* Add dummy exynos4210_tmu_set_trip_hyst() helper.
* Add ->tmu_set_trip_temp and ->tmu_set_trip_hyst methods to struct
exynos_tmu_data and set them in exynos_map_dt_data().
* Move trips setting to exynos_tmu_initialize().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Set trips in ascending order in exynos7_tmu_initialize() (it should
make no difference in driver operation). This prepares the driver
code to moving trips setting from ->tmu_initialize method to
exynos_tmu_initialize().
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Use ->get_trip_[temp,hyst] methods instead of using trips structure
directly in all ->tmu_initialize method implementations.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Move ->tmu_clear_irqs call from ->tmu_initialize method to
exynos_tmu_initialize().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Clear IRQs after enabling thermal tripping (it should make no
difference in driver operation). This prepares the driver code
to moving IRQs clearing call from ->tmu_initialize method to
exynos_tmu_initialize().
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
All implementations of ->tmu_initialize always return 0 so make
the method void and convert all implementations accordingly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
On Exynos4210 one-point trimming is always used and data->temp_error1
is equal to 75. Therefore temp_to_code() will never return negative
value for the reference temperature conversion.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
of_thermal_get_ntrips() may return value bigger than supported
by a given SoC (i.e. on Exynos5422/5800) so fix the code to not
iterate the loop for i values >= data->ntrip.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Fix sanitize_temp_error() to handle Exynos7 SoCs and then use it in
exynos7_tmu_initialize().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
STATUS register is present on all SoCs so move its checking into
exynos_tmu_initialize().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
* Check for critical trip point existence in exynos_tmu_initialize()
so it is checked on all SoCs (except Exynos5433 for now).
* Use dev_err() instead of pr_err().
* Fix dev_err() to reference "device tree" not "of-thermal.c".
* Remove no longer needed check from exynos4412_tmu_initialize().
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
* Check for trip points existence in exynos_tmu_initialize() so it is
checked on all SoCs.
* Use dev_err() instead of pr_err().
* Fix dev_err() to reference "device tree" not "of-thermal.c".
* Remove no longer needed checks from exynos4210_tmu_initialize() and
get_th_reg().
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add missing clearing of the previous value when setting rising
temperature threshold.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The Exynos5440 is not actively developed, there are no development
boards available and probably there are no real products with it.
Remove wide-tree support for Exynos5440.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
[b.zolnierkie: ported over driver changes]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
exynos_tmu.h is used only by exynos_tmu.c so there is no need
for a separate include file.
Also while at it remove no longer needed cpu_cooling.h include.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Since calibration type for temperature is SoC (not platform) specific
just move it from platform data to struct exynos_tmu_data instance.
Then remove parsing of samsung,tmu_cal_type property. Also remove no
longer needed platform data structure.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Since pdata gain values are SoC (not platform) specific just move
it from platform data to struct exynos_tmu_data instance. Then
remove parsing of samsung,tmu_gain property.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Since pdata reference_voltage values are SoC (not platform) specific
just move it from platform data to struct exynos_tmu_data instance.
Then remove parsing of samsung,tmu_reference_voltage property.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Since pdata efuse values are SoC (not platform) specific just move
them from platform data to struct exynos_tmu_data instance. Then
remove parsing of samsung,tmu[_,min_,max]_efuse_value properties.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
All SoCs use the same value (4) for the noise cancel mode so just
make it explicit and remove parsing of samsung,tmu_noise_cancel_mode
property.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
All SoCs use the same values (25, 85) for trim points (except
Exynos5440 which currently specifices value 70 for the second trim
point -> it seems to be a mistake because documentation uses value
85 and two points based trimming has never been used by the driver
for this SoC anyway) so just make it explicit and remove parsing of
samsung,tmu_[first,second]_point_trim properties.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Trimming (one point based or two points based) is always used for
the temperature calibration and the default non-trimming code is
never reached. Remove it and then remove no longer needed parsing
of samsung,tmu_default_temp_offset property.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Remove unused "type" field from struct exynos_tmu_platform_data.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Device context's field data->soc is currently obtained by comparing
of_compatible's. Provide soc_type as .data field in device's match
table, as it is done in most drivers.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
tmu_read() in case of Exynos4210 might return error for out of bound
values. Current code ignores such value, what leads to reporting critical
temperature value. Add proper error code propagation to exynos_get_temp()
function.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: stable@vger.kernel.org # v4.6+
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When thermal sensor is not yet enabled, reading temperature might return
random value. This might even result in stopping system booting when such
temperature is higher than the critical value. Fix this by checking if TMU
has been actually enabled before reading the temperature.
This change fixes booting of Exynos4210-based board with TMU enabled (for
example Samsung Trats board), which was broken since v4.4 kernel release.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 9e4249b403 ("thermal: exynos: Fix first temperature read after registering sensor")
CC: stable@vger.kernel.org # v4.6+
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The thermal_zone_of_device_ops structure is only passed as the fourth
argument to thermal_zone_of_sensor_register, which is declared as const.
Thus the thermal_zone_of_device_ops structure itself can be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The property samsung,tmu_cal_mode is not used and not used. We can
safely remove it.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Added one additional parameter to thermal_zone_device_update() to provide
caller with an optional capability to specify reason.
Currently this event is used by user space governor to trigger different
processing based on event code. Also it saves an additional call to read
temperature when the event is received.
The following events are cuurently defined:
- Unspecified event
- New temperature sample
- Trip point violated
- Trip point changed
- thermal device up and down
- thermal device power capability changed
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The driver doesn't check if the regulator_get_optional return value is
-EPROBE_DEFER so it will wrongly assume that the regulator couldn't be
found just because the regulator driver wasn't registered yet, i.e:
exynos-tmu 10060000.tmu: Regulator node (vtmu) not found
In this case the return value should be propagated to allow the driver
probe function to be deferred until the regulator driver is registered.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The Exynos TMU DT binding says that the vtmu-supply is optional but the
driver uses devm_regulator_get() that creates a dummy regulator if it's
not defined in the DT. For example the following message is in the log:
10060000.tmu supply vtmu not found, using dummy regulator
Use the optional version of regulator_get() that doesn't create a dummy
regulator and instead returns a -ENODEV errno code. Since it's expected
that a regulator may not be defined and the driver will inform about it:
exynos-tmu 10060000.tmu: Regulator node (vtmu) not found
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When DeviveTree contains more trip-points than SoC can configure
(usually more than four) and polling mode is not enabled, then the
remaining trip-points will be silently ignored. No interrupts will be
generated for them.
This might be quite dangerous when one provides DTB with a
non-configurable critical trip-point, like (assuming four supported
thresholds in TMU):
- alert @50 C (type: active),
- alert @60 C (type: active),
- alert @70 C (type: active),
- alert @80 C (type: active),
- critical @120 C (type: critical) <- no interrupts generated.
This is a mistake in DTB so print a message in such case.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The devres.o gets linked if HAS_IOMEM is present so on ARCH=um
allyesconfig (COMPILE_TEST) failed on many files with:
drivers/built-in.o: In function `kirkwood_thermal_probe':
kirkwood_thermal.c:(.text+0x390a25): undefined reference to `devm_ioremap_resource'
drivers/built-in.o: In function `exynos_tmu_probe':
exynos_tmu.c:(.text+0x39246b): undefined reference to `devm_ioremap'
The users of devm_ioremap_resource() which are compile-testable should
depend on HAS_IOMEM.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Pull thermal updates from Zhang Rui:
- Implement generic devfreq cooling mechanism through frequency
reduction for devices using devfreq. From Ørjan Eide and Javi
Merino.
- Introduce OMAP3 support on TI SoC thermal driver. From Pavel Mack
and Eduardo Valentin.
- A bounch of small fixes on devfreq_cooling, Exynos, IMX, Armada, and
Rockchip thermal drivers.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (24 commits)
thermal: exynos: Directly return 0 instead of using local ret variable
thermal: exynos: Remove unneeded semicolon
thermal: exynos: Use IS_ERR() because regulator cannot be NULL
thermal: exynos: Fix first temperature read after registering sensor
thermal: exynos: Fix unbalanced regulator disable on probe failure
devfreq_cooling: return on allocation failure
thermal: rockchip: support the sleep pinctrl state to avoid glitches in s2r
dt-bindings: rockchip-thermal: Add the pinctrl states in this document
thermal: devfreq_cooling: Make power a u64
thermal: devfreq_cooling: use a thermal_cooling_device for register and unregister
thermal: underflow bug in imx_set_trip_temp()
thermal: armada: Fix possible overflow in the Armada 380 thermal sensor formula
thermal: imx: register irq handler later in probe
thermal: rockhip: fix setting thermal shutdown polarity
thermal: rockchip: fix handling of invalid readings
devfreq_cooling: add trace information
thermal: Add devfreq cooling
PM / OPP: get the voltage for all OPPs
tools/thermal: tmon: use pkg-config also for CFLAGS
linux/thermal.h: rename KELVIN_TO_CELSIUS to DECI_KELVIN_TO_CELSIUS
...
The 'ret' variable in exynos5440_tmu_initialize() is initialized to 0
and returned as is. Replace it with direct return statement. This also
fixes coccinelle warning:
drivers/thermal/samsung/exynos_tmu.c:611:5-8: Unneeded variable: "ret". Return "0" on line 654
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The NULL check in probe's error path is not needed because in that time
the regulator cannot be NULL (regulator_get() returns valid pointer or
ERR_PTR).
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Thermal core could not read the temperature after registering the
thermal sensor with thermal_zone_of_sensor_register() because the driver
was not yet initialized.
The call trace looked like:
exynos_tmu_probe()
thermal_zone_of_sensor_register()
of_thermal_set_mode()
thermal_zone_device_update()
exynos_get_temp()
if (!data->tmu_read) return -EINVAL;
exynos_map_dt_data()
data->tmu_read = ...
This produced an error in dmesg:
thermal thermal_zone0: failed to read out thermal zone (-22)
Register the thermal_zone_device later, after parsing Device Tree and
enabling necessary clocks, but before calling exynos_tmu_initialize()
which uses the registered thermal_zone_device.
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 3b6a1a805f ("thermal: samsung: core: Exynos TMU rework to use device tree for configuration")
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
During probe if the regulator could not be enabled, the error exit path
would still disable it. This could lead to unbalanced counter of
regulator enable/disable.
The patch moves code for getting and enabling the regulator from
exynos_map_dt_data() to probe function because it is really not a part
of getting Device Tree properties.
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 5f09a5cbd1 ("thermal: exynos: Disable the regulator on probe failure")
Cc: <stable@vger.kernel.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The value of emul_con was getting overwritten if the selected soc is
SOC_ARCH_EXYNOS5260. And so as a result we were reading from the wrong
register in the case of SOC_ARCH_EXYNOS5260.
Fixes: 488c7455d7 ("thermal: exynos: Add the support for Exynos5433 TMU")
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The thermal code uses int, long and unsigned long for temperatures
in different places.
Using an unsigned type limits the thermal framework to positive
temperatures without need. Also several drivers currently will report
temperatures near UINT_MAX for temperatures below 0°C. This will probably
immediately shut the machine down due to overtemperature if started below
0°C.
'long' is 64bit on several architectures. This is not needed since INT_MAX °mC
is above the melting point of all known materials.
Consistently use a plain 'int' for temperatures throughout the thermal code and
the drivers. This only changes the places in the drivers where the temperature
is passed around as pointer, when drivers internally use another type this is
not changed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Peter Feuerer <peter@piie.net>
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Peter Feuerer <peter@piie.net>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-acpi@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: lm-sensors@lm-sensors.org
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The exynos thermal driver use the of_thermal_*() API to parse the basic data
for thermal management from devicetree file. So, if CONFIG_EXYNOS_THERMAL is
selected without CONFIG_THERMAL_OF, kernel can build it without any problem.
But, exynos thermal driver is not working with following error log. This patch
add the dependency of CONFIG_THERMAL_OF instead of CONFIG_OF.
[ 1.458644] get_th_reg: Cannot get trip points from of-thermal.c!
[ 1.459096] get_th_reg: Cannot get trip points from of-thermal.c!
[ 1.465211] exynos4412_tmu_initialize: No CRITICAL trip point defined at of-thermal.c!
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
During probe the regulator (if present) was enabled but not disabled in
case of failure. So an unsuccessful probe lead to enabling the
regulator which was actually not needed because the device was not
enabled.
Additionally each deferred probe lead to increase of regulator enable
count so it would not be effectively disabled during removal of the
device.
Test HW: Exynos4412 - Trats2 board
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 498d22f616 ("thermal: exynos: Support for TMU regulator defined at device tree")
Cc: <stable@vger.kernel.org>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch adds the support for Exynos5433's TMU (Thermal Management Unit).
Exynos5433 has a little different register bit fields as following description:
- Support the eight trip points for rising/falling interrupt by using two registers
- Read the calibration type (1-point or 2-point) and sensor id from TRIMINFO register
- Use a little different register address
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch fixes the wrong control of PD_DET_EN (power down detection mode)
for Exynos7 because exynos7_tmu_control() always enables the power down detection
mode regardless 'on' parameter.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
The exynos_tmu_data() function should on entrance test not only for valid
data pointer, but also for data->tmu_read one.
It is important, since afterwards it is dereferenced to get temperature code.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
