Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
- Move the arch-specific code into arch/arm64/kvm
- Start the post-32bit cleanup
- Cherry-pick a few non-invasive pre-NV patches
x86:
- Rework of TLB flushing
- Rework of event injection, especially with respect to nested virtualization
- Nested AMD event injection facelift, building on the rework of generic code
and fixing a lot of corner cases
- Nested AMD live migration support
- Optimization for TSC deadline MSR writes and IPIs
- Various cleanups
- Asynchronous page fault cleanups (from tglx, common topic branch with tip tree)
- Interrupt-based delivery of asynchronous "page ready" events (host side)
- Hyper-V MSRs and hypercalls for guest debugging
- VMX preemption timer fixes
s390:
- Cleanups
Generic:
- switch vCPU thread wakeup from swait to rcuwait
The other architectures, and the guest side of the asynchronous page fault
work, will come next week.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl7VJcYUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroPf6QgAq4wU5wdd1lTGz/i3DIhNVJNJgJlp
ozLzRdMaJbdbn5RpAK6PEBd9+pt3+UlojpFB3gpJh2Nazv2OzV4yLQgXXXyyMEx1
5Hg7b4UCJYDrbkCiegNRv7f/4FWDkQ9dx++RZITIbxeskBBCEI+I7GnmZhGWzuC4
7kj4ytuKAySF2OEJu0VQF6u0CvrNYfYbQIRKBXjtOwuRK4Q6L63FGMJpYo159MBQ
asg3B1jB5TcuGZ9zrjL5LkuzaP4qZZHIRs+4kZsH9I6MODHGUxKonrkablfKxyKy
CFK+iaHCuEXXty5K0VmWM3nrTfvpEjVjbMc7e1QGBQ5oXsDM0pqn84syRg==
=v7Wn
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"ARM:
- Move the arch-specific code into arch/arm64/kvm
- Start the post-32bit cleanup
- Cherry-pick a few non-invasive pre-NV patches
x86:
- Rework of TLB flushing
- Rework of event injection, especially with respect to nested
virtualization
- Nested AMD event injection facelift, building on the rework of
generic code and fixing a lot of corner cases
- Nested AMD live migration support
- Optimization for TSC deadline MSR writes and IPIs
- Various cleanups
- Asynchronous page fault cleanups (from tglx, common topic branch
with tip tree)
- Interrupt-based delivery of asynchronous "page ready" events (host
side)
- Hyper-V MSRs and hypercalls for guest debugging
- VMX preemption timer fixes
s390:
- Cleanups
Generic:
- switch vCPU thread wakeup from swait to rcuwait
The other architectures, and the guest side of the asynchronous page
fault work, will come next week"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (256 commits)
KVM: selftests: fix rdtsc() for vmx_tsc_adjust_test
KVM: check userspace_addr for all memslots
KVM: selftests: update hyperv_cpuid with SynDBG tests
x86/kvm/hyper-v: Add support for synthetic debugger via hypercalls
x86/kvm/hyper-v: enable hypercalls regardless of hypercall page
x86/kvm/hyper-v: Add support for synthetic debugger interface
x86/hyper-v: Add synthetic debugger definitions
KVM: selftests: VMX preemption timer migration test
KVM: nVMX: Fix VMX preemption timer migration
x86/kvm/hyper-v: Explicitly align hcall param for kvm_hyperv_exit
KVM: x86/pmu: Support full width counting
KVM: x86/pmu: Tweak kvm_pmu_get_msr to pass 'struct msr_data' in
KVM: x86: announce KVM_FEATURE_ASYNC_PF_INT
KVM: x86: acknowledgment mechanism for async pf page ready notifications
KVM: x86: interrupt based APF 'page ready' event delivery
KVM: introduce kvm_read_guest_offset_cached()
KVM: rename kvm_arch_can_inject_async_page_present() to kvm_arch_can_dequeue_async_page_present()
KVM: x86: extend struct kvm_vcpu_pv_apf_data with token info
Revert "KVM: async_pf: Fix #DF due to inject "Page not Present" and "Page Ready" exceptions simultaneously"
KVM: VMX: Replace zero-length array with flexible-array
...
Pull uaccess/csum updates from Al Viro:
"Regularize the sitation with uaccess checksum primitives:
- fold csum_partial_... into csum_and_copy_..._user()
- on x86 collapse several access_ok()/stac()/clac() into
user_access_begin()/user_access_end()"
* 'uaccess.csum' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
default csum_and_copy_to_user(): don't bother with access_ok()
take the dummy csum_and_copy_from_user() into net/checksum.h
arm: switch to csum_and_copy_from_user()
sh32: convert to csum_and_copy_from_user()
m68k: convert to csum_and_copy_from_user()
xtensa: switch to providing csum_and_copy_from_user()
sparc: switch to providing csum_and_copy_from_user()
parisc: turn csum_partial_copy_from_user() into csum_and_copy_from_user()
alpha: turn csum_partial_copy_from_user() into csum_and_copy_from_user()
ia64: turn csum_partial_copy_from_user() into csum_and_copy_from_user()
ia64: csum_partial_copy_nocheck(): don't abuse csum_partial_copy_from_user()
x86: switch 32bit csum_and_copy_to_user() to user_access_{begin,end}()
x86: switch both 32bit and 64bit to providing csum_and_copy_from_user()
x86_64: csum_..._copy_..._user(): switch to unsafe_..._user()
get rid of csum_partial_copy_to_user()
If two page ready notifications happen back to back the second one is not
delivered and the only mechanism we currently have is
kvm_check_async_pf_completion() check in vcpu_run() loop. The check will
only be performed with the next vmexit when it happens and in some cases
it may take a while. With interrupt based page ready notification delivery
the situation is even worse: unlike exceptions, interrupts are not handled
immediately so we must check if the slot is empty. This is slow and
unnecessary. Introduce dedicated MSR_KVM_ASYNC_PF_ACK MSR to communicate
the fact that the slot is free and host should check its notification
queue. Mandate using it for interrupt based 'page ready' APF event
delivery.
As kvm_check_async_pf_completion() is going away from vcpu_run() we need
a way to communicate the fact that vcpu->async_pf.done queue has
transitioned from empty to non-empty state. Introduce
kvm_arch_async_page_present_queued() and KVM_REQ_APF_READY to do the job.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200525144125.143875-7-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
An innocent reader of the following x86 KVM code:
bool kvm_arch_can_inject_async_page_present(struct kvm_vcpu *vcpu)
{
if (!(vcpu->arch.apf.msr_val & KVM_ASYNC_PF_ENABLED))
return true;
...
may get very confused: if APF mechanism is not enabled, why do we report
that we 'can inject async page present'? In reality, upon injection
kvm_arch_async_page_present() will check the same condition again and,
in case APF is disabled, will just drop the item. This is fine as the
guest which deliberately disabled APF doesn't expect to get any APF
notifications.
Rename kvm_arch_can_inject_async_page_present() to
kvm_arch_can_dequeue_async_page_present() to make it clear what we are
checking: if the item can be dequeued (meaning either injected or just
dropped).
On s390 kvm_arch_can_inject_async_page_present() always returns 'true' so
the rename doesn't matter much.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200525144125.143875-4-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
now that can be done conveniently - all non-trivial cases have
_HAVE_ARCH_COPY_AND_CSUM_FROM_USER defined, so the fallback in
net/checksum.h is used only for dummy (copy_from_user, then
csum_partial) implementation. Allowing us to get rid of all
dummy instances, both of csum_and_copy_from_user() and
csum_partial_copy_from_user().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 5e1fb45ec8 ("s390/ccwgroup: remove pm support") removed power
management support from the ccwgroup bus driver. So remove the
associated callbacks from all ccwgroup drivers.
CC: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two new stats for exposing halt-polling cpu usage:
halt_poll_success_ns
halt_poll_fail_ns
Thus sum of these 2 stats is the total cpu time spent polling. "success"
means the VCPU polled until a virtual interrupt was delivered. "fail"
means the VCPU had to schedule out (either because the maximum poll time
was reached or it needed to yield the CPU).
To avoid touching every arch's kvm_vcpu_stat struct, only update and
export halt-polling cpu usage stats if we're on x86.
Exporting cpu usage as a u64 and in nanoseconds means we will overflow at
~500 years, which seems reasonably large.
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: Jon Cargille <jcargill@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <20200508182240.68440-1-jcargill@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The s390_mmio_read/write syscalls are currently broken when running with
MIO.
The new pcistb_mio/pcstg_mio/pcilg_mio instructions are executed
similiarly to normal load/store instructions and do address translation
in the current address space. That means inside the kernel they are
aware of mappings into kernel address space while outside the kernel
they use user space mappings (usually created through mmap'ing a PCI
device file).
Now when existing user space applications use the s390_pci_mmio_write
and s390_pci_mmio_read syscalls, they pass I/O addresses that are mapped
into user space so as to be usable with the new instructions without
needing a syscall. Accessing these addresses with the old instructions
as done currently leads to a kernel panic.
Also, for such a user space mapping there may not exist an equivalent
kernel space mapping which means we can't just use the new instructions
in kernel space.
Instead of replicating user mappings in the kernel which then might
collide with other mappings, we can conceptually execute the new
instructions as if executed by the user space application using the
secondary address space. This even allows us to directly store to the
user pointer without the need for copy_to/from_user().
Cc: stable@vger.kernel.org
Fixes: 71ba41c9b1 ("s390/pci: provide support for MIO instructions")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Merge yet more updates from Andrew Morton:
- Almost all of the rest of MM (memcg, slab-generic, slab, pagealloc,
gup, hugetlb, pagemap, memremap)
- Various other things (hfs, ocfs2, kmod, misc, seqfile)
* akpm: (34 commits)
ipc/util.c: sysvipc_find_ipc() should increase position index
kernel/gcov/fs.c: gcov_seq_next() should increase position index
fs/seq_file.c: seq_read(): add info message about buggy .next functions
drivers/dma/tegra20-apb-dma.c: fix platform_get_irq.cocci warnings
change email address for Pali Rohár
selftests: kmod: test disabling module autoloading
selftests: kmod: fix handling test numbers above 9
docs: admin-guide: document the kernel.modprobe sysctl
fs/filesystems.c: downgrade user-reachable WARN_ONCE() to pr_warn_once()
kmod: make request_module() return an error when autoloading is disabled
mm/memremap: set caching mode for PCI P2PDMA memory to WC
mm/memory_hotplug: add pgprot_t to mhp_params
powerpc/mm: thread pgprot_t through create_section_mapping()
x86/mm: introduce __set_memory_prot()
x86/mm: thread pgprot_t through init_memory_mapping()
mm/memory_hotplug: rename mhp_restrictions to mhp_params
mm/memory_hotplug: drop the flags field from struct mhp_restrictions
mm/special: create generic fallbacks for pte_special() and pte_mkspecial()
mm/vma: introduce VM_ACCESS_FLAGS
mm/vma: define a default value for VM_DATA_DEFAULT_FLAGS
...
There are many platforms with exact same value for VM_DATA_DEFAULT_FLAGS
This creates a default value for VM_DATA_DEFAULT_FLAGS in line with the
existing VM_STACK_DEFAULT_FLAGS. While here, also define some more
macros with standard VMA access flag combinations that are used
frequently across many platforms. Apart from simplification, this
reduces code duplication as well.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Guo Ren <guoren@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Chris Zankel <chris@zankel.net>
Link: http://lkml.kernel.org/r/1583391014-8170-2-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Upper-layer drivers allocate their SBALs by calling qdio_alloc_buffers()
for each individual queue. But when later passing the SBAL addresses to
qdio_establish(), they need to be in a single array of pointers.
So if the driver uses multiple Input or Output queues, it needs to
allocate a temporary array just to present all its SBAL pointers in this
layout.
This patch slightly changes the format of the QDIO initialization data,
so that drivers can pass a per-queue array where each element points to
a queue's SBAL array.
zfcp doesn't use multiple queues, so the impact there is trivial.
For qeth this brings a nice reduction in complexity, and removes
a page-sized allocation.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
All that qdio_allocate() actually uses from the init_data is the cdev,
and the number of Input and Output Queues. Have the driver pass those as
parameters, and defer the init_data processing into qdio_establish().
This includes writing per-device(!) trace entries, and most of the
sanity checks.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
- Update maintainers. Niklas Schnelle takes over zpci and Vineeth Vijayan
common io code.
- Extend cpuinfo to include topology information.
- Add new extended counters for IBM z15 and sampling buffer allocation
rework in perf code.
- Add control over zeroing out memory during system restart.
- CCA protected key block version 2 support and other fixes/improvements
in crypto code.
- Convert to new fallthrough; annotations.
- Replace zero-length arrays with flexible-arrays.
- QDIO debugfs and other small improvements.
- Drop 2-level paging support optimization for compat tasks. Varios
mm cleanups.
- Remove broken and unused hibernate / power management support.
- Remove fake numa support which does not bring any benefits.
- Exclude offline CPUs from CPU topology masks to be more consistent
with other architectures.
- Prevent last branching instruction address leaking to userspace.
- Other small various fixes and improvements all over the code.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAl6Ig2YACgkQjYWKoQLX
FBj2gggAibnHOl9d0ngX1mVT4nz51R3V8z5sEQjNMr2uHBmaTqs7pi/00gaFMxoC
NngVEXvL443jSogQivthGgXPpRCV9xdKE3sp38j7fF4LgHoeuDtGd1oaX4W9Rqk0
7Yii35EaO2e2WHdOKaAbu+ZvDRunFjERyntc51MYaIUivFosogSo07vC73vFIArF
VGStS09fJ4Ny76ott896T7Ulx1Iek/MkF1vponEMLGNUIcLIQbbxZxOwgz0pHuEF
SlyyJBnhOIaAJGOYlKREQDt1cew+hsxluPU+a01bwdsmdZv9LH1BGwLayDqTH58i
QWvtEpzJFmDvo9jGM1v81ebaGnyCKg==
=hiGF
-----END PGP SIGNATURE-----
Merge tag 's390-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Update maintainers. Niklas Schnelle takes over zpci and Vineeth
Vijayan common io code.
- Extend cpuinfo to include topology information.
- Add new extended counters for IBM z15 and sampling buffer allocation
rework in perf code.
- Add control over zeroing out memory during system restart.
- CCA protected key block version 2 support and other
fixes/improvements in crypto code.
- Convert to new fallthrough; annotations.
- Replace zero-length arrays with flexible-arrays.
- QDIO debugfs and other small improvements.
- Drop 2-level paging support optimization for compat tasks. Varios mm
cleanups.
- Remove broken and unused hibernate / power management support.
- Remove fake numa support which does not bring any benefits.
- Exclude offline CPUs from CPU topology masks to be more consistent
with other architectures.
- Prevent last branching instruction address leaking to userspace.
- Other small various fixes and improvements all over the code.
* tag 's390-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (57 commits)
s390/mm: cleanup init_new_context() callback
s390/mm: cleanup virtual memory constants usage
s390/mm: remove page table downgrade support
s390/qdio: set qdio_irq->cdev at allocation time
s390/qdio: remove unused function declarations
s390/ccwgroup: remove pm support
s390/ap: remove power management code from ap bus and drivers
s390/zcrypt: use kvmalloc instead of kmalloc for 256k alloc
s390/mm: cleanup arch_get_unmapped_area() and friends
s390/ism: remove pm support
s390/cio: use fallthrough;
s390/vfio: use fallthrough;
s390/zcrypt: use fallthrough;
s390: use fallthrough;
s390/cpum_sf: Fix wrong page count in error message
s390/diag: fix display of diagnose call statistics
s390/ap: Remove ap device suspend and resume callbacks
s390/pci: Improve handling of unset UID
s390/pci: Fix zpci_alloc_domain() over allocation
s390/qdio: pass ISC as parameter to chsc_sadc()
...
* GICv4.1 support
* 32bit host removal
PPC:
* secure (encrypted) using under the Protected Execution Framework
ultravisor
s390:
* allow disabling GISA (hardware interrupt injection) and protected
VMs/ultravisor support.
x86:
* New dirty bitmap flag that sets all bits in the bitmap when dirty
page logging is enabled; this is faster because it doesn't require bulk
modification of the page tables.
* Initial work on making nested SVM event injection more similar to VMX,
and less buggy.
* Various cleanups to MMU code (though the big ones and related
optimizations were delayed to 5.8). Instead of using cr3 in function
names which occasionally means eptp, KVM too has standardized on "pgd".
* A large refactoring of CPUID features, which now use an array that
parallels the core x86_features.
* Some removal of pointer chasing from kvm_x86_ops, which will also be
switched to static calls as soon as they are available.
* New Tigerlake CPUID features.
* More bugfixes, optimizations and cleanups.
Generic:
* selftests: cleanups, new MMU notifier stress test, steal-time test
* CSV output for kvm_stat.
KVM/MIPS has been broken since 5.5, it does not compile due to a patch committed
by MIPS maintainers. I had already prepared a fix, but the MIPS maintainers
prefer to fix it in generic code rather than KVM so they are taking care of it.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl6GOnIUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMfxwf/ZKLZiRoaovXCOG71M/eHtQb8ZIqU
3MPy+On3eC5Sk/aBxWUL9EFZsbYG6kYdbZ1VOvG9XPBoLlnkDSm/IR0kaELHtnjj
oGVda/tvGn46Ne39y8xBptmb91WDcWH0vFthT/CwlMxAw3xjr+gG7Qyo+8F2CW6m
SSSuLiHSBnyO1cQKruBTHZ8qnR8LlnfXEqtd6Y4LFLic0LbLIoIdRcT3wjQrcZrm
Djd7wbTEYZjUfoqZ72ekwEDUsONcDLDSKcguDO9pSMSCGhpxCVT5Vy68KRpoIMs2
nzNWDKjvqQo5zb2+GWxJgkd12Hv+n7PCXZMbVrWBu1pQsewUns9m4mkpGw==
=6fGt
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"ARM:
- GICv4.1 support
- 32bit host removal
PPC:
- secure (encrypted) using under the Protected Execution Framework
ultravisor
s390:
- allow disabling GISA (hardware interrupt injection) and protected
VMs/ultravisor support.
x86:
- New dirty bitmap flag that sets all bits in the bitmap when dirty
page logging is enabled; this is faster because it doesn't require
bulk modification of the page tables.
- Initial work on making nested SVM event injection more similar to
VMX, and less buggy.
- Various cleanups to MMU code (though the big ones and related
optimizations were delayed to 5.8). Instead of using cr3 in
function names which occasionally means eptp, KVM too has
standardized on "pgd".
- A large refactoring of CPUID features, which now use an array that
parallels the core x86_features.
- Some removal of pointer chasing from kvm_x86_ops, which will also
be switched to static calls as soon as they are available.
- New Tigerlake CPUID features.
- More bugfixes, optimizations and cleanups.
Generic:
- selftests: cleanups, new MMU notifier stress test, steal-time test
- CSV output for kvm_stat"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (277 commits)
x86/kvm: fix a missing-prototypes "vmread_error"
KVM: x86: Fix BUILD_BUG() in __cpuid_entry_get_reg() w/ CONFIG_UBSAN=y
KVM: VMX: Add a trampoline to fix VMREAD error handling
KVM: SVM: Annotate svm_x86_ops as __initdata
KVM: VMX: Annotate vmx_x86_ops as __initdata
KVM: x86: Drop __exit from kvm_x86_ops' hardware_unsetup()
KVM: x86: Copy kvm_x86_ops by value to eliminate layer of indirection
KVM: x86: Set kvm_x86_ops only after ->hardware_setup() completes
KVM: VMX: Configure runtime hooks using vmx_x86_ops
KVM: VMX: Move hardware_setup() definition below vmx_x86_ops
KVM: x86: Move init-only kvm_x86_ops to separate struct
KVM: Pass kvm_init()'s opaque param to additional arch funcs
s390/gmap: return proper error code on ksm unsharing
KVM: selftests: Fix cosmetic copy-paste error in vm_mem_region_move()
KVM: Fix out of range accesses to memslots
KVM: X86: Micro-optimize IPI fastpath delay
KVM: X86: Delay read msr data iff writes ICR MSR
KVM: PPC: Book3S HV: Add a capability for enabling secure guests
KVM: arm64: GICv4.1: Expose HW-based SGIs in debugfs
KVM: arm64: GICv4.1: Allow non-trapping WFI when using HW SGIs
...
Change a header to mandatory-y if both of the following are met:
[1] At least one architecture (except um) specifies it as generic-y in
arch/*/include/asm/Kbuild
[2] Every architecture (except um) either has its own implementation
(arch/*/include/asm/*.h) or specifies it as generic-y in
arch/*/include/asm/Kbuild
This commit was generated by the following shell script.
----------------------------------->8-----------------------------------
arches=$(cd arch; ls -1 | sed -e '/Kconfig/d' -e '/um/d')
tmpfile=$(mktemp)
grep "^mandatory-y +=" include/asm-generic/Kbuild > $tmpfile
find arch -path 'arch/*/include/asm/Kbuild' |
xargs sed -n 's/^generic-y += \(.*\)/\1/p' | sort -u |
while read header
do
mandatory=yes
for arch in $arches
do
if ! grep -q "generic-y += $header" arch/$arch/include/asm/Kbuild &&
! [ -f arch/$arch/include/asm/$header ]; then
mandatory=no
break
fi
done
if [ "$mandatory" = yes ]; then
echo "mandatory-y += $header" >> $tmpfile
for arch in $arches
do
sed -i "/generic-y += $header/d" arch/$arch/include/asm/Kbuild
done
fi
done
sed -i '/^mandatory-y +=/d' include/asm-generic/Kbuild
LANG=C sort $tmpfile >> include/asm-generic/Kbuild
----------------------------------->8-----------------------------------
One obvious benefit is the diff stat:
25 files changed, 52 insertions(+), 557 deletions(-)
It is tedious to list generic-y for each arch that needs it.
So, mandatory-y works like a fallback default (by just wrapping
asm-generic one) when arch does not have a specific header
implementation.
See the following commits:
def3f7cefea1b39bae16
It is tedious to convert headers one by one, so I processed by a shell
script.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/20200210175452.5030-1-masahiroy@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
"Highlights:
1) Fix the iwlwifi regression, from Johannes Berg.
2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.
3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.
4) Add TTL decrement action to openvswitch, from Matteo Croce.
5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.
6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.
7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.
8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.
9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.
10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.
11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.
12) Support bcmgenet on ACPI, from Jeremy Linton.
13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.
14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.
15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.
16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.
17) Offload FIFO qdisc in mlxsw, from Petr Machata.
18) Support UDP sockets in sockmap, from Lorenz Bauer.
19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.
20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.
21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.
22) Add support for hw offload of MACSEC, from Antoine Tenart.
23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.
24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.
25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- Continued user-access cleanups in the futex code.
- percpu-rwsem rewrite that uses its own waitqueue and atomic_t
instead of an embedded rwsem. This addresses a couple of
weaknesses, but the primary motivation was complications on the -rt
kernel.
- Introduce raw lock nesting detection on lockdep
(CONFIG_PROVE_RAW_LOCK_NESTING=y), document the raw_lock vs. normal
lock differences. This too originates from -rt.
- Reuse lockdep zapped chain_hlocks entries, to conserve RAM
footprint on distro-ish kernels running into the "BUG:
MAX_LOCKDEP_CHAIN_HLOCKS too low!" depletion of the lockdep
chain-entries pool.
- Misc cleanups, smaller fixes and enhancements - see the changelog
for details"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (55 commits)
fs/buffer: Make BH_Uptodate_Lock bit_spin_lock a regular spinlock_t
thermal/x86_pkg_temp: Make pkg_temp_lock a raw_spinlock_t
Documentation/locking/locktypes: Minor copy editor fixes
Documentation/locking/locktypes: Further clarifications and wordsmithing
m68knommu: Remove mm.h include from uaccess_no.h
x86: get rid of user_atomic_cmpxchg_inatomic()
generic arch_futex_atomic_op_inuser() doesn't need access_ok()
x86: don't reload after cmpxchg in unsafe_atomic_op2() loop
x86: convert arch_futex_atomic_op_inuser() to user_access_begin/user_access_end()
objtool: whitelist __sanitizer_cov_trace_switch()
[parisc, s390, sparc64] no need for access_ok() in futex handling
sh: no need of access_ok() in arch_futex_atomic_op_inuser()
futex: arch_futex_atomic_op_inuser() calling conventions change
completion: Use lockdep_assert_RT_in_threaded_ctx() in complete_all()
lockdep: Add posixtimer context tracing bits
lockdep: Annotate irq_work
lockdep: Add hrtimer context tracing bits
lockdep: Introduce wait-type checks
completion: Use simple wait queues
sched/swait: Prepare usage in completions
...
The set of values asce_limit may be assigned with is TASK_SIZE_MAX,
_REGION1_SIZE, _REGION2_SIZE and 0 as a special case if the callback
was called from execve().
Do VM_BUG_ON() if asce_limit is something else.
Save few CPU cycles by removing unnecessary asce_limit re-assignment
in case of 3-level task and redundant PGD entry type reconstruction.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
This update consolidates page table handling code. Because
there are hardly any 31-bit binaries left we do not need to
optimize for that.
No extra efforts are needed to ensure that a compat task does
not map anything above 2GB. The TASK_SIZE limit for 31-bit
tasks is 2GB already and the generic code does check that a
resulting map address would not surpass that limit.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Move access_ok() in and pagefault_enable()/pagefault_disable() out.
Mechanical conversion only - some instances don't really need
a separate access_ok() at all (e.g. the ones only using
get_user()/put_user(), or architectures where access_ok()
is always true); we'll deal with that in followups.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Factor out check_asce_limit() function and fix few style
defects in arch_get_unmapped_area() family of functions.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
[heiko.carstens@de.ibm.com: small coding style changes]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
- mark sie control block as 512 byte aligned
- use fallthrough;
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=nsOM
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: cleanups for 5.7
- mark sie control block as 512 byte aligned
- use fallthrough;
When the support for polling drivers was initially added, it only
considered Input Queue 0. But as QDIO interrupts are actually for the
full device and not a single queue, this doesn't really fit for
configurations where multiple Input Queues are used.
Rework the qdio code so that interrupts for a polling driver are not
split up into actions for each queue. Instead deliver the interrupt as
a single event, and let the driver decide which queue needs what action.
When re-enabling the QDIO interrupt via qdio_start_irq(), this means
that the qdio code needs to
(1) put _all_ eligible queues back into a state where they raise IRQs,
(2) and afterwards check _all_ eligible queues for new work to bridge
the race window.
On the qeth side of things (as the only qdio polling driver), we can now
add CQ polling support to the main NAPI poll routine. It doesn't consume
NAPI budget, and to avoid hogging the CPU we yield control after
completing one full queue worth of buffers.
The subsequent qdio_start_irq() will check for any additional work, and
have us re-schedule the NAPI instance accordingly.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sie block must be aligned to 512 bytes. Mark it as such.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
When UID checking is enabled a UID value of 0 is invalid and can not be
set by the user. On z/VM it is however used to indicate an unset UID.
Until now, this lead to the behavior that one PCI function could be
attached with UID 0 after which z/VM would prohibit further attachment.
Now if the user then turns off UID checking in z/VM the user could
seemingly attach additional PCI functions that would however not show up
in Linux as that would not be informed of the change in UID checking
mode. This is unexpected and confusing and lead to bug reports against
Linux.
Instead now, if we encounter an unset UID value of 0 treat it as
indicating that UID checking was turned off, switch to automatic domain
allocation, and warn the user of the possible misconfiguration.
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Until now zpci_alloc_domain() only prevented more than
CONFIG_PCI_NR_FUNCTIONS from being added when using automatic domain
allocation. When explicit UIDs were defined UIDs above
CONFIG_PCI_NR_FUNCTIONS were not counted at all.
When more PCI functions are added this could lead to various errors
including under sized IRQ vectors and similar issues.
Fix this by explicitly tracking the number of allocated domains.
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Show number of cores that run at least one SMT thread
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Re-IPL for both CCW and FCP is currently done by using diag 308 with the
"Load Clear" subcode, which means that all memory will be cleared.
This can increase re-IPL duration considerably on very large machines.
For CCW devices, there is also a "Load Normal" subcode that was only used
for dump kernels so far. For FCP devices, a similar "Load Normal" subcode
was introduced with z14. The "Load Normal" diag 308 subcode allows to
re-IPL without clearing memory.
This patch adds a new "clear" sysfs attribute to /sys/firmware/reipl for
both the ccw and fcp subdirectories, which can be set to either "0" or "1"
to disable or enable re-IPL with memory clearing. The default value is "0",
which disables memory clearing.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The CPU topology masks on s390 contain also bits of CPUs which
are offline. Currently this is already a problem, since common
code scheduler expects e.g. cpu_smt_mask() to reflect reality.
This update changes the described behaviour and s390 starts to
behave like all other architectures.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Variable cpus_with_topology is a leftover that became
unneeded once the fake NUMA support has been removed.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Show CPU physical address as reported by STAP instruction
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
1. Allow to disable gisa
2. protected virtual machines
Protected VMs (PVM) are KVM VMs, where KVM can't access the VM's
state like guest memory and guest registers anymore. Instead the
PVMs are mostly managed by a new entity called Ultravisor (UV),
which provides an API, so KVM and the PV can request management
actions.
PVMs are encrypted at rest and protected from hypervisor access
while running. They switch from a normal operation into protected
mode, so we can still use the standard boot process to load a
encrypted blob and then move it into protected mode.
Rebooting is only possible by passing through the unprotected/normal
mode and switching to protected again.
One mm related patch will go via Andrews mm tree ( mm/gup/writeback:
add callbacks for inaccessible pages)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=x6Hn
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: Features and Enhancements for 5.7 part1
1. Allow to disable gisa
2. protected virtual machines
Protected VMs (PVM) are KVM VMs, where KVM can't access the VM's
state like guest memory and guest registers anymore. Instead the
PVMs are mostly managed by a new entity called Ultravisor (UV),
which provides an API, so KVM and the PV can request management
actions.
PVMs are encrypted at rest and protected from hypervisor access
while running. They switch from a normal operation into protected
mode, so we can still use the standard boot process to load a
encrypted blob and then move it into protected mode.
Rebooting is only possible by passing through the unprotected/normal
mode and switching to protected again.
One mm related patch will go via Andrews mm tree ( mm/gup/writeback:
add callbacks for inaccessible pages)
Now that all callers of kvm_free_memslot() pass NULL for @dont, remove
the param from the top-level routine and all arch's implementations.
No functional change intended.
Tested-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When userspace executes a syscall or gets interrupted,
BEAR contains a kernel address when returning to userspace.
This make it pretty easy to figure out where the kernel is
mapped even with KASLR enabled. To fix this, add lpswe to
lowcore and always execute it there, so userspace sees only
the lowcore address of lpswe. For this we have to extend
both critical_cleanup and the SWITCH_ASYNC macro to also check
for lpswe addresses in lowcore.
Fixes: b2d24b97b2 ("s390/kernel: add support for kernel address space layout randomization (KASLR)")
Cc: <stable@vger.kernel.org> # v5.2+
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Embedding the hotplug_slot in zdev structure allows to
greatly simplify the hotplug handling by eliminating
the handling of the slot_list.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Make page, frame, virtual and physical address conversion macros
more expressive by avoiding redundant definitions and defining
new macros using existing ones.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
On s390 there currently is no implementation of pud_write(). That was ok
as long as we had our own implementation of get_user_pages_fast() which
checked for pud protection by testing the bit directly w/o using
pud_write(). The other callers of pud_write() are not reachable on s390.
After commit 1a42010cdc ("s390/mm: convert to the generic
get_user_pages_fast code") we use the generic get_user_pages_fast(), which
does call pud_write() in pud_access_permitted() for FOLL_WRITE access on
a large pud. Without an s390 specific pud_write(), the generic version is
called, which contains a BUG() statement to remind us that we don't have a
proper implementation. This results in a kernel panic.
Fix this by providing an implementation of pud_write().
Cc: <stable@vger.kernel.org> # 5.2+
Fixes: 1a42010cdc ("s390/mm: convert to the generic get_user_pages_fast code")
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
For protected VMs, the VCPU resets are done by the Ultravisor, as KVM
has no access to the VCPU registers.
Note that the ultravisor will only accept a call for the exact reset
that has been requested.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Code 5 for the set cpu state UV call tells the UV to load a PSW from
the SE header (first IPL) or from guest location 0x0 (diag 308 subcode
0/1). Also it sets the cpu into operating state afterwards, so we can
start it.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
VCPU states have to be reported to the ultravisor for SIGP
interpretation, kdump, kexec and reboot.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
diag 308 subcode 0 and 1 require several KVM and Ultravisor interactions.
Specific to these "soft" reboots are
* The "unshare all" UVC
* The "prepare for reset" UVC
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The SPX instruction is handled by the ultravisor. We do get a
notification intercept, though. Let us update our internal view.
In addition to that, when the guest prefix page is not secure, an
intercept 112 (0x70) is indicated. Let us make the prefix pages
secure again.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[borntraeger@de.ibm.com: patch merging, splitting, fixing]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
