Enable Westmere support on SGI UV. The UV initialization code is dependent on
the APICID bits. Westmere-EX uses different APIC bit mapping than Nehalem-EX.
This code reads the apic shift value from a UV MMR to do the proper bit
decoding to determint the pnode.
Signed-off-by: Russ Anderson <rja@sgi.com>
LKML-Reference: <20101026212728.GB15071@sgi.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Avoid 'constant_test_bit()' misoptimization due to cast to non-volatile
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/amd-iommu: Fix rounding-bug in __unmap_single
x86/amd-iommu: Work around S3 BIOS bug
x86/amd-iommu: Set iommu configuration flags in enable-loop
x86, setup: Fix earlyprintk=serial,0x3f8,115200
x86, setup: Fix earlyprintk=serial,ttyS0,115200
While debugging bit_spin_lock() hang, it was tracked down to gcc-4.4
misoptimization of non-inlined constant_test_bit() due to non-volatile
addr when 'const volatile unsigned long *addr' cast to 'unsigned long *'
with subsequent unconditional jump to pause (and not to the test) leading
to hang.
Compiling with gcc-4.3 or disabling CONFIG_OPTIMIZE_INLINING yields inlined
constant_test_bit() and correct jump, thus working around the kernel bug.
Other arches than asm-x86 may implement this slightly differently;
2.6.29 mitigates the misoptimization by changing the function prototype
(commit c4295fbb60) but probably fixing the issue
itself is better.
Signed-off-by: Alexander Chumachenko <ledest@gmail.com>
Signed-off-by: Michael Shigorin <mike@osdn.org.ua>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Using cpuid_eax() to determine feature availability on other than
the current CPU is invalid. And feature availability should also be
checked in the hotplug code path.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch adds a workaround for an IOMMU BIOS problem to
the AMD IOMMU driver. The result of the bug is that the
IOMMU does not execute commands anymore when the system
comes out of the S3 state resulting in system failure. The
bug in the BIOS is that is does not restore certain hardware
specific registers correctly. This workaround reads out the
contents of these registers at boot time and restores them
on resume from S3. The workaround is limited to the specific
IOMMU chipset where this problem occurs.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch moves the setting of the configuration and
feature flags out out the acpi table parsing path and moves
it into the iommu-enable path. This is needed to reliably
fix resume-from-s3.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: hpet: Work around hardware stupidity
x86, build: Disable -fPIE when compiling with CONFIG_CC_STACKPROTECTOR=y
x86, cpufeature: Suppress compiler warning with gcc 3.x
x86, UV: Fix initialization of max_pnode
Lengths and types of breakpoints are encoded in a half byte
into CPU registers. However when we extract these values
and store them, we add a high half byte part to them: 0x40 to the
length and 0x80 to the type.
When that gets reloaded to the CPU registers, the high part
is masked.
While making the instruction breakpoints available for perf,
I zapped that high part on instruction breakpoint encoding
and that broke the arch -> generic translation used by ptrace
instruction breakpoints. Writing dr7 to set an inst breakpoint
was then failing.
There is no apparent reason for these high parts so we could get
rid of them altogether. That's an invasive change though so let's
do that later and for now fix the problem by restoring that inst
breakpoint high part encoding in this sole patch.
Reported-by: Kelvie Wong <kelvie@ieee.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Cc: Will Deacon <will.deacon@arm.com>
compat_alloc_user_space() expects the caller to independently call
access_ok() to verify the returned area. A missing call could
introduce problems on some architectures.
This patch incorporates the access_ok() check into
compat_alloc_user_space() and also adds a sanity check on the length.
The existing compat_alloc_user_space() implementations are renamed
arch_compat_alloc_user_space() and are used as part of the
implementation of the new global function.
This patch assumes NULL will cause __get_user()/__put_user() to either
fail or access userspace on all architectures. This should be
followed by checking the return value of compat_access_user_space()
for NULL in the callers, at which time the access_ok() in the callers
can also be removed.
Reported-by: Ben Hawkes <hawkes@sota.gen.nz>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: James Bottomley <jejb@parisc-linux.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: <stable@kernel.org>
This more or less reverts commits 08be979 (x86: Force HPET
readback_cmp for all ATI chipsets) and 30a564be (x86, hpet: Restrict
read back to affected ATI chipsets) to the status of commit 8da854c
(x86, hpet: Erratum workaround for read after write of HPET
comparator).
The delta to commit 8da854c is mostly comments and the change from
WARN_ONCE to printk_once as we know the call path of this function
already.
This needs really in depth explanation:
First of all the HPET design is a complete failure. Having a counter
compare register which generates an interrupt on matching values
forces the software to do at least one superfluous readback of the
counter register.
While it is nice in theory to program "absolute" time events it is
practically useless because the timer runs at some absurd frequency
which can never be matched to real world units. So we are forced to
calculate a relative delta and this forces a readout of the actual
counter value, adding the delta and programming the compare
register. When the delta is small enough we run into the danger that
we program a compare value which is already in the past. Due to the
compare for equal nature of HPET we need to read back the counter
value after writing the compare rehgister (btw. this is necessary for
absolute timeouts as well) to make sure that we did not miss the timer
event. We try to work around that by setting the minimum delta to a
value which is larger than the theoretical time which elapses between
the counter readout and the compare register write, but that's only
true in theory. A NMI or SMI which hits between the readout and the
write can easily push us beyond that limit. This would result in
waiting for the next HPET timer interrupt until the 32bit wraparound
of the counter happens which takes about 306 seconds.
So we designed the next event function to look like:
match = read_cnt() + delta;
write_compare_ref(match);
return read_cnt() < match ? 0 : -ETIME;
At some point we got into trouble with certain ATI chipsets. Even the
above "safe" procedure failed. The reason was that the write to the
compare register was delayed probably for performance reasons. The
theory was that they wanted to avoid the synchronization of the write
with the HPET clock, which is understandable. So the write does not
hit the compare register directly instead it goes to some intermediate
register which is copied to the real compare register in sync with the
HPET clock. That opens another window for hitting the dreaded "wait
for a wraparound" problem.
To work around that "optimization" we added a read back of the compare
register which either enforced the update of the just written value or
just delayed the readout of the counter enough to avoid the issue. We
unfortunately never got any affirmative info from ATI/AMD about this.
One thing is sure, that we nuked the performance "optimization" that
way completely and I'm pretty sure that the result is worse than
before some HW folks came up with those.
Just for paranoia reasons I added a check whether the read back
compare register value was the same as the value we wrote right
before. That paranoia check triggered a couple of years after it was
added on an Intel ICH9 chipset. Venki added a workaround (commit
8da854c) which was reading the compare register twice when the first
check failed. We considered this to be a penalty in general and
restricted the readback (thus the wasted CPU cycles) to the known to
be affected ATI chipsets.
This turned out to be a utterly wrong decision. 2.6.35 testers
experienced massive problems and finally one of them bisected it down
to commit 30a564be which spured some further investigation.
Finally we got confirmation that the write to the compare register can
be delayed by up to two HPET clock cycles which explains the problems
nicely. All we can do about this is to go back to Venki's initial
workaround in a slightly modified version.
Just for the record I need to say, that all of this could have been
avoided if hardware designers and of course the HPET committee would
have thought about the consequences for a split second. It's out of my
comprehension why designing a working timer is so hard. There are two
ways to achieve it:
1) Use a counter wrap around aware compare_reg <= counter_reg
implementation instead of the easy compare_reg == counter_reg
Downsides:
- It needs more silicon.
- It needs a readout of the counter to apply a relative
timeout. This is necessary as the counter does not run in
any useful (and adjustable) frequency and there is no
guarantee that the counter which is used for timer events is
the same which is used for reading the actual time (and
therefor for calculating the delta)
Upsides:
- None
2) Use a simple down counter for relative timer events
Downsides:
- Absolute timeouts are not possible, which is not a problem
at all in the context of an OS and the expected
max. latencies/jitter (also see Downsides of #1)
Upsides:
- It needs less or equal silicon.
- It works ALWAYS
- It is way faster than a compare register based solution (One
write versus one write plus at least one and up to four
reads)
I would not be so grumpy about all of this, if I would not have been
ignored for many years when pointing out these flaws to various
hardware folks. I really hate timers (at least those which seem to be
designed by janitors).
Though finally we got a reasonable explanation plus a solution and I
want to thank all the folks involved in chasing it down and providing
valuable input to this.
Bisected-by: Nix <nix@esperi.org.uk>
Reported-by: Artur Skawina <art.08.09@gmail.com>
Reported-by: Damien Wyart <damien.wyart@free.fr>
Reported-by: John Drescher <drescherjm@gmail.com>
Cc: Venkatesh Pallipadi <venki@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: stable@kernel.org
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Gcc 3.x generates a warning
arch/x86/include/asm/cpufeature.h: In function `__static_cpu_has':
arch/x86/include/asm/cpufeature.h:326: warning: asm operand 1 probably doesn't match constraints
on each file.
But static_cpu_has() for gcc 3.x does not need __static_cpu_has().
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
LKML-Reference: <201008300127.o7U1RC6Z044051@www262.sakura.ne.jp>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'kvm-updates/2.6.36' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Perform hardware_enable in CPU_STARTING callback
KVM: i8259: fix migration
KVM: fix i8259 oops when no vcpus are online
KVM: x86 emulator: fix regression with cmpxchg8b on i386 hosts
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, mcheck: Avoid duplicate sysfs links/files for thresholding banks
io-mapping: Fix the address space annotations
x86: Fix the address space annotations of iomap_atomic_prot_pfn()
x86, mm: Fix CONFIG_VMSPLIT_1G and 2G_OPT trampoline
x86, hwmon: Fix unsafe smp_processor_id() in thermal_throttle_add_dev
operand::val and operand::orig_val are 32-bit on i386, whereas cmpxchg8b
operands are 64-bit.
Fix by adding val64 and orig_val64 union members to struct operand, and
using them where needed.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: bus speed strings should be const
PCI hotplug: Fix build with CONFIG_ACPI unset
PCI: PCIe: Remove the port driver module exit routine
PCI: PCIe: Move PCIe PME code to the pcie directory
PCI: PCIe: Disable PCIe port services during port initialization
PCI: PCIe: Ask BIOS for control of all native services at once
ACPI/PCI: Negotiate _OSC control bits before requesting them
ACPI/PCI: Do not preserve _OSC control bits returned by a query
ACPI/PCI: Make acpi_pci_query_osc() return control bits
ACPI/PCI: Reorder checks in acpi_pci_osc_control_set()
PCI: PCIe: Introduce commad line switch for disabling port services
PCI: PCIe AER: Introduce pci_aer_available()
x86/PCI: only define pci_domain_nr if PCI and PCI_DOMAINS are set
PCI: provide stub pci_domain_nr function for !CONFIG_PCI configs
This patch fixes the sparse warnings when the return pointer of
iomap_atomic_prot_pfn() is used as an argument of iowrite32()
and friends.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
LKML-Reference: <1283633804-11749-1-git-send-email-currojerez@riseup.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, tsc, sched: Recompute cyc2ns_offset's during resume from sleep states
sched: Fix rq->clock synchronization when migrating tasks
TSC's get reset after suspend/resume (even on cpu's with invariant TSC
which runs at a constant rate across ACPI P-, C- and T-states). And in
some systems BIOS seem to reinit TSC to arbitrary large value (still
sync'd across cpu's) during resume.
This leads to a scenario of scheduler rq->clock (sched_clock_cpu()) less
than rq->age_stamp (introduced in 2.6.32). This leads to a big value
returned by scale_rt_power() and the resulting big group power set by the
update_group_power() is causing improper load balancing between busy and
idle cpu's after suspend/resume.
This resulted in multi-threaded workloads (like kernel-compilation) go
slower after suspend/resume cycle on core i5 laptops.
Fix this by recomputing cyc2ns_offset's during resume, so that
sched_clock() continues from the point where it was left off during
suspend.
Reported-by: Florian Pritz <flo@xssn.at>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: <stable@kernel.org> # [v2.6.32+]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1282262618.2675.24.camel@sbsiddha-MOBL3.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix dummy inline stubs for trampoline-related functions when no
trampolines exist (until we get rid of the no-trampoline case
entirely.)
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <4C6C294D.3030404@zytor.com>
This patch fixes machine crashes which occur when heavily exercising the
CPU hotplug codepaths on a 32-bit kernel. These crashes are caused by
AMD Erratum 383 and result in a fatal machine check exception. Here's
the scenario:
1. On 32-bit, the swapper_pg_dir page table is used as the initial page
table for booting a secondary CPU.
2. To make this work, swapper_pg_dir needs a direct mapping of physical
memory in it (the low mappings). By adding those low, large page (2M)
mappings (PAE kernel), we create the necessary conditions for Erratum
383 to occur.
3. Other CPUs which do not participate in the off- and onlining game may
use swapper_pg_dir while the low mappings are present (when leave_mm is
called). For all steps below, the CPU referred to is a CPU that is using
swapper_pg_dir, and not the CPU which is being onlined.
4. The presence of the low mappings in swapper_pg_dir can result
in TLB entries for addresses below __PAGE_OFFSET to be established
speculatively. These TLB entries are marked global and large.
5. When the CPU with such TLB entry switches to another page table, this
TLB entry remains because it is global.
6. The process then generates an access to an address covered by the
above TLB entry but there is a permission mismatch - the TLB entry
covers a large global page not accessible to userspace.
7. Due to this permission mismatch a new 4kb, user TLB entry gets
established. Further, Erratum 383 provides for a small window of time
where both TLB entries are present. This results in an uncorrectable
machine check exception signalling a TLB multimatch which panics the
machine.
There are two ways to fix this issue:
1. Always do a global TLB flush when a new cr3 is loaded and the
old page table was swapper_pg_dir. I consider this a hack hard
to understand and with performance implications
2. Do not use swapper_pg_dir to boot secondary CPUs like 64-bit
does.
This patch implements solution 2. It introduces a trampoline_pg_dir
which has the same layout as swapper_pg_dir with low_mappings. This page
table is used as the initial page table of the booting CPU. Later in the
bringup process, it switches to swapper_pg_dir and does a global TLB
flush. This fixes the crashes in our test cases.
-v2: switch to swapper_pg_dir right after entering start_secondary() so
that we are able to access percpu data which might not be mapped in the
trampoline page table.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
LKML-Reference: <20100816123833.GB28147@aftab>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Make do_execve() take a const filename pointer so that kernel_execve() compiles
correctly on ARM:
arch/arm/kernel/sys_arm.c:88: warning: passing argument 1 of 'do_execve' discards qualifiers from pointer target type
This also requires the argv and envp arguments to be consted twice, once for
the pointer array and once for the strings the array points to. This is
because do_execve() passes a pointer to the filename (now const) to
copy_strings_kernel(). A simpler alternative would be to cast the filename
pointer in do_execve() when it's passed to copy_strings_kernel().
do_execve() may not change any of the strings it is passed as part of the argv
or envp lists as they are some of them in .rodata, so marking these strings as
const should be fine.
Further kernel_execve() and sys_execve() need to be changed to match.
This has been test built on x86_64, frv, arm and mips.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Otherwise we'll duplicate definitions with the pci.h stubs.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Mark arguments to certain system calls as being const where they should be but
aren't. The list includes:
(*) The filename arguments of various stat syscalls, execve(), various utimes
syscalls and some mount syscalls.
(*) The filename arguments of some syscall helpers relating to the above.
(*) The buffer argument of various write syscalls.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, UV: Initialize BAU MMRs only on hubs with cpus
x86, UV: Modularize BAU send and wait
x86, UV: BAU broadcast to the local hub
x86, UV: Correct BAU regular message type
x86, UV: Remove BAU check for stay-busy
x86, UV: Correct BAU discovery of hubs and sockets
x86, UV: Correct BAU software acknowledge
x86, UV: BAU structure rearranging
x86, UV: Shorten access to BAU statistics structure
x86, UV: Disable BAU on network congestion
x86, UV: BAU tunables into a debugfs file
x86, UV: Calculate BAU destination timeout
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, asm: Use a lower case name for the end macro in atomic64_386_32.S
x86, asm: Refactor atomic64_386_32.S to support old binutils and be cleaner
x86: Document __phys_reloc_hide() usage in __pa_symbol()
x86, apic: Map the local apic when parsing the MP table.
This replaces Version 1 of this patch, which broke the build when
CONFIG_KEXEC and CONFIG_CRASH_DUMP were configured off. In that case
the storage for the 'in_crash_kexec' flag was never built.
This version defines that flag as 0 if CONFIG_KEXEC is not set.
The patch is tested with all combinations of those two options.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <E1OiZcw-0001Hb-2g@eag09.americas.sgi.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'stable/xen-swiotlb-0.8.6' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
x86: Detect whether we should use Xen SWIOTLB.
pci-swiotlb-xen: Add glue code to setup dma_ops utilizing xen_swiotlb_* functions.
swiotlb-xen: SWIOTLB library for Xen PV guest with PCI passthrough.
xen/mmu: inhibit vmap aliases rather than trying to clear them out
vmap: add flag to allow lazy unmap to be disabled at runtime
xen: Add xen_create_contiguous_region
xen: Rename the balloon lock
xen: Allow unprivileged Xen domains to create iomap pages
xen: use _PAGE_IOMAP in ioremap to do machine mappings
Fix up trivial conflicts (adding both xen swiotlb and xen pci platform
driver setup close to each other) in drivers/xen/{Kconfig,Makefile} and
include/xen/xen-ops.h
Architectures implement dma_is_consistent() in different ways (some
misinterpret the definition of API in DMA-API.txt). So it hasn't been so
useful for drivers. We have only one user of the API in tree. Unlikely
out-of-tree drivers use the API.
Even if we fix dma_is_consistent() in some architectures, it doesn't look
useful at all. It was invented long ago for some old systems that can't
allocate coherent memory at all. It's better to export only APIs that are
definitely necessary for drivers.
Let's remove this API.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dma_get_cache_alignment returns the minimum DMA alignment. Architectures
defines it as ARCH_DMA_MINALIGN (formally ARCH_KMALLOC_MINALIGN). So we
can unify dma_get_cache_alignment implementations.
Note that some architectures implement dma_get_cache_alignment wrongly.
dma_get_cache_alignment() should return the minimum DMA alignment. So
fully-coherent architectures should return 1. This patch also fixes this
issue.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Until all supported versions of gcc recognize
-fno-strict-overflow, we should keep the RELOC_HIDE() magic in
__pa_symbol(). Comment it.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
LKML-Reference: <1281508661-29507-1-git-send-email-namhyung@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block: (149 commits)
block: make sure that REQ_* types are seen even with CONFIG_BLOCK=n
xen-blkfront: fix missing out label
blkdev: fix blkdev_issue_zeroout return value
block: update request stacking methods to support discards
block: fix missing export of blk_types.h
writeback: fix bad _bh spinlock nesting
drbd: revert "delay probes", feature is being re-implemented differently
drbd: Initialize all members of sync_conf to their defaults [Bugz 315]
drbd: Disable delay probes for the upcomming release
writeback: cleanup bdi_register
writeback: add new tracepoints
writeback: remove unnecessary init_timer call
writeback: optimize periodic bdi thread wakeups
writeback: prevent unnecessary bdi threads wakeups
writeback: move bdi threads exiting logic to the forker thread
writeback: restructure bdi forker loop a little
writeback: move last_active to bdi
writeback: do not remove bdi from bdi_list
writeback: simplify bdi code a little
writeback: do not lose wake-ups in bdi threads
...
Fixed up pretty trivial conflicts in drivers/block/virtio_blk.c and
drivers/scsi/scsi_error.c as per Jens.
* 'writable_limits' of git://decibel.fi.muni.cz/~xslaby/linux:
unistd: add __NR_prlimit64 syscall numbers
rlimits: implement prlimit64 syscall
rlimits: switch more rlimit syscalls to do_prlimit
rlimits: redo do_setrlimit to more generic do_prlimit
rlimits: add rlimit64 structure
rlimits: do security check under task_lock
rlimits: allow setrlimit to non-current tasks
rlimits: split sys_setrlimit
rlimits: selinux, do rlimits changes under task_lock
rlimits: make sure ->rlim_max never grows in sys_setrlimit
rlimits: add task_struct to update_rlimit_cpu
rlimits: security, add task_struct to setrlimit
Fix up various system call number conflicts. We not only added fanotify
system calls in the meantime, but asm-generic/unistd.h added a wait4
along with a range of reserved per-architecture system calls.
* 'for-linus' of git://git.infradead.org/users/eparis/notify: (132 commits)
fanotify: use both marks when possible
fsnotify: pass both the vfsmount mark and inode mark
fsnotify: walk the inode and vfsmount lists simultaneously
fsnotify: rework ignored mark flushing
fsnotify: remove global fsnotify groups lists
fsnotify: remove group->mask
fsnotify: remove the global masks
fsnotify: cleanup should_send_event
fanotify: use the mark in handler functions
audit: use the mark in handler functions
dnotify: use the mark in handler functions
inotify: use the mark in handler functions
fsnotify: send fsnotify_mark to groups in event handling functions
fsnotify: Exchange list heads instead of moving elements
fsnotify: srcu to protect read side of inode and vfsmount locks
fsnotify: use an explicit flag to indicate fsnotify_destroy_mark has been called
fsnotify: use _rcu functions for mark list traversal
fsnotify: place marks on object in order of group memory address
vfs/fsnotify: fsnotify_close can delay the final work in fput
fsnotify: store struct file not struct path
...
Fix up trivial delete/modify conflict in fs/notify/inotify/inotify.c.
No real bugs, just some dead code and some fixups.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kunmap_atomic() is currently at level -4 on Rusty's "Hard To Misuse"
list[1] ("Follow common convention and you'll get it wrong"), except in
some architectures when CONFIG_DEBUG_HIGHMEM is set[2][3].
kunmap() takes a pointer to a struct page; kunmap_atomic(), however, takes
takes a pointer to within the page itself. This seems to once in a while
trip people up (the convention they are following is the one from
kunmap()).
Make it much harder to misuse, by moving it to level 9 on Rusty's list[4]
("The compiler/linker won't let you get it wrong"). This is done by
refusing to build if the type of its first argument is a pointer to a
struct page.
The real kunmap_atomic() is renamed to kunmap_atomic_notypecheck()
(which is what you would call in case for some strange reason calling it
with a pointer to a struct page is not incorrect in your code).
The previous version of this patch was compile tested on x86-64.
[1] http://ozlabs.org/~rusty/index.cgi/tech/2008-04-01.html
[2] In these cases, it is at level 5, "Do it right or it will always
break at runtime."
[3] At least mips and powerpc look very similar, and sparc also seems to
share a common ancestor with both; there seems to be quite some
degree of copy-and-paste coding here. The include/asm/highmem.h file
for these three archs mention x86 CPUs at its top.
[4] http://ozlabs.org/~rusty/index.cgi/tech/2008-03-30.html
[5] As an aside, could someone tell me why mn10300 uses unsigned long as
the first parameter of kunmap_atomic() instead of void *?
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Cc: Russell King <linux@arm.linux.org.uk> (arch/arm)
Cc: Ralf Baechle <ralf@linux-mips.org> (arch/mips)
Cc: David Howells <dhowells@redhat.com> (arch/frv, arch/mn10300)
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com> (arch/mn10300)
Cc: Kyle McMartin <kyle@mcmartin.ca> (arch/parisc)
Cc: Helge Deller <deller@gmx.de> (arch/parisc)
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org> (arch/parisc)
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> (arch/powerpc)
Cc: Paul Mackerras <paulus@samba.org> (arch/powerpc)
Cc: "David S. Miller" <davem@davemloft.net> (arch/sparc)
Cc: Thomas Gleixner <tglx@linutronix.de> (arch/x86)
Cc: Ingo Molnar <mingo@redhat.com> (arch/x86)
Cc: "H. Peter Anvin" <hpa@zytor.com> (arch/x86)
Cc: Arnd Bergmann <arnd@arndb.de> (include/asm-generic)
Cc: Rusty Russell <rusty@rustcorp.com.au> ("Hard To Misuse" list)
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-xsave-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, xsave: Make xstate_enable_boot_cpu() __init, protect on CPU 0
x86, xsave: Add __init attribute to setup_xstate_features()
x86, xsave: Make init_xstate_buf static
x86, xsave: Check cpuid level for XSTATE_CPUID (0x0d)
x86, xsave: Introduce xstate enable functions
x86, xsave: Separate fpu and xsave initialization
x86, xsave: Move boot cpu initialization to xsave_init()
x86, xsave: 32/64 bit boot cpu check unification in initialization
x86, xsave: Do not include asm/i387.h in asm/xsave.h
x86, xsave: Use xsaveopt in context-switch path when supported
x86, xsave: Sync xsave memory layout with its header for user handling
x86, xsave: Track the offset, size of state in the xsave layout
* 'x86-olpc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, olpc: Constify an olpc_ofw() arg
x86, olpc: Use pr_debug() for EC commands
x86, olpc: Add comment about implicit optimization barrier
x86, olpc: Add support for calling into OpenFirmware
* 'x86-alternatives-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, alternatives: BUG on encountering an invalid CPU feature number
x86, alternatives: Fix one more open-coded 8-bit alternative number
x86, alternatives: Use 16-bit numbers for cpufeature index
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Clean up arch/x86/kernel/cpu/mtrr/cleanup.c: use ";" not "," to terminate statements
* 'x86-vmware-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, vmware: Preset lpj values when on VMware.
* 'x86-mtrr-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, mtrr: Use stop machine context to rendezvous all the cpu's
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/apic/es7000_32: Remove unused variable
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Avoid unnecessary __clear_user() and xrstor in signal handling
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, vdso: Unmap vdso pages
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (30 commits)
PCI: update for owner removal from struct device_attribute
PCI: Fix warnings when CONFIG_DMI unset
PCI: Do not run NVidia quirks related to MSI with MSI disabled
x86/PCI: use for_each_pci_dev()
PCI: use for_each_pci_dev()
PCI: MSI: Restore read_msi_msg_desc(); add get_cached_msi_msg_desc()
PCI: export SMBIOS provided firmware instance and label to sysfs
PCI: Allow read/write access to sysfs I/O port resources
x86/PCI: use host bridge _CRS info on ASRock ALiveSATA2-GLAN
PCI: remove unused HAVE_ARCH_PCI_SET_DMA_MAX_SEGMENT_{SIZE|BOUNDARY}
PCI: disable mmio during bar sizing
PCI: MSI: Remove unsafe and unnecessary hardware access
PCI: Default PCIe ASPM control to on and require !EMBEDDED to disable
PCI: kernel oops on access to pci proc file while hot-removal
PCI: pci-sysfs: remove casts from void*
ACPI: Disable ASPM if the platform won't provide _OSC control for PCIe
PCI hotplug: make sure child bridges are enabled at hotplug time
PCI hotplug: shpchp: Removed check for hotplug of display devices
PCI hotplug: pciehp: Fixed return value sign for pciehp_unconfigure_device
PCI: Don't enable aspm before drivers have had a chance to veto it
...
* 'x86-rwsem-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, rwsem: Minor cleanups
x86, rwsem: Stay on fast path when count > 0 in __up_write()
* 'x86-gcc46-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, gcc-4.6: Fix set but not read variables
x86, gcc-4.6: Avoid unused by set variables in rdmsr
