In the case of SAE AP, drivers offload authentication to user-space
software, e.g. hostapd. For FullMAC drivers the procedure is as follows.
If auth_type is SAE and user space indicates external authentication
capability, then driver requests authentication offload to user-space
software using cfg80211_external_auth_request call. From that point,
auth frame exchange is performed transparently for driver: user-space
software sends/receives mgmt frames using mgmt_tx/mgmt_frame_register
cfg80211 callbacks. As soon as authenitcation is completed, user-space
software notifies driver about its status using external_auth cfg80211
callback.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace textual license with SPDX-License-Identifier.
Add an SPDX-License-Identifier for the Makefile.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not reject RETRY changes in driver. This decision
should belong to firmware.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Advertise WIPHY_FLAG_4ADDR_STATION capability to wireless core. Send
use4addr interface change flag to firmware in change_virtual_intf
cfg80211 callback.
In order to enable adding wireless station interface to bridge
one should turn on 4addr mode using the following command:
$ iw dev wlan0 set 4addr on
$ brctl addif br0 wlan0
If this commands succeeds, then interface can be added to bridge.
Note that when wireless interface is added to bridge, wpa_supplicant
should be started with appropriate -b <brname> parameter, e.g:
$ wpa_supplicant -Dnl80211 -iwlan0 -c/path/to/wpa.conf -b br0
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current implementation of dump_station cfg80211 callback supports
AP mode only. Add support for STA mode as well: by default in STA
mode this callback is supposed to return AP on managed interface.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware supports scan dwell time tuning for various types of scans.
Enable support for this feature:
- advertise capability to configure channel dwell time to host
- pass scan dwell parameters to wireless card in scan request
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On disconnect wireless core attempts to remove all the supported keys.
Following cfg80211_ops conventions, firmware returns -ENOENT code
for the out-of-bound key indexes. This is a normal behavior,
so no need to report errors for this case.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver retrieves information about supported extended capabilities
from wireless card. However this information is not propagated
further to Linux wireless core. Fix this by setting extended
capabilities fields of wiphy structure.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not cancel scan in disconnect callback. If there is an active scan,
it will be cancelled by firmware, then host driver will be properly
notified by event.
Cancelling scan in disconnect callback occasionally may lead to the
following race issue. Host is able to queue one scan after scan
abort in disconnect callback, and another scan after scan abort
in event handler. As a result, firmware receives second scan
before the first scan completes.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Unify command error handling using qtnf_cmd_resp_result_decode
function. Do not duplicate error messages in command handlers
and cfg80211 callbacks: report 'cmd exec fail' only on control
path internal failure. Remove redundant 'unlikely' macros.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case firmware reports that it can not do OBSS scanning for 40MHz
2.4GHz channels itself, tell userpsace to do that instead by setting
NL80211_FEATURE_NEED_OBSS_SCAN flag.
Signed-off-by: Igor mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When cfg80211 disconnect callback is triggered and command is
processed by firmware, disconnect event with local parameter
set must be sent immediately. Indicating that it's a "local"
event (not from AP) will help upper layers to process this
event correctly.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove STA connection states tracking from driver.
Leave it wireless core on host and to firmware.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/quantenna/qtnfmac/cfg80211.c: In function 'qtnf_dump_survey':
drivers/net/wireless/quantenna/qtnfmac/cfg80211.c:694:19: warning:
variable 'vif' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch implements basic WoWLAN support in qtnfmac driver, including
processing of WoWLAN features reported by firmware and implementation
of cfg80211 suspend/resume/wakeup callbacks. Currently the following
WoWLAN triggers are supported: disconnect, magic packet,
custom pattern packet.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable support for multiple SSIDs scans. Get max number of supported
SSIDs from firmware and report to cfg80211 core.
Signed-off-by: Andrey Shevchenko <ashevchenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement set_power_mgmt() callback that forwards power saving
settings to the device firmware.
Signed-off-by: Sergei Maksimenko <smaksimenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The first set of patches for 4.19. Only smaller features and bug
fixes, not really anything major. Also included are changes to
include/linux/bitfield.h, we agreed with Johannes that it makes sense
to apply them via wireless-drivers-next.
Major changes:
ath10k
* support channel 173
* fix spectral scan for QCA9984 and QCA9888 chipsets
ath6kl
* add support for Dell Wireless 1537
ti wlcore
* add support for runtime PM
* enable runtime PM autosuspend support
qtnfmac
* support changing MAC address
* enable source MAC address randomization support
libertas
* fix suspend and resume for SDIO cards
mt76
* add software DFS radar pattern detector for mt76x2 based devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbVgnkAAoJEG4XJFUm622b/DAH/0wmjFQrt1qe/goZ4igZOC5z
TTqPUmv7HO4PbHV6mU5yOFGsRCaGDo1cTyEeoiaYNGH6bQLzzJZeQORkuPQB2q5S
BCwlaET7F2iSmk8hx7eboONyVDm5v2+g6NMHBoikVFz1wZ13kCVa4sHkokUJKYB9
XNw3B2OiarPv9i37DlY3woMlY+6VMQh8J6GiB9cJSa4Xs+7l1aQCdQRP03SabI71
gLBEsW+bEVZrUdJGB5cZ8c6LmukmRQMDKMTQYUna5ZXeW1IX3ejYcQGHzzCZoKJS
LPUmisz4014r5aBzXIu3ctVn4LnVhMS5ms0EH1A6IX3vx8G9QynqH5lm9VQ1OXI=
=kWW/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-07-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.19
The first set of patches for 4.19. Only smaller features and bug
fixes, not really anything major. Also included are changes to
include/linux/bitfield.h, we agreed with Johannes that it makes sense
to apply them via wireless-drivers-next.
Major changes:
ath10k
* support channel 173
* fix spectral scan for QCA9984 and QCA9888 chipsets
ath6kl
* add support for Dell Wireless 1537
ti wlcore
* add support for runtime PM
* enable runtime PM autosuspend support
qtnfmac
* support changing MAC address
* enable source MAC address randomization support
libertas
* fix suspend and resume for SDIO cards
mt76
* add software DFS radar pattern detector for mt76x2 based devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable support for source MAC address randomization of probe request
frames. Pass addr/mask randomization parameters to firmware.
Signed-off-by: Andrey Shevchenko <ashevchenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case *vif* is NULL at 655: if (!vif), the execution path jumps to
label out, where *vif* is dereferenced at 679:
if (vif->sta_state == QTNF_STA_CONNECTING)
Fix this by immediately returning when *vif* is NULL instead of
jumping to label out.
Addresses-Coverity-ID: 1469567 ("Dereference after null check")
Fixes: 480daa9cb6 ("qtnfmac: fix invalid STA state on EAPOL failure")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quanenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver switches vif sta_state into QTNF_STA_CONNECTING when cfg80211
core initiates connect procedure. Further this state is changed either
to QTNF_STA_CONNECTED or to QTNF_STA_DISCONNECTED by BSS_JOIN and
BSS_LEAVE events from firmware. However it is possible that no such
events will be sent by firmware, e.g. if EAPOL timed out.
In this case vif sta_mode will remain in QTNF_STA_CONNECTING state and
all subsequent connection attempts will fail with -EBUSY error code.
Fix this by perfroming STA state transition from QTNF_STA_CONNECTING
to QTNF_STA_DISCONNECTED in cfg80211 disconnect callback.
No need to rely upon firmware events in this case.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver uses statically allocated wdev structures for each virtual
interface. However wdev structure is not properly cleaned up between
its uses. As a result, various bugs appear when userspace tools
like hostapd were not gracefully stopped.
In particular, this commit fixes the following issue:
- start hostapd with more than 2 mBSS
- kill hostapd using SIGKILL
- start again hostapd with more than 2 mBSS
However only two mBSS entities will be started: primary
and the last BSS listed in hostapd config.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Shorten line lengths using a more compact notation to access mac info.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
DFS offload support implemented:
- DFS_OFFLOAD feature is advertised depending on HW capabilities
- CAC_STARTED event forwarding from HW implemented
- start_radar_detection() callback now returning -ENOTSUPP
if DFS_OFFLOAD is enabled
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function qtnf_scan_done makes use of mutexes which is wrong
since it may be called from timer context. Move scan timeout
handler from timer to deferred work.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
STA does not reconnect to the same AP after disconnect. The reason is
that STA is marked as disconnected in cfg80211 disconnect callback.
This is too early since in this case qtnfmac event handler skips
cfg80211_disconnected call when processing disconnect event from
the card. As a result, wdev is left in an inconsistent state.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Validate new interface combinations using wireless core checks when new
interface is added or when the type of existing interface is modified.
This is performed to make sure that new interface combination is supported
by hardware. As a result, invalid interface combinations are rejected early,
rather than passed to hardware with sometimes unpredictable results.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Update existing code handling configuration of supported interface
combinations. Current implementation is not complete since it does
not report multiple interface combinations which are incompatible
with each other. Instead current implementation packs all the
supported combinations into single entry.
In fact currently qsr10g wireless card supports the following
two distinct interface combinations:
1. STA/repeater: 1 STA and/or 1 AP
{
{ .max = 1, .types = NL80211_IFTYPE_AP},
{ .max = 1, .types = NL80211_IFTYPE_STA},
}
2. AP/mBSS
{
{ .max = 8, .types = NL80211_IFTYPE_AP},
}
The list of supported configuration is reported by firmware during
wireless card bring-up. Communication protocol between firmware
and host has been updated accordingly in order to accommodate passing
multiple interface combination entries.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable reporting of qtnfmac hardware and firmware details
using ethtool command.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Virtual interface should be deleted after calling unregister_netdevice
since this function ends up with sending updown_intf command to card.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This allows a running AP to blacklist STAs by their MAC addresses
respecting the configured policy (either accept or deny unless listed).
It can be setup on .start_ap or with .set_mac_acl commands.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Keep generation in per-VIF data structure and increment it whenever STA
list is changed. Use generation value to fill struct station_info when
required.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Parameters passed into .mgmt_tx callback may have a NULL channel in case
userspace wants to send a frame on current channel. Make sure this case
is handled, pass "freq==0" in case channel is not specififed to tell
wlan device to use current channel.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To mimic mac80211 behaviour, change default interface type from AP to STA.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement two parts of radar handling logic:
- cfg80211 .start_radar_detect callback to allow nl80211 to initiate CAC
- radar event to allow wlan device to advertize CAC and radar events
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Center frequency is not enough to describe the channel in HT and VHT
modes. For 40MHz and 80MHz channels both primary channel and center
frequency should be specified in order to qualify channel completely.
This change adds primary channel info into qlink_chandef structure.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is possible that regulatory notifier is called before MAC data
was allocated. We need to verify that MAC data exists before trying
to send a regulatory change event.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With all callbacks converted, and the timer callback prototype
switched over, the TIMER_FUNC_TYPE cast is no longer needed,
so remove it. Conversion was done with the following scripts:
perl -pi -e 's|\(TIMER_FUNC_TYPE\)||g' \
$(git grep TIMER_FUNC_TYPE | cut -d: -f1 | sort -u)
perl -pi -e 's|\(TIMER_DATA_TYPE\)||g' \
$(git grep TIMER_DATA_TYPE | cut -d: -f1 | sort -u)
The now unused macros are also dropped from include/linux/timer.h.
Signed-off-by: Kees Cook <keescook@chromium.org>
Current logic artificially divides "start AP" procedure into three
stages:
- generic interface configuration (security, channel etc)
- IE's processing
- enable AP mode on interface
This separation would not allow to do a proper device configuration as
first stage needs to use information from IEs that are processed on
a second stage. Which means first and second stages have to be meged.
In that case there is no point anymore to keep third stage either, so
merge all three into a single command.
This new command carries all the same info as contained in
"struct cfg80211_ap_settings".
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Data contained within "Append IEs" command (QLINK_CMD_MGMT_SET_APPIE)
duplicates QTN_TLV_ID_IE_SET TLV. Convert the command to use that TLV
instead.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Supported WiFi operation modes are now identified per-band based on
HT/VHT capabilities of each band.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Information on which HT/VHT capabilities can be overridden is reported
per-MAC by wireless device.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HT/VHT capabilities must be reported per each band supported by a radio,
not for all bands on a radio. Furthermore, driver better not assume
any capabilities and just use whetever is reported by device itself.
To support this, convert "get channels" command into "get band info"
command. Difference is that it may also carry HT/VHT capabilities along
with channels information.
While at it, also add "num_bitrates" field to "get band info" command,
for future use.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wireless device may implement a logic to kick-out STA due to inactivity
for a certain period of time. This feature needs to be advertised to
higher layers if supported. Timeout value is still taken from
parameters to START_AP command, nothing changes here.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Support registration for more mgmt frame types
for debug and monitoring purposes.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Igor Mitsyanko <imitsyanko@quantenna.com>
Cc: Avinash Patil <avinashp@quantenna.com>
Cc: Sergey Matyukevich <smatyukevich@quantenna.com>
Cc: Kamlesh Rath <krath@quantenna.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Linux Wireless device structure already has current channel
information that can be used when needed. Start using it.
Since driver's channel info is not used anymore, remove it.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This cached state is used only once immediately after it is
initilized, except for BSSID value that is used for events processing.
There is no reason in keeping unused data in driver's state.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
