This is a squash of the following commits:
Revert "drm/i915: Drop intel_update_sprite_watermarks"
This reverts commit 47c99438b5.
Revert "drm/i915/ivb: Move WaCxSRDisabledForSpriteScaling w/a to atomic check"
This reverts commit 7809e5ae35.
Revert "drm/i915/skl: Eliminate usage of pipe_wm_parameters from SKL-style WM (v3)"
This reverts commit 3a05f5e2e7.
With these reverts, SKL finally stops failing every single FBC test
with FIFO underrun error messages. After some brief testing, it also
seems that this commit prevents the machine from completely freezing
when we run igt/kms_fbc_crc (see fd.o #92355).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92355
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's been reported that the atomic watermark series triggers some
regressions on SKL, which we haven't been able to track down yet. Let's
temporarily revert these patches while we track down the root cause.
This commit squashes the reverts of:
76305b1 drm/i915: Calculate watermark configuration during atomic check (v2)
a4611e4 drm/i915: Don't set plane visible during HW readout if CRTC is off
a28170f drm/i915: Calculate ILK-style watermarks during atomic check (v3)
de4a9f8 drm/i915: Calculate pipe watermarks into CRTC state (v3)
de165e0 drm/i915: Refactor ilk_update_wm (v3)
Reference: http://lists.freedesktop.org/archives/intel-gfx/2015-October/077190.html
Cc: "Zanoni, Paulo R" <paulo.r.zanoni@intel.com>
Cc: "Vetter, Daniel" <daniel.vetter@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The link training functions had confusing names. The start function
actually does the clock recovery phase of the link training, and the
complete function does the channel equalization. So call them that
instead. Also, every call to intel_dp_start_link_train() was followed
by a call to intel_dp_complete_link_train(), so add a new start
function that calls clock_recory and channel_equalization.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Latest VBT mentions which set of registers will be used for BLC,
as controller number field. Making use of this field in BXT
BLC implementation. Also, the registers are used in case control
pin indicates display DDI. Adding a check for this.
According to Bspec, BLC_PWM_*_2 uses the display utility pin for output.
To use backlight 2, enable the utility pin with mode = PWM
v2: Jani's review comments
addressed
- Add a prefix _ to BXT BLC registers definitions.
- Add "bxt only" comment for u8 controller
- Remove control_pin check for DDI controller
- Check for valid controller values
- Set pipe bits in UTIL_PIN_CTL
- Enable/Disable UTIL_PIN_CTL in enable/disable_backlight()
- If BLC 2 is used, read active_low_pwm from UTIL_PIN polarity
Satheesh's review comment addressed
- If UTIL PIN is already enabled, BIOS would have programmed it. No
need to disable and enable again.
v3: Jani's review comments
- add UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK
- Disable UTIL_PIN if controller 1 is used
- Mask out UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK before enabling
UTIL_PIN
- check valid controller value in intel_bios.c
- add backlight.util_pin_active_low
- disable util pin before enabling
v4: Change for BXT-PO branch:
Stubbed unwanted definition which was existing before
because of DC6 patch.
UTIL_PIN_MODE_PWM (0x1b << 24)
v2: Fixed Jani's review comment.
v3: Split the backight PWM frequency programming into separate patch,
in cases BIOS doesn't initializes it.
v4: Starting afresh and not modifying existing state for backlight, as
per Jani's recommendation.
v5: Fixed Jani's review comment wrt util pin enable
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Don't forget to actually check the cstate->active value when
tallying up the number of active CRTC's. (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A future patch will calculate these during the atomic 'check' phase
rather than at WM programming time, so let's store the watermark
values we're planning to use in the CRTC state; the values actually
active on the hardware remains in intel_crtc.
While we're at it, do some minor restructuring to keep ILK and SKL
values in a union.
v2: Don't move cxsr_allowed to state (Maarten)
v3: Only calculate watermarks in state. Still keep active watermarks in
intel_crtc itself. (Ville)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The only platform that still has an update_sprite_wm entrypoint is SKL;
on SKL, intel_update_sprite_watermarks just updates intel_plane->wm and
then performs a regular watermark update. However intel_plane->wm is
only used to update a couple fields in intel_wm_config, and those fields
are never used by the SKL code, so on SKL an update_sprite_wm is
effectively identical to an update_wm call. Since we're already
ensuring that the regular intel_update_wm is called any time we'd try to
call intel_update_sprite_watermarks, the whole call is redundant and can
be dropped.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Determine whether we need to apply this workaround at atomic check time
and just set a flag that will be used by the main watermark update
routine.
Moving this workaround into the atomic framework reduces
ilk_update_sprite_wm() to just a standard watermark update, so drop it
completely and just ensure that ilk_update_wm() is called whenever a
sprite plane is updated in a way that would affect watermarks.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Previously we've relied on having basically one backlight and one
backlight type per platform. This is already a bit quirky with PMIC PWM
support on VLV/CHV platforms with MIPI DSI. In the foreseeable future
we'll have at least DPCD based backlight control on eDP and DCS command
based backlight control on MIPI DSI. Backlight is becoming more and more
connector specific, so reflect this fact by making the backlight control
hooks connector specific.
This enables further work to reuse generic backlight code in
intel_panel.c while adding more specific backlight code accessed via the
hooks.
Cc: Deepak M <m.deepak@intel.com>
Cc: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Deepak M <m.deepak@intel.com>
Reviewed-by: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Handle the HDMI aspect ratio property the same way in the SDVO code
as we handle it in the HDMI code.
v2: Remove stray whitespace change
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make adjusted_mode const whereever we don't have to modify it. This only
covers cases when we have a local adjusted_mode variable, and doesn't
make any difference for cases where we just dereference
pipe_config->adjusted_mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge to catch up with 4.3. slightly more involved conflict in the
irq code, but nothing beyond adjacent changes.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The vblank counts are u32 so make flip_queued_vblank and
flip_ready_vblank u32 as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be needed for NV12 support.
v2: Rebase.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I only tested this on BDW and SKL, but since the register description
is the same ever since gen4, let's assume that all gens take the same
register format. If that's not true, then hopefully someone will
bisect a bug to this patch and we'll fix it.
Notice that the wrong fence offset register just means that the
hardware tracking will be wrong.
Testcases:
- igt/kms_frontbuffer_tracking/fbc-1p-primscrn-pri-shrfb-draw-mmap-gtt
- igt/kms_frontbuffer_tracking/fbc-2p-primscrn-pri-shrfb-draw-mmap-gtt
v2:
- Add intel_crtc->adjusted_{x,y} so this code can work independently
of intel_gen4_compute_page_offset(). (Ville).
- This version also works on SKL.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The Bspec is very clear that Live status must be checked about before
trying to read EDID over DDC channel. This patch makes sure that HDMI
EDID is read only when live status is up.
The live status doesn't seem to perform very consistent across various
platforms when tested with different monitors. The reason behind that is
some monitors are late to provide right voltage to set live_status up.
So, after getting the interrupt, for a small duration, live status reg
fluctuates, and then settles down showing the correct staus.
This is explained here in, in a rough way:
HPD line ________________
|\ T1 = Monitor Hotplug causing IRQ
| \______________________________________
| |
| |
| | T2 = Live status is stable
| | _____________________________________
| | /|
Live status _____________|_|/ |
| | |
| | |
| | |
T0 T1 T2
(Between T1 and T2 Live status fluctuates or can be even low, depending on
the monitor)
After several experiments, we have concluded that a max delay
of 30ms is enough to allow the live status to settle down with
most of the monitors. This total delay of 30ms has been split into
a resolution of 3 retries of 10ms each, for the better cases.
This delay is kept at 30ms, keeping in consideration that, HDCP compliance
expect the HPD handler to respond a plug out in 100ms, by disabling port.
v2: Adding checks for VLV/CHV as well. Reusing old ibx and g4x functions
to check digital port status. Adding a separate function to get bxt live
status (Daniel)
v3: Using intel_encoder->hpd_pin to check the live status (Siva)
Moving the live status read to intel_hdmi_probe and passing parameter
to read/not to read the edid. (me)
v4:
* Added live status check for all platforms using
intel_digital_port_connected.
* Rebased on top of Jani's DP cleanup series
* Some monitors take time in setting the live status. So retry for few
times if this is a connect HPD
v5: Removed extra "drm/i915" from commit message. Adding Shashank's sob
which was missed.
v6: Drop the (!detect_edid && !live_status check) check because for DDI
ports which are enumerated as hdmi as well as DP, we don't have a
mechanism to differentiate between DP and hdmi inside the encoder's
hot_plug. This leads to call to the hdmi's hot_plug hook for DP as well
as hdmi which leads to issues during unplug because of the above check.
v7: Make intel_digital_port_connected global in this patch, some
reformatting of while loop, adding a print when live status is not
up. (Rodrigo)
v8: Rebase it on nightly which involved skipping the hot_plug hook for now
and letting the live_status check happen in detect until the hpd handling
part is finalized (Daniel)
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I used these additional fields to track down the issue I saw on HSW.
v2: move debug fields into a substruct (Ville)
v3: clean up debug code more (Ville)
References: https://bugs.freedesktop.org/show_bug.cgi?id=91579
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Instead of doing a hack during primary plane commit the state
is updated during atomic evasion. It handles differences in
pipe size and the panel fitter.
This is continuing on top of Daniel's work to make faster
modesets atomic, and not yet enabled by default.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet:
- simplify/future-proof if ladder that Jesse spotted
- resolve conflict in pipe_config_check and don't spuriously move the
code.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds the intel_connector initialized to intel_hdmi
display, during the init phase, just like the other encoders do.
This attachment is very useful when we need to extract the connector
pointer during the hotplug handler function
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This removes the need to separately track fb changes i915.
That will be done as a separate commit, however.
Changes since v1:
- Add dri-devel to cc.
- Fix a check in intel's prepare and cleanup fb to take rotation
into account.
Changes since v2:
- Split out i915 changes to a separate commit.
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
[danvet: Squash in msm fixup from Maarten.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no need to have a separate flag for tps3 as the information is
only used at one location. Move the logic there to make it easier to
follow.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge -fixes since there's more DDI-E related cleanups on top of
the pile of -fixes for skl that just landed for 4.3.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i914/intel_dp.c
drivers/gpu/drm/i915/intel_lrc.c
Conflicts are all fairly harmless adjacent line stuff.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This makes the error message slightly more useful.
Changes since v1:
- Use ktime_get() while irqs are still disabled. (vsyrjala)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's already a per crtc member that can be used for it.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make it available outside of intel_dp.c.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DP MST encoder config function never sets ddi_pll_sel, even though
its value is programmed in its ->pre_enable() hook. That used to work
because a new pipe_config was kzalloc'ed at every modeset, and the value
of zero selects the highest clock for the PLL. Starting with the commit
below, the value of ddi_pll_sel is preserved through modesets, and since
the correct value wasn't properly setup by the MST code, it could lead
to warnings and blank screens.
commit 8504c74c7a
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Fri May 15 11:51:50 2015 +0300
drm/i915: Preserve ddi_pll_sel when allocating new pipe_config
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91628
Cc: stable@vger.kernel.org # 7e6313a251 drm/i915: Don't use link_bw for PLL setup
Cc: stable@vger.kernel.org
Cc: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Normmally the common lane in a PHY channel gets powered up when some
of the data lanes get powered up. But when we're driving port B with
pipe B we don't want to enabled any of the data lanes, and just want
the DPLL in the common lane to be active.
To make that happens we have to temporarily enable some data lanes
after which we can access the DPLL registers in the common lane. Once
the pipe is up and running we can drop the power override on the data
lanes allowing them to shut down. From this point forward the common
lane will in fact stay powered on until the data lanes in the other
channel get powered down.
Ville's extended explanation from the review thread:
On Wed, Aug 19, 2015 at 07:47:41AM +0530, Deepak wrote:
> One Q, why only for port B? Port C is also in same common lane right?
Port B is in the first PHY channel which also houses CL1. CL1 always
powers up whenever any lanes in either PHY channel are powered up.
CL2 only powers up if lanes in the second channel (ie. the one with
port C) powers up.
So in this scenario (pipe B->port B) we want the DPLL from CL2, but
ideally we only want to power up the lanes for port B. Powering up
port B lanes will only power up CL1, but as we need CL2 instead we
need to, temporarily, power up some lanes in port C as well.
Crossing the streams the other way (pipe A->port C) is not a problem
since CL1 powers up whenever anything else powers up. So powering up
some port C lanes is enough on its own to make the CL1 DPLL
operational, even though CL1 and the lanes live in separate channels.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
[danvet: Amend commit message with extended explanation.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Powergate the PHY lanes when they're not needed. For HDMI all four lanes
are needed always, but for DP we can enable only the needed lanes. To
power down the unused lanes we use some power down override bits in the
DISPLAY_PHY_CONTROL register. Without the overrides it appears that the
hardware always powers on all the lanes. When the port is disabled the
power down override is not needed and the lanes will shut off on their
own. That also means the override is critical to actually be able to
access the DPIO registers before the port is actually enabled.
Additionally the common lanes will power down when not needed. CL1
remains on as long as anything else is on, CL2 will shut down when
all the lanes in the same channel will shut down. There is one exception
for CL2 that will be dealt in a separate patch for clarity.
With potentially some lanes powered down, the DP code now has to check
the number of active lanes before accessing PCS/TX registers. All
registers in powered down blocks will reads as 0xffffffff, and soe we
would drown in warnings from vlv_dpio_read() if we allowed the code
to access all those registers.
Another important detail in the DP code is the "TX latency optimal"
setting. Normally the second TX lane acts as some kind of reset master,
with the other lanes as slaves. But when only a single lane is enabled,
that single lane obviously has to be the master.
A bit of extra care is needed to reconstruct the initial state of the
DISPLAY_PHY_CONTROL register since it can't be read safely. So instead
read the actual lane status from the DPLL/PHY_STATUS registers and
use that to determine which lanes ought to be powergated initially.
We also need to switch the PHY power modes to "deep PSR" to avoid
a hard system hang when powering down the single channel PHY.
Also sprinkle a few debug prints around so that we can monitor the
DISPLAY_PHY_STATUS changes without having to read it and risk
corrupting it.
v2: Add locking to chv_powergate_phy_lanes()
v3: Actually enable dynamic powerdown in the PHY and deal with the
fallout
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The function can be made static there. No functional changes.
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add vlv_dport_to_phy() and fix up the return values of
vlv_dport_to_channel() and vlv_pipe_to_channel() to use
the appropriate enums.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the CHV clock buffer disable from chv_disable_pll() to the new
encoder .post_pll_disable() hook. This is more symmetric since the
clock buffer enable happens from the .pre_pll_enable() hook.
We'll have more use for the new hook soon.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With MST there won't be a crtc assigned to the main link encoder, so
trying to dig up the pipe_config from there is a recipe for an oops.
Instead store the parameters (lane_count and link_rate) in the encoder,
and use those values during link training etc. Since those parameters
are now assigned only when the link is actually enabled,
.compute_config() won't clobber them as it did before.
Hardware state readout is still bonkers though as we don't transfer the
link parameters from pipe_config intel_dp. We should do that during
encoder sanitation. But since we don't even do a proper job of reading
out the main link encoder state for MST there's littel point in
worrying about this now.
Fixes a regression with MST caused by:
commit 90a6b7b052
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Jul 6 16:39:15 2015 +0300
drm/i915: Move intel_dp->lane_count into pipe_config
v2: Different apporoach that should keep intel_dp_check_mst_status()
somewhat less oopsy
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bunch more fixes for 4.3, most of it skl fallout. It's not quite all yet,
there's still a few more patches pending to enable DDI-E correctly on skl.
Also included the dpms atomic work from Maarten since atomic is just a
pain and not including would cause piles of conflicts right from the
start.
* tag 'drm-intel-next-fixes-2015-08-16' of git://anongit.freedesktop.org/drm-intel: (67 commits)
drm/i915: Per-DDI I_boost override
drm/i915/skl: WaIgnoreDDIAStrap is forever, always init DDI A
drm/i915: fix checksum write for automated test reply
drm/i915: Contain the WA_REG macro
drm/i915: Remove the failed context from the fpriv->context_idr
drm/i915: Report IOMMU enabled status for GPU hangs
drm/i915: Check idle to active before processing CSQ
drm/i915: Set alternate aux for DDI-E
drm/i915: Set power domain for DDI-E
drm/i915: fix stolen bios_reserved checks
drm/i915: Use masked write for Context Status Buffer Pointer
drm/i915/skl WaDisableSbeCacheDispatchPortSharing
drm/i915: Spam less on dp aux send/receive problems
drm/i915: Handle return value in intel_pin_and_fence_fb_obj, v2.
drm/i915: Only update mode related state if a modeset happened.
drm/i915: Remove connectors_active.
drm/i915: Remove connectors_active from intel_dp.c, v2.
drm/i915: Remove connectors_active from sanitization, v2.
drm/i915: Get rid of dpms handling.
drm/i915: Make crtc checking use the atomic state, v2.
...
We only need the link_bw/rate_select parameters when starting link
training, and they should be computed based on the currently active
config, so throw them out from intel_dp and just compute on demand.
Toss in an extra debug print to see rate_select in addition to link_bw,
as the latter may be 0 for eDP 1.4.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we clobber intel_dp->lane_count in compute config, which means
after a rejected modeset we may no longer be able to retrain the current
link. Move lane_count into pipe_config to avoid that.
v2: Add missing ':' to the pipe config debug dump
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we treat intel_{dp,hdmi}->color_range as partly user
controller value (via the property) but we also change it during
.compute_config() when using the "Automatic" mode. That is a bit
confusing, so let's just change things so that we store the user
property values in intel_dp, and only change what's stored in
pipe_config during .compute_config().
There should be no functional change.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By Vesa DP 1.2 Spec TEST_CRC_COUNT should be
"reset to 0 when TEST_SINK bit 0 = 0."
However for some strange reason when PSR is enabled in
certain platforms this is not true. At least not immediatelly.
So we face cases like this:
first get_sink_crc operation:
count: 0, crc: 000000000000
count: 1, crc: c101c101c101
returned expected crc: c101c101c101
secont get_sink_crc operation:
count: 1, crc: c101c101c101
count: 0, crc: 000000000000
count: 1, crc: 0000c1010000
should return expected crc: 0000c1010000
But also the reset to 0 should be faster resulting into:
get_sink_crc operation:
count: 1, crc: c101c101c101
count: 1, crc: 0000c1010000
should return expected crc: 0000c1010000
So in order to know that the second one is valid one
we need to compare the pair (count, crc) with latest (count, crc).
If the pair changed you have your valid CRC.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By Vesa DP spec, test counter at DP_TEST_SINK_MISC just reset to 0
when unsetting DP_TEST_SINK_START, so let's force this stop here.
But let's minimize the aux transactions and just do it when we know
it hasn't been properly stoped.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are no more users, byebye!
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is now done completely atomically.
Keep connectors_active for now, but make it mirror crtc_state->active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
First step in removing dpms and validating atomic state.
There can still be a mismatch in the connector state because the dpms
callbacks are still used, but this can not happen immediately after a modeset.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of our own duplicated one. This fixes a bug in the driver
unload code if DRM_FBDEV_EMULATION=n but DRM_I915_FBDEV=y because we
try to unregister the nonexistent fbdev drm_framebuffer.
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need a few core drm patches to be able to merge Maarten's series to
convert DPMS over to atomic.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Due to the way busy_bits was handled, we were not doing any flushes if
we didn't previously get an invalidate. Since it's possible to get
flushes without an invalidate first, remove the busy_bits early
return.
So now that we don't have the busy_bits guard anymore we'll need the
origin check for the GTT tracking (we were not doing anything on GTT
flushes due to the GTT check at invalidate()).
As a last detail, since we can get multiple consecutive flushes,
disable FBC before updating it, otherwise intel_fbc_update() will just
keep FBC enabled instead of restarting it.
Notice that this does not fix any of the current IGT tests due to the
fact that we still have a few intel_fbc() calls at points where we
also have the frontbuffer tracking calls: we didn't fully convert to
frontbuffer tracking yet. Once we remove those calls and start relying
only on the frontbuffer tracking infrastructure we'll need this patch.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is required to properly handle failing dpms calls.
When making a wait in i915 interruptible, I've noticed
that the dpms sequence could fail with -ERESTARTSYS because
it was waiting interruptibly for flips. So from now on
allow drivers to fail in their connector dpms callback.
Encoder and crtc dpms callbacks are unaffected.
Changes since v1:
- Update kerneldoc for the drm helper functions.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[danvet: Resolve conflicts due to different merge order.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
crystalcove pmic support from Shobhit. Patch series has all acks/r-bs from
other mainainers so ok to pull into drm-next. But I'm cc'ing all other
maintainers as fyi and in case they want to pull it into their trees too
to avoid conflicts.
* tag 'topic/crc-pmic-2015-07-23' of git://anongit.freedesktop.org/drm-intel:
mfd: Add GPIOLIB dependency if INTEL_SOC_PMIC is to be enabled
drm/i915: Backlight control using CRC PMIC based PWM driver
drm/i915: Use the CRC gpio for panel enable/disable
pwm: crc: Add Crystalcove (CRC) PWM driver
mfd: intel_soc_pmic_core: ADD PWM lookup table for CRC PMIC based PWM
mfd: intel_soc_pmic_crc: Add PWM cell device for Crystalcove PMIC
mfd: intel_soc_pmic_core: Add lookup table for Panel Control as GPIO signal
gpiolib: Add support for removing registered consumer lookup table
Use the CRC PWM device in intel_panel.c and add new MIPI backlight
specififc callbacks
v2: Modify to use pwm_config callback
v3: Addressed Jani's comments
- Renamed all function as pwm_* instead of vlv_*
- Call intel_panel_actually_set_backlight in enable function
- Return -ENODEV in case pwm_get fails
- in case pwm_config error return error cdoe from pwm_config
- Cleanup pwm in intel_panel_destroy_backlight
v4: Removed unused #defines and initialized backlight with INVALID_PIPE (Ville)
CC: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we both set mode->private_flags to some value and also use
the pipe_config quirk. But since the pipe_config quirk isn't tied to
the lifetime of the mode object we need to check both.
Simplify this by only using mode.private_flags and stop using the
INHERITED_MODE quirk. Also for clarity add an explicit #define for
that driver priavete mode flag.
By using crtc_state->mode_changed we can also remove the recalc local
variable.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This can only fail because of a bug in the code.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[danvet: Squash in follow-up to also remove start_vbl_count from
intel_crtc->atomic and put it into the intel_crtc directly - it's not
precomputed state.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
