Clear NX_RESETING bit in netxen_tx_timeout_task() so that
the firmware watchdog task can catch need_reset request
from tx timeout.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid resetting subsys ID in i2c block. Also remove duplicate
check for address tranlsation error.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware hang detection and recovery (reset) need to
be disabled for diagnostic tools, which can run
some disruptive tests.
This adds a driver level control to turn off this
feature by diag tools.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use -EIO or -EINVAL as error codes, these can get passed up
to applications (tools).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for different windowing scheme for on chip
memory in future chip revisions. This is required by
diagnostic tools.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Future revisions need different chip reset sequence
and firmware initialization.
Also clean up some never used debug code.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Future revisions of the chip have 128 bit memory
transactions. Require drivers to implement rmw
in case of sub-128 bit accesses by driver. This
is mostly used by diagnostic tools.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sysfs entries to enable register and memory access
for diagnostic tools.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since register and onboard memory access has separate
window registers, they need not be kept under same lock.
Also, memory is always accessed from process context
(mostly for firmware init and diagnostic tools).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use common variables crb_win, ocm_win for all revisions of chip.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add access to on chip memory, this is used by
debug and diagnostic tools only.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sub 64-bit / unaligned access to oncard memory was only used
by old diagnostic tools, causes some intermittent issues when
memory controller agent is used. The new access method was
added by commit ea6828b8aa
("netxen: improve pci memory access"). Firmware init anyway
uses 8-byte strides.
This also fixes address/offset calculation for NX2031 context
memory (SIU). For NX3031, SIU uses same register offsets
as packet memory (MIU).
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use resource_size_t for PCI resource remapping instead
of unsigned long. Physical addresses can exceed range of
long data type (e.g with PAE).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The closing parenthesis was not on the right location.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After successful firmware init, return instead of
falling to error path (leading to detach) after
resuming to D0 state. This was broken in recent
firmware reset rehaul.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix minor bug in netdev tx timeout handling which could
always lead to firmware reset instead of pci function reset.
netxen_nic_reset_context() requires __NX_RESETTING bit
cleared.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add QLogic copyright, add linux-driver@qlogic.com to
MAINTAINERS.
o Delete old contact information.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redesign tx timeout handling in line with new firmware
reset design that co-ordinates with other PCI function
drivers.
o For NX3031, first try to reset PCI function's own
context before requesting firmware reset.
o For NX2031, since firmware heartbit is not supported
directly request firmware reset.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Release file firmware when no firmware reset is required.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Access on card memory through memory controller (agent)
rather than moving small pci window around. Clean up the
code for moving windows around.
o Restrict memory accesss to 64 bit, currently only firmware
download uses this.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use 8 byte strides for firmware download into card
memory since oncard memory controller needs 8 byte
(64 bit) accesses. This avoids unnecessary rmw cycles.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_INET is disabled, netxen has a build failure:
netxen_nic_main.c:(.text+0x118fd1): undefined reference to `netxen_config_indev_addr'
so make that function just an empty stub when CONFIG_INET=n.
(not "inline" since that conflicts with other declarations of it)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the offset of vlan_TCI field in cmd_desc_type0.
Signed-off-by: Amit Kumar Salecha <amit@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix typo in checking dest ip has support before
programming destip addresses.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Combine netxen_get_firmware_info(), netxen_check_options()
so that they are updated every time firmware is reset.
o Set dma mask everytime firmware is reset.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For registers accessed in fast path (interrupt / softirq)
avoid expensive I/O address translation. These registers
are directly mapped in PCI bar 0 and do not require
any window checks.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reprogram local IP addresses after firmware is reset
or after resuming from suspend.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement state machine to detect firmware hung state
and recover. Since firmware will be shared by all PCI
functions that have different class drivers (NIC or
FCOE or iSCSI), explicit hardware based serialization
is required for initializing firmware.
o Used global scratchpad register to maintain device
reference count. Every probed pci function adds to
ref count.
o Implement timer (delayed work) for each pci func
that checks firmware heartbit every 5 sec and detaches
itself if firmware is dead. Last detaching function
reloads firmware. Other functions wait for firmware
init, and re-attach themselves.
Heartbit is not supported by NX2031 firmware.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unwind allocations and release file firmware when
when firmware load fails.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a perpetual while() loop in unwinding partial
mapped tx skb on dma mapping failure.
Reported-by: "Juha Leppanen" <juha_motorsportcom@luukku.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicate calls to netxen_napi_add().
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alloc 12k skbuffs so that firmware can aggregate more
packets into one buffer. This doesn't raise memory
consumption since 9k skbs use 16k slab cache anyway.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to put ethtool_ops in data, they should be const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a couple of cases collapse some extra code like:
int retval = NETDEV_TX_OK;
...
return retval;
into
return NETDEV_TX_OK;
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the interface is put in bridged mode, destination mac
addresses are unknown to firmware. So packets take a slow
path (lower priority) in firmware reducing performance.
Firmware can cache limited number of remote unicast mac
addresses for certain interval, if "dynamic mac learning"
mode is enabled.
Driver needs to enable this "mac learning" mode in firmware.
Currently this is done through net device class sysfs entry,
possibly this can also be done upon netlink notifications to
from bridge.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate all MAC/PHY access functions into netxen_nic_hw.c
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement common function for locking/unlocking 8 hardware
semaphores used for serializing access to shared resouces
on a NIC board by different PCI functions.
As by definition, callers of these semaphore API can be
put to sleep till the semaphore is locked.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove code for phy access on unreleased NX2031 based quad-gig board.
NX3031 based production quad-gig boards do not require direct phy
access by driver.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate register definitions in netxen_nic_hdr.h
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement pci driver shutdown functionality, this helps
quiescing all PCI transaction before chipset is reset.
Amit Kumar Salecha <amit@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all tx skb mapping code into netxen_map_tx_skb().
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If netxen_need_fw_reset() return 0 [ implies firmware is up
and running], still go through dma mask check, etc.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool -K knob to control LRO in firmware.
LRO path is completely separated from GRO, LRO packets
are still fed with netif_receive_skb().
Also fix ethtool statistics to include LRO packets.
Also use correct message type while configuring interrupt coalescing.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Defer napi resouce allocation to device attach.
o Free napi resources and delete napi during detach.
This ensures right behavior across firmware reset.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Remove private workqueue in the driver, move all
scheduled tasks to keventd workqueues. This makes
ports (interfaces) of same / different NIC boards
independent, in terms of their link watchdog and
reset tasks.
o Move quick checks for link status and temperature
in timer callback, schedule watchdog task only if
link status changed or temperature reached critical
threshold.
This also fixes deadlock when thermal panic occurs,
watchdog work was flushing workqueue that it was
sitting on.
Signed-off-by: Amit Kumar Salecha <amit@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to handle aggregate packets from firmware.
Local TCP flows are automatically identified by firmware
based on the dest IP hash added by driver for local IP
addresses.
The packets are sent down on the jumbo rx ring.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary offsetof calulations on these structures:
netxen_board_info, netxen_user_old_info, netxen_new_user_info.
The offsets into the flash are fixed, don't need to be calculated.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the calculation of remaining header length in TSO
over vlan device case. This was inadvertently missed
out in patch 028afe7198 ("netxen: add vlan
tx acceleration support").
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix dma mask calculation that caps at 63-bit addressing even
when firmware advertises full 64-bit support.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change default dma mask for NX3031 to 39 bit with ability
to update it to 64-bit (if firmware indicates support). Old
code was restricting it under 4GB (32-bit), sometimes causing
failure to allocate descriptor rings on heavily populated
system. NX2031 based NICs will still get 32-bit coherent mask.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrap dest IP hashing code with #ifdef CONFIG_INET,
this feature makes no sense without INET, but other
driver can still work.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ethtool -G to tune rx and tx ring sizes
per interface basis.
This is only supported for NX3031 based cards.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable vlan tx acceleration for NX3031 if firmware advertises
capability.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Request 1532 bytes skb data size for NX3031. NX2031 firmware
needs 1760 sized buffers.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all net_device initialization into one function
netxen_setup_netdev().
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NX2031 firmware version will never be > 4.0.0, so replace
(adapter->fw_major < 4) checks with pci revision ID check.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o move all tso / checksum offload code into netxen_tso_check().
o optimize the tso header copy into simple loop.
o clean up unnecessary unions from cmd_desc_type0 struct.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o remove superfluous code to setup PCI dma watchdog for NX2031.
o disable dma watchdog completely for NX3031 (not required).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize and configure interrupt coalesing defaults
in the firmware, so that these also reflect in "ethool -c".
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NX3031 hardware requires local IP addresses for packet
accumulation (LRO). IP address hashing is required to
distinguish a local TCP flow from others (forwarded or
guest).
This patch adds listener for IP and netdev events and
configures IP address in the firmware.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o move dma mask update to netxen_start_firmware() so that
if firmware changes across suspend (e.g. file -> flash)
it reflects right dma mask.
o re-read firmware capabilities after firmware reset.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset consumer of status rings to 0 when cleaning
up sw resources. Status rings are not deleted
during suspend since they have napi objects.
This ensures correct rx processing across suspen-resume.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check temperature for all PCI functions, that can allow
graceful shutdown of all interfaces on the overheated card.
Old code was only monitoring temperature for function 0 only.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netxen: fix deadlock on dev close
The tx ring accounting fix in commit cb2107be43
("netxen: fix tx ring accounting") introduced intermittent
deadlock when inteface is going down.
This was possibly combined effect of speculative tx pause,
calling netif_tx_lock instead of queue lock and unclean
synchronization with napi which could end up unmasking
interrupt.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Use D3 reset context deletion for NX2031, it cleans up
more resources in the firmware.
o Release rx buffers after hardware context has been reset.
o Delete tx context after rx context, some firmware control
commands are sent on tx context, so it should be the last
to go.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restrict firmware reset to following cases -
o chip rev is NX2031 (firmare doesn't support heartbit).
o firmware is dead.
o previous attempt to init firmware had failed.
o we have got newer file firmware.
This speeds up module load tremendously (by upto 8 sec),
also avoids downtime for NCSI (management) pass-thru
traffic.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct firmware encoding is 8 bit major, 8 bit minor and
16 bit subversion. Flash has sizes rightly set, but original
driver submission messed it leaving 16 bit major and 8 bit
subversion.
Also fix a infinite loop when cut-thru file firmware is
invalid.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure all functions run firmware init handshake.
If PCI function 0 fails to initialize firmware, mark the
state failed so that other functions on the same board
bail out quickly instead of waiting 30s for firmware
handshake.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
wrap pci suspend() and resume() with CONFIG_PM check.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This forces every update of tx ring producer to check for
availability of space for next full TSO command. Earlier
firmware control commands didn't care to pause tx queue.
Stop the tx queue if there's not enough space to transmit one full
LSO command left on the tx ring after current transmit. This avoids
returning NETDEV_TX_BUSY after checking distance between producer
and consumer on every cpu.
Restart the tx queue only if we have cleaned up enough tx
descriptors.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the detection of cut-thru mode of the hardware (direct dma
to host) to mode configured in SRE (ingress block) rather than
onboard memory control.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vfree() does its own 'NULL' check, so no need for check before
calling it.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Followup of commits 9d21493b4b
and 08baf56108
(net: tx scalability works : trans_start)
(net: txq_trans_update() helper)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Multi queue drivers can
avoid one cache miss (on dev->trans_start) in their start_xmit()
handler.
Exceptions are NETIF_F_LLTX drivers (vxge & tehuti)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pdev->irq was not saved in netxen_adapter, causing request_irq()
with invalid irq number.
This was broken in commit be339aee63
("netxen: fix irq tear down and msix leak.").
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary length parameter since it's always 4 bytes.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This board doesn't suppot msi-x well due to msi-x table
mapping (hardware) issue.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Fix the order of irq and hardware context teardown.
Also synchronize the interrupt in dev close() before
releasing tx buffers.
o Fix possible msi-x vector leak if available vectors are
less than requested.
o Request multiple msix vectors only if hardware supports
multiple rx queues.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store msi target status register offset in adapter struct.
This avoids contention on msi_tgt_status table from interrupt
hadlers of different pci function.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Pause traffic during mac addr change.
o Enable setting mac address for NX3031.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o use standard linked list api for mac addr list management
in NX3031.
o release mac addresses in firmware in dev close().
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the distance check between tx ring producer and consumer that
could lead to tx ring wrap around.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o hold the firmware in memory across suspend, since filesystem
may not be up after resuming.
o reset the chip after requesting firmware, to minimize downtime
for NC-SI.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o move related fields into netxen_recv_context struct.
o allocate rx buffer and descriptor rings dynamically.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware starting 4.0.402 started supporting link events, disable
it for older firmwares.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aligning register offset translation table imporves performance
on rx side.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable multiple rx rings for older NX2031 chip, firmware 3.4.336
or newer supports this feature.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o remove unnecessary length parameter since register access
width is fixed 4 byte.
o remove superfluous pci_read_normalize and pci_write_normalize
functions.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reduces netxen_adapter footprint when rss (msi-x) is disabled.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for asynchronous events from firmware,
received over one of the rx rings.
Add support for event based phy interrupts, enhanced links
status reporting from firmware.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed duplicate firmware handshake, defer it until first
port (interface) is brought up.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o move tx stuff into nx_host_tx_ring structure, this will
help managing multiple tx rings in future.
o sanitize some variable names
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rearrange members to align them at right offset.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o remove unused structure defs.
o remove unnecessary includes.
o replace enums with specific #defines.
o reduce footprint of stats structure.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all DMA_39BIT_MASK macro with DMA_BIT_MASK(39)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix following warnings, by using integer firmware types.
drivers/net/netxen/netxen_nic_hw.c: In function 'netxen_load_firmware':
drivers/net/netxen/netxen_nic_hw.c:1146: warning: comparison with string literal results in unspecified behavior
drivers/net/netxen/netxen_nic_hw.c:1146: warning: comparison with string literal results in unspecified behavior
drivers/net/netxen/netxen_nic_hw.c:1146: warning: comparison with string literal results in unspecified behavior
drivers/net/netxen/netxen_nic_hw.c:1159: warning: comparison with string literal results in unspecified behavior
drivers/net/netxen/netxen_nic_hw.c:1159: warning: comparison with string literal results in unspecified behavior
drivers/net/netxen/netxen_nic_hw.c:1159: warning: comparison with string literal results in unspecified behavior
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To mark all features and bugfixes submitted since 4.0.11.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the load balancing capability of firmware
and hardware to spray traffic into different cpus through
separate rx msix interrupts.
The feature is being enabled for NX3031, NX2031 (old) will be
enabled later. This depends on msi-x and compatibility with
msi and legacy is maintained by enabling single rx ring.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o remove max_ prefix from ring sizes, since they don't really
represent max possible sizes.
o cleanup naming of rx ring types (normal, jumbo, lro).
o simplify logic to choose rx ring size, gig ports get half
rx ring of 10 gig ports.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detach network interface on PCI suspend and recreate hardware
context after resumes.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove flash size check which made sense only for ancient
boards with 1MB flash. The check is based on values read
from specific locations and fails with firmware size changes.
This prevents driver from getting right mac addresses.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove huge board config structure from each instance, read
only necessary fields from flash.
Replace board_type with port_type (1G/10G), there's another
board_type field describing card type (SFP/XFP/CX4).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAX_RCV_CTX was set to 1, there's only rx context per
PCI function.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rearrange open and close into hardware attach(), detach() and
nic up() and down(). this will be used for suspend/resume
subsequently.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o remove unused rx fragment handling code.
o imporove check for status descriptor ownership.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o set port mode after resetting device.
o prefer cut-through firmware (doesn't require on-card memory).
o load flashed firmware if newer.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support larger dma mask if firmware indicates capability
to handle larger addresses.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend copyright into 2009 and update address.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split pci probe function into smaller logical blocks.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI bar 0 is used for memory mapped register access.
If ioremap fails (returns NULL), register access results
in crash.
Use pci_ioremap_bar() instead of ioremap(), the latter
fails on on 32 bit powerpc where pci resource address is
> 32 bits.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PCI function to physical port mapping is valid only for
old firmware. New firmware (4.0.0+) abstracts this.
So driver should never try to access phy using invalid
mapping. The behavior is unpredictable when PCI functions
4-7 are enabled on the same NIC.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If for some reason, read from card memory fails the console
get flooded with failure prints. This patch confines print
under printk_ratelimit().
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following sparse warnings (multiple instances)
warning: restricted degrades to integer
warning: cast to restricted type
warning: incorrect type in argument 3 (different signedness)
warning: context imbalance in 'netxen_nic_hw_write_wx_2M' - different
lock contexts for basic block
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For NX3031 pci doorbells are not used. If unnecessary mapping
of doorbell space fails, pci probe bails out.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When compile the latest kernel on IA64 platform,I got a warning:
drivers/net/netxen/netxen_nic_main.c:203: warning: label ‘set_32_bit_mask’
defined but not used
We do not need label ‘set_32_bit_mask’ on IA64 platform,So move it to #else.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove workaround for pcie bug in early revisions of NX3031
(rev 41 or earlier). This is taken care of during firmware init.
The workaround required writing pcie config reg of every
pcie function on a card, not all of which are enabled.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Cut down msi-x vectors from 8 to 1 since only one is used for now.
o Use separate handler for msi-x, that doesn't unnecessarily scrub
msi status register.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reducing jumbo ring size below 1024 reduces throughput for old
firmwares (3.4.216 and older) running on older (NX2031) chip,
so restore it back to 1024.
This was reduced in commit 32ec803348
("netxen: reduce memory footprint").
Raising jumbo ring size from 512 to 1024, adds ~4MB per port, but
there's still big saving because of original patch (~20MB per port).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o reduce rx ring size from 8192 to 4096.
o cut down old huge lro buffers.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o set netdev->vlan_features appropriately.
o fix tso descriptor initialization for vlan case.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes a build error in absence of CONFIG_IPV6:
drivers/net/netxen/netxen_nic_main.c:1189: error: implicit declaration of function 'ipv6_hdr'
drivers/net/netxen/netxen_nic_main.c:1189: error: invalid type argument of '->'
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For NX3031 only one I/O range is mapped, so unmapping other
two which are used by older chips, causes this warning on
ppc64.
"Attempt to iounmap early bolted mapping at 0x0000000000000000"
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Bail out if pci_map_single() fails while replenishing rx ring.
o Drop packet if pci_map_{single,page}() fail in tx.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
