The "follow" fail_over_mac policy is useful for multiport devices that
either become confused or incur a performance penalty when multiple
ports are programmed with the same MAC address, but the same MAC
address still may happened by this steps for this policy:
1) echo +eth0 > /sys/class/net/bond0/bonding/slaves
bond0 has the same mac address with eth0, it is MAC1.
2) echo +eth1 > /sys/class/net/bond0/bonding/slaves
eth1 is backup, eth1 has MAC2.
3) ifconfig eth0 down
eth1 became active slave, bond will swap MAC for eth0 and eth1,
so eth1 has MAC1, and eth0 has MAC2.
4) ifconfig eth1 down
there is no active slave, and eth1 still has MAC1, eth2 has MAC2.
5) ifconfig eth0 up
the eth0 became active slave again, the bond set eth0 to MAC1.
Something wrong here, then if you set eth1 up, the eth0 and eth1 will have the same
MAC address, it will break this policy for ACTIVE_BACKUP mode.
This patch will fix this problem by finding the old active slave and
swap them MAC address before change active slave.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Tested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJVp19MAAoJEP5prqPJtc/HsA8IAIqYKwJtXHItVoG6GBxLo/iJ
G6OhCxSgDPUdytdyvWRmYL+2g6q9+BefnApwGroM0wowytHx4I6kF2O4LKEvthnD
TzDV6uY0n1CR8FzCdfQdTFedAfxIx7DLCqY/iC+JRFTh6Vhvj46WtHickthu4Se+
ygTWg5f5Da086JTUtwbb75TCHJv8xxtN57t6yZTtDoyaftqWd1Dzrmi8dBwHRWBA
6X/rE4VekFwFCbqOlv5ghm86lD77sMTEaU0xkm9FeZmO/CnUD3JASwi844RtCqXR
wj3OJ89qH14YmpJwjpakIwHfTyyPJurzPpPkCTZ6awmdNhCvp+h3nbfjKRqs0WU=
=pQGs
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.2-20150716' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-07-16
this is a pull request of 2 patches by Stefan Agner. He fixes the resume
operation in the mcp251x driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts 19424e052f ("sit:
Add gro callbacks to sit_offload") because it generates packets
that cannot be handled even by our own GSO.
Reported-by: Wolfgang Walter <linux@stwm.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
7445E0 contains an ECO which disconnected the internal SF2 pseudo-PHY which was
known to conflict with the external pseudo-PHY of BCM53125 switches. This
motivated the need to utilize the internal SF2 MDIO controller via indirect
register reads/writes to control external Broadcom switches due to this address
conflict (both responded at address 30d).
For 7445E0, the internal pseudo-PHY of the SF2 switch got disconnected, and as
a consequence this prevents the internal SF2 MDIO bus controller from reading
data (reads back everything as 0) since the MDI line is tied low.
Fix this by making the indirect register reads and writes conditional to
7445D0, on 7445E0 we can utilize the SWITCH_MDIO controller (backed by
mdio-unimac and not the DSA created slave MII bus).
We utilize of_machine_is_compatible() here since this is the only way for use
to differentiate between these two chips in a way that does not violate layers
or becomes (too) vendor-specific.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the bond is enslaving a device with different type it will be setup
by it, but if after being setup the enslave fails the bond doesn't
switch back its type and also keeps pointers to foreign structures that can
be long gone. Thus revert back any type changes if the enslave failed and
the bond had to change its type.
Example:
Before patch:
$ echo lo > bond0/bonding/slaves
-bash: echo: write error: Cannot assign requested address
$ ip l sh bond0
20: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default
link/loopback 16:54:78:34:bd:41 brd 00:00:00:00:00:00
$ echo +eth1 > bond0/bonding/slaves
$ ip l sh bond0
20: bond0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT group default qlen 1000
link/ether 52:54:00:3f:47:69 brd ff:ff:ff:ff:ff:ff
(notice the MASTER flag is gone)
After patch:
$ echo lo > bond0/bonding/slaves
-bash: echo: write error: Cannot assign requested address
$ ip l sh bond0
21: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default qlen 1000
link/ether 6e:66:94:f6:07:fc brd ff:ff:ff:ff:ff:ff
$ echo +eth1 > bond0/bonding/slaves
$ ip l sh bond0
21: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN
mode DEFAULT group default qlen 1000
link/ether 52:54:00:3f:47:69 brd ff:ff:ff:ff:ff:ff
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: e36b9d16c6 ("bonding: clean muticast addresses when device changes type")
Signed-off-by: David S. Miller <davem@davemloft.net>
Return codes aren't honored properly in cpufreq_set_policy(). This can
lead to two problems:
- wrong errors propagated to sysfs
- we try to do next state-change even if the previous one failed
cpufreq_governor_dbs() now returns proper errors on all invalid
state-transition requests and this code should honor that.
Reviewed-and-tested-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With previous commit, governors have started to return errors on invalid
state-transition requests. We already have a WARN for an invalid
state-transition request in cpufreq_governor_dbs(). This does trigger
today, as the sequence of events isn't guaranteed by cpufreq core.
Lets stop warning on that for now, and make sure we don't enter an
invalid state.
Reviewed-and-tested-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There can be races where the request has come to a wrong state. For
example INIT followed by STOP (instead of START) or START followed by
EXIT (instead of STOP).
Address these races by making sure the state-machine never gets into
any invalid state. Also return an error if an invalid state-transition
is requested.
Reviewed-and-tested-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some part of cs_dbs_timer() and od_dbs_timer() is exactly same and is
unnecessarily duplicated.
Create the real work-handler in cpufreq_governor.c and put the common
code in this routine (dbs_timer()).
Shouldn't make any functional change.
Reviewed-and-tested-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some information is common to all CPUs belonging to a policy, but are
kept on per-cpu basis. Lets keep that in another structure common to all
policy->cpus. That will make updates/reads to that less complex and less
error prone.
The memory for cpu_common_dbs_info is allocated/freed at INIT/EXIT, so
that it we don't reallocate it for STOP/START sequence. It will be also
be used (in next patch) while the governor is stopped and so must not be
freed that early.
Reviewed-and-tested-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
drm_vblank_on() now warns on nested use or if vblank is not properly
initialized. This patch fixes Atmel HLCDC vblank initial state.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
When the bonding is being unloaded and the netdevice notifier is
unregistered it executes NETDEV_UNREGISTER for each device which should
remove the bond's proc entry but if the device enslaved is not of
ARPHRD_ETHER type and is in front of the bonding, it may execute
bond_release_and_destroy() first which would release the last slave and
destroy the bond device leaving the proc entry and thus we will get the
following error (with dynamic debug on for bond_netdev_event to see the
events order):
[ 908.963051] eql: event: 9
[ 908.963052] eql: IFF_SLAVE
[ 908.963054] eql: event: 2
[ 908.963056] eql: IFF_SLAVE
[ 908.963058] eql: event: 6
[ 908.963059] eql: IFF_SLAVE
[ 908.963110] bond0: Releasing active interface eql
[ 908.976168] bond0: Destroying bond bond0
[ 908.976266] bond0 (unregistering): Released all slaves
[ 908.984097] ------------[ cut here ]------------
[ 908.984107] WARNING: CPU: 0 PID: 1787 at fs/proc/generic.c:575
remove_proc_entry+0x112/0x160()
[ 908.984110] remove_proc_entry: removing non-empty directory
'net/bonding', leaking at least 'bond0'
[ 908.984111] Modules linked in: bonding(-) eql(O) 9p nfsd auth_rpcgss
oid_registry nfs_acl nfs lockd grace fscache sunrpc crct10dif_pclmul
crc32_pclmul crc32c_intel ghash_clmulni_intel ppdev qxl drm_kms_helper
snd_hda_codec_generic aesni_intel ttm aes_x86_64 glue_helper pcspkr lrw
gf128mul ablk_helper cryptd snd_hda_intel virtio_console snd_hda_codec
psmouse serio_raw snd_hwdep snd_hda_core 9pnet_virtio 9pnet evdev joydev
drm virtio_balloon snd_pcm snd_timer snd soundcore i2c_piix4 i2c_core
pvpanic acpi_cpufreq parport_pc parport processor thermal_sys button
autofs4 ext4 crc16 mbcache jbd2 hid_generic usbhid hid sg sr_mod cdrom
ata_generic virtio_blk virtio_net floppy ata_piix e1000 libata ehci_pci
virtio_pci scsi_mod uhci_hcd ehci_hcd virtio_ring virtio usbcore
usb_common [last unloaded: bonding]
[ 908.984168] CPU: 0 PID: 1787 Comm: rmmod Tainted: G W O
4.2.0-rc2+ #8
[ 908.984170] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 908.984172] 0000000000000000 ffffffff81732d41 ffffffff81525b34
ffff8800358dfda8
[ 908.984175] ffffffff8106c521 ffff88003595af78 ffff88003595af40
ffff88003e3a4280
[ 908.984178] ffffffffa058d040 0000000000000000 ffffffff8106c59a
ffffffff8172ebd0
[ 908.984181] Call Trace:
[ 908.984188] [<ffffffff81525b34>] ? dump_stack+0x40/0x50
[ 908.984193] [<ffffffff8106c521>] ? warn_slowpath_common+0x81/0xb0
[ 908.984196] [<ffffffff8106c59a>] ? warn_slowpath_fmt+0x4a/0x50
[ 908.984199] [<ffffffff81218352>] ? remove_proc_entry+0x112/0x160
[ 908.984205] [<ffffffffa05850e6>] ? bond_destroy_proc_dir+0x26/0x30
[bonding]
[ 908.984208] [<ffffffffa057540e>] ? bond_net_exit+0x8e/0xa0 [bonding]
[ 908.984217] [<ffffffff8142f407>] ? ops_exit_list.isra.4+0x37/0x70
[ 908.984225] [<ffffffff8142f52d>] ?
unregister_pernet_operations+0x8d/0xd0
[ 908.984228] [<ffffffff8142f58d>] ?
unregister_pernet_subsys+0x1d/0x30
[ 908.984232] [<ffffffffa0585269>] ? bonding_exit+0x23/0xdba [bonding]
[ 908.984236] [<ffffffff810e28ba>] ? SyS_delete_module+0x18a/0x250
[ 908.984241] [<ffffffff81086f99>] ? task_work_run+0x89/0xc0
[ 908.984244] [<ffffffff8152b732>] ?
entry_SYSCALL_64_fastpath+0x16/0x75
[ 908.984247] ---[ end trace 7c006ed4abbef24b ]---
Thus remove the proc entry manually if bond_release_and_destroy() is
used. Because of the checks in bond_remove_proc_entry() it's not a
problem for a bond device to change namespaces (the bug fixed by the
Fixes commit) but since commit
f939981492 ("bonding: Don't allow bond devices to change network
namespaces.") that can't happen anyway.
Reported-by: Carol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: a64d49c3dd ("bonding: Manage /proc/net/bonding/ entries from
the netdev events")
Tested-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx_priv_state structure contains an fid_mask, where 1 means
the FID is free to use, 0 means the FID is in use.
This patch fixes the bit clear in mv88e6xxx_leave_bridge() when
assigning a new FID to a port.
Example scenario: I have 7 ports, port 5 is CPU, port 6 is unused (no
PHY). After setting the ports 0, 1 and 2 in bridge br0, and ports 3 and
4 in bridge br1, I have the following fid_mask: 0b111110010110 (0xf96).
Indeed, br0 uses FID 0, and br1 uses FID 3.
After setting nomaster for port 0, I get the wrong fid_mask: 0b10 (0x2).
With this patch we correctly get 0b111110010100 (0xf94), meaning port 0
uses FID 1, br0 uses FID 0, and br1 uses FID 3.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ANY_LAYOUT is a compatibility feature. It's implied
for VERSION_1 devices, and non-transitional devices
might not offer it. Change code to behave accordingly.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull s390 fix from Martin Schwidefsky:
"Fast path fix for the thread_struct breakage"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: adapt entry.S to the move of thread_struct
Pull AVR32 update from Hans-Christian Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
AVR32/time: Migrate to new 'set-state' interface
The dma_map_single and dma_unmap_single should set "gadget->dev.parent"
instead of "&gadget->dev" in the first argument because the parent has
a udc controller's device pointer.
Otherwise, iommu functions are not called in ARM environment.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There was an omission in transition to devm_xxx resource handling.
iounmap(udc->phy_regs) were removed, but ioremap() was left
without devm_.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 3517c31a8e ("usb: gadget: mv_udc: use devm_xxx for probe")
Signed-off-by: Felipe Balbi <balbi@ti.com>
Phy drivers and the ulpi interface providers depend on the
registration of the ulpi bus. Ulpi registers the bus in
module_init(). This could cause unnecessary bus users'
probe delays. i.e. unnecessary -EPROBE_DEFER happening on
ulpi_drivers in case they're registered before ulpi bus
itself.
Reported-by: Zhuo Qiuxu <qiuxu.zhuo@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
git commit 0c8c0f03e3
"x86/fpu, sched: Dynamically allocate 'struct fpu'"
moved the thread_struct to the end of the task_struct.
This causes some of the offsets used in entry.S to overflow their
instruction operand field. To fix this use aghi to create a
dedicated pointer for the thread_struct.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Migrate avr32 driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
We want to call cpu_idle_poll_ctrl() in shutdown only if we were in
oneshot or resume state earlier. Create another variable to save this
information and check that in shutdown callback.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
The param_val variable is what determines if schmitt
trigger is enabled on a pin or not. A typo here mean
that schmitt trigger was always enabled for standard
and i2c pins.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
imx1_pinconf_set assumes that the array of pins in struct
imx1_pinctrl_soc_info can be indexed by pin id to get the
pinctrl_pin_desc for a pin. This used to be correct up to commit
607af165c0 which removed some entries from the array and so made it
wrong to access the array by pin id.
The result of this bug is a wrong pin name in the output for small pin
ids and an oops for the bigger ones.
This patch is the result of a discussion that includes patches by Markus
Pargmann and Chris Ruehl.
Fixes: 607af165c0 ("pinctrl: i.MX27: Remove nonexistent pad definitions")
Cc: stable@vger.kernel.org
Reported-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's possible to hit a race condition if interrupts are generated on a GPIO
pin when the IRQ line in question is being disabled.
If the interrupt is freed, bcm2835_gpio_irq_disable() is called which
disables the event generation sources (edge, level). If an event occurred
between the last disabling of hard IRQs and the write to the event
source registers, a bit would be set in the GPIO event detect register
(GPEDSn) which goes unacknowledged by bcm2835_gpio_irq_handler()
so Linux complains loudly.
There is no per-GPIO mask register, so when disabling GPIO interrupts
write 1 to the relevant bit in GPEDSn to clear out any stale events.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PFC driver causes the kernel to hang on the R-Car gen2 SoC based boards
when the CPU_ALL_PORT() macro is fixed to reflect the reality, i.e. when the
GPIO space becomes actually sparse. This happens because the _GP_GPIO() macro
includes an indexed initializer which causes the "holes" (array entries filled
with all 0s) between the groups of the existing GPIOs; and the driver can't
cope with that. There seems to be no reason to use the indexed initializer,
so we can remove the index specifier and so avoid the "holes".
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit a21763a0b1
"pinctrl: nomadik: activate strict mux mode"
put all Nomadik pin controllers to strict mode. This was
not good on the Snowball platform: the muxing of GPIOs to
different pins is done with hogs in the DTS file, and then
these GPIOs are used by offset, relying on hogs to mux the
pins. Since that means the pin controller "owns" the pins
and at the same time we have a GPIO user, this pin controller
is by definition not strict.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the controller is powered up but the HDMI codec is powered down
on Skylake, the power well is turned off. When the codec is then
powered up again, we need to poke the codec a little extra to make
sure it wakes up. Otherwise we'll get sad "no response from codec"
messages and broken audio.
This also changes azx_runtime_resume to actually call
snd_hdac_set_codec_wakeup for Skylake (before STATETS read).
(Otherwise it would only have been called for Haswell and Broadwell,
which both do not need it, so this probably was not the author's
intention.)
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Two fairly simple fixes: one is a change that causes us to have a very low
queue depth leading to performance issues and the other is a null deref
occasionally in tapes thanks to use after put.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJVq2/DAAoJEDeqqVYsXL0MhqoH/2ZlycWVQ2ZQyC9k2UWjAS7t
By0ufRZKeaxgwriVWZqTCE3QHfqqeR5tNNSvk26k+CJTS6nyVGX+g8cxLQJf1gey
DyAi9za+5P5SwYFuJxzULyZddTyeshoZplVvRwjd1/gnRUJXybuO+HRkYzaROd5e
7snX56jGt1MzpmIrO2wln24pFLVfdC5JivzUcXgYecHD/XZuzOEdZE1dCxONXy27
rTeqYayIGLFo7vhSt9J9ViF0QiU6ahCKmQ/TDsv3Sq1zg228E7DAmlzVAo2NCwLM
gelTRHRdO4rwwkehZH8QIdUI77MzgmwQIU4nZp3FBG9SWrIEPHaRpiDxCHr3UE0=
=bfE2
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two fairly simple fixes: one is a change that causes us to have a very
low queue depth leading to performance issues and the other is a null
deref occasionally in tapes thanks to use after put"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: fix host max depth checking for the 'queue_depth' sysfs interface
st: null pointer dereference panic caused by use after kref_put by st_open
Pull MIPS fixes from Ralf Baechle:
"Another round of MIPS fixes for 4.2.
Things are looking quite decent at this stage but the recent work on
the FPU support took its toll:
- fix an incorrect overly restrictive ifdef
- select O32 64-bit FP support for O32 binary compatibility
- remove workarounds for Sibyte SB1250 Pass1 parts. There are rare
fixing the workarounds is not worth the effort.
- patch up an outdated and now incorrect comment"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: fpu.h: Allow 64-bit FPU on a 64-bit MIPS R6 CPU
MIPS: SB1: Remove support for Pass 1 parts.
MIPS: Require O32 FP64 support for MIPS64 with O32 compat
MIPS: asm-offset.c: Patch up various comments refering to the old filename.
Pull parisc fix from Helge Deller:
"A memory leak fix from Christophe Jaillet which was introduced with
kernel 4.0 and which leads to kernel crashes on parisc after 1-3 days"
* 'parisc-4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: mm: Fix a memory leak related to pmd not attached to the pgd
By far most of the fixes here are updates to DTS files to deal with some
mostly minor bugs.
There's also a fix to deal with non-PM kernel configs on i.MX, a
regression fix for ethernet on PXA platforms and a dependency fix for OMAP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SOgd
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"By far most of the fixes here are updates to DTS files to deal with
some mostly minor bugs.
There's also a fix to deal with non-PM kernel configs on i.MX, a
regression fix for ethernet on PXA platforms and a dependency fix for
OMAP"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: keystone: dts: rename pcie nodes to help override status
ARM: keystone: dts: fix dt bindings for PCIe
ARM: pxa: fix dm9000 platform data regression
ARM: dts: Correct audio input route & set mic bias for am335x-pepper
ARM: OMAP2+: Add HAVE_ARM_SCU for AM43XX
MAINTAINERS: digicolor: add dts files
ARM: ux500: fix MMC/SD card regression
ARM: ux500: define serial port aliases
ARM: dts: OMAP5: Add #iommu-cells property to IOMMUs
ARM: dts: OMAP4: Add #iommu-cells property to IOMMUs
ARM: dts: Fix frequency scaling on Gumstix Pepper
ARM: dts: configure regulators for Gumstix Pepper
ARM: dts: omap3: overo: Update LCD panel names
ARM: dts: cros-ec-keyboard: Add support for some Japanese keys
ARM: imx6: gpc: always enable PU domain if CONFIG_PM is not set
ARM: dts: imx53-qsb: fix TVE entry
ARM: dts: mx23: fix iio-hwmon support
ARM: dts: imx27: Adjust the GPT compatible string
ARM: socfpga: dts: Fix entries order
ARM: socfpga: dts: Fix adxl34x formating and compatible string
Acer Aspire V5 with the ALC282 codec is given the wrong value for the
0x19 PIN by the laptop's BIOS. Overriding it with the correct value
adds support for the headset microphone which would not otherwise be
visible in the system.
The fix is based on commit 7819717b11 with a similar quirk for Acer
Aspire with the ALC269 codec.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96201
Cc: <stable@vger.kernel.org>
Signed-off-by: Mateusz Sylwestrzak <matisec7@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Data is stored in the device in be16 format. Make use of be16_to_cpu and
cpu_to_be16 to have correct endianness on any host architecture.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Reviewed-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
iio_device_register should be the last operation during probe. Therefor
move up interrupt setup code and while at it, change the check for invalid
values of client->irq to be smaller than zero.
Fixes: 3dd477acbd ("iio: light: Add threshold interrupt support for STK3310")
As the device_register makes the userspace interfaces of the device available
it is possible for requests to come in before the probe sequence has finished.
This can lead to unhandled interrupts and similar.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Reviewed-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
IIO_EV_TYPE_THRESH in rising direction describes an event where the
threshold is crossed in rising direction, positive or negative values
being possible. This is not the case here.
Since the threshold is no signed value and only the magnitude is compared,
IIO_EV_TYPE_MAG is what describes the behaviour of these devices, see the
sysfs-bus-iio ABI Documentation.
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
On reading in_voltage_scale of we got an NULL pointer dereference Oops.
The reason for this is, that mcp320x_read_raw tries to access
chip_info->resolution from struct mcp320x, but chip_info is never set.
chip_info was never set since the driver was added, but there was no
acute problem, because it was not referenced.
The acute problem exists since
b12206e917
iio: adc: mcp320x. Add support for more ADCs
This patch fixes the issue by setting chip_info in mcp320x_probe.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Reviewed-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Read the register only when the adc register address is 4 byte aligned.
(rather than the other way around).
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Cc: <Stable.vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Changed the offset to negative as usual equation is: (raw +
offset)*scale and in this
case offset should be negative (as we deduct 273.15 Kelvin to get temperature
in Celsius).
Signed-off-by: Crt Mori <cmo@melexis.com>
Acked-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The RESET operation invoked in the last instance will align
in the natural way all 3 axis and the chip top view.
Without this, north and south are swapped.
Signed-off-by: Viorel Suman <viorel.suman@intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes setting the SET/RESET bit in the REG_CTRL0
register.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
According to the debug/error string, the content of chip_id is supposed to
be output, rather than the return value of the previous operation.
Fixes: c91746a236 ("iio: magn: Add support for BMC150 magnetometer")
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
bmc150_magn makes use of REGMAP_I2C, so select it to build always without
errors.
Fixes: c91746a236 ("iio: magn: Add support for BMC150 magnetometer")
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Sometimes bssid can go null on failed association.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes bssid can go null on failed association.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: <stable@vger.kernel.org> # v3.19+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
only SAMP_FREQ is writable
Will lead to SAMP_FREQ being written by any attempt to write
to the other exported attributes and hence a rather unexpected
result!
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
drivers/iio/proximity/sx9500.c: In function ‘sx9500_buffer_preenable’:
drivers/iio/proximity/sx9500.c:682: warning: ‘ret’ may be used uninitialized in this function
drivers/iio/proximity/sx9500.c: In function ‘sx9500_buffer_predisable’:
drivers/iio/proximity/sx9500.c:706: warning: ‘ret’ may be used uninitialized in this function
If active_scan_mask is empty, it will loop once more over all channels,
doing nothing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
