Replace the mac_filter_list with a static size hash table of 8bits. The
primary advantage of this is a decrease in latency of operations related
to searching for specific MAC filters, including .set_rx_mode. Using
a linked list resulted in several locations which were O(n^2). Using
a hash table should give us latency growth closer to O(n*log(n)).
Change-ID: I5330bd04053b880e670210933e35830b95948ebb
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
When inside a loop where we call i40e_del_filter we use an O(n^2)
pattern where i40e_del_filter calls i40e_find_filter for us. We can
avoid this O(n^2) logic by factoring a function, __i40e_del_filter() out
from the i40e_del_filter code. This allows us to re-use the delete logic
where appropriate without having to search for the filter twice.
This new function benefits several functions including i40e_vsi_add_vlan,
i40e_vsi_kill_vlan, i40e_del_mac_vlan_all, and i40e_vsi_release.
Change-ID: I75fabe0f53bf73f56b80d342e5fdcfcc28f4d3eb
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When adding new MAC address filters, the driver determines if it should
behave in VLAN mode (where all MAC addresses get assigned to every
existing VLAN) or in non-VLAN mode where MAC addresses get assigned the
VLAN_ANY identifier. Under some circumstances it is possible that a VLAN
has been marked for removal (such that all filters of that VLAN are set
to I40E_FILTER_REMOVE), and a subsequent call to i40e_put_mac_in_vlan
may occur prior to the driver subtask that syncs filters to the
hardware.
In this case, we may add filters to the new removed VLAN, even though it
should have been removed. This is most obvious when first adding a new
VLAN. We will delete all filters which are in I40E_VLAN_ANY (-1) and
then re-add them as in VLAN 0 (untagged). Then before we sync filters,
we will add new MAC address filter, which will be added to every VLAN
that exists. Unfortunately, this will include I40E_VLAN_ANY, so we will
end up incorrectly adding filters to the -1 VLAN. This can be fixed by
simply skipping all filters which are marked for removal.
A similar check is not necessary in i40e_del_mac_all_vlan, since we are
deleting, and any filter which we find already marked for removal would
simply be deleted again, which doesn't cause any issues.
Change-Id: I7962154013ce02fe950584690aeeb3ed853d0086
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a PVID has been assigned to a VSI, the function
i40e_put_mac_in_vlan arbitrarily modifies all filters
to have the same VLAN. This is obviously incorrect
because it could be modifying active filters without
putting them into the NEW state. The correct method
is to remove then re-add filters which is already done
in the code where we assign the PVID.
Fix this issue and a few other minor nits at the same
time. First, when we have a PVID don't even bother
looping and simply add the filter with the PVID immediately.
In the case of the loop, we now can remove several checks.
We also don't need to use i40e_find_filter first before
calling i40e_add_filter, since i40e_add_filter implicitly
does a lookup already.
Finally, update the return semantics of this function so
that on failure to add a filter it returns NULL, but on
success, it returns the last filter added. Otherwise,
we're just returning the last filter in the list. An
alternative fix might be to return 0 or an error code,
but this is pretty invasive to every call site.
Change-ID: I2325dfd843aec76d89fb0d7cb0e7c4f290a34840
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A future patch will be modifying these functions and making a call to
a static function which currently is defined after these functions. Move
them in a separate patch to ease review and ensure the moved code is
correct.
Change-ID: I2ca7fd4e10c0c07ed2291db1ea41bf5987fc6474
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The kernel provides __dev_uc_sync and __dev_mc_sync in order for drivers
which need individual notification of add and delete for each filter.
These functions allow us to vastly simplify our .set_rx_mode handler. We
need to implement two functions for sync and unsync which add and remove
filters respectively.
This change avoids a very complex and inefficient algorithm which
resulted in an abnormal latency for the .set_rx_mode NDO operation. The
resulting code after this change is more readable, more efficient, and
less code.
Due to the callback signature used by these functions we also must
update several other functions to take a const u8 * pointer.
Change-Id: I2ca7fd4e10c0c07ed2291db1ea41bf5987fc6474
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Originally the is_vf and is_netdev fields were added in order to
distinguish between VF and netdev filters in a single VSI. However, it
can be noted that we use separate VSI for SRIOV VFs and for netdev VSI.
Thus, since a single VSI should only ever have one type of filter, we
can simply remove the checks and remove the typing.
In a similar fashion, we can note that the only remaining way to get
multiple filters of a single type is through a debug command that was
added to debugfs. This command is useless in practice, and results in
causing bugs if we keep counter tracking but lose the is_vf and
is_netdev protections as desired above.
Since the only time we'd actually have a counter value besides 0 and
1 is through use of this debugfs hook, we can remove this unnecessary
command, and the entire counter logic it required.
We vastly simplify mac filters by removing
(a) the distinction between VF and netdev filters
(b) counting logic
(c) the ability to add and remove filters bypassing the stack via debugfs
Change-ID: Idf916dd2a1159b1188ddbab5bef6b85ea6bf27d9
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
So the i40e driver had a really convoluted configuration for how to handle
the debug flags contained in msg_level. Part of the issue is that the
driver has its own 32 bit mask that it was using to track a separate set of
debug features. From what I can tell it was trying to use the upper 4 bits
to determine if the value was meant to represent a bit-mask or the numeric
value provided by debug level.
What this patch does is clean this up by compressing those 4 bits into bit
31, as a result we just have to perform a check against the value being
negative to determine if we are looking at a debug level (positive), or a
debug mask (negative). The debug level will populate the msg_level, and
the debug mask will populate the debug_mask in the hardware struct.
I added similar logic for ethtool. If the value being provided has bit 31
set we assume the value being provided is a debug mask, otherwise we assume
it is a msg_enable mask. For displaying we only provide the msg_enable,
and if debug_mask is in use we will print it to the dmesg log.
Lastly I removed the debugfs interface. It is redundant with what we
already have in ethtool and really doesn't belong anyway.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Patch a036244c06 "i40e: Fix kernel panic on enable/disable LLDP"
introduced an error in bit logic.
Originally this bit manipulation was meant to clear two bits to indicate
that DCB was not enabled or capable. An "&" was incorrectly used instead
of an "|" bit operator to combine the two bitmasks into one. This also
created a static checker error since the resultant code was a no-op.
This patch fixes the error by using the correct bit-wise operator.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is code refactoring. This patch removes the workaround which deleted
a default MAC filter added by the firmware when the interface was brought
up. This filter caused frames to pass disregarding the VLAN tagging.
It used to be automatically applied after reset in pre-SRA FW versions.
This workaround is not needed in production NICs and hence can be removed.
Change-ID: I129fe1aae1f17b5a224c9b29a996d916aa1be1ec
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ethtool -L option with the combined parameter is for changing the number of
multi-purpose channels of the specified network device. The pre-set maximum
for the combined channels is cpu dependent. Currently, for an i40e device,
when the user sets a value between 64 and the maximum that the cpu can
support for the combined parameter, the i40e driver displays the confusing
info in dmesg to only show 64 as the RSS count regardless of what the
accepted user input is as long as it is larger than 64.
This patch fixes the message in the i40e driver when the user uses
ethtool -L to change the number of the combined channels to consistently
display the user requested value if it is valid and accepted by ethtool.
Change-ID: Ia80a68bc844b779a49e0f76e7d3dcc915032d9af
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There exists a bug in which a 'perfect storm' can occur and cause
interrupts to fail to be correctly affinitized. This causes unexpected
behavior and has a substantial impact on performance when it happens.
The bug occurs if there is heavy traffic, any number of CPUs that have
an i40e interrupt are pegged at 100%, and the interrupt afffinity for
those CPUs is changed. Instead of moving to the new CPU, the interrupt
continues to be polled while there is heavy traffic.
The bug is most readily realized as the driver is first brought up and
all interrupts start on CPU0. If there is heavy traffic and the
interrupt starts polling before the interrupt is affinitized, the
interrupt will be stuck on CPU0 until traffic stops. The bug, however,
can also be wrought out more simply by affinitizing all the interrupts
to a single CPU and then attempting to move any of those interrupts off
while there is heavy traffic.
This patch fixes the bug by registering for update notifications from
the kernel when the interrupt affinity changes. When that fires, we
cache the intended affinity mask. Then, while polling, if the cpu is
pegged at 100% and we failed to clean the rings, we check to make sure
we have the correct affinity and stop polling if we're firing on the
wrong CPU. When the kernel successfully moves the interrupt, it will
start polling on the correct CPU. The performance impact is minimal
since the only time this section gets executed is when performance is
already compromised by the CPU.
Change-ID: I4410a880159b9dba1f8297aa72bef36dca34e830
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Order of arguments is wrong.
The wrong code has been introduced by commit 7d4f8d871a, but is compiled
only since commit 9df70b6641.
Note that this may break netlink dumps.
Fixes: 9df70b6641 ("i40e: Remove incorrect #ifdef's")
Fixes: 7d4f8d871a ("switchdev; add VLAN support for port's bridge_getlink")
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Huaibin Wang <huaibin.wang@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If we fail on allocating enough MSI-X interrupts, we should disable
them since they were previously enabled in this point of code.
Not disabling them can lead to WARN_ON() being triggered and subsequent
failure in enabling MSI as a fallback; the below message was shown without
this patch while we played with interrupt allocation in i40e driver:
[ 21.461346] sysfs: cannot create duplicate filename '/devices/pci0007:00/0007:00:00.0/0007:01:00.3/msi_irqs'
[ 21.461459] ------------[ cut here ]------------
[ 21.461514] WARNING: CPU: 64 PID: 1155 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x88/0xc0
Also, we noticed that without this patch, if we modprobe the module without
enough MSI-X interrupts (triggering the above warning), unload the module
and re-load it again, we got a crash on the system.
Signed-off-by: Guilherme G Piccoli <gpiccoli@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
in commit a036244c06 a fix
was put into place to avoid a kernel panic when a non-
supported traffic class configuration was put into place
and then lldp was enabled/disabled on the link partner
switch. This fix caused it to be necessary to
unload/reload the driver to reenable DCB once a supported
TC config was in place.
The root cause of the original panic was that the function
i40e_pf_get_default_tc was allowing for a default TC other
than TC 0, and only TC 0 is supported as a default.
This patch removes the get_default_tc function and replaces
it with a #define since there is only one TC supported as
a default.
Change-Id: I448371974e946386d0a7718d73668b450b7c72ef
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Ronald Bynoe <ronald.j.bynoe@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e100: min_mtu 68, max_mtu 1500
- remove e100_change_mtu entirely, is identical to old eth_change_mtu,
and no longer serves a purpose. No need to set min_mtu or max_mtu
explicitly, as ether_setup() will already set them to 68 and 1500.
e1000: min_mtu 46, max_mtu 16110
e1000e: min_mtu 68, max_mtu varies based on adapter
fm10k: min_mtu 68, max_mtu 15342
- remove fm10k_change_mtu entirely, does nothing now
i40e: min_mtu 68, max_mtu 9706
i40evf: min_mtu 68, max_mtu 9706
igb: min_mtu 68, max_mtu 9216
- There are two different "max" frame sizes claimed and both checked in
the driver, the larger value wasn't relevant though, so I've set max_mtu
to the smaller of the two values here to retain identical behavior.
igbvf: min_mtu 68, max_mtu 9216
- Same issue as igb duplicated
ixgb: min_mtu 68, max_mtu 16114
- Also remove pointless old == new check, as that's done in dev_set_mtu
ixgbe: min_mtu 68, max_mtu 9710
ixgbevf: min_mtu 68, max_mtu dependent on hardware/firmware
- Some hw can only handle up to max_mtu 1504 on a vf, others 9710
CC: netdev@vger.kernel.org
CC: intel-wired-lan@lists.osuosl.org
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although rare, it's possible to hit PCI error early on device
probe, meaning possibly some structs are not entirely initialized,
and some might even be completely uninitialized, leading to NULL
pointer dereference.
The i40e driver currently presents a "bad" behavior if device hits
such early PCI error: firstly, the struct i40e_pf might not be
attached to pci_dev yet, leading to a NULL pointer dereference on
access to pf->state.
Even checking if the struct is NULL and avoiding the access in that
case isn't enough, since the driver cannot recover from PCI error
that early; in our experiments we saw multiple failures on kernel
log, like:
[549.664] i40e 0007:01:00.1: Initial pf_reset failed: -15
[549.664] i40e: probe of 0007:01:00.1 failed with error -15
[...]
[871.644] i40e 0007:01:00.1: The driver for the device stopped because the
device firmware failed to init. Try updating your NVM image.
[871.644] i40e: probe of 0007:01:00.1 failed with error -32
[...]
[872.516] i40e 0007:01:00.0: ARQ: Unknown event 0x0000 ignored
Between the first probe failure (error -15) and the second (error -32)
another PCI error happened due to the first bad probe. Also, driver
started to flood console with those ARQ event messages.
This patch will prevent these issues by allowing error recovery
mechanism to remove the failed device from the system instead of
trying to recover from early PCI errors during device probe.
CC: <stable@vger.kernel.org>
Signed-off-by: Guilherme G Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if the MSI-X vector limit is reached the sideband flow
director gets disabled. A bit too early to make that decision, as
vectors may get re-distributed. So move the check further back.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver allocates 1 vector per CPU thread and the current hardware
limit for vectors is 129 per PF. On systems with 128 or more threads
this currently means all vectors are used by the PF leaving no room for
additional features like VMDq, iWARP, etc...
The code that should redistribute the vectors in this case is broken and
never triggers. Fixed the code so that it actually triggers if the
hardware limit is reached and adjust the number of queue pairs
accordingly.
Also the number of initially requested iWARP vectors was not properly
saved when the vector limit was reached, and therefore always zero.
Comparison with debug statement.
Before:
i40e 0000:2d:00.0: VMDq disabled, not enough MSI-X vectors
i40e 0000:2d:00.0: IWARP disabled, not enough MSI-X vectors
i40e 00.0 MSI-X vector distribution: PF 128, VMDq 0, FDSB 0, iWARP 0
After:
i40e 0000:2d:00.0: MSI-X vector limit reached, attempting to redistribute vectors
i40e 00.0 MSI-X vector distribution: PF 78, VMDq 8, FDSB 0, iWARP 42
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During MSI-X vector allocation for VMDq, a check for "no vectors left"
was missing, add it. This prevents more vectors to be allocated than
available.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some rare cases, we might get a VSI with no queues. In this case, we
cannot configure RSS on this VSI as it will try to divide by zero when
configuring the lookup table.
Change-ID: I6ae173a7dd3481a081e079eb10eb80275de2adb0
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The return value from i40e_shutdown_adminq() is always 0
(I40E_SUCCESS). So, the test for non-0 will never be true. Cleanup
by removing the test and debug print statement.
Change-ID: Ie51e8e37515c3e3a6a9ff26fa951d0e5e24343c1
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In i40e_fdir_check_and_reenable(), the driver performs some checks to
determine whether it is safe to re-enable FD Sideband and FD ATR
support. The current check will only determine if there is available
space in the flow director table. However, this ignores the fact that
ATR should be disabled when there are TCP/IPv4 sideband rules in effect.
Add the missing check, and update the info message printed when
I40E_DEBUG_FD is enabled.
Change-ID: Ibb9c63e5be95d63c53a498fdd5dbf69f54a00e08
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some locations that disable ATR accidentally used the "full" disable by
disabling the flag in the standard flags field. This incorrectly forces
ATR off permanently instead of temporarily disabling it. In addition,
some code locations accidentally set the ATR flag enabled when they only
meant to clear the auto_disable_flags. This results in ignoring the
user's ethtool private flag settings.
Additionally, when disabling ATR via ethtool, we did not perform a flush
of the FD table. This results in the previously assigned ATR rules still
functioning which was not expected.
Cleanup all these areas so that automatic disable uses only the
auto_disable_flag. Fix the flush code so that we can trigger a flush
even when we've disabled ATR and SB support, as otherwise the flush
doesn't work. Fix ethtool setting to actually request a flush. Fix
NETIF_F_NTUPLE flag to only clear the auto_disable setting and not
enable the full feature.
Change-ID: Ib2486111f8031bd16943e9308757b276305c03b5
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There exists a bug in which deleting a mac filter does not actually
occur. The driver reports that the filter has been deleted with no
error. The problem occurs because the wrong cmd_flag is passed to the
firmware when deleting the filter. The firmware reports an error back
to the driver but it is expressly ignored.
This fixes the bug by using the correct flag when deleting a filter.
Without this patch, deleted filters remain in firmware and function as
if they had not been deleted.
Change-ID: I5f22b874f3b83f457702f18f0d5602ca21ac40c3
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the problem where driver shows 100 Mbps as a supported speed,
and allows it to be configured for advertising on X722 devices. This patch
fixes the problem by not setting the 100 Mbps SGMII flag for X722 devices.
Without this patch, the user incorrectly thinks that 100 Mbps is supported
and hence might try to advertise it on X722 devices when it is actually not
a supported speed.
Change-ID: I8c3d7c4251a9402d98994ed29749b7b895a0f205
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue where we were byte swapping the port
parameter, then byte swapping it again in function execution.
Obviously, that's unnecessary, so take it out of the function calls.
Without this patch, the udp based tunnel configuration would
not be correct.
Change-ID: I788d83c5bd5732170f1a81dbfa0b1ac3ca8ea5b7
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, when using ethtool to change the RSS hash key, ethtool would
report back saying the old key was still being used and no error was
reported. It was unclear whether it was being reported incorrectly or
being set incorrectly. Debugging revealed 'i40e_set_rxfh()' returned
zero immediately instead of setting the key because a user defined
indirection table is not supplied when changing the hash key.
This fix instead changes it such that if an indirection table is not
supplied, then a default one is created and the hash key is now
correctly set.
Change-ID: Iddb621897ecf208650272b7ee46702cad7b69a71
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
If DCB is configured on the link partner switch with an
unsupported traffic class configuration (e.g. non-contiguous TCs),
the driver is flagging DCB as disabled. But, for future DCB
LLDPDUs, the driver was checking if the interface was DCB capable
instead of enabled. This was causing a kernel panic when LLDP
was enabled/disabled on the link partner switch.
This patch corrects the situation by having the LLDP event handler
check the correct flag in the pf structure. It also cleans up the
setting and clearing of the enabled flag for other checks.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes a common flow for Client instance open during init
and reset path. The Client subtask can handle both the cases instead of
making a separate notify_client_of_open call.
Also it may fix a bug during reset where the service task was leaking
some memory and causing issues.
Change-Id: I7232a32fd52b82e863abb54266fa83122f80a0cd
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace calls to create_singlethread_workqueue instead with alloc_workqueue
as is style with other Intel drivers. This provides more control over
workqueue creation, and allows explicit setting of the desired mode of
operation. It also makes it more obvious that driver name constant is
passed to a format "%s".
Change-ID: I6192b44caf5140336cd54c5b350d51c73b541fdb
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous refactor added support to store user configuration for VSIs,
so that extra VSIs such as for VMDq can use this information when
configuring. Unfortunately the i40e_vsi_config_rss function was missed
in this refactor, and the values were being ignored. Fix this by
checking for the fields and using those instead of always using the
default values.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move this function below the two functions related to configuring RSS
via the admin queue. This helps co-locate the two functions, and made it
easier to spot a bug in the first i40e_config_rss_aq function as
compared to the i40e_get_rss_aq function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the bug which causes RSS to continue to work
after being disabled. After disabling RSS, traffic would continue
to be assigned to different queues instead of falling back to a
single queue. Without this patch, attempting to disable RSS would
not work as expected. This patch fixes the bug by clearing the
lookup table used by RSS such that all traffic is assigned to a
single queue. This patch also addresses the issue of reinstating
the lookup table should RSS then be re-enabled.
Change-ID: Ib20c7c6a7e9f1f772bb787370f8a8c664796b141
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where a static analysis tool generates
a warning for "INVARIANT_CONDITION: Expression 'enabled_tc' used
in the condition always yields the same result."
Without this patch, the driver will not pass the static analysis
tool checks without generating warnings.
This patch fixes the problem by eliminating the irrelevant check
and redundant assignment for the value of enabled_tc.
Change-ID: Ia7d44cb050f507df7de333e96369d322e08bf408
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we are resetting the pf stats we should also reset the RX csum
error stat.
Change-ID: I7af5ee0ec81a10f6deee1a7b8c2082ea068ef620
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver was causing a kernel panic when
non-contiguous Traffic Classes, or Traffic Classes not
starting with TC0, were configured on a link partner switch.
i40e does not support non-contiguous TCs.
To fix this, the patch changes the logic when determining
the total number of TCs enabled. Before, this would use the
highest TC number enabled and assume that all TCs below it were
also enabled. Now, we create a bitmask of enabled TCs and scan
it to determine not only the number of TCs, but also if the set
of enabled TCs starts at zero and is contiguous. If not, then
DCB is disabled by only returning one TC.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-07-22
This series contains updates to i40e and i40evf.
Heinrich Schuchardt found a possible null pointer being dereferenced in
i40e_debug_aq(), fixed the issue by doing the variable assignment after
we are sure the pointer is not null.
Avinash fixed an issue when link was down, we were not showing the
correct advertised link modes.
Mitch cleans up a useless initializer since the variable is assigned
right away. Refactors the receive filter handling to properly track
filter adds and deletes so the driver will not lose filters during a
reset and up/down cycles. Also added a tracking mechanism so that the
driver knows when to enter and leave promiscuous mode.
Catherine removes a device id which is not needed (or used). Moves
a mutex lock since we need to lock the client list around the
i40e_client_release() call to prevent the release from interrupting
the client instances while they are being added.
Joshua adds Hyper-V specific VF device ids.
Amitoj Kaur Chawla cleans up a redundant memset() call before a memcpy().
Stefan Assmann adds the missing link advertise for some x710 NICs.
Tushar Dave fixes and issue found on SPARC, where a PF reset clears MAC
filters and if a platform-specific MAC address is used, the driver has
to explicitly write default MAC address to MAC filters otherwise all
incoming traffic destined to the default MAC address will be dropped
after reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
i40e PF reset clears mac filters. If platform-specific mac address
is used, driver has to explicitly write default mac address to mac
filters otherwise all incoming traffic destined to default mac
address will be dropped after reset.
This issue was found on SPARC while toggling i40e ntuple via ethtool.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove redundant call to memset before a call to memcpy.
The Coccinelle semantic patch used to make this change is as follows:
@@
expression e1,e2,e3,e4;
@@
- memset(e1,e2,e3);
memcpy(e1,e4,e3);
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Properly track filter adds and deletes so the driver doesn't lose filters
during resets and up/down cycles. Add a tracking mechanism so that the
driver knows when to enter and leave promiscuous mode.
Implement a simple state machine so the driver can track the status of
each filter throughout its lifecycle. Properly manage the overflow promiscuous
state for the each VSI, and provide a way for the driver to detect when to exit
overflow promiscuous mode.
Remove all possible default MAC filters that the firmware may have set up so
that the driver can manage these correctly, particularly when VLANs come into
play. Remove the LAA flag for filters; instead just send whatever we get through
set_mac to the firmware as the LAA for wakeup purposes.
Finally, add the state of each filter to debugfs output so we can see what's
going on inside the driver's pointy little head.
Change-ID: I97c5e366fac2254fa01eaff4f65c0af61dcf2e1f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This device ID is not needed, so take it out.
Change-ID: I148d29f68a1f58b03980ecd83047a1b440f4f74d
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, the q_vector initialization routine sets the affinity_mask
of a q_vector based on v_idx value. Meaning a loop iterates on v_idx,
which is an incremental value, and the cpumask is created based on
this value.
This is a problem in systems with multiple logical CPUs per core (like in
SMT scenarios). If we disable some logical CPUs, by turning SMT off for
example, we will end up with a sparse cpu_online_mask, i.e., only the first
CPU in a core is online, and incremental filling in q_vector cpumask might
lead to multiple offline CPUs being assigned to q_vectors.
Example: if we have a system with 8 cores each one containing 8 logical
CPUs (SMT == 8 in this case), we have 64 CPUs in total. But if SMT is
disabled, only the 1st CPU in each core remains online, so the
cpu_online_mask in this case would have only 8 bits set, in a sparse way.
In general case, when SMT is off the cpu_online_mask has only C bits set:
0, 1*N, 2*N, ..., C*(N-1) where
C == # of cores;
N == # of logical CPUs per core.
In our example, only bits 0, 8, 16, 24, 32, 40, 48, 56 would be set.
This patch changes the way q_vector's affinity_mask is created: it iterates
on v_idx, but consumes the CPU index from the cpu_online_mask instead of
just using the v_idx incremental value.
No functional changes were introduced.
Signed-off-by: Guilherme G Piccoli <gpiccoli@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch sets VSI broadcast promiscuous mode during VSI add sequence
and prevents adding MAC filter if specified MAC address is broadcast.
Change-ID: Ia62251fca095bc449d0497fc44bec3a5a0136773
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When LLDP/DCBX change happens the i40e driver code flow tried to
notify the client(s) for each of the PF VSIs. This resulted into
kernel panic on the first VSI that didn't have any netdev
associated to it.
The DCB change notification to the client(s) should be done only
once for the PF/LAN VSI where the client(s) instances have been
added to. Also, move the notification call after the PF driver has
made changes related to the updated DCB configuration.
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Tested-by: Ronald J Bynoe <ronald.j.bynoe@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On systems with 128 CPUs, turning off TSO results in errors,
i40e 0000:03:00.0: failed to get tracking for 1 vectors for VSI 400, err=-12
i40e 0000:03:00.0: Couldn't create FDir VSI
i40e 0000:03:00.0: i40e_ptp_init: PTP not supported on eth0
i40e 0000:03:00.0: couldn't add VEB, err I40E_ERR_ADMIN_QUEUE_ERROR aq_err I40E_AQ_RC_ENOENT
i40e 0000:03:00.0: rebuild of switch failed: -1, will try to set up simple PF connection
i40e 0000:03:00.0 eth0: adding 00:10:e0:8a:24:b6 vid=0
Enabling FD_SB without checking availability of MSI-X vector is the
root cause. This change adds necessary check.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the macaddr add and delete happens asynchronously, error
messages don't easily get associated to the actual request. Here
we add a bit of information to the error messages to help
determine the source of the error.
Change-ID: Id2d6df5287141c3579677d72d8bd21122823d79f
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the need for a reset when the device enters limited promiscuous
mode. This was causing heartburn for people who were using VFs and
bridging, since this would require all of the VFs to undergo a reset
each time the PF changed its promiscuity.
Change-ID: I0a83495c5e4d68112bbc7a7a076d20fa8dd3b61c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Limiting qcount to pf->num_lan_msix, effectively limits the RSS queues
to only use the number of CPUs, and ignore all other queues. We don't
want to do this. If the user has changed the RSS settings to use more
queues then CPUS, we want to trust they know what they are doing and
let them. More importantly, if we tell them that is what we did, we want
to actually do it and allow traffic into all of the queues we have
allocated. This does not change the default setting to initially
allocate only the number of CPUS of queue pairs.
Change-ID: Ie941a96e806e4bcd016addb4e17affb46770ada5
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_suspend() function was failing to save PCI state
and this would result in a kernel stack trace from a WARN_ONCE in the
pci_legacy_suspend() function.
Add a call to pci_save_state() to fix that problem.
Change-ID: I4736e62bb660966bd208cc8af617a14cb07fc4bd
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_suspend() function calls another function that preps the device
for the power save and resume by freeing all the Tx/Rx resources and
interrupts but that function does not free the "other" causes interrupt
vector and IRQ. It also fails to call synchronize_irq() before freeing
the IRQ vectors. This sometimes may result in some AER errors on those
systems with that PCIe error reporting feature enabled.
Call synchronize_irq() before freeing IRQ vectors and explicitly free
the other causes interrupt resources and shut down that MSIX interrupt.
Change-ID: Ib88e4536756518a352446da0232189716618ad81
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were failing to set the client interface down when we put the VSI
down. Add this call so that the client doesn't get an open called with
no close.
Also remove an un-needed delay. The VF should not be affected at all by
i40e_down.
Change-ID: I1135dffef534bf84e6fed57cf51bcf590e6cfaf7
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function uses the i40e_hw struct all over the place, so why doesn't
it keep a pointer to the struct? Add this pointer as a local variable
and use it consistently throughout the function.
Change-ID: I10eb688fe40909433fcb8ac7ac891cef67445d72
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we do have pci_request_mem_regions() and pci_release_mem_regions()
at hand, use it in the Intel ethernet drivers.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: David S. Miller <davem@davemloft.net>
This patch goes through and combines the notifiers for VXLAN and GENEVE
into a single function for each action. So there is now one combined
function for getting ports, one for adding the ports, and one for deleting
the ports.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for offloading IPXIP6 type packets that represent
either IPv4 or IPv6 encapsulated inside of an IPv6 outer IP header. In
addition with this change we should also be able to support FOU
encapsulated traffic with outer IPv6 headers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines two new GSO definitions SKB_GSO_IPXIP4 and
SKB_GSO_IPXIP6 along with corresponding NETIF_F_GSO_IPXIP4 and
NETIF_F_GSO_IPXIP6. These are used to described IP in IP
tunnel and what the outer protocol is. The inner protocol
can be deduced from other GSO types (e.g. SKB_GSO_TCPV4 and
SKB_GSO_TCPV6). The GSO types of SKB_GSO_IPIP and SKB_GSO_SIT
are removed (these are both instances of SKB_GSO_IPXIP4).
SKB_GSO_IPXIP6 will be used when support for GSO with IP
encapsulation over IPv6 is added.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the SR-IOV VSIs, when the queue filtering section is valid,
the RSS LUT needs to be set to use the VSI specific lookup table
(otherwise it will use the PF RSS LUT table).
Change-ID: Ia9377cc818078238a75c3bdeade1b593a91b3480
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds priv-flag knob to configure global true promisc
support. With this patch the user can decide the flavor of
promiscuous that the VFs will see when promiscuous mode is enabled
on the interface. Since this a global setting for the whole device,
the priv-flag is exposed only on the first PF of the device.
The default is true promisc support is off, which means the promisc
mode for the VF will be limited/defport mode.
For the PF, we still will be in limited promisc unless in MFP mode
irrespective of the flavor picked through this knob.
Usage:
On PF0
ethtool --show-priv-flags p261p1
Private flags for p261p1:
MFP : off
LinkPolling : off
flow-director-atr : on
veb-stats : off
hw-atr-eviction : off
vf-true-promisc-support: off
to enable setting true promisc
ethtool --set-priv-flags p261p1 vf-true-promisc-support on
At this point if the VF is set to trust and promisc is enabled
on the VF through
ip link set ... promisc on
The VF/VFs will be able to see ALL ingress traffic
Change-Id: I8fac4b6eb1af9ca77b5376b79c50bdce5055bd94
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware supports a 16 byte descriptor for receive, but the
driver was never using it in production. There was no performance
benefit to the real driver of 16 byte descriptors, so drop a whole
lot of complexity while getting rid of the code.
Also since the previous patch made us use no-split mode all the
time, drop any support in the driver for any other value in dtype
and assume it is always zero (aka no-split).
Hooray for code removal!
Change-ID: I2257e902e4dad84a07b94db6d2e6f4ce69b27bc0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is part 1 of the Rx refactor series, just including
changes to i40e.
This refactor aligns the receive routine with the one in
ixgbe which was highly optimized. This reduces the code
we have to maintain and allows for (hopefully) more readable
and maintainable RX hot path.
In order to do this:
- consolidate the receive path into a single function that doesn't
use packet split but *does* use pages for Rx buffers.
- remove the old _1buf routine
- consolidate several routines into helper functions
- remove ethtool control over packet split
Change-ID: I5ca100721de65992aa0114f8b4bac844b84758e0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As part of preparation for the rx-refactor, remove the
packet split receive routine and ancillary code.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
previous patches removed all direct accesses to dev->trans_start,
so change the netif_trans_update helper to update trans_start of
netdev queue 0 instead and then remove trans_start from struct net_device.
AFAICS a lot of the netif_trans_update() invocations are now useless
because they occur in ndo_start_xmit and driver doesn't set LLTX
(i.e. stack already took care of the update).
As I can't test any of them it seems better to just leave them alone.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes it so that i40e and i40evf can use GSO_PARTIAL to support
segmentation for frames with checksums enabled in outer headers. As a
result we can now send data over these types of tunnels at over 20Gb/s
versus the 12Gb/s that was previously possible on my system.
The advantage with the i40e parts is that this offload is mostly
transparent as the hardware still deals with the inner and/or outer IPv4
headers so the IP ID is still incrementing for both when this offload is
performed.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a device ID for X722.
Change-Id: I574f2345ab341de98a6a1c212d0603af853e48b0
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_release_rx_desc was in two files, but was only used
and needed in txrx.c. Get rid of the extra copy.
Change-Id: I86e18239aa03531fc198b6c052847475084a9200
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With this change a non trusted VF can never fall to promiscuous
mode when there is no room for a MAC/VLAN filter.
Change-Id: I8a155aa25c0bcdc6093414920c9ade4ee0bd20e8
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for configuring RSS on behalf of the VFs. This removes the
burden of dealing with different hardware interfaces from the VF
drivers, allowing for better future compatibility.
Change-ID: Icea75d3f37241ee8e447be5779e5abb53ddf04c0
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Looking over the documentation it turns out enabling IPIP and SIT offloads
for i40e is pretty straightforward. As such I decided to enable them with
this patch. In my testing I am seeing an improvement of 8 to 10 Gb/s
for IPIP and SIT tunnels with this offload enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The feature flags list for i40e and i40evf is beginning to become pretty
massive. I plan to add another 4 or so features to these drivers and
duplicating the flags for each and every flags list is becoming a bit
repetitive.
The primary change here is that we now build our features list around
hw_encap_features. After that we assign that to vlan_features,
hw_features, and finally map that onto features. In addition we end up
throwing features onto hw_encap_features that end up having no effect such
as the Rx offloads and SCTP_CRC. However that should have no impact and
makes things a bit easier for us as hw_encap_features is one of the less
updated features maps available.
For i40evf I went through and sanity checked a few features as well.
Specifically RXCSUM was being set as a read-only feature which didn't make
much sense. I have updated things so we can clear the NETIF_F_RXCSUM flag
since that is really a software feature and not a hardware one anyway so
disabling it is just a matter of ignoring the result from the hardware.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds hook to support changing a VF from not-trusted
to trusted and vice-versa. Fixed the wrappers and function prototype.
Changed the dmesg to reflex the current state better. This patch also
disables turning on/off trusted VF in MFP mode.
Change-ID: Ibcd910935c01f0be1f3fdd6d427230291ee92ebe
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't set our internal debug_mask at startup unless we get specific signal
to from the debug module parameter.
This should take care of the issue with all the device capabilities getting
printed even when we hadn't asked for the debug info.
Change-ID: I7fbc6bd8b11ed9b0631ec018ff36015a04100b6c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the Media Not Available flag to the link event mask. It seems
that event comes first if you have a DA cable pulled out, but there's no
follow-up event for Link Down; if you're not looking for MEDIA_NA you will
get no event, even though there's now no Link.
Change-ID: cb3340a2849805bb881f64f6f2ae810eef46eba7
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Periodic link polling was added when the link events were found not to be
trustworthy. This was the case early on, but was likely because the link
event mask was being used incorrectly. As this has been fixed in recent
code, we can disable the link polling to lessen the AQ traffic.
Change-ID: Id890b5ee3c2d04381fc76ffa434777644f5d8eb0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new device ID is 0x37D3 and it should follow the same flows and
branding string as for 0x37D0.
Change-ID: Ia5ad4a1910268c4666a3fd46a7afffbec55b4fc2
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables the Capability for XL710/X710 devices with FW API
version higher than 1.4 to do geneve Rx offload.
Change-ID: I9a8f87772c48d7d67dc85e3701d2e0b845034c0b
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There was an error introduced with commit 3fced53507 ("i40e: X722 is
on the IOSF bus and does not report the PCI bus info"), where code was
added but the enabling flag is never set.
CC: Anjali Singhai Jain <anjali.singhai@intel.com>
CC: Stefan Assman <sassman@redhat.com>
Fixes: 3fced53507 ("i40e: X722 is on the IOSF bus ...")
Reported-by: Steve Best <sbest@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's no real error in an unknown event from the Firmware, we're just
posting a useful FYI notice, so this patch simply removes the "Error" word.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Notify VFs in the reset interrupt handler, instead of the actual
reset initiation code. This allows the VFs to get properly notified for
all resets, including resets initiated by different PFs on the same
physical device.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some error scenarios, we may find ourselves trying to remove a
non-existent timer or worktask. This causes the kernel some bit
of consternation, so don't do it.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When dropping into debug mode in a failed probe, make sure that
the AdminQ is left alive for possible hand debug of driver and
firmware states.
Move the mutex_init calls earlier in probe so that if init fails,
the admin queue interface is still available for debugging purposes.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When cleaning up the interrupt handling, clean up the IRQs only if
we actually got them set up. There are a couple of error recovery
paths that were violating this and causing the kernel a bit of
indigestion.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Reviewed-by: Williams, Mitch A <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
- A few minor core fixups needed for the next patch series
- The IB SRIOV series. This has bounced around for several versions.
Of note is the fact that the first patch in this series effects
the net core. It was directed to netdev and DaveM for each iteration
of the series (three versions total). Dave did not object, but did
not respond either. I've taken this as permission to move forward
with the series.
- The new Intel X722 iWARP driver
- A huge set of updates to the Intel hfi1 driver. Of particular interest
here is that we have left the driver in staging since it still has an
API that people object to. Intel is working on a fix, but getting
these patches in now helps keep me sane as the upstream and Intel's
trees were over 300 patches apart.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=t2Ko
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull more rdma updates from Doug Ledford:
"Round two of 4.6 merge window patches.
This is a monster pull request. I held off on the hfi1 driver updates
(the hfi1 driver is intimately tied to the qib driver and the new
rdmavt software library that was created to help both of them) in my
first pull request. The hfi1/qib/rdmavt update is probably 90% of
this pull request. The hfi1 driver is being left in staging so that
it can be fixed up in regards to the API that Al and yourself didn't
like. Intel has agreed to do the work, but in the meantime, this
clears out 300+ patches in the backlog queue and brings my tree and
their tree closer to sync.
This also includes about 10 patches to the core and a few to mlx5 to
create an infrastructure for configuring SRIOV ports on IB devices.
That series includes one patch to the net core that we sent to netdev@
and Dave Miller with each of the three revisions to the series. We
didn't get any response to the patch, so we took that as implicit
approval.
Finally, this series includes Intel's new iWARP driver for their x722
cards. It's not nearly the beast as the hfi1 driver. It also has a
linux-next merge issue, but that has been resolved and it now passes
just fine.
Summary:
- A few minor core fixups needed for the next patch series
- The IB SRIOV series. This has bounced around for several versions.
Of note is the fact that the first patch in this series effects the
net core. It was directed to netdev and DaveM for each iteration
of the series (three versions total). Dave did not object, but did
not respond either. I've taken this as permission to move forward
with the series.
- The new Intel X722 iWARP driver
- A huge set of updates to the Intel hfi1 driver. Of particular
interest here is that we have left the driver in staging since it
still has an API that people object to. Intel is working on a fix,
but getting these patches in now helps keep me sane as the upstream
and Intel's trees were over 300 patches apart"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (362 commits)
IB/ipoib: Allow mcast packets from other VFs
IB/mlx5: Implement callbacks for manipulating VFs
net/mlx5_core: Implement modify HCA vport command
net/mlx5_core: Add VF param when querying vport counter
IB/ipoib: Add ndo operations for configuring VFs
IB/core: Add interfaces to control VF attributes
IB/core: Support accessing SA in virtualized environment
IB/core: Add subnet prefix to port info
IB/mlx5: Fix decision on using MAD_IFC
net/core: Add support for configuring VF GUIDs
IB/{core, ulp} Support above 32 possible device capability flags
IB/core: Replace setting the zero values in ib_uverbs_ex_query_device
net/mlx5_core: Introduce offload arithmetic hardware capabilities
net/mlx5_core: Refactor device capability function
net/mlx5_core: Fix caching ATOMIC endian mode capability
ib_srpt: fix a WARN_ON() message
i40iw: Replace the obsolete crypto hash interface with shash
IB/hfi1: Add SDMA cache eviction algorithm
IB/hfi1: Switch to using the pin query function
IB/hfi1: Specify mm when releasing pages
...
This patch adds a Client interface for i40iw driver
support. Also expands the Virtchannel to support messages
from i40evf driver on behalf of i40iwvf driver.
This client API is used by the i40iw and i40iwvf driver
to access the core driver resources brokered by the i40e driver.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
For i40e driver, each vector has its own ITR register. However, there
are no concept of queue-specific settings in the driver proper. Only
global variable is used to store ITR values. That will cause problems
especially when resetting the vector. The specific ITR values could be
lost.
This patch move rx_itr_setting and tx_itr_setting to i40e_ring to store
specific ITR register for each queue.
i40e_get_coalesce and i40e_set_coalesce are also modified accordingly to
support queue-specific settings. To make it compatible with old ethtool,
if user doesn't specify the queue number, i40e_get_coalesce will return
queue 0's value. While i40e_set_coalesce will apply value to all queues.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to suspend scheduling or any pending service task during driver
unload process, so that new task will not be scheduled. This patch sets
the suspend flag bit during reload which avoids service task execution.
Change-ID: I017c57b5d6656564556e3c5387da671369a572ac
Signed-off-by: Pandi Kumar Maharajan <pandi.maharajan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the new AdminQ functions for safely accessing the Rx control
registers that may be affected by heavy small packet traffic.
We can't use AdminQ calls in i40e_clear_hw() because the HW is being
initialized and the AdminQ is not alive. We recently added an AQ
related replacement for reading PFLAN_QALLOC, and this patch puts
back the original register read.
Change-ID: Ib027168c954a5733299aa3a4ce5f8218c6bb5636
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Return from i40e_vsi_reinit_setup() if vsi param is NULL.
This makes this code consistent with all the other code that
checks for NULL before using one of the VSI pointers accessed
with an indexed variable. (Indexed VSI pointers are
intentionally set to NULL in i40e_vsi_clear() and
i40e_remove().
Change-ID: I3bc8b909c70fd2439334eeae994d151f61480985
Signed-off-by: John Underwood <johnx.underwood@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fixes an issue where a previously removed message
has returned. Changing the message type to dev_dbg
leaves the info, if desired, but takes it out of normal
everyday usage. Also changed call to only provide port
data when its valid and not when its not (delete case).
Change-ID: Ief6f33b915f6364c24fa8e5789c2fc3168b5e2ed
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Just like Tx queues don't wait for Rx queues to be disabled before
DCB has been reconfigured.
Check the queues are disabled only after the DCB configuration has
been applied to the VSI(s) managed by the PF driver.
In case of any timeout issue a PF reset to recover.
Change-ID: Ic51e94c25baf9a5480cee983f35d15575a88642c
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where the ethtool identify adapter
functionality did not work for some copper PHY's. Without this
patch, the blink led functionality fails on some parts. This
patch adds PHY write code to blink led's on parts where this
functionality is contained in the PHY rather than the MAC.
Change-ID: Iee7b3453f61d5ffd0b3d03f720ee4f17f919fcc2
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent changes should have enabled support for IPv6 based tunnels and
support for TSO with outer UDP checksums. As such we can update the
feature flags to reflect that.
In addition we can clean-up the flags that aren't needed such as SCTP and
RXCSUM since having the bits there doesn't add any value.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All of the documentation in the datasheets for the XL710 do not call out
any reason to exclude support for IPv6 based tunnels. As such I am
dropping the code that was excluding these tunnel types from having their
port numbers recognized. This way we can take advantage of things such as
checksum offload for inner headers over IPv6 based VXLAN or GENEVE
tunnels.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e and i40evf drivers contained code for inserting an outer checksum
on UDP tunnels. The issue however is that the upper levels of the stack
never requested such an offload and it results in possible errors.
In addition the same logic was being applied to the Rx side where it was
attempting to validate the outer checksum, but the logic there was
incorrect in that it was testing for the resultant sum to be equal to the
header checksum instead of being equal to 0.
Since this code is so massively flawed, and doing things that we didn't ask
for it to do I am just dropping it, and will bring it back later to use as
an offload for SKB_GSO_UDP_TUNNEL_CSUM which can make use of such a
feature.
As far as the Rx feature I am dropping it completely since it would need to
be massively expanded and applied to IPv4 and IPv6 checksums for all parts,
not just the one that supports Tx checksum offload for the outer.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure we return EBUSY while finishing up a reset, and add a few bits
for better debug messages.
Change-ID: I23f6c28a8d96d7aa171abcc265737cec7826c292
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The queues should never be enabled/disabled in the interrupt handler,
ICR0 interrupt enable should be the only thing that needs to be
dynamically changed in the handler.
This patch fixes that. Without this patch X722 platforms were
seeing weird ping timings when in Legacy mode since it takes
a whole lot of time for the HW/FW to re-enable queues.
Change-ID: If065afc45d81c5a19d4a94a00cd5b8f61cefc40c
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixed mapping of SEID is removed from specification. Hence
this patch removes code which was using hard coded base VEB SEID.
Changed FCoE code to use "hw->pf_id" to obtain correct "idx"
and verified.
Removed defines for BASE VSI/VEB SEID and BASE_PF_SEID since it
is not used anymore.
Change-ID: Id507cf4b1fae1c0145e3f08ae9ea5846ea5840de
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch falls back to enabling unicast, multicast and
broadcast promiscuous mode when the driver must disable it's use
of "default port" aka defport mode (which is normally used to
provide a promiscuous mode), due to internal incompatibility
with Multiple Function per Port (aka MFP).
The situation that requires this patch is when Physical
Function 0 is the device being used, and it can support SR-IOV
when MFP is enabled, via the driver creating a VEB on an MFP
enabled adapter.
Change-ID: Ie90b00d0d58782a5dfcf2c3c9725a2eb90bd63d8
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a workaround for cases where we might have
interrupts that got lost but WB happened.
If that happens without this patch we will see a tx_timeout.
To work around it, this patch goes ahead and reschedules NAPI
in that situation, if NAPI is not already scheduled.
We also add a counter in ethtool to keep track of when
we detect a case of tx_lost_interrupt.
Note: napi_reschedule() can be safely called from process/service_task
context and is done in other drivers as well without an issue.
Change-ID: I00f98f1ce3774524d9421227652bef20fcbd0d20
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes use of a pointer called hw consistent
in the i40e_remove function.
Change-ID: Idacc7ff0a09a68289c57457a78618bf5497de077
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump version to i40e-1.4.13 and i40evf-1.4.9
Change-ID: I9db37f9d4899141c3e5455dfb456d45465b8c035
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While re-enabling interrupts the driver would clear all pending
causes. This meant that if an interrupt was generated while the driver
was cleaning or polling with interrupts disabled, then that interrupt
was lost. This could cause a queue to become dead, especially for
receive. Refactored the enable_icr0 function in order to allow
it to be decided by the caller whether the CLEARPBA (clear pending
events) bit will be set while re-enabling the interrupt.
Also update copyright year in file headers.
Change-ID: Ic1db100a05e13c98919057696db147a258ca365a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new parameters for add_veb allow us to enable and disable VEB stats,
so let's use them.
Update copyright year.
Change-ID: Ie6e68c68e2d1d459e42168eda661051b56bf0a65
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the latest firmware, statistics gathering can now be enabled and
disabled in the HW switch, so we need to add a parameter to allow the
driver to set it as desired. At the same time, the L2 cloud filtering
parameter has been removed as it was never used.
Older drivers working with the newer firmware and newer drivers working
with older firmware will not run into problems with these bits as the
defaults are reasonable and there is no overlap in the bit definitions.
Also, newer drivers will be forced to update because of the change in
function call parameters, a reminder that the functionality exists.
Also update copyright year.
Change-ID: I9acb9160b892ca3146f2f11a88fdcd86be3cadcc
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make the DCB firmware version related checks specific to
X710 and XL710 only. These checks are not required for
X722 family of devices.
Introduced an inline routine to help determine if the
MAC type is X710/XL710 or not.
Moved the firmware version related checks in i40e_sw_init()
and defined flags for different cases
Fix the version check to allow using "Set LLDP MIB" AQ
for beyond FVL4 FW releases.
Change-ID: Ib78288343de983aa0354fc28aa36e99b073662c0
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The sync_vsi_filters function is moved up in the service_task because
it may need to request a reset, and we don't want to wait another round
of service task time.
NOTE: Filters will be replayed by sync_vsi_filters including broadcast
and promiscuous settings.
Also, added some error handling in this space in case any of these
fail the driver will retry correctly.
Also update copyright year.
Change-ID: I23f3d552100baecea69466339f738f27614efd47
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This commit converts commit b499ffb0a2 ("i40e: Look up MAC address in
Open Firmware or IDPROM") to use eth_platform_get_mac_address()
added by commit c7f5d10549 ("net: Add eth_platform_get_mac_address()
helper.")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X722 can support automatic rule eviction for automatically added
flow director rules. Feature is (should be) disabled by default.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes sure we check the GENEVE offload capable flag before
we attempt offload.
It also enables the Capability for XL710/X710 devices with FW API
version higher than 1.4
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PHY interrupt mask bits mask out the events we don't want,
so we need to negate the bitmask of events we want.
Change-ID: I273244da5a8d285b6abc84fd68a90f1e6fa0393e
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was being called by VLAN, bonding, teaming operations
that expected to be able to hold locks like rcu_read_lock().
This causes the driver to be held to the requirement to not sleep,
and was found by the kernel debug options for checking sleep
inside critical section, and the locking validator.
Change-ID: Ibc68c835f5ffa8ffe0638ffe910a66fc5649a7f7
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Nelson, Shannon <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The sync_vsi_filter function was allocating memory in such
a way that it could sleep (GFP_KERNEL) which was causing a problem
when called by the team driver under rcu_read_lock(), which cannot
be held while sleeping. Found with lockdep.
Change-ID: I4e59053cb5eedcf3d0ca151715be3dc42a94bdd5
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Missing space in comment, fixed.
Change-ID: I8cdf3ce5994b4a97dcc3eeb33422533918546667
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The probe routine already had a u32 val declared, no need
to do it again. Found by W=2 compile.
Change-ID: Id7b65f6d0ef6bb71067d0557f5be0202b6d8741e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-02-16
This series contains updates to i40e/i40evf only.
Shannon adds flags to MAC allocation requests to signify that the MAC VLAN
filters should come from the shared resource pool. Added a new "set switch
config" admin queue command and the new Cisco VXLAN-GPE cloud tunnel type
for the admin queue commands. Added more detail to the NVM update debug
message in order to see the full ethtool request data. Also added a few
more bits of netdev data into the debugfs output for dump VSI.
Pandi fixes the width of two datatypes which were being declared a different
size from what they are assigned.
Anjali fixes an issue where we were not doing write-back on interrupt
throttle for legacy case in x722.
Mitch adds a counter for ARQ overflows since sometimes an ever-growing
number indicates that something bad is happening. Also added 20G speed for
Tx bandwidth calculations.
Jesse refactors the DCB function based on a community suggestion to change
the multi-level if statement into a switch statement. Cleans up VF device
IDs in the PF, since it does not need to know them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates setup_tc so we can pass additional parameters into
the ndo op in a generic way. To do this we provide structured union
and type flag.
This lets each classifier and qdisc provide its own set of attributes
without having to add new ndo ops or grow the signature of the
callback.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ndo_setup_tc() op was added to support drivers offloading tx
qdiscs however only support for mqprio was ever added. So we
only ever added support for passing the number of traffic classes
to the driver.
This patch generalizes the ndo_setup_tc op so that a handle can
be provided to indicate if the offload is for ingress or egress
or potentially even child qdiscs.
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Probe routine already has too many locals, just convert one
used for kzalloc into a kcalloc, eliminating the local.
Change-ID: I349049872b71f858cbeb91ad7836e6767fc7b7d1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Anjali Singhai <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sometimes, ARQ overflows are a big deal and tell us that the
firmware/hardware/driver/something is having problems. But normally
they're no big deal. To assist in assessing this, add a counter to
our Ethtool stats. A handful of ARQ overflows during VF init is no
problem. A large, ever-growing number indicates that Something Bad is
happening.
Change-ID: Ie5348bfbc8a54a890559cb00279c28d976a55096
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add some missing reporting/advertisement of 100Mb capability
for adapters that support it.
Change-ID: I8b8523fbdc99517bec29d90c71b3744db11542ac
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As done per ixgbe, use a private workqueue to avoid blocking the
system workqueue. This avoids some strange side effects when
some other entity is depending on the system work queue.
Change-ID: Ic8ba08f5b03696cf638b21afd25fbae7738d55ee
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds another way to access the RSS keys and lut using the AQ
for X722 devices.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the KX and QSFP device IDs for X722.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The restart-autoneg work around does not apply to X722.
Added a flag to set it only for the right MAC and right FW version
where the work around should be applied.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Change-ID: I942c3ff40cccd1e56f424b1da776b020fe3c9d2a
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add MAC filter element to the end of the list in the given order,
just to be tidy, and just in case there are ever any ordering issues in
the future.
Change-ID: Idc15276147593ea9393ac72c861f9c7905a791b4
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes following build warnings :
drivers/net/ethernet/intel/i40e/i40e_main.c:7057:13: warning:
'i40e_sync_udp_filters_subtask' defined but not used [-Wunused-function]
drivers/net/ethernet/intel/i40e/i40e_main.c:8524:13: warning:
'i40e_add_vxlan_port' defined but not used [-Wunused-function]
drivers/net/ethernet/intel/i40e/i40e_main.c:8569:13: warning:
'i40e_del_vxlan_port' defined but not used [-Wunused-function]
drivers/net/ethernet/intel/i40e/i40e_main.c:8604:13: warning:
'i40e_add_geneve_port' defined but not used [-Wunused-function]
drivers/net/ethernet/intel/i40e/i40e_main.c:8651:13: warning:
'i40e_del_geneve_port' defined but not used [-Wunused-function]
Fixes: 6a89902405 ("i40e: geneve tunnel offload support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Somehow an ID that has never been productized is in the
code. There are no plans to use it, so just get
rid of it.
Change-ID: I59117d48ea9ee0360b0fe33833ac8092f8a24b4c
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the i40e equivalent of commit c762dff24c ("ixgbe: Look up MAC
address in Open Firmware or IDPROM").
As with that fix, attempt to look up the MAC address in Open Firmware
on systems that support it, and use IDPROM on SPARC if no OF address
is found.
In the case of the i40e there is an assumption that the default mac
address has already been set up as the primary mac filter on probe,
so if this filter is obtained from the Open Firmware or IDPROM, an
explicit write is needed via i40e_aq_mac_address_write() and
i40e_aq_add_macvlan() invocation.
The I40E_FLAG_PF_MAC flag in the platform-private i40e_pf structure
tracks whether a platform-specific mac address was found, in which
case calls to i40e_aq_mac_address_write() and i40e_aq_add_macvlan()
will be triggered.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a call to geneve_get_rx_port in i40e so that when it
comes up it can learn about the existing geneve tunnels.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds driver hooks to implement ndo_ops to add/del
udp port in the HW to identify GENEVE tunnels.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP checksum is really a CRC and is very different from the
standards 1's complement checksum that serves as the checksum
for IP protocols. This offload interface is also very different.
Rename NETIF_F_SCTP_CSUM to NETIF_F_SCTP_CRC to highlight these
differences. The term CSUM should be reserved in the stack to refer
to the standard 1's complement IP checksum.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean the whole mac filter list when resetting after an intermediate
add or delete push to the firmware. The code had evolved from using
a list from the stack to a heap allocation, but the memset() didn't
follow the change correctly. This now cleans the whole list rather
that just part of the first element.
Change-ID: I4cd03d5a103b7407dd8556a3a231e800f2d6f2d5
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These messages seem big and scary, but they're really not. The driver
can fully recover from any of these. The overflow error in particular
can happen when enabling a bunch of VFs and the VF driver is not
blacklisted.
Since these messages are really for debugging purposes, reclassify
them as such.
Change-ID: I628d0f5e135e7063450ba05393a50b7af23aa6d7
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a part of implementation which contains data structures and
opcode for new AQ command. There's a new ARQ message that gets sent
near the end of the NVM update process that the driver should recognize
and ignore, rather than printing an Unknown Event error.
Change-ID: I04830a5bcae14823e16b9424cc4165e169336c1f
Signed-off-by: Michal Kosiarz <michal.kosiarz@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The virtual channel interface was using incorrect semantics to remove
MAC addresses, which would leave incorrect filters active when using
VLANs. To correct this, add a new function that unconditionally removes
MAC addresses from all VLANs, and call this function when the VF
requests a MAC filter removal.
Change-ID: I69826908ae4f6c847f5bf9b32f11faa760189c74
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
BIT_ULL was used on a u32 or less where it can simply be BIT. This
fixes some trivial static analyzer warnings. Chomp, chomp.
Tested with objdump of binary before and after, no changes to code.
Change-ID: I6245e9abd447192dbde1669c747aeb2878126c7d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This reverts commit 8fe269991a.
The case where VXLAN is a module and i40e driver is inbuilt
will not be handled properly with this change since i40e
will have an undefined symbol vxlan_get_rx_port in it.
v2: Add a signed-off-by.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver were to happen to have a mutex held while
the i40e_init_adminq call was called, the init_adminq might
inadvertently call mutex_init on a lock that was held
which is a violation of the calling semantics.
Fix this by avoiding adminq.c code allocating/freeing this memory, and
then do the same work only once in probe/remove.
Testing Hints (Required if no HSD): for VF, load i40evf in bare metal
and echo 32 > sriov_numvfs; echo 0 > sriov_numvfs in a loop. Yes this
is a horrible thing to do.
Change-ID: Ida263c51b34e195252179e7e5e400d73a99be7a2
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2015-12-03
This series contains updates to i40e and i40evf only.
Mitch updates the i40evf driver by increasing the maximum number of queues,
since future devices will allow for more queue pairs. Cleans up a
duplicate printing of the driver info string done in init, since it is
already done in probe. Cleaned up the several allocations which did
not need to be at atomic level, where GFP_KERNEL would work just fine.
Then makes i40e_sync_vsi_filters() a more mature function, make having
a common exit point so it will properly release the busy lock on the VSI
and propagate errors to the callers. Then does some whitespace
housekeeping in i40evf.
Kiran moves and updates the detection/recovery of transmit queue hang code
to service_task from tx_timeout function. Also fixed memory leak when
users program flow-director filter using ethtool (sideband filter
programming), the cause being the check of 'tx_buffer->skb' was preventing
'raw_buf' from being freed as part of the cleanup.
Jesse enabled the ability to turn off/on packet split using ethtool priv
flags. Then does some housekeeping for both the i40e and i40evf drivers
which includes: remove unused/useless code, correct whitespace, remove
duplicate #include, fix incorrect comment, etc...
Neerav cleans up functions to gather Flow Control Rx XOFF stats, since
the recent change in the driver logic for checking transmit hang has been
moved, so these functions do not do anything meaningful any longer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7fd89545f3 ("i40e: remove BUG_ON from feature string building")
added defective output when I40E_FLAG_VEB_MODE_ENABLED was set in
function i40e_print_features.
Fix it.
Miscellanea:
- Remove unnecessary string variable
- Add space before not after fixed strings
- Use kmalloc not kzalloc
- Don't initialize i to 0, use result of first snprintf
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The separate functions to gather Flow control Rx XOFF stats was to
determine if the Tx for a queue was paused due to Link Flow Control(LFC)
or Priority Flow Control(PFC).
But, with recent change in the i40e driver the logic for checking th Tx
hang has been removed and these functions don't do anything meaningful.
Hence, there is no need to keep these separate functions to gather Rx
XOFF stats for LFC or PFC.
This patch removes these functions and moves the stat collection for
XOFF Rx to the i40e_update_pf_stats() that collects all the PF stats.
Change-ID: Iec1452dac3a6766f0d968e754cb407530d7c60cd
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of having our own custom symbol, we can just rely
on whether or not the kernel has the feature enabled.
In this case use IS_ENABLED(CONFIG_VXLAN) in order to handle
built-in or module in the current BKM way.
Change-ID: I5890fbb518ff8ed6bb07c3362fb0a8a829f9b241
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_sync_vsi_filters() is the surly teenager of this driver. It says
it's going to report errors, but it doesn't actually do that most of the
time. And when it does, it leaves a mess.
Change this function to have a common exit point so it will properly
release the busy lock on the VSI. Propagate errors to the callers.
Finally, adjust a few callers to check for and deal with errors from
this function.
Change-ID: Ic6af4956491e72402ebb3c538a3c31a0ad7f8667
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains following changes:
- detection and recovery logic (issue SW interrupt) has been moved to
service_task from timeout function.
- added some more debug info from tx_timeout.
Logic to detect and recover TX queue hung is now two step process:
- service_task detects TX queue hung and sets a bit(hung_detected) if
it was not set.
- if bit was set (means this is back-back hung condition detected),
issue SW interrupt and clear the bit.
- napi_poll clears the bit unconditionally since it cleans TX/RX queues.
Change-ID: Ieed03a48927c845a988b3ff375090bf37caeb903
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the final edition of the patches to remove sleeps from
the driver's entry points, the grab_rtnl argument is no
longer needed, so partially revert the commit that added it.
Change-ID: Ib9778476242586cc9e58b670f5f48d415cb59003
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was being called by VLAN, bonding, teaming operations
that expected to be able to hold locks like rcu_read_lock().
This causes the driver to be held to the requirement to not sleep,
and was found by the kernel debug options for checking sleep
inside critical section, and the locking validator.
Change-ID: Ibc68c835f5ffa8ffe0638ffe910a66fc5649a7f7
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the confusing kernel message of enabled RSS size,
by reporting it together with the hardware maximum RSS size.
Change-ID: I64864dbfbc13beccc180a7871680def1f3d5a339
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue where adminq init failures always provided
a message that NVM was newer than expected. This is not always the
case for init_adminq failures. Without this patch, if adminq init
fails for any reason, newer NVM message would be given. This
problem is fixed by adding a check for that specific error
condition and a different hopefully helpful message otherwise.
Change-ID: Iaeaebee4e398989eae40bb70f943ab66a3a521a5
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch renames rss_size to alloc_rss_size in i40e_pf, which is
clearer and avoids confusion. It also adds comments to the other
related structure members to help clarify usage.
Change-ID: Ia90090609d006ab589cb639975bb8a0af795d16f
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds new fields to i40e_vsi to store user configured
RSS config data and code to use it.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Change-ID: I73886469dca9e9f6b16d842182a87f3f4009f95d
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch renames the old pf-specific function in order to clarify
its scope. This patch also creates a more generic configure RSS
function with the old name.
This patch also creates a new more generic function to get RSS
configuration, using the appropriate method.
Change-ID: Ieddca2707b708ef19f1ebccdfd03a0a0cd63d3af
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adjust the RSS configure functions so that there is a generic way to
hook to ethtool hooks.
Change-ID: If446e34fcfaf1bc3320d9d319829a095b5976e67
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The watchdog only calls link_event not handle_link_event which means
that we need to save the old information in link_event.
Previously when polling we were comparing current data to the old data
saved the last time we actually received a link event. This means that
the polling would only fix link status changes in one direction
depending on what the last old data saved off was.
Change-ID: Ie590f30fdbcb133d0ddad4e07e3eb1aad58255b3
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When in NAPI with interrupts disabled, the HW needs to be forced to do a
write back on TX if the number of descriptors pending are less than a
cache line.
This stat helps keep track of how many times we get into this situation.
Change-ID: I76c1bcc7ebccd6bffcc5aa33bfe05f2fa1c9a984
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
HW/NVM sets a limit of no less than 256 bytes for MSS. Stack can send as
low as 76 bytes MSS. This patch lowers the HW limit to 64 bytes to avoid
MDDs from firing and causing a reset when the MSS is lower than 256.
Change-ID: I36b500a6bb227d283c3e321a7718e0672b11fab0
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's really no reason to kill the kernel thread just because of a
little info string. This reworks the code to use snprintf's limiting to
assure that the string is never too long, and WARN_ON to still put out
a warning that we might want to look at the feature list length.
Prompted by a recent Linus diatribe.
Change-ID: If52ba5ca1c2344d8bf454a31bbb805eb5d2c5802
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's no need to kill the thread and eventually the kernel in this
case. In fact, the remainder of the code won't hurt anything anyway,
so just complain that we're here and move along.
Prompted by a recent Linus diatribe.
Change-ID: Iec020d8bcfedffc1cd2553cc6905fd915bb3e670
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump up the version...
Change-ID: Ib8d501021671ba20250115ed54330e2c182255b7
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem of possibly getting inconsistent flow control
statuses after a PF reset. Requested_mode was being set with a default
value during probing, but the initial HW state could be different from
this mode.
Change-ID: I772bf07b78616e87086418d4bd87954b66fa17cd
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix i40e_is_vsi_uplink_mode_veb to check if bridge is actually
in VEB mode before allowing LB in the add VSI routine, instead of
unconditionally returning VEB bridge mode.
Change-ID: I162397b1bdd02367735fe9baaeb51465be2a3ce9
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a workaround to drop any flow control frames from being
transmitted from any VSI. FW can still send flow control frames if flow
control is enabled.
With this patch in place a malicious VF cannot send flow control or PFC
packets out on the wire.
Change-ID: I4303b24e98b93066d2767fec24dfe78be591c277
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was printing a message about not being able
to assign VMDq because of a lack of MSI-X vectors.
This was because a line was missing that initialized a variable,
simply a merge error.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-10-19
This series contains updates to i40e and i40evf only.
Kiran adds a spinlock around code accessing VSI MAC filter list to
ensure that we are synchronizing access to the filter list, otherwise
we can end up with multiple accesses at the same time which can cause
the VSI MAC filter list to get in an unstable or corrupted state.
Jesse fixes overlong BIT defines, where the RSS enabling call were
mistakenly missed. Also fixes a bug where the enable function was
enabling the interrupt twice while trying to update the two interrupt
throttle rate thresholds for Rx and Tx, while refactoring the IRQ
enable function to simplify reading the flow. Addressed the high
CPU utilization of some small streaming workloads that the driver should
reduce CPU in.
Anjali fixes two X722 issues with respect to EEPROM checksum verify and
reading NVM version info. Fixed where a mask value was accidentally
replaced with a bit mask causing Flow Director sideband to be broken.
Alex Duyck fixes areas of the drivers which run from hard interrupt
context or with interrupts already disabled in netpoll, so use
napi_schedule_irqoff() instead of napi_schedule().
Mitch fixes the VF drivers to not easily give up when it is not able
to communicate with the PF driver.
Carolyn fixes a problem where our tools MAC loopback test, after driver
unbind would fail because the hardware was configured for multiqueue and
unbind operation did not clear this configuration. Also fixed a issue
where the NVMUpdate tool gets bad data from the PHY when using the PHY
NVM feature because of contention on the MDIO interface from getting
PHY capability calls from the driver during regular operations.
Catherine fixed an issue where we were checking if autoneg was allowed
to change before checking if autoneg was changing, these checks need to
be in the reverse order.
Jean Sacren fixes up an function header comment to align the kernel-docs
with the actual code.
v2: Cleaned up the use of spin_is_locked() in patch 1 based on feedback
from David Miller, since it always evaluates to zero on uni-processor
builds
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
'err' would be overwritten immediately, so we should declare it only
rather than initialize it to zero.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The second argument name in the kernel-doc argument list for
i40e_features_check() was slightly off. Fix it for the kernel doc.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where our Tools MAC Loopback test, after
driver unbind would fail. This was because the hw was configured
for multiqueue and unbind operation did not clear this configuration.
The problem is fixed by resetting this configuration in i40e_remove.
Change-ID: I130c05138319182ed1476d3a0b5222d6a6320af9
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The adaptive ITR (interrupt throttle rate) algorithm was adjusting
the hardware's interrupt rate too frequently. This caused a lot
of variation in the interrupt rate for fairly constant workloads.
Change the code to have a counter and adjust only once every N
number of interrupts.
Change-ID: I0460f1f86571037484eca5aca36ac4d889cb8389
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_intr and i40e/i40evf_msix_clean_rings functions run from hard
interrupt context or with interrupts already disabled in netpoll.
They can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces a spinlock which is to be used for synchronizing
access to VSI's MAC filter list.
This patch also synchronizes execution of other codepaths which are
accessing VSI's MAC filter list with execution of
service_task:sync_vsi_filters.
In function i40e_add_vsi, copied out LAA MAC address instead of cloning
MAC filter entry because only MAC address is needed to remove MAC VLAN
filter from FW/HW.
Change-ID: I0e10ac7c715d44aa994239642aa4d57c998573a2
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The XL710 hardware has a different interrupt moderation design
that can support a limit of total interrupts per second per
vector, in addition to the "number of interrupts per second"
controls already established in the driver. This combination
of hardware features allows us to set very low default latency
settings but minimize the total CPU utilization by not
making too many interrupts, should the user desire.
The current driver implementation is still enabling the dynamic
moderation in the driver, and only using the rx/tx-usecs
limit in ethtool to limit the interrupt rate per second, by default.
The new code implemented in this patch
2) adds init/use of the new "Interrupt Limit" register
3) adds ethtool knob to control/report the limits above
Usage is ethtool -C ethx rx-usecs-high <value> Where <value> is number
of microseconds to create a rate of 1/N interrupts per second,
regardless of rx-usecs or tx-usecs values. Since there is a credit based
scheme in the hardware, the rx-usecs and tx-usecs can be configured for
very low latency for short bursts, but once the credit runs out the
refill rate on the credits is limited by rx-usecs-high.
Change-ID: I3a1075d3296123b0f4f50623c779b027af5b188d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cut down on the number of startup log entries by putting a couple behind
debug flags and combining a couple others into a single line.
Change-ID: I708089f086308f84d43f8b6f0e8a634a02d058fb
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code in i40e and i40evf is using an "IN_NETPOLL" flag that has never
added any value due to the fact that the Rx clean-up is handled in NAPI.
As such the flag was set, the queue was scheduled via NAPI, and then polled
from the netpoll controller and if any Rx packets were processed the were
processed in the wrong context.
In addition the flag itself just added an unneeded conditional to the
hot-path so it can safely be dropped and save us a few instructions.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Save a little stack space and remove unnecessary strncpy() with a little
string pointer.
Change-ID: Id2719d34710bfc273d3bb445fec085cd04276e88
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 will report Gen 1x1 in the PCI config space as it is on
IOSF bus, so skip the PCI bus link/speed check.
Change-ID: Icd5f5751dc7fb00dccf0d5dc5a0a644948e7062e
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Even though the device might be in MFP mode, if there's only one partition
enabled, then we still have plenty of interrupts for managing the Flow
Directory Sideband activity. This patch enables FD SB in this case.
This patch also reverses the sense of the conditional in order to remove
the negative logic.
Change-ID: I9edf211a6219fc8d159b4be9964f9fd7f4e00bc0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This version check only applies to very, very old firmware,
that only ran on A0 hardware, which we never shipped and don't
support in this driver anyway. Remove it, before somebody
gets hurt.
Change-ID: I3752d090ff488acf98ee76b075af961e9c968ee4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are several error messages that have been printing when there is
no functional issue. These messages should be available at debug message
level only.
Change-ID: Id91e47bf942c483563995f30d8705fa53acd5aa3
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add nlflags to the function comment for ndo_bridge_setlink.
Change-ID: I34c704f307f2a3f7bac3ca4b44e2a094d3d082d6
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unused members in the PHY structure and add a new member to store
all the capabilities the PHY has as reported by the FW. This information
will help us determine what speeds the device is capable of when link is
down.
Also add an enum to decode the PHY types the NVM is capable of.
Use the phy_types variable to determine what phy types are possible
when link is down instead of device id as it will be more accurate.
When on a backplane device, we do not support changing any settings,
however we should display all the phy_types we are capable of so if we
see a backplane dev ID set supported and advertised purely based on
the phy_types variable.
Change-ID: Ia75d560f1fcd30c54cbfb7458690c5867559a930
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a module_types variable to the link_info struct to save the module
information from get_phy_capabilities. This information can be used to
determine which speeds the module supports.
Also add a new function update_link_info which updates the module_types
parameter and then calls get_link_info. This function should be called
in place of get_link_info so that the module_types variable stays
up-to-date with the rest of the link information.
The EAS table does not reflect the values that are actually returned,
so instead, basing these values on the Ethernet compliance codes
specified in table 33 of SFF-8436 as these have been accurate.
Use the new variable in ethtool to differentiate between a 10G/1G dual
speed fiber module and a 10G only module.
Change-ID: Ib7585cce321319c10ce15180054c41a6cbd41389
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch moves the internal fw version and fw api version info to be
output in probe. The nvm version, etrack and oem version info are now
configured for output via ethtool -i.
Change-ID: I05d490093a7137dbefcdef263d014d1e5c9e83d0
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Flag the filter_mask parameter as __always_unused in the
ndo_bridge_getlink function.
Change-ID: Ifc1e99c7fb84bcbf81cf7b0ac891ad8ca956ffb2
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To help users and developers know what compile options
and hardware features are enabled at compile time, print
VxLAN is available.
Change-ID: I3162f3b7678dc725a597f964217920eb218b480b
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I found a code indent that was avoidable because a whole function is inside
an if block, reverse the if and move the code back a tab.
Change-ID: I9989c8750ee61678fbf96a3b0fd7bf7cc7ef300a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add missings spaces after declarations, remove another __func__ use,
remove uncessary braces, remove unneeded breaks, and useless returns,
and generally fix up some code.
Change-ID: Ie715d6b64976c50e1c21531685fe0a2bd38c4244
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's been some need for controlling the periodic link polling for
debugging link issues. This patch enables switching it off and on
through an ethtool private flag. The link poll remains on by default,
but can be turned off with
ethtool --set-priv-flags p261p1 LinkPolling off
and later turned back on with
ethtool --set-priv-flags p261p1 LinkPolling on
To check the current status, use
ethtool --show-priv-flags p261p1
Change-ID: I32e4ab654ff3eec90a06cf144899971b82d71c40
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch addresses an issue where multiple link up messages can be logged
resulting from aq link status timing when link properties are changed (fc,
speed, etc.); solved by using a single function to handle status printing
and adding a mechanism to track whether link state (up or down) has
actually changed.
Change-ID: Ied6ed6e49dc397c77d992adc0bc9ed3767152b9d
Signed-off-by: Matt Jared <matthew.a.jared@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where the PF's fdir filter table would have an
entry that the hw was unable to add. This notification happens in the hot
path, so instead of trying to fix it then, we note the location in the
failure case and delete it during regular fdir subtask callback. Without
this patch, a case can occur where an invalid entry gets replayed and a
valid one is not.
Change-ID: I67831c183b5d0309876de807cc434809b74c9cb7
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The interrupt enable function can be inlined by moving it to the header
file, which decreases the function call overhead for a frequently called
function.
Change-ID: I3214cc99593725768642680e7b8ce7e9bba7e44d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Keep track of how many times we ask the stack to linearize the
skb because the HW cannot handle skbs with more than 8 frags per
segment/single packet.
Change-ID: If455452060963a769bbe6112cba952e79e944b52
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When using something like "ip maddr add ..." to add another unicast mac
address to the netdev, the mac address comes into the set_rx_mode handler
in the multicast list whether it is a unicast or multicast address.
This was confusing the code when it was trying to search for addresses
that needed to be deleted from the VSI, because it was looking for the
VSI unicast address in the netdev unicast list. The result was that a
new unicast address would get added to the VSI list and then immediately
removed, and would never actually make it down into the hardware.
This patch removes the separation from unicast and multicast in the search
for filters to be deleted. It also simplifies the logic a little with a
jump to the bottom of the loop when an address is found. Now it doesn't
matter which netdev list the address is hiding in, we'll check them all.
Change-ID: Ie3685a92427ae7d2212bf948919ce295bc7a874c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously, the driver could call this function and have only true/false
returned, but false could mean multiple things like failure to read
or link was down. This change allows the caller to get all return values
in the call chain bubbled back to the source, which keeps information about
failures from being lost.
Also, in some unlikely scenarios, the firmware can become slow to respond
to admin queue (AQ) queries for link state. Should the AQ time out,
the driver can detect the state and avoid a link change when there
may have been none.
Change-ID: Ib2ac38407b7880750fb891b392fa77457fe6c21c
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During early development, we added the function name to all of the error
strings to make debugging simpler. Now that we've released the driver,
our users should have more comprehensible error messages. So tear the
roof off and give up the __func__. Ow.
Change-ID: I7e1766252c7a032b9af6520da6aff536bdfd533c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_init_pf_fcoe() didn't return anything except 0, it prints enough
error info already, and no driver logic depends on the return value,
so this can be void.
Change-ID: Ie6afad849857d87a7064c42c3cce14c74c2f29d8
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Early addition of new a device id.
Change-ID: I61a8c8556fdf4f5714be4e4089689e374f30293c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was disabling Wake-on-LAN by default and waiting for the user
to expressly turn it on. This patch has the driver turning on WoL from
the start if enabled in the hardware config, which matches the behavior
of our other drivers.
Change-ID: I43faedb907f8ba4d1a61b72a7c86072b97af12b1
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver still was not offloading TSO on GRE tunnels because
it forgot to set the GSO_GRE flag, causing lots of retransmits.
This fixes generic GRE traffic (like a tunnel added like below)
whereas before it would get 1Gb/s or less, now on a 10G adapter
it gets 8.7Gb/s.
ip ad ad 11.1.0.2/24 dev ens2f0
ip l set ens2f0 up
ip link add gre2 type gretap remote 11.1.0.1 local 11.1.0.2 dev ens2f0
ip l set gre2 up
ip ad ad 192.168.124.2/24 dev gre2
ping 192.168.124.1
netperf -H 192.168.124.1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In any case free the memory allocated before exiting.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-09-30
This series contains updates to i40e and i40evf only.
Vasily Averin provides a couple of rtnl lock/unlock fixes for both i40e
and i40evf.
Shannon provides several updates and fixes, first fixes up a type clash
in i40e_aq_rc_to_posix(), where the error codes are signed values, so we
need to treat them as such. Then fixes up a padding issue where an
extra byte is added in i40e_aqc_get_cee_dcb_cfg_v1_resp to directly
acknowledge the padding. Updated i40e to keep debugfs register read
and writes from accessing outside of the io-remapped space. Added
support and device id for another 20 GbE device.
Jesse fixes the transmit hand workaround code for ARM that was causing
Tx hangs to still occur occasionally when there really was no hang. Then
fixed the receive dropped counter to show up in netstat interface.
Refactor the interrupt enable function since it was always making the
caller add the base_vector from the VSI struct which is already passed
to the function. Fix kbuild warnings found in 0day build infrastructure
by adding a harmless cast to a dev_info(), also fix 32 bit build
warnings found by sparse.
Greg fixed a configuration error that results if a port VLAN is set
for a VF before the VF driver is loaded, so that when the VF driver is
loaded the port VLAN is ignored.
Mitch fixes the use of QOS field consistently in
i40e_ndo_set_vf_port_vlan(). Modified the init timing of the driver
to increase stability on load/unload and SR-IOV enable/disable cycles.
Anjali updates i40e to not collect VEB stats if they are disabled in the
hardware for performance reasons.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt enable function was always making the caller add
the base_vector from the VSI struct which is already passed to
the function. Just collapse the math into the helper function.
Change-ID: I54ef33aa7ceebc3231c3cc48f7b39fd0c3ff5806
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to performance reasons, VEB stats have been disabled in the hw. This
patch adds code to check for that condition before accumulating these
stats.
Change-ID: I7d805669476fedabb073790403703798ae5d878e
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add new device id and support for another 20Gb device.
Change-ID: Ib1b61e5bb6201d84953f97cade39a6e3369c2cf2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove a useless message that blathers on whenever a vxlan port is deleted.
Change-ID: If63fb8cf38e56cf433b68e498f11389de51919ba
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't let the debugfs register read and write commands try to access
outside of the ioremapped space. While we're at it, remove the use of
a misleading constant.
Change-ID: Ifce2893e232c65c7a76c23532c658f298218a81b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e rx_dropped counter was not showing up in netstat -i.
Add the right counter to be updated with the stats.
Change-ID: I4dd552e9995836099184f9d9a08e90edb591155f
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a port VLAN is set for a given virtual function (VF) before the VF
driver is loaded then a configuration error results in which the port
VLAN is ignored when the VF driver is subsequently loaded. This causes
the VF's MAC/VLAN filters to not use the correct VLAN filter. This
patch ensures that the port VLAN filter is considered at the right time
during configuration of the VF's MAC/VLAN filters.
Change-ID: I28f404cbc21a4c6d70a7980b87c77f13f06685a4
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously to this patch, the hardware was removing
VLAN tags from the inner header of VXLAN packets. The
hardware configuration can be changed to leave the
packet alone since that is what the linux stack
expects for this type of VLAN in VXLAN packet.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sync_vsi_filters function can be called directly under RTNL
or through the timer subtask without one. This was causing a deadlock.
If sync_vsi_filters is called from a thread which held the lock,
and in another thread the PROMISC setting got changed we would
be executing the PROMISC change in the thread which already held
the lock alongside the other filter update. The PROMISC change
requires a reset if we are on a VEB, which requires it to be called
under RTNL.
Earlier the driver would call reset for PROMISC change without
checking if we were already under RTNL and would try to grab it
causing a deadlock. This patch changes the flow to see if we are
already under RTNL before trying to grab it.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies the driver timeout logic by issuing a writeback
request via a software interrupt to the hardware the first time the
driver detects a hang. The driver was too aggressive in resetting a hung
queue, so back that off by removing logic to down the netdevice after
too many hangs, and move the function to the service task.
Change-ID: Ife100b9d124cd08cbdb81ab659008c1b9abbedea
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fixes bugs where the port is not receiving multicast or VLAN tagged
packets when in promiscuous mode. This can occur when a SW bridge is
created on top of the device.
This also fixes issues where the promiscuous behavior setting was not
being preserved across a reset caused by features being enabled or
disabled.
We are using defport instead of doing a true promiscuous mode because we do
not need to receive the SRIOV or VMDq VSI directed traffic which would suck
up bandwidth and is really not intended for the SW bridge.
In addition, with defport we get VLAN promiscuous behavior which is not
possible from the VSI level promiscuous setting.
Change-ID: Ie21985eac32d5af1c02e9d71c6430a90d5bab40f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump version and update the copyright year for i40evf.
Change-ID: Iddb81b9dba09f0dc57ab54937b5821ecdd721ff6
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The kernel notifies all VXLAN capable registered drivers, i.e. any
driver that implements ndo_add_vxlan_port(), of the addition of a
port so that the driver can track which ports are in use. There's
no need to log this - it just fills the system log with useless and
irksome noise.
Also, when failing to init SR-IOV interfaces the driver was printing the
same message twice. Just remove the inner printk and let the outer message
catch enable as well as the other failures.
Change-ID: Id5ecb1d425c2a357ee2bc1635dab24553831dade
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds capability to update per VEB per TC statistics and dump
it via ethtool. It also adds a structure to hold VEB per TC statistics.
The fields can be filled by reading the GLVEBTC_* counters.
Change-ID: I28b4759b9ab6ad5a61f046a1bc9ef6b16fe31538
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the driver flow to take into account legacy interrupts.
Over time we added code that assumes MSIX is the only mode that the
driver runs in. It also enables a legacy workaround to trigger SWINT
when the TX ring has non-cache aligned descriptors pending and interrupts
are disabled.
We work with a single vector in MSI mode too, so apply the same
restrictions as Legacy.
Change-ID: I826ddff1f9bd45d2dbe11f56a3ddcef0dbf42563
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We should be stopping the service task and flow director on
shutdown not on suspension.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sparse cries when we compare an __le16 to a u16, almost like it cares
about architectures other than x86. Weird. Use the le16_to_cpu macro to
make it stop crying.
Change-ID: Id068f4d7868a2d3df234a791a76d15938f37db35
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports IWARP, this patch handles checking for PE critical errors.
Since the driver doesn't support the IWARP interface for now, this patch
just does bare minimum to log a message oif a PE critical error
happens.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 supports offloading of outer UDP TX and RX checksum for tunneled
packets. This patch exposes the support and leaves it enabled by
default.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 fixes an issue from X710 where TX descriptor WB would not happen if
the interrupts were disabled. In order for the write backs to happen a
bit needs to be set in the dynamic interrupt control register called
WB_ON_ITR. With this feature, the SW driver need not arm SW interrupts to
work around the issue in X710.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 uses the admin queue to configure RSS. This patch adds the necessary
flow changes to configure RSS through AQ. It also adds the separate VMDQ2
lookup tables and hash key programming for X722.
X722 also exposes a different set of PCTYPES for RSS, this patch
accommodates those changes.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add capabilities flags specific to X722.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adding device ids for new hardware X722
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use macros for abstracting (1 << foo) to BIT(foo)
and (1ULL << foo64) to BIT_ULL(foo64) in order to match
better with kernel requirements.
NOTE: the adminq_cmd.h file was not modified on purpose because
of the dependency upon firmware for that file.
Change-ID: I73ee2e48c880d671948aad19bd53ca6b2ac558fc
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up a little confusion in reporting error status in phy and fcoe
setup error reports by separating the return status from the AQ error.
Add two decoder functions to make this easier.
Change-ID: I960bcdeef3978a15fec1cdb5eff781d5cbae42fb
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump.
Change-ID: I84573d9fa51effc5b29bf5b8c74e3cc8b2673f48
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change a warning message to indicate what may have really happened when
the init_shared_code call fails.
Change-ID: I616ace40fed120d0dec86dfc91ab2d7cde466904
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes some #ifdef's that should not be there. They
were stopping code that is needed from being compiled in.
With these #ifdef's removed, changes are needed in the driver
to fix some compile errors: adding missing parameters to
the definition of ndo_bridge_setlink and a ndo_dflt_brige_getlink call.
Change-ID: I5516614e1bc50b6bca0647cef971bc96161ba2de
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Flex10 device/function capability has been upgraded to include
information needed to support Flex-10 configurations. This patch adds new
fields to the i40e_hw_capabilities structure and updates
i40e_parse_discover_capabilities functions to extract them from the AQ
response. Naming convention has changed to use flex10 mode instead of
existing mfp_mode_1.
Change-ID: I305dd888866985a30293acb3fb14fa43ca6b79ea
Signed-off-by: Pawel Orlowski <pawel.orlowski@intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the driver can dynamically enable/disable FD ATR and SB features,
these stats help keep track of the current state and along with
fd_flush count provide a means to debug what could be going on
with the flow director filters. This will take away the need for
being verbose in our debug logs with respect to FD.
Change-ID: I29224f750fe6602391043655d18996570720377d
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e supports UDP tunnel headers up to 80 bytes in length, so
this adds a check to ensure that it doesn't try to offload
packets that exceed that.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One more missing piece of the puzzle. Add vlan dump support to switchdev
port's bridge_getlink. iproute2 "bridge vlan show" cmd already knows how
to show the vlans installed on the bridge and the device , but (until now)
no one implemented the port vlan part of the netlink PF_BRIDGE:RTM_GETLINK
msg. Before this patch, "bridge vlan show":
$ bridge -c vlan show
port vlan ids
sw1p1 30-34 << bridge side vlans
57
sw1p1 << device side vlans (missing)
sw1p2 57
sw1p2
sw1p3
sw1p4
br0 None
(When the port is bridged, the output repeats the vlan list for the vlans
on the bridge side of the port and the vlans on the device side of the
port. The listing above show no vlans for the device side even though they
are installed).
After this patch:
$ bridge -c vlan show
port vlan ids
sw1p1 30-34 << bridge side vlan
57
sw1p1 30-34 << device side vlans
57
3840 PVID
sw1p2 57
sw1p2 57
3840 PVID
sw1p3 3842 PVID
sw1p4 3843 PVID
br0 None
I re-used ndo_dflt_bridge_getlink to add vlan fill call-back func.
switchdev support adds an obj dump for VLAN objects, using the same
call-back scheme as FDB dump. Support included for both compressed and
un-compressed vlan dumps.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SRIOV is enabled we need to be in VEB mode not VEPA mode at probe.
This fixes an NPAR bug when SRIOV is enabled in the BIOS.
Change-ID: Ibf006abafd9a0ca3698ec24848cd771cf345cbbc
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The patch fixes a bug in the default configuration which
prevented a software bridge loaded on the PF interface from
working correctly because broadcast packets are incorrectly
looped back.
Fix the general case, by loading the driver in VEPA mode Until a
VF or VMDq VSI is added. This way loopback on the Main VSI is
turned off until needed and can resolve the issue of unnecessary
reflection for users that do not have VF or VMDq VSIs setup.
The driver must now coordinate the loopback setting for the Flow
Director (FDIR) VSI to make sure it is in sync with the current
VEB or VEPA mode setting.
The user can still switch bridge modes from the bridge commands and
choose to be in VEPA mode with VF VSIs. Because of hardware
requirements, the call to switch to VEB mode when no VF/VMDqs are
present will be rejected.
NOTE: This patch uses BIT_ULL as that is preferred going forward,
a followup patch in the lower priority queue to net-next will fix
up the remaining 1 << usages.
Change-ID: Ib121ddb18fe4b3c4f52e9deda6fcbeb9105683d1
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump.
Change-ID: I54ec2787a9fead5e18447078f26e5dd27f01da44
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These are not useful unless SV is happening as there is a FD flush counter
that tracks this.
Change-ID: If2655b5a29687247d03a51d35f69854bbeb711ce
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We can use the stat index macro directly, a variable is not required.
Change-ID: I19f08ac16353dc0cd87a1a8248d714e15a54aa8a
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a 3rd dynamic filter counter to track Tunneled ATR hits separately.
Ethtool port stat "fdir_atr_tunnel_match"
Change-ID: Idd978b6db2a462b5722397cd2ffd04ef055f8655
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When PFC is enabled for any UP in single TC configuration the driver didn't
collect the PFC XOFF RX stats. Though a single TC with PFC enabled is not a
common scenario do not prevent the driver from collecting stats if firmware
indicates that PFC is enabled.
Change-ID: Ie20bd58b07608b528f3c6d95894c9ae56b00077a
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: e5a55a8987 ("net: create generic bridge ops")
Fixes: 815cccbf10 ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Sathya Perla <sathya.perla@emulex.com>
CC: Subbu Seetharaman <subbu.seetharaman@emulex.com>
CC: Ajit Khaparde <ajit.khaparde@emulex.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: intel-wired-lan@lists.osuosl.org
CC: Jiri Pirko <jiri@resnulli.us>
CC: Scott Feldman <sfeldma@gmail.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump.
Change-ID: Id14baae72332d0f1a9bc5d351ea1a85cb0295ec3
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The init_interrupt_scheme function had a possible failure
path to allocate memory that was found by smatch.
This adds the correct handling to the function to abort
probe if the memory allocation fails.
Change-ID: I2bf1d826a244209619da4c452d0d58b3eb5e26a3
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump.
Change-ID: I7dc88baa33264e5919bc938adf76706573209432
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This does not affect the Virtual channel API as such but it changes the
meaning of what is communicated to the VSI resource struct as vsi_id.
Earlier vsi_idx was being passed in, which was the index in the PF's VSI
array. Now we pass vsi_id as communicated by the FW to the driver.
This will help with future expansion of VF and FW communication.
With this in place now the VF and Virtual channel driver change to move over
to VSI id use is complete and is validated.
Change-ID: I14246ef82b3b3dc1fa76291d2dd0c05d12cedb7c
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some cases, the hardware would continue to try to access the FDIR
ring after entering D3Hot state, which would cause either PCIe errors or
NMIs, depending upon system configuration.
Explicitly stop FDIR in our shutdown routine to eliminate this
possibility.
Change-ID: Ib98060d6352ec595ab9a78bfe252675a9fa5d8bc
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the VXLAN ports are added and removed, the messaging was giving some
bogus index info, the port was always '0' for the delete, and the message
text style didn't match other messages in the driver. Also, there was an
over-use of the tertiary statement which made reading a little harder
than necessary.
Change-ID: Ie805182a697b8b4c12024403ada87fd4e4fa2358
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several memcpys are not necessary and can be changed to structure
assignments. Struct assignments are always type safe so this
is preferable.
Change-ID: I7daf45a4b5e799c686b9d5c8ba9db047584ab82b
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
HMC_ERRORINFO and HMC_ERRORDATA helps explain the cause of HMC error.
Change-ID: I053bbc175a5f4c5c3e9ec2ea7400d5c56aaa4ec1
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new devices need a new device ID some other defines to
handle the new 20G speed for KR2.
Change-ID: I03f717e364afe59657e8c9ce5ffaad856b4b21df
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Quit complaining about a couple of events that we actually expect to see
during an NVM update.
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump PF version to 1.2.37 and VF version to 1.2.25
Change-ID: I0287a750408250dc055c03e1f744fd5f0caefd68
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Joe Perches pointed out that we were inconsistent in the use of
PF vs pf or VF vs vf in our driver code. Since acronyms are usually
capitalized to denote that it is an acronym, changed all references to
be consistent throughout the code.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The use of configfs is not allowed in network drivers. Strip the code that
uses it.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.12 and i40evf to 1.2.6.
Change-ID: I641871da3a9abd396b28eda5744a4d68493c1400
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We initialize the pf->rss_size_max in sw_init now
and hence this code can be simplified.
Change-ID: I1a7abc837604a40bc65e6c6b21190b909ed6bb21
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since GLQF_FDCNT_0 register now has the right offset, use it to simplify our
FD flush flow.
If the filter add error happens to be for SB we just auto disable SB.
If filter error happens to be for ATR, auto disable ATR and mark
the state to FD_FLUSH_REQUESTED. Which gets cleared when flush completes.
If we are entering flush too quickly (< 30 seconds) and we have quite
a few SB rules, its time to disable ATR for good. Since SB + ATR rules
is most likely making the FD table unstable.
ATR can be re-enabled by turning ntuple off (ethtool -K ntuple off)
and will remain off after turning ntuple on till it gets unstable again.
Change-ID: I2154a2e0a5d44851a2f0eb8731e2f1d4a4d1acbc
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since changes made to enable or disable loopback for all VSIs, not only SR-IOV
or PCIOV, then it became necessary to move the associated functions to main
file - so that other non-SRIOV supported driver can take advantage of the
changes.
Change-ID: I59a49fd23a6136acda5e16f8d1e5ac7fd9c5fc05
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The initial problem solved here is that the vector allocation was trying
too hard to save vectors for VMDq, to the point of not giving the PF enough
when in a tight situation such as an NPAR partition. This change makes
sure that the PF will get all the queues and vectors it wants to fill
out its destiny. Essentially, nothing is specially reserved for VMDq,
it simply gets whatever is left after the PF, FCoE, and FD sideband get
what they want.
Additionally, the calculations for the reservations were harder to follow
than necessary, so I've made it more straight forward.
Change-ID: I99b384f104535b686c690b8ef0a787559485c8d4
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This series of code was repeated twice, remove one of them.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A sparse complaint in i40e_debug_aq in a funky buffer write goes away by
straightening out the code out to something less convoluted.
Also fix some other sparse warnings while we are at it, making some
functions static and using NULL instead of 0.
Change-ID: I93907534fe1f1f675830774b3d14ecf1c6ffc9a0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As pointed out by Ben Hutchings, ioremap uses unsigned long as
its parameter type, so we should be using that instead of u32
or int.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump i40e to 1.2.11 and i40evf to 1.2.5
Change-ID: Ie13375941606b0a027e5b5dbc235f5f5f03b75c8
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the IRQ tracking setup and teardown into the same routines that
do the IRQ setup and teardown. This keeps like activities together and
allows us to track exactly the number of vectors reserved from the OS,
which may be fewer than are available from the HW.
Change-ID: I6b2b1a955c5f0ac6b94c3084304ed0b2ea6777cf
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For future device support we do not want to map the whole CSR space since some
of it is mapped by other drivers with different mapping methods.
Note: As a side effect, the flash region (if exposed through the memory map)
gets unmapped too since it follows the future use region.
Change-ID: Ic729a2eacd692984220b1a415ff4fa0f98ea419a
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix some double blank lines and un-split a function declaration that all
fits on one line. Also make i40e_get_priv_flags static.
Change-ID: I11b5d25d1153a06b286d0d2f5d916d7727c58e4a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During resets (possibly caused by a Tx hang) the driver would
accidentally clear the XPS mask for all queues back to 0.
This caused higher CPU utilization and had some other performance impacts
for transmit tests.
Change-ID: I95f112432c9e643a153eaa31cd28cdcbfdd01831
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent changes to the driver initialization have caused the BW
configurations to not take effect. We use a BW configuration read and
write back to "kick" the Tx scheduler into action.
Change-ID: I94ab377c58d3a3986e3de62b6c199be3fd2ee5e6
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-03-03
This series contains updates to fm10k, i40e and i40evf.
Matthew updates the fm10k driver by cleaning up code comments and whitespace
issues. Also modifies the tunnel length header check, to make it more robust
by calculating the inner L4 header length based on whether it is TCP or UDP.
Implemented ndo_features_check() that allows drivers to report their offload
capabilities per-skb.
Neerav updates the i40e driver to skip over priority tagging if DCB is not
enabled. Fixes an issue where the driver is not flushing out the
DCBNL app table for applications that are not present in the local DCBX
application configuration TLVs. Fixed i40e where, in the case of MFP
mode, the driver was returning the incorrect number of traffic classes
for partitions that are not enabled for iSCSI. Even though the driver
was not configuring these traffic classes in the transmit scheduler for
the NIC partitions, it does use this map to setup the queue mappings.
Shannon updates i40e/i40evf to include the firmware build number in the
formatted firmware version string.
Akeem adds a safety net (by adding a 'default' case) for the possible
unmatched switch calls.
Mitch updates i40e to not automatically disable PF loopback at runtime,
now that we have the functionality to enable and disable PF loopback. This
fix cleans up a bogus error message when removing the PF module with VFs
enabled. Adds a extra check to make sure that the indirection table
pointer is valid before dereferencing it.
Anjali enables i40e to enable more than the max RSS qps when running in a
single TC mode for the main VSI. It is possible to enable as many as
num_online_cpus(). Adds a firmware check to ensure that DCB is disabled for
firmware versions older than 4.33. Updates i40e/i40evf to add missing
packet types for VXLAN offload. Updated i40e to be able to handle varying
RSS table size for each VSI, since all VSI's do not have the same RSS table
size.
v2: Dropped previous patch #9 "i40e/i40evf: Add capability to gather VEB
per TC stats" since the stats should be in ethtool and not debugfs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Module dependencies are broken in the case where CONFIG_I40E=y and
CONFIG_CONFIGFS_FS=m. This fixes the broken dependency.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump i40e to 1.2.10 and i40evf to 1.2.4
Change-ID: I48aa64df05fcc8356e7026f3a9e69ecf78d0c785
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In case of MFP mode the driver was returning incorrect number of TCs
for partitions that are not enabled for iSCSI. Though the driver does
not configure these TCs in the Tx scheduler for the NIC partitions;
it does use this map to setup the queue mappings.
This patch fixes this and keeps all the NIC partitions to the default
PF TC i.e. TC0.
Change-ID: Iede214c907e7bac1356e999049b9f642759512b3
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With changes to default number of queue pairs that the interface comes up with
from 1 per online CPU to 1 per lan_msix, we need to make sure we recalculate
rss_size. We will now recalculate rss_size based on number of queues enabled in
the VSI.
Without this fix if the max_lan_msix < num_online_cpu we will be coming up
with fewer queues but will be populating rss_size based on num_online_cpus.
This will result in packets getting silently dropped because RSS LUT has queues
that are not enabled.
Change-ID: Ifac8796ce1be1758bb0c34f38dbf4a3a76621e76
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since all VSIs don't have the same RSS table size,
have one for each VSI instead of having a single define
for RSS table size
Change-ID: Ic2c7c66e4a389d4b6c8841a707510a9735041f02
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue where the driver is not flushing out the
DCBNL app table for applications that are not present in the local
DCBX application configuration TLVs.
Change-ID: I1f1ee04c81c145071b2ab15657546eb10b81fadb
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For FW < 4.33 DCB should be disabled.
Also Autoneg workaround to avoid Rx stall is still needed for FW < 4.33.
Change-ID: Iff36ad86be2f597e7701096014d6d094332a9a21
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When running in a single TC mode the HW can be configured to enable more
than max RSS qps for the Main VSI. This patch makes it possible to
enable as many as num_online_cpus().
ethtool -L can still be used to reconfigure number of qps
to a smaller value.
Change-ID: I3e2df085276982603d86dfd79477c0ada8d30b8f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some cases, the hardware would continue to try to access the FDIR
ring after entering D3Hot state, which would cause either PCIe errors or
NMIs, depending upon system configuration.
Explicitly stop FDIR in our shutdown routine to eliminate this
possibility.
Change-ID: I1bd9fc7fd8f151fe24cad132ac9adddab923e3af
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Combine the ICR0 shutdown with the standard interrupt shutdown, and
add the interrupt clearing to the PCI shutdown path.
This prevents the driver from allowing stray interrupts or causing
system logs from un-handled interrupts.
Change-ID: I48f6ab95cad7f8ca77c1f26c92a51cc1034ced43
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As part of DCB reconfiguration flow if the Tx queue disable times out
then issue a PF reset to do some level of recovery.
Change-ID: I7550021c55bff355351c0365e61e1f05fcaff46d
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When DCB is reconfigured to single TC the driver did not reset the
Tx ring Qset handle to the correct mapping; which caused Tx queue
disable timeouts.
Change-ID: I4da5915ec92a83c281b478d653fae6ef1b72edfe
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the driver or hardware gets less interrupt vectors than the actual
number of CPU cores, limit the queue count for the priority queue
traffic class (TC) queues.
This will fix a warning with multiple function mode where systems
regularly have more cores than vectors.
Also add extra comment for readability.
Change-ID: I4f02226263aa3995e1f5ee5503eac0cd6ee12fbd
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds check to bail out if device is already down when checking
for Tx hang subtask.
Change-ID: I3853fb7a6d11cb9a4c349b687cb25c15b19977a0
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.9 and i40evf 1.2.3
Also update the copyright year.
Change-ID: I345d777e94abd0acffe6a28793f675d251a86299
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the RX routine in use to the features log message.
Change-ID: Ifbbf28fb7f42b9a3d2828586488e9e6331107dd5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for bridge offload ndo_ops getlink and setlink to
enable bridge hardware mode as per the mode set via IFLA_BRIDGE_MODE.
The support is only enabled in case of a PF VSI and not available for
any other VSI type.
By default the i40e driver inserts a bridge as part of the bring-up
when a FDIR type VSI and/or a FCoE VSI is created. This bridge is
created in VEB mode by default i.e. after creating the bridge using
"Add VEB" AQ command the loopback for the PF's default VSI is enabled.
The patch adds capability where all the VSIs created as downlink to
the bridge inherits the loopback property and enables loopback only
if the uplink bridge is operating in VEB mode.
Hence, there is no need to explicitly enable loopback as part of
allocating resources for SR-IOV VFs and call to do that has been
removed.
In case a user-request is made either via "bridge" utility or using
the bridge netlink interface that requires to change the hardware
bridge mode then that would require a PF reset and rebuild of the
switch hierarchy.
Also update the copyright year.
Change-ID: I4d78fc1c83158efda29ba7be92239b74f75d6d25
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add configfs controls to get, set and commit NPAR BW configurations.
We export three controls:
min_bw - Can take a value from 0 to 100 inclusive
max_bw - Can take a value from 1 to 100 inclusive
commit - A write-only control that accepts only a value of 1 and will
cause the BW settings to be permanently committed to NVM so
that they are persistent across power cycles and system
resets
The BW values are relative and are expressed as percentages. For more
information on the interpretation of the BW settings see the Dell
specifications for NPAR.
Also update the copyright year.
Change-ID: Id7496ca65630b5037e32ba6a5a748fbc1632881b
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-By: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We need to be able to get, set and commit permanently the NPAR
partition BW configuration through configfs. These are necessary
precursor functions for that feature.
Also update the copyright year.
Change-ID: I9d5ca160a9288145f1dd2042994028679fff55f3
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When an IOMMU is in use, the packet split receive path shows a distinct
advantage over the single-buffer path because it minimizes DMA mapping
and unmapping. However, this is not an advantage for systems with no
IOMMU. At init time, check to see if an IOMMU is enabled and enable
packet split receives.
Change-ID: I4f70d2e9c31bbea3dc8fd0c5734959a6e6602210
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a requested speed variable to the link_status struct to store the
last speeds we requested from the firmware (the speeds the FW will be
advertising with if autoneg is enabled).
Use the advertised speed settings in get_settings in ethtool now that
we have it. Also set the requested speed settings in set_settings in
ethtool as they are requested and initialize them in probe based on what
the firmware remembers as the last requested speeds.
To accommodate some longer lines in this new code, and improve
readability I have added two functions i40e_get_settings_link_up
and i40e_get_settings_link_down which get_settings now calls first.
It then does all of the settings that happen regardless of link
state. Some PHY types that supported the same settings were also combined.
Also update the copyright year.
Change-ID: Ica0c5ac81b6069ea6a7406fce7482f7816d4455c
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.8 and i40evf to 1.2.2
Change-ID: I64f47c3367ea8ff2a53068e895d7a1f60726c871
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
An_enable was never used only set so lets remove it. The function
update_link_info only did two things, call get_link_info and set
an_enabled. Therefore we should also remove update_link_info and
change all references to it to get_link_info.
Change-ID: Ie3022680fa7a94bfd495a4f5fc76a73701d85569
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We shouldn't trigger another EMPR when we receive an EMPR event.
This patch handles EMPR event reception with a different state
so that we can do the right thing for NVM.
Change-ID: I9cac70b3658600f016a65beb6fb157e1c1f9adf9
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some registers have been removed so take them out and
stop updating and looking at them.
Change-ID: I33da922c8de993a94dd8b8d8a2ae2146b8ca1a27
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use #defined VSI connection type values instead of using magic numbers.
Change-ID: I2f6cf7bf394d391e1c0fe61779e9e4ad8858154a
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Split the receive hot path code into two, one for packet split and one
for single buffer. This improves receive performance since we only need
to check if the ring is in packet split mode once per NAPI poll time,
not several times per packet. The single buffer code is further improved
by the removal of a bunch of code and several variables that are not
needed. On a receive-oriented test this can improve single-threaded
throughput.
Also refactor the packet split receive path to use a fixed buffer for
headers, like ixgbe does. This vastly reduces the number of DMA mappings
and unmappings we need to do, allowing for much better performance in
the presence of an IOMMU.
Lastly, correct packet split descriptor types now that we are actually
using them.
Change-ID: I3a194a93af3d2c31e77ff17644ac7376da6f3e4b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stop the service task in the shutdown handler, preventing it from
accessing the admin queue after it had been closed. This fixes a panic
that could occur when the system was shut down with a lot of VFs
enabled.
Change-ID: I286735e3842de472385bbf7ad68d30331e508add
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This I40E_FCOE block increments v_budget before it has been initialized,
then v_budget gets overwritten a few lines later. This patch just
reorders the code hunks in what I believe was the intended sequence.
Coverity: CID 1260099
Signed-off-by: John W Linville <linville@tuxdriver.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.6 and i40evf to 1.2.0 version.
Change-ID: Ice127eee3a5a5d1b8765d83cff8c30f9f3b1bc32
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add parsing and reporting of iSCSI capability for a given device or
function.
Also add support for iSCSI partition type with DCB in NPAR mode.
In this mode it is expected that software would configure both the LAN
and iSCSI traffic classes for the iSCSI partition; whereas all the NIC
type partitions will use LAN TC (TC0) only.
Hence, the patch enables querying of DCB configuration in MFP mode and
configures TCs for iSCSI partition type.
Though NIC type partitions may not have more than 1 TC enabled for them
the port may have multiple TCs enabled and hence I40E_FLAG_DCB_ENABLED
will be set/reset on all the partitions based on number of TCs on the
port. This is required as in DCB environment it is expected that all
traffic will be priority tagged.
Change-ID: I8c6e1cfd46c46d8a39c57d9020d9ff8d42ed8a7d
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Disable firmware LLDP agent for NICs with firmware version lower than
v4.3. Added a message when driver disables the firmware LLDP agent on
such NICs.
Change-ID: Ia8abf89439c70cb50e23db82753d7d282265506b
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We should not blindly enable the PTP interrupt flags for all PFs. We
should only enable the PTP interrupt in PFs which have enabled
PTP.
Change-ID: I051a17cae4c199a2f3cf7852266e27eda6630525
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 1.2.5 and i40evf to 1.0.7.
Change-ID: I622556829056e3ed42d3b9d285fc5ffb693b21cc
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch creates a define for interrupt name string configuration that
is large enough to contain full bus/slot info, rather than just netdev->name.
Change-ID: Iaac0d23dfb8526defeed69d91cea85ed4a50ddb2
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need to give up in the reset/rebuild process if the DCB setup failed,
so handle it here the same as in the probe setup. Also adjust the log strings
a little to look less scary.
Change-ID: I57308d703047e61d3f1a5e471ea77be232444ca0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where the /proc/interrupts descriptions
from the msix configuration were truncating the needed bus info,
making it hard to distinguish configuration from port to port.
This patch increases the string buffer size in order to allow the
full data to be displayed and sync's the text formatting of the misc
and fdir interrupt names
Change-ID: Ib01d6c61fb3f4ac70fbdf5bcc520b22638ea54b7
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure we only allow SR/IOV on the master PF of a port in multifunction
mode. This should be the case anyway based on the num_vfs configured in
the NVM, but this will help make sure there's no question. If we're not
in multifunction mode the partition_id will always be 1.
Change-ID: I8b2592366fe6782f15301bde2ebd1d4da240109d
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
