Pull ARM SoC DT updates from Arnd Bergmann:
"This is a rather large update for the ARM devicetree files, after a
few quieter releases, with 775 total commits and 47 branches pulled
into this one.
There are 5 new SoC types plus some minor variations, and a total of
60 new machines, so I'm limiting the summary to the main noteworthy
items:
- Apple M1 gain support for PCI and pinctrl, getting a bit closer to
a usable system out of the box.
- Qualcomm gains support for Snapdragon 690 (aka SM6350) as well as
SM7225, 11 new smartphones, and three additional Chromebooks, and
improvements all over the place.
- Samsung gains support for ExynosAutov9, an automotive version of
their smartphone SoC, but otherwise no major changes.
- Microchip adds the SAMA5D29 SoC in the SAMA5 family, and a number
of improvements for the recently added SAMA7 family. The LAN966 SoC
that was added in the platform code does not have dts files yet.
Two board files are added for the older at91sam9g20 SoC
- Aspeed supports two additional server boards using their AST2600 as
BMC, and improves support for qemu models
- Rockchip RK3566/RK3688 gets added, along with six new development
boards using RK3328/RK3399/RK3566, and one Chromebook tablet.
- Two NAS boxes are added using the ARMv4 based Gemini platform
- One new board is added to the Intel Arria SoC FPGA family
- Marvell adds one network switch based on Armada 381 and the new
MOCHAbin 7040 development board
- NXP adds support for the S32G2 automotive SoC, two imx6 based ebook
readers, and three additional development boards, which is notably
less than their usual additions, but they also gain improvements to
their many existing boards
- STmicroelectronics adds their stm32mp13 SoC family along with a
reference board
- Renesas adds new versions of their R-Car Gen3 SoCs and many updates
for their older generations
- Broadcom adds support for a number of Cisco Meraki wireless
controllers, along with two new boards and other updates for
BCM53xx/BCM47xx networking SoCs and the Raspberry Pi boards
- Mediatek improves support for the MT81xx SoCs used in Chromebooks
as well as the MT76xx networking SoCs
- NVIDIA adds a number of cleanups and additional support for more
hardware on the already supported machines
- TI K3 adds support for three new boards along with cleanups
- Toshiba adds one board for the Visconti family
- Xilinx adds five new ZynqMP based machines
- Amlogic support is added for the Radxa Zero and two Jethub home
automation controllers, along with changes to other machines
- Rob Herring continues his work on fixing dtc warnings all over the
tree.
- Minor updates for TI OMAP, Mstar, Allwinner/sunxi, Hisilicon,
Ux500, Unisoc"
* tag 'dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (720 commits)
arm64: dts: apple: j274: Expose PCI node for the Ethernet MAC address
arm64: dts: apple: t8103: Add root port interrupt routing
arm64: dts: apple: t8103: Add PCIe DARTs
arm64: apple: Add PCIe node
arm64: apple: Add pinctrl nodes
ARM: dts: arm: Update ICST clock nodes 'reg' and node names
ARM: dts: arm: Update register-bit-led nodes 'reg' and node names
arm64: dts: exynos: add chipid node for exynosautov9 SoC
ARM: dts: qcom: fix typo in IPQ8064 thermal-sensor node
Revert "arm64: dts: qcom: msm8916-asus-z00l: Add sensors"
arm64: dts: qcom: ipq6018: Remove unused 'iface_clk' property from dma-controller node
arm64: dts: qcom: ipq6018: Remove unused 'qcom,config-pipe-trust-reg' property
arm64: dts: qcom: sm8350: Add CPU topology and idle-states
arm64: dts: qcom: Drop unneeded extra device-specific includes
arm64: dts: qcom: msm8916: Drop standalone smem node
arm64: dts: qcom: Fix node name of rpm-msg-ram device nodes
arm64: dts: qcom: msm8916-asus-z00l: Add sensors
arm64: dts: qcom: msm8916-asus-z00l: Add SDCard
arm64: dts: qcom: msm8916-asus-z00l: Add touchscreen
arm64: dts: qcom: sdm845-oneplus: remove devinfo-size from ramoops node
...
With commit c709135e57 ("pinctrl: at91-pio4: add support for slew-rate")
and commit cbde6c823b ("pinctrl: at91-pio4: Fix slew rate disablement")
the slew-rate is enabled by default for each configured pin. The datasheet
specifies at chapter "Output Driver AC Characteristics" that HSIO
drivers (use in SDMMCx and QSPI0 peripherals), don't have a slewrate
setting but are rather calibrated against an external 1% resistor mounted
on the SDMMCx_CAL or QSPI0_CAL pins. Depending on the target signal
frequency and the external load, it is possible to adjust their target
output impedance. Thus set slew-rate = <0> for SDMMC (QSPI is not enabled
at the moment in device tree).
Fixes: 7540629e2f ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210915074836.6574-3-claudiu.beznea@microchip.com
Datasheet chapter "EMAC Timings" specifies that while in 3.3V domain
GMAC's MDIO pins should be configured with slew-rate enabled, while the
data + signaling pins should be configured with slew-rate disabled when
GMAC works in RGMII or RMII modes. The pin controller for SAMA7G5 sets
the slew-rate as enabled for all pins. Adapt the device tree to comply
with these.
Fixes: 7540629e2f ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210915074836.6574-2-claudiu.beznea@microchip.com
SAMA7G5-EK board has DDR3L type of memory soldered. This needs 1.35V. The
1.35V for DDR3L rail at run-time is selected by the proper configuration
on SELV2 pin (for 1.35V it needs to be in high-z state). When suspended
the MCP16502 PMIC soldered on SAMA7G5-EK will use different sets of
configuration registers to provide proper voltages on its rail. Run-time
configuration registers could be configured differently than suspend
configuration register for MCP16502 (VSEL2 affects only run-time
configuration). In suspend states the DDR3L memory soldered on SAMA7G5-EK
switches to self-refresh. Even on self-refresh it needs to be powered by
a 1.35V rail. Thus, make sure the PMIC is configured properly when system
is suspended.
Fixes: 7540629e2f (ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210930154219.2214051-2-claudiu.beznea@microchip.com
