the firmware has handed over the device. Te state resore funcion
is inteded for use by the EEH recovery routines.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
13-eeh-recovery-support-routines.patch
EEH Recovery support routines
This patch adds routines required to help drive the recovery of
EEH-frozen slots. The main function is to drive the PCI #RST
signal line high for a qurter of a second, and then allow for
a second & a half of settle time.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
12-eeh-event-dispatcher.patch
ppc64: EEH Recovery dispatcher thread
This patch adds a mechanism to create recovery threads when an
EEH event is received. Since an EEH freeze state may be detected
within an interrupt context, we need to get out of the interrupt
context before starting recovery. This dispatcher does this in
two steps: first, it uses a workqueue to get out, and then
lanuches a kernel thread, so that the recovery routine can
sleep for exteded periods without upseting the keventd.
A kernel thread is created with each EEH event, rather than
having one long-running daemon started at boot time. This is
because it is anticipated that EEH events will be very rare
(very very rare, ideally) and so its pointless to cluter the
process tables with a daemon that will almost never run.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
11-eeh-move-to-powerpc.patch
Move arch/ppc64/kernel/eeh.c to arch//powerpc/platforms/pseries/eeh.c
No other changes (except for Makefile to build it)
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make some changes to the NEED_RESCHED and POLLING_NRFLAG to reduce
confusion, and make their semantics rigid. Improves efficiency of
resched_task and some cpu_idle routines.
* In resched_task:
- TIF_NEED_RESCHED is only cleared with the task's runqueue lock held,
and as we hold it during resched_task, then there is no need for an
atomic test and set there. The only other time this should be set is
when the task's quantum expires, in the timer interrupt - this is
protected against because the rq lock is irq-safe.
- If TIF_NEED_RESCHED is set, then we don't need to do anything. It
won't get unset until the task get's schedule()d off.
- If we are running on the same CPU as the task we resched, then set
TIF_NEED_RESCHED and no further action is required.
- If we are running on another CPU, and TIF_POLLING_NRFLAG is *not* set
after TIF_NEED_RESCHED has been set, then we need to send an IPI.
Using these rules, we are able to remove the test and set operation in
resched_task, and make clear the previously vague semantics of
POLLING_NRFLAG.
* In idle routines:
- Enter cpu_idle with preempt disabled. When the need_resched() condition
becomes true, explicitly call schedule(). This makes things a bit clearer
(IMO), but haven't updated all architectures yet.
- Many do a test and clear of TIF_NEED_RESCHED for some reason. According
to the resched_task rules, this isn't needed (and actually breaks the
assumption that TIF_NEED_RESCHED is only cleared with the runqueue lock
held). So remove that. Generally one less locked memory op when switching
to the idle thread.
- Many idle routines clear TIF_POLLING_NRFLAG, and only set it in the inner
most polling idle loops. The above resched_task semantics allow it to be
set until before the last time need_resched() is checked before going into
a halt requiring interrupt wakeup.
Many idle routines simply never enter such a halt, and so POLLING_NRFLAG
can be always left set, completely eliminating resched IPIs when rescheduling
the idle task.
POLLING_NRFLAG width can be increased, to reduce the chance of resched IPIs.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Con Kolivas <kernel@kolivas.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Run idle threads with preempt disabled.
Also corrected a bugs in arm26's cpu_idle (make it actually call schedule()).
How did it ever work before?
Might fix the CPU hotplugging hang which Nigel Cunningham noted.
We think the bug hits if the idle thread is preempted after checking
need_resched() and before going to sleep, then the CPU offlined.
After calling stop_machine_run, the CPU eventually returns from preemption and
into the idle thread and goes to sleep. The CPU will continue executing
previous idle and have no chance to call play_dead.
By disabling preemption until we are ready to explicitly schedule, this bug is
fixed and the idle threads generally become more robust.
From: alexs <ashepard@u.washington.edu>
PPC build fix
From: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
MIPS build fix
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use __do_IRQ instead. The only difference is that every controller
is now assumed to have an end() routine (only xics_8259 did not).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
CPU freq support using 970FX powertune facility for iMac G5 and SMU
based single CPU desktop.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the arch/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in arch/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define ppc_md.set_dabr for both 32 + 64 bit. Cleanup the implementation for
pSeries also, it was needlessly complex. Now we just do two firmware tests at
setup time, and use one of two functions, rather than using one function and
testing on every call.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
