Move mt76x{0,2} alloc_device common code in mt76_alloc_device and
remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Block only when the busy time reaches 92%, as lower values can be reached with
heavy 802.11 traffic as well.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Based on system load and time needed by other calibration runs, the time
between dev->mac_work runs can vary quite a bit.
Calculate busy time based on the actual time difference in order to avoid
potentially over-estimating busy time, which could lead to unnecessary tx
blocking.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ED/CCA Tx blocking checks need to be run every 100 ms in order to avoid
triggering too late and keeping tx blocking on for too long
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Software encrypted packets can be passed not just through the drv_tx callback,
but also through the intermediate tx queue.
In order to deal with that, move the override to mt76x02_mac_write_txwi and
also take care of filling in the per-packet rate information
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove add_buf function pointer in mt76_queue_ops data structure since
it is no longer used
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_dma_tx_queue_skb_raw routine in dma.c and add the
corresponding entry in mt76_queue_ops data structure.
mt76_dma_tx_queue_skb_raw will be reused adding support for
mt7603 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove useless commented out configuration in mt76x0u_load_firmware
routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_mcu_rx_event i mt76-core module and remove duplicated code.
mt76_mcu_rx_event will be reused adding support for mt7603 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_mcu_get_response in mt76-core module and remove duplicated
code. mt76_mcu_get_response will be reused adding support for mt7603
driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_mcu_msg_alloc in mt76-core module and remove duplicated code.
mt76_mcu_msg_alloc will be reused adding support for mt7603 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix rate power configuration for VHT mcs 8 and 9 in
mt76x0_get_tx_power_per_rate. Moreover use the rate power
offset used for HT/VHT mcs 6 even for HT/VHT mcs 7
Fixes: b37bbc8c82 ("mt76x0: remove eeprom dependency from mt76x0_set_tx_power_per_rate")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since we implement beconing on USB now, similar interfaces should be
supported for USB as are for MMIO. Tested only on IBSS mode and
AP mode (not enabled due to lack of PS buffering).
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Configure beaconing on USB devices without PS buffering support.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Disable BEACON timer during init and configure interrupt registers
only for mmio devices.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
BSSID is not strtirct related with beaconing (for example we can have
2 STA vifs) and more related with MAC address, so initaize BSSID when
setting MAC address.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since we now support mt76x2u feature to allow set mac address
when creating interface in common code we can use it for
mt76x2u.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use vif_mask to count interfaces to allow to set mac address in HW
if there is only one interface and report error if we create
interface with wrong BSSID resulting in already used index.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
commit da215354eb ("ASoC: simple-card: merge simple-scu-card")
merged simple-card and simple-scu-card. Then it had refcount
underflow bug. This patch fixup it.
We will get below error without this patch.
OF: ERROR: Bad of_node_put() on /sound
CPU: 3 PID: 237 Comm: kworker/3:1 Not tainted 5.0.0-rc6+ #1514
Hardware name: Renesas H3ULCB Kingfisher board based on r8a7795 ES2.0+ (DT)
Workqueue: events deferred_probe_work_func
Call trace:
dump_backtrace+0x0/0x150
show_stack+0x24/0x30
dump_stack+0xb0/0xec
of_node_release+0xd0/0xd8
kobject_put+0x74/0xe8
of_node_put+0x24/0x30
__of_get_next_child+0x50/0x70
of_get_next_child+0x40/0x68
asoc_simple_card_probe+0x604/0x730
platform_drv_probe+0x58/0xa8
...
Reported-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
At the context with *rdev available, regulator core provides
rdev_get_id()/rdev_get_regmap() APIs to get regulator id and *regmap.
So no need to store them in struct stpmic1_regulator.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no vsel_reg/vsel_mask settings for PV88060_ID_SWx, so don't use
pv88060_ldo_ops for PV88060_SW. The PV88060_ID_SWx is fixed voltage,
set .fixed_uV instead of .min_uV then regulator core will automatically
support get_voltage and list_voltage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Topology resources are no longer needed if any element failed to load.
Signed-off-by: Bard liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
* Work on the new debugging infrastructure continues;
* FTM (Fine Timing Measurement) initiator and responder implementation;
* Support for a new device family started;
* Bump supported FW API to 46;
* General bugfixes;
* Other cleanups;
-----BEGIN PGP SIGNATURE-----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=B8hU
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2019-02-14' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Fourth batch of iwlwifi patches intended for v5.1
* Work on the new debugging infrastructure continues;
* FTM (Fine Timing Measurement) initiator and responder implementation;
* Support for a new device family started;
* Bump supported FW API to 46;
* General bugfixes;
* Other cleanups;
- Dietmar Eggemann noticed an issue with IRQ migration during CPU hotplug
stress testing.
- Mathieu Desnoyers noticed that a previous fix broke optimised kprobes.
- Robin Murphy noticed a case where we were not clearing the dma_ops.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=KSCg
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"A few ARM fixes:
- Dietmar Eggemann noticed an issue with IRQ migration during CPU
hotplug stress testing.
- Mathieu Desnoyers noticed that a previous fix broke optimised
kprobes.
- Robin Murphy noticed a case where we were not clearing the dma_ops"
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8835/1: dma-mapping: Clear DMA ops on teardown
ARM: 8834/1: Fix: kprobes: optimized kprobes illegal instruction
ARM: 8824/1: fix a migrating irq bug when hotplug cpu
- Have kprobes not use copy_from_user() to access kernel addresses,
because kprobes can legitimately poke at bad kernel memory, which
will fault. Copy from user code should never fault in kernel space.
Using probe_mem_read() can handle kernel address space faulting.
- Put back the entries counter in the tracing output that was accidentally
removed.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXGb7BxQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qqvaAQC66gQ79frSW7xPjJ4Y+qLIm0YDV18i
aCHowAXxDeK3qAEA3sDeELAPVupacPrzZc6zejI+bf0HArPe08n3vlHwAQw=
=uUQj
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.0-rc4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Two more tracing fixes
- Have kprobes not use copy_from_user() to access kernel addresses,
because kprobes can legitimately poke at bad kernel memory, which
will fault. Copy from user code should never fault in kernel space.
Using probe_mem_read() can handle kernel address space faulting.
- Put back the entries counter in the tracing output that was
accidentally removed"
* tag 'trace-v5.0-rc4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix number of entries in trace header
kprobe: Do not use uaccess functions to access kernel memory that can fault
This is a remnant of commit 70a7fb80e8 ("regulator: core: Fix nested
locking of supplies").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes another set of errors from the refactoring of literals
to mask preproccesor definitions.
Found by debugging a broken voltage setup on Orange Pi One Plus.
Fixes: db4a555f7c ("regulator: axp20x: use defines for masks")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The authorize reply can be empty, for example when the ticket used to
build the authorizer is too old and TAG_BADAUTHORIZER is returned from
the service. Calling ->verify_authorizer_reply() results in an attempt
to decrypt and validate (somewhat) random data in au->buf (most likely
the signature block from calc_signature()), which fails and ends up in
con_fault_finish() with !con->auth_retry. The ticket isn't invalidated
and the connection is retried again and again until a new ticket is
obtained from the monitor:
libceph: osd2 192.168.122.1:6809 bad authorize reply
libceph: osd2 192.168.122.1:6809 bad authorize reply
libceph: osd2 192.168.122.1:6809 bad authorize reply
libceph: osd2 192.168.122.1:6809 bad authorize reply
Let TAG_BADAUTHORIZER handler kick in and increment con->auth_retry.
Cc: stable@vger.kernel.org
Fixes: 5c056fdc5b ("libceph: verify authorize reply on connect")
Link: https://tracker.ceph.com/issues/20164
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
RING_CONTROL reg was not written due to wrong address, hence all
the subsequent ring flush was timing out.
Fixes: a371c10ea4 ("mailbox: bcm-flexrm-mailbox: Fix FlexRM ring flush sequence")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The mbox_flush() function can be used by drivers that are built as
modules, so the function needs to be exported.
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Update the setup sequence on MT7622 to apply the same flow with MT7663U
and MT7668U USB [1] as much as possible. These additional commands are
required to parse the corresponding event to determine what current state
the Bluetooth device is on and thus it's necessary to extend
mtk_hci_wmt_sync to support the reading status in the same patch.
[1] http://lists.infradead.org/pipermail/linux-mediatek/2019-January/017074.html
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pass a structure pointer to mtk_hci_wmt_sync rather than several arguments
to avoid take up additional stack area and be better to read the code.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Restore bdev->tx_state with clearing bit BTMTKUART_TX_WAIT_VND_EVT
when there is an error on waiting for the corresponding event.
Fixes: 7237c4c9ec ("Bluetooth: mediatek: Add protocol support for MediaTek serial devices")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
add a trivial typo fix from speicfic to specific
Fixes: 7237c4c9ec ("Bluetooth: mediatek: Add protocol support for MediaTek serial devices")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
size = struct_size(instance, entry, count);
instance = alloc(size, GFP_KERNEL)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, change the following form:
sizeof(*ev) + ev->num_hndl * sizeof(struct hci_comp_pkts_info)
to :
struct_size(ev, handles, ev->num_hndl)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_dev struct hdev is referenced in work queues and timers started
by open() in some protocols. This creates a race between the
initialization function and the work or timer which can result hdev
being dereferenced while it is still null.
The syzbot report contains a reliable reproducer which causes a null
pointer dereference of hdev in hci_uart_write_work() by making the
memory allocation for hdev fail.
To fix this, ensure hdev is valid from before calling a protocol's
open() until after calling a protocol's close().
Reported-by: syzbot+257790c15bcdef6fe00c@syzkaller.appspotmail.com
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After commit cc9f8349cb ("arm64: crypto: add NEON accelerated XOR
implementation"), Clang builds for arm64 started failing with the
following error message.
arch/arm64/lib/xor-neon.c:58:28: error: incompatible pointer types
assigning to 'const unsigned long *' from 'uint64_t *' (aka 'unsigned
long long *') [-Werror,-Wincompatible-pointer-types]
v3 = veorq_u64(vld1q_u64(dp1 + 6), vld1q_u64(dp2 + 6));
^~~~~~~~
/usr/lib/llvm-9/lib/clang/9.0.0/include/arm_neon.h:7538:47: note:
expanded from macro 'vld1q_u64'
__ret = (uint64x2_t) __builtin_neon_vld1q_v(__p0, 51); \
^~~~
There has been quite a bit of debate and triage that has gone into
figuring out what the proper fix is, viewable at the link below, which
is still ongoing. Ard suggested disabling this warning with Clang with a
pragma so no neon code will have this type of error. While this is not
at all an ideal solution, this build error is the only thing preventing
KernelCI from having successful arm64 defconfig and allmodconfig builds
on linux-next. Getting continuous integration running is more important
so new warnings/errors or boot failures can be caught and fixed quickly.
Link: https://github.com/ClangBuiltLinux/linux/issues/283
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In valid_user_regs() we treat SSBS as a RES0 bit, and consequently it is
unexpectedly cleared when we restore a sigframe or fiddle with GPRs via
ptrace.
This patch fixes valid_user_regs() to account for this, updating the
function to refer to the latest ARM ARM (ARM DDI 0487D.a). For AArch32
tasks, SSBS appears in bit 23 of SPSR_EL1, matching its position in the
AArch32-native PSR format, and we don't need to translate it as we have
to for DIT.
There are no other bit assignments that we need to account for today.
As the recent documentation describes the DIT bit, we can drop our
comment regarding DIT.
While removing SSBS from the RES0 masks, existing inconsistent
whitespace is corrected.
Fixes: d71be2b6c0 ("arm64: cpufeature: Detect SSBS and advertise to userspace")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
During hci down we observed IBS sleep commands are queued in the Tx
buffer and hci_uart_write_work is sending data to the chip which is
not required as the chip is powered off. This patch will disable IBS
and flush the Tx buffer before we turn off the chip.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch will help to stop frame reassembly errors while changing
the baudrate. This is because host send a change baudrate request
command to the chip with 115200 bps, Whereas chip will change their
UART clocks to the enable for new baudrate and sends the response
for the change request command with newer baudrate, On host side
we are still operating in 115200 bps which results of reading garbage
data. Here we are pulling RTS line, so that chip we will wait to send data
to host until host change its baudrate.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
wcn3990 requires a power pulse to turn ON/OFF along with
regulators. Sometimes we are observing the power pulses are sent
out with some time delay, due to queuing these commands. This is
causing synchronization issues with chip, which intern delay the
chip setup or may end up with communication issues.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Variable count is never zero inside the loop so the check if count is
zero is redundant and can be removed. Fix this.
Detected by CoverityScan, CID#1466880 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After moving an XFRM interface to another namespace it stays associated
with the original namespace (net in `struct xfrm_if` and the list keyed
with `xfrmi_net_id`), allowing processes in the new namespace to use
SAs/policies that were created in the original namespace. For instance,
this allows a keying daemon in one namespace to establish IPsec SAs for
other namespaces without processes there having access to the keys or IKE
credentials.
This worked fine for outbound traffic, however, for inbound traffic the
lookup for the interfaces and the policies used the incorrect namespace
(the one the XFRM interface was moved to).
Fixes: f203b76d78 ("xfrm: Add virtual xfrm interfaces")
Signed-off-by: Tobias Brunner <tobias@strongswan.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
