After the fix from Jiri that disabled local IRQs instead of
just BHs (necessary to fix an issue with submitting a command
with IRQs already disabled), there was still a situation in
which we could deep in there enable BHs, if the device config
sets the apmg_wake_up_wa configuration, which is true on all
7000 series devices.
To fix that, but not require reverting commit 1ed08f6fb5
("iwlwifi: remove flags argument for nic_access"), split up
nic access into a version with BH manipulation to use most
of the time, and without it for this specific case where the
local IRQs are already disabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210415164821.d0f2edda1651.I75f762e0bed38914d1300ea198b86dd449b4b206@changeid
iwlwifi patches intended for v5.12
* Check FW notification sizes for robustness;
* Improvements in the NAPI implementation;
* Implement a workaround for CCA-EXT;
* Add new FW API support;
* Fix a CSA bug;
* Implement PHY integration version parsing;
* A bit of refactoring;
* One more CSA bug fix, this time in the AP side;
* Support for new So devices and a bit of reorg;
* Per Platform Antenna Gain (PPAG) fixes and improvements;
* Improvements in the debug framework;
* Some other clean-ups and small fixes.
# gpg: Signature made Fri 05 Feb 2021 12:04:21 PM EET using RSA key ID 1A3CC5FA
# gpg: Good signature from "Luciano Roth Coelho (Luca) <luca@coelho.fi>"
# gpg: aka "Luciano Roth Coelho (Intel) <luciano.coelho@intel.com>"
If we spin for a long time in memory reads that (for some reason in
hardware) take a long time, then we'll eventually get messages such
as
watchdog: BUG: soft lockup - CPU#2 stuck for 24s! [kworker/2:2:272]
This is because the reading really does take a very long time, and
we don't schedule, so we're hogging the CPU with this task, at least
if CONFIG_PREEMPT is not set, e.g. with CONFIG_PREEMPT_VOLUNTARY=y.
Previously I misinterpreted the situation and thought that this was
only going to happen if we had interrupts disabled, and then fixed
this (which is good anyway, however), but that didn't always help;
looking at it again now I realized that the spin unlock will only
reschedule if CONFIG_PREEMPT is used.
In order to avoid this issue, change the code to cond_resched() if
we've been spinning for too long here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 04516706bb ("iwlwifi: pcie: limit memory read spin time")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210115130253.217a9d6a6a12.If964cb582ab0aaa94e81c4ff3b279eaafda0fd3f@changeid
We no longer need code that was introduced to differentiate
between two early versions of 8260.
We can remove this convoluted way to get the hardware version
that was needed because of a bug in the register's
configuration.
Moreover, since we no longer need to access the PRPH
registers, we no longer need to wake up the device,
request ownership, etc...
Remove all that.
This allows us to get the rid of the obsolete comment
about the AUX bus MISC address space which should have
been moved when this code was moved away from here.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.4a5665ccd8a6.Iff3879405c15758ba661c430e77dc2160ddada1c@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we read device memory, we lock a spinlock, write the address we
want to read from the device and then spin in a loop reading the data
in 32-bit quantities from another register.
As the description makes clear, this is rather inefficient, incurring
a PCIe bus transaction for every read. In a typical device today, we
want to read 786k SMEM if it crashes, leading to 192k register reads.
Occasionally, we've seen the whole loop take over 20 seconds and then
triggering the soft lockup detector.
Clearly, it is unreasonable to spin here for such extended periods of
time.
To fix this, break the loop down into an outer and an inner loop, and
break out of the inner loop if more than half a second elapsed. To
avoid too much overhead, check for that only every 128 reads, though
there's no particular reason for that number. Then, unlock and relock
to obtain NIC access again, reprogram the start address and continue.
This will keep (interrupt) latencies on the CPU down to a reasonable
time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201022165103.45878a7e49aa.I3b9b9c5a10002915072312ce75b68ed5b3dc6e14@changeid
To avoid duplicating code we need to call iwl_pcie_txq_update_byte_cnt_tbl
function from non bus independent code so make it bus independent.
Used spatch rule
@r1@
struct iwl_trans_pcie *trans_pcie;
@@
(
-trans_pcie->scd_bc_tbls
+trans->txqs.scd_bc_tbls
|
-iwl_pcie_txq_update_byte_cnt_tbl
+iwl_txq_gen1_update_byte_cnt_tbl
|
-iwl_pcie_txq_inval_byte_cnt_tbl
+iwl_txq_gen1_inval_byte_cnt_tbl
|
-iwl_pcie_tfd_unmap
+iwl_txq_gen1_tfd_unmap
|
-iwl_pcie_tfd_tb_get_addr
+iwl_txq_gen1_tfd_tb_get_addr
|
-iwl_pcie_tfd_tb_get_len
+iwl_txq_gen1_tfd_tb_get_len
|
-iwl_pcie_tfd_get_num_tbs
+iwl_txq_gen1_tfd_get_num_tbs
)
/* clean all new unused variables */
@ depends on r1@
type T;
identifier i;
expression E;
@@
- T i = E;
... when != i
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930191738.8d33e791ec8c.Ica35125ed640aa3aa1ecc38fb5e8f1600caa8df6@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't want to have txq code in the PCIe transport code, so move all
the relevant elements to a new iwl_txq structure and store it in
iwl_trans.
spatch
@ replace_pcie @
struct iwl_trans_pcie *trans_pcie;
@@
(
-trans_pcie->queue_stopped
+trans->txqs.queue_stopped
|
-trans_pcie->queue_used
+trans->txqs.queue_used
|
-trans_pcie->txq
+trans->txqs.txq
|
-trans_pcie->txq
+trans->txqs.txq
|
-trans_pcie->cmd_queue
+trans->txqs.cmd.q_id
|
-trans_pcie->cmd_fifo
+trans->txqs.cmd.fifo
|
-trans_pcie->cmd_q_wdg_timeout
+trans->txqs.cmd.wdg_timeout
)
// clean all new unused variables
@ depends on replace_pcie @
type T;
identifier i;
expression E;
@@
- T i = E;
... when != i
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200529092401.a428d3c9d66f.Ie04ae55f33954636a39c98e7ae1e739c0507435b@changeid
These values are selected based on the PCI device ID, so the decision
to use them can be made early. By moving them to the trans_cfg, we
avoid duplicating the large cfg structs for small pieces of
data (sometimes a single boolean). This will also allow us to make
more decisions based on, for instance, the SoC type in used.
The trans_cfg concept changes a bit, because previously it was used
only to boot the device before reading further characteristics and now
it also contains more data that is associated with the device ID.
Change-Id: Ib71b07ea9e322eb74571dc5e8aa58f17eece5c9c
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the read_config32 op to allow dumping the config space when
needed.
Change-Id: Ib2d254a38a4bfb95dcc3d04eec91781827a0c623
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Kalle Valo says:
====================
wireless-drivers-next patches for v5.6
Second set of patches for v5.6. Nothing special standing out, smaller
new features and fixes allover.
Major changes:
ar5523
* add support for SMCWUSBT-G2 USB device
iwlwifi
* support new versions of the FTM FW APIs
* support new version of the beacon template FW API
* print some extra information when the driver is loaded
rtw88
* support wowlan feature for 8822c
* add support for WIPHY_WOWLAN_NET_DETECT
brcmfmac
* add initial support for monitor mode
qtnfmac
* add module parameter to enable DFS offloading in firmware
* add support for STA HE rates
* add support for TWT responder and spatial reuse
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of patches intended for v5.6
* Support new versions of the FTM FW APIs;
* Fix an old bug in D3 (WoWLAN);
* A couple of fixes/improvements in the receive-buffers code;
* Fix in the debugging where we were skipping one TXQ;
* Support new version of the beacon template FW API;
* Print some extra information when the driver is loaded;
* Some debugging infrastructure (aka. yoyo) updates;
* Support for a new HW version;
* Second phase of device configuration work started;
* Some clean-ups;
