Impact: fix bootup crash
Even though it tested fine for me, there was still a bug in the
first patch: I have overlooked a call to ptregscall_common. This
patch fixes that, I think, but the code is never executed for
me while running a debian install... (I tested this by putting
an "1:jmp 1b" in there.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
DISABLE_INTERRUPTS(CLBR_NONE)/TRACE_IRQS_OFF is now always
executed just before paranoid_exit. Move it there.
Split out paranoidzeroentry, paranoiderrorentry, and
paranoidzeroentry_ist to get more readable macro's.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, shrink kernel image size
Also expand the paranoid_exit0 macro into nmi_exit inside the
nmi stub in the case of enabled irq-tracing.
This gives a few hundred bytes code size reduction.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
The save_rest function completes a partial stack frame for use
by the PTREGSCALL macro. This also avoids the indirect call in
PTREGSCALLs.
This adds the macro movq_cfi_restore to hide the CFI_RESTORE
annotation when restoring a register from the stack frame.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: build fix
The break builds with older binutils (2.16.1):
arch/x86/kernel/entry_64.S: Assembler messages:
arch/x86/kernel/entry_64.S:282: Error: too many positional arguments
arch/x86/kernel/entry_64.S:283: Error: too many positional arguments
arch/x86/kernel/entry_64.S:284: Error: too many positional arguments
arch/x86/kernel/entry_64.S:285: Error: too many positional arguments
arch/x86/kernel/entry_64.S:286: Error: too many positional arguments
arch/x86/kernel/entry_64.S:287: Error: too many positional arguments
arch/x86/kernel/entry_64.S:288: Error: too many positional arguments
arch/x86/kernel/entry_64.S:289: Error: too many positional arguments
arch/x86/kernel/entry_64.S:290: Error: too many positional arguments
Took some time to figure out the detail that GAS chokes on: it's
negative offsets. Rearrange the calculations to make sure we never
go negative.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This add-on patch to x86: move entry_64.S register saving out
of the macros visually cleans up the appearance of the code by
introducing some basic helper macro's. It also adds some cfi
annotations which were missing.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Here is a combined patch that moves "save_args" out-of-line for
the interrupt macro and moves "error_entry" mostly out-of-line
for the zeroentry and errorentry macros.
The save_args function becomes really straightforward and easy
to understand, with the possible exception of the stack switch
code, which now needs to copy the return address of to the
calling function. Normal interrupts arrive with ((~vector)-0x80)
on the stack, which gets adjusted in common_interrupt:
<common_interrupt>:
(5) addq $0xffffffffffffff80,(%rsp) /* -> ~(vector) */
(4) sub $0x50,%rsp /* space for registers */
(5) callq ffffffff80211290 <save_args>
(5) callq ffffffff80214290 <do_IRQ>
<ret_from_intr>:
...
An apic interrupt stub now look like this:
<thermal_interrupt>:
(5) pushq $0xffffffffffffff05 /* ~(vector) */
(4) sub $0x50,%rsp /* space for registers */
(5) callq ffffffff80211290 <save_args>
(5) callq ffffffff80212b8f <smp_thermal_interrupt>
(5) jmpq ffffffff80211f93 <ret_from_intr>
Similarly the exception handler register saving function becomes
simpler, without the need of any parameter shuffling. The stub
for an exception without errorcode looks like this:
<overflow>:
(6) callq *0x1cad12(%rip) # ffffffff803dd448 <pv_irq_ops+0x38>
(2) pushq $0xffffffffffffffff /* no syscall */
(4) sub $0x78,%rsp /* space for registers */
(5) callq ffffffff8030e3b0 <error_entry>
(3) mov %rsp,%rdi /* pt_regs pointer */
(2) xor %esi,%esi /* no error code */
(5) callq ffffffff80213446 <do_overflow>
(5) jmpq ffffffff8030e460 <error_exit>
And one for an exception with errorcode like this:
<segment_not_present>:
(6) callq *0x1cab92(%rip) # ffffffff803dd448 <pv_irq_ops+0x38>
(4) sub $0x78,%rsp /* space for registers */
(5) callq ffffffff8030e3b0 <error_entry>
(3) mov %rsp,%rdi /* pt_regs pointer */
(5) mov 0x78(%rsp),%rsi /* load error code */
(9) movq $0xffffffffffffffff,0x78(%rsp) /* no syscall */
(5) callq ffffffff80213209 <do_segment_not_present>
(5) jmpq ffffffff8030e460 <error_exit>
Unfortunately, this last type is more than 32 bytes. But the total space
savings due to this patch is about 2500 bytes on an smp-configuration,
and I think the code is clearer than it was before. The tested kernels
were non-paravirt ones (i.e., without the indirect call at the top of
the exception handlers).
Anyhow, I tested this patch on top of a recent -tip. The machine
was an 2x4-core Xeon at 2333MHz. Measured where the delays between
(almost-)adjacent rdtsc instructions. The graphs show how much
time is spent outside of the program as a function of the measured
delay. The area under the graph represents the total time spent
outside the program. Eight instances of the rdtsctest were
started, each pinned to a single cpu. The histogams are added.
For each kernel two measurements were done: one in mostly idle
condition, the other while running "bonnie++ -f", bound to cpu 0.
Each measurement took 40 minutes runtime. See the attached graphs
for the results. The graphs overlap almost everywhere, but there
are small differences.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
this compiler warning:
arch/x86/kernel/ds.c: In function 'ds_request':
arch/x86/kernel/ds.c:368: warning: 'context' may be used uninitialized in this function
Shows that the code flow in ds_request() is buggy - it goes into
the unlock+release-context path even when the context is not allocated
yet.
First allocate the context, then do the other checks.
Also, take care with GFP allocations under the ds_lock spinlock.
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix incorrectly marked unstable TSC clock
Patch (commit 0d12cdd "sched: improve sched_clock() performance") has
a regression on one of the test systems here.
With the patch, I see:
checking TSC synchronization [CPU#0 -> CPU#1]:
Measured 28 cycles TSC warp between CPUs, turning off TSC clock.
Marking TSC unstable due to check_tsc_sync_source failed
Whereas, without the patch syncs pass fine on all CPUs:
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Due to this, TSC is marked unstable, when it is not actually unstable.
This is because syncs in check_tsc_wrap() goes away due to this commit.
As per the discussion on this thread, correct way to fix this is to add
explicit syncs as below?
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
All blame goes to: color white,red "[^[:graph:]]+$"
in .nanorc ;).
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix es7000 build
CC arch/x86/kernel/es7000_32.o
arch/x86/kernel/es7000_32.c: In function find_unisys_acpi_oem_table:
arch/x86/kernel/es7000_32.c:255: error: implicit declaration of function acpi_get_table_with_size
arch/x86/kernel/es7000_32.c:261: error: implicit declaration of function early_acpi_os_unmap_memory
arch/x86/kernel/es7000_32.c: In function unmap_unisys_acpi_oem_table:
arch/x86/kernel/es7000_32.c:277: error: implicit declaration of function __acpi_unmap_table
make[1]: *** [arch/x86/kernel/es7000_32.o] Error 1
we applied one patch out of order...
| commit a73aaedd95
| Author: Yinghai Lu <yhlu.kernel@gmail.com>
| Date: Sun Sep 14 02:33:14 2008 -0700
|
| x86: check dsdt before find oem table for es7000, v2
|
| v2: use __acpi_unmap_table()
that patch need:
x86: use early_ioremap in __acpi_map_table
x86: always explicitly map acpi memory
acpi: remove final __acpi_map_table mapping before setting acpi_gbl_permanent_mmap
acpi/x86: introduce __apci_map_table, v4
submitted to the ACPI tree but not upstream yet.
fix it until those patches applied, need to revert this one
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix a problem where ds_request() returned an error without releasing the
ds lock.
Reported-by: Stephane Eranian <eranian@gmail.com>
Signed-off-by: Markus Metzger <markus.t.metzger@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit e51af66308, which was
wrongly hoovered up and submitted about a month after a better fix had
already been merged.
The better fix is commit cbda1ba898
("PCI/iommu: blacklist DMAR on Intel G31/G33 chipsets"), where we do
this blacklisting based on the DMI identification for the offending
motherboard, since sometimes this chipset (or at least a chipset with
the same PCI ID) apparently _does_ actually have an IOMMU.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: Fix interrupt via the apicinterrupt macro
Checkin 939b787130 changed the
"interrupt" macro, but the "interrupt" macro is also invoked
indirectly from the "apicinterrupt" macro.
The "apicinterrupt" macro probably should have its own collection of
systematic stubs for the same reason the main IRQ code does; as is it
is a huge amount of replicated code.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'kvm-updates/2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: Fix pit memory leak if unable to allocate irq source id
KVM: ia64: fix vmm_spin_{un}lock for !CONFIG_SMP
KVM: VMX: Set IGMT bit in EPT entry
KVM: Require the PCI subsystem
x86: KVM guest: fix section mismatch warning in kvmclock.c
KVM: ia64: Use guest signal mask when blocking
KVM: MMU: increase per-vcpu rmap cache alloc size
Older versions of gas don't implement the C-style != operator, they
instead want the Pascal-style <> operator. Change != to <> so we
don't break compilation with those old versions of gas.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (47 commits)
ACPI: pci_link: remove acpi_irq_balance_set() interface
fujitsu-laptop: Add DMI callback for Lifebook S6420
ACPI: EC: Don't do transaction from GPE handler in poll mode.
ACPI: EC: lower interrupt storm treshold
ACPICA: Use spinlock for acpi_{en|dis}able_gpe
ACPI: EC: restart failed command
ACPI: EC: wait for last write gpe
ACPI: EC: make kernel messages more useful when GPE storm is detected
ACPI: EC: revert msleep patch
thinkpad_acpi: fingers off backlight if video.ko is serving this functionality
sony-laptop: fingers off backlight if video.ko is serving this functionality
msi-laptop: fingers off backlight if video.ko is serving this functionality
fujitsu-laptop: fingers off backlight if video.ko is serving this functionality
eeepc-laptop: fingers off backlight if video.ko is serving this functionality
compal: fingers off backlight if video.ko is serving this functionality
asus-acpi: fingers off backlight if video.ko is serving this functionality
Acer-WMI: fingers off backlight if video.ko is serving this functionality
ACPI video: if no ACPI backlight support, use vendor drivers
ACPI: video: Ignore devices that aren't present in hardware
Delete an unwanted return statement at evgpe.c
...
This removes the acpi_irq_balance_set() interface from the PCI
interrupt link driver.
x86 used acpi_irq_balance_set() to tell the PCI interrupt link
driver to configure links to minimize IRQ sharing. But the link
driver can easily figure out whether to turn on IRQ balancing
based on the IRQ model (PIC/IOAPIC/etc), so we can get rid of
that external interface.
It's better for the driver to figure this out at init-time. If
we set it externally via the x86 code, the interface reduces
modularity, and we depend on the fact that acpi_process_madt()
happens before we process the kernel command line.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Move the IRQ stub generation to assembly to simplify it and for
consistency with 32 bits. Doing it in a C file with asm() statements
doesn't help clarity, and it prevents some optimizations.
Shrink the IRQ stubs down to just over four bytes per (we fit seven
into a 32-byte chunk.) This shrinks the total icache consumption of
the IRQ stubs down to an even kilobyte, if all of them are in active
use.
The downside is that we end up with a double jump, which could have a
negative effect on some pipelines. The double jump is always inside
the same cacheline on any modern chips.
To get the most effect, cache-align the IRQ stubs.
This makes the 64-bit code match changes already done to the 32-bit
code, and should open up irqinit*.c for unification.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Shrink the IRQ stubs on 32 bits down to just over four bytes per (we
fit seven into a 32-byte chunk.) This shrinks the total icache
consumption of the IRQ stubs down to an even kilobyte, if all of them
are in active use.
The downside is that we end up with a double jump, which could have a
negative effect on some pipelines. The double jump is always inside
the same cacheline on any modern chips (the exception being
486/Elan/Geode which have only 16-byte cachelines, but are unlikely to
have too many interrupt sources.)
To get the most effect, cache-align the IRQ stubs.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Don't generate interrupt stubs for interrupt vectors below
FIRST_EXTERNAL_VECTOR, and make the table of interrupt vectors
(interrupt[]) __initconst. Both of these changes both conserve memory
and improve consistency with 64 bits.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
WARNING: arch/x86/kernel/built-in.o(.text+0x1722c): Section mismatch
in reference from the function kvm_setup_secondary_clock() to the
function .devinit.text:setup_secondary_APIC_clock()
The function kvm_setup_secondary_clock() references
the function __devinit setup_secondary_APIC_clock().
This is often because kvm_setup_secondary_clock lacks a __devinit
annotation or the annotation of setup_secondary_APIC_clock is wrong.
Signed-off-by: Md.Rakib H. Mullick <rakib.mullick@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
Some functions that may be called from this handler require that
interrupts are disabled. Also, combining IRQF_DISABLED and
IRQF_SHARED does not reliably disable interrupts in a handler, so
remove IRQF_SHARED from the irq flags (this irq is not shared anyway).
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Cc: mingo@elte.hu
Cc: venkatesh.pallipadi@intel.com
Cc: "Will Newton" <will.newton@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In hpet_next_event() we check that the value we just wrote to
HPET_Tn_CMP(timer) has reached the chip. Currently, we're checking that
the value we wrote to HPET_Tn_CMP(timer) is in HPET_T0_CMP, which, if
timer is anything other than timer 0, is likely to fail.
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Cc: mingo@elte.hu
Cc: venkatesh.pallipadi@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It is possible to flood the console with call traces if the WARN_ON
condition is true because of the frequency with which this function is
called.
Signed-off-by: Matt Fleming <mjf@gentoo.org>
Cc: mingo@elte.hu
Cc: venkatesh.pallipadi@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: cleanup
Move rdtsc_barrier() use to vsyscall_64.c where it's relied on,
and point out its role in the context of its use.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
sched_clock() uses cycles_2_ns() needlessly - which is an irq-disabling
variant of __cycles_2_ns().
Most of the time sched_clock() is called with irqs disabled already.
The few places that call it with irqs enabled need to be updated.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit c7ffa6c262.
the assumptio of this change was that this would not break
any existing machine. Andrey Borzenkov reported troubles with
the ACPI reboot method: the system would hang on reboot, necessiating
a power cycle. Probably more systems are affected as well.
Also, there are patches queued up for v2.6.29 to disable virtualization
on emergency_restart() - which was the original motivation of
this change.
Reported-by: Andrey Borzenkov <arvidjaar@mail.ru>
Bisected-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Lazy flushing needs to take care of the unmap path too which is not yet
implemented and leads to stale IO/TLB entries. This is fixed by this
patch.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Impact: fix rare x2apic hang
On x86, x2apic mode accesses for sending IPI's don't have serializing
semantics. If the IPI receivner refers(in lock-free fashion) to some
memory setup by the sender, the need for smp_mb() before sending the
IPI becomes critical in x2apic mode.
Add the smp_mb() in native_flush_tlb_others() before sending the IPI.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix boot hang on 32-bit systems with more than 224 IO-APIC pins
On some 32-bit systems with a lot of IO-APICs probe_nr_irqs() can
return a value larger than NR_IRQS. This will lead to probe_irq_on()
overrunning the irq_desc array.
I hit this when running net-next-2.6 (close to 2.6.28-rc3) on a
Supermicro dual Xeon system. NR_IRQS is 224 but probe_nr_irqs() detects
5 IOAPICs and returns 240. Here are the log messages:
Tue Nov 4 16:53:47 2008 ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
Tue Nov 4 16:53:47 2008 IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
Tue Nov 4 16:53:47 2008 ACPI: IOAPIC (id[0x02] address[0xfec81000] gsi_base[24])
Tue Nov 4 16:53:47 2008 IOAPIC[1]: apic_id 2, version 32, address 0xfec81000, GSI 24-47
Tue Nov 4 16:53:47 2008 ACPI: IOAPIC (id[0x03] address[0xfec81400] gsi_base[48])
Tue Nov 4 16:53:47 2008 IOAPIC[2]: apic_id 3, version 32, address 0xfec81400, GSI 48-71
Tue Nov 4 16:53:47 2008 ACPI: IOAPIC (id[0x04] address[0xfec82000] gsi_base[72])
Tue Nov 4 16:53:47 2008 IOAPIC[3]: apic_id 4, version 32, address 0xfec82000, GSI 72-95
Tue Nov 4 16:53:47 2008 ACPI: IOAPIC (id[0x05] address[0xfec82400] gsi_base[96])
Tue Nov 4 16:53:47 2008 IOAPIC[4]: apic_id 5, version 32, address 0xfec82400, GSI 96-119
Tue Nov 4 16:53:47 2008 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
Tue Nov 4 16:53:47 2008 ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Tue Nov 4 16:53:47 2008 Enabling APIC mode: Flat. Using 5 I/O APICs
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix udelay when "notsc" boot parameter is passed
With notsc passed on commandline, tsc may not be used for
udelays, make sure that we do not use tsc_khz to calculate
the lpj value in such cases.
Reported-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix AMDC1E and XTOPOLOGY conflict in cpufeature
x86: build fix
This makes the late e820 resources use 'insert_resource_expand_to_fit()'
instead of doing a 'reserve_region_with_split()', and also avoids
marking them as IORESOURCE_BUSY.
This results in us being perfectly happy to use pre-existing PCI
resources even if they were marked as being in a reserved region, while
still avoiding any _new_ allocations in the reserved regions. It also
makes for a simpler and more accurate resource tree.
Example resource allocation from Jonathan Corbet, who has firmware that
has an e820 reserved entry that covered a big range (e0000000-fed003ff),
and that had various PCI resources in it set up by firmware.
With old kernels, the reserved range would force us to re-allocate all
pre-existing PCI resources, and his reserved range would end up looking
like this:
e0000000-fed003ff : reserved
fec00000-fec00fff : IOAPIC 0
fed00000-fed003ff : HPET 0
where only the pre-allocated special regions (IOAPIC and HPET) were kept
around.
With 2.6.28-rc2, which uses 'reserve_region_with_split()', Jonathan's
resource tree looked like this:
e0000000-fe7fffff : reserved
fe800000-fe8fffff : PCI Bus 0000:01
fe800000-fe8fffff : reserved
fe900000-fe9d9aff : reserved
fe9d9b00-fe9d9bff : 0000:00:1f.3
fe9d9b00-fe9d9bff : reserved
fe9d9c00-fe9d9fff : 0000:00:1a.7
fe9d9c00-fe9d9fff : reserved
fe9da000-fe9dafff : 0000:00:03.3
fe9da000-fe9dafff : reserved
fe9db000-fe9dbfff : 0000:00:19.0
fe9db000-fe9dbfff : reserved
fe9dc000-fe9dffff : 0000:00:1b.0
fe9dc000-fe9dffff : reserved
fe9e0000-fe9fffff : 0000:00:19.0
fe9e0000-fe9fffff : reserved
fea00000-fea7ffff : 0000:00:02.0
fea00000-fea7ffff : reserved
fea80000-feafffff : 0000:00:02.1
fea80000-feafffff : reserved
feb00000-febfffff : 0000:00:02.0
feb00000-febfffff : reserved
fec00000-fed003ff : reserved
fec00000-fec00fff : IOAPIC 0
fed00000-fed003ff : HPET 0
and because the reserved entry had been split and moved into the
individual resources, and because it used the IORESOURCE_BUSY flag, the
drivers that actually wanted to _use_ those resources couldn't actually
attach to them:
e1000e 0000:00:19.0: BAR 0: can't reserve mem region [0xfe9e0000-0xfe9fffff]
HDA Intel 0000:00:1b.0: BAR 0: can't reserve mem region [0xfe9dc000-0xfe9dffff]
with this patch, the resource tree instead becomes
e0000000-fed003ff : reserved
fe800000-fe8fffff : PCI Bus 0000:01
fe9d9b00-fe9d9bff : 0000:00:1f.3
fe9d9c00-fe9d9fff : 0000:00:1a.7
fe9d9c00-fe9d9fff : ehci_hcd
fe9da000-fe9dafff : 0000:00:03.3
fe9db000-fe9dbfff : 0000:00:19.0
fe9db000-fe9dbfff : e1000e
fe9dc000-fe9dffff : 0000:00:1b.0
fe9dc000-fe9dffff : ICH HD audio
fe9e0000-fe9fffff : 0000:00:19.0
fe9e0000-fe9fffff : e1000e
fea00000-fea7ffff : 0000:00:02.0
fea80000-feafffff : 0000:00:02.1
feb00000-febfffff : 0000:00:02.0
fec00000-fec00fff : IOAPIC 0
fed00000-fed003ff : HPET 0
ie the one reserved region now ends up surrounding all the PCI resources
that were allocated inside of it by firmware, and because it is not
marked BUSY, drivers have no problem attaching to the pre-allocated
resources.
Reported-and-tested-by: Jonathan Corbet <corbet@lwn.net>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: build fix on certain UP configs
fix:
arch/x86/kernel/cpu/common.c: In function 'cpu_init':
arch/x86/kernel/cpu/common.c:1141: error: 'boot_cpu_id' undeclared (first use in this function)
arch/x86/kernel/cpu/common.c:1141: error: (Each undeclared identifier is reported only once
arch/x86/kernel/cpu/common.c:1141: error: for each function it appears in.)
Pull in asm/smp.h on UP, so that we get the definition of
boot_cpu_id.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix:
arch/x86/kernel/cpu/common.c: In function 'early_identify_cpu':
arch/x86/kernel/cpu/common.c:553: error: 'struct cpuinfo_x86' has no member named 'cpu_index'
as cpu_index is only available on SMP.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix /proc/cpuinfo output on x86/Voyager
Ever since
| commit 92cb7612ae
| Author: Mike Travis <travis@sgi.com>
| Date: Fri Oct 19 20:35:04 2007 +0200
|
| x86: convert cpuinfo_x86 array to a per_cpu array
We've had an extra field in cpuinfo_x86 which is cpu_index.
Unfortunately, voyager has never initialised this, although the only
noticeable impact seems to be that /proc/cpuinfo shows all zeros for
the processor ids.
Anyway, fix this by initialising the boot CPU properly and setting the
index when the secondaries update.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: build fix on x86/Voyager
Given commits like this:
| Author: Suresh Siddha <suresh.b.siddha@intel.com>
| Date: Tue Jul 29 10:29:19 2008 -0700
|
| x86, xsave: enable xsave/xrstor on cpus with xsave support
Which deliberately expose boot cpu dependence to pieces of the system,
I think it's time to explicitly have a variable for it to prevent this
continual misassumption that the boot CPU is zero.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix x86/Voyager boot
CONFIG_SMP is used for features which work on *all* x86 boxes.
CONFIG_X86_SMP is used for standard PC like x86 boxes (for things like
multi core and apics)
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
