This patch reverts commit 6e0a32d6f3 ("spi: dw: Fix default polarity
of native chipselect").
The SPI framework always called the set_cs callback with the logic
level it desired on the chip select line, which is what the drivers
original handling supported. commit f3186dd876 ("spi: Optionally
use GPIO descriptors for CS GPIOs") changed these symantics, but only
in the case of drivers that also support GPIO chip selects, to true
meaning apply slave select rather than logic high. This left things in
an odd state where a driver that only supports hardware chip selects,
the core would handle polarity but if the driver supported GPIOs as
well the driver should handle polarity. At this point the reverted
change was applied to change the logic in the driver to match new
system.
This was then broken by commit 3e5ec1db8b ("spi: Fix SPI_CS_HIGH
setting when using native and GPIO CS") which reverted the core back
to consistently calling set_cs with a logic level.
This fix reverts the driver code back to its original state to match
the current core code. This is probably a better fix as a) the set_cs
callback is always called with consistent symantics and b) the
inversion for SPI_CS_HIGH can be handled in the core and doesn't need
to be coded in each driver supporting it.
Fixes: 3e5ec1db8b ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191127153936.29719-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Committed version of the commit b9fc2d207e ("spi: dw: Move runtime PM
enable/disable from common to platform driver part") does not include by
some reason changes to drivers/spi/spi-dw.c that were part of the original
patch sent to the mailing list.
Complete the code move by doing those changes now.
Fixes: b9fc2d207e ("spi: dw: Move runtime PM enable/disable from common to platform driver part")
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20191030113137.15459-1-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable runtime PM so that the clock used to access the registers in the
peripheral is turned on using a clock domain.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Gareth Williams <gareth.williams.jx@renesas.com>
Link: https://lore.kernel.org/r/1568793876-9009-4-git-send-email-gareth.williams.jx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DW controller also supports platforms specifying
native chipselects. When I enforce the use of high CS
for drivers opting in for using GPIO descriptors, I
inadvertedly switched the driver to also use active
high chip select for native chip selects.
As it turns out, the DW hardware driving chip selects
also thinks it is weird with active low chip selects
so all we need to do is remove an inversion in the
driver.
Cc: Jan Kotas <jank@cadence.com>
Reported-by: Jan Kotas <jank@cadence.com>
Tested-by: Jan Kotas <jank@cadence.com>
Fixes: 9400c41e77 ("spi: dw: Convert to use CS GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change snprintf to scnprintf. There are generally two cases where using
snprintf causes problems.
1) Uses of size += snprintf(buf, SIZE - size, fmt, ...)
In this case, if snprintf would have written more characters than what the
buffer size (SIZE) is, then size will end up larger than SIZE. In later
uses of snprintf, SIZE - size will result in a negative number, leading
to problems. Note that size might already be too large by using
size = snprintf before the code reaches a case of size += snprintf.
2) If size is ultimately used as a length parameter for a copy back to user
space, then it will potentially allow for a buffer overflow and information
disclosure when size is greater than SIZE. When the size is used to index
the buffer directly, we can have memory corruption. This also means when
size = snprintf... is used, it may also cause problems since size may become
large. Copying to userspace is mitigated by the HARDENED_USERCOPY kernel
configuration.
The solution to these issues is to use scnprintf which returns the number of
characters actually written to the buffer, so the size variable will never
exceed SIZE.
Signed-off-by: Silvio Cesare <silvio.cesare@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When CONFIG_SPI_DESIGNWARE are enabled we see the unused variable
warning in dw_spi_setup.
../drivers/spi/spi-dw.c: In function ‘dw_spi_setup’:
../drivers/spi/spi-dw.c:400:6: warning: unused variable ‘ret’ [-Wunused-variable]
int ret;
^~~
Remove the unused varable.
Fixes: 9400c41e77 ("spi: dw: Convert to use CS GPIO descriptors")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the DesignWare (dw) SPI master driver to
use GPIO descriptors for chip select handling.
This driver has a duplicate DT parser in addition to the
one in the core, sets up the line as non-asserted and
relies on the core to drive the GPIOs.
It is a pretty straight-forward conversion.
Cc: Talel Shenhar <talel@amazon.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Linuxarm <linuxarm@huawei.com>
Tested-by: Jay Fang <f.fangjian@huawei.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
spi::mode is defined by framework for several SPI capabilities,
such as polarity, phase, bit-endian, wire number. Directly use this
variable for setting controller's polarity and phase causes other
bit in register being set. Since SPI framework has its definition,
SPI_CPOL and SPI_CPHA offset may be changed by framwork change.
Instead of just mask off the relevant bits,
fetch required bit in spi::mode and set to register.
Signed-off-by: shaftarger <shol@livemail.tw>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Hisilicon Hip08 platform, that uses ACPI, has this controller.
Let's add ACPI support for DW SPI MMIO-based host.
The ACPI ID used is "HISI0173" for the Designware SPI controller of
Hisilicon Hip08 platform.
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for a new devicetree compatible string called
'amazon,alpine-apb-ssi', which is necessary for the Amazon Alpine spi
controller. 'amazon,alpine-dw-apb-ssi' is used in the dw spi driver if
specified in the devicetree. Otherwise, fall back to driver default
behavior, i.e. original dw IP hw driver behavior.
Signed-off-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-dw driver currently only supports 8 or 16 bits per word.
Since the hardware supports 4-16 bits per word, adapt the driver
to also support this.
Tested on socfpga cyclone5 with a 9-bit SPI display.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_controller_{suspend,resume}() already prints an error message on
failure, so there is no need to repeat this in individual drivers.
Note: spi_master_{suspend,resume}() is an alias for
spi_controller_{suspend,resume}().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Daniel Mack <daniel@zonque.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Export dw_spi_set_cs so it can be used from the various IP integration
modules.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow platform specific drivers to provide their own set_cs callback when
the IP integration requires it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is possible to get an interrupt as soon as it is requested. dw_spi_irq
does spi_controller_get_devdata(master) and expects it to be different than
NULL. However, spi_controller_set_devdata() is called after request_irq(),
resulting in the following crash:
CPU 0 Unable to handle kernel paging request at virtual address 00000030, epc == 8058e09c, ra == 8018ff90
[...]
Call Trace:
[<8058e09c>] dw_spi_irq+0x8/0x64
[<8018ff90>] __handle_irq_event_percpu+0x70/0x1d4
[<80190128>] handle_irq_event_percpu+0x34/0x8c
[<801901c4>] handle_irq_event+0x44/0x80
[<801951a8>] handle_level_irq+0xdc/0x194
[<8018f580>] generic_handle_irq+0x38/0x50
[<804c6924>] ocelot_irq_handler+0x104/0x1c0
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert to generalized SPI controller API introduced by the
commit 8caab75fd2 ("spi: Generalize SPI "master" to "controller"").
Inside driver variable name "master" is still used to indicate the driver
is master only.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Local struct chip_data has two members that are not used:
- cs. Looks like was never used
- enable_dma. Became unused by the commit f89a6d8f43 ("spi: dw-mid: move
to use core SPI DMA mappings").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of using device name it was suggested that bus number was more
appropriate to differentiate debugfs names. Also reduce buffer size to
more realistic 32 bytes instead of 128.
When request_irq is called the bus number may not be assigned. Therefore
the irq name was not unique when dynamic bus number was being used.
As per most of the spi drivers use the device name instead. No other
use of dws->name could be found so it was removed.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some system have multiple dw devices. Currently the driver uses a
fixed name for the debugfs dir. Append dev name to the debugfs dir
name to make it unique.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Designware SPI master requires slave selection before the transfer
can begin [1].
This patch uses the new master flag to indicate both the GPIO CS and
the internal chip select should be used.
Tested On:
Altera CycloneV development kit
Compile tested for build errors on x86_64 (allyesconfigs)
[1] DesignWare dw_apb_ssi Databook, Version 3.20a (page 39)
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Avoid ending up with a higher frequency than requested
Signed-off-by: Matthias Seidel <kernel@mseidel.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add current master clock to dws struct and compare it against the
requestedtransfer speed. Update clock divider only if necessary.
Signed-off-by: Matthias Seidel <kernel@mseidel.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TMODE available value is well defined and documented in the header
file. Use it and remove the comment.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The offset 0x60 is the offset of the data register defined as DW_SPI_DR in the
header file. Use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently all users aware about calling dw_spi_remove_host() with properly set
parameter. Remove unneeded check.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This helper disables SPI controller and sets clock to 0.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The tx_threshold and rx_threshold variables are not used anywhere. Remove them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no point to have a separate variable for speed in ->transfer_one().
While here, remove !chip->clk_div from a condition since it is assigned
simultaneously with chip->speed_hz. We can do this safely because
a) transfer speed can't be higher than max_freq and therefore chip->clk_div
can be 0 only when chip->speed_hz is 0, and
b) transfer speed can't be 0, otherwise we will get division by zero
exception.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to carry over spi->bits_per_word and Co from ->setup() in
struct chip_data since ->transfer_one() will anyway take the transfer
parameters from struct spi_transfer. This is since SPI core validates both
bits_per_word transfer parameter and defaults to spi->bits_per_word in case
that per transfer parameter is not set.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we recalculate cr0 each time we start a transfer the chip_data->cr0
becomes redundant. Remove it and related pieces.
This is a follow up to commit 0ed36990a9 (spi: dw: Remove needless if
statements).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The name of the master device is set during registrationg which happens after
we issue the error message. Change it to plain struct device * to see which
device registration failed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Test for non-zero spi->max_speed_hz in dw_spi_setup() looks needless as
spi_setup() defaults to master->max_speed_hz in case it is not set. This
drivers sets the master->max_speed_hz based on max_freq data passed to it
via dw_spi_add_host() call. I suppose things have already fallen apart if
dw_spi_mmio_probe() or spi_pci_probe() ever passes zero max_freq.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates both bits_per_word and speed_hz transfer parameters and
defaults to spi->bits_per_word and spi->max_speed_hz in case these per
transfer parameters are not set. This allows to remove related if
statements as they evaluate always to true and reduce indentation.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit dd11444327 ("spi: dw-spi: Convert 16bit accesses to 32bit
accesses") changed all 16bit accesses in the DW_apb_ssi driver to 32bit.
This, unfortunately, breaks data register access on picoXcell, where the
DW IP needs data register accesses to be word accesses (all other
accesses appear to be OK).
This change introduces a new master variable to allow interface drivers
to specify that 16bit data transfer I/O is required. This change also
introduces the ability to set this variable via device tree bindings in
the MMIO interface driver. Both the core and the MMIO interface driver
default to the current 32bit behaviour.
Before this change, on a picoXcell pc3x3:
spi_master spi32766: interrupt_transfer: fifo overrun/underrun
m25p80 spi32766.0: error -5 reading 9f
m25p80: probe of spi32766.0 failed with error -5
After this change:
m25p80 spi32766.0: m25p40 (512 Kbytes)
Fixes: dd11444327 ("spi: dw-spi: Convert 16bit accesses to 32bit accesses")
Signed-off-by: Michael van der Westhuizen <michael@smart-africa.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit 1a7b7ee72c (spi: Ensure that CS line is in non-active state after
spi_setup()) introduces an unconditional call of spi_set_cs() before ->setup().
The dw_spi_set_cs() relies on that fact that ->setup() is already called, but
it doesn't now. This patch fixes the crash by adding an additional check to
dw_spi_set_cs().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Altera's Arria10 SoC interconnect requires a 32-bit write for APB
peripherals. The current spi-dw driver uses 16-bit accesses in
some locations. This patch converts all the 16-bit reads and
writes to 32-bit reads and writes.
Additional Documentation to Support this Change:
The DW_apb_ssi databook states:
"All registers in the DW_apb_ssi are addressed at 32-bit boundaries
to remain consistent with the AHB bus. Where the physical size of
any register is less than 32-bits wide, the upper unused bits of
the 32-bit boundary are reserved. Writing to these bits has no
effect; reading from these bits returns 0." [1]
[1] Section 6.1 of dw_apb_ssi.pdf (version 3.22a)
Request for test with platforms using the DesignWare SPI IP.
Tested On:
Altera CycloneV development kit
Altera Arria10 development kit
Compile tested for build errors on x86_64 (allyesconfigs)
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Reviewed-and-tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of clearing the RxU, RxO, and TxO IRQs individually with
3 register reads, a single read of the ICR register will do the
same thing.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core has a comprehensive function set to map and unmap a message when it's
needed. This patch converts driver to use that advantage.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch shuts up any ongoing DMA transfer in case of error.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch splits DMA preparatory code to dma_setup() callback. The change also
converts transfer_one() to program DMA whenever the transfer is DMA mapped. The
change is a follow up of the converion to use SPI core transfer_one_message().
Since the DMA mapped transfers can be interleaved with PIO ones the DMA related
configuration should respect that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMAEngine has a specific type to be used for bus width. This patch converts the
code to use the values of the specific type when configure DMA transfer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch removes a lot of duplicate code since SPI core provides a nice
message handling.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch refactors the code in pump_transfers() to reprogram the registers
immediately when we have a new configuration data. The behaviour is slightly
modified:
- chip is always disabled and reenabled
- CTRL0 is always reprogrammed
This change allows to do a further refactoring and simplier conversion to use
SPI core DMA routines in the future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The error handling is partially broken since the controller is disabled on
error and is not re-enabled until condition occurs, i.e. mode (poll, PIO/DMA),
chip (cs_change), or speed (clk_div) is changed. In the result of these changes
we will have a predictable state of the SPi controller independently on how
successfull was a previous transfer.
The patch disables interrupts and re-enables the SPI controller wherever it
needs to be done. Thus most of the time the SPI controller is kept enabled. The
runtime PM, when it will be implemented, must take care of the controller
disabling and re-enabling.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit d297933cc7 (spi: dw: Fix detecting FIFO depth) tries to fix the
logic of the FIFO detection based on the description on the comments. However,
there is a slight difference between numbers in TX Level and TX FIFO size.
So, by specification the FIFO size would be in a range 2-256 bytes. From TX
Level prospective it means we can set threshold in the range 0-(FIFO size - 1)
bytes. Hence there are currently two issues:
a) FIFO size 2 bytes is actually skipped since TX Level is 1 bit and could be
either 0 or 1 byte;
b) FIFO size is incorrectly decreased by 1 which already done by meaning of
TX Level register.
This patch fixes it eventually right.
Fixes: d297933cc7 (spi: dw: Fix detecting FIFO depth)
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
