For Goodix GT917S chip, the chip ID string is "917S", which contains not
only numbers now.
Use string-based chip ID in the driver to support this chip and further
chips with alphanumber ID.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200228010146.12215-3-icenowy@aosc.io
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some devices with a goodix touchscreen have more then 1 capacitive
touch-key. This commit replaces the current support for a single
touch-key, which ignored the reported key-code. With support for
up to 7 touch-keys, based upon checking the key-code which is
post-fixed to any reported touch-data.
KEY_LEFTMETA is assigned to the first touch-key (it will still be
the default keycode for devices with a single touch-key).
KEY_F1, KEY_F2... are assigned as default keycode for the other
touch-keys.
This commit also add supports for keycode remapping, so that
systemd-udev's hwdb can be used to remap the codes to send
keycodes to match the icons on the buttons for devices with more
then 1 touch-key.
Signed-off-by: Dmitry Mastykin <dmastykin@astralinux.ru>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200316075302.3759-1-dmastykin@astralinux.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The goodix panel sends spurious interrupts after a 'finger up' event,
which always cause a timeout.
We were exiting the interrupt handler by reporting touch_num == 0, but
this was still processed as valid and caused the code to use the
uninitialised point_data, creating spurious key release events.
Report an error from the interrupt handler so as to avoid processing
invalid point_data further.
Signed-off-by: Dmitry Mastykin <dmastykin@astralinux.ru>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200316075302.3759-2-dmastykin@astralinux.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On some ACPI/x86 devices (where we use one of the ACPI IRQ pin access
methods) the firmware is buggy, it does not properly reset the controller
at boot, and we cannot communicate with it.
Normally on ACPI/x86 devices we do not want to reset the controller at
probe time since in some cases this causes the controller to loose its
configuration and this is loaded into it by the system's firmware.
So on these systems we leave the reset_controller_at_probe flag unset,
even though we have a access to both the IRQ and reset pins and thus
could reset it.
In the case of the buggy firmware we have to reset the controller to
actually be able to talk to it.
This commit adds a special case for this, if the goodix_i2c_test() fails,
and we have not reset the controller yet; and we do have a way to reset
the controller then retry the i2c-test after resetting the controller.
This fixes the driver failing at probe on ACPI/x86 systems with this
firmware bug.
Reported-and-tested-by: Dmitry Mastykin <dmastykin@astralinux.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200311191013.10826-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Our goodix_check_cfg_* helpers do things like:
int i, raw_cfg_len = cfg->size - 2;
...
if (check_sum != cfg->data[raw_cfg_len]) {
When cfg->size < 2, this will end up indexing the cfg->data array with
a negative value, which will not end well.
To fix this this commit adds a new GOODIX_CONFIG_MIN_LENGTH define and
adds a minimum size check for firmware-config files using this new define.
For consistency this commit also adds a new GOODIX_CONFIG_GT9X_LENGTH for
the length used for recent gt9xx and gt1xxx chips, instead of using
GOODIX_CONFIG_MAX_LENGTH for this, so that if other length defines get
added in the future it will be clear that the MIN and MAX defines should
contain the min and max values of all the other defines.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200307121505.3707-9-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On most Bay Trail (x86, UEFI + ACPI) devices the ACPI tables do not have
a _DSD with a "daffd814-6eba-4d8c-8a91-bc9bbf4aa301" UUID, adding
"irq-gpios" and "reset-gpios" mappings, so we cannot get the GPIOS by name
without first manually adding mappings ourselves.
These devices contain 2 GpioIo resource in their _CRS table, on all 4 such
devices which I have access to, the order of the 2 GPIOs is reset, int.
Note that the GPIO to which the touchscreen controller irq pin is connected
is configured in direct-irq mode on these Bay Trail devices, the
pinctrl-baytrail.c driver still allows controlling the pin as a GPIO in
this case, but this is not necessarily the case on other X86 ACPI
platforms, nor do we have a guarantee that the GPIO order is the same
elsewhere, so we limit the use of a _CRS table with 2 GpioIo resources
to Bay Trail devices only.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-5-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On most Cherry Trail (x86, UEFI + ACPI) devices the ACPI tables do not have
a _DSD with a "daffd814-6eba-4d8c-8a91-bc9bbf4aa301" UUID, adding
"irq-gpios" and "reset-gpios" mappings, so we cannot get the GPIOS by name
without first manually adding mappings ourselves.
These devices contain 1 GpioInt and 1 GpioIo resource in their _CRS table:
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Name (RBUF, ResourceTemplate ()
{
I2cSerialBusV2 (0x0014, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.PCI0.I2C2",
0x00, ResourceConsumer, , Exclusive,
)
GpioInt (Edge, ActiveLow, Shared, PullDefault, 0x0000,
"\\_SB.GPO1", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0013
}
GpioIo (Shared, PullDefault, 0x0000, 0x0000,
IoRestrictionOutputOnly,
"\\_SB.GPO1", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0019
}
})
Return (RBUF) /* \_SB_.PCI0.I2C2.TCS1._CRS.RBUF */
}
There is no fixed order for these 2. This commit adds code to check that
there is 1 of each as expected and then registers a mapping matching their
order using devm_acpi_dev_add_driver_gpios().
This gives us access to both GPIOs allowing us to properly suspend the
controller during suspend, and making it possible to reset the controller
if necessary.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200307121505.3707-4-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Before this commit we would always reset the controller at probe when we
have access to the GPIOs which are necessary to do a reset.
Doing the reset requires access to the GPIOs, but just because we have
access to the GPIOs does not mean that we should always reset the
controller at probe. On X86 ACPI platforms the BIOS / UEFI firmware will
already have reset the controller and it will have loaded the device
specific config into the controller. Doing the reset sometimes causes the
controller to lose its configuration, so on X86 ACPI platforms this is not
a good idea.
This commit adds a new reset_controller_at_probe boolean to control the
reset at probe behavior.
This commits sets the new bool to true when we set irq_pin_access_method
to IRQ_PIN_ACCESS_GPIO, so there are no functional changes.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-3-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
At least on X86 ACPI platforms it is not necessary to load the touchscreen
controller config from disk, if it needs to be loaded this has already been
done by the BIOS / UEFI firmware.
Even on other (e.g. devicetree) platforms the config-loading as currently
done has the issue that the loaded cfg file is based on the controller
model, but the actual cfg is device specific, so the cfg files are not
part of linux-firmware and this can only work with a device specific OS
image which includes the cfg file.
And we do not need access to the GPIOs at all to load the config, if we
do not have access we can still load the config.
So all in all tying the decision to try to load the config from disk to
being able to access the GPIOs is not desirable. This commit adds a new
load_cfg_from_disk boolean to control the firmware loading instead.
This commits sets the new bool to true when we set irq_pin_access_method
to IRQ_PIN_ACCESS_GPIO, so there are no functional changes.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
So far we have only effectively supported this on devices which use
devicetree. On X86 ACPI platforms both looking up the pins; and using a
pin as both IRQ and GPIO is a bit more complicated. E.g. on some devices
we cannot directly access the IRQ pin as GPIO and we need to call ACPI
methods to control it instead.
This commit adds a new irq_pin_access_method field to the goodix_chip_data
struct and adds goodix_irq_direction_output and goodix_irq_direction_input
helpers which together abstract the GPIO accesses to the IRQ pin.
This is a preparation patch for adding support for properly suspending the
touchscreen on X86 ACPI platforms.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200307121505.3707-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch supports reporting resolution for ABS_MT_TOUCH_MAJOR event.
This information is needed in showing pressure/width radius.
Signed-off-by: Johnny Chuang <johnny.chuang@emc.com.tw>
Reviewed-by: Harry Cutts <hcutts@chromium.org>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/1582766000-23023-1-git-send-email-johnny.chuang.emc@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchscreen on the Cube I15-TC don't match the default display,
with 0,0 touches being reported when touching at the top-right of
the screen.
Add a quirk to invert the x coordinate.
Reported-and-tested-by: Arkadiy <arkan49@yandex.ru>
Signed-off-by: Sergei A. Trusov <sergei.a.trusov@ya.ru>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When the distance thresholds are set the controller must be in reduced
reporting mode for them to have any effect on the interrupt generation.
This has a potentially large impact on the number of events the host
needs to process.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Link: https://lore.kernel.org/r/20200120111628.18376-1-l.stach@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds a platform driver for supporting keyboard and mouse
interface of SGI IOC3 chips.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Link: https://lore.kernel.org/r/20200122135220.22354-1-tbogendoerfer@suse.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are many devices, including several mobile battery-powered
devices, using other AXP variants as their PMIC. Allow them to use
the power key as a wakeup source.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20200115051253.32603-3-samuel@sholland.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Unlike most other power button drivers, this driver unconditionally
enables its wakeup IRQ. It should be using device_may_wakeup() to
respect the userspace configuration of wakeup sources.
Because the AXP20x MFD device uses regmap-irq, the AXP20x PEK IRQs are
nested off of regmap-irq's threaded interrupt handler. The device core
ignores such interrupts, so to actually disable wakeup, we must
explicitly disable all non-wakeup interrupts during suspend.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200115051253.32603-2-samuel@sholland.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20191210141103.15910-1-alexandru.ardelean@analog.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl4SYegeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG4m4H+QGCUN8SXN+2B+0/
BfzOf7PFoKzAx3NwDbJQIZqhSl+Zfa4n3VGPEF8sXsvoQgdYvuJnS/5JiAZ9iRIH
HAfFzegzQ3mCl8Du+SqCvQKs2Jt4OMCX62KGRebRBhpoKfZdwmN7n7pn9lWO771K
9rxTpeItXhmK46jOFRbi5oyQfmkfSfyUN1b9CB53FXFS+ZDkDNA7QQiIYnKOD7SZ
RrL7czhZ580QOC61qOlnz1GIhRzvU5SXg4OtuI3YfoOJRY5FKC3YtOgLReT0vPs+
vEhAyP93upVXIhqm10WHNjd4t4a45Vy5ff64uFsQ9QV4nnqsC2C70YwWbVDdtz/W
Lm0mvE8=
=NECs
-----END PGP SIGNATURE-----
Merge tag 'v5.5-rc5' into next
Sync up with mainline to get SPI "delay" API changes.
We do not have to handle the wake-irq within the driver because the pm
core can handle this for us. The only use case for the suspend/resume
callbacks was to handle the wake-irq so we can remove the callbacks.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since day one the touch controller acts as wakeup-source. This seems to
be wrong since the device supports deep-sleep mechanism [1] which
requires a reset to leave it. Also some designs won't use the
touchscreen as wakeup-source.
According discussion [2] we decided to break backward compatibility and
go the common way by using the 'wakeup-source' device-property.
[1] https://www.newhavendisplay.com/appnotes/datasheets/touchpanel/FT5x26.pdf
[2] https://patchwork.kernel.org/patch/11149037/
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It seems that the include order is historical increased and no one takes
care of it. Fix this to align it with the common rule to be in a
alphabetical order.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The EP0700MLP1 returns bogus data on the first register read access
(reading the threshold parameter from register 0x00):
edt_ft5x06 2-0038: crc error: 0xfc expected, got 0x40
It ignores writes until then. This patch adds a dummy read after which
the number of sensors and parameter read/writes work correctly.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The two device attrbitues are not declared outside this file
so make them static to avoid the following warnings:
drivers/input/misc/axp20x-pek.c:194:1: warning: symbol 'dev_attr_startup' was not declared. Should it be static?
drivers/input/misc/axp20x-pek.c:195:1: warning: symbol 'dev_attr_shutdown' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20191217152541.2167080-1-ben.dooks@codethink.co.uk
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To avoid flashing incompatible firmware onto a device we should check
whether "Remark ID" in firmware matches with the one in the controller.
This function is supported by Elan's latest version of boot code, so the
driver decides whether to perform the check based on the boot code version.
Signed-off-by: Johnny Chuang <johnny.chuang@emc.com.tw>
Link: https://lore.kernel.org/r/00a901d5af3c$193e9cd0$4bbbd670$@emc.com.tw
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull more input updates from Dmitry Torokhov:
- fixups for Synaptics RMI4 driver
- a quirk for Goodinx touchscreen on Teclast tablet
- a new keycode definition for activating privacy screen feature found
on a few "enterprise" laptops
- updates to snvs_pwrkey driver
- polling uinput device for writing (which is always allowed) now works
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers
Input: synaptics-rmi4 - re-enable IRQs in f34v7_do_reflash
Input: goodix - add upside-down quirk for Teclast X89 tablet
Input: add privacy screen toggle keycode
Input: uinput - fix returning EPOLLOUT from uinput_poll
Input: snvs_pwrkey - remove gratuitous NULL initializers
Input: snvs_pwrkey - send key events for i.MX6 S, DL and Q
This increment of rmi_smbus in rmi_smb_read/write_block() causes
garbage to be read/written.
The first read of SMB_MAX_COUNT bytes is fine, but after that
it is nonsense. Trial-and-error showed that by dropping the
increment of rmiaddr everything is fine and the F54 function
properly works.
I tried a hack with rmi_smb_write_block() as well (writing to the
same F54 touchpad data area, then reading it back), and that
suggests that there too the rmiaddr increment has to be dropped.
It makes sense that if it has to be dropped for read, then it has
to be dropped for write as well.
It looks like the initial work with F54 was done using i2c, not smbus,
and it seems nobody ever tested F54 with smbus. The other functions
all read/write less than SMB_MAX_COUNT as far as I can tell, so this
issue was never noticed with non-F54 functions.
With this change I can read out the touchpad data correctly on my
Lenovo X1 Carbon 6th Gen laptop.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://lore.kernel.org/r/8dd22e21-4933-8e9c-a696-d281872c8de7@xs4all.nl
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
F34 is a bit special as it reinitializes the device and related driver
structs during the firmware update. This clears the fn_irq_mask which
will then prevent F34 from receiving further interrupts, leading to
timeouts during the firmware update. Make sure to reinitialize the
IRQ enables at the appropriate times.
The issue is in F34 code, but the commit in the fixes tag exposed the
issue, as before this commit things would work by accident.
Fixes: 363c53875a (Input: synaptics-rmi4 - avoid processing unknown IRQs)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191129133514.23224-1-l.stach@pengutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchscreen on the Teclast X89 is mounted upside down in relation to
the display orientation (the touchscreen itself is mounted upright, but the
display is mounted upside-down). Add a quirk for this so that we send
coordinates which match the display orientation.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20191202085636.6650-1-hdegoede@redhat.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Gratuitous NULL initializers rarely help and often prevent compiler
from warning about using uninitialized variable. Let's remove them.
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/20191125211407.GA97812@dtor-ws
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* CrOS EC / MFD / IIO
- Contains tag-ib-chrome-mfd-iio-input-5.5, which is the first part of a
series from Gwendal to refactor sensor code between MFD, CrOS EC, iio
and input in order to add a new sensorhub driver and FIFO processing
* Wilco EC:
- Add support for Dell's USB PowerShare policy control, keyboard
backlight LED driver, and a new test_event file.
- Fixes use after free in wilco_ec's telemetry driver.
* Misc:
- bugfix in cros_usbpd_logger (missing destroy workqueue).
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCXeaqtwAKCRBzbaomhzOw
wilIAQCQ3/dpAwg2skKYYf3RBLDJeDLA1id7rNSgMOXc2aKyTAD/fCQtNhwj+Hal
W//04WWngTCQF5fkE9OCJrDwbm5eRwc=
=uOGe
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform changes from Benson Leung:
"CrOS EC / MFD / IIO:
- Contains tag-ib-chrome-mfd-iio-input-5.5, which is the first part
of a series from Gwendal to refactor sensor code between MFD, CrOS
EC, iio and input in order to add a new sensorhub driver and FIFO
processing
Wilco EC:
- Add support for Dell's USB PowerShare policy control, keyboard
backlight LED driver, and a new test_event file.
- Fixes use after free in wilco_ec's telemetry driver.
Misc:
- bugfix in cros_usbpd_logger (missing destroy workqueue)"
* tag 'tag-chrome-platform-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: wilco_ec: fix use after free issue
platform/chrome: cros_ec: Add Kconfig default for cros-ec-sensorhub
Revert "Input: cros_ec_keyb: mask out extra flags in event_type"
Revert "Input: cros_ec_keyb - add back missing mask for event_type"
platform/chrome: cros_ec: handle MKBP more events flag
platform/chrome: cros_ec: Do not attempt to register a non-positive IRQ number
platform/chrome: cros-ec: Record event timestamp in the hard irq
mfd / platform / iio: cros_ec: Register sensor through sensorhub
iio / platform: cros_ec: Add cros-ec-sensorhub driver
mfd / platform: cros_ec: Add sensor_count and make check_features public
platform/chrome: cros_ec: Put docs with the code
platform/chrome: cros_usbpd_logger: add missed destroy_workqueue in remove
platform/chrome: cros_ec: Fix Kconfig indentation
platform/chrome: wilco_ec: Add keyboard backlight LED support
platform/chrome: wilco_ec: Add charging config driver
platform/chrome: wilco_ec: Add Dell's USB PowerShare Policy control
platform/chrome: wilco_ec: Add debugfs test_event file
The first generation i.MX6 processors does not send an interrupt when the
power key is pressed. It sends a power down request interrupt if the key is
released before a hard shutdown (5 second press). This should allow
software to bring down the SoC safely.
For this driver to work as a regular power key with the older SoCs, we need
to send a keypress AND release when we get the power down request irq.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Link: https://lore.kernel.org/r/20191125161210.8275-1-robin@protonic.nl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The v4l2-compliance utility reported several V4L2 API compliance
issues:
- the sequence counter wasn't filled in
- the sequence counter wasn't reset to 0 at the start of streaming
- the returned field value wasn't set to V4L2_FIELD_NONE
- the timestamp wasn't set
- the payload size was undefined if an error was returned
- min_buffers_needed doesn't need to be initialized
Fix these issues.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de
Link: https://lore.kernel.org/r/20191119105118.54285-3-hverkuil-cisco@xs4all.nl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/1574306373-29581-1-git-send-email-krzk@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This reverts commit 68b9c5066e39af41d3448abfc887c77ce22dd64d.
Ugh, I really dropped the ball on this one :\. So as it turns out RMI4
works perfectly fine on the X1 Extreme Gen 2 except for one thing I
didn't notice because I usually use the trackpoint: clicking with the
touchpad. Somehow this is broken, in fact we don't even seem to indicate
BTN_LEFT as a valid event type for the RMI4 touchpad. And, I don't even
see any RMI4 events coming from the touchpad when I press down on it.
This only seems to work for PS/2 mode.
Since that means we have a regression, and PS/2 mode seems to work fine
for the time being - revert this for now. We'll have to do a more
thorough investigation on this.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20191119234534.10725-1-lyude@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This reverts commit d096aa3eb6.
This patch is not needed anymore since we clear EC_MKBP_HAS_MORE_EVENTS
flag before calling the notifiers in patch
"9d9518f5b52a (platform: chrome: cros_ec: handle MKBP more events flag)"
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
This reverts commit 62c3801619.
This patch is not needed anymore since we clear EC_MKBP_HAS_MORE_EVENTS
flag before calling the notifiers in patch
"9d9518f5b52a (platform: chrome: cros_ec: handle MKBP more events flag)"
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Just got one of these for debugging some unrelated issues, and noticed
that Lenovo seems to have gone back to using RMI4 over smbus with
Synaptics touchpads on some of their new systems, particularly this one.
So, let's enable RMI mode for the X1 Extreme 2nd Generation.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20191115221814.31903-1-lyude@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver forgets to destroy workqueue in remove() similarly to what is
done when probe() fails. Add a call to destroy_workqueue() to fix it.
Since unregistration will wait for the work to finish, we do not need to
cancel/flush the work instance in remove().
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191114023405.31477-1-hslester96@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
