Currently driver checks for Firmware state change from ISR context, and
only when there are interrupts tied with no I/O completions. We have seen
multiple cases where doorbell interrupts sent by firmware to indicate FW
state change are not processed by driver and it takes long time for driver
to trigger OCR. And if there are no IOs running, since we only check the FW
state as part of ISR code, fault goes undetected by driver and OCR will not
be triggered.
This patch introduces a separate workqueue that runs every one second to
detect Firmware FAULT state and trigger reset immediately. As an
additional gain, removing PCI reads from ISR to check FW state results in
improved performance as well.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modify driver version to 27.100.00.00 (which is equivalent to PH8 OOB
driver)
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently driver is modifying both current & NVRAM/persistent data in
Manufacturing page11. Driver should change only current copy of
Manufacturing page11. It should not modify the persistent data.
So removed the section of code where driver is modifying the persistent
data of Manufacturing page11.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If EEDPTagMode field in manufacturing page11 is set then unset it. This is
needed to fix a hardware bug only in SAS3/SAS2 cards. So, skipping
EEDPTagMode changes in Manufacturing page11 for SAS 3.5 controllers.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is to fix SYNC CACHE and START STOP command failures with
DID_NO_CONNECT during driver unload.
In driver's IO submission patch (i.e. in driver's .queuecommand()) driver
won't allow any SCSI commands to the IOC when ioc->remove_host flag is set
and hence SYNC CACHE commands which are issued to the target drives (where
write cache is enabled) during driver unload time is failed with
DID_NO_CONNECT status.
Now modified the driver to allow SYNC CACHE and START STOP commands to IOC,
even when remove_host flag is set.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Call sas_remove_host() before removing the target devices in the driver's
.remove() callback function(i.e. during driver unload time). So that
driver can provide a way to allow SYNC CACHE, START STOP unit commands
etc. (which are issued from SML) to the target drives during driver unload
time.
Once sas_remove_host() is called before removing the target drives then
driver can just clean up the resources allocated for target devices and no
need to call sas_port_delete_phy(), sas_port_delete() API's as these API's
internally called from sas_remove_host().
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change. Doing code refactor of function
mpt3sas_wait_for_ioc() for better readability.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional changes. This section of code "wait for IOC to be
operational" is used in many places across the driver. Factor this code
out into a new mpt3sas_wait_for_ioc().
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added new #define variable IOC_OPERATIONAL_WAIT_COUNT and it replaces hard
coded value '10' in all the places where driver is waiting for the IOC to
become operational.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for Aero/Sea controllers and add warning for configurable
secure type IOC.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updating MPI headers to the latest version 2.6.7 to add support to the
driver to detect the new 3816 and 3916 chip based controllers. Separate
out firmware image data from mpi2_ioc.h to new file mpi2_image.h
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I overlooked this statement when I recently converted the function result
type from struct scsi_cmnd * to bool. No change to object code.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes a spelling typo in MODULE_PARM_DESC of
ql2xplogiabsentdevice.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/hisi_sas/hisi_sas_v1_hw.c: In function 'start_delivery_v1_hw':
drivers/scsi/hisi_sas/hisi_sas_v1_hw.c:907:20: warning:
variable 'dq_list' set but not used [-Wunused-but-set-variable]
drivers/scsi/hisi_sas/hisi_sas_v2_hw.c: In function 'start_delivery_v2_hw':
drivers/scsi/hisi_sas/hisi_sas_v2_hw.c:1671:20: warning:
variable 'dq_list' set but not used [-Wunused-but-set-variable]
drivers/scsi/hisi_sas/hisi_sas_v3_hw.c: In function 'start_delivery_v3_hw':
drivers/scsi/hisi_sas/hisi_sas_v3_hw.c:889:20: warning:
variable 'dq_list' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit
fa222db0b0 ("scsi: hisi_sas: Don't lock DQ for complete task sending")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reading throught the new driver, I noticed that this cannot work on
big-endian CPUs, and the old DAC960 had exactly the same behavior.
To document this for the future, add a Kconfig dependency that prevents it
from being included in big-endian kernels. Since the hardware is really
old and we never had a working driver on it for big-endian platforms,
it's unlikely to make a difference to users.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Putting a 1024 byte data structure on the stack is generally a bad idea.
On 32-bit systems, it also triggers a compile-time warning when building
with -Og:
drivers/scsi/myrs.c: In function 'myrs_get_ctlr_info':
drivers/scsi/myrs.c:212:1: error: the frame size of 1028 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
We only really need three members of the structure, so just read them
manually here instead of copying the entire structure.
Fixes: 7726618639 ("scsi: myrs: Add Mylex RAID controller (SCSI interface)")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The addition of a spinlock in lpfc_debugfs_nodelist_data() introduced
a bug that lets us not skip NULL pointers correctly, as noticed by
gcc-8:
drivers/scsi/lpfc/lpfc_debugfs.c: In function 'lpfc_debugfs_nodelist_data.constprop':
drivers/scsi/lpfc/lpfc_debugfs.c:728:13: error: 'nrport' may be used uninitialized in this function [-Werror=maybe-uninitialized]
if (nrport->port_role & FC_PORT_ROLE_NVME_INITIATOR)
This changes the logic back to what it was, while keeping the added
spinlock.
Fixes: 9e21017826 ("scsi: lpfc: Synchronize access to remoteport via rport")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
gcc warns that the 12 byte fw_version field might not be long enough to
contain the generated firmware name string:
drivers/scsi/myrb.c: In function 'myrb_get_hba_config':
drivers/scsi/myrb.c:1052:38: error: '%02d' directive writing between 2 and 3 bytes into a region of size between 2 and 5 [-Werror=format-overflow=]
sprintf(cb->fw_version, "%d.%02d-%c-%02d",
^~~~
drivers/scsi/myrb.c:1052:26: note: directive argument in the range [0, 255]
sprintf(cb->fw_version, "%d.%02d-%c-%02d",
^~~~~~~~~~~~~~~~~
drivers/scsi/myrb.c:1052:2: note: 'sprintf' output between 10 and 14 bytes into a destination of size 12
sprintf(cb->fw_version, "%d.%02d-%c-%02d",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
enquiry2->fw.major_version,
~~~~~~~~~~~~~~~~~~~~~~~~~~~
enquiry2->fw.minor_version,
~~~~~~~~~~~~~~~~~~~~~~~~~~~
enquiry2->fw.firmware_type,
~~~~~~~~~~~~~~~~~~~~~~~~~~~
enquiry2->fw.turn_id);
~~~~~~~~~~~~~~~~~~~~~
I have not checked whether there are appropriate range checks before the
sprintf, but there is a range check after it that will bail out in case
of out of range version numbers. This means we can simply use snprintf()
instead of sprintf() to limit the output buffer size, and it will work
correctly.
Fixes: 081ff398c5 ("scsi: myrb: Add Mylex RAID controller (block interface)")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is a set of minor small (and safe changes) that didn't make the
initial pull request plus some bug fixes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCW9zD2CYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishaMPAQDwYDbt
wsCd4SlAPz1PzAV25GL3zeBpk5UeCjv2/nIzEgEA6P+poJC85aVznrjNQ2kUyWdS
h/NrvG9UJmvVngKpDWQ=
=FHI8
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is a set of minor small (and safe changes) that didn't make the
initial pull request plus some bug fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: mvsas: Remove set but not used variable 'id'
scsi: qla2xxx: Remove two arguments from qlafx00_error_entry()
scsi: qla2xxx: Make sure that qlafx00_ioctl_iosb_entry() initializes 'res'
scsi: qla2xxx: Remove a set-but-not-used variable
scsi: qla2xxx: Make qla2x00_sysfs_write_nvram() easier to analyze
scsi: qla2xxx: Declare local functions 'static'
scsi: qla2xxx: Improve several kernel-doc headers
scsi: qla2xxx: Modify fall-through annotations
scsi: 3w-sas: 3w-9xxx: Use unsigned char for cdb
scsi: mvsas: Use dma_pool_zalloc
scsi: target: Don't request modules that aren't even built
scsi: target: Set response length for REPORT TARGET PORT GROUPS
We plan to enable building the PCMCIA core and drivers, and the
non-prefixed PCMCIA name clashes with some arch headers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
-----BEGIN PGP SIGNATURE-----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=NFEB
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20181026' of git://git.kernel.dk/linux-block
Pull more block layer updates from Jens Axboe:
- Set of patches improving support for zoned devices. This was ready
before the merge window, but I was late in picking it up and hence it
missed the original pull request (Damien, Christoph)
- libata no link power management quirk addition for a Samsung drive
(Diego Viola)
- Fix for a performance regression in BFQ that went into this merge
window (Federico Motta)
- Fix for a missing dma mask setting return value check (Gustavo)
- Typo in the gdrom queue failure case (me)
- NULL pointer deref fix for xen-blkfront (Vasilis Liaskovitis)
- Fixing the get_rq trace point placement in blk-mq (Xiaoguang Wang)
- Removal of a set-but-not-read variable in cdrom (zhong jiang)
* tag 'for-linus-20181026' of git://git.kernel.dk/linux-block:
libata: Apply NOLPM quirk for SAMSUNG MZ7TD256HAFV-000L9
block, bfq: fix asymmetric scenarios detection
gdrom: fix mistake in assignment of error
blk-mq: place trace_block_getrq() in correct place
block: Introduce blk_revalidate_disk_zones()
block: add a report_zones method
block: Expose queue nr_zones in sysfs
block: Improve zone reset execution
block: Introduce BLKGETNRZONES ioctl
block: Introduce BLKGETZONESZ ioctl
block: Limit allocation of zone descriptors for report zones
block: Introduce blkdev_nr_zones() helper
scsi: sd_zbc: Fix sd_zbc_check_zones() error checks
scsi: sd_zbc: Reduce boot device scan and revalidate time
scsi: sd_zbc: Rearrange code
cdrom: remove set but not used variable 'tocuse'
skd: fix unchecked return values
xen/blkfront: avoid NULL blkfront_info dereference on device removal
Here is the big USB/PHY driver patches for 4.20-rc1
Lots of USB changes in here, primarily in these areas:
- typec updates and new drivers
- new PHY drivers
- dwc2 driver updates and additions (this old core keeps getting added
to new devices.)
- usbtmc major update based on the industry group coming together and
working to add new features and performance to the driver.
- USB gadget additions for new features
- USB gadget configfs updates
- chipidea driver updates
- other USB gadget updates
- USB serial driver updates
- renesas driver updates
- xhci driver updates
- other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW9LlHw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnvwCffYmMWyMG9zSOw1oSzFPl7TVN1hYAoMyJqzLg
umyLwWxC9ZWWkrpc3iD8
=ux+Y
-----END PGP SIGNATURE-----
Merge tag 'usb-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB/PHY driver patches for 4.20-rc1
Lots of USB changes in here, primarily in these areas:
- typec updates and new drivers
- new PHY drivers
- dwc2 driver updates and additions (this old core keeps getting
added to new devices.)
- usbtmc major update based on the industry group coming together and
working to add new features and performance to the driver.
- USB gadget additions for new features
- USB gadget configfs updates
- chipidea driver updates
- other USB gadget updates
- USB serial driver updates
- renesas driver updates
- xhci driver updates
- other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (229 commits)
usb: phy: ab8500: silence some uninitialized variable warnings
usb: xhci: tegra: Add genpd support
usb: xhci: tegra: Power-off power-domains on removal
usbip:vudc: BUG kmalloc-2048 (Not tainted): Poison overwritten
usbip: tools: fix atoi() on non-null terminated string
USB: misc: appledisplay: fix backlight update_status return code
phy: phy-pxa-usb: add a new driver
usb: host: add DT bindings for faraday fotg2
usb: host: ohci-at91: fix request of irq for optional gpio
usb/early: remove set but not used variable 'remain_length'
usb: typec: Fix copy/paste on typec_set_vconn_role() kerneldoc
usb: typec: tcpm: Report back negotiated PPS voltage and current
USB: core: remove set but not used variable 'udev'
usb: core: fix memory leak on port_dev_path allocation
USB: net2280: Remove ->disconnect() callback from net2280_pullup()
usb: dwc2: disable power_down on rockchip devices
usb: gadget: udc: renesas_usb3: add support for r8a77990
dt-bindings: usb: renesas_usb3: add bindings for r8a77990
usb: gadget: udc: renesas_usb3: Add r8a774a1 support
USB: serial: cypress_m8: remove set but not used variable 'iflag'
...
Drivers exposing zoned block devices have to initialize and maintain
correctness (i.e. revalidate) of the device zone bitmaps attached to
the device request queue (seq_zones_bitmap and seq_zones_wlock).
To simplify coding this, introduce a generic helper function
blk_revalidate_disk_zones() suitable for most (and likely all) cases.
This new function always update the seq_zones_bitmap and seq_zones_wlock
bitmaps as well as the queue nr_zones field when called for a disk
using a request based queue. For a disk using a BIO based queue, only
the number of zones is updated since these queues do not have
schedulers and so do not need the zone bitmaps.
With this change, the zone bitmap initialization code in sd_zbc.c can be
replaced with a call to this function in sd_zbc_read_zones(), which is
called from the disk revalidate block operation method.
A call to blk_revalidate_disk_zones() is also added to the null_blk
driver for devices created with the zoned mode enabled.
Finally, to ensure that zoned devices created with dm-linear or
dm-flakey expose the correct number of zones through sysfs, a call to
blk_revalidate_disk_zones() is added to dm_table_set_restrictions().
The zone bitmaps allocated and initialized with
blk_revalidate_disk_zones() are freed automatically from
__blk_release_queue() using the block internal function
blk_queue_free_zone_bitmaps().
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Dispatching a report zones command through the request queue is a major
pain due to the command reply payload rewriting necessary. Given that
blkdev_report_zones() is executing everything synchronously, implement
report zones as a block device file operation instead, allowing major
simplification of the code in many places.
sd, null-blk, dm-linear and dm-flakey being the only block device
drivers supporting exposing zoned block devices, these drivers are
modified to provide the device side implementation of the
report_zones() block device file operation.
For device mappers, a new report_zones() target type operation is
defined so that the upper block layer calls blkdev_report_zones() can
be propagated down to the underlying devices of the dm targets.
Implementation for this new operation is added to the dm-linear and
dm-flakey targets.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
[Damien]
* Changed method block_device argument to gendisk
* Various bug fixes and improvements
* Added support for null_blk, dm-linear and dm-flakey.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The unsigned 32 bits overflow check for the zone size value is already
done within sd_zbc_check_zones() with the test:
} else if (logical_to_sectors(sdkp->device, zone_blocks) > UINT_MAX) {
so there is no need to check again for an out of range value in
sd_zbc_read_zones(). Simplify the code and fix sd_zbc_check_zones()
error return to -EFBIG instead of -ENODEV if the zone size is too large.
Change the return type of sd_zbc_check_zones() to an int for the error
code and return the zone size (zone_blocks) through a u32 pointer to
avoid overflowing the signed 32 return value.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Handling checks of ZBC device capacity using the max_lba field of the
REPORT ZONES command reply for disks with rc_basis == 0 can be done
using the same report zones command reply used to check the "same"
field.
Avoid executing a report zones command solely to check the disk capacity
by merging sd_zbc_check_capacity() into sd_zbc_check_zone_size() and
renaming that function to sd_zbc_check_zones(). This removes a costly
execution of a full report zones command and so reduces device scan
duration at boot time as well as the duration of disk revalidate calls.
Furthermore, setting the partial report bit in the REPORT ZONES command
cdb can significantly reduce this command execution time as the device
does not have to count and report the total number of zones that could
be reported assuming a large enough reply buffer. A non-partial zone
report is necessary only for the first execution of report zones used to
check the same field value (to ensure that this value applies to all
zones of the disk). All other calls to sd_zbc_report_zones() can use a
partial report to reduce execution time.
Using a 14 TB ZBC disk, these simple changes reduce device scan time at
boot from about 3.5s down to about 900ms. Disk revalidate times are also
reduced from about 450ms down to 230ms.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the urswrz check out of sd_zbc_read_zones() and into
sd_zbc_read_zoned_characteristics() where that value is obtained (read
from the disk zoned characteristics VPD page). Since this function now
does more than simply reading the VPD page, rename it to
sd_zbc_check_zoned_characteristics().
Also fix the error message displayed when reading that VPD page fails.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is mostly updates of the usual drivers: UFS, esp_scsi, NCR5380,
qla2xxx, lpfc, libsas, hisi_sas. In addition there's a set of mostly
small updates to the target subsystem a set of conversions to the
generic DMA API, which do have some potential for issues in the older
drivers but we'll handle those as case by case fixes. A new myrs for
the DAC960/mylex raid controllers to replace the block based DAC960
which is also being removed by Jens in this merge window. Plus the
usual slew of trivial changes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCW9BQJSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishU3MAP41T8yW
UJQDCprj65pCR+9mOUWzgMvgAW/15ouK89x/7AD/XAEQZqoAgpFUbgnoZWGddZkS
LykIzSiLHP4qeDOh1TQ=
=2JMU
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual drivers: UFS, esp_scsi, NCR5380,
qla2xxx, lpfc, libsas, hisi_sas.
In addition there's a set of mostly small updates to the target
subsystem a set of conversions to the generic DMA API, which do have
some potential for issues in the older drivers but we'll handle those
as case by case fixes.
A new myrs driver for the DAC960/mylex raid controllers to replace the
block based DAC960 which is also being removed by Jens in this merge
window.
Plus the usual slew of trivial changes"
[ "myrs" stands for "MYlex Raid Scsi". Obviously. Silly of me to even
wonder. There's also a "myrb" driver, where the 'b' stands for
'block'. Truly, somebody has got mad naming skillz. - Linus ]
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (237 commits)
scsi: myrs: Fix the processor absent message in processor_show()
scsi: myrs: Fix a logical vs bitwise bug
scsi: hisi_sas: Fix NULL pointer dereference
scsi: myrs: fix build failure on 32 bit
scsi: fnic: replace gross legacy tag hack with blk-mq hack
scsi: mesh: switch to generic DMA API
scsi: ips: switch to generic DMA API
scsi: smartpqi: fully convert to the generic DMA API
scsi: vmw_pscsi: switch to generic DMA API
scsi: snic: switch to generic DMA API
scsi: qla4xxx: fully convert to the generic DMA API
scsi: qla2xxx: fully convert to the generic DMA API
scsi: qla1280: switch to generic DMA API
scsi: qedi: fully convert to the generic DMA API
scsi: qedf: fully convert to the generic DMA API
scsi: pm8001: switch to generic DMA API
scsi: nsp32: switch to generic DMA API
scsi: mvsas: fully convert to the generic DMA API
scsi: mvumi: switch to generic DMA API
scsi: mpt3sas: switch to generic DMA API
...
-----BEGIN PGP SIGNATURE-----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=58I4
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Fix ASPM link_state teardown on removal (Lukas Wunner)
- Fix misleading _OSC ASPM message (Sinan Kaya)
- Make _OSC optional for PCI (Sinan Kaya)
- Don't initialize ASPM link state when ACPI_FADT_NO_ASPM is set
(Patrick Talbert)
- Remove x86 and arm64 node-local allocation for host bridge structures
(Punit Agrawal)
- Pay attention to device-specific _PXM node values (Jonathan Cameron)
- Support new Immediate Readiness bit (Felipe Balbi)
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state
(Keith Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and
re-enumerate devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets
(Keith Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable
from cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments
(Keith Busch)
- Remove unused Netronome NFP32xx Device IDs (Jakub Kicinski)
- Use bitmap_zalloc() for dma_alias_mask (Andy Shevchenko)
- Add switch fall-through annotations (Gustavo A. R. Silva)
- Remove unused Switchtec quirk variable (Joshua Abraham)
- Fix pci.c kernel-doc warning (Randy Dunlap)
- Remove trivial PCI wrappers for DMA APIs (Christoph Hellwig)
- Add Intel GPU device IDs to spurious interrupt quirk (Bin Meng)
- Run Switchtec DMA aliasing quirk only on NTB endpoints to avoid
useless dmesg errors (Logan Gunthorpe)
- Update Switchtec NTB documentation (Wesley Yung)
- Remove redundant "default n" from Kconfig (Bartlomiej Zolnierkiewicz)
- Avoid panic when drivers enable MSI/MSI-X twice (Tonghao Zhang)
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
- Fix VMD AERSID quirk Device ID matching (Jon Derrick)
- Fix Cadence PHY handling during probe (Alan Douglas)
- Signal Cadence Endpoint interrupts via AXI region 0 instead of last
region (Alan Douglas)
- Write Cadence Endpoint MSI interrupts with 32 bits of data (Alan
Douglas)
- Remove redundant controller tests for "device_type == pci" (Rob
Herring)
- Document R-Car E3 (R8A77990) bindings (Tho Vu)
- Add device tree support for R-Car r8a7744 (Biju Das)
- Drop unused mvebu PCIe capability code (Thomas Petazzoni)
- Add shared PCI bridge emulation code (Thomas Petazzoni)
- Convert mvebu to use shared PCI bridge emulation (Thomas Petazzoni)
- Add aardvark Root Port emulation (Thomas Petazzoni)
- Support 100MHz/200MHz refclocks for i.MX6 (Lucas Stach)
- Add initial power management for i.MX7 (Leonard Crestez)
- Add PME_Turn_Off support for i.MX7 (Leonard Crestez)
- Fix qcom runtime power management error handling (Bjorn Andersson)
- Update TI dra7xx unaligned access errata workaround for host mode as
well as endpoint mode (Vignesh R)
- Fix kirin section mismatch warning (Nathan Chancellor)
- Remove iproc PAXC slot check to allow VF support (Jitendra Bhivare)
- Quirk Keystone K2G to limit MRRS to 256 (Kishon Vijay Abraham I)
- Update Keystone to use MRRS quirk for host bridge instead of open
coding (Kishon Vijay Abraham I)
- Refactor Keystone link establishment (Kishon Vijay Abraham I)
- Simplify and speed up Keystone link training (Kishon Vijay Abraham I)
- Remove unused Keystone host_init argument (Kishon Vijay Abraham I)
- Merge Keystone driver files into one (Kishon Vijay Abraham I)
- Remove redundant Keystone platform_set_drvdata() (Kishon Vijay
Abraham I)
- Rename Keystone functions for uniformity (Kishon Vijay Abraham I)
- Add Keystone device control module DT binding (Kishon Vijay Abraham
I)
- Use SYSCON API to get Keystone control module device IDs (Kishon
Vijay Abraham I)
- Clean up Keystone PHY handling (Kishon Vijay Abraham I)
- Use runtime PM APIs to enable Keystone clock (Kishon Vijay Abraham I)
- Clean up Keystone config space access checks (Kishon Vijay Abraham I)
- Get Keystone outbound window count from DT (Kishon Vijay Abraham I)
- Clean up Keystone outbound window configuration (Kishon Vijay Abraham
I)
- Clean up Keystone DBI setup (Kishon Vijay Abraham I)
- Clean up Keystone ks_pcie_link_up() (Kishon Vijay Abraham I)
- Fix Keystone IRQ status checking (Kishon Vijay Abraham I)
- Add debug messages for all Keystone errors (Kishon Vijay Abraham I)
- Clean up Keystone includes and macros (Kishon Vijay Abraham I)
- Fix Mediatek unchecked return value from devm_pci_remap_iospace()
(Gustavo A. R. Silva)
- Fix Mediatek endpoint/port matching logic (Honghui Zhang)
- Change Mediatek Root Port Class Code to PCI_CLASS_BRIDGE_PCI (Honghui
Zhang)
- Remove redundant Mediatek PM domain check (Honghui Zhang)
- Convert Mediatek to pci_host_probe() (Honghui Zhang)
- Fix Mediatek MSI enablement (Honghui Zhang)
- Add Mediatek system PM support for MT2712 and MT7622 (Honghui Zhang)
- Add Mediatek loadable module support (Honghui Zhang)
- Detach VMD resources after stopping root bus to prevent orphan
resources (Jon Derrick)
- Convert pcitest build process to that used by other tools (iio, perf,
etc) (Gustavo Pimentel)
* tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI: pcie: Remove redundant 'default n' from Kconfig
PCI: aardvark: Implement emulated root PCI bridge config space
PCI: mvebu: Convert to PCI emulated bridge config space
PCI: mvebu: Drop unused PCI express capability code
PCI: Introduce PCI bridge emulated config space common logic
PCI: vmd: Detach resources after stopping root bus
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
...
Pull networking updates from David Miller:
1) Add VF IPSEC offload support in ixgbe, from Shannon Nelson.
2) Add zero-copy AF_XDP support to i40e, from Björn Töpel.
3) All in-tree drivers are converted to {g,s}et_link_ksettings() so we
can get rid of the {g,s}et_settings ethtool callbacks, from Michal
Kubecek.
4) Add software timestamping to veth driver, from Michael Walle.
5) More work to make packet classifiers and actions lockless, from Vlad
Buslov.
6) Support sticky FDB entries in bridge, from Nikolay Aleksandrov.
7) Add ipv6 version of IP_MULTICAST_ALL sockopt, from Andre Naujoks.
8) Support batching of XDP buffers in vhost_net, from Jason Wang.
9) Add flow dissector BPF hook, from Petar Penkov.
10) i40e vf --> generic iavf conversion, from Jesse Brandeburg.
11) Add NLA_REJECT netlink attribute policy type, to signal when users
provide attributes in situations which don't make sense. From
Johannes Berg.
12) Switch TCP and fair-queue scheduler over to earliest departure time
model. From Eric Dumazet.
13) Improve guest receive performance by doing rx busy polling in tx
path of vhost networking driver, from Tonghao Zhang.
14) Add per-cgroup local storage to bpf
15) Add reference tracking to BPF, from Joe Stringer. The verifier can
now make sure that references taken to objects are properly released
by the program.
16) Support in-place encryption in TLS, from Vakul Garg.
17) Add new taprio packet scheduler, from Vinicius Costa Gomes.
18) Lots of selftests additions, too numerous to mention one by one here
but all of which are very much appreciated.
19) Support offloading of eBPF programs containing BPF to BPF calls in
nfp driver, frm Quentin Monnet.
20) Move dpaa2_ptp driver out of staging, from Yangbo Lu.
21) Lots of u32 classifier cleanups and simplifications, from Al Viro.
22) Add new strict versions of netlink message parsers, and enable them
for some situations. From David Ahern.
23) Evict neighbour entries on carrier down, also from David Ahern.
24) Support BPF sk_msg verdict programs with kTLS, from Daniel Borkmann
and John Fastabend.
25) Add support for filtering route dumps, from David Ahern.
26) New igc Intel driver for 2.5G parts, from Sasha Neftin et al.
27) Allow vxlan enslavement to bridges in mlxsw driver, from Ido
Schimmel.
28) Add queue and stack map types to eBPF, from Mauricio Vasquez B.
29) Add back byte-queue-limit support to r8169, with all the bug fixes
in other areas of the driver it works now! From Florian Westphal and
Heiner Kallweit.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2147 commits)
tcp: add tcp_reset_xmit_timer() helper
qed: Fix static checker warning
Revert "be2net: remove desc field from be_eq_obj"
Revert "net: simplify sock_poll_wait"
net: socionext: Reset tx queue in ndo_stop
net: socionext: Add dummy PHY register read in phy_write()
net: socionext: Stop PHY before resetting netsec
net: stmmac: Set OWN bit for jumbo frames
arm64: dts: stratix10: Support Ethernet Jumbo frame
tls: Add maintainers
net: ethernet: ti: cpsw: unsync mcast entries while switch promisc mode
octeontx2-af: Support for NIXLF's UCAST/PROMISC/ALLMULTI modes
octeontx2-af: Support for setting MAC address
octeontx2-af: Support for changing RSS algorithm
octeontx2-af: NIX Rx flowkey configuration for RSS
octeontx2-af: Install ucast and bcast pkt forwarding rules
octeontx2-af: Add LMAC channel info to NIXLF_ALLOC response
octeontx2-af: NPC MCAM and LDATA extract minimal configuration
octeontx2-af: Enable packet length and csum validation
octeontx2-af: Support for VTAG strip and capture
...
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/mvsas/mv_sas.c: In function 'mvs_work_queue':
drivers/scsi/mvsas/mv_sas.c:1909:31: warning:
variable 'id' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit
20b09c2992 ("[SCSI] mvsas: add support for 94xx; layout change; bug fixes")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move a debug statement from qlafx00_error_entry() into its caller. Remove
one unused argument from that function. This patch does not change the
behavior of the qla2xxx driver.
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Only one of the two code paths in qlafx00_ioctl_iosb_entry() initializes
the variable 'res'. Make sure that 'res' is initialized before
sp->done(sp, res) is called.
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality.
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modify the unlock statement such that it becomes easier for static
analyzers to analyze it. This patch does not change any functionality.
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the compiler complains about missing declarations
when building with W=1.
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that complaints about kernel-doc headers are reported
when building with W=1.
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that the compiler complains about missing fall-through
annotations when building with W=1.
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clang warns a few times:
drivers/scsi/3w-sas.c:386:11: warning: implicit conversion from 'int' to
'char' changes value from 128 to -128 [-Wconstant-conversion]
cdb[4] = TW_ALLOCATION_LENGTH; /* allocation length */
~ ^~~~~~~~~~~~~~~~~~~~
Update cdb's type to unsigned char, which matches the type of the cdb
member in struct TW_Command_Apache.
Link: https://github.com/ClangBuiltLinux/linux/issues/158
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace dma_pool_alloc + memset with dma_pool_zalloc.
Signed-off-by: Sabyasachi Gupta <sabyasachi.linux@gmail.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull pcmcia fixes from Dominik Brodowski:
"These are just a few odd fixes and improvements to the PCMCIA core and
to a few PCMCIA device drivers"
* 'pcmcia-next' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux:
pcmcia: Implement CLKRUN protocol disabling for Ricoh bridges
pcmcia: pcmcia_resource: Replace mdelay() with msleep()
pcmcia: add error handling for pcmcia_enable_device in qlogic_stub
char: pcmcia: cm4000_cs: Replace mdelay with usleep_range in set_protocol
pcmcia: Use module_pcmcia_driver for scsi drivers
pcmcia: remove KERN_INFO level from debug message
-----BEGIN PGP SIGNATURE-----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=LRTT
-----END PGP SIGNATURE-----
Merge tag 'for-4.20/block-20181021' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"This is the main pull request for block changes for 4.20. This
contains:
- Series enabling runtime PM for blk-mq (Bart).
- Two pull requests from Christoph for NVMe, with items such as;
- Better AEN tracking
- Multipath improvements
- RDMA fixes
- Rework of FC for target removal
- Fixes for issues identified by static checkers
- Fabric cleanups, as prep for TCP transport
- Various cleanups and bug fixes
- Block merging cleanups (Christoph)
- Conversion of drivers to generic DMA mapping API (Christoph)
- Series fixing ref count issues with blkcg (Dennis)
- Series improving BFQ heuristics (Paolo, et al)
- Series improving heuristics for the Kyber IO scheduler (Omar)
- Removal of dangerous bio_rewind_iter() API (Ming)
- Apply single queue IPI redirection logic to blk-mq (Ming)
- Set of fixes and improvements for bcache (Coly et al)
- Series closing a hotplug race with sysfs group attributes (Hannes)
- Set of patches for lightnvm:
- pblk trace support (Hans)
- SPDX license header update (Javier)
- Tons of refactoring patches to cleanly abstract the 1.2 and 2.0
specs behind a common core interface. (Javier, Matias)
- Enable pblk to use a common interface to retrieve chunk metadata
(Matias)
- Bug fixes (Various)
- Set of fixes and updates to the blk IO latency target (Josef)
- blk-mq queue number updates fixes (Jianchao)
- Convert a bunch of drivers from the old legacy IO interface to
blk-mq. This will conclude with the removal of the legacy IO
interface itself in 4.21, with the rest of the drivers (me, Omar)
- Removal of the DAC960 driver. The SCSI tree will introduce two
replacement drivers for this (Hannes)"
* tag 'for-4.20/block-20181021' of git://git.kernel.dk/linux-block: (204 commits)
block: setup bounce bio_sets properly
blkcg: reassociate bios when make_request() is called recursively
blkcg: fix edge case for blk_get_rl() under memory pressure
nvme-fabrics: move controller options matching to fabrics
nvme-rdma: always have a valid trsvcid
mtip32xx: fully switch to the generic DMA API
rsxx: switch to the generic DMA API
umem: switch to the generic DMA API
sx8: switch to the generic DMA API
sx8: remove dead IF_64BIT_DMA_IS_POSSIBLE code
skd: switch to the generic DMA API
ubd: remove use of blk_rq_map_sg
nvme-pci: remove duplicate check
drivers/block: Remove DAC960 driver
nvme-pci: fix hot removal during error handling
nvmet-fcloop: suppress a compiler warning
nvme-core: make implicit seed truncation explicit
nvmet-fc: fix kernel-doc headers
nvme-fc: rework the request initialization code
nvme-fc: introduce struct nvme_fcp_op_w_sgl
...
If both processors are absent then it's supposed to print that, but
instead we print that just the second processor is absent.
Fixes: 7726618639 ("scsi: myrs: Add Mylex RAID controller (SCSI interface)")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The || was supposed to be |. The original code just sets ->result to 1.
Fixes: 7726618639 ("scsi: myrs: Add Mylex RAID controller (SCSI interface)")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a NULL pointer dereference in case *slot* happens to be NULL at
lines 1053 and 1878:
struct hisi_sas_cq *cq =
&hisi_hba->cq[slot->dlvry_queue];
Notice that *slot* is being NULL checked at lines 1057 and 1881:
if (slot), which implies it may be NULL.
Fix this by placing the declaration and definition of variable cq, which
contains the pointer dereference slot->dlvry_queue, after slot has been
properly NULL checked.
Addresses-Coverity-ID: 1474515 ("Dereference before null check")
Addresses-Coverity-ID: 1474520 ("Dereference before null check")
Fixes: 584f53fe5f ("scsi: hisi_sas: Fix the race between IO completion and timeout for SMP/internal IO")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For 32 bit versions we have to be careful about divisions of 64 bit
quantities so use do_div() instead of a direct division. This fixes a
warning about _uldivmod being undefined in certain configurations
Fixes: 7726618639 ("scsi: myrs: Add Mylex RAID controller")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Would be nice to fix up the SCSI midlayer instead, but this will do for
now.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Satish Kharat <satishkh@cisco.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is currently using an odd mix of legacy PCI DMA API and
generic DMA API calls, switch it over to the generic API entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Don Brace <don.brace@microchip.com>
Acked-by: Don Brace <don.brace@microchip.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is currently using an odd mix of legacy PCI DMA API and
generic DMA API calls, switch it over to the generic API entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is currently using an odd mix of legacy PCI DMA API and
generic DMA API calls, switch it over to the generic API entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is currently using an odd mix of legacy PCI DMA API and
generic DMA API calls, switch it over to the generic API entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is currently using an odd mix of legacy PCI DMA API and
generic DMA API calls, switch it over to the generic API entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Chad Dupuis <chad.dupuis@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is currently using an odd mix of legacy PCI DMA API and
generic DMA API calls, switch it over to the generic API entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Also reuse an existing helper (after fixing the error return) to set the
DMA mask instead of having three copies of the code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Also simplify setting the DMA mask a bit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Don Brace <don.brace@microchip.com>
Acked-by: Don Brace <don.brace@microchip.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is currently using an odd mix of legacy PCI DMA API and
generic DMA API calls, switch it over to the generic API entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Adam Radford <aradford@gmail.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is currently using an odd mix of legacy PCI DMA API and
generic DMA API calls, switch it over to the generic API entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Adam Radford <aradford@gmail.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is currently using an odd mix of legacy PCI DMA API and
generic DMA API calls, switch it over to the generic API entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Adam Radford <aradford@gmail.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is currently using an odd mix of legacy PCI DMA API and
generic DMA API calls, switch it over to the generic API entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid function calls in the inner PIO loops. On a Centris 660av this
improves throughput for sequential read transfers by about 40% and
sequential write by about 10%.
Unfortunately it is not possible to have methods like .esp_write8 placed
inline so this is always going to be slow, even with LTO.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As a temporary measure, the code to implement PIO transfers was
duplicated in zorro_esp and mac_esp. Now that it has stabilized move the
common code into the core driver but don't build it unless needed.
This replaces the inline assembler with more portable writesb() calls.
Optimizing the m68k writesb() implementation is a separate patch.
[mkp: applied by hand]
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The concept of a 'slow command' as it appears in esp_scsi is confusing
because it could refer to an ESP command or a SCSI command. It turns out
that it refers to a particular ESP select command which the driver also
tracks as 'ESP_SELECT_MSGOUT'. For readability, it is better to use the
terminology from the datasheets.
The global ESP_FLAG_DOING_SLOWCMD flag is redundant anyway, as it can be
inferred from esp->select_state. Remove the ESP_FLAG_DOING_SLOWCMD cruft
and just use a boolean local variable.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A SCSI device is not granted disconnect privilege by an esp_scsi host
unless that device has its simple_tags flag set. However, a device may
support disconnect/reselect and not support command queueing. Allow such
devices to disconnect and thereby improve bus utilization.
Drop the redundant 'lp' check. The mid-layer invokes .slave_alloc and
.slave_destroy in such a way that we may rely on scmd->device->hostdata
for as long as scmd belongs to the low-level driver.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a target disconnects during a PIO data transfer the command may fail
when the target reconnects:
scsi host1: DMA length is zero!
scsi host1: cur adr[04380000] len[00000000]
The scsi bus is then reset. This happens because the residual reached
zero before the transfer was completed.
The usual residual calculation relies on the Transfer Count registers.
That works for DMA transfers but not for PIO transfers. Fix the problem
by storing the PIO transfer residual and using that to correctly
calculate bytes_sent.
Fixes: 6fe07aaffb ("[SCSI] m68k: new mac_esp scsi driver")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The core driver, esp_scsi, does not use the ESP_CONFIG2_FENAB bit, so the
chip's Transfer Counter register is only 16 bits wide (not 24). A larger
transfer cannot work and will theoretically result in a failed command
and a "DMA length is zero" error.
Fixes: 3109e5ae03 ("scsi: zorro_esp: New driver for Amiga Zorro NCR53C9x boards")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Convert the driver from the legacy pci_* DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We need to transfer device ownership to the CPU before we can manipulate
the mapped data.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We can't just transfer ownership to the CPU and then unmap, as this will
break with swiotlb.
Instead unmap the command and sense buffer a little earlier in the I/O
completion handler and get rid of the pci_dma_sync_sg_for_cpu call
entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the list wrappers, including the pointless list iteration before
deletion.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support for the Mylex DAC960 RAID controller,
supporting the newer, SCSI-based interface. The driver is a
re-implementation of the original DAC960 driver.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support for the Mylex DAC960 RAID controller,
supporting the older, block-based interface only. The driver is a
re-implementation of the original DAC960 driver.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
drivers/scsi/advansys.c: In function 'adv_isr_callback':
drivers/scsi/advansys.c:5952:6: warning:
variable 'srb_tag' set but not used [-Wunused-but-set-variable]
It never used since introduction in
commit 9c17c62aed ("advansys: use shared host tag map for command lookup")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This message floods the log when enabling mask 0x7 for
/proc/sys/dev/scsi/logging_level:
xxxxxxxx kernel: scsi_block_when_processing_errors: rtn: 1
It's not needed and makes tracing just scsi_eh* messages way too
verbose so get rid of it.
[mkp: mangled patch, applied by hand]
Signed-off-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Chad Dupuis <chad.dupuis@cavium.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is currently a bug with the driver where there is never a call to
target_sess_cmd_list_set_waiting(), it only called
target_wait_for_sess_cmd(), which basically means that the sess_wait_list
would always be empty.
Thus, list_empty(&sess->sess_wait_list) = true,
(eg: no se_cmd I/O is quiesced, because no se_cmd in sess_wait_list),
since commit 712db3eb2c ("scsi: ibmvscsis: Properly deregister
target sessions") in 4.9.y code.
ibmvscsi_tgt does not remove the I_T Nexus when a VM is active so we can
fix this issue by removing the call to target_wait_for_sess_cmd()
altogether.
Signed-off-by: Bryant G. Ly <bly@catalogicsoftware.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With commit 10e5e37581 ("scsi: ufs: Add clock ungating to a separate
workqueue"), clock gating work was moved to a separate work queue with
WQ_MEM_RECLAIM set, since clock gating could occur from a memory reclaim
context. Unfortunately, clk_gating.gate_work was left queued via
schedule_delayed_work, which is a system workqueue that does not have
WQ_MEM_RECLAIM set. Because ufshcd_ungate_work attempts to cancel
gate_work, the following warning appears:
[ 14.174170] workqueue: WQ_MEM_RECLAIM ufs_clk_gating_0:ufshcd_ungate_work is flushing !WQ_MEM_RECLAIM events:ufshcd_gate_work
[ 14.174179] WARNING: CPU: 4 PID: 173 at kernel/workqueue.c:2440 check_flush_dependency+0x110/0x118
[ 14.205725] CPU: 4 PID: 173 Comm: kworker/u16:3 Not tainted 4.14.68 #1
[ 14.212437] Hardware name: Google Cheza (rev1) (DT)
[ 14.217459] Workqueue: ufs_clk_gating_0 ufshcd_ungate_work
[ 14.223107] task: ffffffc0f6a40080 task.stack: ffffff800a490000
[ 14.229195] PC is at check_flush_dependency+0x110/0x118
[ 14.234569] LR is at check_flush_dependency+0x110/0x118
[ 14.239944] pc : [<ffffff80080cad14>] lr : [<ffffff80080cad14>] pstate: 60c001c9
[ 14.333050] Call trace:
[ 14.427767] [<ffffff80080cad14>] check_flush_dependency+0x110/0x118
[ 14.434219] [<ffffff80080cafec>] start_flush_work+0xac/0x1fc
[ 14.440046] [<ffffff80080caeec>] flush_work+0x40/0x94
[ 14.445246] [<ffffff80080cb288>] __cancel_work_timer+0x11c/0x1b8
[ 14.451433] [<ffffff80080cb4b8>] cancel_delayed_work_sync+0x20/0x30
[ 14.457886] [<ffffff80085b9294>] ufshcd_ungate_work+0x24/0xd0
[ 14.463800] [<ffffff80080cfb04>] process_one_work+0x32c/0x690
[ 14.469713] [<ffffff80080d0154>] worker_thread+0x218/0x338
[ 14.475361] [<ffffff80080d527c>] kthread+0x120/0x130
[ 14.480470] [<ffffff8008084814>] ret_from_fork+0x10/0x18
The simple solution is to put the gate_work on the same WQ_MEM_RECLAIM
work queue as the ungate_work.
Fixes: 10e5e37581 ("scsi: ufs: Add clock ungating to a separate workqueue")
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/lpfc/lpfc_debugfs.c: In function 'lpfc_debugfs_nodelist_data':
drivers/scsi/lpfc/lpfc_debugfs.c:553:29: warning:
variable 'tgtp' set but not used [-Wunused-but-set-variable]
It never used since 2b65e18202 ("scsi: lpfc: NVME Target: Add debugfs support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114988 ("Missing break in switch")
Addresses-Coverity-ID: 114989 ("Missing break in switch")
Addresses-Coverity-ID: 114990 ("Missing break in switch")
Addresses-Coverity-ID: 114991 ("Missing break in switch")
Addresses-Coverity-ID: 114992 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clang warns when one enumerated type is implicitly converted to another.
drivers/scsi/iscsi_tcp.c:803:15: warning: implicit conversion from
enumeration type 'enum iscsi_host_param' to different enumeration type
'enum iscsi_param' [-Wenum-conversion]
&addr, param, buf);
^~~~~
1 warning generated.
iscsi_conn_get_addr_param handles ISCSI_HOST_PARAM_IPADDRESS just fine
so add an explicit cast to iscsi_param to make it clear to Clang that
this is expected behavior.
Link: https://github.com/ClangBuiltLinux/linux/issues/153
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/lpfc/lpfc_hbadisc.c: In function 'lpfc_free_tx':
drivers/scsi/lpfc/lpfc_hbadisc.c:5431:19: warning:
variable 'psli' set but not used [-Wunused-but-set-variable]
Since commit 895427bd01 ("scsi: lpfc: NVME Initiator: Base modifications")
'psli' is not used any more.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clang warns when one enumerated type is implicitly converted to another.
drivers/scsi/bfa/bfa_fcs_lport.c:379:26: warning: implicit conversion
from enumeration type 'enum bfa_lport_aen_event' to different
enumeration type 'enum bfa_ioc_aen_event' [-Wenum-conversion]
BFA_AEN_CAT_LPORT, event);
^~~~~
The root cause of these warnings is the bfad_im_post_vendor_event
function, which expects a value from enum bfa_ioc_aen_event but there
are multiple instances of values from enums bfa_port_aen_event,
bfa_audit_aen_event, and bfa_lport_aen_event being used in this
function.
Given that this doesn't appear to be a problem since cat helps with
differentiating the events, just change evt's type to int so that no
conversion needs to happen and Clang won't warn. Update aen_type's type
in bfa_aen_entry_s as members that hold enumerated types should be int.
Link: https://github.com/ClangBuiltLinux/linux/issues/147
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clang warns when an enumerated type is implicitly converted to another.
drivers/scsi/isci/request.c:3476:13: warning: implicit conversion from
enumeration type 'enum sci_task_status' to different enumeration type
'enum sci_status' [-Wenum-conversion]
status = sci_controller_start_task(ihost,
~ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/isci/host.c:2744:10: warning: implicit conversion from
enumeration type 'enum sci_status' to different enumeration type 'enum
sci_task_status' [-Wenum-conversion]
return SCI_SUCCESS;
~~~~~~ ^~~~~~~~~~~
drivers/scsi/isci/host.c:2753:9: warning: implicit conversion from
enumeration type 'enum sci_status' to different enumeration type 'enum
sci_task_status' [-Wenum-conversion]
return status;
~~~~~~ ^~~~~~
Avoid all of these implicit conversion by just making
sci_controller_start_task use sci_status. This silences
Clang and has no functional change since sci_task_status
has all of its values mapped to something in sci_status.
Link: https://github.com/ClangBuiltLinux/linux/issues/153
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clang warns when one enumerated type is implicitly converted to another.
drivers/scsi/isci/request.c:1629:13: warning: implicit conversion from
enumeration type 'enum sci_io_status' to different enumeration type
'enum sci_status' [-Wenum-conversion]
status = SCI_IO_FAILURE_RESPONSE_VALID;
~ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/isci/request.c:1631:12: warning: implicit conversion from
enumeration type 'enum sci_io_status' to different enumeration type
'enum sci_status' [-Wenum-conversion]
status = SCI_IO_FAILURE_RESPONSE_VALID;
~ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
status is of type sci_status but SCI_IO_FAILURE_RESPONSE_VALID is of
type sci_io_status. Use SCI_FAILURE_IO_RESPONSE_VALID, which is from
sci_status and has SCI_IO_FAILURE_RESPONSE_VALID's exact value since
that is what SCI_IO_FAILURE_RESPONSE_VALID is mapped to in the isci.h
file.
Link: https://github.com/ClangBuiltLinux/linux/issues/153
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/lpfc/lpfc_sli.c: In function 'lpfc_sli4_sp_handle_rcqe':
drivers/scsi/lpfc/lpfc_sli.c:13430:26: warning:
variable 'fc_hdr' set but not used [-Wunused-but-set-variable]
drivers/scsi/lpfc/lpfc_sli.c: In function 'lpfc_cq_create':
drivers/scsi/lpfc/lpfc_sli.c:14852:11: warning:
variable 'hw_page_size' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add IEEE and CEE DCBX support for iSCSI connections.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/megaraid/megaraid_mbox.c: In function 'megaraid_reset_handler':
drivers/scsi/megaraid/megaraid_mbox.c:2580:7: warning:
variable 'recovering' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_mbox.c: In function 'mbox_post_sync_cmd':
drivers/scsi/megaraid/megaraid_mbox.c:2728:12: warning:
variable 'mbox64' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_mbox.c: In function 'megaraid_mbox_support_random_del':
drivers/scsi/megaraid/megaraid_mbox.c:3138:11: warning:
variable 'mbox' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_mbox.c: In function 'megaraid_mbox_flush_cache':
drivers/scsi/megaraid/megaraid_mbox.c:3266:10: warning:
variable 'mbox' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_mbox.c: In function 'megaraid_mbox_fire_sync_cmd':
drivers/scsi/megaraid/megaraid_mbox.c:3302:12: warning:
variable 'mbox64' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_mbox.c: In function 'gather_hbainfo':
drivers/scsi/megaraid/megaraid_mbox.c:3797:10: warning:
variable 'dmajor' set but not used [-Wunused-but-set-variable]
[mkp: applied by hand due to conflict with hch's DMA cleanup]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clang generates a warning when it sees a logical not followed by a
conditional operator like ==, >, or < because it thinks that the logical
not should be applied to the whole statement:
drivers/scsi/qla2xxx/qla_nx.c:3702:7: warning: logical not is only
applied to the left hand side of this comparison
[-Wlogical-not-parentheses]
if (!qla2x00_eh_wait_for_pending_commands(vha, 0, 0,
^
drivers/scsi/qla2xxx/qla_nx.c:3702:7: note: add parentheses after the
'!' to evaluate the comparison first
if (!qla2x00_eh_wait_for_pending_commands(vha, 0, 0,
^
(
drivers/scsi/qla2xxx/qla_nx.c:3702:7: note: add parentheses around left
hand side expression to silence this warning
if (!qla2x00_eh_wait_for_pending_commands(vha, 0, 0,
^
(
1 warning generated.
It assumes the author might have made a mistake in their logic:
if (!a == b) -> if (!(a == b))
Sometimes that is the case; other times, it's just a super convoluted
way of saying 'if (a)' when b = 0:
if (!1 == 0) -> if (0 == 0) -> if (true)
Alternatively:
if (!1 == 0) -> if (!!1) -> if (1)
Simplify this comparison so that Clang doesn't complain.
Link: https://github.com/ClangBuiltLinux/linux/issues/80
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clang warns when a variable is assigned to itself.
drivers/scsi/bfa/bfa_fcbuild.c:199:6: warning: explicitly assigning
value of variable of type 'int' to itself [-Wself-assign]
len = len;
~~~ ^ ~~~
drivers/scsi/bfa/bfa_fcbuild.c:838:6: warning: explicitly assigning
value of variable of type 'int' to itself [-Wself-assign]
len = len;
~~~ ^ ~~~
drivers/scsi/bfa/bfa_fcbuild.c:917:6: warning: explicitly assigning
value of variable of type 'int' to itself [-Wself-assign]
len = len;
~~~ ^ ~~~
drivers/scsi/bfa/bfa_fcbuild.c:981:6: warning: explicitly assigning
value of variable of type 'int' to itself [-Wself-assign]
len = len;
~~~ ^ ~~~
drivers/scsi/bfa/bfa_fcbuild.c:1008:6: warning: explicitly assigning
value of variable of type 'int' to itself [-Wself-assign]
len = len;
~~~ ^ ~~~
5 warnings generated.
This construct is usually used to avoid unused variable warnings, which
I assume is the case here. -Wunused-parameter is hidden behind -Wextra
with GCC 4.6, which is the minimum version to compile the kernel as of
commit cafa0010cd ("Raise the minimum required gcc version to 4.6").
However, upon further inspection, these functions aren't actually used
anywhere; they're just defined. Rather than just removing the self
assignments, remove all of this dead code.
Link: https://github.com/ClangBuiltLinux/linux/issues/148
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clang warns when a variable is assigned to itself.
drivers/scsi/qla2xxx/qla_mbx.c:1514:4: warning: explicitly assigning
value of variable of type 'uint64_t' (aka 'unsigned long long') to
itself [-Wself-assign]
l = l;
~ ^ ~
1 warning generated.
This construct is usually used to avoid unused variable warnings, which
I assume is the case here. -Wunused-parameter is hidden behind -Wextra
with GCC 4.6, which is the minimum version to compile the kernel as of
commit cafa0010cd ("Raise the minimum required gcc version to 4.6").
Just remove this line to silence Clang.
Link: https://github.com/ClangBuiltLinux/linux/issues/83
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/arcmsr/arcmsr_hba.c: In function 'arcmsr_drain_donequeue':
drivers/scsi/arcmsr/arcmsr_hba.c:1320:10: warning:
variable 'lun' set but not used [-Wunused-but-set-variable]
drivers/scsi/arcmsr/arcmsr_hba.c:1320:6: warning:
variable 'id' set but not used [-Wunused-but-set-variable]
Never used since introduction in commit ae52e7f09f ("arcmsr: Support 1024 scatter-gather list entries and improve AP while FW trapped and behaviors of EHs").
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In megasas_mgmt_compat_ioctl_fw(), to handle the structure
compat_megasas_iocpacket 'cioc', a user-space structure megasas_iocpacket
'ioc' is allocated before megasas_mgmt_ioctl_fw() is invoked to handle
the packet. Since the two data structures have different fields, the data
is copied from 'cioc' to 'ioc' field by field. In the copy process,
'sense_ptr' is prepared if the field 'sense_len' is not null, because it
will be used in megasas_mgmt_ioctl_fw(). To prepare 'sense_ptr', the
user-space data 'ioc->sense_off' and 'cioc->sense_off' are copied and
saved to kernel-space variables 'local_sense_off' and 'user_sense_off'
respectively. Given that 'ioc->sense_off' is also copied from
'cioc->sense_off', 'local_sense_off' and 'user_sense_off' should have the
same value. However, 'cioc' is in the user space and a malicious user can
race to change the value of 'cioc->sense_off' after it is copied to
'ioc->sense_off' but before it is copied to 'user_sense_off'. By doing
so, the attacker can inject different values into 'local_sense_off' and
'user_sense_off'. This can cause undefined behavior in the following
execution, because the two variables are supposed to be same.
This patch enforces a check on the two kernel variables 'local_sense_off'
and 'user_sense_off' to make sure they are the same after the copy. In
case they are not, an error code EINVAL will be returned.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to spelling mistake in beiscsi_log message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to spelling mistake in lpfc_printf_log message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently a spin_unlock_irqrestore() call is missing on the error path,
so add it.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We just need to free the request here. Additionally, this is currently
wrong for a queue that's using MQ currently, it'll crash.
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is currently wrong since it isn't dependent on if we're using mq or
not. At least now it'll be correct when we force mq.
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add missing break statement in order to prevent the code from falling
through to case TEST_UNIT_READY.
Addresses-Coverity-ID: 1357338 ("Missing break in switch")
Suggested-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update registers as follows:
- Default value of AIP timer is 1ms, and it is easy for some expanders to
cause IO error. Change the value to max value 65ms to avoid IO error for
those expanders.
- A CQ completion will be reported by HW when 4 CQs have occurred or the
aging timer expires, whichever happens first. Sor serial IO scenario, it
will still wait 8us for every IO before it is reported. So in the
situation, the performance is poor. So to improve it, change the limit
time to the least value.
For other scenario, it does little affect to the performance.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we use the IPTT defined in LLDD to identify IOs. Actually for
IOs which are from the block layer, they have tags to identify them. So
for those IOs, use tag of the block layer directly, and for IOs which is
not from the block layer (such as internal IOs from libsas/LLDD), reserve
96 IPTTs for them.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The interrupts of ent72 and ent74 are not processed by PCIe AER handling,
so we need to unmask the interrupts and process them first in the driver.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an SSP/SMP IO times out, it may be actually in reality be
simultaneously processing completion of the slot in
slot_complete_vx_hw().
Then if the slot is freed in slot_complete_vx_hw() (this IPTT is freed
and it may be re-used by other slot), and we may abort the wrong slot in
hisi_sas_abort_task().
So to solve the issue, free the slot after the check of
SAS_TASK_STATE_ABORTED in slot_complete_vx_hw().
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If SMP/internal IO times out, we will possibly free the task immediately.
However if the IO actually completes at the same time, the IO completion
may refer to task which has been freed.
So to solve the issue, flush the tasklet to finish IO completion before
free'ing slot/task.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In evaluating hisi_hba, the sas_port may be NULL, so for safety relocate
the the check to value possible NULL deference.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
At directly attached situation, if the user modifies the sysfs interface
of maximum_linkrate and minimum_linkrate to renegotiate the linkrate
between SAS controller and target, the value of both files mentioned
above should have change to user setting after renegotiate is over, but
it remains unchanged.
To fix this bug, maximum_linkrate and minimum_linkrate will be directly
fed back to relevant sas_phy structure.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When we fail to analyse the payload of a PRLI response we should reset
the state machine to retry the PRLI; eventually we will be getting a
proper frame. Not doing so will result in a stuck state machine and the
port never to be presented to the systsm.
Suggested-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <arun.easi@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We should not assume the payload of a PRLI or PLOGI respons is always
present.
Signed-off-by: Thomas Abraham <tabraham@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Arun Easi <arun.easi@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When an RSCN gets delayed (or not being sent at all), the transport class
will detect an error, EH kicks in, and eventually will be setting the
device to offline. If we receive an RSCN after that, the device will
stay in 'offline'. This patch allows for an 'offline' to 'blocked'
transition, thereby allowing the device to become active again.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The dma_addr_t member is unused ever since we switched the SCSI
layer to send down single-segement command using a scatterlist
as well many years ago.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Except for the mac_esp driver, which uses PIO or pseudo DMA, all drivers
share the same dma mapping calls. Move the dma mapping into the core
code using the scsi_dma_map / scsi_dma_unmap helpers, with a special
identify mapping variant triggered off a new ESP_FLAG_NO_DMA_MAP flag
for mac_esp.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We can simplify use esp->dev now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
esp->dev is a void pointer that points either to a struct device, or a
struct platform_device. As we can easily get from the device to the
platform_device if needed change it to always point to a struct device
and properly type the pointer to avoid errors.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
esp_sbus_map_command_block is called straight from the probe routine
without any locks held, so we can safely use GFP_KERNEL here.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove usage of the legacy PCI DMA API. To make this easier we also
store a struct device instead of pci_dev in the dev field of struct
esp.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Per Qcom's UFS host controller HW design, the UFS Tx lane1 clock could be
muxed with Tx lane0 clock, hence keep Tx lane1 clock optional by ignoring
it if it is not provided in device tree. This change also performs some
cleanup to lanes per direction checks when enable/disable lane clocks
just for symmetry.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
dma_alloc_coherent allocates memory that can be used by the cpu and the
device at the same time, calls to pci_dma_sync_* are not required, and in
fact actively harmful on some architectures like arm.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The dma_map_sg / dma_unmap_sg APIs called from scsi_dma_map /
scsi_dma_unmap already transfer memory ownership to the device or cpu
respectively. Adding additional calls to pci_dma_sync_sg_* will in fact
lead to data corruption if we end up using swiotlb for some reason.
Also remove the now pointless megaraid_mbox_sync_scb function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are extraneous parantheses that are causing clang to produce a
warning so remove these.
Clean up 3 clang warnings:
equality comparison with extraneous parentheses [-Wparentheses-equality]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make ufshcd_send_uic_cmd() public for that.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <Bart.VanAssche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Do that for the currently supported UPIUs: query, nop out, and task
management.
We do not support UPIU of type scsi command yet, while we are using the
job's request and reply pointers to hold the payload. We will look into
it in later patches. We might need to elaborate the raw upiu api for
that.
We also still not supporting uic commands: For first phase, we plan to
use the existing api, and send only uic commands that are already
supported. Anyway, all that will come in the next patch.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <Bart.VanAssche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The UFS host software uses a combination of a host register set and
Transfer Request Descriptors in system memory to communicate with host
controller hardware. In its mmio space, a separate places are assigned
to UTP Transfer Request Descriptor ("utrd") list, and to UTP Task
Management Request Descriptor ("utmrd") list.
The provided API supports utrd-typed requests: nop out and device
management commands. It also supports utmrd-type requests:
task management requests. Other UPIU types are not supported for now.
We utilize the already existing code for tag and task work queues.
That is, all utrd-typed UPIUs are "disguised" as device management
commands. Similarly, the utmrd-typed UPUIs uses the task management
infrastructure.
It is up to the caller to fill the upiu request properly, as it will be
copied without any further input validations.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <Bart.VanAssche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the structure size in pointer arithmetic instead of an opaque 32
bytes for the over-allocation of descriptors.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For now, just provide an API to allocate and remove ufs-bsg node. We
will use this framework to manage ufs devices by sending UPIU
transactions.
For the time being, implements an empty bsg_request() - will add some
more functionality in coming patches.
Nonetheless, we reveal here the protocol we are planning to use: UFS
Transport Protocol Transactions. UFS transactions consist of packets
called UFS Protocol Information Units (UPIU).
There are UPIU’s defined for UFS SCSI commands, responses, data in and
data out, task management, utility functions, vendor functions,
transaction synchronization and control, and more.
By using UPIUs, we get access to the most fine-grained internals of this
protocol, and able to communicate with the device in ways, that are
sometimes beyond the capacity of the ufs driver.
Moreover and as a result, our core structure - ufs_bsg_node has a pretty
lean structure: using upiu transactions that contains the outmost
detailed info, so we don't really need complex constructs to support it.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <Bart.VanAssche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
in preparation to send UPIU requests via bsg.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a helper that takes a utp_task_req_desc and issues it, which will
be useful for UFS bsg support. Rewrite ufshcd_issue_tm_cmd0x to use
this new helper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the pointless task_req_upiu and task_rsp_upiu indirections,
which are __le32 arrays always cast to given structures and just add
the members directly. Also clean up variables names in use in the
callers a bit to make the code more readable.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lockdep_assert_held() is better suited to checking locking requirements, since
it won't get confused when someone else holds the lock. This is also a step
towards possibly removing spin_is_locked().
Signed-off-by: Lance Roy <ldr709@gmail.com>
Cc: Karan Tilak Kumar <kartilak@cisco.com>
Cc: Sesidhar Baddela <sebaddel@cisco.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: <linux-scsi@vger.kernel.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clang warns when multiple pairs of parentheses are used for a single
conditional statement.
drivers/scsi/mpt3sas/mpt3sas_base.c:535:11: warning: equality comparison
with extraneous parentheses [-Wparentheses-equality]
if ((ioc == NULL))
~~~~^~~~~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:535:11: note: remove extraneous
parentheses around the comparison to silence this warning
if ((ioc == NULL))
~ ^ ~
drivers/scsi/mpt3sas/mpt3sas_base.c:535:11: note: use '=' to turn this
equality comparison into an assignment
if ((ioc == NULL))
^~
=
drivers/scsi/mpt3sas/mpt3sas_base.c:539:12: warning: equality comparison
with extraneous parentheses [-Wparentheses-equality]
if ((pdev == NULL))
~~~~~^~~~~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:539:12: note: remove extraneous
parentheses around the comparison to silence this warning
if ((pdev == NULL))
~ ^ ~
drivers/scsi/mpt3sas/mpt3sas_base.c:539:12: note: use '=' to turn this
equality comparison into an assignment
if ((pdev == NULL))
^~
=
2 warnings generated.
Remove them and while we're at it, simplify the NULL checks as '!var' is
used more than 'var == NULL'.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
All the uses have been removed, delete the macro.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Convert these uses to ioc_<level> where appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the logging level as panic calls stop the machine and should always be
emitted regardless of requested logging level.
These existing panic uses are perhaps inappropriate.
Miscellanea:
o Coalesce formats and convert MPT3SAS_FMT to "%s: " to improve clarity
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Convert the existing 2 uses to make the format and arguments matching more
obvious.
Miscellanea:
o Move the word "enabled" into the format to trivially reduce object size
o Remove unnecessary parentheses
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
These have misordered uses of __func__ and ioc->name that could mismatch
MPT3SAS_FMT and "%s: ".
Convert them to ioc_<level>.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use a more common logging style.
Done using the perl script below and some typing
$ git grep --name-only -w MPT3SAS_FMT -- "*.c" | \
xargs perl -i -e 'local $/; while (<>) { s/\bpr_(info|err|notice|warn)\s*\(\s*MPT3SAS_FMT\s*("[^"]+"(?:\s*\\?\s*"[^"]+"\s*){0,5}\s*),\s*ioc->name\s*/ioc_\1(ioc, \2/g; print;}'
Miscellanea for these conversions:
o Coalesce formats
o Realign arguments
o Remove unnecessary parentheses
o Use casts to u64 instead of unsigned long long where appropriate
o Convert broken pr_info uses to pr_cont
o Fix broken format string concatenation with line continuations and
excess whitespace
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
These macros can help identify specific logging uses and eventually perhaps
reduce object sizes.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The few callers can just use dma_set_max_seg_size ()directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
After bfcb79fca1 ("PCI/ERR: Run error recovery callbacks for all affected
devices"), AER errors are always cleared by the PCI core and drivers don't
need to do it themselves.
Remove calls to pci_cleanup_aer_uncorrect_error_status() from device
driver error recovery functions.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog, remove PCI core changes, remove unused variables]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
*) Add new PHY driver for Socionext PCIe, USB2 and USB3 PHY
*) Add new PHY driver for Rockchip HDMI PHY
*) Add new PHY driver for Cadence display port PHY
*) Add support for UFS PHY in Qualcomm's SDM845 SoC
*) Add correct PHY init sequence for BCM63138 SATA PHY
*) Add support for bringing the uart2 out through the usb dm+dp pin in
Rockchips's rk3188
*) Re-design R-Car Gen3 USB PHY w.r.t support for OTG
*) Cleanup Qualcomm's UFS PHY, QMP PHY (for PCIe and USB3) and QUSB2 PHY
*) A preparation patch to remove the node name pointer from struct device_node
*) Minor cleanups in some of the other PHY drivers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=A4II
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.20
*) Add new PHY driver for Socionext PCIe, USB2 and USB3 PHY
*) Add new PHY driver for Rockchip HDMI PHY
*) Add new PHY driver for Cadence display port PHY
*) Add support for UFS PHY in Qualcomm's SDM845 SoC
*) Add correct PHY init sequence for BCM63138 SATA PHY
*) Add support for bringing the uart2 out through the usb dm+dp pin in
Rockchips's rk3188
*) Re-design R-Car Gen3 USB PHY w.r.t support for OTG
*) Cleanup Qualcomm's UFS PHY, QMP PHY (for PCIe and USB3) and QUSB2 PHY
*) A preparation patch to remove the node name pointer from struct device_node
*) Minor cleanups in some of the other PHY drivers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (41 commits)
phy: renesas: convert to SPDX identifiers
phy: lantiq: Fix compile warning
phy: qcom-ufs: Declare 20nm qcom ufs qmp phy as Broken
scsi/ufs: qcom: Remove ufs_qcom_phy_*() calls from host
phy: qcom-ufs: Remove stale methods that handle ref clk
dt-bindings: phy-qcom-qmp: Add UFS phy compatible string for sdm845
phy: Add QMP phy based UFS phy support for sdm845
phy: General struct and field cleanup
phy: Update PHY power control sequence
phy: rockchip-usb: add usb-uart setup for rk3188
phy: phy-twl4030-usb: fix denied runtime access
phy: renesas: rcar-gen3-usb2: add is_otg_channel to use "role" sysfs
phy: renesas: rcar-gen3-usb2: add conditions for uses_otg_pins == false
phy: renesas: rcar-gen3-usb2: change a condition "dr_mode"
phy: renesas: rcar-gen3-usb2: unify OBINTEN handling
phy: renesas: rcar-gen3-usb2: Check a property to use otg pins
phy: renesas: rcar-gen3-usb2: Rename has_otg_pins to uses_otg_pins
phy: renesas: rcar-gen3-usb2: fix vbus_ctrl for role sysfs
dt-bindings: rcar-gen3-phy-usb2: add no-otg-pins property
phy: brcm-sata: Add BCM63138 (DSL) PHY init sequence
...
-----BEGIN PGP SIGNATURE-----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=dMl4
-----END PGP SIGNATURE-----
Merge tag 'v4.19-rc6' into for-4.20/block
Merge -rc6 in, for two reasons:
1) Resolve a trivial conflict in the blk-mq-tag.c documentation
2) A few important regression fixes went into upstream directly, so
they aren't in the 4.20 branch.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* tag 'v4.19-rc6': (780 commits)
Linux 4.19-rc6
MAINTAINERS: fix reference to moved drivers/{misc => auxdisplay}/panel.c
cpufreq: qcom-kryo: Fix section annotations
perf/core: Add sanity check to deal with pinned event failure
xen/blkfront: correct purging of persistent grants
Revert "xen/blkfront: When purging persistent grants, keep them in the buffer"
selftests/powerpc: Fix Makefiles for headers_install change
blk-mq: I/O and timer unplugs are inverted in blktrace
dax: Fix deadlock in dax_lock_mapping_entry()
x86/boot: Fix kexec booting failure in the SEV bit detection code
bcache: add separate workqueue for journal_write to avoid deadlock
drm/amd/display: Fix Edid emulation for linux
drm/amd/display: Fix Vega10 lightup on S3 resume
drm/amdgpu: Fix vce work queue was not cancelled when suspend
Revert "drm/panel: Add device_link from panel device to DRM device"
xen/blkfront: When purging persistent grants, keep them in the buffer
clocksource/drivers/timer-atmel-pit: Properly handle error cases
block: fix deadline elevator drain for zoned block devices
ACPI / hotplug / PCI: Don't scan for non-hotplug bridges if slot is not bridge
drm/syncobj: Don't leak fences when WAIT_FOR_SUBMIT is set
...
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When pcmcia_enable_device fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling pcmcia_enable_device
in the qlogic_stub scsi driver.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
[linux@dominikbrodowski.net: update commit message]
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Use module_pcmcia_driver for drivers whose init and exit functions
only register and unregister, respectively.
A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:
@a@
identifier f, x;
@@
-static f(...) { return pcmcia_register_driver(&x); }
@b depends on a@
identifier e, a.x;
@@
-static e(...) { pcmcia_unregister_driver(&x); }
@c depends on a && b@
identifier a.f;
declarer name module_init;
@@
-module_init(f);
@d depends on a && b && c@
identifier b.e, a.x;
declarer name module_exit;
declarer name module_pcmcia_driver;
@@
-module_exit(e);
+module_pcmcia_driver(x);
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
[linux@dominikbrodowski.net:
- updated commit message
- drop change to fdomain which got removed in the meantime]
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This patch fixes commit bcc71cc3cd ("scsi: qla2xxx: Fix for double
free of SRB structure") which placed code in wrong routines.
Also updated the use of WARN_ON() to WARN_ON_ONCE() to prevent
flooding log messages.
Fixes: bcc71cc3cd ("scsi: qla2xxx: Fix for double free of SRB structure")
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update device_add_disk() to take an 'groups' argument so that
individual drivers can register a device with additional sysfs
attributes.
This avoids race condition the driver would otherwise have if these
groups were to be created with sysfs_add_groups().
Signed-off-by: Martin Wilck <martin.wilck@suse.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The SR_RST bit isn't latched. Hence, detecting a bus reset isn't reliable.
When it is detected, the right thing to do is to drop all connected and
disconnected commands. The code for that is already present so refactor it and
call it when SR_RST is set.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The X3T9.2 specification (draft) says, under "6.1.4.2 RESELECTION time-out
procedure", that a target may assert RST or go to BUS FREE phase if the
initiator does not respond within 200 us. Something like this has been
observed with AztecMonster II target. When it happens, all we can do is wait
for the target to try again.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The X3T9.2 specification (draft) says, under "6.1.4.1 RESELECTION",
... The reselected initiator shall then assert the BSY signal
within a selection abort time of its most recent detection of being
reselected; this is required for correct operation of the time-out
procedure.
The selection abort time is only 200 us which may be insufficient time for a
printk() call. Move the diagnostics to the error paths.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When NCR5380_abort() returns FAILED, the driver forgets that the target is
still busy. Hence, further commands may be sent to the target, which may fail
during selection and produce the error message, "reselection after won
arbitration?". Prevent this by leaving the busy flag set when NCR5380_abort()
fails.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The X3T9.2 specification (draft) says, under "6.1.4.1 RESELECTION", that "the
initiator shall not respond to a RESELECTION phase if other than two SCSI ID
bits are on the DATA BUS." This issue (too many bits set) has been observed in
the wild, so add a check.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When sense data is valid, call set_driver_byte(cmd, DRIVER_SENSE). Otherwise
some callers of scsi_execute() will ignore sense data. Don't set DID_ERROR or
DID_RESET just because sense data is missing.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly needed because an AztecMonster II target has been observed
disconnecting REQUEST SENSE commands and then failing to reselect properly.
Suggested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The return value is taken to mean "retry" or "don't retry". Change it to bool
to improve readability. Fix related comments. No functional change.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace a 'goto' statement with a simple 'return' where possible. This
improves readability. No functional change.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When doing a host reset we should be clearing all outstanding commands, not
just the command triggering the reset.
[mkp: adjusted Hannes' SoB address]
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Ondrey Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The check for a non-zero drvr_wait is redundant as the same check is performed
earlier in the outer while loop, the inner check will always be true if we
reached this point inside the while loop. Remove the redundant if check.
Detected by cppcheck:
(warning) Identical inner 'if' condition is always true.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a probability that the SRB structure might have been released by the
time the debug log message dereferences it. This patch moved the log messages
before the command is issued to the firmware to prevent unknown behavior and
kernel crash
Fixes: 726b854870 ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch prevents user space mailbox request from doing chip reset if the
mailbox timed out. The chip reset is only reserved for the DPC thread to
ensure all mailbox requests are flushed properly. The DPC thread is
responsible for the flushing all MBs and chip reset.
Fixes: b2000805a9 ("scsi: qla2xxx: Flush mailbox commands on chip reset")
Cc: <stable@ger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes multiple call for qla_nvme_unregister_remote_port() as part
of qlt_schedule_session_for_deletion(), Do not call it again during
qla_nvme_delete()
Fixes: e473b30741 ("scsi: qla2xxx: Add FC-NVMe abort processing")
Cc: <stable@vger.kernel.org>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes issue where driver clears NPort ID map instead of marking
handle in use. Once driver clears NPort ID from the database, it can reuse
the same NPort ID resulting in a PLOGI failure.
[mkp: fixed Himanshu's SoB]
Fixes: a084fd68e1 ("scsi: qla2xxx: Fix re-login for Nport Handle in use")
Cc: <stable@vger.kernel.org>
Signed-of-by: Quinn Tran <quinn.tran@cavium.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Himanshu Madhani <hmadhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The response data buffer used in switch scan is reused 4 times. (For example,
for commands GPN_FT, GNN_FT for FCP and FC-NVME) Before driver reuses this
buffer, clear it to prevent duplicate entries in our database.
Fixes: a4239945b8 ("scsi: qla2xxx: Add switch command to simplify fabric discovery"
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes issue when remoteport registers itself as both FCP and
FC-NVMe with the switch, driver will pick FC-NVMe personality as default when
scanning for targets.
Driver was using comaprative operator instead of bitwise operator to check for
fc4_type for both FCP and FC-NVME.
Fixes: 2b5b96473e ("scsi: qla2xxx: Fix FC-NVMe LUN discovery")
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We shouldn't allow negative thresholds. I don't know what it would do
but it can't be good.
Fixes: 8b4673ba3a ("scsi: qla2xxx: Add support for ZIO6 interrupt threshold")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Default value of ql2xasynctmfenable for qla2xxx driver was set to 1 in
commit 043dc1d7e8 ("scsi: qla2xxx: Enable Async TMF processing") but
comment in MODULE_PARAM_DESC was not modified.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The RQF_PREEMPT flag is used for three purposes:
- In the SCSI core, for making sure that power management requests
are executed even if a device is in the "quiesced" state.
- For domain validation by SCSI drivers that use the parallel port.
- In the IDE driver, for IDE preempt requests.
Rename "preempt-only" into "pm-only" because the primary purpose of
this mode is power management. Since the power management core may
but does not have to resume a runtime suspended device before
performing system-wide suspend and since a later patch will set
"pm-only" mode as long as a block device is runtime suspended, make
it possible to set "pm-only" mode from more than one context. Since
with this change scsi_device_quiesce() is no longer idempotent, make
that function return early if it is called for a quiesced queue.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Cc: Jianchao Wang <jianchao.w.wang@oracle.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move the code for runtime power management from blk-core.c into the
new source file blk-pm.c. Move the corresponding declarations from
<linux/blkdev.h> into <linux/blk-pm.h>. For CONFIG_PM=n, leave out
the declarations of the functions that are not used in that mode.
This patch not only reduces the number of #ifdefs in the block layer
core code but also reduces the size of header file <linux/blkdev.h>
and hence should help to reduce the build time of the Linux kernel
if CONFIG_PM is not defined.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Jianchao Wang <jianchao.w.wang@oracle.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The host makes direct calls into phy using ufs_qcom_phy_*()
APIs. These APIs are only defined for 20nm qcom-ufs-qmp phy
which is not being used by any architecture as yet. Future
architectures too are not going to use 20nm ufs phy.
So remove these ufs_qcom_phy_*() calls from host to let further
change declare the 20nm phy as broken.
Also remove couple of stale enum defines for ufs phy.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When the lldd is processing the complete sas task in interrupt and set the
task stat as SAS_TASK_STATE_DONE, the smp timeout timer is able to be
triggered at the same time. And smp_task_timedout() will complete the task
wheter the SAS_TASK_STATE_DONE is set or not. Then the sas task may freed
before lldd end the interrupt process. Thus a use-after-free will happen.
Fix this by calling the complete() only when SAS_TASK_STATE_DONE is not
set. And remove the check of the return value of the del_timer(). Once the
LLDD sets DONE, it must call task->done(), which will call
smp_task_done()->complete() and the task will be completed and freed
correctly.
Reported-by: chenxiang <chenxiang66@hisilicon.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When ata device IDENTIFY failed, the ata device status is ATA_DEV_UNKNOWN. The
libata reported like:
[113518.620433] ata5.00: qc timeout (cmd 0xec)
[113518.653646] ata5.00: failed to IDENTIFY (I/O error, err_mask=0x4)
But libsas verifies the device status by ata_dev_disabled(), which skipped
ATA_DEV_UNKNOWN. This will make libsas think the ata device probing succeed
the device cannot be actually brought up. And even the new bcast of this
device will be considered as flutter and will not probe this device again.
Change ata_dev_disabled() to !ata_dev_enabled() so that libsas can deal with
this if the ata device probe failed. New bcasts can let us try to probe the
device again and bring it up if it is fine to IDENTIFY.
Tested-by: Zhou Yupeng <zhouyupeng1@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If we went into sas_rediscover_dev() the attached_sas_addr was already insured
not to be zero. So it's unnecessary to check if the attached_sas_addr is zero.
And although if the sas address is not changed, we always have to unregister
the old device when we are going to register a new one. We cannot just leave
the device there and bring up the new.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: chenxiang <chenxiang66@hisilicon.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now LLDDs have to implement lldd_port_deformed method otherwise NULL
dereference will happen. Make it optional and remove the dummy implementation
in hisi_sas.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Acked-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This code is dead and no clue implies that it will be back again.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Johannes Thumshirn <jthumshirn@suse.de>
CC: Ewan Milne <emilne@redhat.com>
CC: Christoph Hellwig <hch@lst.de>
CC: Tomas Henzl <thenzl@redhat.com>
CC: Dan Williams <dan.j.williams@intel.com>
CC: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to spelling mistake in warning message and comments
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clang warns when multiple pairs of parentheses are used for a single
conditional statement.
In file included from drivers/scsi/BusLogic.c:57:
drivers/scsi/FlashPoint.c:2947:34: warning: equality comparison with extraneous parentheses [-Wparentheses-equality]
if ((currSCCB->Sccb_scsistat == SELECT_SN_ST)) {
~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~
drivers/scsi/FlashPoint.c:2947:34: note: remove extraneous parentheses around the comparison to silence this warning
if ((currSCCB->Sccb_scsistat == SELECT_SN_ST)) {
~ ^ ~
drivers/scsi/FlashPoint.c:2947:34: note: use '=' to turn this equality comparison into an assignment
if ((currSCCB->Sccb_scsistat == SELECT_SN_ST)) {
^~
=
drivers/scsi/FlashPoint.c:2956:39: warning: equality comparison with extraneous parentheses [-Wparentheses-equality]
else if ((currSCCB->Sccb_scsistat ==
~~~~~~~~~~~~~~~~~~~~~~~~^~
drivers/scsi/FlashPoint.c:2956:39: note: remove extraneous parentheses around the comparison to silence this warning
else if ((currSCCB->Sccb_scsistat ==
~ ^
drivers/scsi/FlashPoint.c:2956:39: note: use '=' to turn this equality comparison into an assignment
else if ((currSCCB->Sccb_scsistat ==
^~
=
2 warnings generated.
Link: https://github.com/ClangBuiltLinux/linux/issues/156
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Khalid Aziz <khalid@gonehiking.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
vmemdup_user is better than duplicating its implementation, So just replace
the open code.
The issue is detected with the help of Coccinelle.
Tested-by: Don Brace <don.brace@microsemi.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Version bump conflict in batman-adv, take what's in net-next.
iavf conflict, adjustment of netdev_ops in net-next conflicting
with poll controller method removal in net.
Signed-off-by: David S. Miller <davem@davemloft.net>
When sd_init_command() get's a command with a unknown req_op() it crashes the
system via BUG().
This makes debugging the actual reason for the broken request cmd_flags pretty
hard as the system is down before it's able to write out debugging data on the
serial console or the trace buffer.
Change the BUG() to a WARN_ON() and return BLKPREP_KILL to fail gracefully and
return an I/O error to the producer of the request.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While dlpar adding primary ipr adapter back, driver goes through adapter
initialization then schedule ipr_worker_thread to start te disk scan by
dropping the host lock, calling scsi_add_device. Then get the adapter reset
request again, so driver does scsi_block_requests, this will cause the
scsi_add_device get hung until we unblock. But we can't run ipr_worker_thread
to do the unblock because its stuck in scsi_add_device.
This patch fixes the issue.
[mkp: typo and whitespace fixes]
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clang warns when multiple pairs of parentheses are used for a single
conditional statement.
drivers/scsi/advansys.c:6451:20: warning: equality comparison with
extraneous parentheses [-Wparentheses-equality]
if ((sdtr_data == 0xFF)) {
~~~~~~~~~~^~~~~~~
drivers/scsi/advansys.c:6451:20: note: remove extraneous parentheses
around the comparison to silence this warning
if ((sdtr_data == 0xFF)) {
~ ^ ~
drivers/scsi/advansys.c:6451:20: note: use '=' to turn this equality
comparison into an assignment
if ((sdtr_data == 0xFF)) {
^~
=
1 warning generated.
Link: https://github.com/ClangBuiltLinux/linux/issues/155
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver currently uses the ndlp to get the local rport which is then used
to get the nvme transport remoteport pointer. There can be cases where a stale
remoteport pointer is obtained as synchronization isn't done through the
different dereferences.
Correct by using locks to synchronize the dereferences.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
blk-mq does not support runtime pm, so disable blk-mq support for now.
Fixes: d5038a13ec ("scsi: core: switch to scsi-mq by default")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/qla2xxx/qla_iocb.c: In function 'qla24xx_els_dcmd2_iocb':
drivers/scsi/qla2xxx/qla_iocb.c:2644:13: warning:
variable 'ptr_dma' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/lpfc/lpfc_nvme.c: In function 'lpfc_new_nvme_buf':
drivers/scsi/lpfc/lpfc_nvme.c:2238:24: warning:
variable 'sgl_size' set but not used [-Wunused-but-set-variable]
int bcnt, num_posted, sgl_size;
^
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently a scsi device won't contribute to kernel randomness when it uses
blk-mq. Since we commonly use scsi on rotational device with blk-mq, it make
sense to keep contributing to kernel randomness in these cases. This is
especially important for virtual machines.
commit b5b6e8c8d3 ("scsi: virtio_scsi: fix IO hang caused by automatic irq
vector affinity") made all virtio-scsi device to use blk-mq, which does not
contribute to randomness today. So for a virtual machine only having
virtio-scsi disk (which is common), it will simple stop getting randomness
from its disks in today's implementation.
With this patch, if the above VM has rotational virtio-scsi device, then it
can still benefit from the entropy generated from the disk.
Reported-by: Xuewei Zhang <xueweiz@google.com>
Signed-off-by: Xuewei Zhang <xueweiz@google.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/bnx2fc/bnx2fc_fcoe.c: In function 'bnx2fc_rcv':
drivers/scsi/bnx2fc/bnx2fc_fcoe.c:435:17: warning:
variable 'oxid' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While reviewing another part of the code, Kees noticed that the strncpy of the
partition name might not always be NUL terminated. Switch to using strscpy
which does this safely.
Reported-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There's currently a warning about string overflow with strncat:
drivers/scsi/ibmvscsi_tgt/ibmvscsi_tgt.c: In function 'ibmvscsis_probe':
drivers/scsi/ibmvscsi_tgt/ibmvscsi_tgt.c:3479:2: error: 'strncat' specified
bound 64 equals destination size [-Werror=stringop-overflow=]
strncat(vscsi->eye, vdev->name, MAX_EYE);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Switch to a single snprintf instead of a strcpy + strcat to handle this
cleanly.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
BUG_ON() already contains an unlikely(), there is no need for another one.
Signed-off-by: Igor Stoppa <igor.stoppa@huawei.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: linux-scsi@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/aic7xxx/aic79xx_pci.c: In function 'ahd_pci_config':
drivers/scsi/aic7xxx/aic79xx_pci.c:291:19: warning:
variable 'shared_scb_data' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/pm8001/pm80xx_hwi.c: In function 'pm8001_set_phy_profile':
drivers/scsi/pm8001/pm80xx_hwi.c:4679:6: warning:
variable 'page_code' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/pm8001/pm8001_sas.c: In function 'pm8001_I_T_nexus_event_handler':
drivers/scsi/pm8001/pm8001_sas.c:1052:6: warning:
variable 'device_id' set but not used [-Wunused-but-set-variable]
drivers/scsi/pm8001/pm8001_sas.c: In function 'pm8001_abort_task':
drivers/scsi/pm8001/pm8001_sas.c:1191:6: warning:
variable 'device_id' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Error paths in ufshcd_init() ufshcd_hba_exit() killed clk_scaling workqueue
when the workqueue is actually created quite late in ufshcd_init(). So, we
end up getting NULL pointer dereference in such error paths. Fix this by
moving clk_scaling initialization and kill codes to two separate methods, and
call them at required places.
Fixes: 401f1e4490 ("scsi: ufs: don't suspend clock scaling during clock
gating")
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Subhash Jadavani <subhashj@codeaurora.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Evan Green <evgreen@chromium.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The fib6_info reference in rt6_info is rcu protected. Add a helper
to extract prefsrc from and update cxgbi_check_route6 to use it.
Fixes: 0153167aeb ("net/ipv6: Remove rt6i_prefsrc")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updated the driver version from 0.1.38 to 0.1.39.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the firmware is not responding, execution of kexec boot causes a system
hang. When firmware assertion happened, driver get notified with interrupt
vector updated in MPI configuration table. Then, the driver will read
scratchpad register and set controller_fatal_error flag to true.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For the function dma_unmap_sg(), the <nents> parameter should be number of
elements in the scatter list prior to the mapping, not after the mapping.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added proper mask for phy id in mpi_phy_stop_resp().
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to typo in debug message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We should first do the le16_to_cpu endian conversion and then apply the
FCP_CMD_LENGTH_MASK mask.
Fixes: 5f35509db1 ("qla2xxx: Terminate exchange if corrupted")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Quinn Tran <Quinn.Tran@cavium.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable num_chip_names is defined but not used, hence it is redundant and can
be removed.
Cleans up clang warning:
'num_chip_names' defined but not used [-Wunused-const-variable=]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/libfc/fc_fcp.c: In function 'fc_queuecommand':
drivers/scsi/libfc/fc_fcp.c:1875:30: warning:
variable 'rpriv' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sym_int_sir() in sym_hipd.c does not check the command pointer for NULL before
using it in debug message prints.
Suggested-by: Matthew Wilcox <matthew.wilcox@oracle.com>
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Acked-by: Matthew Wilcox <matthew.wilcox@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver version to 12.0.0.7
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds the ability to read firmware logs from the adapter. The driver
registers a buffer with the adapter that is then written to by the adapter.
The adapter posts CQEs to indicate content updates in the buffer. While the
adapter is writing to the buffer in a circular fashion, an application will
poll the driver to read the next amount of log data from the buffer.
Driver log buffer size is configurable via the ras_fwlog_buffsize sysfs
attribute. Verbosity to be used by firmware when logging to host memory is
controlled through the ras_fwlog_level attribute. The ras_fwlog_func
attribute enables or disables loggy by firmware.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, on each io completion, the stats update routine indiscriminately
holds a lock. While holding the adapter-wide lock, checks are made to check
whether status are being tracked. When disabled (the default), the locking
wasted a lot of cycles.
Check for stats enablement before taking the lock.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Message 6408 is displayed for each entry in an array, but the cpu and queue
numbers were incorrect for the entry. Message 6001 includes an extraneous
character.
Resolve both issues
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During attachment, the driver writes the EQ doorbell to disable potential
interrupts from an EQ. The current EQ doorbell format used for clearing the
interrupt is incorrect and uses an if_type=2 format, making the operation act
on the wrong EQ.
Correct the code to use the proper if_type=6 EQ doorbell format.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When taking the board offline while performing i/o, unsafe locking errors
occurred and irq level isn't properly managed.
In lpfc_sli_hba_down, spin_lock_irqsave(&phba->hbalock, flags) does not
disable softirqs raised from timer expiry. It is possible that a softirq is
raised from the lpfc_els_retry_delay routine and recursively requests the same
phba->hbalock spinlock causing deadlock.
Address the deadlocks by creating a new port_list lock. The softirq behavior
can then be managed a level deeper into the calling sequences.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When running an mds diagnostic that passes frames with the switch, soft
lockups are detected. The driver is in a CQE processing loop and has
sufficient amount of traffic that it never exits the ring processing routine,
thus the "lockup".
Cap the number of elements in the work processing routine to 64 elements. This
ensures that the cpu will be given up and the handler reschedule to process
additional items.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On io completion, the driver is taking an adapter wide lock and nulling the
scsi command back pointer. The nulling of the back pointer is to signify the
io was completed and the scsi_done() routine was called. However, the routine
makes no check to see if the abort routine had done the same thing and
possibly nulled the pointer. Thus it may doubly-complete the io.
Make the following mods:
- Check to make sure forward progress (call scsi_done()) only happens if the
command pointer was non-null.
- As the taking of the lock, which is adapter wide, is very costly on a system
under load, null the pointer using an xchg operation rather than under lock.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When nvme is enabled, change the default for two parameters:
sg_seg_cnt - raise the per-io sg list size so that 1MB ios are
supported (based on a 4k buffer per element).
iocb_cnt - raise the number of buffers used for things like
NVME LS request/responses to allow more concurrent requests
to for larger nvme configs.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver allocates a sg list per io struture based on a fixed maximum
size. When it registers with the protocol transports and indicates the max sg
list size it supports, the driver manipulates the fixed value to report a
lesser amount so that it has reserved space for sg elements that are used for
DIF.
The driver initialization path sets the cfg_sg_seg_cnt field to the
manipulated value for scsi. NVME initialization ran afterward and capped it's
maximum by the manipulated value for SCSI. This erroneously made NVME report
the SCSI-reduce-for-DIF value that reduced the max io size for nvme and wasted
sg elements.
Rework the driver so that cfg_sg_seg_cnt becomes the overall maximum size and
allow the max size to be tunable. A separate (new) scsi sg count is then
setup with the scsi-modified reduced value. NVME then initializes based off
the overall maximum.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver only sends NVME PRLI to a device that also supports FCP. This resuls
in remote ports that don't have fc_remote_ports created for them. The driver
is clearing the nlp_fc4_type for a ndlp at the wrong time.
Fix by moving the nlp_fc4_type clearing to the discovery engine in the
DEVICE_RECOVERY state. Also ensure that rport registration is done for all
nlp_fc4_types.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes issue when switch command fails, current code increments
retry count twice. This results in a smaller number of retries.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code relies on switch to provide a unique combination of WWPN +
NPORTID to tract an FC port. This patch tries to detect a case where switch
data base can get corrupted where multiple WWPNs can have the same Nport ID.
The 1st Nport ID on the list will be kept while the duplicate Nport ID will be
discarded.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When qla2xxx and Target Core gets out of sync during command cleanup, qla2xxx
will not free command until it is out of firmware's hand and Target Core has
called the release on the command.
This patch adds synchronization using cmd_lock and release flag. If the
release flag is set, then qla2xxx will free up the command using
qlt_free_cmd() otherwise transport_generic_free_cmd() will be responsible for
relase of the command.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If chip unable to fully initialize, use full shutdown sequence to clear out
any stale FW state.
Fixes: e315cd28b9 ("[SCSI] qla2xxx: Code changes for qla data structure refactoring")
Cc: stable@vger.kernel.org #4.10
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On PLOGI complete + RSCN received, driver tries to handle RSCN but failed to
reset the session back to the beginning to restart the login process. Instead
the session was left in the Plogi complete without moving forward. This patch
will push the session state back to the delete state and restart the
connection.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Task abort can take 2 paths: 1) serial/synchronous abort where the calling
thread will put to sleep, wait for completion and free cmd resource. 2) async
abort where the cmd free will be free by the completion thread. For path 2,
driver is freeing the SRB too early.
Fixes: f6145e86d2 ("scsi: qla2xxx: Fix race between switch cmd completion and timeout")
Cc: stable@vger.kernel.org # 4.19
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add ability to allow each physical port to control operating mode. Current
code forces all ports to behave in one mode (i.e. initiator, target or
dual). This patch allows user to select the operating mode for each port.
- Driver must be loaded in dual mode to allow resource allocation
modprobe qla2xxx qlini_mode=dual
- In addition user can make adjustment to exchange resources using following
command
echo 1024 > /sys/class/scsi_host/host<x>/ql2xiniexchg
echo 1024 > /sys/class/scsi_host/host<x>/ql2xexchoffld
- trigger mode change and new setting of ql2xexchoffld|ql2xiniexchg
echo [<value>] > /sys/class/scsi_host/host<x>/qlini_mode
where, value can be one of following
- enabled
- disabled
- dual
- exclusive
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For Loop topology + Initiator, FW is in control of PLOGI/PRLI. When link is
reset, driver will try to cleanup the session by doing an Implicit Logout.
Instead, the code is doing an Explicit Logout. The explicit logout interferes
with FW state machine in trying to reconnect. The implicit logout was meant
for FW to flush commands. In loop, it is not needed because FW will auto
flush.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When FW rejects a command due to "entry_status" error (malform IOCB), the srb
resource needs to be returned back for cleanup. The filter to catch this is
in the wrong location.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clear port speed value on chip reset.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During adapter shutdown process check for register disconnect before
proceeding to call PCI functions.
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Abort IOCB request can take up to 40s or 2 ABTS timeout. We will wait for
ABTS response for 20s. On a timeout, second ABTS can go out with another 20s
timeout. On 2nd ABTS timeout FW will automatically do Logout.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch allows FC-NVMe under-run to be handled by transport
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current abort code defaults to legacy single queue where hardware_lock is used
to protect command search. This patch moves this code behind the QPair where
the qp_lock_ptr will reference the appropriate lock for either legacy/single
queue or MQ.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Using GPNFT/GNNFT command will be able to cover switch database with less
number of scans. This patch removes Get NportID with provided WWPN/GIDPN
switch command. By making this change, in large fabric with lots of remote
port or NPIV ports with noisy SAN, the number of GIDPN commands issued by a
port when it detects large number of remote ports going away or coming back,
can overwhelmn the switch and it can becomde unresponsive. In a case where the
fabric has not change, GIDPN is not required.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Reduce sess_lock holding to prevent CPU Lock up. sess_lock was held across
fc_port registration and deletion. These calls can be blocked by upper
layer. Sess_lock is also being accessed by interrupt thread.
- Reduce number of loops in processing work_list to prevent kernel complaint
of CPU lockup or holding sess_lock.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, qla2x00_[get_sp|rel_sp] routines does {get|release} of srb
resource/srb_mempool directly from qla_hw_data. qla2x00_start_sp() is used to
issue management commands through the default Request Q 0 & Response Q 0 or
base_qpair. This patch moves access of these resources through
base_qpair. Instead of having knowledge of specific Q number and lock to
rsp/req queue, this change will key off the qpair that is assigned to the srb
resource. This lays the ground work for other routines to see this resource
through the qpair.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add sysfs support to control zio6 interrupt threshold. Using this sysfs hook
user can set when to generate interrupts. This value will be used to tell
firmware to generate interrupt at a certain interval. If the number of
exchanges/commands fall below defined setting, then the interrupt will be
generated immediately by the firmware.
By default ZIO6 will coalesce interrupts to a specified interval
regardless of low traffic or high traffic.
[mkp: fixed several typos]
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Following changes are added by this patch
- Prevent ABTS Response from getting in front of Termination of exchange.
Firmware requires driver to cleanup exchanges before ABTS response can be
sent. This reduces ABTS response error which triggers extra command
re-termination and re-sending of ABTS response.
- Add bits in driver and tracks CTIO/ATIO attribute bits for proper command
Termination. A copy of the ATTR bits will be kept in the ABTS task
management command as a back up copy, if an ABTS response encounters an
error.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ABTS error completion can trigger an exchange cleanup from the driver and
another ABTS response will be generated. This retry of ABTS response can
cause loop between driver trying to send ABTS and firmware returning error.
This patch fixes this issue by adding logic to check for unresolved exchanges
and clean up before ABTS is retried. This patch also addes the fix to use the
same qpair as the ABTS completion for the terminatation of exchange as well as
retry of ABTS response.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When driver detect CTIO_INVALID_RX_ID status for CTIO, print message with
correct information to help with debugging.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move ATIO queue processing out of hardware_lock to prevent deadlock.
Fixes: 3bb67df5b5 ("qla2xxx: Check for online flag instead of active reset when transmitting responses")
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For driver MBX submission, use mbox_busy to serialize request. For Userspace
MBX submission, use optrom mutex to serialize request.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When driver receive PLOGI/PRLI from FW, the WWPN value will be provided. If
it is not, then driver will terminate it. The WWPN allows driver to locate
the session or create a new session.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For target mode, any chip reset triggered before target mode is enabled will
be held off until user is ready to enable. This prevents the chip from
starting or running before it is intended.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When switch responds with error for Get Port Speed Command (GPSC), driver
should not proceed with telling FW about the speed of the remote port.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When all fabric scan retries fail, remove all RPorts, DMA resources for the
command. Otherwise we have stale Rports.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Turn ON logout_on_delete flag to make sure firmware resource for fcport is
cleaned up on ADISC error.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Turn off IOCB timeout timer on IOCB completion instead of turning it off in a
deferred task. This prevent false alarm if the deferred task is stalled out.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Decrement login retry count only for plogi instead of number of attempts made
for login.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, the rport registration is being called from a single work element
that is used to process QLA internal "work_list". This work_list is meant for
quick and simple task (ie no sleep). The Rport registration process sometime
can be delayed by upper layer. This causes back pressure with the internal
queue where other jobs are unable to move forward.
This patch will schedule the registration process with a new work element
(fc_port.reg_work). While the RPort is being registered, the current state of
the fcport will not move forward until the registration is done. If the state
of the fabric has changed, a new field/next_disc_state will record the next
action on whether to 'DELETE' or 'Reverify the session/ADISC'.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove redundant check for fcport is deleted or being delete. The same check
is already in the deletion routine.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename rscn_rcvd field to scan_needed to be more meaningful.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On Abort of initiator scsi command, the abort needs to follow the same qpair
as the the scsi command to prevent out of order processing.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch improves performance for 16G and above adapter by removing
additional call to process_response_queue().
[mkp: typo]
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After the conversion to fib6_info, rt6i_prefsrc has a single user that
reads the value and otherwise it is only set. The one reader can be
converted to use rt->from so rt6i_prefsrc can be removed, reducing
rt6_info by another 20 bytes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bare-metal toolchains don't define __linux__, so aic7xxx build with
bare-metal toolchain is broken. This driver codebase used to be partially
shared with FreeBSD, but these days there is no point in keeping the
compatibility around. So let's just drop FreeBSD related code and get rid
of __linux__ checking in order to fix the build using bare-metal
toolchains.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
kmem_cache_destroy() can handle NULL pointer correctly, so there is no
need to check NULL pointer before calling kmem_cache_destroy()
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Smatch complains about this code:
drivers/scsi/lpfc/lpfc_scsi.c:1053 lpfc_get_scsi_buf_s4()
warn: variable dereferenced before check 'lpfc_cmd' (see line 1039)
Fortunately the NULL check isn't required so I have removed it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
'NEGOTIATION' was misspelled as 'NEGOTATION'. Fixed it. It is a coding
style change which should have no impact on runtime execution of code.
Signed-off-by: Faisal Mehmood <f.m3hm00d@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable dmsg is not being used and is redundant and hence can be
removed.
Cleans up clang warning:
warning: variable 'dmsg' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variables dev and cpu are not being used and are redundant and hence can
be removed.
Cleans up clang warnings:
warning: variable 'dev' set but not used [-Wunused-but-set-variable]
warning: variable 'cpu' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I ran into a new warning on randconfig kernels:
drivers/scsi/raid_class.c: In function 'raid_match':
drivers/scsi/raid_class.c:64:24: error: unused variable 'i' [-Werror=unused-variable]
This looks like a very old problem that for some reason was very hard to
run into, but it is very easy to fix, by replacing the incorrect #ifdef
with a simpler IS_ENABLED() check.
Fixes: fac829fdca ("[SCSI] raid_attrs: fix dependency problems")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The QED driver commit, 1ac4329a1c ("qed: Add configuration information
to register dump and debug data"), removes the CRC length validation
causing nvm_get_image failure while loading qedi driver:
[qed_mcp_get_nvm_image:2700(host_10-0)]Image [0] is too big - 00006008 bytes
where only 00006004 are available
[qedi_get_boot_info:2253]:10: Could not get NVM image. ret = -12
Hence add and adjust the CRC size to iSCSI NVM image to read boot info at
qedi load time.
Signed-off-by: Nilesh Javali <nilesh.javali@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The problem is that ->reset_state is a u8 but it can be set to -1 or -2 in
aac_tmf_callback() and the error handling in aac_eh_target_reset() relies
on it to be signed.
[mkp: fixed typo]
Fixes: 0d643ff3c3 ("scsi: aacraid: use aac_tmf_callback for reset fib")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit 328728630d.
There is fundamental issue in commit 328728630d (scsi: core: avoid
host-wide host_busy counter for scsi_mq) because SCSI's host busy counter
may not be same with counter of blk-mq's inflight tags, especially in case
of none io scheduler.
We may switch to other approach for addressing this scsi_mq's performance
issue, such as percpu counter or kind of ways, so revert this commit first
for fixing this kind of issue in EH path, as reported by Jens.
Cc: Omar Sandoval <osandov@fb.com>,
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>,
Cc: James Bottomley <james.bottomley@hansenpartnership.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: Don Brace <don.brace@microsemi.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Reported-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit 265d59aacb.
There is fundamental issue in commit 328728630d (scsi: core: avoid
host-wide host_busy counter for scsi_mq) because SCSI's host busy counter
may not be same with counter of blk-mq's inflight tags, especially in case
of none io scheduler.
So revert this commit first.
Cc: Omar Sandoval <osandov@fb.com>,
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>,
Cc: James Bottomley <james.bottomley@hansenpartnership.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: Don Brace <don.brace@microsemi.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jens Axboe <axboe@kernel.dk>
Reported-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
e2c7b43 was supposed to limit transfer length to 1MB, but got the unit of
max_sectors wrong.
Fixes: e2c7b433f7 ("scsi: hpsa: limit transfer length to 1MB")
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A recent change added some MDS processing in the lpfc_drain_txq routine
that relies on the fcp_wq being allocated. For nvmet operation the fcp_wq
is not allocated because it can only be an nvme-target. When the original
MDS support was added LS_MDS_LOOPBACK was defined wrong, (0x16) it should
have been 0x10 (decimal value used for hex setting). This incorrect value
allowed MDS_LOOPBACK to be set simultaneously with LS_NPIV_FAB_SUPPORTED,
causing the driver to crash when it accesses the non-existent fcp_wq.
Correct the bad value setting for LS_MDS_LOOPBACK.
Fixes: ae9e28f36a ("lpfc: Add MDS Diagnostic support.")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Tested-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change default behavior for fdmi registration to on.
[mkp: patch was mangled]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- use be32_to_cpu() instead of ntohs() for 32 bit port capabilities.
- add a new function fwcaps32_to_caps16() to convert 32 bit port
capabilities to 16 bit port capabilities.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The default was changed, but the help text was not updated.
Fix grammar (s/the option/this option/) while at it.
[mkp: drop "new" as suggested by John Garry]
Fixes: d5038a13ec ("scsi: core: switch to scsi-mq by default")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull IDA updates from Matthew Wilcox:
"A better IDA API:
id = ida_alloc(ida, GFP_xxx);
ida_free(ida, id);
rather than the cumbersome ida_simple_get(), ida_simple_remove().
The new IDA API is similar to ida_simple_get() but better named. The
internal restructuring of the IDA code removes the bitmap
preallocation nonsense.
I hope the net -200 lines of code is convincing"
* 'ida-4.19' of git://git.infradead.org/users/willy/linux-dax: (29 commits)
ida: Change ida_get_new_above to return the id
ida: Remove old API
test_ida: check_ida_destroy and check_ida_alloc
test_ida: Convert check_ida_conv to new API
test_ida: Move ida_check_max
test_ida: Move ida_check_leaf
idr-test: Convert ida_check_nomem to new API
ida: Start new test_ida module
target/iscsi: Allocate session IDs from an IDA
iscsi target: fix session creation failure handling
drm/vmwgfx: Convert to new IDA API
dmaengine: Convert to new IDA API
ppc: Convert vas ID allocation to new IDA API
media: Convert entity ID allocation to new IDA API
ppc: Convert mmu context allocation to new IDA API
Convert net_namespace to new IDA API
cb710: Convert to new IDA API
rsxx: Convert to new IDA API
osd: Convert to new IDA API
sd: Convert to new IDA API
...
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
This is mostly updates to the usual drivers: mpt3sas, lpfc, qla2xxx,
hisi_sas, smartpqi, megaraid_sas, arcmsr. In addition, with the
continuing absence of Nic we have target updates for tcmu and target
core (all with reviews and acks). The biggest observable change is
going to be that we're (again) trying to switch to mulitqueue as the
default (a user can still override the setting on the kernel command
line). Other major core stuff is the removal of the remaining
Microchannel drivers, an update of the internal timers and some
reworks of completion and result handling.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCW3R3niYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishauRAP4yfBKK
dbxF81c/Bxi/Stk16FWkOOrjs4CizwmnMcpM5wD/UmM9o6ebDzaYpZgA8wIl7X/N
o/JckEZZpIp+5NySZNc=
=ggLB
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates to the usual drivers: mpt3sas, lpfc, qla2xxx,
hisi_sas, smartpqi, megaraid_sas, arcmsr.
In addition, with the continuing absence of Nic we have target updates
for tcmu and target core (all with reviews and acks).
The biggest observable change is going to be that we're (again) trying
to switch to mulitqueue as the default (a user can still override the
setting on the kernel command line).
Other major core stuff is the removal of the remaining Microchannel
drivers, an update of the internal timers and some reworks of
completion and result handling"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: core: use blk_mq_run_hw_queues in scsi_kick_queue
scsi: ufs: remove unnecessary query(DM) UPIU trace
scsi: qla2xxx: Fix issue reported by static checker for qla2x00_els_dcmd2_sp_done()
scsi: aacraid: Spelling fix in comment
scsi: mpt3sas: Fix calltrace observed while running IO & reset
scsi: aic94xx: fix an error code in aic94xx_init()
scsi: st: remove redundant pointer STbuffer
scsi: qla2xxx: Update driver version to 10.00.00.08-k
scsi: qla2xxx: Migrate NVME N2N handling into state machine
scsi: qla2xxx: Save frame payload size from ICB
scsi: qla2xxx: Fix stalled relogin
scsi: qla2xxx: Fix race between switch cmd completion and timeout
scsi: qla2xxx: Fix Management Server NPort handle reservation logic
scsi: qla2xxx: Flush mailbox commands on chip reset
scsi: qla2xxx: Fix unintended Logout
scsi: qla2xxx: Fix session state stuck in Get Port DB
scsi: qla2xxx: Fix redundant fc_rport registration
scsi: qla2xxx: Silent erroneous message
scsi: qla2xxx: Prevent sysfs access when chip is down
scsi: qla2xxx: Add longer window for chip reset
...
Nobody commented on this patch back in July. So now it gets merged.
* SCSI_IOCTL_SEND_COMMAND cleanup:
scsi sg: remove incorrect scsi command checking logic
-----BEGIN PGP SIGNATURE-----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=b9ib
-----END PGP SIGNATURE-----
Merge tag 'for-4.19/block-20180812' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"First pull request for this merge window, there will also be a
followup request with some stragglers.
This pull request contains:
- Fix for a thundering heard issue in the wbt block code (Anchal
Agarwal)
- A few NVMe pull requests:
* Improved tracepoints (Keith)
* Larger inline data support for RDMA (Steve Wise)
* RDMA setup/teardown fixes (Sagi)
* Effects log suppor for NVMe target (Chaitanya Kulkarni)
* Buffered IO suppor for NVMe target (Chaitanya Kulkarni)
* TP4004 (ANA) support (Christoph)
* Various NVMe fixes
- Block io-latency controller support. Much needed support for
properly containing block devices. (Josef)
- Series improving how we handle sense information on the stack
(Kees)
- Lightnvm fixes and updates/improvements (Mathias/Javier et al)
- Zoned device support for null_blk (Matias)
- AIX partition fixes (Mauricio Faria de Oliveira)
- DIF checksum code made generic (Max Gurtovoy)
- Add support for discard in iostats (Michael Callahan / Tejun)
- Set of updates for BFQ (Paolo)
- Removal of async write support for bsg (Christoph)
- Bio page dirtying and clone fixups (Christoph)
- Set of bcache fix/changes (via Coly)
- Series improving blk-mq queue setup/teardown speed (Ming)
- Series improving merging performance on blk-mq (Ming)
- Lots of other fixes and cleanups from a slew of folks"
* tag 'for-4.19/block-20180812' of git://git.kernel.dk/linux-block: (190 commits)
blkcg: Make blkg_root_lookup() work for queues in bypass mode
bcache: fix error setting writeback_rate through sysfs interface
null_blk: add lock drop/acquire annotation
Blk-throttle: reduce tail io latency when iops limit is enforced
block: paride: pd: mark expected switch fall-throughs
block: Ensure that a request queue is dissociated from the cgroup controller
block: Introduce blk_exit_queue()
blkcg: Introduce blkg_root_lookup()
block: Remove two superfluous #include directives
blk-mq: count the hctx as active before allocating tag
block: bvec_nr_vecs() returns value for wrong slab
bcache: trivial - remove tailing backslash in macro BTREE_FLAG
bcache: make the pr_err statement used for ENOENT only in sysfs_attatch section
bcache: set max writeback rate when I/O request is idle
bcache: add code comments for bset.c
bcache: fix mistaken comments in request.c
bcache: fix mistaken code comments in bcache.h
bcache: add a comment in super.c
bcache: avoid unncessary cache prefetch bch_btree_node_get()
bcache: display rate debug parameters to 0 when writeback is not running
...
Pull vfs open-related updates from Al Viro:
- "do we need fput() or put_filp()" rules are gone - it's always fput()
now. We keep track of that state where it belongs - in ->f_mode.
- int *opened mess killed - in finish_open(), in ->atomic_open()
instances and in fs/namei.c code around do_last()/lookup_open()/atomic_open().
- alloc_file() wrappers with saner calling conventions are introduced
(alloc_file_clone() and alloc_file_pseudo()); callers converted, with
much simplification.
- while we are at it, saner calling conventions for path_init() and
link_path_walk(), simplifying things inside fs/namei.c (both on
open-related paths and elsewhere).
* 'work.open3' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (40 commits)
few more cleanups of link_path_walk() callers
allow link_path_walk() to take ERR_PTR()
make path_init() unconditionally paired with terminate_walk()
document alloc_file() changes
make alloc_file() static
do_shmat(): grab shp->shm_file earlier, switch to alloc_file_clone()
new helper: alloc_file_clone()
create_pipe_files(): switch the first allocation to alloc_file_pseudo()
anon_inode_getfile(): switch to alloc_file_pseudo()
hugetlb_file_setup(): switch to alloc_file_pseudo()
ocxlflash_getfile(): switch to alloc_file_pseudo()
cxl_getfile(): switch to alloc_file_pseudo()
... and switch shmem_file_setup() to alloc_file_pseudo()
__shmem_file_setup(): reorder allocations
new wrapper: alloc_file_pseudo()
kill FILE_{CREATED,OPENED}
switch atomic_open() and lookup_open() to returning 0 in all success cases
document ->atomic_open() changes
->atomic_open(): return 0 in all success cases
get rid of 'opened' in path_openat() and the helpers downstream
...
Eight fixes. The most important one is the mpt3sas fix which makes
the driver work again on big endian systems. The rest are mostly
minor error path or checker issues and the vmw_scsi one fixes a
performance problem.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCW28FqCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishRC9AP9sRmgl
MunaMCjubXaN2jkmyoga43ZckSVXz0wQUALI9gD+PE0At8vCbWx0tFTQLN5/QEtC
HsVMiAdHSZ87wF7ZQtw=
=ehub
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Eight fixes.
The most important one is the mpt3sas fix which makes the driver work
again on big endian systems. The rest are mostly minor error path or
checker issues and the vmw_scsi one fixes a performance problem"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: vmw_pvscsi: Return DID_RESET for status SAM_STAT_COMMAND_TERMINATED
scsi: sr: Avoid that opening a CD-ROM hangs with runtime power management enabled
scsi: mpt3sas: Swap I/O memory read value back to cpu endianness
scsi: fcoe: clear FC_RP_STARTED flags when receiving a LOGO
scsi: fcoe: drop frames in ELS LOGO error path
scsi: fcoe: fix use-after-free in fcoe_ctlr_els_send
scsi: qedi: Fix a potential buffer overflow
scsi: qla2xxx: Fix memory leak for allocating abort IOCB
We don't use blk-mq start/stop hw queue any more, so no reason to use
blk_mq_start_hw_queues which does clear_bit, replace it with
blk_mq_run_hw_queues.
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch removes redundant trace that occurs when sending Device
Management(DM) request (fix behavior in commit 6667e6d91c ("scsi:
ufs: add trace event for ufs upiu").
Since the function send_command is called also for DM request, UPIU
trace for DM request is called twice- one identified as query_* the
other as send/complete.
Signed-off-by: Ohad Sharabi <ohad.sharabi@wdc.com>
Fixes: 6667e6d91c ("scsi: ufs: add trace event for ufs upiu")
Reviewed-by: Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes following Smatch complaint:
drivers/scsi/qla2xxx/qla_iocb.c:2647 qla2x00_els_dcmd2_sp_done()
error: we previously assumed 'e' could be null (see line 2631)
Fixes: 8777e4314d ("scsi: qla2xxx: Migrate NVME N2N handling into state machine")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We accidentally return success instead of -ENOMEM on this error path.
Fixes: 2908d778ab ("[SCSI] aic94xx: new driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pointer STbuffer is being assigned but is never used hence it is redundant
and can be removed.
Cleans up clang warning:
warning: variable 'STbuffer' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAltU8z0eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG5X8H/2fJr7m3k242+t76
sitwvx1eoPqTgryW59dRKm9IuXAGA+AjauvHzaz1QxomeQa50JghGWefD0eiJfkA
1AphQ/24EOiAbbVk084dAI/C2p122dE4D5Fy7CrfLnuouyrbFaZI5STbnrRct7sR
9deeYW0GDHO1Uenp4WDCj0baaqJqaevZ+7GG09DnWpya2nQtSkGBjqn6GpYmrfOU
mqFuxAX8mEOW6cwK16y/vYtnVjuuMAiZ63/OJ8AQ6d6ArGLwAsdn7f8Fn4I4tEr2
L0d3CRLUyegms4++Dmlu05k64buQu46WlPhjCZc5/Ts4kjrNxBuHejj2/jeSnUSt
vJJlibI=
=42a5
-----END PGP SIGNATURE-----
Merge tag 'v4.18-rc6' into for-4.19/block2
Pull in 4.18-rc6 to get the NVMe core AEN change to avoid a
merge conflict down the line.
Signed-of-by: Jens Axboe <axboe@kernel.dk>
Commands that are reset are returned with status
SAM_STAT_COMMAND_TERMINATED. PVSCSI currently returns DID_OK |
SAM_STAT_COMMAND_TERMINATED which fails the command. Instead, set hostbyte
to DID_RESET to allow upper layers to retry.
Tested by copying a large file between two pvscsi disks on same adapter
while performing a bus reset at 1-second intervals. Before fix, commands
sometimes fail with DID_OK. After fix, commands observed to fail with
DID_RESET.
Signed-off-by: Jim Gill <jgill@vmware.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Surround scsi_execute() calls with scsi_autopm_get_device() and
scsi_autopm_put_device(). Note: removing sr_mutex protection from the
scsi_cd_get() and scsi_cd_put() calls is safe because the purpose of
sr_mutex is to serialize cdrom_*() calls.
This patch avoids that complaints similar to the following appear in the
kernel log if runtime power management is enabled:
INFO: task systemd-udevd:650 blocked for more than 120 seconds.
Not tainted 4.18.0-rc7-dbg+ #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
systemd-udevd D28176 650 513 0x00000104
Call Trace:
__schedule+0x444/0xfe0
schedule+0x4e/0xe0
schedule_preempt_disabled+0x18/0x30
__mutex_lock+0x41c/0xc70
mutex_lock_nested+0x1b/0x20
__blkdev_get+0x106/0x970
blkdev_get+0x22c/0x5a0
blkdev_open+0xe9/0x100
do_dentry_open.isra.19+0x33e/0x570
vfs_open+0x7c/0xd0
path_openat+0x6e3/0x1120
do_filp_open+0x11c/0x1c0
do_sys_open+0x208/0x2d0
__x64_sys_openat+0x59/0x70
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Maurizio Lombardi <mlombard@redhat.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <stable@vger.kernel.org>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Swap the I/O memory read value back to cpu endianness before storing it in
a data structures which are defined in the MPI headers where u8 components
are not defined in the endianness order.
In this area from day one mpt3sas driver is using le32_to_cpu() &
cpu_to_le32() APIs. But in commit cf6bf9710c
(mpt3sas: Bug fix for big endian systems) we have removed these APIs
before reading I/O memory which we should haven't done it. So
in this patch I am correcting it by adding these APIs back
before accessing I/O memory.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To avoid introducing problems like those fixed in commit f7068114d4
("sr: pass down correctly sized SCSI sense buffer"), this creates a macro
wrapper for scsi_execute() that verifies the size of the sense buffer
similar to what was done for command string sizes in commit 3756f6401c
("exec: avoid gcc-8 warning for get_task_comm").
Another solution could be to add a length argument to scsi_execute(),
but this function already takes a lot of arguments and Jens was not fond
of that approach.
Additionally, this moves the SCSI_SENSE_BUFFERSIZE definition into
scsi_device.h, and removes a redundant include for scsi_device.h from
scsi_cmnd.h.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There is a lot of needless struct request_sense usage in the CDROM
code. These can all be struct scsi_sense_hdr instead, to avoid any
confusion over their respective structure sizes. This patch is a lot
of noise changing "sense" to "sshdr", but the final code is more
readable to distinguish between "sense" meaning "struct request_sense"
and "sshdr" meaning "struct scsi_sense_hdr".
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Split scsi_common.o out of SCSI so that non-SCSI users can pull it in
easily for future sense buffer helper usage.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This removes the unused sense buffer in read_cap16() and write_same16().
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch fixes regression introduced for the N2N support for FC-NVMe. For
FC-NVMe with N2N connection, instead of FW initiating the Login, Driver
starts Login process. This patch migrates that new process from a
standalone path into existing session management state machine. With this
state change now driver will not wait for pull NPort ID from FW.
Fixes: edd05de197 ("scsi: qla2xxx: Changes to support N2N logins")
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Save frame payload size from init control block. This field/data is used
to register with switch database. This allows the init control block temp
buf to be reused.
[mkp: remove unused variable]
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch sets and clears FCF_ASYNC_{SENT|ACTIVE} flags to prevent
stalling of relogin attempt. Once flag are correctly set/cleared, relogin
timer can retry relogin attempt for driver to continue login.
Fixes: fa83e65885 ("scsi: qla2xxx: ensure async flags are reset correctly")
Cc: stable@vger.kernel.org #4.17
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix race condition between switch cmd completion and timeout timer. Timer
has popped triggers command free. On IOCB completion, stale sp point was
reused. Instead, an abort will be sent to FW to nudge the command out of FW
where the normal completion will take place.
RIP: 0010:qla2x00_chk_ms_status+0xf3/0x1b0 [qla2xxx]
Call Trace:
<IRQ>
qla24xx_els_ct_entry.isra.15+0x1d4/0x2b0 [qla2xxx]
qla24xx_msix_rsp_q+0x39/0xf0 [qla2xxx]
qla24xx_process_response_queue+0xbc/0x2b0 [qla2xxx]
qla24xx_msix_rsp_q+0x8a/0xf0 [qla2xxx]
__handle_irq_event_percpu+0xa0/0x1f0
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After selecting the NPort handle/loop_id, set a bit in the loop_id_map to
prevent others from selecting the same NPort handle.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Flush pending mailbox commands on chip reset. Wake up command that's
waiting for an interrupt and wait for mailbox counters to go to zero.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During normal IO, FW can return IO with 'port unavailble' status. Driver
would send a LOGO to remote port for session resync. On an off chance, a
PLOGI could arrive before sending the LOGO. This patch will skip sendiing
LOGO if a PLOGI just came in.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch sets discovery state back to GNL (Get Name List) when session is
stuck at GPDB (Get Port DataBase). This will allow state machine to retry
login and move session state ahead in discovery.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prevent multiple registrations with transport layer for the same remote
port.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver uses shadow pointer instead of Mirror pointer for firmware dump
collection. Skip those entries for Mirror pointers for Request/Response
queue from firmware dump template reading.
Following messages are printed in log messages:
qla27xx_fwdt_entry_t268: unknown buffer 4
qla27xx_fwdt_entry_t268: unknown buffer 5
This patch fixes these error messages by adding skip_entry() to not read
them from template.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prevent user from sending commands through sysfs while firmware is not
running or reset is in progress.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
qla2x00_reset_active only covers the window of turning the chip off. Add
check to cover turning chip on.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Login retry count was not properly decrementing which lead to endless
retry.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In case of N2N connect, sg_reset for bus/device/host was causing driver and
firmware state to go out of sync. This patch fixes this link instablity
when reconnect is attempted after link flap.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variables scriptb0 and dp_sgmin are being assigned but are never used
hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'scriptb0' set but not used [-Wunused-but-set-variable]
warning: variable 'dp_sgmin' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
- Updates csio_get_flash_params() to take care of ISSI, Macronix and
Winbond FLASH parts.
- Assume flash part size to be 4MB if it cannot be identified
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A long time ago the unfortunate decision was taken to add a self-deletion
attribute to the sysfs SCSI device directory. That decision was unfortunate
because self-deletion is really tricky. We can't drop that attribute
because widely used user space software depends on it, namely the
rescan-scsi-bus.sh script. Hence this patch that avoids that writing into
that attribute triggers a deadlock. See also commit 7973cbd9fbd9 ("[PATCH]
add sysfs attributes to scan and delete scsi_devices").
This patch avoids that self-removal triggers the following deadlock:
======================================================
WARNING: possible circular locking dependency detected
4.18.0-rc2-dbg+ #5 Not tainted
------------------------------------------------------
modprobe/6539 is trying to acquire lock:
000000008323c4cd (kn->count#202){++++}, at: kernfs_remove_by_name_ns+0x45/0x90
but task is already holding lock:
00000000a6ec2c69 (&shost->scan_mutex){+.+.}, at: scsi_remove_host+0x21/0x150 [scsi_mod]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&shost->scan_mutex){+.+.}:
__mutex_lock+0xfe/0xc70
mutex_lock_nested+0x1b/0x20
scsi_remove_device+0x26/0x40 [scsi_mod]
sdev_store_delete+0x27/0x30 [scsi_mod]
dev_attr_store+0x3e/0x50
sysfs_kf_write+0x87/0xa0
kernfs_fop_write+0x190/0x230
__vfs_write+0xd2/0x3b0
vfs_write+0x101/0x270
ksys_write+0xab/0x120
__x64_sys_write+0x43/0x50
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe
-> #0 (kn->count#202){++++}:
lock_acquire+0xd2/0x260
__kernfs_remove+0x424/0x4a0
kernfs_remove_by_name_ns+0x45/0x90
remove_files.isra.1+0x3a/0x90
sysfs_remove_group+0x5c/0xc0
sysfs_remove_groups+0x39/0x60
device_remove_attrs+0x82/0xb0
device_del+0x251/0x580
__scsi_remove_device+0x19f/0x1d0 [scsi_mod]
scsi_forget_host+0x37/0xb0 [scsi_mod]
scsi_remove_host+0x9b/0x150 [scsi_mod]
sdebug_driver_remove+0x4b/0x150 [scsi_debug]
device_release_driver_internal+0x241/0x360
device_release_driver+0x12/0x20
bus_remove_device+0x1bc/0x290
device_del+0x259/0x580
device_unregister+0x1a/0x70
sdebug_remove_adapter+0x8b/0xf0 [scsi_debug]
scsi_debug_exit+0x76/0xe8 [scsi_debug]
__x64_sys_delete_module+0x1c1/0x280
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&shost->scan_mutex);
lock(kn->count#202);
lock(&shost->scan_mutex);
lock(kn->count#202);
*** DEADLOCK ***
2 locks held by modprobe/6539:
#0: 00000000efaf9298 (&dev->mutex){....}, at: device_release_driver_internal+0x68/0x360
#1: 00000000a6ec2c69 (&shost->scan_mutex){+.+.}, at: scsi_remove_host+0x21/0x150 [scsi_mod]
stack backtrace:
CPU: 10 PID: 6539 Comm: modprobe Not tainted 4.18.0-rc2-dbg+ #5
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.0.0-prebuilt.qemu-project.org 04/01/2014
Call Trace:
dump_stack+0xa4/0xf5
print_circular_bug.isra.34+0x213/0x221
__lock_acquire+0x1a7e/0x1b50
lock_acquire+0xd2/0x260
__kernfs_remove+0x424/0x4a0
kernfs_remove_by_name_ns+0x45/0x90
remove_files.isra.1+0x3a/0x90
sysfs_remove_group+0x5c/0xc0
sysfs_remove_groups+0x39/0x60
device_remove_attrs+0x82/0xb0
device_del+0x251/0x580
__scsi_remove_device+0x19f/0x1d0 [scsi_mod]
scsi_forget_host+0x37/0xb0 [scsi_mod]
scsi_remove_host+0x9b/0x150 [scsi_mod]
sdebug_driver_remove+0x4b/0x150 [scsi_debug]
device_release_driver_internal+0x241/0x360
device_release_driver+0x12/0x20
bus_remove_device+0x1bc/0x290
device_del+0x259/0x580
device_unregister+0x1a/0x70
sdebug_remove_adapter+0x8b/0xf0 [scsi_debug]
scsi_debug_exit+0x76/0xe8 [scsi_debug]
__x64_sys_delete_module+0x1c1/0x280
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe
See also https://www.mail-archive.com/linux-scsi@vger.kernel.org/msg54525.html.
Fixes: ac0ece9174 ("scsi: use device_remove_file_self() instead of device_schedule_callback()")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver version to 12.0.0.6
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enablement of the PBDE optimization brought out some incompatible behaviors
under error scenarios.
Best to disable and remove the PBDE optimization.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After memory allocation for the LCB response frame, the memory wasn't zero
initialized, and not all fields are set. Thus garbage shows up in the
payload.
Fix by zeroing the memory at allocation. Also properly set the Capability
field based on duration support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Performance is affected when target queue depth is tracked. An atomic
counter is incremented on the submission path which competes with it being
decremented on the completion path. In addition, multiple CPUs can
simultaniously be manipulating this counter for the same ndlp.
Reduce the overhead by only performing the target increment/decrement when
the target queue depth is less than the overall adapter depth, thus is
actually meaningful.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During remote port loss fault testing, the driver crashed with the
following trace:
general protection fault: 0000 [#1] SMP
RIP: ... lpfc_nvme_register_port+0x250/0x480 [lpfc]
Call Trace:
lpfc_nlp_state_cleanup+0x1b3/0x7a0 [lpfc]
lpfc_nlp_set_state+0xa6/0x1d0 [lpfc]
lpfc_cmpl_prli_prli_issue+0x213/0x440
lpfc_disc_state_machine+0x7e/0x1e0 [lpfc]
lpfc_cmpl_els_prli+0x18a/0x200 [lpfc]
lpfc_sli_sp_handle_rspiocb+0x3b5/0x6f0 [lpfc]
lpfc_sli_handle_slow_ring_event_s4+0x161/0x240 [lpfc]
lpfc_work_done+0x948/0x14c0 [lpfc]
lpfc_do_work+0x16f/0x180 [lpfc]
kthread+0xc9/0xe0
ret_from_fork+0x55/0x80
After registering a new remoteport, the driver is pulling an ndlp pointer
from the lpfc rport associated with the private area of a newly registered
remoteport. The private area is uninitialized, so it's garbage.
Correct by pulling the the lpfc rport pointer from the entering ndlp point,
then ndlp value from at rport. Note the entering ndlp may be replacing by
the rport->ndlp due to an address change swap.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enabling list_debug showed the drivers txcmplq was suffering list
corruption. The systems will eventually crash because the iocb free list
gets crossed linked with the prings txcmplq. Most systems will run for a
while after the corruption, but will eventually crash when a scsi eh reset
occurs and the txcmplq is attempted to be flushed. The flush gets stuck in
an endless loop.
The problem is the abort handler does not hold the sli4 ring lock while
validating the IO so the IO could complete while the driver is still
preping the abort. The erroneously generated abort, when it completes, has
pointers to the original IO that has already completed, and the IO
manipulation (for the second time) corrupts the list.
Correct by taking the ring lock early in the abort handler so the erroneous
abort won't be sent if the io has/is completing.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
CNA ports were showing speed as "unknown" even if the link is up.
Add speed decoding for FCOE-based adapters.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For ABORT_XRI_CN command, firmware identifies XRI to abort by IOTAG and RPI
combination. For ELS aborts, driver specifies IOTAG correctly but RPI is
not specified.
Fix by setting RPI in WQE.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When receiving a LOGO request we forget to clear the FC_RP_STARTED flag
before starting the rport delete routine.
As the started flag was not cleared, we're not deleting the rport but
waiting for a restart and thus are keeping the reference count of the rdata
object at 1.
This leads to the following kmemleak report:
unreferenced object 0xffff88006542aa00 (size 512):
comm "kworker/0:2", pid 24, jiffies 4294899222 (age 226.880s)
hex dump (first 32 bytes):
68 96 fe 65 00 88 ff ff 00 00 00 00 00 00 00 00 h..e............
01 00 00 00 08 00 00 00 02 c5 45 24 ac b8 00 10 ..........E$....
backtrace:
[<(____ptrval____)>] fcoe_ctlr_vn_add.isra.5+0x7f/0x770 [libfcoe]
[<(____ptrval____)>] fcoe_ctlr_vn_recv+0x12af/0x27f0 [libfcoe]
[<(____ptrval____)>] fcoe_ctlr_recv_work+0xd01/0x32f0 [libfcoe]
[<(____ptrval____)>] process_one_work+0x7ff/0x1420
[<(____ptrval____)>] worker_thread+0x87/0xef0
[<(____ptrval____)>] kthread+0x2db/0x390
[<(____ptrval____)>] ret_from_fork+0x35/0x40
[<(____ptrval____)>] 0xffffffffffffffff
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reported-by: ard <ard@kwaak.net>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
