IRQ_NONE can be returned indirect.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Patch remove some variables initialization from core.c and drd.c
file.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Function is not used in driver so it can be removed.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It doesn't need to enable/disable L1 on the fly for EP0 transfer,
we only need to enable L1 after SET_CONFIGURATION.
This code may be introduced by careless.
Cc: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
net2272_rdk1_probe() skips "i == 1" (BAR1) during allocation of
resources. The patch does this on error hanling paths as well.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When gadget registration fails, one should not call usb_del_gadget_udc().
Ensure this by setting gadget->udc to NULL. Also in case of a failure
there is no need to disable low-level hardware, so return immiedetly
instead of jumping to error_init label.
This fixes the following kernel NULL ptr dereference on gadget failure
(can be easily triggered with g_mass_storage without any module
parameters):
dwc2 12480000.hsotg: dwc2_check_params: Invalid parameter besl=1
dwc2 12480000.hsotg: dwc2_check_params: Invalid parameter g_np_tx_fifo_size=1024
dwc2 12480000.hsotg: EPs: 16, dedicated fifos, 7808 entries in SPRAM
Mass Storage Function, version: 2009/09/11
LUN: removable file: (no medium)
no file given for LUN0
g_mass_storage 12480000.hsotg: failed to start g_mass_storage: -22
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000104
pgd = (ptrval)
[00000104] *pgd=00000000
Internal error: Oops: 805 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.8.0-rc5 #3133
Hardware name: Samsung Exynos (Flattened Device Tree)
Workqueue: events deferred_probe_work_func
PC is at usb_del_gadget_udc+0x38/0xc4
LR is at __mutex_lock+0x31c/0xb18
...
Process kworker/0:1 (pid: 12, stack limit = 0x(ptrval))
Stack: (0xef121db0 to 0xef122000)
...
[<c076bf3c>] (usb_del_gadget_udc) from [<c0726bec>] (dwc2_hsotg_remove+0x10/0x20)
[<c0726bec>] (dwc2_hsotg_remove) from [<c0711208>] (dwc2_driver_probe+0x57c/0x69c)
[<c0711208>] (dwc2_driver_probe) from [<c06247c0>] (platform_drv_probe+0x6c/0xa4)
[<c06247c0>] (platform_drv_probe) from [<c0621df4>] (really_probe+0x200/0x48c)
[<c0621df4>] (really_probe) from [<c06221e8>] (driver_probe_device+0x78/0x1fc)
[<c06221e8>] (driver_probe_device) from [<c061fcd4>] (bus_for_each_drv+0x74/0xb8)
[<c061fcd4>] (bus_for_each_drv) from [<c0621b54>] (__device_attach+0xd4/0x16c)
[<c0621b54>] (__device_attach) from [<c0620c98>] (bus_probe_device+0x88/0x90)
[<c0620c98>] (bus_probe_device) from [<c06211b0>] (deferred_probe_work_func+0x3c/0xd0)
[<c06211b0>] (deferred_probe_work_func) from [<c0149280>] (process_one_work+0x234/0x7dc)
[<c0149280>] (process_one_work) from [<c014986c>] (worker_thread+0x44/0x51c)
[<c014986c>] (worker_thread) from [<c0150b1c>] (kthread+0x158/0x1a0)
[<c0150b1c>] (kthread) from [<c0100114>] (ret_from_fork+0x14/0x20)
Exception stack(0xef121fb0 to 0xef121ff8)
...
---[ end trace 9724c2fc7cc9c982 ]---
While fixing this also fix the double call to dwc2_lowlevel_hw_disable()
if dr_mode is set to USB_DR_MODE_PERIPHERAL. In such case low-level
hardware is already disabled before calling usb_add_gadget_udc(). That
function correctly preserves low-level hardware state, there is no need
for the second unconditional dwc2_lowlevel_hw_disable() call.
Fixes: 207324a321 ("usb: dwc2: Postponed gadget registration to the udc class driver")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Implement udc->pullup callback, so that udc_connect/disconnect work.
This is needed for composite gadget, as it assumes udc_disconnect()
actually works and calls its ->disconnect callback.
Acked-by: Cristian Birsan <cristian.birsan@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When binding an UDC driver to the pending gadget fails in
check_pending_gadget_drivers(), the usb_add_gadget_udc_release() function
ends without waiting for the usb_gadget_state_work to finish, what in
turn might cause the whole struct usb_gadget being freed by the caller
before the usb_gadget_state_work being executed.
This can be observed on some boards with USB Mass Storage gadget
compiled-in and kernel booted without the needed module parameters:
dwc2 12480000.hsotg: dwc2_check_params: Invalid parameter besl=1
dwc2 12480000.hsotg: dwc2_check_params: Invalid parameter g_np_tx_fifo_size=1024
dwc2 12480000.hsotg: EPs: 16, dedicated fifos, 7808 entries in SPRAM
Mass Storage Function, version: 2009/09/11
LUN: removable file: (no medium)
no file given for LUN0
g_mass_storage 12480000.hsotg: failed to start g_mass_storage: -22
dwc2: probe of 12480000.hsotg failed with error -22
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000004
pgd = (ptrval)
[00000004] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 1 PID: 88 Comm: kworker/1:2 Not tainted 5.8.0-rc5-next-20200715-00062-gc5bb489ae825-dirty #8792
Hardware name: Samsung Exynos (Flattened Device Tree)
Workqueue: 0x0 (rcu_gp)
PC is at process_one_work+0x44/0x7dc
...
Process kworker/1:2 (pid: 88, stack limit = 0x(ptrval))
Stack: (0xed9f1f00 to 0xed9f2000)
...
[<c0148590>] (process_one_work) from [<c0148d6c>] (worker_thread+0x44/0x51c)
[<c0148d6c>] (worker_thread) from [<c01500c0>] (kthread+0x158/0x1a0)
[<c01500c0>] (kthread) from [<c0100114>] (ret_from_fork+0x14/0x20)
Exception stack(0xed9f1fb0 to 0xed9f1ff8)
...
---[ end trace 5033c1326a62e5f3 ]---
note: kworker/1:2[88] exited with preempt_count 1
Fix this by flushing pending work in error path.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
- Delete the duplicated EP_CMD_ERDY and EP_CMD_REQ_CMPL setting
- Prepare the next setup before setting EP_CMD_ERDY and EP_CMD_REQ_CMPL,
it could avoid a bug that DMA hang at EP0 OUT for DEV_VER_NXP_V1
- Delete the duplicated cdns3_set_hw_configuration calling at
cdns3_req_ep0_set_configuration, the composite.c will handle
this request, and call .ep0_queue back, and at .ep_queue it will
call cdns3_set_hw_configuration.
- Move cdns3_allow_enable_l1 into cdns3_set_hw_configuration since
it is part of this function.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The reset is a shared reset line, but reset_control_reset is still used
and reset_control_deassert is not guaranteed to have been called before
the first reset_control_assert call. When suspending the following
warning may be seen:
WARNING: CPU: 1 PID: 5530 at drivers/reset/core.c:355 reset_control_assert+0x184/0x19c
Hardware name: Hardkernel ODROID-N2 (DT)
[..]
pc : reset_control_assert+0x184/0x19c
lr : dwc3_meson_g12a_suspend+0x68/0x7c
[..]
Call trace:
reset_control_assert+0x184/0x19c
dwc3_meson_g12a_suspend+0x68/0x7c
platform_pm_suspend+0x28/0x54
__device_suspend+0x590/0xabc
dpm_suspend+0x104/0x404
dpm_suspend_start+0x84/0x1bc
suspend_devices_and_enter+0xc4/0x4fc
pm_suspend+0x198/0x2d4
Fixes: 6d9fa35a34 ("usb: dwc3: meson-g12a: get the reset as shared")
Signed-off-by: Dan Robertson <dan@dlrobertson.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If a tracee is uprobed and it hits int3 inserted by debugger, handle_swbp()
does send_sig(SIGTRAP, current, 0) which means si_code == SI_USER. This used
to work when this code was written, but then GDB started to validate si_code
and now it simply can't use breakpoints if the tracee has an active uprobe:
# cat test.c
void unused_func(void)
{
}
int main(void)
{
return 0;
}
# gcc -g test.c -o test
# perf probe -x ./test -a unused_func
# perf record -e probe_test:unused_func gdb ./test -ex run
GNU gdb (GDB) 10.0.50.20200714-git
...
Program received signal SIGTRAP, Trace/breakpoint trap.
0x00007ffff7ddf909 in dl_main () from /lib64/ld-linux-x86-64.so.2
(gdb)
The tracee hits the internal breakpoint inserted by GDB to monitor shared
library events but GDB misinterprets this SIGTRAP and reports a signal.
Change handle_swbp() to use force_sig(SIGTRAP), this matches do_int3_user()
and fixes the problem.
This is the minimal fix for -stable, arch/x86/kernel/uprobes.c is equally
wrong; it should use send_sigtrap(TRAP_TRACE) instead of send_sig(SIGTRAP),
but this doesn't confuse GDB and needs another x86-specific patch.
Reported-by: Aaron Merey <amerey@redhat.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200723154420.GA32043@redhat.com
Since the default_wake_function() passes its flags onto
try_to_wake_up(), warn if those flags collide with internal values.
Given that the supplied flags are garbage, no repair can be done but at
least alert the user to the damage they are causing.
In the belief that these errors should be picked up during testing, the
warning is only compiled in under CONFIG_SCHED_DEBUG.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: https://lore.kernel.org/r/20200723201042.18861-1-chris@chris-wilson.co.uk
Sealevel XR17V35X based devices are inoperable on kernel versions
4.11 and above due to a change in the GPIO preconfiguration introduced in
commit
7dea8165f1. This patch fixes this by preconfiguring the GPIO on Sealevel
cards to the value (0x00) used prior to commit 7dea8165f1
With GPIOs preconfigured as per commit 7dea8165f1 all ports on
Sealevel XR17V35X based devices become stuck in high impedance
mode, regardless of dip-switch or software configuration. This
causes the device to become effectively unusable. This patch (in
various forms) has been distributed to our customers and no issues
related to it have been reported.
Fixes: 7dea8165f1 ("serial: exar: Preconfigure xr17v35x MPIOs as output")
Signed-off-by: Matthew Howell <matthew.howell@sealevel.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2007221605270.13247@tstest-VirtualBox
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for net:
1) Fix NAT hook deletion when table is dormant, from Florian Westphal.
2) Fix IPVS sync stalls, from guodeqing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
geneve_nl2info() sets 'df' conditionally, so we have to
initialize it by copying the value from existing geneve
device in geneve_changelink().
Fixes: 56c09de347 ("geneve: allow changing DF behavior after creation")
Reported-by: syzbot+7ebc2e088af5e4c0c9fa@syzkaller.appspotmail.com
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Very similar to commit 544f287b84
("bonding: check error value of register_netdevice() immediately"),
we should immediately check the return value of register_netdevice()
before doing anything else.
Fixes: 005db31d5f ("bonding: set carrier off for devices created through netlink")
Reported-and-tested-by: syzbot+bbc3a11c4da63c1b74d6@syzkaller.appspotmail.com
Cc: Beniamino Galvani <bgalvani@redhat.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 9ffad9263b.
Upon additional testing with older servers, it was found that
the original commit introduced a regression when using the old SMB1
dialect and rsyncing over an existing file.
The patch will need to be respun to address this, likely including
a larger refactoring of the SMB1 and SMB3 rename code paths to make
it less confusing and also to address some additional rename error
cases that SMB3 may be able to workaround.
Signed-off-by: Steve French <stfrench@microsoft.com>
Reported-by: Patrick Fernie <patrick.fernie@gmail.com>
CC: Stable <stable@vger.kernel.org>
Acked-by: Ronnie Sahlberg <lsahlber@redhat.com>
Acked-by: Pavel Shilovsky <pshilov@microsoft.com>
Acked-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
to reflect reality and avoid further confusion. This is a user space
visible change therefore the commit has also a stable tag for 5.7,
where this counter was introduced.
- Add Matthew Rosato as s390 IOMMU maintainer.
-----BEGIN PGP SIGNATURE-----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=9JBZ
-----END PGP SIGNATURE-----
Merge tag 's390-5.8-6' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux into master
Pull s390 fixes from Heiko Carstens:
- Change cpum_cf/perf counter name from DFLT_CCERROR to DFLT_CCFINISH
to reflect reality and avoid further confusion. This is a user space
visible change therefore the commit has also a stable tag for 5.7,
where this counter was introduced.
- Add Matthew Rosato as s390 IOMMU maintainer.
* tag 's390-5.8-6' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
MAINTAINERS: add Matthew for s390 IOMMU
s390/cpum_cf,perf: change DFLT_CCERROR counter name
When I have KASAN enabled on my kernel and I start stressing the
touchscreen my system tends to hang. The touchscreen is one of the
only things that does a lot of big i2c transfers and ends up hitting
the DMA paths in the geni i2c driver. It appears that KASAN adds
enough delay in my system to tickle a race condition in the DMA setup
code.
When the system hangs, I found that it was running the geni_i2c_irq()
over and over again. It had these:
m_stat = 0x04000080
rx_st = 0x30000011
dm_tx_st = 0x00000000
dm_rx_st = 0x00000000
dma = 0x00000001
Notably we're in DMA mode but are getting M_RX_IRQ_EN and
M_RX_FIFO_WATERMARK_EN over and over again.
Putting some traces in geni_i2c_rx_one_msg() showed that when we
failed we were getting to the start of geni_i2c_rx_one_msg() but were
never executing geni_se_rx_dma_prep().
I believe that the problem here is that we are starting the geni
command before we run geni_se_rx_dma_prep(). If a transfer makes it
far enough before we do that then we get into the state I have
observed. Let's change the order, which seems to work fine.
Although problems were seen on the RX path, code inspection suggests
that the TX should be changed too. Change it as well.
Fixes: 37692de5d5 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Mukesh Kumar Savaliya <msavaliy@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
On R-Car Gen2, we get a timeout when reading from the address set in
ICSAR, even though the slave interface is disabled. Clearing it fixes
this situation. Note that Gen3 is not affected.
To reproduce: bind and undbind an I2C slave on some bus, run
'i2cdetect' on that bus.
Fixes: de20d1857d ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Previously TLP may send multiple probes of new data in one
flight. This happens when the sender is cwnd limited. After the
initial TLP containing new data is sent, the sender receives another
ACK that acks partial inflight. It may re-arm another TLP timer
to send more, if no further ACK returns before the next TLP timeout
(PTO) expires. The sender may send in theory a large amount of TLP
until send queue is depleted. This only happens if the sender sees
such irregular uncommon ACK pattern. But it is generally undesirable
behavior during congestion especially.
The original TLP design restrict only one TLP probe per inflight as
published in "Reducing Web Latency: the Virtue of Gentle Aggression",
SIGCOMM 2013. This patch changes TLP to send at most one probe
per inflight.
Note that if the sender is app-limited, TLP retransmits old data
and did not have this issue.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently added some bounds checking in ax25_connect() and
ax25_sendmsg() and we so we removed the AX25_MAX_DIGIS checks because
they were no longer required.
Unfortunately, I believe they are required to prevent integer overflows
so I have added them back.
Fixes: 8885bb0621 ("AX.25: Prevent out-of-bounds read in ax25_sendmsg()")
Fixes: 2f2a7ffad5 ("AX.25: Fix out-of-bounds read in ax25_connect()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit adc0daad36 ("dm: report suspended
device during destroy") broke integrity recalculation.
The problem is dm_suspended() returns true not only during suspend,
but also during resume. So this race condition could occur:
1. dm_integrity_resume calls queue_work(ic->recalc_wq, &ic->recalc_work)
2. integrity_recalc (&ic->recalc_work) preempts the current thread
3. integrity_recalc calls if (unlikely(dm_suspended(ic->ti))) goto unlock_ret;
4. integrity_recalc exits and no recalculating is done.
To fix this race condition, add a function dm_post_suspending that is
only true during the postsuspend phase and use it instead of
dm_suspended().
Signed-off-by: Mikulas Patocka <mpatocka redhat com>
Fixes: adc0daad36 ("dm: report suspended device during destroy")
Cc: stable vger kernel org # v4.18+
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
IOSQE_ASYNC branch of io_queue_sqe() is another place where an
unitialised req->work can be accessed (i.e. prior io_req_init_async()).
Nothing really bad though, it just looses IO_WQ_WORK_CONCURRENT flag.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
dbc should not be aware of, or use any dbctty specific variables.
currenly dbc driver reads the port->registered flag to see if the
callbacks should be called.
Only makes these decisions based on dbc internal state instead.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-27-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't call dbctty driver functions directly from dbc core code.
Introduce a new dbc_driver structure that contains function pointers
for disconnect and configure operations.
The driver (ttydbc) must provide these opeations when creating a dbc.
Name the structure dbc_driver instead of dbc_ops as we plan to
add more driver configureable values here, such as vid and pid.
Decouples dbc and dbctty.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-26-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split the dbc tty driver registrations function into separate
init and probe parts.
The init part will register the tty driver, and should in the future be
called from module_init().
The probe part will become the normal probe function, but for now it is
called from the init part.
The unregister function is s likewise split into remove and exit parts.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-25-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't pass endpoint pointer, dbctty should not be aware of
struct dbc_ep, knowing the direction is enough.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-23-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_dbc_start() and xhci_dbc_stop() functions only used xhci_hcd pointer
to get the dbc pointer.
Pass the dbc pointer instead of the xhci_hcd pointer as a parameter
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-22-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dbc mem_init and mem_cleanup functions used xhci_hcd to get to the device
pointer. The device pointer can be accessed directly from dbc structure,
so pass a pointer to dbc as a parameter instead.
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-21-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generic xhci ring allocations code needs struct xhci_hcd pointer, and
it allocates memory for the rings from dma pools created for the xhci
device.
In order to decouple xhci and DbC we have to create our own ring allocation
and free routines for DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DbC context is different from the xhci device context.
It's a lot smaller as it only contains three 64 bytes sub-contexts;
the info, endpoint-out, and endpoint-in contexts. In total 192 bytes.
The context size (CSZ) field in HCCPARAMS1 xhci register does not alter
DbC context size like it does for xhci device contexts.
So don't use the geneic xhci context memory allocation, or the
dma pool that is intended for xhci device contexts.
In addition to saving memory this also helps decoupleing xhci and dbc code.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dbc request completion callback doesn't need a xhci_hcd pointer.
The only user of the xhci_hcd pointer in dbgtty request callback was
the xhci_warn() function. Change it to dev_warn() instead.
While changing the callback function parameter to dbc in struct
xhci_requeset, move the struct xhci_request declaraion down a bit in the
header file to avoid compiler warinings
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass dbc pointer instead of struct xhci_hcd pointer to the get_in_ep() and
get_out_ep() helper functions.
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-17-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass dbc pointer to the xhci_dbc_tty_register_device() and
xhci_dbc_tty_unregister_device() functions instead of xhci_hcd pointer
These functions don't need a xhci_hcd pointer anymore, only use case was
the xhci_err() function, which is now changed to a dev_err() instead.
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The event handling function only used xhci pointer to get the dbc pointer.
Pass the dbc pointer instead as a parameter
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass the dbc pointer instead of xhci_hcd pointer in order to
decouple xhci and dbc.
xhci_do_dbc_stop() only used xhci to get the dbc pointer.
Pass the dbc pointer instead as a parameter
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-14-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct xhci_hcd pointer is not needed for dbc endpoint init and exit,
it was only used to get to the dbc structure.
Pass the dbc pointer as a parameter to these functions instead.
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbc_ep_do_queue() can now get the device pointer directly from dbc
structure instead of going through the xhci_hcd structure.
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_write_64() is essentially a wrapper for lo_hi_writeq(), but it
requires struct xhci_hcd * as a parameter.
Use lo_hi_writeq() directly instead
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To make this change possible we also need to change
dbc_handle_port_status() to take dbc pointer as parameter instead of
xhci_hcd pointer.
Note that xhci_info() used xhci_to_hcd(xhci)->self.controller as the
device while for dev_info we use xhci_to_hcd(xhci)->self.sysdev.
In many cases those are the same, but not for some device where
a dwc3 controller creates a xhci platform device. In th this case
self.controller may be the platform device while self.sysdev is
the actual device known to firmware (dwc3).
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the dbc structure contains a pointer to struct xhci_hcd,
and dbc functions use that to dig up the underlying device pointer.
We are trying to decouple xhci and dbc code, and prepare for
code that use dbc such as dbctty into into real device drivers.
This is one step along the way.
Keep functionality the same and keep the xhci pointer, and
let the new device pointer point to the xhci device for now.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbc_dma_free_coherent() takes struct xhci_hcd pointer as a parameter, but
does nothing more than calls dma_free_coherent().
Remove it and call dma_free_coherent() directly instead.
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbc_dma_alloc_coherent() takes struct xhci_hcd pointer as an parameter, but
does nothing more than calls dma_alloc_coherent().
Remove it and call dma_alloc_coherent() directly instead.
No functional changes
This change helps decoupling xhci and DbC
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200723144530.9992-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
