When reading/writing a subpage (When HW ECC is not available/enabled)
for number of bytes not aligned to 4, the mis-aligned bytes are handled
first (by cpu copy method) before enabling the Prefetch engine to/from
'p'(start of buffer 'buf'). Then it reads/writes rest of the bytes with
the help of Prefetch engine, if available, or again using cpu copy method.
Currently, reading/writing of rest of bytes, is not done correctly since
its trying to read/write again to/from begining of buffer 'buf',
overwriting the mis-aligned bytes.
Read & write using prefetch engine got broken in commit '2c01946c'.
We never hit a scenario of not getting 'gpmc_prefetch_enable' call
success. So, problem did not get caught up.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Vimal Singh <vimal.newwork@gmail.com>
Reported-by: Bryan DE FARIA <bdefaria@adeneo-embedded.com>
Cc: stable@kernel.org [2.6.35+]
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The previous section mismatch fix for this driver wasn't entirely correct.
The sst25l_flash_info array is now used in the devinit probe func, but is
marked as initdata, so building results in the warning:
WARNING: drivers/mtd/devices/sst25l.o(.devinit.text): Section mismatch
in reference from the function sst25l_probe()
to the variable .init.data:sst25l_flash_info
Further, the remove func should be devexit rather than exit to match the
probe func.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
S25FL512S = 64MiB single die, same family as S25FL256S
S70FL01GS = 2x S25FL512S dies in one package (separate chip selects)
These devices are not sampling yet, but they are expected to be very
similar to S25FL256S, which has been tested.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
These are 32MiB parts which use a slightly different 4-byte enable
sequence from Macronix.
Default to the Spansion 4-byte scheme in set_4byte(), as it is more
likely to be copied by other vendors.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use the manufacturer ID names from cfi.h instead of hard-coding
hex constants. Introduce a JEDEC_MFR macro for clarity.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Not all configurations of the Denali controller support 4 banks. The
controller can support between 1 and 16 banks. Detect this from the
design features register.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The controller has interrupt enable/status register pairs for each bank
(along with ECC and status registers) that differ only in address offset.
Rather than providing definitions for each register, make the address a
macro so that it scales for devices with different numbers of banks.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Rather than using the PCI specific DMA API, convert to the generic
DMA API so that we can use the Denali NAND controller on other bus
types.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Coverity has reported that inside the function "onenand_block_by_block_erase()"
in onenand_base.c, we should add a check to prevent the incrementing of
possible NULL value for "region"
Signed-off-by: Maxin B. John <john.maxin@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In commit c7b28e25cb the initialization of
the backblockbits was accidentally removed. This patch returns it back,
because otherwise some NAND drivers are broken.
This problem was reported by "Saxena, Parth <parth.saxena@ti.com>" here:
http://lists.infradead.org/pipermail/linux-mtd/2011-April/035221.html
Reported-by: Saxena, Parth <parth.saxena@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Tested-by: Saxena, Parth <parth.saxena@ti.com>
Acked-by: Saxena, Parth <parth.saxena@ti.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Cc: stable@kernel.org [2.6.36+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch extends NDFC driver to support all 4 chip selects
available in NDFC NAND controller. Tested on custom 460EX board
with 2 chip select NAND device.
Artem: white-space cleanups
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Replace direct call to kmalloc for a potentially large, contiguous
buffer allocation with one to mtd_kmalloc_up_to which helps ensure the
operation can succeed under low-memory, highly- fragmented situations
albeit somewhat more slowly.
Signed-off-by: Grant Erickson <marathon96@gmail.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Introduce a common function to handle large, contiguous kmalloc buffer
allocations by exponentially backing off on the size of the requested
kernel transfer buffer until it succeeds or until the requested
transfer buffer size falls below the page size.
This helps ensure the operation can succeed under low-memory, highly-
fragmented situations albeit somewhat more slowly.
Artem: so this patch solves the problem that the kernel tries to kmalloc too
large buffers, which (a) may fail and does fail - people complain about this,
and (b) slows down the system in case of high memory fragmentation, because
the kernel starts dropping caches, writing back, swapping, etc. But we do not
really have to allocate a lot of memory to do the I/O, we may do this even with
as little as one min. I/O unit (NAND page) of RAM. So the idea of this patch is
that if the user asks to read or write a lot, we try to kmalloc a lot, with GFP
flags which make the kernel _not_ drop caches, etc. If we can allocate it - good,
if not - we try to allocate twice as less, and so on, until we reach the min.
I/O unit size, which is our last resort allocation and use the normal
GFP_KERNEL flag.
Artem: re-write the allocation function so that it makes sure the allocated
buffer is aligned to the min. I/O size of the flash.
Signed-off-by: Grant Erickson <marathon96@gmail.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Currently mtdconcat is broken for NAND. An attemtpt to create
JFFS2 filesystem on concatenation of several NAND devices fails
with OOB write errors. This patch fixes that problem.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
nand_scan calls nand_scan_tail and here we got a ecc.layout and calculate
oobavail for this layout. After calling nand_scan, we change the layout pointer
if OMAP_ECC_HAMMING_CODE_HW_ROMCODE is set. This results in not calcluated
oobavail. Mountig as jffs2 is not possible.
To fix that nand_scan has to split up in nand_scan_ident and nand_scan_tail
setting ecc.layout between these calls. So nand_scan_tail calculates oobvail
for the used layout. This is also done in serveral other platforms.
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Reviewed-by: Vimal Singh <vimal.newwork@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The 'blktrans_open()' does not handle possible '__get_mtd_device()' failures
because it does not check the error code. Moreover, the 'dev->tr->open()'
failures are not handled correctly because in this case the function just
goes ahead and gets the mtd device, then returns an error. But Instead, it
should _not_ try to get the mtd device, then it should put back the module
and the kref.
This patch fixes the issue. Note, I only compile-tested it. This patch was
inspired by a bug report about a similar issue in 2.6.34 kernels
sent by Mike Turner <admin@islandsoftware.co.uk> to the MTD mailing list:
http://lists.infradead.org/pipermail/linux-mtd/2011-April/034980.html
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Including linux/dmaengine.h fixes the missing definition of the enum
dma_ctrl_flags type used in atmel_nand_dma_op function.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Chip deselection is already done in nand_release_device. So only
duplicate code.
Signed-off-by: Jiri Pinkava <jiri.pinkava@vscht.cz>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Current implementation of s3c2410_nand_select_chip call
clk_disable every time when chip = -1 (de-select). This happend
multiple times even if chip was already de-selected. This causes
disabling clock even if they are already disabled and due to
nature of clock subsytem implementation this causes nand clock
to be disabled and newer enabled again.
Signed-off-by: Jiri Pinkava <jiri.pinkava@vscht.cz>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds CFI 1.5 support for the new Spansion S29GL-S device family.
For details, see the data sheet on the Spansion web site:
http://www.spansion.com/Support/Datasheets/S29GL_128S_01GS_00_02_e.pdf
Signed-off-by: Gernot Hoyler <Gernot.Hoyler@spansion.com>
Acked-by: Guillaume LECERF <glecerf@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
So as the ecclayout and suppage size for 4KiB page
Flex- and none-Flex OneNAND are different
the new values for none-Flex 4KiB page OneNAND memory are added.
The introduced ecclayout and suppage size are based on specification
4Gib M-die OneNAND Flash (KFM4G16Q4M, KFN8G16Q4M). Rev. 1.3, Apr. 2010
For eccpos we expose only 64 bytes out of 72, for oobfree the spare area
fields marked as "Managed by internal ECC logic for Logical Sector Number area"
are used.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The kernel already prints its build timestamp during boot, no need to
repeat it in random drivers and produce different object files each
time.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
It is nicer to dynamically create our badblock patterns than to
statically define them. The nand_create_default_bbt_descr() function
does a sufficient job of handling various bad block scanning options
for either flash-based or non-flash-based BBTs, so we might as well
use the function for both cases.
This patch simplifies and shortens our code (and removes a TODO that
I left a few months ago).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Do the following to add support for up to 4 chips on V21 devices (i.MX25 and
i.MX35):
* implement .select_chip for V21
* adjust existing NFC_V1_V2_BUF_ADDR writes to take chip select into account
* unlock all chip selects at preset_v1_v2()
* scan up to 4 devices at .probe
This has been tested on i.MX25 with two attached NAND chip (on one die).
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
drivercore: revert addition of of_match to struct device
of: fix race when matching drivers
Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time. This was unsafe
because matching is not an atomic operation with probing a driver. If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.
This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: don't delay blk_run_queue_async
scsi: remove performance regression due to async queue run
blk-throttle: Use task_subsys_state() to determine a task's blkio_cgroup
block: rescan partitions on invalidated devices on -ENOMEDIA too
cdrom: always check_disk_change() on open
block: unexport DISK_EVENT_MEDIA_CHANGE for legacy/fringe drivers
Adding the necessary MODULE_DEVICE_TABLE() information allows the driver
to be automatically loaded by udev.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Shreshtha Kumar SAHU <shreshthakumar.sahu@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix switch initialization to ensure that all switches have default routing
disabled. This guarantees that no unexpected RapidIO packets arrive to
the default port set by reset and there is no default routing destination
until it is properly configured by software.
This update also unifies handling of unmapped destinations by tsi57x, IDT
Gen1 and IDT Gen2 switches.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: <stable@kernel.org> [2.6.37+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit c21e6beb removed our queue request_fn re-enter
protection, and defaulted to always running the queues from
kblockd to be safe. This was a known potential slow down,
but should be safe.
Unfortunately this is causing big performance regressions for
some, so we need to improve this logic. Looking into the details
of the re-enter, the real issue is on requeue of requests.
Requeue of requests upon seeing a BUSY condition from the device
ends up re-running the queue, causing traces like this:
scsi_request_fn()
scsi_dispatch_cmd()
scsi_queue_insert()
__scsi_queue_insert()
scsi_run_queue()
scsi_request_fn()
...
potentially causing the issue we want to avoid. So special
case the requeue re-run of the queue, but improve it to offload
the entire run of local queue and starved queue from a single
workqueue callback. This is a lot better than potentially
kicking off a workqueue run for each device seen.
This also fixes the issue of the local device going into recursion,
since the above mentioned commit never moved that queue run out
of line.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
Revert "mmc: fix a race between card-detect rescan and clock-gate work instances"
During pci remove/rescan testing found:
pci 0000:c0:03.0: PCI bridge to [bus c4-c9]
pci 0000:c0:03.0: bridge window [io 0x1000-0x0fff]
pci 0000:c0:03.0: bridge window [mem 0xf0000000-0xf00fffff]
pci 0000:c0:03.0: bridge window [mem 0xfc180000000-0xfc197ffffff 64bit pref]
pci 0000:c0:03.0: device not available (can't reserve [io 0x1000-0x0fff])
pci 0000:c0:03.0: Error enabling bridge (-22), continuing
pci 0000:c0:03.0: enabling bus mastering
pci 0000:c0:03.0: setting latency timer to 64
pcieport 0000:c0:03.0: device not available (can't reserve [io 0x1000-0x0fff])
pcieport: probe of 0000:c0:03.0 failed with error -22
This bug was caused by commit c8adf9a3e8 ("PCI: pre-allocate
additional resources to devices only after successful allocation of
essential resources.")
After that commit, pci_hotplug_io_size is changed to additional_io_size
from minium size. So it will not go through resource_size(res) != 0
path, and will not be reset.
The root cause is: pci_bridge_check_ranges will set RESOURCE_IO flag for
pci bridge, and later if children do not need IO resource. those bridge
resources will not need to be allocated. but flags is still there.
that will confuse the the pci_enable_bridges later.
related code:
static void assign_requested_resources_sorted(struct resource_list *head,
struct resource_list_x *fail_head)
{
struct resource *res;
struct resource_list *list;
int idx;
for (list = head->next; list; list = list->next) {
res = list->res;
idx = res - &list->dev->resource[0];
if (resource_size(res) && pci_assign_resource(list->dev, idx)) {
...
reset_resource(res);
}
}
}
At last, We have to clear the flags in pbus_size_mem/io when requested
size == 0 and !add_head. becasue this case it will not go through
adjust_resources_sorted().
Just make size1 = size0 when !add_head. it will make flags get cleared.
At the same time when requested size == 0, add_size != 0, will still
have in head and add_list. because we do not clear the flags for it.
After this, we will get right result:
pci 0000:c0:03.0: PCI bridge to [bus c4-c9]
pci 0000:c0:03.0: bridge window [io disabled]
pci 0000:c0:03.0: bridge window [mem 0xf0000000-0xf00fffff]
pci 0000:c0:03.0: bridge window [mem 0xfc180000000-0xfc197ffffff 64bit pref]
pci 0000:c0:03.0: enabling bus mastering
pci 0000:c0:03.0: setting latency timer to 64
pcieport 0000:c0:03.0: setting latency timer to 64
pcieport 0000:c0:03.0: irq 160 for MSI/MSI-X
pcieport 0000:c0:03.0: Signaling PME through PCIe PME interrupt
pci 0000:c4:00.0: Signaling PME through PCIe PME interrupt
pcie_pme 0000:c0:03.0:pcie01: service driver pcie_pme loaded
aer 0000:c0:03.0:pcie02: service driver aer loaded
pciehp 0000:c0:03.0:pcie04: Hotplug Controller:
v3: more simple fix. also fix one typo in pbus_size_mem
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During initialization of vmxnet3, the state of LRO
gets out of sync with netdev->features.
This leads to very poor TCP performance in a IP forwarding
setup and is hitting many VMware users.
Simplified call sequence:
1. vmxnet3_declare_features() initializes "adapter->lro" to true.
2. The kernel automatically disables LRO if IP forwarding is enabled,
so vmxnet3_set_flags() gets called. This also updates netdev->features.
3. Now vmxnet3_setup_driver_shared() is called. "adapter->lro" is still
set to true and LRO gets enabled again, even though
netdev->features shows it's disabled.
Fix it by updating "adapter->lro", too.
The private vmxnet3 adapter flags are scheduled for removal
in net-next, see commit a0d2730c95
"net: vmxnet3: convert to hw_features".
Patch applies to 2.6.37 / 2.6.38 and 2.6.39-rc6.
Please CC: comments.
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 747df2258b ('sfc: Always map MCDI
shared memory as uncacheable') introduced a separate mapping for the
MCDI shared memory (MC_TREG_SMEM). This means we can no longer easily
include it in the register dump. Since it is not particularly useful
in debugging, substitute a recognisable dummy value.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: Take lock around probes for drm_fb_helper_hotplug_event
drm/i915: Revert i915.semaphore=1 default from 47ae63e0
vga_switcheroo: don't toggle-switch devices
drm/radeon/kms: add some evergreen/ni safe regs
drm/radeon/kms: fix extended lvds info parsing
drm/radeon/kms: fix tiling reg on fusion
We need to hold the dev->mode_config.mutex whilst detecting the output
status. But we also need to drop it for the call into
drm_fb_helper_single_fb_probe(), which indirectly acquires the lock when
attaching the fbcon.
Failure to do so exposes a race with normal output probing. Detected by
adding some warnings that the mutex is held to the backend detect routines:
[ 17.772456] WARNING: at drivers/gpu/drm/i915/intel_crt.c:471 intel_crt_detect+0x3e/0x373 [i915]()
[ 17.772458] Hardware name: Latitude E6400
[ 17.772460] Modules linked in: ....
[ 17.772582] Pid: 11, comm: kworker/0:1 Tainted: G W 2.6.38.4-custom.2 #8
[ 17.772584] Call Trace:
[ 17.772591] [<ffffffff81046af5>] ? warn_slowpath_common+0x78/0x8c
[ 17.772603] [<ffffffffa03f3e5c>] ? intel_crt_detect+0x3e/0x373 [i915]
[ 17.772612] [<ffffffffa0355d49>] ? drm_helper_probe_single_connector_modes+0xbf/0x2af [drm_kms_helper]
[ 17.772619] [<ffffffffa03534d5>] ? drm_fb_helper_probe_connector_modes+0x39/0x4d [drm_kms_helper]
[ 17.772625] [<ffffffffa0354760>] ? drm_fb_helper_hotplug_event+0xa5/0xc3 [drm_kms_helper]
[ 17.772633] [<ffffffffa035577f>] ? output_poll_execute+0x146/0x17c [drm_kms_helper]
[ 17.772638] [<ffffffff81193c01>] ? cfq_init_queue+0x247/0x345
[ 17.772644] [<ffffffffa0355639>] ? output_poll_execute+0x0/0x17c [drm_kms_helper]
[ 17.772648] [<ffffffff8105b540>] ? process_one_work+0x193/0x28e
[ 17.772652] [<ffffffff8105c6bc>] ? worker_thread+0xef/0x172
[ 17.772655] [<ffffffff8105c5cd>] ? worker_thread+0x0/0x172
[ 17.772658] [<ffffffff8105c5cd>] ? worker_thread+0x0/0x172
[ 17.772663] [<ffffffff8105f767>] ? kthread+0x7a/0x82
[ 17.772668] [<ffffffff8100a724>] ? kernel_thread_helper+0x4/0x10
[ 17.772671] [<ffffffff8105f6ed>] ? kthread+0x0/0x82
[ 17.772674] [<ffffffff8100a720>] ? kernel_thread_helper+0x0/0x10
Reported-by: Frederik Himpe <fhimpe@telenet.be>
References: https://bugs.freedesktop.org/show_bug.cgi?id=36394
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
My Q67 / i7-2600 box has rev09 Sandy Bridge graphics. It hangs
instantly when GNOME loads and it hangs so hard the reset button
doesn't work. Setting i915.semaphore=0 fixes it.
Semaphores were disabled in a1656b9090
in 2.6.38 and were re-enabled by
commit 47ae63e0c2
Merge: c59a333467cffb
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Mar 7 12:32:44 2011 +0000
Merge branch 'drm-intel-fixes' into drm-intel-next
Apply the trivial conflicting regression fixes, but keep GPU semaphores
enabled.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_gem_execbuffer.c
(It's worth noting that the offending change is i915_drv.c,
which is not a conflict.)
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Acked-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the requested device is already active, ignore the request.
This restores the original behaviour of the interface. The change was
probably an unintended side effect of
commit 66b37c6777 vga_switcheroo: split switching into two stages
which did not take into account to duplicate the !active check in the split-off
stage2.
Fix this by factoring that check out of stage1 into the debugfs_write routine.
References: https://bugzilla.kernel.org/show_bug.cgi?id=34252
Reported-by: Igor Murzov <e-mail@date.by>
Tested-by: Igor Murzov <e-mail@date.by>
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 270dac35c2.
The commits causes command timeouts on AC plug/unplug. It isn't yet
clear why. As the commit was for a single rather obscure controller,
revert the change for now.
The problem was reported and bisected by Gu Rui in bug#34692.
https://bugzilla.kernel.org/show_bug.cgi?id=34692
Also, reported by Rafael and Michael in the following thread.
http://thread.gmane.org/gmane.linux.kernel/1138771
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Gu Rui <chaos.proton@gmail.com>
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Michael Leun <lkml20100708@newton.leun.net>
Cc: Jian Peng <jipeng2005@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This moves the
if (num_registered_fb == FB_MAX)
return -ENXIO;
check _AFTER_ the call to do_remove_conflicting_framebuffers() as this
would (now in a safe way) allow a native driver to replace the
conflicting one even if all slots in registered_fb[] are taken.
This also prevents unregistering a framebuffer that is no longer
registered (vga16f will unregister at module unload time even if the
frame buffer had been unregistered earlier due to being found
conflicting).
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
