When host PF changes the number of VFs, the ECPF esw driver will get
a FW event. It should query the number of VFs enabled by host PF and
update the VF reps accordingly. Note that host PF can't change the
number of VFs dynamically, it has to reset the number of VFs to 0
before changing to a new positive number.
The host event is registered when driver is moving to switchdev mode,
and it's the last step to do in esw_offloads_init. It's unregistered
and the work queue is flushed when driver quits from switchdev mode.
In this way, the host event and devlink command are serialized.
When driver is enabling switchdev mode, pay attention to the following
two facts:
1. Host PF must not have VF initialized as the flow table in ECPF has
ENCAP enabled as default. Such flow table can't be created with
existing initialized VFs.
2. ECPF doesn't know how many VFs the host PF will enable, ECPF
offloads flow steering shall create the flow table/groups based on
the max number of VFs possibly supported by host PF.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
ECPF connects to the eswitch through vport 0xfffe. ECPF may or may
not be the eswitch manager depending on firmware configuration.
1. If ECPF is eswitch manager: ECPF will take over the eswitch manager
responsibility. A rep of the host PF shall be created at the ECPF
side for the eswitch manager to control.
2. If ECPF is not eswitch manager: host PF will be the eswitch manager,
ECPF acts similar as a VF to the host PF. Host PF will be aware
of the ECPF vport presence and control it's rep.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In offloads mode, the current implementation puts the uplink
representor at index zero of the vport reps array. It is not "natural"
to place it at index 0 since we want to put the representor for vport
0 at index 0 with the introduction of SmartNIC. A separate patch will
handle the case whether a rep is needed for vport 0 (PF vport).
So, we want to have a different placeholder for uplink vport and
representor. It was placed at the end of vport and rep array. Since
vport number can no longer act as an index into the vport or
representors arrays, use functions to map vport numbers to indices
when accessing the vports or representors arrays, and vice versa.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eswitch has two users: IB and ETH. They both register repersentors
when mlx5 interface is added, and unregister the repersentors when
mlx5 interface is removed. Ideally, each driver should only deal with
the entities which are unique to itself. However, current IB and ETH
drivers have to perform the following eswitch operations:
1. When registering, specify how many vports to register. This number
is the same for both drivers which is the total available vport
numbers.
2. When unregistering, specify the number of registered vports to do
unregister. Also, unload the repersentors which are already loaded.
It's unnecessary for eswitch driver to hands out the control of above
operations to individual driver users, as they're not unique to each
driver. Instead, such operations should be centralized to eswitch
driver. This consolidates eswitch control flow, and simplified IB and
ETH driver.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently the driver loads and unloads all reps in an unbreakable
group. However, with ECPF, the reps of special vports such as uplink
and host PF should always be loaded in switchdev mode where the reps
for VFs will be loaded on-demand and unloaded on no-demand. This is
a pre-step for that change.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently the eswitch vport reps have a valid indicator, which is
set on register and unset on unregister. However, a rep can be loaded
or not loaded when doing unregister, current driver checks if the
vport of that rep is enabled as a flag to imply the rep is loaded.
However, for ECPF, this is not valid as the host PF will enable the
vports for its VFs instead.
Add three states: {unregistered, registered, loaded}, with the
following state changes across different operations:
create: (none) -> unregistered
reg: unregistered -> registered
load: registered -> loaded
unload: loaded -> registered
unreg: registered -> unregistered
Note that the state shall only be updated inside eswitch driver rather
than individual drivers such as ETH or IB.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Suggested-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
With only PF and VF, it is sufficient to have the vport/rep array
index as the vport number. This is because PF and VF vports numbers
are consecutive serial numbers. In downstream patches with
introducing of ECPF and UPLINK vports, it's not consecutive any more.
Use getter to get specific vport/rep, and use iterator to traversal
a list of vport/rep. This hides the translation between array index
and vport number, and provides flexibility of using different
translation mechanism in the future.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Suggested-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When driver is entering offloads mode, there are two major tasks to
do: initialize flow steering and create representors. Flow steering
should make sure enough flow table/group spaces are reserved for all
reps. Representors will be created in a group, all or none.
With the introduction of ECPF, flow steering should still reserve the
same spaces. But, the representors are not always loaded/unloaded in a
single piece. Once ECPF is in offloads mode, it will get the number
of VF changing event from host PF. In such scenario, only the VF reps
should be loaded/unloaded, not the reps for special vports (such as
the uplink vport).
Thus, when entering offloads mode, driver should specify the total
number of reps, and the number of VF reps separately. When leaving
offloads mode, the cleanup should use the information self-contained
in eswitch such as number of VFs.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
E-switch offloads mode initialize/cleanup multiple steering related
entities (flow table/group). Refactor these operations to internal
helper functions for better block design.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Commands referring to vports use the following scheme:
1. When referring to my own vport, put 0 in vport and 0 in other_vport.
2. When referring to another vport, put the vport number of the
referred vport and put 1 in other_vport. It was assumed that driver
is accessing other vport when vport number is greater than 0.
With the above scheme, the case that ECPF eswitch manager is trying
to access host PF vport will fall over with scheme 1 as the vport
number is 0. This is apparently wrong as driver is trying to refer
other vport.
As such usage can only happen in the eswitch context, change relevant
functions to provide other vport input properly.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In SmartNIC mode, the eswitch manager is not necessarily the PF
(vport 0). Use a helper function to get the correct eswitch manager
vport number and cache on the eswitch instance for fast reference.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When bonding is added, driver assumes that it's RoCE LAG if no VF is
enabled. This is not enough for ECPF as the VF is enabled in host PF
side. LAG should only choose RoCE mode when both slave devices meet
conditions below:
1. E-Switch offloads mode is NONE.
2. No VF is enabled.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Merge mlx5-next shared branched into net-next,
From Bodong Wang:
1) Introduction of ECPF (Embedded CPU Physical Function), and low level
bits for mlx5 SmartNic capabilities support.
2) Vport enumeration refactoring that affect mlx5_ib and mlx5_core
From Aya Levin,
3) Add support for 50Gbps per lane link modes in the Port Type and Speed
register (PTYS)
4) Refactor low level query functions for PTYS register
5) Add support for 50Gbps per lane link modes to mlx5_ib
Note: due to a change in API in mlx5/core and a later patch from net-next,
a fixup was squashed with this merge commit that replaces FDB_UPLINK_VPORT
with MLX5_VPORT_UPLINK which exists only in upstream net-next.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
REG_32BIT_ZERO_EX and REG_64BIT are always handled in exactly the same
way, and reg_val_propagate_range() never actually sets any register to
type REG_32BIT_ZERO_EX.
Remove the redundant & unused REG_32BIT_ZERO_EX.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The function prototype used to call JITed eBPF code (ie. the type of the
struct bpf_prog bpf_func field) returns an unsigned int. The MIPS n64
ABI that MIPS64 kernels target defines that 32 bit integers should
always be sign extended when passed in registers as either arguments or
return values.
This means that when returning any value which may not already be sign
extended (ie. of type REG_64BIT or REG_32BIT_ZERO_EX) we need to perform
that sign extension in order to comply with the n64 ABI. Without this we
see strange looking test failures from test_bpf.ko, such as:
test_bpf: #65 ALU64_MOV_X:
dst = 4294967295 jited:1 ret -1 != -1 FAIL (1 times)
Although the return value printed matches the expected value, this is
only because printf is only examining the least significant 32 bits of
the 64 bit register value we returned. The register holding the expected
value is sign extended whilst the v0 register was set to a zero extended
value by our JITed code, so when compared by a conditional branch
instruction the values are not equal.
We already handle this when the return value register is of type
REG_32BIT_ZERO_EX, so simply extend this to also cover REG_64BIT.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: b6bd53f9c4 ("MIPS: Add missing file for eBPF JIT.")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Lightweight tunnels are L3 constructs that are used with IP/IP6.
For example, lwtunnel_xmit is called from ip_output.c and
ip6_output.c only.
Make the dependency explicit at least for LWT-BPF, as now they
call into IP routing.
V2: added "Reported-by" below.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Peter Oskolkov <posk@google.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
mips_cm_error_report() contains a function call that's incorrectly
indented a level further than it ought to be. Remove a tab from the
start of both affected lines.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Set the timestamp on new keys rather than leaving it unset.
Fixes: 31d5a79d7f ("KEYS: Do LRU discard in full keyrings")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
In the request_key() upcall mechanism there's a dependency loop by which if
a key type driver overrides the ->request_key hook and the userspace side
manages to lose the authorisation key, the auth key and the internal
construction record (struct key_construction) can keep each other pinned.
Fix this by the following changes:
(1) Killing off the construction record and using the auth key instead.
(2) Including the operation name in the auth key payload and making the
payload available outside of security/keys/.
(3) The ->request_key hook is given the authkey instead of the cons
record and operation name.
Changes (2) and (3) allow the auth key to naturally be cleaned up if the
keyring it is in is destroyed or cleared or the auth key is unlinked.
Fixes: 7ee02a316600 ("keys: Fix dependency loop between construction record and auth key")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Fix the creation of shortcuts for which the length of the index key value
is an exact multiple of the machine word size. The problem is that the
code that blanks off the unused bits of the shortcut value malfunctions if
the number of bits in the last word equals machine word size. This is due
to the "<<" operator being given a shift of zero in this case, and so the
mask that should be all zeros is all ones instead. This causes the
subsequent masking operation to clear everything rather than clearing
nothing.
Ordinarily, the presence of the hash at the beginning of the tree index key
makes the issue very hard to test for, but in this case, it was encountered
due to a development mistake that caused the hash output to be either 0
(keyring) or 1 (non-keyring) only. This made it susceptible to the
keyctl/unlink/valid test in the keyutils package.
The fix is simply to skip the blanking if the shift would be 0. For
example, an index key that is 64 bits long would produce a 0 shift and thus
a 'blank' of all 1s. This would then be inverted and AND'd onto the
index_key, incorrectly clearing the entire last word.
Fixes: 3cb989501c ("Add a generic associative array implementation.")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
If the sysctl 'kernel.keys.maxkeys' is set to some number n, then
actually users can only add up to 'n - 1' keys. Likewise for
'kernel.keys.maxbytes' and the root_* versions of these sysctls. But
these sysctls are apparently supposed to be *maximums*, as per their
names and all documentation I could find -- the keyrings(7) man page,
Documentation/security/keys/core.rst, and all the mentions of EDQUOT
meaning that the key quota was *exceeded* (as opposed to reached).
Thus, fix the code to allow reaching the quotas exactly.
Fixes: 0b77f5bfb4 ("keys: make the keyring quotas controllable through /proc/sys")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Two fairly small fixes: the qla one is a panic inducing use after free
and the entropy fix may seem minor but it has had huge userspace
impact thanks to an unrelated change in openssl that causes sshd to
refuse logins until it has enough entropy for the session keys, which
causes tens of minutes delay before the affected systems allow logins
after reboot.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXGb2iiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishfPmAQD/eR6G
RkGbnLfXMcP5EfAnEJAYoD8SJsR7UAAV7tdaWwEAihagqOiFmzbDKlceahaZFl27
mizmOjw4EnpIDG2W3Qw=
=BGnV
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two fairly small fixes: the qla one is a panic inducing use after free
and the entropy fix may seem minor but it has had huge userspace
impact thanks to an unrelated change in openssl that causes sshd to
refuse logins until it has enough entropy for the session keys, which
causes tens of minutes delay before the affected systems allow logins
after reboot"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: Fix panic from use after free in qla2x00_async_tm_cmd
scsi: sd: fix entropy gathering for most rotational disks
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
While trying to reproduce a reported kernel panic on arm64, I discovered
that AUTH_GSS basically doesn't work at all with older enctypes on arm64
systems with CONFIG_VMAP_STACK enabled. It turns out there still a few
places using stack memory with scatterlists, causing krb5_encrypt() and
krb5_decrypt() to produce incorrect results (or a BUG if CONFIG_DEBUG_SG
is enabled).
Tested with cthon on v4.0/v4.1/v4.2 with krb5/krb5i/krb5p using
des3-cbc-sha1 and arcfour-hmac-md5.
Signed-off-by: Scott Mayhew <smayhew@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
A fix from Russell that took a while to get applied into fixes as
I thought Russell is merging this one.
-----BEGIN PGP SIGNATURE-----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=0LSw
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.0/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fix omap4 and later lost cpu1 interrupts for periodic timer
A fix from Russell that took a while to get applied into fixes as
I thought Russell is merging this one.
* tag 'omap-for-v5.0/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: fix lack of timer interrupts on CPU1 after hotplug
The upcoming GCC 9 release extends the -Wmissing-attributes warnings
(enabled by -Wall) to C and aliases: it warns when particular function
attributes are missing in the aliases but not in their target.
In particular, it triggers for all the init/cleanup_module
aliases in the kernel (defined by the module_init/exit macros),
ending up being very noisy.
These aliases point to the __init/__exit functions of a module,
which are defined as __cold (among other attributes). However,
the aliases themselves do not have the __cold attribute.
Since the compiler behaves differently when compiling a __cold
function as well as when compiling paths leading to calls
to __cold functions, the warning is trying to point out
the possibly-forgotten attribute in the alias.
In order to keep the warning enabled, we decided to silence
this case. Ideally, we would mark the aliases directly
as __init/__exit. However, there are currently around 132 modules
in the kernel which are missing __init/__exit in their init/cleanup
functions (either because they are missing, or for other reasons,
e.g. the functions being called from somewhere else); and
a section mismatch is a hard error.
A conservative alternative was to mark the aliases as __cold only.
However, since we would like to eventually enforce __init/__exit
to be always marked, we chose to use the new __copy function
attribute (introduced by GCC 9 as well to deal with this).
With it, we copy the attributes used by the target functions
into the aliases. This way, functions that were not marked
as __init/__exit won't have their aliases marked either,
and therefore there won't be a section mismatch.
Note that the warning would go away marking either the extern
declaration, the definition, or both. However, we only mark
the definition of the alias, since we do not want callers
(which only see the declaration) to be compiled as if the function
was __cold (and therefore the paths leading to those calls
would be assumed to be unlikely).
Link: https://lore.kernel.org/lkml/20190123173707.GA16603@gmail.com/
Link: https://lore.kernel.org/lkml/20190206175627.GA20399@gmail.com/
Suggested-by: Martin Sebor <msebor@gcc.gnu.org>
Acked-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
From the GCC manual:
copy
copy(function)
The copy attribute applies the set of attributes with which function
has been declared to the declaration of the function to which
the attribute is applied. The attribute is designed for libraries
that define aliases or function resolvers that are expected
to specify the same set of attributes as their targets. The copy
attribute can be used with functions, variables, or types. However,
the kind of symbol to which the attribute is applied (either
function or variable) must match the kind of symbol to which
the argument refers. The copy attribute copies only syntactic and
semantic attributes but not attributes that affect a symbol’s
linkage or visibility such as alias, visibility, or weak.
The deprecated attribute is also not copied.
https://gcc.gnu.org/onlinedocs/gcc/Common-Function-Attributes.html
The upcoming GCC 9 release extends the -Wmissing-attributes warnings
(enabled by -Wall) to C and aliases: it warns when particular function
attributes are missing in the aliases but not in their target, e.g.:
void __cold f(void) {}
void __alias("f") g(void);
diagnoses:
warning: 'g' specifies less restrictive attribute than
its target 'f': 'cold' [-Wmissing-attributes]
Using __copy(f) we can copy the __cold attribute from f to g:
void __cold f(void) {}
void __copy(f) __alias("f") g(void);
This attribute is most useful to deal with situations where an alias
is declared but we don't know the exact attributes the target has.
For instance, in the kernel, the widely used module_init/exit macros
define the init/cleanup_module aliases, but those cannot be marked
always as __init/__exit since some modules do not have their
functions marked as such.
Suggested-by: Martin Sebor <msebor@gcc.gnu.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
The upcoming GCC 9 release extends the -Wmissing-attributes warnings
(enabled by -Wall) to C and aliases: it warns when particular function
attributes are missing in the aliases but not in their target.
In particular, it triggers here because crc32_le_base/__crc32c_le_base
aren't __pure while their target crc32_le/__crc32c_le are.
These aliases are used by architectures as a fallback in accelerated
versions of CRC32. See commit 9784d82db3 ("lib/crc32: make core crc32()
routines weak so they can be overridden").
Therefore, being fallbacks, it is likely that even if the aliases
were called from C, there wouldn't be any optimizations possible.
Currently, the only user is arm64, which calls this from asm.
Still, marking the aliases as __pure makes sense and is a good idea
for documentation purposes and possible future optimizations,
which also silences the warning.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
On module unload/remove, we need to ensure that work does not run
after we have freed resources. Concretely, cancel_delayed_work()
may return while the callback function is still running.
From kernel/workqueue.c:
The work callback function may still be running on return,
unless it returns true and the work doesn't re-arm itself.
Explicitly flush or use cancel_delayed_work_sync() to wait on it.
Link: https://lore.kernel.org/lkml/20190204220952.30761-1-TheSven73@googlemail.com/
Reported-by: Sven Van Asbroeck <thesven73@gmail.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com>
Acked-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
The following commit
441dae8f2f ("tracing: Add support for display of tgid in trace output")
removed the call to print_event_info() from print_func_help_header_irq()
which results in the ftrace header not reporting the number of entries
written in the buffer. As this wasn't the original intent of the patch,
re-introduce the call to print_event_info() to restore the orginal
behaviour.
Link: http://lkml.kernel.org/r/20190214152950.4179-1-quentin.perret@arm.com
Acked-by: Joel Fernandes <joelaf@google.com>
Cc: stable@vger.kernel.org
Fixes: 441dae8f2f ("tracing: Add support for display of tgid in trace output")
Signed-off-by: Quentin Perret <quentin.perret@arm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
This driver is for LTC3676 rather than LTC1376.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use case range for continuous range to make the code shorter.
The .readable_reg and .writable_reg implementation are exactly the same,
so use a common ltc3676_readable_writeable_reg function instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
-----BEGIN PGP SIGNATURE-----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=8mjO
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20190215' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Ensure we insert into the hctx dispatch list, if a request is marked
as DONTPREP (Jianchao)
- NVMe pull request, single missing unlock on error fix (Keith)
- MD pull request, single fix for a potentially data corrupting issue
(Nate)
- Floppy check_events regression fix (Yufen)
* tag 'for-linus-20190215' of git://git.kernel.dk/linux-block:
md/raid1: don't clear bitmap bits on interrupted recovery.
floppy: check_events callback should not return a negative number
nvme-pci: add missing unlock for reset error
blk-mq: insert rq with DONTPREP to hctx dispatch list when requeue
resulting in less memory use when DM crypt layers on DM integrity.
- Fix a long-standing DM thinp crash consistency bug that was due to
improper handling of FUA. This issue is specific to writes that
fill an entire thinp block which needs to be allocated.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcZjtbAAoJEMUj8QotnQNaTxMIANdjCyW0LlpNNuDX8hyVzXAc
HNqyFxfNk7LD4ck5jn3HuQo5nCRvne+ltjol0vOqBokITXe1a9t+GB/fWSz0yZd9
69NvwgLoaZZ0pcxeddvUQ2TAOBxCdP8O4JokQL5QgnCt4nvUOWbGQBlSQNBf/8KO
9xa+0z36pMAC2dCnClKSQgwj+ZRZOBwOKSDVl7SiM7SvbNcirtBEgtvjr8gOrKvl
SbLtoFwj8hwJFCpllwIE4ec+bHw9XsCeFEBwGiSnp6GF2sgfLbx0/EpHj09M18Vt
QCXtYxcm8IMsh0w2y4YnmSWDk8yV7P/vVyoBmMjzv/gYx+6Eyxynk8pk32LNnEc=
=jC/2
-----END PGP SIGNATURE-----
Merge tag 'for-5.0/dm-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Fix bug in DM crypt's sizing of its block integrity tag space,
resulting in less memory use when DM crypt layers on DM integrity.
- Fix a long-standing DM thinp crash consistency bug that was due to
improper handling of FUA. This issue is specific to writes that fill
an entire thinp block which needs to be allocated.
* tag 'for-5.0/dm-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm thin: fix bug where bio that overwrites thin block ignores FUA
dm crypt: don't overallocate the integrity tag space
Adjust the cq/qp mask based on the number of bar2 pages in a host page.
For user-mode rdma, the granularity of the BAR2 memory mapped to a user
rdma process during queue allocation must be based on the host page
size. The lld attributes udb_density and ucq_density are used to figure
out how many sge contexts are in a bar2 page. So the rdev->qpmask and
rdev->cqmask in iw_cxgb4 need to now be adjusted based on how many sge
bar2 pages are in a host page.
Otherwise the device fails to work on non 4k page size systems.
Fixes: 2391b0030e ("cxgb4: Remove SGE_HOST_PAGE_SIZE dependency on page size")
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Export the sge_host_page_size field to ULDs via cxgb4_lld_info, so that
iw_cxgb4 can make use of this in calculating the correct qp/cq mask.
Fixes: 2391b0030e ("cxgb4: Remove SGE_HOST_PAGE_SIZE dependency on page size")
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJcZi5LAAoJEAx081l5xIa+tSQQAKblf/Ca7QryDUbAN8JIxeJp
NuJiNP4jvvZbCod/ISktU+0zY2uKnW09//ljkEdGVg+Ilww2HHm/drs1HRUMP6QP
U6EKhoJQ99OfsBYy3J+PloBz9uS/ziGJB6YN0qcJkTZ1tvAenNqO88MWJittDZCu
ao92sB0mwW3s+R/36OtCMce3LDGPuMst98z2+tN+C4JWZW4tktYyGo/fSsZ60Gry
Hxo/X/K0F4qn5vPfPL41fH0DzXpKiuztp7WsK97YS3Wa2VeNynKaORdcWyBBQq/n
t2NvLXyW58/wzHG0u1lbWEUEor2LJZ9Cd5aVl+i8e8giR2RogTEBVbqR+hXciTPe
3lUfSXKwwus1tsiX8amcIVPIpIyZ5Hk5igfql/EHFki3zdbOESVgrFtzwas2oW6b
GljURKcNe40ZK0btaogB8m1lZ1sN2poDgB3QYrIVFywzhv+Bm3TUexmWxbho/lYW
jho3OkP3UlxHyN4TF0CjG2lEU+kCo8EPzkOoRCzjTo49DUorqjtAMcZrbFr3z5wK
oq0m9G+itUqnKmsAA9ElHsGHK4pwRpA6hwFMnOZTWb6sVZGoT4fU6pAucZoZXE8j
wlADT/HRZECes9PVqrxeqA4h8EVlira6fdV1S9YzuMHrMpwo335Suf8eghQpFkST
oOXYb8/6GfKGyz3JDxb8
=dYoy
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2019-02-15-1' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Usual pull request, little larger than I'd like but nothing too
strange in it. Willy found an bug in the lease ioctl calculations, but
it's a drm master only ioctl which makes it harder to mess with.
i915:
- combo phy programming fix
- opregion version check fix for VBT RVDA lookup
- gem mmap ioctl race fix
- fbdev hpd during suspend fix
- array size bounds check fix in pmu
amdgpu:
- Vega20 psp fix
- Add vrr range to debugfs for freesync debugging
sched:
- Scheduler race fix
vkms:
- license header fixups
imx:
- Fix CSI register offsets for i.MX51 and i.MX53.
- Fix delayed page flip completion events on i.MX6QP due to
unexpected behaviour of the PRE when issuing NOP buffer updates to
the same buffer address.
- Stop throwing errors for plane updates on disabled CRTCs when a
userspace process is killed while a plane update is pending.
- Add missing of_node_put cleanup in imx_ldb_bind"
* tag 'drm-fixes-2019-02-15-1' of git://anongit.freedesktop.org/drm/drm:
drm: Use array_size() when creating lease
drm/amdgpu/psp11: TA firmware is optional (v3)
drm/i915/opregion: rvda is relative from opregion base in opregion 2.1+
drm/i915/opregion: fix version check
drm/i915: Prevent a race during I915_GEM_MMAP ioctl with WC set
drm/i915: Block fbdev HPD processing during suspend
drm/i915/pmu: Fix enable count array size and bounds checking
drm/i915/cnl: Fix CNL macros for Voltage Swing programming
drm/i915/icl: combo port vswing programming changes per BSPEC
drm/vkms: Fix license inconsistent
drm/amd/display: Expose connector VRR range via debugfs
drm/sched: Always trace the dependencies we wait on, to fix a race.
gpu: ipu-v3: pre: don't trigger update if buffer address doesn't change
gpu: ipu-v3: Fix CSI offsets for imx53
drm/imx: imx-ldb: add missing of_node_puts
gpu: ipu-v3: Fix i.MX51 CSI control registers offset
drm/imx: ignore plane updates on disabled crtcs
Pull crypto fix from Herbert Xu:
"This fixes a crash on resume in the ccree driver"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: ccree - fix resume race condition on init
Pull networking fixes from David Miller:
1) Fix MAC address setting in mac80211 pmsr code, from Johannes Berg.
2) Probe SFP modules after being attached, from Russell King.
3) Byte ordering bug in SMC rx_curs_confirmed code, from Ursula Braun.
4) Revert some r8169 changes that are causing regressions, from Heiner
Kallweit.
5) Fix spurious connection timeouts in netfilter nat code, from Florian
Westphal.
6) SKB leak in tipc, from Hoang Le.
7) Short packet checkum issue in mlx4, similar to a previous mlx5
change, from Saeed Mahameed. The issue is that whilst padding bytes
are usually zero, it is not guarateed and the hardware doesn't take
the padding bytes into consideration when generating the checksum.
8) Fix various races in cls_tcindex, from Cong Wang.
9) Need to set stream ext to NULL before freeing in SCTP code, from Xin
Long.
10) Fix locking in phy_is_started, from Heiner Kallweit.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (54 commits)
net: ethernet: freescale: set FEC ethtool regs version
net: hns: Fix object reference leaks in hns_dsaf_roce_reset()
mm: page_alloc: fix ref bias in page_frag_alloc() for 1-byte allocs
net: phy: fix potential race in the phylib state machine
net: phy: don't use locking in phy_is_started
selftests: fix timestamping Makefile
net: dsa: bcm_sf2: potential array overflow in bcm_sf2_sw_suspend()
net: fix possible overflow in __sk_mem_raise_allocated()
dsa: mv88e6xxx: Ensure all pending interrupts are handled prior to exit
net: phy: fix interrupt handling in non-started states
sctp: set stream ext to NULL after freeing it in sctp_stream_outq_migrate
sctp: call gso_reset_checksum when computing checksum in sctp_gso_segment
net/mlx5e: XDP, fix redirect resources availability check
net/mlx5: Fix a compilation warning in events.c
net/mlx5: No command allowed when command interface is not ready
net/mlx5e: Fix NULL pointer derefernce in set channels error flow
netfilter: nft_compat: use-after-free when deleting targets
team: avoid complex list operations in team_nl_cmd_options_set()
net_sched: fix two more memory leaks in cls_tcindex
net_sched: fix a memory leak in cls_tcindex
...
Pull signal fix from Eric Biederman:
"Just a single patch that restores PTRACE_EVENT_EXIT functionality that
was accidentally broken by last weeks fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
signal: Restore the stop PTRACE_EVENT_EXIT
Flush after rule deletion bogusly hits -ENOENT. Skip rules that have
been already from nft_delrule_by_chain() which is always called from the
flush path.
Fixes: cf9dc09d09 ("netfilter: nf_tables: fix missing rules flushing per table")
Reported-by: Phil Sutter <phil@nwl.cc>
Acked-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add new accessor for bpf_object to get opaque struct btf * from it.
struct btf * is needed for all operations with BTF and it's present in
bpf_object. The only thing missing is a way to get it.
Example use-case is to get BTF key_type_id and value_type_id for a map in
bpf_object. It can be done with btf__get_map_kv_tids() but that function
requires struct btf *.
Similar API can be added for struct btf_ext but no use-case for it yet.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add bpf_map__resize() to change max_entries for a map.
Quite often necessary map size is unknown at compile time and can be
calculated only at run time.
Currently the following approach is used to do so:
* bpf_object__open_buffer() to open Elf file from a buffer;
* bpf_object__find_map_by_name() to find relevant map;
* bpf_map__def() to get map attributes and create struct
bpf_create_map_attr from them;
* update max_entries in bpf_create_map_attr;
* bpf_create_map_xattr() to create new map with updated max_entries;
* bpf_map__reuse_fd() to replace the map in bpf_object with newly
created one.
And after all this bpf_object can finally be loaded. The map will have
new size.
It 1) is quite a lot of steps; 2) doesn't take BTF into account.
For "2)" even more steps should be made and some of them require changes
to libbpf (e.g. to get struct btf * from bpf_object).
Instead the whole problem can be solved by introducing simple
bpf_map__resize() API that checks the map and sets new max_entries if
the map is not loaded yet.
So the new steps are:
* bpf_object__open_buffer() to open Elf file from a buffer;
* bpf_object__find_map_by_name() to find relevant map;
* bpf_map__resize() to update max_entries.
That's much simpler and works with BTF.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Commit c9b47cc1fa ("xsk: fix bug when trying to use both copy and
zero-copy on one queue id") moved the umem query code to the AF_XDP
core, and therefore removed the need to query the netdevice for a
umem.
This patch removes XDP_QUERY_XSK_UMEM and all code that implement that
behavior, which is just dead code.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
It contains a fix for i.MX8MQ EVK board device tree, which makes the
broken eMMC support work as expected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcVkZzAAoJEFBXWFqHsHzOjfwIALX4Sy/lU2X7M/ISKHwEIYP+
aRQ8ymXjRldTmCQusQVez8wRnphVqFI0Iyk6ktt/xzktmCCrhPDoUSKJWpwOuXj7
xTj5Rn13xNmanZ0Lox1d7w4dLEhWzYM+n2IAQT0UkcwQ6zhZQ+jx8dSbFVr15cd7
grlv5/a98IU7RvpdZzzIJvfHhey4R0diZicE6Gwha94JDGZkeyovdJ+5LvCiU7QU
lx632vsnIMWSlqNWmdKK8SvtduhRz099nhp+sZFrP/7CK8E+j1c6nV0rF2onUmkO
kvRLpw/IbBheQb9lBmcTrlf6f6Om03juy0Q682bX78qcMLvIAMczNsJNpfrNl8o=
=2/kD
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.0, 3rd round:
It contains a fix for i.MX8MQ EVK board device tree, which makes the
broken eMMC support work as expected.
* tag 'imx-fixes-5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8mq: Fix boot from eMMC
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlxS/OQQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgbjLB/0XJqH9MerWA/J+OalNANjsXQemt8Vum4OA
4C5/ViMxMbzRQm+Sc2wCAzsq30Q6pqV74aTJYtUk6J2RalaiMCbkf8zRVZKzokbj
MKUdMmHu96ZA5LEqEEHK/eMOP4j70xz5VOnTBHQ2R759DkrS2U7rHIwx9ZX8XO9V
dI8rlHot9lgF1l8DDYLuPaLsILwHPhT/Y/wUv2Js5dZ5PFHS962I76sjYlngarT5
rd49Gv8ZvNDx1wftL4JtVMy/xuMKFRHhcxpF8TrdSS648U9Rvf9l2vXR6PErHfZP
poSG5jy1vn0aPmOEWjw1sDSXPcK7ImUNTM7k8ffTPecCmmC5gCIO
=qf0D
-----END PGP SIGNATURE-----
Merge tag 'v5.0-rockchip-dts64fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
Fix for new dtc graph warnings and a regulator fix for rock64.
* tag 'v5.0-rockchip-dts64fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: enable usb-host regulators at boot on rk3328-rock64
arm64: dts: rockchip: fix graph_port warning on rk3399 bob kevin and excavator
