When connector is created, if connector->polled is
DRM_CONNECTOR_POLL_CONNECT then drm_kms_helper_hotplug_event
function isn't called at drm_helper_hpd_irq_event because the
function will be called only in case of DRM_CONNECTOR_POLL_HPD.
So this patch sets always DRM_CONNECTOR_POLL_HPD flag to
connector->polled of parallel panel driver at connector creation.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch adds component framework support to resolve
the probe order issue.
Until now, exynos drm had used codes specific to exynos drm
to resolve that issue so with this patch, the specific codes
are removed.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
If any fimd channel was already active, initializing iommu will result
in a PAGE FAULT (e.e. u-boot could have turned on the display and
not disabled it before the kernel starts). This patch checks if any
channel is active before initializing iommu and disables it.
Signed-off-by: Akshu Agrawal <akshu.a@samsung.com>
Signed-off-by: Prathyush K <prathyush.k@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
In the case of that only one branch of a conditional statement is
a single statement, braces are added to both branches.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Make local symbols static, because these are used only in this
file.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Make local symbole static, because this is used only in this file.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Exynos drm driver cannot support DRIVER_HAVE_IRQ feature because it uses
driver specific one instead of routine of drm framework to
install/uninstall irq handler.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
AFAICT, the fb_base of a drm_device's mode_config is never used. It isn't
accessed by core drm, it isn't used by fbmem, and it isn't exposed to user
space.
Furthermore, it is probably supposed to be a physical address, not the
dma address mapped to the display controller, so this is just wrong.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Kernel access to the eyxnos fbdev framebuffer is via its gem object's
kernel mapping (kvaddr, stored in info->screen_base).
User space access is provided by mmap(), read() and write() of /dev/fb/fb0.
These functions also only use screen_base/screen_size().
Therefore, it is not necessary to set fix->smem_{start,len} or
fix->mmio_{start,len} fields.
This avoids leaking kernel, physical and dma mapped addresses to user
space via the ioctls FBIOGET_VSCREENINFO and FBIOGET_FSCREENINFO.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Architecture rename/split.. ARCH_QCOM is for the non-legacy platforms
(ie. device-tree, multiplatform support, etc).
Signed-off-by: Rob Clark <robdclark@gmail.com>
The hotplug detect and irq does not seem to be reliable on all devices
for some reason. For now it is more reliable to use polling, and give
preference to raw gpio status if it disagrees with the debounced hpd
status.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This makes drm_get_encoder_name() thread safe.
Reference: http://lkml.kernel.org/r/645ee6e22cad47d38a2b35c21c8d5fe3@DC1-MBX-01\
.ptsecurity.ru
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 9dc4056026 (drm/dp: let drivers specify the name of the I2C-
over-AUX adapter) introduced a new field but didn't add the proper
kernel-doc for it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
shmem_read_mapping_page() uses mapping_gfp_mask(mapping) as default gfp
mask. No reason to use shmem_read_mapping_page_gfp() directly if we want
the default behavior.
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
shmem supports page-relocations during swapin since quite some time. It
was implemented in:
commit bde05d1ccd
Author: Hugh Dickins <hughd@google.com>
Date: Tue May 29 15:06:38 2012 -0700
shmem: replace page if mapping excludes its zone
The gem-comment about wrongly placed DMA32 pages is no longer valid.
Replace it with a proper comment but keep the BUG_ON() to verify correct
shmem behavior.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The shmobile DRM driver is only useful on SuperH and shmobile unless
build testing. I am dropping the SuperH dependencies though because
the driver doesn't even build there, so in practice it is an arm-only
driver for now.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The Renesas R-Car Display Unit driver is only useful on shmobile
unless build testing. The LVDS output is useful on an even more
reduced hardware set.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
DRM is pretty much the main user of this stuff (if we ignore the sysfs
interface used by X, i.e. by the same gang of people writing the drm
drivers). So shovel it into Dave's responsibility to avoid patches
getting lost on lkml.
With this get_maintainers will rout vgaarb and switcheroo patches
correctly.
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: linux-kernel@vger.kernel.org
References: https://lkml.org/lkml/2014/5/25/94
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Started documenting drm properties for drm drivers. This patch provides
information about properties in drm, i915, psb and cdv/gma-500. Information
about other properties can be added on top of these.
v2: Added description of drm properties in armada, exynos, i2c/ch7006, noveau,
omap, qxl, radeon, rcar-du
v3: Removed "Property Object" column since it is implementation related. Property
type column refined.[Ville's review comments]
v4: Removed whitespace warnings and minor nits. [Randy's review comments]
v5: Restructured output for ENUM properties
v6: Review comments on formatting the table. [Laurent's review comments]
v7: Minor restructuring. [Laurent's review comments]
Cc: Rob Landley <rob@landley.net>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Sagar Kamble <sagar.a.kamble@intel.com>
Cc: "Purushothaman, Vijay A" <vijay.a.purushothaman@intel.com>
Cc: linux-doc@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The kerneldoc header of ttm_bo_create() was referring to another
(nonexisting) function and had a few obsolete or incorrect arguments.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The 800x600 (SVGA) screen resolution was lacking in the set of
built-in selectable EDID screen resolutions that can be used to
repair misbehaving monitor firmware.
This patch adds the related data set and expands the documentation.
Note that the SVGA bit occupies a different byte to all the existing
users of the established timing bits forcing a rework of the
ESTABLISHED_TIMINGS_BITS macro.
Tested new EDID on an aged (and misbehaving) industrial LCD panel;
existing EDIDs still pass edid-decode's checksum checks.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Carsten Emde <C.Emde@osadl.org>
Cc: linux-doc@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This just adds the defines from the DP 1.2 spec, which we
will use later.
fix some DP MST to 1.2 MST
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
It's barely alive now anyway, so give it the "coup de grâce".
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Up until now, contexts had one (and only one) backing object that was
used by the hardware to save/restore render ring contexts (via the
MI_SET_CONTEXT command). Other rings did not have or need this, so
our i915_hw_context struct had a 1:1 relationship with a a real HW
context.
With Logical Ring Contexts and Execlists, this is not possible anymore:
all rings need a backing object, and it cannot be reused. To prepare
for that, rename our contexts to the more generic term intel_context.
No functional changes.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Manual cleanup after the previous Coccinelle script.
Yes, I could write another Coccinelle script to do this but I
don't want labor-replacing robots making an honest programmer's
work obsolete (also, I'm lazy).
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As advanced by the previous patch, the ringbuffers and the engine
command streamers belong in different structs. This is so because,
while they used to be tightly coupled together, the new Logical
Ring Contexts (LRC for short) have a ringbuffer each.
In legacy code, we will use the buffer* pointer inside each ring
to get to the pertaining ringbuffer (the actual switch will be
done in the next patch). In the new Execlists code, this pointer
will be NULL and we will use instead the one inside the context
instead.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the upcoming patches we plan to break the correlation between
engine command streamers (a.k.a. rings) and ringbuffers, so it
makes sense to refactor the code and make the change obvious.
No functional changes.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm, we disable GT power saving during the end of the suspend sequence
in i915_save_state(). Doing the disabling at that point seems arbitrary.
One reason to disable it early though is to have a quiescent HW state
before we do anything else (for example save registers). So move the
disabling earlier, which also takes care canceling of the deferred RPS
enabling work done by intel_disable_gt_powersave().
Note that after the move we'll call intel_disable_gt_powersave() only
in case modeset is enabled, but that's anyway the only case where we
have it enabled in the first place.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Robert Beckett <robert.beckett@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In
commit c6df39b5ea
Author: Imre Deak <imre.deak@intel.com>
Date: Mon Apr 14 20:24:29 2014 +0300
drm/i915: get a runtime PM ref for the deferred GT powersave enabling
I added an RPM get-ref when enabling RPS from a deferred work, but forgot
to add the corresponding put-ref when canceling the work. This may leave
RPM disabled.
Note that the race is real since we run the rps enabling with a
delayed work item after resume, so leaves enough time (in contrived
examples) to fit a quick autoresum in.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Robert Beckett <robert.beckett@intel.com>
Testecase: igt/pm_rpm/system-suspend
[danvet: Mention testcase and add note.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently user space can access GEM buffers mapped to GTT through
existing mappings concurrently while the platform specific suspend
handlers are running. Since these handlers may change the HW state in a
way that would break such accesses, remove the mappings before calling
the handlers. Spotted by Ville.
Also Chris pointed out that the lists that i915_gem_release_all_mmaps()
walks through need dev->struct_mutex, so take this lock. There is a
potential deadlock against a concurrent RPM resume, resolve this by
aborting and rescheduling the suspend (Daniel).
v2:
- take struct_mutex around i915_gem_release_all_mmaps() (Chris, Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Robert Beckett <robert.beckett@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently we need to disable VCP unit clock gating around media reset
on g4x.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On gen2 the scanline counter behaves a bit differently from the
later generations. Instead of adding one to the raw scanline
counter value, we must subtract one.
On HSW/BDW the scanline counter requires a +2 adjustment on HDMI
outputs. DP outputs on the on the other require the typical +1
adjustment.
As the fixup we must apply to the hardware scanline counter
depends on several factors, compute the desired offset at modeset
time and tuck it away for when it's needed.
v2: Clarify HSW+ situation
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: "Akash Goel <akash.goels@gmail.com>"
Reviewed-by: "Sourab Gupta <sourabgupta@gmail.com>"
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78997
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The docs are a bit lacking when it comes to describing when certain
timing related events occur in the hardware. Draw a picture which
tries to capture the most important ones.
v2: Clarify a few details (Imre)
v3: Add HSW+ HDMI scanline counter numbers
Acked-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: "Sourab Gupta <sourabgupta@gmail.com>"
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently the logic to fix up the frame counter on gen3/4 assumes that
start of vblank occurs at vblank_start*htotal pixels, when in fact
it occurs htotal-hsync_start pixels earlier. Apply the appropriate
adjustment to make the frame counter more accurate.
Also fix the vblank start position for interlaced display modes.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: "Akash Goel <akash.goels@gmail.com>"
Reviewed-by: "Sourab Gupta <sourabgupta@gmail.com>"
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In interlaced modes, the pixel counter counts all pixels,
so one field will have htotal more pixels. In order to avoid
the reported position from jumping backwards when the pixel
counter is beyond the length of the shorter field, just
clamp the position the length of the shorter field. This
matches how the scanline counter based position works since
the scanline counter doesn't count the two half lines.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: "Akash Goel <akash.goels@gmail.com>"
Reviewed-by: "Sourab Gupta <sourabgupta@gmail.com>"
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel keeps on ramping up the warning level of the DRM and our display
core to make it complain whenever the locking rules are not followed.
This caught
commit 24576d2397
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Tue Mar 26 09:25:45 2013 -0700
drm/i915: enable VT switchless resume v3
introducing an unlocked access to the CRTC whilst disabling it for
suspend.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78114
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Before purging our pages (as opposed to copying back the contents from
the GPU), make sure that there is not an exposed CPU mmapping through
which the user can inspect the results.
Regression from
commit 5537252b6b
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Mar 25 13:23:06 2014 +0000
drm/i915: Invalidate our pages under memory pressure
Testcase: igt/gem_mmap/new-object
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79005
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Guo Jinxian <jinxianx.guo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have to write to the primary plane base address registrer when we
enable/disable the primary plane in response to sprite coverage. Those
writes will cause the flip counter to increment which could interfere
with the detection of CS flip completion. We could end up completing
CS flips before the CS has even executed the commands from the ring.
To avoid such issues, wait for CS flips to finish before we toggle the
primary plane on/off.
v2: Rebased due to atomic sprite update changes
Testcase: igt/kms_mmio_vs_cs_flip/setplane_vs_cs_flip
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the current code, we unconditionally touch
HSW_AUD_PIN_ELD_CP_VLD, which means we can touch it when the power
well is off, and that will trigger an "Unclaimed register" message.
Just adding the intel_crtc->config.has_audio should already avoid the
unclaimed register messsages, but since we actually need the power
well to make the Audio code work, it makes sense to also grab the
audio power domain reference, and release it when it's not needed
anymore.
I used IGT's pm_rpm to reproduce this bug, but it can probably be
reproduced on other tests that do modesets. I'm using a machine with
eDP+HDMI connected.
Regression introduced by:
commit acfa75b02e
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Apr 24 23:54:51 2014 +0200
drm/i915: Simplify audio handling on DDI ports
Credits to Daniel for suggesting this implementation.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because this will trigger "Unclaimed register" messages. All I need to
reproduce this problem is to boot my HSW machine with eDP+HDMI
connected.
Regression introduced by:
commit 9ed109a7b4
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Apr 24 23:54:52 2014 +0200
drm/i915: Track has_audio in the pipe config
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding stuff at the bottom is really no how this should be done, since
that's the place for ums/dri dungeons.
This was added in
commit a8ebba75b3
Author: Zhao Yakui <yakui.zhao@intel.com>
Date: Thu Apr 17 10:37:40 2014 +0800
drm/i915: Use the coarse ping-pong mechanism based on drm fd to dispatch the BSD command on BDW GT3
Also add a note to prevent this from happening again - people really
should be less lazy and take more time to look for a good home of
their new driver-global state.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
