The TMIO mmc cannot detect the card insertion in native_hotplug mode
if the driver is probed without a card inserted.
The reason is obvious; all IRQs are disabled by tmio_mmc_host_probe(),
as follows:
tmio_mmc_disable_mmc_irqs(_host, TMIO_MASK_ALL);
The card event IRQs are first enabled by tmio_mmc_start_command() as
follows:
if (!host->native_hotplug)
irq_mask &= ~(TMIO_STAT_CARD_REMOVE | TMIO_STAT_CARD_INSERT);
tmio_mmc_enable_mmc_irqs(host, irq_mask);
If the driver is probed without a card, tmio_mmc_start_command() is
never called in the first place. So, the card is never detected.
The card event IRQs must be enabled in probe/resume functions.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
A card detect GPIO is set up only for platforms with "cd-gpios"
DT property or TMIO_MMC_USE_GPIO_CD flag. However, the driver
core always uses mmc_gpio_get_cd, which just fails with -ENOSYS
if ctx->cd_gpio is unset.
The bit 5 of the status register provides the current signal level
of the CD line. Allow to use it if the GPIO is unused.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
This property is equivalent to "disable-wp" defined in
Documentation/devicetree/bindings/mmc/mmc.txt
The TMIO MMC core calls mmc_of_parse(), and it sets
MMC_CAP2_NO_WRITE_PROTECT if "disable-wp" property is present.
We do not need a vendor-specific property to do the same thing.
Let's remove the description from the dt-binding to prevent new boards
from using it.
I am keeping the driver code for existing DT files, but added
comments that this is deprecated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
The use of this flag has been replaced with MMC_CAP2_NO_WRITE_PROTECT.
No platform defines this flag any more. Remove.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
TMIO_MMC_WRPROTECT_DISABLE is equivalent to MMC_CAP2_NO_WRITE_PROTECT.
Only the difference is the TMIO_... makes tmio_mmc_get_ro() return 0
(i.e. it does not affect mmc_gpio_get_ro() at all), while MMC_CAP2_...
returns 0 before calling ->get_ro() hook (i.e. it affects both IP own
logic and GPIO detection).
The TMIO MMC drivers do not set-up gpio_ro by themselves. Only the
possibility, if any, would be DT specifies "wp-gpios" property, and
gpio_ro is set by mmc_gpiod_request_ro() called from mmc_of_parse().
However, it does not make sense to specify "wp-gpios" property and
"toshiba,mmc-wrprotect-disable" at the same time.
I checked under arch/arm/boot/dts/ and arch/arm64/boot/dts/renesas/,
and I did not see any Renesas boards with "wp-gpios". So, this
conversion should be safe.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
TMIO_MMC_WRPROTECT_DISABLE is equivalent to MMC_CAP2_NO_WRITE_PROTECT.
The flag is propagated as follows:
renesas_sdhi_of_data::capabilities2
-> tmio_mmc_data::capabilities2
-> mmc_host::caps2
Only the difference is the TMIO_... makes tmio_mmc_get_ro() return 0
(i.e. it does not affect mmc_gpio_get_ro() at all), while MMC_CAP2_...
returns 0 before calling ->get_ro() hook (i.e. it affects both IP own
logic and GPIO detection).
The TMIO MMC drivers do not set-up gpio_ro by themselves. Only the
possibility, if any, would be DT specifies "wp-gpios" property, and
gpio_ro is set by mmc_gpiod_request_ro() called from mmc_of_parse().
However, it does not make sense to specify "wp-gpios" property and
TMIO_MMC_WRPROTECT_DISABLE at the same time.
I checked under arch/arm/boot/dts/ and arch/arm64/boot/dts/renesas/,
and I did not see any Renesas boards with "wp-gpios". So, this
conversion should be safe.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
According to the BCM2835 datasheet there are no preset value registers.
This wasn't an issue before, because we didn't propagate 1.8V support.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the max_discard value is zero, the conditional branch that checks the
trim capabilities will never update this value with max_trim.
Change the condition statement to also check the max_discard value in order
to avoid an unnecessary call to mmc_do_calc_max_discard.
Signed-off-by: Sergio Valverde <vlvrdv@gmail.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The TODO section from 2010 is obsolete. We have DMA and PM meanwhile and
we always want to handle errors better, if possible. Also DRIVER_VERSION
is not used anymore these days.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met.
Add support to set the IODELAY values depending on the various MMC
modes using the pinctrl APIs.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Errata i802 in AM572x Sitara Processors Silicon Revision 2.0, 1.1
(SPRZ429K July 2014–Revised March 2017 [1]) mentions
DCRC error interrupts (MMCHS_STAT[21] DCRC=0x1) can occur
during the tuning procedure and it has to be disabled during the
tuning procedure Implement workaround for Errata i802 here..
[1] -> http://www.ti.com/lit/er/sprz429k/sprz429k.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC tuning procedure is required to support SD card
UHS1-SDR104 mode and EMMC HS200 mode.
SDR104/HS200 DLL Tuning Procedure for AM572x platform is mentioned
in Figure 25-51. SDR104/HS200 DLL Tuning Procedure of
AM572x Sitara Processors Silicon Revision 2.0, 1.1 TRM
(SPRUHZ6I - October 2014–Revised April 2017 [1]).
The tuning function sdhci_omap_execute_tuning() will only be
called by the MMC/SD core if the corresponding speed modes
are supported by the OMAP silicon which is set in the mmc
host "caps" field.
[1] -> http://www.ti.com/lit/ug/spruhz6i/spruhz6i.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
UHS-1 DDR50 and MMC DDR52 mode require DDR bit to be
set in the configuration register (MMCHS_CON). Add
sdhci-omap specific set_uhs_signaling ops to set
this bit. Also while setting the UHSMS bit, clock should be
disabled.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add card_busy host ops in sdhci_omap to check card busy status.
The voltage switching sequence for AM572x platform is mentioned
in Figure 25-48. eMMC/SD/SDIO Power Switching Procedure of
AM572x Sitara Processors Silicon Revision 2.0, 1.1 TRM
(SPRUHZ6I - October 2014–Revised April 2017 [1]).
In the voltage switching sequence, CLKEXTFREE bit in MMCHS_CON
should also be set after switching to 1.8v which is also taken
care in the card_busy ops.
[1] -> http://www.ti.com/lit/ug/spruhz6i/spruhz6i.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Updating 'power_mode' in sdhci_omap_init_74_clocks results in
'power_mode' never updated to MMC_POWER_OFF during card
removal. This results in initialization sequence not sent to the
card during re-insertion.
Fix it here by adding sdhci_omap_set_power_mode to update power_mode.
This function can also be used later to perform operations that
are specific to a power mode (e.g, disable tuning during power off).
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As the block layer, since the conversion to blkmq, claims the host using a
context, a following nested call to mmc_claim_host(), which isn't using a
context, may hang.
Calling mmc_interrupt_hpi() and mmc_read_bkops_status() via the mmc block
layer, may suffer from this problem, as these functions are calling
mmc_claim|release_host().
Let's fix the problem by removing the calls to mmc_claim|release_host()
from the above mentioned functions and instead make the callers responsible
of claiming/releasing the host. As a matter of fact, the existing callers
already deals with it.
Fixes: 81196976ed ("mmc: block: Add blk-mq support")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
cat /sys/kernel/debug/mmc0/regs will hang up the system since
it's in runtime suspended state, so the genpd and biu_clk is
off. This patch fixes this problem by calling pm_runtime_get_sync
to wake it up before reading the registers.
Fixes: e9ed8835e9 ("mmc: dw_mmc: add runtime PM callback")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add num_caps field for dw_mci_drv_data to validate the controller
id from DT alias and non-DT ways.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 800d78bfcc ("mmc: dw_mmc: add support for implementation specific callbacks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out dw_mci_init_slot_caps to consolidate parsing
all differents types of capabilities from host contrllers.
No functional change intended.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 800d78bfcc ("mmc: dw_mmc: add support for implementation specific callbacks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The hs_timing_cfg[] array is indexed using a value derived from the
"mshcN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Fixes: 361c7fe9b0 ("mmc: dw_mmc-k3: add sd support for hi3660")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tuning can leave the IP in an active state (Buffer Read Enable bit set)
which prevents the entry to low power states (i.e. S0i3). Data reset will
clear it.
Generally tuning is followed by a data transfer which will anyway sort out
the state, so it is rare that S0i3 is actually prevented.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The optional DT parameter max-frequency could init the max bus frequency.
So take care of this, before setting the max bus frequency.
Fixes: 660fc733bd ("mmc: bcm2835: Add new driver for the sdhost controller.")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit 0a44697627.
This commit was initially intended to fix problems with hs200 and hs400
on some boards, mainly the odroid-c2. The OC2 (Rev 0.2) I have performs
well in this modes, so I could not confirm these issues.
We've had several reports about the issues being still present on (some)
OC2, so apparently, this change does not do what it was supposed to do.
Maybe the eMMC signal quality is on the edge on the board. This may
explain the variability we see in term of stability, but this is just a
guess. Lowering the max_frequency to 100Mhz seems to do trick for those
affected by the issue
Worse, the commit created new issues (CRC errors and hangs) on other
boards, such as the kvim 1 and 2, the p200 or the libretech-cc.
According to amlogic, the Tx phase should not be tuned and left in its
default configuration, so it is best to just revert the commit.
Fixes: 0a44697627 ("mmc: meson-gx: include tx phase in the tuning process")
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Makefile changes:
- enable unused-variable warning that was wrongly disabled for clang
Kconfig changes:
- warn blank 'help' and fix existing instances
- fix 'choice' behavior to not write out invisible symbols
- fix misc weirdness
Coccinell changes:
- fix false positive of free after managed memory alloc detection
- improve performance of NULL dereference detection
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJafl86AAoJED2LAQed4NsGrBEP/23mRl+8dSYkTmlczP7stZHL
tGkMQIOj85usPV4JIxYHgge6XhU0CBFXNGnDnxGeNEtwnBr5QQNxuS2nPh7rHJIN
zX5rX/vwO9lzn2FFEdKrk8bito1IgnUHUvN/d0ikPWzY7GaMy6WrIWgyThllsLNE
W7hp3cpUQOhLL9PKXwglZ/oS4iTpEs0DwN93UXU7cp7zyRa0XtFfPf7/IJ2KY+Yl
a2TEsUuZ/slJoxLhacr6+TBAgqUyewWIs0nAGdjP2EVlSjxZJQYFEQq4KnLUO2gV
wLHH2snsZSBDfPDp0M9OOb737HE17NRmuLjWxUZZOMFz8tvfUT1454zhVAN2OtSQ
cP0RqVRrFiS721oxacZpAxKFrd7o4ugUHpftJMPQAq70T9JFFbapfCLvd+OblOb/
CWmDOOR37tvop5OCuaqaSMq7a+ZQt2cO5fogiEDdnjZkk2AH5GgsAHJIrl7hH4OT
P9UMcxaWSGbutdVkM4cMUmYMuAJjiFhx1fiD+hevB1KvemXRXrqhCb0wV+GRdcoU
MXGvOGVw5WyF/vFdjpjkY7KeCgpU3BTWH3pFC2a5vUCDqgD8yndwFghJMDfSjl6d
46DIqknyveq234GK/Yz5khlbY094yL8JrJU2duva/9fGV86tgOr29xgMK28Lpyh8
AYRGO9XgmehZrEHcAQ57
=jy5l
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
"Makefile changes:
- enable unused-variable warning that was wrongly disabled for clang
Kconfig changes:
- warn about blank 'help' and fix existing instances
- fix 'choice' behavior to not write out invisible symbols
- fix misc weirdness
Coccinell changes:
- fix false positive of free after managed memory alloc detection
- improve performance of NULL dereference detection"
* tag 'kbuild-v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (21 commits)
kconfig: remove const qualifier from sym_expand_string_value()
kconfig: add xrealloc() helper
kconfig: send error messages to stderr
kconfig: echo stdin to stdout if either is redirected
kconfig: remove check_stdin()
kconfig: remove 'config*' pattern from .gitignnore
kconfig: show '?' prompt even if no help text is available
kconfig: do not write choice values when their dependency becomes n
coccinelle: deref_null: avoid useless computation
coccinelle: devm_free: reduce false positives
kbuild: clang: disable unused variable warnings only when constant
kconfig: Warn if help text is blank
nios2: kconfig: Remove blank help text
arm: vt8500: kconfig: Remove blank help text
MIPS: kconfig: Remove blank help text
MIPS: BCM63XX: kconfig: Remove blank help text
lib/Kconfig.debug: Remove blank help text
Staging: rtl8192e: kconfig: Remove blank help text
Staging: rtl8192u: kconfig: Remove blank help text
mmc: kconfig: Remove blank help text
...
The Meson GX MMC driver fails to build after commit 23c35f48f5
("pinctrl: remove include file from <linux/device.h>") because it relies
on the pinctrl/consumer.h being pulled in by the device.h header
implicitly.
Include the header explicitly to avoid the build failure.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Blank help texts are probably either a typo, a Kconfig misunderstanding,
or some kind of half-committing to adding a help text (in which case a
TODO comment would be clearer, if the help text really can't be added
right away).
Best to remove them, IMO.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The bounce buffer is gone from the MMC core, and now we found out
that there are some (crippled) i.MX boards out there that have broken
ADMA (cannot do scatter-gather), and also broken PIO so they must
use SDMA. Closer examination shows a less significant slowdown
also on SDMA-only capable Laptop hosts.
SDMA sets down the number of segments to one, so that each segment
gets turned into a singular request that ping-pongs to the block
layer before the next request/segment is issued.
Apparently it happens a lot that the block layer send requests
that include a lot of physically discontiguous segments. My guess
is that this phenomenon is coming from the file system.
These devices that cannot handle scatterlists in hardware can see
major benefits from a DMA-contiguous bounce buffer.
This patch accumulates those fragmented scatterlists in a physically
contiguous bounce buffer so that we can issue bigger DMA data chunks
to/from the card.
When tested with a PCI-integrated host (1217:8221) that
only supports SDMA:
0b:00.0 SD Host controller: O2 Micro, Inc. OZ600FJ0/OZ900FJ0/OZ600FJS
SD/MMC Card Reader Controller (rev 05)
This patch gave ~1Mbyte/s improved throughput on large reads and
writes when testing using iozone than without the patch.
dmesg:
sdhci-pci 0000:0b:00.0: SDHCI controller found [1217:8221] (rev 5)
mmc0 bounce up to 128 segments into one, max segment size 65536 bytes
mmc0: SDHCI controller on PCI [0000:0b:00.0] using DMA
On the i.MX SDHCI controllers on the crippled i.MX 25 and i.MX 35
the patch restores the performance to what it was before we removed
the bounce buffers.
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Benoît Thébaudeau <benoit@wsystem.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Benjamin Beckmeyer <beckmeyer.b@rittal.de>
Cc: stable@vger.kernel.org # v4.14+
Fixes: de3ee99b09 ("mmc: Delete bounce buffer handling")
Tested-by: Benjamin Beckmeyer <beckmeyer.b@rittal.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
specially highlighted.
First, we have converted the MMC block device from using the legacy blk
interface into using the modern blkmq interface. Not only do we get all the
nice effects from using blkmq, but it also means that new fresh nice code
replaces old rusty code. Great news to everybody that cares about MMC/SD!
It should also be noted that converting to blkmq has not been trivial, mostly
because of that we have been carrying too much of MMC specific optimizations
for the I/O request path, rather than striving to move these to the generic blk
layer. Hopefully we won't be doing that mistake, ever again.
Special thanks to Adrian Hunter (Intel) and to Linus Walleij (Linaro), who both
have been working on this for quite some time!
Second, on top of the blkmq deployment, we have enabled full support the eMMC
command queuing feature, introduced in the eMMC v.5.1 spec. This also includes
an implementation of a host driver library, supporting the corresponding CQHCI
HW. Ideally, those controllers that supports CQHCI should only need some minor
adaptations to make this play.
So far the sdhci-pci driver for the Intel GLKs and the sdhci-of-arasan driver
used on Rockchip RK3399, have enabled support for eMMC command queueing.
Worth to highlight is also that, implementing the eMMC command queuing support
has been a collaborative effort, as several people from Codeaurora, Rockchip,
Intel and Linaro have been involved. However, the work has been driven by
Adrian Hunter (Intel).
In some shadow of the above, here are the rest of the highlights:
MMC core:
- Don't remove non-removable cards during system suspend
- Add a slot-gpio helper to check capability of GPIO WP detection
MMC host:
- sdhci: Cleanups and improvements of some wakeup related code
- sdhci-pci-arasan: New variant to support Arasan PCI HW with integrated phy
- sdhci-acpi: Avoid broken UHS transfer modes on Intel CHT
- sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400
- sdhci_f_sdh30: Add ACPI support
- sdhci-esdhc-imx: Enable/disable clock at runtime suspend/resume
- sdhci-of-esdhc: A few minor fixes
- mmci: Add support for new STM32 variant
- renesas_sdhi: enable R-Car D3 (r8a77995) support
- tmio/renesas_sdhi: Re-structuring, cleanups and modernizations
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kUV+
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"There are two major achievements for MMC in this release, which
deserves to be specially highlighted.
First, we have converted the MMC block device from using the legacy
blk interface into using the modern blkmq interface. Not only do we
get all the nice effects from using blkmq, but it also means that new
fresh nice code replaces old rusty code. Great news to everybody that
cares about MMC/SD!
It should also be noted that converting to blkmq has not been trivial,
mostly because of that we have been carrying too much of MMC specific
optimizations for the I/O request path, rather than striving to move
these to the generic blk layer. Hopefully we won't be doing that
mistake, ever again.
Special thanks to Adrian Hunter (Intel) and to Linus Walleij (Linaro),
who both have been working on this for quite some time!
Second, on top of the blkmq deployment, we have enabled full support
the eMMC command queuing feature, introduced in the eMMC v.5.1 spec.
This also includes an implementation of a host driver library,
supporting the corresponding CQHCI HW. Ideally, those controllers that
supports CQHCI should only need some minor adaptations to make this
play.
So far the sdhci-pci driver for the Intel GLKs and the sdhci-of-arasan
driver used on Rockchip RK3399, have enabled support for eMMC command
queueing.
Worth to highlight is also that, implementing the eMMC command queuing
support has been a collaborative effort, as several people from
Codeaurora, Rockchip, Intel and Linaro have been involved. However,
the work has been driven by Adrian Hunter (Intel).
In some shadow of the above, here are the rest of the highlights:
MMC core:
- Don't remove non-removable cards during system suspend
- Add a slot-gpio helper to check capability of GPIO WP detection
MMC host:
- sdhci: Cleanups and improvements of some wakeup related code
- sdhci-pci-arasan: New variant to support Arasan PCI HW with integrated phy
- sdhci-acpi: Avoid broken UHS transfer modes on Intel CHT
- sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400
- sdhci_f_sdh30: Add ACPI support
- sdhci-esdhc-imx: Enable/disable clock at runtime suspend/resume
- sdhci-of-esdhc: A few minor fixes
- mmci: Add support for new STM32 variant
- renesas_sdhi: enable R-Car D3 (r8a77995) support
- tmio/renesas_sdhi: Re-structuring, cleanups and modernizations"
* tag 'mmc-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (96 commits)
mmc: mmci: fix error return code in mmci_probe()
mmc: davinci: suppress error message on EPROBE_DEFER
mmc: davinci: dont' use module_platform_driver_probe()
mmc: tmio: hide unused tmio_mmc_clk_disable/tmio_mmc_clk_enable functions
mmc: mmci: Add STM32 variant
mmc: mmci: Add support for setting pad type via pinctrl
mmc: mmci: Don't pretend all variants to have OPENDRAIN bit
mmc: mmci: Don't pretend all variants to have MCI_STARBITERR flag
mmc: mmci: Don't pretend all variants to have MMCIMASK1 register
mmc: tmio: refactor .get_ro hook
mmc: slot-gpio: add a helper to check capability of GPIO WP detection
mmc: tmio: remove dma_ops from tmio_mmc_host_probe() argument
mmc: tmio: move {tmio_}mmc_of_parse() to tmio_mmc_host_alloc()
mmc: tmio: move clk_enable/disable out of tmio_mmc_host_probe()
mmc: tmio: ioremap memory resource in tmio_mmc_host_alloc()
mmc: sh_mmcif: remove redundant initialization of 'opc'
mmc: sdhci: Rework sdhci_enable_irq_wakeups()
mmc: sdhci: Handle failure of enable_irq_wake()
mmc: sdhci: Stop exporting sdhci_enable_irq_wakeups()
mmc: sdhci-pci: Use device wakeup capability to determine MMC_PM_WAKE_SDIO_IRQ capability
...
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: f9bb304ce8 ("mmc: mmci: Add support for setting pad type via pinctrl")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This suppresses printing an error message during probe of the TI DaVinci
MMC driver when the error is EPROBE_DEFER.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This changes module_platform_driver_probe() to module_platform_driver()
in the TI DaVinci MMC driver.
On device tree systems, we can get a -EPROBE_DEFER when using a pinmux
for the CD GPIO, which results in the driver never loading because
module_platform_driver_probe() prevents it from being re-probed.
So, we replace module_platform_driver_probe() with
module_platform_driver() and removed the __init attributes accordingly.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When CONFIG_PM is disabled, we get a warning about the clock handling
being unused:
drivers/mmc/host/tmio_mmc_core.c:937:13: error: 'tmio_mmc_clk_disable' defined but not used [-Werror=unused-function]
static void tmio_mmc_clk_disable(struct tmio_mmc_host *host)
^~~~~~~~~~~~~~~~~~~~
drivers/mmc/host/tmio_mmc_core.c:929:12: error: 'tmio_mmc_clk_enable' defined but not used [-Werror=unused-function]
static int tmio_mmc_clk_enable(struct tmio_mmc_host *host)
^~~~~~~~~~~~~~~~~~~
As the clock handling is now done elsewhere, this is only used when
power management is enabled. We could make the functions as __maybe_unused,
but since there is already an #ifdef section, it seems easier to move
the helpers closer to their callers.
Fixes: b21fc29438 ("mmc: tmio: move clk_enable/disable out of tmio_mmc_host_probe()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
STM32F4 and STM32F7 MCUs has a SDIO controller that looks like
an ARM PL810.
This patch adds the STM32 variant so that mmci driver supports it.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If variant hasn't the control bit to switch pads in opendrain mode,
we can achieve the same result by asking to the pinmux driver to
configure pins for us.
This patch make the mmci driver able to do this whenever needed.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch prepares for supporting STM32 variant which doesn't
have opendrain bit in MMCIPOWER register.
ST others variant (u300, nomadik and ux500) uses MCI_OD bit whereas
others variants uses MCI_ROD bit.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch prepares for supporting the STM32 variant that
has no such bit in the status register.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Two mask registers are used in order to select which events have to
actually generate an interrupt on each IRQ line.
It seems that in the single-IRQ case it's assumed that the IRQs lines
are simply OR-ed, while the two mask registers are still present. The
driver still programs the two mask registers separately.
However the STM32 variant has only one IRQ, and also has only one mask
register.
This patch prepares for STM32 variant support by making the driver using
only one mask register.
This patch also optimize the MMCIMASK1 mask usage by caching it into
host->mask1_reg which avoid to read it into mmci_irq().
Tested only on STM32 variant. RFT for variants other than STM32
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This IP provides the write protect signal level in the status
register, but it is also possible to use GPIO for WP. They are
exclusive, so it is not efficient to call mmc_gpio_get_ro() every
time from tmio_mmc_get_ro() if we know gpio_ro is not used.
Check the capability of gpio_ro just once in the probe function,
then set mmc_gpio_get_ro to .get_ro if it is the case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Like mmc_can_gpio_cd(), mmc_can_gpio_ro() will also be useful for host
drivers to know whether GPIO write-protect detection is supported.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers need to set up various struct members for tmio_mmc_host before
calling tmio_mmc_host_probe(). Do likewise for host->dma_ops instead
of passing it as a function argument.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_of_parse() parses various DT properties and sets capability flags
accordingly. However, drivers have no chance to run platform init
code depending on such flags because mmc_of_parse() is called from
tmio_mmc_host_probe().
Move mmc_of_parse() to tmio_mmc_host_alloc() so that drivers can
handle capabilities before mmc_add_host(). Move tmio_mmc_of_parse()
likewise.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The clock is enabled in the tmio_mmc_host_probe(). It also prevents
drivers from performing platform-specific settings before mmc_add_host()
because the register access generally requires a clock.
Enable/disable the clock in drivers' probe/remove. Also, I passed
tmio_mmc_data to tmio_mmc_host_alloc() because renesas_sdhi_clk_enable()
needs it to get the private data from tmio_mmc_host.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The register region is ioremap'ed in the tmio_mmc_host_probe(), i.e.
drivers cannot get access to the hardware before mmc_add_host().
Actually, renesas_sdhi_core.c reads out the CTL_VERSION register to
complete the platform-specific settings. However, at this point,
the MMC host is already running.
Move the register ioremap to tmio_mmc_host_alloc() so that drivers
can perform platform-specific settings between tmio_mmc_host_alloc()
and tmio_mmc_host_probe().
I changed tmio_mmc_host_alloc() to return an error pointer to
propagate the return code from devm_ioremap_resource().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Variable opc is initialized with a value that is never read, opc
is later re-assigned a newer value, hence the initialization can
be removed.
Cleans up clang warning:
drivers/mmc/host/sh_mmcif.c:919:6: warning: Value stored to 'opc'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for adding more conditions for whether IRQ wakeup is
enabled, rework sdhci_enable_irq_wakeups() so that needed bits are added
instead of adding them all and then removing the unneeded bits.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that sdhci_enable_irq_wakeups() is a local function, change it to
return whether the IRQ wakeup was successfully enabled. This is in
preparation for adding more conditions for whether IRQ wakeup is enabled.
Note it is assumed, for SDHCI devices, that suspend is more important than
wakeup, so we continue to suspend regardless.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
