Do not reset GPIO5 at boot-up because GPIO5_7 is used
on AM437x GP-EVM to control VTT regulators on DDR3.
Without this some GP-EVM boards will fail to boot because
of DDR3 corruption.
Reported-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IGEPv2 board has a SMSC LAN9221i ethernet chip and not a
SMSC LAN911x connected to the GPMC. Each chip needs different
timings in order to operate correctly so is wrong to include
omap-gpmc-smsc911x.dtsi instead of omap-gpmc-smsc9221.dtsi.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
[tony@atomide.com: this is needed to avoid potential memory corruption]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Sending a SIGTRAP to a user task after execution of a BRK instruction at
EL0 is fundamental to the way in which software breakpoints work and
doesn't deserve a warning to be logged in dmesg. Whilst the warning can
be justified from EL1, do_debug_exception will already do the right thing,
so simply remove the code altogether.
Cc: Sandeepa Prabhu <sandeepa.prabhu@linaro.org>
Reported-by: Kyrylo Tkachov <kyrylo.tkachov@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When arm64 moved over to the core mmu_gather, it lost the logic to
flush THP TLB entries (tlb_remove_pmd_tlb_entry was removed and the
core implementation only signals that the mmu_gather needs a flush).
This patch ensures that tlb_add_flush is called for THP TLB entries.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The A register needs to be initialized to zero in the prolog if the
first instruction of the BPF program is BPF_S_LDX_B_MSH to prevent
leaking the content of %r5 to user space.
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Some Marvell PJ4B CPUs also implement iWMMXt extensions. With a
proper check for iWMMXt coprocessors now in place, enable it by
default on PJ4B. While at it, also allow to manually select
the corresponding Kconfig option.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit fdb487f5c9
("ARM: 8015/1: Add cpu_is_pj4 to distinguish PJ4 because it
has some differences with V7")
introduced a cpuid check for Marvell PJ4 processors to fix a
regression caused by adding PJ4 based Marvell Dove into
multi_v7.
Unfortunately, this check is too narrow to catch PJ4 used on
Dove itself and breaks iWMMXt support.
This patch therefore relaxes the cpuid mask to match both PJ4
and PJ4B. Also, rework the given comment about PJ4/PJ4B
modifications to be a little bit more specific about the
differences.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
commit fdb487f5c9
("ARM: 8015/1: Add cpu_is_pj4 to distinguish PJ4 because it
has some differences with V7")
introduced a fix for checking PJ4 cpuid to not use PJ4 specific
coprocessor access on non-PJ4 platforms.
Unfortunately, this in turn broke Marvell Armada 370/XP, both
comprising Marvell PJ4B CPUs without iWMMXt extension. Instead
of only checking for cpuid, which may not be sufficient to
determine iWMMXt support, the presence of iWMMXt coprocessors
can be checked by enabling and reading the Coprocessor ID
register (wCID, register 0 of CP1).
Therefore this adds an explicit check for the presence and correct
wCID value, before enabling iWMMXt capabilities. As a bonus, also
print the iWMMXt version of a detected coprocessor.
This has been tested to properly detect iWMMXt presence/absence on:
- PJ4, CPUID 0x560f5815, wCID 0x56052001: Marvell Dove, iWMMXt v2
- PJ4B, CPUID 0x561f5811: Marvell Armada 370, no iWMMXt
- PJ4B, CPUID 0x562f5841, wCID 0x56052001: Marvell Armada 1500, iWMMXt v2
- PJ4B, CPUID 0x562f5842: Marvell Armada XP, no iWMMXt
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes PJ4 coprocessor init to only expose iWMMXt capabilities,
if the corresponding kernel support for iWMMXt is enabled.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
iwmmxt.S requires special treatment of coprocessor access registers
for PJ4 and XScale-based CPUs. It only checks for CPU_PJ4 and drops
down to XScale-based treatment on all other architectures.
As some PJ4B also come with iWMMXt and also need PJ4 treatment,
rework the corresponding preprocessor directives to explicitly
check for supported architectures and fail on unsupported ones.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This series contains straight-forward fixes for different
Versatile Express infrastructure drivers:
- NULL pointer dereference on the error path in the clk driver
- out of boundary array access in the dcscb driver
- broken restart/power off implementation
- mis-interpreted voltage unit in the spc driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJTWTroAAoJEL9jRaJfXa5PHMkIAJB2S6zuqIxn7qRsfeD5YauR
nz7AHjDaakoVy6YTaMdHQI+dXSK6BPUNvMbrKzW3WWbT4ktJ/r3k/OeeBv/2T93L
8KW1Bbif7kPfdfITwCCWDs5waTDVXSBC6AGGoXomzQIt4MqghhzoLRc6uvhnuYAL
R7ZJsTWRa+47LVOJsghVffMyNlwCMj//prW7PBY6RIZXhpcbI+FGYv5Rm1XRITWn
uL2cSulBmWeqMVCR/gFx8/K5TqZ90q835dD1Ggh+BeB1Vaifu9/cI3D8w0hl/xy9
nRneKdTaTEpKjgwI3up4vMFbLbMI7brdMphZ9ZeGgK+YuWXFDbKvvdwjvDJ4Tx0=
=BS4Q
-----END PGP SIGNATURE-----
Merge tag 'vexpress/fixes-for-3.15' of git://git.linaro.org/people/pawel.moll/linux into fixes
ARM Versatile Express fixes for 3.15
This series contains straight-forward fixes for different
Versatile Express infrastructure drivers:
- NULL pointer dereference on the error path in the clk driver
- out of boundary array access in the dcscb driver
- broken restart/power off implementation
- mis-interpreted voltage unit in the spc driver
* tag 'vexpress/fixes-for-3.15' of git://git.linaro.org/people/pawel.moll/linux:
ARM: vexpress/TC2: Convert OPP voltage to uV before storing
power/reset: vexpress: Fix restart/power off operation
arm/mach-vexpress: array accessed out of bounds
clk: vexpress: NULL dereference on error path
Includes an update to 3.15-rc2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A few driver specific fixes here:
- SH HSPI was dealing with its clocks incorrectly which meant it didn't
work on some SoCs, fixing this also requires a small fix to one of
the SoC clock trees to avoid breaking existing users.
- The SiRF driver appears to have had several quality problems, it's
fairly new and not widely used so this isn't too worrying.
- A brute force fix for excessive locking in the Atmel driver, it needs
further investigation but this deals with the immediate issue.
- A build fix for the Blackfin driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kM6u
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few driver specific fixes here:
- SH HSPI was dealing with its clocks incorrectly which meant it
didn't work on some SoCs, fixing this also requires a small fix to
one of the SoC clock trees to avoid breaking existing users.
- The SiRF driver appears to have had several quality problems, it's
fairly new and not widely used so this isn't too worrying.
- A brute force fix for excessive locking in the Atmel driver, it
needs further investigation but this deals with the immediate
issue.
- A build fix for the Blackfin driver"
* tag 'spi-v3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: atmel: Fix scheduling while atomic bug
spi: sh-hspi: Do not specifically request shyway_clk clock
ARM: shmobile: r8a7778: Use clks as MSTP007 parent
spi: sirf: make GPIO chipselect function work well
spi: sirf: set SPI controller in RISC IO chipselect mode
spi: sirf: correct TXFIFO empty interrupt status bit
spi: bfin5xx: fix build error
Pull dma-mapping fix from Marek Szyprowski:
"A small fix for dma-mapping subsystem for ARM"
* 'fixes_for_v3.15' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
arm: dma-mapping: Fix mapping size value
The SPC stores voltage in mV while the code assumes it was returning
uV. Convert the returned voltage to uV before storing. Also fix the
comment depicting voltage to uV.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Tegra124 only has 4 UARTs. Parts of the documentation hint at a fifth
UART, but this appears to be left-over from earlier SoC documentation.
Remove the non-existent DT node for UART5.
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
device tree based booting. And turns out BeagleBoard xM A/B
needs it's own minimal dts in addition to the related u-boot
changes. Also few minor documentation and typo fixes are merged
to get them out of the way.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=co/l
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps, mostly to fix some GPMC, DSS and USB issues for
device tree based booting. And turns out BeagleBoard xM A/B
needs it's own minimal dts in addition to the related u-boot
changes. Also few minor documentation and typo fixes are merged
to get them out of the way.
* tag 'omap-for-v3.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix GPMC remap for devices using an offset
ARM: OMAP2+: Fix oops for GPMC free
ARM: dts: Add support for the BeagleBoard xM A/B
ARM: dts: Grammar /that will/it will/
ARM: dts: Grammar /is uses/ is used/
ARM: OMAP2+: Fix config name for USB3 PHY
ARM: dts: am335x: update USB DT references
ARM: dts: OMAP2+: remove uses of obsolete gpmc,device-nand
ARM: AM335X: EVM: fix pinmux documentation in devicetree
ARM: OMAP2+: N900: remove omapdss init for DT boot
ARM: dts: dra7xx-clocks: Correct mcasp2_ahclkx_mux bit-shift
ARM: dts: omap5: Add clocks to USB3 PHY node
ARM: OMAP2+: hwmod: fix missing braces in _init()
ARM: AM43xx: fix dpll init in bypass mode
ARM: OMAP3: hwmod data: Correct clock domains for USB modules
ARM: OMAP3: PM: remove access to PRM_VOLTCTRL register
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Updates the Ux500 (U8500) defconfig
- Selects PARTITION_ADVANCED for Ux500 and U300
- Configure in IIO sensor drivers for the Ux500
- Configure in the CW1200 WLAN chip for the Ux500
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Xe+n
-----END PGP SIGNATURE-----
Merge tag 'ux500-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
This is a patch set for some ST-Ericsson devices:
- Updates the Ux500 (U8500) defconfig
- Selects PARTITION_ADVANCED for Ux500 and U300
- Configure in IIO sensor drivers for the Ux500
- Configure in the CW1200 WLAN chip for the Ux500
* tag 'ux500-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: configure for CW1200 WLAN chip
ARM: ux500: configure in sensors
ARM: u300: u300_defconfig: Enable PARTITION_ADVANCED
ARM: ux500: u8500_defconfig: Enable PARTITION_ADVANCED
ARM: ux500: update defconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Correct renesas,groups in SDHI nodes of for r8a7790 (R-Car H2) based
Lager board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=ANme
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt5-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Fifth Round of Renesas ARM Based SoC DT Updates for v3.15
Correct renesas,groups in SDHI nodes of for r8a7790 (R-Car H2) based
Lager board.
* tag 'renesas-dt5-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: lager: correct renesas,gpios to renesas,groups in sd[02] pfc
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- A couple of dts changes for the fallout of imx-drm binding update
- Parent DI clocks to video PLL for better HDMI support
- PCIe interrupt mapping and GIC node fixes
- A series of edmqmx6 board fixes
- Other small and random fixes on imx5 and imx6 dts
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJTTOc9AAoJEFBXWFqHsHzO+S0H+wbYC7IJxwJ8YVRHChFAs6gV
vUP3MICQV49PUReGxhsc0iJmjnc8fJtXDR4wH7rmzlxQYdrYsnFYBk+yPXO6GhqW
Js4hkS4V/9CbGmL7v53eGhW9TyTq0yE+vWpKXZTyDoCbKKkfhKrtfRIjZgkdNBZD
3XAZ4zm3LFwca/GwLN2RSjJ6mdPX24pm+SDnblHqDvz/3KyfBQj2AYUYjRxElide
YcsUMcXU+/aJD1JTVdriw9lsP7sqJzsemj948j8XakBoU32A+DuoBuB0Dhm9Uv10
2qydt1R5pR9q2iX1/FYzZyTjs+KOW3ds8/Z36+MbWTytYS9TwzQ6bln0nOCUNhw=
=eymy
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 3.15:
- A couple of dts changes for the fallout of imx-drm binding update
- Parent DI clocks to video PLL for better HDMI support
- PCIe interrupt mapping and GIC node fixes
- A series of edmqmx6 board fixes
- Other small and random fixes on imx5 and imx6 dts
* tag 'imx-fixes-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: i.MX6: ipu_di_sel clocks can set parent rates
ARM: imx6q: clk: Parent DI clocks to video PLL via di_pre_sel
ARM: dts: imx: add required #clock-cells for fixed-clock
ARM: dts: vybrid: drop address and size cells from GIC node
ARM: dts: imx6sl-evk: Add an entry for MX6SL_PAD_ECSPI1_SS0__GPIO4_IO11
ARM: dts: imx53: fix apparent copy/paste error
ARM: dts: imx6q-gw5xxx: remove dead 'crtcs' property
ARM: dts: imx53-tx53: add IPU DI ports and endpoints
ARM: dts: imx6: edmqmx6: add second STMPE
ARM: dts: imx6: edmqmx6: USB H1 only supports host mode
ARM: dts: imx6: edmqmx6: Do not use the OTG switch as VBUS regulator
ARM: dts: imx6: edmqmx6: Fix usbotg id pin
ARM: dt: microsom: don't set bit 7 for ethernet mux settings
ARM: imx6q-clk: parent lvds_gate from lvds_sel
ARM: dts: imx: drop invalid size and address cells properties
ARM: dts: mx5: fix wrong stmpe-ts bindings
ARM: dts: imx53-m53evk: Fix memory region description
ARM: dts: imx53-qsb-common: Fix memory region description
ARM: dts: imx6: add PCIe interrupt mapping properties
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit a7cbe92cef ("ARM: tegra: remove tegra EMC scaling driver")
removed the only user of TEGRA_EMC_SCALING_ENABLE. Remove its Kconfig
entry too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Few things were out of order:
- removed ARCH_BCM2835 duplicate
- shuffled ARCH_BCM_5301X, ARCH_U8500 and ARCH_U300 around so to keep the
list sorted
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Signed-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In commit ddb902cc34 (ARM: centralize common multi-platform kconfig
options), CLKSRC_OF was removed from some platforms, but not added to
ARCH_MULTIPLATFORM. Fix this.
Reported-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I get a build warning because spear_clocksource_init() calls
clocksource_mmio_init(), but it doesn't have an __init annotation.
Fix that.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
hx4700 needs the same fix as in
9705e74671
"ARM: pxa: fix various compilation problems"
Fix build errors. Initial one is:
/linux/arch/arm/mach-pxa/include/mach/hx4700.h:18:32: error:
'PXA_NR_BUILTIN_GPIO' undeclared here (not in a function)
| #define HX4700_ASIC3_GPIO_BASE PXA_NR_BUILTIN_GPIO
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
dcscb_allcpus_mask is an array of size 2.
The index variable cluster has to be checked against this limit
before accessing the array.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
This patch fixes a bug introduced by:
2422365780 ("perf/x86/intel: Use rdmsrl_safe() when initializing RAPL PMU")
The rdmsrl_safe() function returns 0 on success.
The current code was failing to detect the RAPL PMU
on real hardware (missing /sys/devices/power) because
the return value of rdmsrl_safe() was misinterpreted.
Signed-off-by: Stephane Eranian <eranian@google.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Venkatesh Srinivas <venkateshs@google.com>
Cc: peterz@infradead.org
Cc: zheng.z.yan@intel.com
Link: http://lkml.kernel.org/r/20140423170418.GA12767@quad
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull ARM fixes from Russell King:
"Various fixes and post-merge window updates. Included here are:
- ensure Kconfig things which should be sorted remain sorted
- fix three big-endian bugs which crept in during the last merge
window
- add the renameat2 syscall
- fix big.LITTLE switcher initialisation checks
- fix kdump vmcore for LPAE kernels"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: add renameat2 syscall
ARM: keep arch/arm/Kconfig and arch/arm/mm/Kconfig select entries sorted
ARM: 8033/1: fix big endian __pv_phys_pfn_offset size related issue
ARM: 8032/1: bL_switcher: fix validation check before its activation
ARM: 8030/1: ARM : kdump : add arch_crash_save_vmcoreinfo
ARM: 8027/1: fix do_div() bug in big-endian systems
ARM: 8026/1: Fix emulation of multiply accumulate instructions
ARM: 8024/1: Keep DEBUG_UART_{PHYS,VIRT} entries sorted
I've noticed occasional random oopsing on my gateway
machine since I upgraded it to use device tree based
booting. As this machine has worked reliably before
that for a few years, pretty much the only difference
was narrowed down to the GPMC timings. Turns out that
for legacy based booting we are using bootloader timings
for GPMC for smsc911x. With device tree we are passing
the timings in the .dts file, and the device tree
timings are not quite suitable for LAN9920.
Enabling DEBUG in gpmc.c I noticed that the device tree
configured timings are different from the the known
working bootloader timings. So let's fix the timings to
match the bootloader timings when looked at the gpmc
dmesg output with DEBUG enabled.
The changes were done by multiplying the bootloader
tick values by six to get the nanosecond value for
device tree. This is not generic from the device point
of view as the calculations should be based on the device
timings. Anyways, further improvments can be done based
on the timings documentation for LAN9220. But let's first
get things to a known good working state.
Note that we still need to change the timings also for
sb-t35 also as it has two LAN9220 instances on GPMC and
we can currently include the generic timings only once.
Also note that any boards that have LAN9221 instead of
LAN9220 should be updated to use omap-gpmc-smsc9221.dtsi
instead of omap-gpmc-smsc911x.dtsi. The LAN9221 timings
are different from LAN9220 timings.
Cc: Christoph Fritz <chf.fritz@googlemail.com>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we have wrong GPMC timings we have for the cm-t and
sbc-t boards. This can cause occasional strange errors with at
least doing an rsync of large files or doing apt-get dist-upgrade.
Let's fix the issue in two phases. First let's simplify cm-t and
sbc-t to use the shared omap-gpmc-smsc911x.dtsi to avoid fixing
the issue in multiple places. Then we can fix the timings in
a single place with a follow-up patch.
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like the OTG pins are off by 2 and we get this:
pinctrl-single 48002030.pinmux: pin 480021a0.0 already requested by 49020000.serial; cannot claim for 480ab000.usb_otg_hs
pinctrl-single 48002030.pinmux: pin-184 (480ab000.usb_otg_hs) status -22
pinctrl-single 48002030.pinmux: could not request pin 184 (480021a0.0) from group pinmux_hsusb0_pins on device pinctrl-single
musb-omap2430 480ab000.usb_otg_hs: Error applying setting, reverse things back
That's probably because the TRM lists the values as
32-bit registers so every second needs 2 added to the
address. The OTG pin start range must start from
0x21a2, not 0x21a0.
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
At least the smc91x driver expects the device to be at 0x300
offset from bus base address. This does not work currently
for GPMC when booted in device tree mode as it attempts to
remap the the allocated GPMC partition to the address
configured by the device tree plus the device offset.
Note that this works just fine when booted with legacy mode.
Let's fix the issue by just ignoring any device specific
offset while remapping. And let's make sure the remap
address confirms to the GPMC 16MB minimum granularity
as listed in the TRM for GPMC_CONFIG7 BASEADDRESS bits.
Otherwise we can get something like this:
omap-gpmc 6e000000.gpmc: cannot remap GPMC CS 1 to 0x01000300
Cc: Pekon Gupta <pekon@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
68efd7d2fb("arm: dma-mapping: remove order parameter from
arm_iommu_create_mapping()") is causing kernel panic
because it wrongly sets the value of mapping->size:
Unable to handle kernel NULL pointer dereference at virtual
address 000000a0
pgd = e7a84000
[000000a0] *pgd=00000000
...
PC is at bitmap_clear+0x48/0xd0
LR is at __iommu_remove_mapping+0x130/0x164
Fix it by correcting mapping->size value.
Signed-off-by: Ritesh Harjani <ritesh.harjani@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
s/interrupts-names/interrupt-names/g
s/clocks-names/clock-names/g
Some of the binding files and device tree files get this wrong and the
kernel won't be able to pick it up. Fix them up now so that they don't
get widely used.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by : Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
* Fix the platform data support for the at91 adc driver.
* A couple of related follow up patches get the support working again
for at91sam9260 and at91sam9g45 as the earlier patch results in a device
name change.
* A default timer value in the at91 adc driver was bonkers. Make it sane.
* Fix incorrect reporting of the integration time for the cm32181 light sensor
* Fix a missing break in the ad2s1200 driver which would have give a false
error return.
* Make sure buffer scan mask queries from userspace return 0/1 rather than
a fairly random value depending on their implementation of test_bit
* Fix leak of the i2c client and a null pointer dereference in the cm36651
driver.
* Fix a build warning on avr32 for the mxs-lradc (not exactly a critical
combination - but the issue was real).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=HMr3
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.15a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First found of IIO fixes for the 3.15 cycle.
* Fix the platform data support for the at91 adc driver.
* A couple of related follow up patches get the support working again
for at91sam9260 and at91sam9g45 as the earlier patch results in a device
name change.
* A default timer value in the at91 adc driver was bonkers. Make it sane.
* Fix incorrect reporting of the integration time for the cm32181 light sensor
* Fix a missing break in the ad2s1200 driver which would have give a false
error return.
* Make sure buffer scan mask queries from userspace return 0/1 rather than
a fairly random value depending on their implementation of test_bit
* Fix leak of the i2c client and a null pointer dereference in the cm36651
driver.
* Fix a build warning on avr32 for the mxs-lradc (not exactly a critical
combination - but the issue was real).
Fix e26a9e00af 'ARM: Better
virt_to_page() handling' replaced __pv_phys_offset with
__pv_phys_pfn_offset. Also note that size of __pv_phys_offset
was quad but size of __pv_phys_pfn_offset is word. Instruction
that used to update __pv_phys_offset which address is in r6
had to update low word of __pv_phys_offset so it used #LOW_OFFSET
macro for store offset. Now when size of __pv_phys_pfn_offset is
word, no difference between little endian and big endian should
exist - i.e no offset should be used when __pv_phys_pfn_offset
is stored.
Note that for little endian image proposed change is noop,
since in little endian case #LOW_OFFSET is defined 0 anyway.
Reported-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The switcher should not depend on MAX_CLUSTER to determine ifit should
be activated or not. In a multiplatform kernel binary it is possible to
have dual-cluster and quad-cluster platforms configured in. In that case
MAX_CLUSTER which is a build time limit should be 4 and that shouldn't
prevent the switcher from working if the kernel is booted on a b.L
dual-cluster system.
In bL_switcher_halve_cpus() we already have a runtime validation check
to make sure we're dealing with only two clusters, so booting on a quad
cluster system will be caught and switcher activation aborted.
However, the b.L switcher must ensure the MCPM layer is initialized on
the booted hardware before doing anything. The mcpm_is_available()
function is added to that effect.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Abhilash Kesavan <kesavan.abhilash@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For vmcore generated by LPAE enabled kernel, user space
utility such as crash needs additional infomation to
parse.
So this patch add arch_crash_save_vmcoreinfo as what PAE enabled
i386 linux does.
Cc: <stable@vger.kernel.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Liu Hua <sdu.liu@huawei.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In big-endian systems, "%1" get the most significant part of the value, cause the instruction to get the wrong result.
When viewing ftrace record in big-endian ARM systems, we found that
the timestamp errors:
swapper-0 [001] 1325.970000: 0:120:R ==> [001] 16:120:R events/1
events/1-16 [001] 1325.970000: 16:120:S ==> [001] 0:120:R swapper
swapper-0 [000] 1325.1000000: 0:120:R + [000] 15:120:R events/0
swapper-0 [000] 1325.1000000: 0:120:R ==> [000] 15:120:R events/0
swapper-0 [000] 1326.030000: 0:120:R + [000] 1150:120:R sshd
swapper-0 [000] 1326.030000: 0:120:R ==> [000] 1150:120:R sshd
When viewed ftrace records, it will call the do_div(n, base) function, which achieved arch/arm/include/asm/div64.h in. When n = 10000000, base = 1000000, in do_div(n, base) will execute "umull %Q0, %R0, %1, %Q2".
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Cc: <stable@vger.kernel.org> # 2.6.20+
Signed-off-by: Alex Wu <wuquanming@huawei.com>
Signed-off-by: Xiangyu Lu <luxiangyu@huawei.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is a duplicated Kconfig entry for "kernel/power/Kconfig"
in menu "Power management options" and "CPU Power Management",
remove the one from menu "CPU Power Management" suggested by
Viresh.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This fixes commit 6290b53de0 (arm64: compat: Wire up new AArch32 syscalls)
which did not update __NR_compat_syscalls accordingly.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: <stable@vger.kernel.org> # 3.14+
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Pull x86 vdso fix from Peter Anvin:
"This is a single build fix for building with gold as opposed to GNU
ld. It got queued up separately and was expected to be pushed during
the merge window, but it got left behind"
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, vdso: Make the vdso linker script compatible with Gold
File-private locks have been merged into Linux for v3.15, and *now*
people are commenting that the name and macro definitions for the new
file-private locks suck.
...and I can't even disagree. The names and command macros do suck.
We're going to have to live with these for a long time, so it's
important that we be happy with the names before we're stuck with them.
The consensus on the lists so far is that they should be rechristened as
"open file description locks".
The name isn't a big deal for the kernel, but the command macros are not
visually distinct enough from the traditional POSIX lock macros. The
glibc and documentation folks are recommending that we change them to
look like F_OFD_{GETLK|SETLK|SETLKW}. That lessens the chance that a
programmer will typo one of the commands wrong, and also makes it easier
to spot this difference when reading code.
This patch makes the following changes that I think are necessary before
v3.15 ships:
1) rename the command macros to their new names. These end up in the uapi
headers and so are part of the external-facing API. It turns out that
glibc doesn't actually use the fcntl.h uapi header, but it's hard to
be sure that something else won't. Changing it now is safest.
2) make the the /proc/locks output display these as type "OFDLCK"
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Carlos O'Donell <carlos@redhat.com>
Cc: Stefan Metzmacher <metze@samba.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Frank Filz <ffilzlnx@mindspring.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Specify the 'clock-latency' property to avoid certain cpufreq governors
from refusing to work with the following error:
ondemand governor failed, too long transition latency of HW, fallback to performance governor
Reported-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If gpmc_cs_remap() fails we will get an error because we are calling
release_resource() on an uninitialized resource. Let's fix that by
checking the resource flags. And while at it, let's also make
gpmc_cs_delete_mem() use the res pointer that we already have to
avoid confusion.
Without this patch we can get the following error:
omap-gpmc 6e000000.gpmc: cannot remap GPMC CS 1 to 0x01000300
Unable to handle kernel NULL pointer dereference at virtual address 00000018
...
(gpmc_cs_free+0x94/0xc8)
(gpmc_probe_generic_child+0x178/0x1ec)
(gpmc_probe_dt+0x1bc/0x2cc)
(gpmc_probe+0x250/0x44c)
(platform_drv_probe+0x3c/0x6c)
(really_probe+0x74/0x208)
(driver_probe_device+0x34/0x50)
(bus_for_each_drv+0x60/0x8c)
(device_attach+0x80/0xa4)
(bus_probe_device+0x88/0xb0)
(device_add+0x320/0x450)
(of_platform_device_create_pdata+0x80/0x9c)
(of_platform_bus_create+0xd0/0x170)
(of_platform_bus_create+0x12c/0x170)
(of_platform_populate+0x60/0x98)
(pdata_quirks_init+0x30/0x48)
(customize_machine+0x20/0x48)
(do_one_initcall+0x2c/0x14c)
(do_basic_setup+0x98/0xd8)
(kernel_init_freeable+0x12c/0x1e0)
(kernel_init+0x8/0xf0)
(ret_from_fork+0x14/0x2c)
Code: e1a04000 e59f0070 eb195136 e5942010 (e5923018)
Cc: Pekon Gupta <pekon@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: tony Lindgren <tony@atomide.com>
The reverse case of this race (you must msync before read) is
well known. This is the not so common one.
It can be triggered only on systems which do a lot of task
switching and only at UML startup. If you are starting 200+ UMLs
~ 0.5% will always die without this fix.
Signed-off-by: Anton Ivanov <antivano@cisco.com>
[rw: minor whitespace fixes]
Signed-off-by: Richard Weinberger <richard@nod.at>
UML does not handle sigpipe. As a result when running it under
expect or redirecting the IO from the console to an external program
it will crash if the program stops or exits.
Signed-off-by: Anton Ivanov <antivano@cisco.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Inferring the mount hierarchy correctly from /proc/mounts is hard when MS_MOVE
may have been used, and the previous code did it wrongly. This change simplifies
the logic to only require that /dev/shm be _on_ tmpfs (which can be checked
trivially with statfs) rather than that it be a _mountpoint_ of tmpfs, since
there isn't a compelling reason to be that strict. We also now check for tmpfs
on whatever directory we ultimately use so that the user is better informed.
This change also moves the more standard TMPDIR environment variable check ahead
of the others.
Applies to 3.12.
Signed-off-by: Tristan Schmelcher <tschmelcher@google.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Pull x86 fix from Ingo Molnar:
"This fixes the preemption-count imbalance crash reported by Owen
Kibel"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Fix CMCI preemption bugs
BeagleBoard xM A/B has an inverted usb hub enable line vs the xM C
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
[tony@atomide.com: updated for missing bracket]
Signed-off-by: Tony Lindgren <tony@atomide.com>
A few OMAP hwmod and clock fixes for v3.15-rc. Probably the most useful
fix is the AM43xx DPLL patch.
Basic build, boot, and PM test results are here:
http://www.pwsan.com/omap/testlogs/prcm-fixes-a-v3.15-rc/20140411130021/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TOEq
-----END PGP SIGNATURE-----
Merge tag 'for-v3.15-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.15/fixes
OMAP hwmod and clock fixes for v3.15-rc
A few OMAP hwmod and clock fixes for v3.15-rc. Probably the most useful
fix is the AM43xx DPLL patch.
Basic build, boot, and PM test results are here:
http://www.pwsan.com/omap/testlogs/prcm-fixes-a-v3.15-rc/20140411130021/
Merge misc fixes from Andrew Morton:
"13 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
thp: close race between split and zap huge pages
mm: fix new kernel-doc warning in filemap.c
mm: fix CONFIG_DEBUG_VM_RB description
mm: use paravirt friendly ops for NUMA hinting ptes
mips: export flush_icache_range
mm/hugetlb.c: add cond_resched_lock() in return_unused_surplus_pages()
wait: explain the shadowing and type inconsistencies
Shiraz has moved
Documentation/vm/numa_memory_policy.txt: fix wrong document in numa_memory_policy.txt
powerpc/mm: fix ".__node_distance" undefined
kernel/watchdog.c:touch_softlockup_watchdog(): use raw_cpu_write()
init/Kconfig: move the trusted keyring config option to general setup
vmscan: reclaim_clean_pages_from_list() must use mod_zone_page_state()
The lkdtm module performs tests against executable memory ranges, so it
needs to flush the icache for proper behaviors. Other architectures
already export this, so do the same for MIPS.
[akpm@linux-foundation.org: relocate export sites]
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
shiraz.hashim@st.com email-id doesn't exist anymore as he has left the
company. Replace ST's id with shiraz.linux.kernel@gmail.com.
It also updates .mailmap file to fix address for 'git shortlog'.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit a70143 (drivers: phy: usb3/pipe3: Adapt pipe3 driver to Generic PHY
Framework) moved phy-omap-usb3 driver in drivers/usb/phy to drivers/phy and
also renamed the file to phy-ti-pipe3. It also renamed the config from
OMAP_USB3 to TI_PIPE3 in Kconfig. However the config name was not changed in
omap2plus_defconfig. Fixed it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In "ARM: dts: am33xx: correcting dt node unit address for usb", the
usb_ctrl_mod and cppi41dma nodes were updated with the correct register
addresses. However, the dts files that reference these nodes were not
updated, and those devices are no longer being enabled.
This patch corrects the references for the affected dts files.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove all remaining uses of gpmc,device-nand that have been added since
the property was removed by commit f40739faba ("ARM: dts: OMAP2+:
Simplify NAND support").
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Wrong documentation in pinmux description can be especially confusing.
Keep it proper.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Do not try to initialize display for DT boot, since omapdss
is now initialized via Device Tree. Without this patch the
display subsystem does not properly come up.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The correct bit is 24 for AHCLKX.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The USB3 PHY driver (ti-pipe3) was updated so that the relevant
clock phandles are expected in the DT node.
Provide the necessary clocks.
Reported-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most of the clock related dt-binding header files are located in
dt-bindings/clock folder. It would be good to keep all the similar
header files at a single location.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
CC: Rob Landley <rob@landley.net>
CC: Andrew Victor <linux@maxim.org.za>
CC: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Acked-by: Boris BREZILLON <b.brezillon.dev@gmail.com>
[nicolas.ferre@atmel.com: add new at91sam9261 & at91sam9rl]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The PD16 is the CS3 for SPI0 while not SPI1.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Commit 93ea02bb84 ("arch: Clean up asm/barrier.h implementations")
wired generic barrier.h for ARC, but failed to delete the existing file.
In 3.15, due to rcupdate.h updates, this causes a build breakage on ARC:
CC arch/arc/kernel/asm-offsets.s
In file included from include/linux/sched.h:45:0,
from arch/arc/kernel/asm-offsets.c:9:
include/linux/rculist.h: In function __list_add_rcu:
include/linux/rculist.h:54:2: error: implicit declaration of function smp_store_release [-Werror=implicit-function-declaration]
rcu_assign_pointer(list_next_rcu(prev), new);
^
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Host bridge drivers
- Fix OF interrupt mapping for DesignWare, R-Car, Tegra (Lucas Stach)
- Fix DesignWare iATU programming (Mohit Kumar)
Miscellaneous
- Fix powerpc NULL dereference from list_for_each_entry() update (Mike Qiu)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=VgYj
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.15-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"These are fixes for a powerpc NULL pointer dereference, an OF
interrupt mapping issue on some of the new host bridges, and a
DesignWare iATU issue.
Host bridge drivers
- Fix OF interrupt mapping for DesignWare, R-Car, Tegra (Lucas Stach)
- Fix DesignWare iATU programming (Mohit Kumar)
Miscellaneous
- Fix powerpc NULL dereference from list_for_each_entry() update (Mike Qiu)"
* tag 'pci-v3.15-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: tegra: Use new OF interrupt mapping when possible
PCI: rcar: Use new OF interrupt mapping when possible
PCI: designware: Use new OF interrupt mapping when possible
PCI: designware: Fix iATU programming for cfg1, io and mem viewport
PCI: designware: Fix comment for setting number of lanes
powerpc/PCI: Fix NULL dereference in sys_pciconfig_iobase() list traversal
CPUs which should support the RAPL counters according to
Family/Model/Stepping may still issue #GP when attempting to access
the RAPL MSRs. This may happen when Linux is running under KVM and
we are passing-through host F/M/S data, for example. Use rdmsrl_safe
to first access the RAPL_POWER_UNIT MSR; if this fails, do not
attempt to use this PMU.
Signed-off-by: Venkatesh Srinivas <venkateshs@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1394739386-22260-1-git-send-email-venkateshs@google.com
Cc: zheng.z.yan@intel.com
Cc: eranian@google.com
Cc: ak@linux.intel.com
Cc: linux-kernel@vger.kernel.org
[ The patch also silently fixes another bug: rapl_pmu_init() didn't handle the memory alloc failure case previously. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The current implementation of irq_set_affinity() refuses rightfully to
route an interrupt to an offline cpu.
But there is a special case, where this is actually desired. Some of
the ARM SoCs have per cpu timers which require setting the affinity
during cpu startup where the cpu is not yet in the online mask.
If we can't do that, then the local timer interrupt for the about to
become online cpu is routed to some random online cpu.
The developers of the affected machines tried to work around that
issue, but that results in a massive mess in that timer code.
We have a yet unused argument in the set_affinity callbacks of the irq
chips, which I added back then for a similar reason. It was never
required so it got not used. But I'm happy that I never removed it.
That allows us to implement a sane handling of the above scenario. So
the affected SoC drivers can add the required force handling to their
interrupt chip, switch the timer code to irq_force_affinity() and
things just work.
This does not affect any existing user of irq_set_affinity().
Tagged for stable to allow a simple fix of the affected SoC clock
event drivers.
Reported-and-tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>,
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>,
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org,
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20140416143315.717251504@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull parisc updates from Helge Deller:
"There are two major changes in this patchset:
The major fix is that the epoll_pwait() syscall for 32bit userspace
was not using the compat wrapper on a 64bit kernel.
Secondly we changed the value of SHMLBA from 4MB to PAGE_SIZE to
reflect that we can actually mmap to any multiple of PAGE_SIZE. The
only thing which needs care is that shared mmaps need to be mapped at
the same offset inside the 4MB cache window"
* 'parisc-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: fix epoll_pwait syscall on compat kernel
parisc: change value of SHMLBA from 0x00400000 to PAGE_SIZE
parisc: Replace __get_cpu_var uses for address calculation
- Fix completely broken 32-bit PV guests caused by x86 refactoring
32-bit thread_info.
- Only enable ticketlock slow path on Xen (not bare metal).
- Fix two bugs with PV guests not shutting down when requested.
- Fix a minor memory leak in xen-pciback error path.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQEcBAABAgAGBQJTT/hQAAoJEFxbo/MsZsTR6sMIAJs7mJXSqDQn3Z8O+TemRa53
p92ZomTNYALjUMglXcxJ2Zua6IsZMWdu7jcV1GoXC70V4YLmUs8KaBgZmI5ayUQy
bBpK+6WIAJyBkJdNH5fK3wggJ2UZjw0/twPNgd9gACwjUiYhx8iHN/hTGvu4qPBJ
MGAIlg6wdnGwRydi72uk9Am/xpebEdQy4DRD20vjwA/qUkT4uHVv/AA4hc4AK29w
ToK8qFSisgAlahcmq8/T4+OBFEKz78b9dQcdsGWyAk0ofWILfwD1l53xhzUin25s
JUVevWhhLCKRZBOq4Ykc5qyqnLff4m56rm/THQ6f0oRdJn/OR+SWOImda2Qqmvs=
=Gxpq
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.15-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fixes from David Vrabel:
"Xen regression and bug fixes for 3.15-rc1:
- fix completely broken 32-bit PV guests caused by x86 refactoring
32-bit thread_info.
- only enable ticketlock slow path on Xen (not bare metal)
- fix two bugs with PV guests not shutting down when requested
- fix a minor memory leak in xen-pciback error path"
* tag 'stable/for-linus-3.15-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/manage: Poweroff forcefully if user-space is not yet up.
xen/xenbus: Avoid synchronous wait on XenBus stalling shutdown/restart.
xen/spinlock: Don't enable them unconditionally.
xen-pciback: silence an unwanted debug printk
xen: fix memory leak in __xen_pcibk_add_pci_dev()
x86/xen: Fix 32-bit PV guests's usage of kernel_stack
Current kprobes in-kernel page fault handler doesn't
expect that its single-stepping can be interrupted by
an NMI handler which may cause a page fault(e.g. perf
with callback tracing).
In that case, the page-fault handled by kprobes and it
misunderstands the page-fault has been caused by the
single-stepping code and tries to recover IP address
to probed address.
But the truth is the page-fault has been caused by the
NMI handler, and do_page_fault failes to handle real
page fault because the IP address is modified and
causes Kernel BUGs like below.
----
[ 2264.726905] BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
[ 2264.727190] IP: [<ffffffff813c46e0>] copy_user_generic_string+0x0/0x40
To handle this correctly, I fixed the kprobes fault
handler to ensure the faulted ip address is its own
single-step buffer instead of checking current kprobe
state.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Sandeepa Prabhu <sandeepa.prabhu@linaro.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: fche@redhat.com
Cc: systemtap@sourceware.org
Link: http://lkml.kernel.org/r/20140417081644.26341.52351.stgit@ltc230.yrl.intra.hitachi.co.jp
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The following commit:
27f6c573e0 ("x86, CMCI: Add proper detection of end of CMCI storms")
Added two preemption bugs:
- machine_check_poll() does a get_cpu_var() without a matching
put_cpu_var(), which causes preemption imbalance and crashes upon
bootup.
- it does percpu ops without disabling preemption. Preemption is not
disabled due to the mistaken use of a raw spinlock.
To fix these bugs fix the imbalance and change
cmci_discover_lock to a regular spinlock.
Reported-by: Owen Kibel <qmewlo@gmail.com>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Chen, Gong <gong.chen@linux.intel.com>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Alexander Todorov <atodorov@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/n/tip-jtjptvgigpfkpvtQxpEk1at2@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
--
arch/x86/kernel/cpu/mcheck/mce.c | 4 +---
arch/x86/kernel/cpu/mcheck/mce_intel.c | 18 +++++++++---------
2 files changed, 10 insertions(+), 12 deletions(-)
In commit 4ca2c04085 ('ARM: orion5x:
Move to ID based window creation'), the mach-orion5x code was changed
to use the new mvebu-mbus API. However, in the process, a mistake was
made on the crypto SRAM window target ID: it should have been 0x9
(verified in the datasheet) and not 0x0.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: https://lkml.kernel.org/r/1397400006-4315-2-git-send-email-thomas.petazzoni@free-electrons.com
Fixes: 4ca2c04085 ('ARM: orion5x: Move to ID based window creation')
Cc: stable@vger.kernel.org # v3.12+
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull x86 fixes from Ingo Molnar:
"Various fixes:
- reboot regression fix
- build message spam fix
- GPU quirk fix
- 'make kvmconfig' fix
plus the wire-up of the renameat2() system call on i386"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Remove the PCI reboot method from the default chain
x86/build: Supress "Nothing to be done for ..." messages
x86/gpu: Fix sign extension issue in Intel graphics stolen memory quirks
x86/platform: Fix "make O=dir kvmconfig"
i386: Wire up the renameat2() syscall
Pull perf fixes from Ingo Molnar:
"Tooling fixes, plus a simple hardware-enablement patch for the Intel
RAPL PMU (energy use measurement) on Haswell CPUs, which I hope is
still fine at this stage"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Instead of redirecting flex output, use -o
perf tools: Fix double free in perf test 21 (code-reading.c)
perf stat: Initialize statistics correctly
perf bench: Set more defaults in the 'numa' suite
perf bench: Fix segfault at the end of an 'all' execution
perf bench: Update manpage to mention numa and futex
perf probe: Use dwarf_getcfi_elf() instead of dwarf_getcfi()
perf probe: Fix to handle errors in line_range searching
perf probe: Fix --line option behavior
perf tools: Pick up libdw without explicit LIBDW_DIR
MAINTAINERS: Change e-mail to kernel.org one
perf callchains: Disable unwind libraries when libelf isn't found
tools lib traceevent: Do not call warning() directly
tools lib traceevent: Print event name when show warning if possible
perf top: Fix documentation of invalid -s option
perf/x86: Enable DRAM RAPL support on Intel Haswell
- Fix a couple of barnsjukdomar on the Rockchip driver.
- Remove an idiotic debug print I happened to leave behind
in the Nomadik driver.
- Fixup the Qualcomm MSM interrupt handling code for the
TLMM v2.
- Three patches renaming the Broadcom Capri driver to
BCM28155. This has been falling between the chairs for
some time due to some cross-tree synchronization
misunderstandings, now I'm fed up with this and just
rename it in this -rc1 phase.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i5qY
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pincontrol fixes from Linus Walleij:
"A first set of pin control fixes for the v3.15 series:
- Fix a couple of barnsjukdomar on the Rockchip driver.
- Remove an idiotic debug print I happened to leave behind in the
Nomadik driver.
- Fixup the Qualcomm MSM interrupt handling code for the TLMM v2.
- Three patches renaming the Broadcom Capri driver to BCM28155. This
has been falling between the chairs for some time due to some
cross-tree synchronization misunderstandings, now I'm fed up with
this and just rename it in this -rc1 phase"
* tag 'pinctrl-v3.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: fix typo in bindings documentation
Update bcm_defconfig with new pinctrl CONFIG
pinctrl: Rename Broadcom Capri pinctrl driver
pinctrl: msm: Correct interrupt code for TLMM v2
pinctrl: nomadik: delete stray debug print
pinctrl: rockchip: handle first half of rk3188-bank0 correctly
pinctrl: rockchip: add return value to rockchip_set_mux
pinctrl: rockchip: fix offset of mux registers for rk3188
Pull s390 patches from Martin Schwidefsky:
"An update to the oops output with additional information about the
crash. The renameat2 system call is enabled. Two patches in regard
to the PTR_ERR_OR_ZERO cleanup. And a bunch of bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/sclp_cmd: replace PTR_RET with PTR_ERR_OR_ZERO
s390/sclp: replace PTR_RET with PTR_ERR_OR_ZERO
s390/sclp_vt220: Fix kernel panic due to early terminal input
s390/compat: fix typo
s390/uaccess: fix possible register corruption in strnlen_user_srst()
s390: add 31 bit warning message
s390: wire up sys_renameat2
s390: show_registers() should not map user space addresses to kernel symbols
s390/mm: print control registers and page table walk on crash
s390/smp: fix smp_stop_cpu() for !CONFIG_SMP
s390: fix control register update
April 2014 Itanium processor specification update:
http://www.intel.com/content/www/us/en/processors/itanium/itanium-specification-update.html
describes this erratum:
=========================================================================
237. Under a complex set of conditions, store to load forwarding for a
sub 8-byte load may complete incorrectly
Problem: A load instruction may complete incorrectly when a code sequence
using 4-byte or smaller load and store operations to the same address
is executed in combination with specific timing of all the following
concurrent conditions: store to load forwarding, alignment checking
enabled, a mis-predicted branch, and complex cache utilization activity.
Implication: The affected sub 8-byte instruction may complete
incorrectly resulting in unpredictable system behavior. There is an
extremely low probability of exposure due to the significant number of
complex microarchitectural concurrent conditions required to encounter
the erratum.
Workaround: Set PSR.ac = 0 to completely avoid the erratum. Disabling
Hyper-Threading will significantly reduce exposure to the conditions
that contribute to encountering the erratum.
Status: See the Summary Table of Changes for the affected steppings.
=========================================================================
[Table of changes essentially lists all models from McKinley to Tukwila]
The PSR.ac bit controls whether the processor will always generate
an unaligned reference trap (0x5a00) for a misaligned data access
(when PSR.ac=1) or if it will let the access succeed when running
on a cpu that implements logic to handle some unaligned accesses.
Way back in 2008 in commit b704882e70
[IA64] Rationalize kernel mode alignment checking
we made the decision to always enable strict checking. We were
already doing so in trap/interrupt context because the common
preamble code set this bit - but the rest of supervisor code
(and by inheritance user code) ran with PSR.ac=0.
We now reverse that decision and set PSR.ac=0 everywhere in the
kernel (also inherited by user processes). This will avoid the
erratum using the method described in the Itanium specification
update. Net effect for users is that the processor will handle
unaligned access when it can (typically with a tiny performance
bubble in the pipeline ... but much less invasive than taking a
trap and having the OS perform the access).
Signed-off-by: Tony Luck <tony.luck@intel.com>
Steve reported a reboot hang and bisected it back to this commit:
a4f1987e4c x86, reboot: Add EFI and CF9 reboot methods into the default list
He heroically tested all reboot methods and found the following:
reboot=t # triple fault ok
reboot=k # keyboard ctrl FAIL
reboot=b # BIOS ok
reboot=a # ACPI FAIL
reboot=e # EFI FAIL [system has no EFI]
reboot=p # PCI 0xcf9 FAIL
And I think it's pretty obvious that we should only try PCI 0xcf9 as a
last resort - if at all.
The other observation is that (on this box) we should never try
the PCI reboot method, but close with either the 'triple fault'
or the 'BIOS' (terminal!) reboot methods.
Thirdly, CF9_COND is a total misnomer - it should be something like
CF9_SAFE or CF9_CAREFUL, and 'CF9' should be 'CF9_FORCE' ...
So this patch fixes the worst problems:
- it orders the actual reboot logic to follow the reboot ordering
pattern - it was in a pretty random order before for no good
reason.
- it fixes the CF9 misnomers and uses BOOT_CF9_FORCE and
BOOT_CF9_SAFE flags to make the code more obvious.
- it tries the BIOS reboot method before the PCI reboot method.
(Since 'BIOS' is a terminal reboot method resulting in a hang
if it does not work, this is essentially equivalent to removing
the PCI reboot method from the default reboot chain.)
- just for the miraculous possibility of terminal (resulting
in hang) reboot methods of triple fault or BIOS returning
without having done their job, there's an ordering between
them as well.
Reported-and-bisected-and-tested-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Li Aubrey <aubrey.li@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Link: http://lkml.kernel.org/r/20140404064120.GB11877@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The git commit a945928ea2
('xen: Do not enable spinlocks before jump_label_init() has executed')
was added to deal with the jump machinery. Earlier the code
that turned on the jump label was only called by Xen specific
functions. But now that it had been moved to the initcall machinery
it gets called on Xen, KVM, and baremetal - ouch!. And the detection
machinery to only call it on Xen wasn't remembered in the heat
of merge window excitement.
This means that the slowpath is enabled on baremetal while it should
not be.
Reported-by: Waiman Long <waiman.long@hp.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
CC: stable@vger.kernel.org
CC: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Commit 198d208df4 ("x86: Keep
thread_info on thread stack in x86_32") made 32-bit kernels use
kernel_stack to point to thread_info. That change missed a couple of
updates needed by Xen's 32-bit PV guests:
1. kernel_stack needs to be initialized for secondary CPUs
2. GET_THREAD_INFO() now uses %fs register which may not be the
kernel's version when executing xen_iret().
With respect to the second issue, we don't need GET_THREAD_INFO()
anymore: we used it as an intermediate step to get to per_cpu xen_vcpu
and avoid referencing %fs. Now that we are going to use %fs anyway we
may as well go directly to xen_vcpu.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
The error emitted when mapping the pmu failed, wrongly mentions the sram.
Reported-by: Kent Borg <kentborg@borg.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The default behaviour of the uart-rx pins on the rk3188 is to be pulled up and
a lot of designs use diodes to even prevent them from being raised from the
outside.
Therefore change the rx-pin settings accordingly.
This also fixes a uart receive problem on mass production Radxa Rock boards.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
To obtain exact pixel clocks, allow the DI clock selectors to influence
the PLLs that they are derived from.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Route the video PLL to the display interface clocks via the di_pre_sel
and di_sel muxes by default.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Pull KVM fixes from Marcelo Tosatti:
- Fix for guest triggerable BUG_ON (CVE-2014-0155)
- CR4.SMAP support
- Spurious WARN_ON() fix
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: remove WARN_ON from get_kernel_ns()
KVM: Rename variable smep to cr4_smep
KVM: expose SMAP feature to guest
KVM: Disable SMAP for guests in EPT realmode and EPT unpaging mode
KVM: Add SMAP support when setting CR4
KVM: Remove SMAP bit from CR4_RESERVED_BITS
KVM: ioapic: try to recover if pending_eoi goes out of range
KVM: ioapic: fix assignment of ioapic->rtc_status.pending_eoi (CVE-2014-0155)
Fix typo of renesas,groups in the koeslch dt. The kernel has no
renesas,gpios but this should match renesas,groups.
Noticed thanks to similar fix for Lager by Rob Taylor and Ben Dooks.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.
address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.
address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
3bc955987f ("powerpc/PCI: Use list_for_each_entry() for bus traversal")
caused a NULL pointer dereference because the loop body set the iterator to
NULL:
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc000000000041d78
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP [c000000000041d78] .sys_pciconfig_iobase+0x68/0x1f0
LR [c000000000041e0c] .sys_pciconfig_iobase+0xfc/0x1f0
Call Trace:
[c0000003b4787db0] [c000000000041e0c] .sys_pciconfig_iobase+0xfc/0x1f0 (unreliable)
[c0000003b4787e30] [c000000000009ed8] syscall_exit+0x0/0x98
Fix it by using a temporary variable for the iterator.
[bhelgaas: changelog, drop tmp_bus initialization]
Fixes: 3bc955987f powerpc/PCI: Use list_for_each_entry() for bus traversal
Signed-off-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The emulation for single and double precision multiply accumulate
instructions correctly normalised any denormal values in the operand
registers, but failed to normalise the destination (accumulator)
register.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=70501
Signed-off-by: Jay Foad <jay.foad@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch sorts the entries for DEBUG_UART_{PHYS,VIRT}.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename variable smep to cr4_smep, which can better reflect the
meaning of the variable.
Signed-off-by: Feng Wu <feng.wu@intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
SMAP is disabled if CPU is in non-paging mode in hardware.
However KVM always uses paging mode to emulate guest non-paging
mode with TDP. To emulate this behavior, SMAP needs to be
manually disabled when guest switches to non-paging mode.
Signed-off-by: Feng Wu <feng.wu@intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch adds SMAP handling logic when setting CR4 for guests
Thanks a lot to Paolo Bonzini for his suggestion to use the branchless
way to detect SMAP violation.
Signed-off-by: Feng Wu <feng.wu@intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
According to the documentation the parent clock of
MSTP007 should be clks not clkp.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Allwinner reworked the PLL4 clock in sun7i; so we need to change the
compatible. Additionally, PLL8 is compatible with this new PLL4
implementation, so let's add a node for it as well.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
When we build an already built kernel again, arch/x86/syscalls/Makefile
and arch/x86/tools/Makefile emits "Nothing to be done for ..."
messages.
Here is the command log:
$ make defconfig
[ snip ]
$ make
[ snip ]
$ make
make[1]: Nothing to be done for `all'. <-----
make[1]: Nothing to be done for `relocs'. <-----
CHK include/config/kernel.release
CHK include/generated/uapi/linux/version.h
Besides not emitting those, "all" and "relocs" should be added to PHONY as well.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Peter Foley <pefoley2@pefoley.com>
Acked-by: Michal Marek <mmarek@suse.cz>
Link: http://lkml.kernel.org/r/1397093742-11144-1-git-send-email-yamada.m@jp.panasonic.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The CW1200 WLAN chip driver had been in the kernel for a while,
we only need to activate it for the Ux500 properly. The latter
require some elaborative work, but in the meantime, let's make
sure we atleast compile it in.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To be consistent with other Broadcom drivers, the Broadcom Capri pinctrl
driver and its related CONFIG option are renamed to bcm281xx.
This commit updates the defconfig that enables the pinctrl driver.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Reviewed-by: Matt Porter <mporter@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This enables the STMicroelectronics MEMS sensors for accelerometer,
gyroscope, magnetometer and pressure that are mounted on the Ux500
models.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since there are SD-card support in u300, it's reasonable to
support partitions for block devices as default.
While updating the defconfig, we rebase it towards Kconfig changes.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are both (e)MMC/SD-card support in ux500, thus it's reasonable to
support partitions for block devices as default.
While updating the defconfig, we rebase it towards Kconfig changes.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Have the KB(),MB(),GB() macros produce unsigned longs to avoid
unintended sign extension issues with the gen2 memory size
detection.
What happens is first the uint8_t returned by
read_pci_config_byte() gets promoted to an int which gets
multiplied by another int from the MB() macro, and finally the
result gets sign extended to size_t.
Although this shouldn't be a problem in practice as all affected
gen2 platforms are 32bit AFAIK, so size_t will be 32 bits.
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Suggested-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/1397382303-17525-1-git-send-email-ville.syrjala@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Running:
make O=dir x86_64_defconfig
make O=dir kvmconfig
the second command dirties the source tree with file ".config",
symlink "source" and objects in folder "scripts".
Fixed by using properly prefixed paths in the arch Makefile.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: Pekka Enberg <penberg@kernel.org>
Link: http://lkml.kernel.org/r/1397377568-8375-1-git-send-email-borneo.antonio@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
c7a507eea1
(ASoC: fsi: fixup SND_SOC_DAIFMT_CBx_CFx flags)
exchanged sound flags, but armadillo800eva flags needs IB_NF.
The recorded sound will be noise without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
e150828940
(ASoC: rcar: fixup SND_SOC_DAIFMT_CBx_CFx flags)
corrected SND_SOC_DAIFMT_CBx_CFx definition.
But then, Lager board was maintenanced other branch.
This patch correct SND_SOC_DAIFMT_CBx_CFx flag for lager
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Per bindings of fixed-clock, #clock-cells is a required property. Let's
add it for those fixed rate clocks.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.
address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
In case the bootloader has incorrectly configured the ALT mode of
MX6SL_PAD_ECSPI1_SS0 pad, we end up with the following probe error:
m25p80 spi0.0: found mr25h256, expected m25p32
m25p80 spi0.0: mr25h256 (32 Kbytes)
In order to avoid this issue, add an entry for MX6SL_PAD_ECSPI1_SS0 pad, so
that kernel configures the ECSPI chip select as GPIO functionality, which
results in correct SPI NOR probe.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The 'remote-endpoint' property should point back to ipu_di1_lvds1
rather than ipu_di0_lvds0.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Since commit (655b43c staging: imx-drm-core: Use OF graph to find
components and connections between encoder and crtcs), 'crtcs' becomes a
dead property. Remove it.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
With the recent imx-drm device tree binding changes, we need to add IPU
DI ports and endpoints for adapting.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
GPIO7_12 switches the D+/D- USB lines on and off. When we use this as
VBUS regulator it means that USB device mode can never work as VBUS is
never turned on in Device mode.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Bit 6,7 are marked as reserved for the ethernet RGMII pins, so avoid
setting these bits.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Allows fror proper refcounting of the parent clocks
when enabling the clock output on CLK1/2 pads.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Richard Zhu <r65037@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Those two properties should have been set to zero, which
is the same as not specifying them.
Having address-cells set to 1 causes OF interrupt
mapping routines to add 1 to the interrupt-cells
property and as result fail because all calculations
are off by one.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fix bindings for STMPE touchscreen controller to match the documented
bindings and the actual bindings used by the driver.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
On m53evk there are two DRAM chip selects:
CS0 at 0x70000000
CS1 at 0xb0000000
Each bank has a 512MB DRAM, giving a total of 1GB of system DRAM.
Fix the memory layout to describe the hardware appropriately.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
On mx53qsb there are two DRAM chip selects:
CS0 at 0x70000000
CS1 at 0xb0000000
Each bank has a 512MB DRAM, giving a total of 1GB of system DRAM.
Fix the memory layout to describe the hardware appropriately.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
As defined by the common PCI bindings.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This bug was detected with the libio-epoll-perl debian package where the
test case IO-Ppoll-compat.t failed.
Signed-off-by: Helge Deller <deller@gmx.de>
CC: stable@kernel.org # 3.0+
On parisc, SHMLBA was defined to 0x00400000 (4MB) to reflect that we need to
take care of our caches for shared mappings. But actually, we can map a file at
any multiple address of PAGE_SIZE, so let us correct that now with a value of
PAGE_SIZE for SHMLBA. Instead we now take care of this cache colouring via the
constant SHM_COLOUR while we map shared pages.
Signed-off-by: Helge Deller <deller@gmx.de>
CC: Jeroen Roovers <jer@gentoo.org>
CC: John David Anglin <dave.anglin@bell.net>
CC: Carlos O'Donell <carlos@systemhalted.org>
Cc: stable@kernel.org [3.13+]
Commit 8f619b5429 ("powerpc/ppc64: Do not turn AIL (reloc-on
interrupts) too early") added code to set the AIL bit in the LPCR
without checking whether the kernel is running in hypervisor mode. The
result is that when the kernel is running as a guest (i.e., under
PowerKVM or PowerVM), the processor takes a privileged instruction
interrupt at that point, causing a panic. The visible result is that
the kernel hangs after printing "returning from prom_init".
This fixes it by checking for hypervisor mode being available before
setting LPCR. If we are not in hypervisor mode, we enable relocation-on
interrupts later in pSeries_setup_arch using the H_SET_MODE hcall.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iEYEABECAAYFAlNFtEkACgkQuseO5dulBZVcPwCdFWY81hKqQaKHaSPFh9m+n1lt
yY0An2VZZGrFSkj162POFy1P2sPpGw5p
=LRFZ
-----END PGP SIGNATURE-----
Merge tag 'llvmlinux-for-v3.15' of git://git.linuxfoundation.org/llvmlinux/kernel
Pull llvm patches from Behan Webster:
"These are some initial updates to support compiling the kernel with
clang.
These patches have been through the proper reviews to the best of my
ability, and have been soaking in linux-next for a few weeks. These
patches by themselves still do not completely allow clang to be used
with the kernel code, but lay the foundation for other patches which
are still under review.
Several other of the LLVMLinux patches have been already added via
maintainer trees"
* tag 'llvmlinux-for-v3.15' of git://git.linuxfoundation.org/llvmlinux/kernel:
x86: LLVMLinux: Fix "incomplete type const struct x86cpu_device_id"
x86 kbuild: LLVMLinux: More cc-options added for clang
x86, acpi: LLVMLinux: Remove nested functions from Thinkpad ACPI
LLVMLinux: Add support for clang to compiler.h and new compiler-clang.h
LLVMLinux: Remove warning about returning an uninitialized variable
kbuild: LLVMLinux: Fix LINUX_COMPILER definition script for compilation with clang
Documentation: LLVMLinux: Update Documentation/dontdiff
kbuild: LLVMLinux: Adapt warnings for compilation with clang
kbuild: LLVMLinux: Add Kbuild support for building kernel with Clang
Pull vfs updates from Al Viro:
"The first vfs pile, with deep apologies for being very late in this
window.
Assorted cleanups and fixes, plus a large preparatory part of iov_iter
work. There's a lot more of that, but it'll probably go into the next
merge window - it *does* shape up nicely, removes a lot of
boilerplate, gets rid of locking inconsistencie between aio_write and
splice_write and I hope to get Kent's direct-io rewrite merged into
the same queue, but some of the stuff after this point is having
(mostly trivial) conflicts with the things already merged into
mainline and with some I want more testing.
This one passes LTP and xfstests without regressions, in addition to
usual beating. BTW, readahead02 in ltp syscalls testsuite has started
giving failures since "mm/readahead.c: fix readahead failure for
memoryless NUMA nodes and limit readahead pages" - might be a false
positive, might be a real regression..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
missing bits of "splice: fix racy pipe->buffers uses"
cifs: fix the race in cifs_writev()
ceph_sync_{,direct_}write: fix an oops on ceph_osdc_new_request() failure
kill generic_file_buffered_write()
ocfs2_file_aio_write(): switch to generic_perform_write()
ceph_aio_write(): switch to generic_perform_write()
xfs_file_buffered_aio_write(): switch to generic_perform_write()
export generic_perform_write(), start getting rid of generic_file_buffer_write()
generic_file_direct_write(): get rid of ppos argument
btrfs_file_aio_write(): get rid of ppos
kill the 5th argument of generic_file_buffered_write()
kill the 4th argument of __generic_file_aio_write()
lustre: don't open-code kernel_recvmsg()
ocfs2: don't open-code kernel_recvmsg()
drbd: don't open-code kernel_recvmsg()
constify blk_rq_map_user_iov() and friends
lustre: switch to kernel_sendmsg()
ocfs2: don't open-code kernel_sendmsg()
take iov_iter stuff to mm/iov_iter.c
process_vm_access: tidy up a bit
...
Pull audit updates from Eric Paris.
* git://git.infradead.org/users/eparis/audit: (28 commits)
AUDIT: make audit_is_compat depend on CONFIG_AUDIT_COMPAT_GENERIC
audit: renumber AUDIT_FEATURE_CHANGE into the 1300 range
audit: do not cast audit_rule_data pointers pointlesly
AUDIT: Allow login in non-init namespaces
audit: define audit_is_compat in kernel internal header
kernel: Use RCU_INIT_POINTER(x, NULL) in audit.c
sched: declare pid_alive as inline
audit: use uapi/linux/audit.h for AUDIT_ARCH declarations
syscall_get_arch: remove useless function arguments
audit: remove stray newline from audit_log_execve_info() audit_panic() call
audit: remove stray newlines from audit_log_lost messages
audit: include subject in login records
audit: remove superfluous new- prefix in AUDIT_LOGIN messages
audit: allow user processes to log from another PID namespace
audit: anchor all pid references in the initial pid namespace
audit: convert PPIDs to the inital PID namespace.
pid: get pid_t ppid of task in init_pid_ns
audit: rename the misleading audit_get_context() to audit_take_context()
audit: Add generic compat syscall support
audit: Add CONFIG_HAVE_ARCH_AUDITSYSCALL
...
In v3.2 the Analog Devices ADT75 temperature sensor driver was removed
as an IIO driver and support for it was added to the LM75 HWMON driver.
But it was apparently overlooked to rename one reference to CONFIG_ADT75
to CONFIG_SENSORS_LM75. Do so now. Use the IS_ENABLED() macro, while
we're at it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
In v3.2 the Analog Devices AD7314 temperature sensor driver was removed
as an IIO driver and added as a HWMON driver. But it was apparently
overlooked to rename two references to CONFIG_AD7314 to
CONFIG_SENSORS_AD7314. Do so now. Use the IS_ENABLED() macro, while
we're at it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
In v3.2 the Analog Devices ad2s1200/ad2s1205 driver was renamed from
ad2s120x to ad2s1200. But it apparently forgot to rename the references
to this driver in the BF537-STAMP code. Rename these now, and use the
IS_ENABLED() macro, while we're at it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
There's a (rather subtle) typo in "CONFIG_SND_SOC_ADV80X_MODULE". Fix it
once and for all by using IS_ENABLED(), which is designed to avoid
issues like this.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
drop unused head file
change pinmux request/free macro for backward compatiblity
add function declaration
Signed-off-by: Steven Miao <realmz6@gmail.com>
- Fix for a recently introduced CPU hotplug regression in ARM KVM
from Ming Lei.
- Fixes for breakage in the at32ap, loongson2_cpufreq, and unicore32
cpufreq drivers introduced during the 3.14 cycle (-stable material)
from Chen Gang and Viresh Kumar.
- New powernv cpufreq driver from Vaidyanathan Srinivasan, with bits
from Gautham R Shenoy and Srivatsa S Bhat.
- Exynos cpufreq driver fix preventing it from being included into
multiplatform builds that aren't supported by it from Sachin Kamat.
- cpufreq cleanups related to the usage of the driver_data field in
struct cpufreq_frequency_table from Viresh Kumar.
- cpufreq ppc driver cleanup from Sachin Kamat.
- Intel BayTrail support for intel_idle and ACPI idle from Len Brown.
- Intel CPU model 54 (Atom N2000 series) support for intel_idle from
Jan Kiszka.
- intel_idle fix for Intel Ivy Town residency targets from Len Brown.
- turbostat updates (Intel Broadwell support and output cleanups)
from Len Brown.
- New cpuidle sysfs attribute for exporting C-states' target residency
information to user space from Daniel Lezcano.
- New kernel command line argument to prevent power domains enabled
by the bootloader from being turned off even if they are not in use
(for diagnostics purposes) from Tushar Behera.
- Fixes for wakeup sysfs attributes documentation from Geert Uytterhoeven.
- New ACPI video blacklist entry for ThinkPad Helix from Stephen Chandler
Paul.
- Assorted ACPI cleanups and a Kconfig help update from Jonghwan Choi,
Zhihui Zhang, Hanjun Guo.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=hGKg
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.15-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management fixes and updates from Rafael Wysocki:
"This is PM and ACPI material that has emerged over the last two weeks
and one fix for a CPU hotplug regression introduced by the recent CPU
hotplug notifiers registration series.
Included are intel_idle and turbostat updates from Len Brown (these
have been in linux-next for quite some time), a new cpufreq driver for
powernv (that might spend some more time in linux-next, but BenH was
asking me so nicely to push it for 3.15 that I couldn't resist), some
cpufreq fixes and cleanups (including fixes for some silly breakage in
a couple of cpufreq drivers introduced during the 3.14 cycle),
assorted ACPI cleanups, wakeup framework documentation fixes, a new
sysfs attribute for cpuidle and a new command line argument for power
domains diagnostics.
Specifics:
- Fix for a recently introduced CPU hotplug regression in ARM KVM
from Ming Lei.
- Fixes for breakage in the at32ap, loongson2_cpufreq, and unicore32
cpufreq drivers introduced during the 3.14 cycle (-stable material)
from Chen Gang and Viresh Kumar.
- New powernv cpufreq driver from Vaidyanathan Srinivasan, with bits
from Gautham R Shenoy and Srivatsa S Bhat.
- Exynos cpufreq driver fix preventing it from being included into
multiplatform builds that aren't supported by it from Sachin Kamat.
- cpufreq cleanups related to the usage of the driver_data field in
struct cpufreq_frequency_table from Viresh Kumar.
- cpufreq ppc driver cleanup from Sachin Kamat.
- Intel BayTrail support for intel_idle and ACPI idle from Len Brown.
- Intel CPU model 54 (Atom N2000 series) support for intel_idle from
Jan Kiszka.
- intel_idle fix for Intel Ivy Town residency targets from Len Brown.
- turbostat updates (Intel Broadwell support and output cleanups)
from Len Brown.
- New cpuidle sysfs attribute for exporting C-states' target
residency information to user space from Daniel Lezcano.
- New kernel command line argument to prevent power domains enabled
by the bootloader from being turned off even if they are not in use
(for diagnostics purposes) from Tushar Behera.
- Fixes for wakeup sysfs attributes documentation from Geert
Uytterhoeven.
- New ACPI video blacklist entry for ThinkPad Helix from Stephen
Chandler Paul.
- Assorted ACPI cleanups and a Kconfig help update from Jonghwan
Choi, Zhihui Zhang, Hanjun Guo"
* tag 'pm+acpi-3.15-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (28 commits)
ACPI: Update the ACPI spec information in Kconfig
arm, kvm: fix double lock on cpu_add_remove_lock
cpuidle: sysfs: Export target residency information
cpufreq: ppc: Remove duplicate inclusion of fsl_soc.h
cpufreq: create another field .flags in cpufreq_frequency_table
cpufreq: use kzalloc() to allocate memory for cpufreq_frequency_table
cpufreq: don't print value of .driver_data from core
cpufreq: ia64: don't set .driver_data to index
cpufreq: powernv: Select CPUFreq related Kconfig options for powernv
cpufreq: powernv: Use cpufreq_frequency_table.driver_data to store pstate ids
cpufreq: powernv: cpufreq driver for powernv platform
cpufreq: at32ap: don't declare local variable as static
cpufreq: loongson2_cpufreq: don't declare local variable as static
cpufreq: unicore32: fix typo issue for 'clk'
cpufreq: exynos: Disable on multiplatform build
PM / wakeup: Correct presence vs. emptiness of wakeup_* attributes
PM / domains: Add pd_ignore_unused to keep power domains enabled
ACPI / dock: Drop dock_device_ids[] table
ACPI / video: Favor native backlight interface for ThinkPad Helix
ACPI / thermal: Fix wrong variable usage in debug statement
...
Pullx86 core platform updates from Peter Anvin:
"This is the x86/platform branch with the objectionable IOSF patches
removed.
What is left is proper memory handling for Intel GPUs, and a change to
the Calgary IOMMU code which will be required to make kexec work
sanely on those platforms after some upcoming kexec changes"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, calgary: Use 8M TCE table size by default
x86/gpu: Print the Intel graphics stolen memory range
x86/gpu: Add Intel graphics stolen memory quirk for gen2 platforms
x86/gpu: Add vfunc for Intel graphics stolen memory base address
Pull x86 fixes from Peter Anvin:
"This is a collection of minor fixes for x86, plus the IRET information
leak fix (forbid the use of 16-bit segments in 64-bit mode)"
NOTE! We may have to relax the "forbid the use of 16-bit segments in
64-bit mode" part, since there may be people who still run and depend on
16-bit Windows binaries under Wine.
But I'm taking this in the current unconditional form for now to see who
(if anybody) screams bloody murder. Maybe nobody cares. And maybe
we'll have to update it with some kind of runtime enablement (like our
vm.mmap_min_addr tunable that people who run dosemu/qemu/wine already
need to tweak).
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86-64, modify_ldt: Ban 16-bit segments on 64-bit kernels
efi: Pass correct file handle to efi_file_{read,close}
x86/efi: Correct EFI boot stub use of code32_start
x86/efi: Fix boot failure with EFI stub
x86/platform/hyperv: Handle VMBUS driver being a module
x86/apic: Reinstate error IRQ Pentium erratum 3AP workaround
x86, CMCI: Add proper detection of end of CMCI storms
Pull second set of ARM changes from Russell King:
"This is the remainder of the ARM changes for this merge window.
Included in this request are:
- fixes for kprobes for big-endian support
- fix tracing in soft_restart
- avoid phys address overflow in kdump code
- fix reporting of read-only pmd bits in kernel page table dump
- remove unnecessary (and possibly buggy) call to outer_flush_all()
- fix a three sparse warnings (missing header file for function
prototypes)
- fix pj4 crashing single zImage (thanks to arm-soc merging changes
which enables this with knowledge that the corresponding fix had
not even been submitted for my tree before the merge window opened)
- vfp macro cleanups
- dump register state on undefined instruction userspace faults when
debugging"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
Dump the registers on undefined instruction userspace faults
ARM: 8018/1: Add {inc,dec}_preempt_count asm macros
ARM: 8017/1: Move asm macro get_thread_info to asm/assembler.h
ARM: 8016/1: Check cpu id in pj4_cp0_init.
ARM: 8015/1: Add cpu_is_pj4 to distinguish PJ4 because it has some differences with V7
ARM: add missing system_misc.h include to process.c
ARM: 8009/1: dcscb.c: remove call to outer_flush_all()
ARM: 8014/1: mm: fix reporting of read-only PMD bits
ARM: 8012/1: kdump: Avoid overflow when converting pfn to physaddr
ARM: 8010/1: avoid tracers in soft_restart
ARM: kprobes-test: Workaround GAS .align bug
ARM: kprobes-test: use <asm/opcodes.h> for Thumb instruction building
ARM: kprobes-test: use <asm/opcodes.h> for ARM instruction building
ARM: kprobes-test: use <asm/opcodes.h> for instruction accesses
ARM: probes: fix instruction fetch order with <asm/opcodes.h>
- Use asm-generic/io.h and fix intc/timer code
- Clean platform handling
- Enable some syscalls
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iEYEABECAAYFAlNHiDIACgkQykllyylKDCHbLgCggWXqrfHFULZqlTUfAV2krfsx
q44AoJ5sI0rBHEtXnL8Clo5+4vpftv0G
=CRLR
-----END PGP SIGNATURE-----
Merge tag 'microblaze-3.15-rc1' of git://git.monstr.eu/linux-2.6-microblaze
Pull Microblaze updates from Michal Simek:
- use asm-generic/io.h and fix intc/timer code
- clean platform handling
- enable some syscalls
* tag 'microblaze-3.15-rc1' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Use asm-generic/io.h
microblaze: Remove platform folder
microblaze: Remove generic platform
microblaze: Sort Kconfig options
microblaze: Move DTS file to common location at boot/dts folder
microblaze: Fix compilation failure because of release_thread
microblaze: Fix sparse warning because of missing cpu.h header
microblaze: Make timer driver endian aware
microblaze: Make intc driver endian aware
microblaze: Wire-up new system calls sched_setattr/getattr
microblaze: Wire-up preadv/pwritev in syscall table
microblaze: Enable pselect6 syscall
microblaze: Drop architecture-specific declaration of early_printk
microblaze: Rename global function heartbeat()
Bug was introduced by commit 'f92d959: ARM: OMAP2+: hwmod:
Extract no-idle and no-reset info from DT'
There were 2 versions of the patch posted which resulted in the above
commit. While v1 [1] had the bug, v2 [2] had it fixed.
However v1 apparently seemed to have been pulled in by mistake
introducing the bug.
Given of_find_property() does return NULL when the node passed is
NULL, it did not introduce any functional issues as such, just the
fact that the second if check was executed unnecessarily.
[1] https://www.mail-archive.com/linux-omap@vger.kernel.org/msg94220.html
[2] http://www.spinics.net/lists/linux-omap/msg98490.html
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Fixes: f92d9597f7 ("ARM: OMAP2+: hwmod: Extract no-idle and no-reset info from DT")
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On AM43xx, if a PLL is in bypass at kernel init, the code in
omap2_get_dpll_rate() will not realize this and will try to calculate
the clock rate using the multiplier and the divider, resulting in
errors.
omap2_init_dpll_parent() has similar issue.
Add the missing soc_is_am43xx() check to make the code work on AM43xx.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Sathya Prakash M R <sathyap@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP3 doesn't contain "l3_init_clkdm" clock domain. Use the
proper clock domains for USB Host and USB TLL modules.
Gets rid of the following warnings during boot
omap_hwmod: usb_host_hs: could not associate to clkdm l3_init_clkdm
omap_hwmod: usb_tll_hs: could not associate to clkdm l3_init_clkdm
Reported-by: Nishanth Menon <nm@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Fixes: de231388cb ("ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3")
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: Partha Basak <parthab@india.ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The IRET instruction, when returning to a 16-bit segment, only
restores the bottom 16 bits of the user space stack pointer. We have
a software workaround for that ("espfix") for the 32-bit kernel, but
it relies on a nonzero stack segment base which is not available in
32-bit mode.
Since 16-bit support is somewhat crippled anyway on a 64-bit kernel
(no V86 mode), and most (if not quite all) 64-bit processors support
virtualization for the users who really need it, simply reject
attempts at creating a 16-bit segment when running on top of a 64-bit
kernel.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/n/tip-kicdm89kzw9lldryb1br9od0@git.kernel.org
Cc: <stable@vger.kernel.org>
The only user of Kconfig symbol IP_CHECKSUM_L1 got removed in v2.6.33,
with commit ddf9ddacef ("Blackfin: convert
to generic checksum code"). We can remove the Kconfig entry for this
unused symbol now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
The Kconfig symbol GENERIC_GPIO was removed in v3.10. Nothing cares
about it anymore. It popped up somehow in v3.13, so it can be removed
again.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
There is nothing special in that blackfin code. Use the core
implementation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Steven Miao <realmz6@gmail.com>
Cc: bfin <adi-buildroot-devel@lists.sourceforge.net>
The whole point of the out-of-line strnlen_user_srst() function was to
avoid corruption of register 0 due to register asm assignment.
However 'somebody' :) forgot to remove the update_primary_asce() function
call, which may clobber register 0 contents.
So let's remove that call and also move the size check to the calling
function.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Actually this also enable sys_setattr and sys_getattr, since I forgot to
increase NR_syscalls when adding those syscalls.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It doesn't make sense to map user space addresses to kernel symbols when
show_registers() prints a user space psw. So just skip the translation part
if a user space psw is handled.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
firmware was reading random values from the stack because we were
passing a pointer to the wrong object type.
* Kernel corruption has been reported when booting with the EFI boot
stub which was tracked down to setting a bogus value for
bp->hdr.code32_start, resulting in corruption during relocation.
* Olivier Martin reported that the wrong file handles were being passed
to efi_file_(read|close), which works for x86 by luck due to the way
that the FAT driver is implemented, but doesn't work on ARM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rovT
-----END PGP SIGNATURE-----
Merge tag 'efi-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/urgent
Pull EFI fixes from Matt Fleming:
"* Fix EFI boot regression introduced during the merge window where the
firmware was reading random values from the stack because we were
passing a pointer to the wrong object type.
* Kernel corruption has been reported when booting with the EFI boot
stub which was tracked down to setting a bogus value for
bp->hdr.code32_start, resulting in corruption during relocation.
* Olivier Martin reported that the wrong file handles were being passed
to efi_file_(read|close), which works for x86 by luck due to the way
that the FAT driver is implemented, but doesn't work on ARM."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
New kexec-tools wants to pass kdump kernel needed memmap via E820
directly, instead of memmap=exactmap. This makes saved_max_pfn not
be passed down to 2nd kernel. To keep 1st kernel and 2nd kernel using
the same TCE table size, Muli suggest to hard code the size to max (8M).
We can't get rid of saved_max_pfn this time, for backward compatibility
with old first kernel and new second kernel. However new first kernel
and old second kernel can not work unfortunately.
v2->v1:
- retain saved_max_pfn so new 2nd kernel can work with old 1st kernel
from Vivek
Signed-off-by: WANG Chao <chaowang@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Muli Ben-Yehuda <mulix@mulix.org>
Acked-by: Jon Mason <jdmason@kudzu.us>
Link: http://lkml.kernel.org/r/1394463120-26999-1-git-send-email-chaowang@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
We're currently passing the file handle for the root file system to
efi_file_read() and efi_file_close(), instead of the file handle for the
file we wish to read/close.
While this has worked up until now, it seems that it has only been by
pure luck. Olivier explains,
"The issue is the UEFI Fat driver might return the same function for
'fh->read()' and 'h->read()'. While in our case it does not work with
a different implementation of EFI_SIMPLE_FILE_SYSTEM_PROTOCOL. In our
case, we return a different pointer when reading a directory and
reading a file."
Fixing this actually clears up the two functions because we can drop one
of the arguments, and instead only pass a file 'handle' argument.
Reported-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Olivier Martin <olivier.martin@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
code32_start should point at the start of the protected mode code, and
*not* at the beginning of the bzImage. This is much easier to do in
assembly so document that callers of make_boot_params() need to fill out
code32_start.
The fallout from this bug is that we would end up relocating the image
but copying the image at some offset, resulting in what appeared to be
memory corruption.
Reported-by: Thomas Bächler <thomas@archlinux.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
commit 54b52d8726 ("x86/efi: Build our own EFI services pointer
table") introduced a regression because the 64-bit file_size()
implementation passed a pointer to a 32-bit data object, instead of a
pointer to a 64-bit object.
Because the firmware treats the object as 64-bits regardless it was
reading random values from the stack for the upper 32-bits.
This resulted in people being unable to boot their machines, after
seeing the following error messages,
Failed to get file info size
Failed to alloc highmem for files
Reported-by: Dzmitry Sledneu <dzmitry.sledneu@gmail.com>
Reported-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
There is a solitary write to this register every wakeup from off-mode,
which isn't doing anything, so remove it.
Also note that modifying this register trashes any attempted
voltage scaling configuration and the change probably should
never have gotten merged in the first place.
Cc: Nishanth Menon <nm@ti.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[tony@atomide.com: updated comments to describe regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull slave-dmaengine updates from Vinod Koul:
- New driver for Qcom bam dma
- New driver for RCAR peri-peri
- New driver for FSL eDMA
- Various odd fixes and updates thru the subsystem
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (29 commits)
dmaengine: add Qualcomm BAM dma driver
shdma: add R-Car Audio DMAC peri peri driver
dmaengine: sirf: enable generic dt binding for dma channels
dma: omap-dma: Implement device_slave_caps callback
dmaengine: qcom_bam_dma: Add device tree binding
dma: dw: Add suspend and resume handling for PCI mode DW_DMAC.
dma: dw: allocate memory in two stages in probe
Add new line to test result strings produced in verbose mode
dmaengine: pch_dma: use tasklet_kill in teardown
dmaengine: at_hdmac: use tasklet_kill in teardown
dma: cppi41: start tear down only if channel is busy
usb: musb: musb_cppi41: Dont reprogram DMA if tear down is initiated
dmaengine: s3c24xx-dma: make phy->irq signed for error handling
dma: imx-dma: Add missing module owner field
dma: imx-dma: Replace printk with dev_*
dma: fsl-edma: fix static checker warning of NULL dereference
dma: Remove comment about embedding dma_slave_config into custom structs
dma: mmp_tdma: move to generic device tree binding
dma: mmp_pdma: add IRQF_SHARED when request irq
dma: edma: Fix memory leak in edma_prep_dma_cyclic()
...
sysmem structure initialization in xt2000 platform_init is identical to
the one done in init_arch just before the call to platform_init.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Protect more options for x86 with cc-option so that we don't get errors when
using clang instead of gcc. Add more or different options when using clang as
well. Also need to enforce that SSE is off for clang and the stack is 8-byte
aligned.
Signed-off-by: Jan-Simon Möller <dl9pf@gmx.de>
Signed-off-by: Behan Webster <behanw@converseincode.com>
Signed-off-by: Mark Charlebois <charlebm@gmail.com>
Pull i2c updates from Wolfram Sang:
"Here is the pull request from the i2c subsystem. It got a little
delayed because I needed to wait for a dependency to be included
(commit b424080a9e: "reset: Add optional resets and stubs"). Plus,
I had some email problems. All done now, the highlights are:
- drivers can now deprecate their use of i2c classes. That shouldn't
be used on embedded platforms anyhow and was often blindly
copy&pasted. This mechanism gives users time to switch away and
ultimately boot faster once the use of classes for those drivers is
gone for good.
- new drivers for QUP, Cadence, efm32
- tracepoint support for I2C and SMBus
- bigger cleanups for the mv64xxx, nomadik, and designware drivers
And the usual bugfixes, cleanups, feature additions. Most stuff has
been in linux-next for a while. Just some hot fixes and new drivers
were added a bit more recently."
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (63 commits)
i2c: cadence: fix Kconfig dependency
i2c: Add driver for Cadence I2C controller
i2c: cadence: Document device tree bindings
Documentation: i2c: improve section about flags mangling the protocol
i2c: qup: use proper type fro clk_freq
i2c: qup: off by ones in qup_i2c_probe()
i2c: efm32: fix binding doc
MAINTAINERS: update I2C web resources
i2c: qup: New bus driver for the Qualcomm QUP I2C controller
i2c: qup: Add device tree bindings information
i2c: i2c-xiic: deprecate class based instantiation
i2c: i2c-sirf: deprecate class based instantiation
i2c: i2c-mv64xxx: deprecate class based instantiation
i2c: i2c-designware-platdrv: deprecate class based instantiation
i2c: i2c-davinci: deprecate class based instantiation
i2c: i2c-bcm2835: deprecate class based instantiation
i2c: mv64xxx: Fix reset controller handling
i2c: omap: fix usage of IS_ERR_VALUE with pm_runtime_get_sync
i2c: efm32: new bus driver
i2c: exynos5: remove unnecessary cast of void pointer
...
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior.
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V.
- Add GPIO descriptor based slot-gpio card detect API.
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c.
- mmci: Support HW busy detection on ux500.
- omap: Support MMC_ERASE.
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23.
- rtsx: Support pre-req/post-req async.
- sdhci: Add support for Realtek RTS5250 controllers.
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect.
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support.
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6S8w
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.15:
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V
- Add GPIO descriptor based slot-gpio card detect API
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c
- mmci: Support HW busy detection on ux500
- omap: Support MMC_ERASE
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23
- rtsx: Support pre-req/post-req async
- sdhci: Add support for Realtek RTS5250 controllers
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs"
* tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (102 commits)
mmc: sdhci-acpi: Intel SDIO has broken card detect
mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller
mmc: sdhci-msm: Add platform_execute_tuning implementation
mmc: sdhci-msm: Initial support for Qualcomm chipsets
mmc: sdhci-msm: Qualcomm SDHCI binding documentation
sdhci: only reprogram retuning timer when flag is set
mmc: rename ARCH_BCM to ARCH_BCM_MOBILE
mmc: sdhci: Allow for irq being shared
mmc: sdhci-acpi: Add device id 80860F16
mmc: sdhci-acpi: Fix broken card detect for ACPI HID 80860F14
mmc: slot-gpio: Add GPIO descriptor based CD GPIO API
mmc: slot-gpio: Split out CD IRQ request into a separate function
mmc: slot-gpio: Record GPIO descriptors instead of GPIO numbers
Revert "dts: socfpga: Add support for SD/MMC on the SOCFPGA platform"
mmc: sdhci-spear: use generic card detection gpio support
mmc: sdhci-spear: remove support for power gpio
mmc: sdhci-spear: simplify resource handling
mmc: sdhci-spear: fix platform_data usage
mmc: sdhci-spear: fix error handling paths for DT
mmc: sdhci-bcm-kona: fix build errors when built-in
...
Pull more powerpc updates from Ben Herrenschmidt:
"Here are a few more powerpc things for you.
So you'll find here the conversion of the two new firmware sysfs
interfaces to the new API for self-removing files that Greg and Tejun
introduced, so they can finally remove the old one.
I'm also reverting the hwmon driver for powernv. I shouldn't have
merged it, I got a bit carried away here. I hadn't realized it was
never CCed to the relevant maintainer(s) and list(s), and happens to
have some issues so I'm taking it out and it will come back via the
proper channels.
The rest is a bunch of LE fixes (argh, some of the new stuff was
broken on LE, I really need to start testing LE myself !) and various
random fixes here and there.
Finally one bit that's not strictly a fix, which is the HVC OPAL
change to "kick" the HVC thread when the firmware tells us there is
new incoming data. I don't feel like waiting for this one, it's
simple enough, and it makes a big difference in console responsiveness
which is good for my nerves"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (26 commits)
powerpc/powernv Adapt opal-elog and opal-dump to new sysfs_remove_file_self
Revert "powerpc/powernv: hwmon driver for power values, fan rpm and temperature"
power, sched: stop updating inside arch_update_cpu_topology() when nothing to be update
powerpc/le: Avoid creatng R_PPC64_TOCSAVE relocations for modules.
arch/powerpc: Use RCU_INIT_POINTER(x, NULL) in platforms/cell/spu_syscalls.c
powerpc/opal: Add missing include
powerpc: Convert last uses of __FUNCTION__ to __func__
powerpc: Add lq/stq emulation
powerpc/powernv: Add invalid OPAL call
powerpc/powernv: Add OPAL message log interface
powerpc/book3s: Fix mc_recoverable_range buffer overrun issue.
powerpc: Remove dead code in sycall entry
powerpc: Use of_node_init() for the fakenode in msi_bitmap.c
powerpc/mm: NUMA pte should be handled via slow path in get_user_pages_fast()
powerpc/powernv: Fix endian issues with sensor code
powerpc/powernv: Fix endian issues with OPAL async code
tty/hvc_opal: Kick the HVC thread on OPAL console events
powerpc/powernv: Add opal_notifier_unregister() and export to modules
powerpc/ppc64: Do not turn AIL (reloc-on interrupts) too early
powerpc/ppc64: Gracefully handle early interrupts
...
The patch adds asm macros for inc_preempt_count and dec_preempt_count_ti
(which also gets the current thread_info) instead of open-coding them in
arch/arm/vfp/*.S files.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Arun KS <getarunks@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
asm/assembler.h is a better place for this macro since it is used by
asm files outside arch/arm/kernel/
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Arun KS <getarunks@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Print extra debugging information to the console if the kernel or a user
space process crashed (with user space debugging enabled):
- contents of control register 7 and 13
- failing address and translation exception identification
- page table walk for the failing address
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
smp_stop_cpu() should stop the current cpu even for !CONFIG_SMP.
Otherwise machine_halt() will return and and the machine generates a
panic instread of simply stopping the current cpu:
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000000
CPU: 0 PID: 1 Comm: systemd-shutdow Not tainted 3.14.0-01527-g2b6ef16a6bc5 #10
[...]
Call Trace:
([<0000000000110db0>] show_trace+0xf8/0x158)
[<0000000000110e7a>] show_stack+0x6a/0xe8
[<000000000074dba8>] panic+0xe4/0x268
[<0000000000140570>] do_exit+0xa88/0xb2c
[<000000000016e12c>] SyS_reboot+0x1f0/0x234
[<000000000075da70>] sysc_nr_ok+0x22/0x28
[<000000007d5a09b4>] 0x7d5a09b4
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The git commit c63badebfe
"s390: optimize control register update" broke the update for
control register 0. After the update do the lctlg from the correct
value.
Cc: <stable@vger.kernel.org> # 3.14
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
