EMMC can have two voltage supplies, Vcc and VccQ
which are implemented in the code as consumer
supplies vmmc and vmmc_aux.
If the regulator that supplies vmmc_aux is shared
with other consumers, then sending it to sleep
will disrupt those consumers. However, the
TWL4030-family regulators may have OFF remapped
to SLEEP, in which case 'regulator_disable()'
will put the regulator to sleep only when all
consumers are disabled - which is the desired
behaviour.
This patch adds a platform data field to allow
that option.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
An eMMC may be always powered on, so that the lowest
power saving state possible is sleeping. Add a field
to the platform data to indicate that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It has been discovered that, when eMMC is powered off, current
will flow from OMAP eMMC data pull-ups to the eMMC voltage supply.
Configuring pads for OMAP off-mode does not help because eMMC is
powered off independently of OMAP off-mode. Hence the pads are
now re-configured when eMMC is powered on or off.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves the setup code for GPIO's and Voltage
Regulators from the board file mmc-twl4030.c to the
driver omap_hsmmc.c. PBIAS and other system control
configuration remains in the board file.
Moving GPIO code to the driver makes the board initialisation
code independent of when GPIO's are defined. That makes the
board initialisation now entirely independent of its original
twl4030 roots.
Moving Voltage Regulator code to the driver allows for further
development of regulator support in the core MMC code. It also
permits the MMC core to be compiled as a module, because the
board code no longer calls MMC core functions.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds 'board-sdp-flash.c', which could be utilized
by boards similar to 3430SDP. (For ex: 2430sdp, 36030sdp).
This file does initialization for all three flash devices present
in SDP boards (NOR, NAND, OneNAND), by finding there 'cs' number
dynamically using switch setting information (S8: 1-4).
This also expects partition information from core board files (for
ex: board-3430sdp.c). Which allows to choose different default
partitions for different boards.
A new structure is created for this purpose: 'flash_partitions'
in 'mach/board-sdp.h'. This has two members:
1. struct mtd_partition *parts
2. int nr_parts
A board file is expected to fill this structure and pass it to
'sdp-flsash-init'. Partition information should be passed in
structure array of 'flash_partitions'. Partition information should
be passed in below sequence in array:
NOR
OneNAND
NAND
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Introducing 'gpmc-nand.c' for GPMC specific NAND init.
For example: GPMC timing parameters and all.
This patch also migrates gpmc related calls from 'nand/omap2.c'
to 'gpmc-nand.c'.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Determine cache size required per McBSP port at init time, based on
processor type running on.
Allocate space for storing cached copies of McBSP register values at
port request.
Modify omap_msbcp_write() function to update the cache with every
register write operation.
Modify omap_mcbsp_read() to support reading from cache or hardware.
Update MCBSP_READ() macro for modified omap_mcbsp_read() function API.
Introduce a new macro that reads from the cache.
Tested on OMAP1510 based Amstrad Delta using linux-omap for-next, commit
fb7380d70e041e4b3892f6b19dff7efb609d15a4 (2.6.33-rc3+ dated 2010-01-11).
Compile-tested with: omap_perseus2_730_defconfig, omap_generic_1610_defconfig,
omap_generic_2420_defconfig, omap_2430sdp_defconfig, omap_3430sdp_defconfig,
omap_4430sdp_defconfig with CONFIG_OMAP_MCBSP=y selected.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert OMAP based boards to use physmap-flash. Refreshed against today's
Linux omap kernel tree
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we can include it easily as needed also for .S files.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define arch_decomp_setup() the same way as some other
architectures do. Use arch_id to configure the debug uart
based on the machine_is by storing it into the uart
scratchpad register for DEBUG_LL code to use.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we don't have conflicts with the defines
with compiling in multiple omaps. Set the addresses
for uarts in struct omap_globals for the early serial
init code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename and export dsi_vc_enable_hs() so that the display drivers can
control the mode of the DSI link.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Some HW blocks have errata which requires specific slave idle mode
under certain conditions.
This patch adds an hwmod API to allow setting slave idlemode
ensuring that any SYSCONFIG register updates go through hwmod.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
First, this patch adds new worst-case latency values to the
omap_device_pm_latency struct. Here the worst-case measured latencies
for the activate and deactivate hooks are stored.
In addition, add an option to auto-adjust the latency values used for
device activate/deactivate.
By setting a new 'OMAP_DEVICE_LATENCY_AUTO_ADJUST' flag in the
omap_device_pm_latency struct, the omap_device layer automatically
adjusts the activate/deactivate latencies to the worst-case measured
values.
Anytime a new worst-case value is found, it is printed to the console.
Here is an example log during boot using UART2 s an example. After
boot, the OPP is manually changed to the 125MHz OPP:
[...]
Freeing init memory: 128K
omap_device: serial8250.2: new worst case deactivate latency 0: 30517
omap_device: serial8250.2: new worst case activate latency 0: 30517
omap_device: serial8250.2: new worst case activate latency 0: 218139648
omap_device: serial8250.2: new worst case deactivate latency 0: 61035
omap_device: serial8250.2: new worst case activate latency 0: 278076171
omap_device: serial8250.2: new worst case activate latency 0: 298614501
omap_device: serial8250.2: new worst case activate latency 0: 327331542
/ # echo 125000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_setspeed
omap_device: serial8250.2: new worst case deactivate latency 0: 91552
Motivation: this can be used as a technique to automatically determine
the worst case latency values. The current method of printing a
warning on every violation is too noisy to actually interact the
console in order to set low OPP to discover latencies.
Another motivation for this patch is that the activate/deactivate
latenices can vary depending on the idlemode of the device. While
working on the UARTs, I noticed that when using no-idle, the activate
latencies were as high as several hundred msecs as shown above. When
the UARTs are in smart-idle, the max latency is well under 100 usecs.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch only affects documentation; no functional changes are
included.
Clean up comments in the current clockdomain, powerdomain code and
header files. This mostly involves conversion to kerneldoc format,
although some clarifications are also included.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch rearranges the order of structure members in struct powerdomain
to avoid wasting memory due to alignment restrictions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add usecounting for wakeup and sleep dependencies. In the current
situation, if several functions add dependencies on the same
clockdomains, when the first dependency removal function is called,
the dependency will be incorrectly removed from the hardware.
Add clkdm_clear_all_wkdeps() and clkdm_clear_all_sleepdeps(), which
provide a fast and usecounting-consistent way to clear all hardware
clockdomain dependencies, since accesses to these registers can be
quite slow. pm{2,3}4xx.c has been updated to use these new functions.
The original version of this patch did not touch these files, which
previously wrote directly to the wkdep registers, and thus confused
the usecounting code. This problem was found by Kevin Hilman
<khilman@deeprootsystems.com>.
N.B.: This patch introduces one significant functional difference over
the previous pm34xx.c code: sleepdeps are now cleared during
clockdomain initialization, whereas previously they were left
untouched. This has been tested by Kevin and confirmed to work.
The original version of this patch also did not take into
consideration that some clockdomains do not have sleep or wakeup
dependency sources, which caused NULL pointer dereferences. This
problem was debugged and fixed by Kevin Hilman
<khilman@deeprootsystems.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jouni Högander <jouni.hogander@nokia.com>
OMAP clockdomains and powerdomains are currently defined statically,
only registered at boot, and never unregistered, so we can remove the
unregister function and the locking. A variant of this was originally
suggested a while ago by Dmitry Baryshkov <dbaryshkov@gmail.com>.
This version of this patch contains an additional fix from Kevin Hilman
<khilman@deeprootsystems.com> to address one of the pwrdm_for_each_nolock()
users in mach-omap2/pm-debug.c. Thanks Kevin.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Move clockdomain wakeup dependency and sleep dependency data
structures from the powerdomain layer to the clockdomain layer, where
they belong. These dependencies were originally placed in the
powerdomain layer due to unclear documentation; however, it is clear
now that these dependencies are between clockdomains. For OMAP2/3,
this is not such a big problem, but for OMAP4 this needs to be fixed.
Thanks to Benoît Cousson <b-cousson@ti.com> for his advice on this
patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
One of the OMAP1 clocks can use the fixed divisor recalculation code
introduced in the OMAP2 clock code, so rename the
omap2_fixed_divisor_recalc() function to omap_fixed_divisor_recalc()
and make it available to all OMAPs. A followup patch converts the OMAP1
clock.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add CK_* flags for the two new Sitara chips, AM3505 and AM3517, and
the OMAP34xx die shrink, OMAP36xx/OMAP37xx. Introduce a new CK_*
flag, CK_3XXX, that marks all clocks that are common to OMAP3 family
chips. CK_343X now refers to clocks that are available only on
OMAP34{1,2,3,4}0 (WTBU) and OMAP35{03,15,25,30} (any version).
At some point, the RATE_IN_* flags should be updated also.
While here, add some documentation describing the chip families
covered by these clock flags.
This patch is partially based on patches from Ranjith Lohithakshan
<ranjithl@ti.com> and Vishwanath Sripathy <vishwanath.bs@ti.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Ranjith Lohithakshan <ranjithl@ti.com>
Cc: Vishwanath Sripathy <vishwanath.bs@ti.com>
AM3517/05 has a few additional control module registers defined mainly
to control the new IP's. This patch adds support for those new registers.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Here the ".clkstctrl_reg" field is added to the clockdomain stucture
as the module offsets for OMAP4 do not map one to one for powerdomains
and clockdomains as it used to for OMAP3. Hence we need to use absolute
addresses to access the control registers. Some of the clock domains have
modules falling in the address space of PRM partition. Hence necessitating
the use of absolute adresses.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Taking care of the platform specific and common power domains with
proper checks. Also refining some Macros according to the latest
OMAP4 requirements.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
The Autogenerated OMAP4 power domain specific file (mach-omap2/powerdomains44xx.h)
is added here.
This file is auto-generated using python scripting and following is the list of the people
involved:
Paul Walmsley
Benoit Cousson
Abhijit Pagare
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Some of the OMAP4 specific chip level initialisations are taken care of.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
[paul@pwsan.com: updated to use '4430ES1' rather than simply '4430'; updated
to apply after the intervening cpu.h/id.c patch; thanks also to Tony
for catching a bug in my rewrite]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP interrupt controller goes to unknown state when there is right
combination of l3,l4 sleep/wake-up transitions, l4 autoidle in
interrupt controller and some interrupt. When this happens, interrupts
are not delivered to ARM anymore and ARM will remain in WFI (wait for
interrupt) until interrupt controller is forced to wake-up
(i.e. lauterbach).
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Suspending drivers may still generate interrupts just before their suspend is
completed. Any pending interrupts here will prevent sleep.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
We need to set the omap_chip.oc carefully for the clocks to work.
To fix this, set the omap_chip.oc in omap3_check_features() based
on the CONTROL_IDCODE and silicon revision registers.
Also add handling for 34xx es3.1.2 as es3.1 for now.
Fixes booting on at least overo board.
Based on an earlier patch by Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In the current implementation the sysconfig value is read into
_sysc_cache once and an actual update to the sysconfig register
happens only if the new value paased is differnt from the one in _sysc_cache.
_sysc_cache is updated only if _HWMOD_SYSCONFIG_LOADED is not set.
This can lead to the follwing issue if off mode is enabled in modules
which employs "always-retore" mechanism of context save and restore.
a. The module sets the sysconfig register through omap_device_enable.
Here _sysc_cache is updated with the value written to the sysconfig
register and left.
b. The power domain containig the module enters off mode and the
module context is lost.
c. The module in use becomes active and calls omap_device_enable to
enable itself. Here a read of sysconfig register does not happen
as _HWMOD_SYSCONFIG_LOADED flag is set. The value to be written
to the sysconfig register will be same as the one written in step a.
Since _sysc_cache reflects the previous written value an update
of the sysconfig register does not happen.
This means in modules which employs "always-restore" mechanism
after off , the sysconfig regsiters will never get updated.
This patch introduces a flag SYSC_NO_CACHE which if set ensures that the
sysconfig register is always read into _sysc_cache before an update is
attempted.
This flags need to be set only by modules which does not do a context save
but re-initializes the registers every time the module is accessed. This
includes modules like i2c, smartreflex etc.
Signed-off-by: Thara Gopinath <thara@ti.com>
[paul@pwsan.com: tweaked to apply on a different head, added flag comment]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
A subsequent patch adds code on OMAP2xxx to dynamically allocate the
CPUFreq frequency table in clk_init_cpufreq_table(), so for it to
avoid a leak, it will need a corresponding function to free the
memory. This patch adds clk_exit_cpufreq_table() with generic
code to call a chip-specific variant inside the clockfw_lock spinlock via
struct clk_functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 10db25fea4 causes the following
kernel messages during N800 boot (and presumably all other 2420
boards):
[ 0.000000] BUG: mapping for 0x58000000 at 0xe0000000 overlaps vmalloc space
[ 0.000000] BUG: mapping for 0x59000000 at 0xe1000000 overlaps vmalloc space
[ 0.000000] BUG: mapping for 0x5a000000 at 0xe2000000 overlaps vmalloc space
Fix by remapping the IVA memory areas somewhere outside vmalloc space.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Out of the three major OMAP2 chip types, OMAP2420, OMAP2430, and OMAP3430,
we only map the IVA on OMAP2420. The memory mapping is not shared between
OMAP2420 and OMAP2430, so it is inappropriate to label those macros as
'24XX'; this patch changes them to '2420'.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 9905a43b made struct backlight_ops const. Omap was
setting check_fb dynamically, which caused the following
compile error:
drivers/video/backlight/omap1_bl.c: In function 'omapbl_probe':
drivers/video/backlight/omap1_bl.c:142: error: assignment of read-only variable 'omapbl_ops'
Turns out pdata->check_fb is not being used, so just remove
it to fix the compile.
Cc: Emese Revfy <re.emese@gmail.com>
Cc: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 35c9049b27 added
drivers/spi/omap_spi_100k.c.
This patch add the related clocks and pin muxing
entries to make the driver work on omap7xx platforms.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for phoenix interrupt framework. New iInterrupt
status register A, B, C are introduced in Phoenix and are cleared on write.
Due to the differences in interrupt handling with respect to TWL4030,
twl6030-irq.c is created for TWL6030 PMIC
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In original implementation, the revision passed to
these macros contained revision number in lower nibble.
But, later the revision bits (OMAP_REVBITS_XX) were
defined to use omap_revision[15:08] where revision
number is containied in higher nibble.
This patch updates the macros; else incorrect revision
is detected for OMAP35xx devices.
Signed-off-by: Sanjeev Premi <premi@ti.com>
The runtime detection of OMAP3515 and OMAP3525
was reversed.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove unused data type omap_gpio_switch_config
Thereby also get rid of following sparse warnings:
arch/arm/plat-omap/include/plat/board.h :121:20:
warning: dubious bitfield without explicit `signed' or `unsigned'
arch/arm/plat-omap/include/plat/board.h :122:19:
warning: dubious bitfield without explicit `signed' or `unsigned'
arch/arm/plat-omap/include/plat/board.h :123:24:
warning: dubious bitfield without explicit `signed' or `unsigned'
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For NAND devices '2' should be used with GPMC_CONFIG1_DEVICETYPE
instead of '1'.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds new function: omap_serial_init_port(port) that can be
used to initialize only selected UARTs as serial ports. Platforms can
then in their board files call this function instead of omap_serial_init()
if they don't want to use all UARTs as serial ports.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AuxCoreBoot0 and AuxCoreBoot1 can be only accessed in secure
mode. Replace the current code with secure monitor API's to access/modify
these registers.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the OMAP4430 cpu detection. The IC rev detection is
done with hawkeye and rev. Note that rev does not map directly to
defined processor revision numbers as ES1.0 uses value 0.It also fixes
the SCM base address to read the correct ID_CODE register.
Also the cpu_is_omap44xx() and cpu_is_omap443x() correctly populated
instead of always being true
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change adds MUX pin configuration and clocks for I2C support
to OMAP 730 and 850-based devices.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change implements USB client side support into the HTC
Herald board configuration. It uses a similar, but updated
algorithm to initialize the USB as is used in the linwizard
project.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All of the LCD DMA code in plat-omap/dma.c appears to be OMAP1-only (and
apparently only is available on a subset of OMAP1 chips).
Move this code to mach-omap1/lcd_dma.c.
Tested on OMAP1510 Amstrad Delta.
Compile-tested with omap_generic_2420_defconfig.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we cannot limit new mux code to mach-omap2.
The same signal names should eventually work for other
omaps under mach-omap2.
Note that these pins don't need to be OMAP_PIN_INPUT_PULLUP,
just OMAP_PIN_INPUT is enough.
Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch defines all the clock nodes in OMAP4430
platform. All the clock node structs and the clkdev table is
autogenerated using a python script (gen_clock_tree.py)
developed by Paul Walmsley, Benoit Cousson and Rajendra Nayak.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch fixes the PRM and CM base addresses and adds
a new CM2 base address for OMAP4
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Rather than having to do a usecs = nsecs / NSECS_PER_USEC to
track latency in usecs, just track it in nanoseconds.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Following the model of to_platform_device(), add to_omap_device()
macro so a platform_device pointer can be converted into an
omap_device pointer.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Replace the existing u8 array of module MPU IRQ lines with a struct
that includes a name - similar to the existing struct
omap_hwmod_dma_info. Device drivers can then use
platform_get_resource_byname() to retrieve specific IRQs without nasty
dependencies on array ordering.
Thanks to Benoît Cousson <b-cousson@ti.com> and Kevin Hilman
<khilman@deeprootsystems.com> for feedback on this approach.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
This patch fills in the OCP_SYSCONFIG.AUTOIDLE handling in the OMAP
hwmod code.
After this patch, the hwmod code will set the module AUTOIDLE bit
(generally <module>.OCP_SYSCONFIG.AUTOIDLE) to 1 by default upon
enable. If the hwmod flag HWMOD_NO_OCP_AUTOIDLE is set, AUTOIDLE will
be set to 0 upon enable. Upon module disable, AUTOIDLE will be set to
1.
Enabling module autoidle should save some power. The only reason to
not set the OCP_SYSCONFIG.AUTOIDLE bit is if there is a bug in the
module RTL, e.g., the MPUINTC block on OMAP3.
Comments from Kevin Hilman <khilman@deeprootsystems.com> inspired this patch,
and Kevin tested an earlier version of this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Fix loop bailout off-by-one bugs reported by Juha Leppänen
<juha_motorsportcom@luukku.com>.
This second version incorporates comments from Russell King
<linux@arm.linux.org.uk>. A new macro, 'omap_test_timeout', has
been created, with cleaner code, and existing code has been converted
to use it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Juha Leppänen <juha_motorsportcom@luukku.com>
Cc: Russell King <linux@arm.linux.org.uk>
MPU power domain bank 0 bits are displayed in position of bank 1
in PWRSTS and PREPWRSTS registers. So read them from correct
position
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch rearranges the order of structure members in struct powerdomain
to avoid wasting memory due to alignment restrictions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP1 clock code currently #includes a large .h file full of static
data structures. Instead, define the data in a .c file.
Russell King <linux@arm.linux.org.uk> proposed this new arrangement:
http://marc.info/?l=linux-omap&m=125967425908895&w=2
This patch also deals with most of the flagrant checkpatch violations.
While here, separate the mpu_rate data structures out into their own
files, opp.h and opp_data.c. In the long run, these mpu_rate tables
should be replaced with OPP code.
Also includes a patch from Felipe Balbi <felipe.balbi@nokia.com> to
mark omap1_clk_functions as __initdata to avoid a section warning:
http://patchwork.kernel.org/patch/64366/
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Nishanth Menon <nm@ti.com>
The OMAP2 clock code currently #includes a large .h file full of static
data structures. Instead, define the data in a .c file.
Russell King <linux@arm.linux.org.uk> proposed this new arrangement:
http://marc.info/?l=linux-omap&m=125967425908895&w=2
This patch also deals with most of the flagrant checkpatch violations.
While here, separate the prcm_config data structures out into their own
files, opp2xxx.h and opp24{2,3}0_data.c, and only build in the OPP tables
for the target device. This should save some memory. In the long run,
these prcm_config tables should be replaced with OPP code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Nishanth Menon <nm@ti.com>
The OMAP3 clock code currently #includes a large .h file full of static
data structures. Instead, define the data in a .c file.
Russell King <linux@arm.linux.org.uk> proposed this new arrangement:
http://marc.info/?l=linux-omap&m=125967425908895&w=2
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Russell King <linux@arm.linux.org.uk>
The core files of DSS2. DSS2 commits are split a bit artificially to
make the individual commits smaller, and DSS2 doesn't compile properly
without the rest of the core commits. This shouldn't be a problem, as no
configuration uses DSS2 yet.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
VRFB rotation engine is a block in OMAP2/3 that offers 12 independent
contexts that can be used for framebuffer rotation.
Each context has a backend area of real memory, where it stores the
pixels in undisclosed format. This memory is offered to users via 4
virtual memory areas, which see the same memory area in different
rotation angles (0, 90, 180 and 270 degrees).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Add a Video RAM manager for OMAP 2 and 3 platforms. VRAM manager is used
to allocate large continuous blocks of SDRAM or SRAM. The features VRAM
manager has that are missing from dma_alloc_* functions are:
- Support for OMAP2's SRAM
- Allocate without ioremapping
- Allocate at defined physical addresses
- Allows larger VRAM area and larger allocations
The upcoming DSS2 uses VRAM manager.
VRAM area size can be defined in kernel config, board file or with
kernel boot parameters. Board file definition overrides kernel config,
and boot parameter overrides kernel config and board file.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Split arch/arm/plat-omap/include/mach/omapfb.h into two files:
include/linux/omapfb.h - ioctls etc for userspace and some kernel
stuff for board files
drivers/video/omap/omapfb.h - for omapfb internal use
This cleans up omapfb.h and also makes it easier for the upcoming new
DSS driver to co-exist with the old driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
SMS_ROT_* registers are used by VRFB rotation engine.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Added runtime programming for the differences in EHCI interface between
OMAP3EVM revisions (Rev >= E) and (Rev < E).
Changes:
- EHCI PHY reset GPIO pin is 21 on Rev >= E while Rev < E
uses GPIO pin 135.
- Rev >= E uses EHCI Vbus enable GPIO22 line.
- Rev >= E uses GPIO61 to select EHCI port either on main board or
on Mistral Daughter Card (MDC). OMAP3EVM Rev < E doesn't have
EHCI port on main board.
- Currently GPIO61 it programmed to enable EHCI port on main
board only.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Added function to differentiate between the OMAP3EVM revisions. The
chip-id of the ethernet PHY is being used for this purpose.
Rev A to D : 0x01150000
Rev >= E : 0x92200000
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch uses a tasklet implementation for
sending mailbox messages.
Signed-off-by: C A Subramaniam <subramaniam.ca@ti.com>
Signed-off-by: Ramesh Gupta G <grgupta@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Also removed from tx_data
Signed-off-by: C A Subramaniam <subramaniam.ca@ti.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds resource information of mailbox driver for
OMAP4 mailbox module. Register base address also added
Signed-off-by: C A Subramaniam <subramaniam.ca@ti.com>
Signed-off-by: Ramesh Gupta G <grgupta@ti.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All of the OMAP3 IVA physical address macros in
plat-omap/include/plat/omap34xx.h are wrong[1]:
OMAP34XX_IVA_INTC_BASE: The IVA interrupt controller does not appear
to be accessible from the L3 interconnect, and in any case is
definitely not at 0x40000000; the latter address appears to be the
internal IVA physical address base for the OMAP2420's interrupt control[2].
OMAP34XX_DSP_BASE: The section of L3 physical address space mapped to
the IVA starts at 0x5c000000, not 0x58000000.
OMAP34XX_DSP_MEM_BASE: It's not clear what this refers to, but it's not
in the L3 IVA address space.
OMAP34XX_DSP_IPI_BASE: The Intrusive Port Interface is a relic from
the OMAP2420 days and no longer applies to OMAP3.
OMAP34XX_DSP_MMU_BASE: The DSP MMU is mapped at 0x5d000000, not 0x5a000000.
Nothing that uses these can possibly be working, so drop them. When
future code needs these, correct versions can be added in.
1. OMAP34xx Multimedia Device Silicon Revision 3.1.x Rev. W, Table 2-8:
"L3 Interconnect View of the IVA2.2 Subsystem Memory Space." p. 229.
2. OMAP2420 Multimedia Processor Silicon Revision 2.1.1, 2.2 (Rev. Q),
section 2.2.4.1, "IVA Memory Space Seen by L3", p. 132.
3. ibid., section 4.3.11, "DSP IPI Overview", p. 200.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The speed ctrl bit for MMC I/O is part of CONTROL_PROG_IO1 register
in omap3630.This patch sets it up accordingly.
Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform init code for EHCI driver.
Various fixes to the original patch by Ajay Kumar Gupta <ajay.gupta@ti.com>
and Anand Gadiyar <gadiyar@ti.com>.
Overo support added by Olof Johansson <olof@lixom.net>
Beagle support added by Koen Kooi <koen@beagleboard.org>
CM-T32 support added by Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing declarations to allow the recently introduced
ehci-omap driver to build on OMAP3
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support to detect AM3505/AM3517 devices at runtime.
Also updates the CPU names printed during boot.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
3630 is getting treated like next rev of 3430
omap_chip.oc variable has to be updated for 3630 version
Otherwise the Core power domain is not getting registered.
This gets used in the registration of power domains in:
"arch/arm/mach-omap2/powerdomains34xx.h"
core_34xx_es3_1_pwrdm
OMAP_CHIP_INIT(CHIP_GE_OMAP3430ES3_1)
Core power doman will get registered for 3630 only when .oc is
populated correctly.
Tested on Zoom3(3630) board
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Alexander Shishkin <virtuoso@slind.org>
Acked-by: Ari Kauppi <kauppi@papupata.org>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP3630 is the latest in the family of OMAP3 devices
and among the changes it introduces are:
New OPP levels for new voltage and frequency levels. a bunch of
Bug fixes to various modules feature additions, notably with ISP,
sDMA etc.
Details about the chip is available here:
http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?templateId=6123&navigationId=12836&contentId=52606
Strategy used:
Strategy to introduce this device into Linux was discussed here:
Ref: http://marc.info/?t=125343303400003&r=1&w=2
Two approaches were available:
a) Consider 3630 generation of devices as a new family of silicon
b) Consider 3630 as an offshoot of 3430 family of devices
As a common consensus, (b) seems to be more valid for 3630 as:
* There are changes which are easily handled by using "FEATURES"
infrastructure.
For details how to do this, see thread:
http://marc.info/?t=125050998500001&r=1&w=2
* Most of existing 34xx infrastructure can be reused(almost 90%+)
- so no ugly if (cpu_is_omap34xx() || cpu_is_omap36xx())
all over the place
- lesser chance of bugs due to reuse of proven code flow
- 36xx specific handling can still be done where required
within the existing infrastructure
NOTE:
* If additional 34xx series are added, OMAP3430_REV_ESXXXX can be
added on top of the existing 3630 ones are renumbered
This patch was tested on SDP3430, boot tested on 3630 platform using
3430sdp defconfig
Signed-off-by: Madhusudhan Chikkature Rajashekar <madhu.cr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Cc: Allen Pais <allen.pais@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Sanjeev Premi <premi@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Sergio Alberto Aguirre Rodriguez <saaguirre@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add runtime check for these OMAP35x variations
based on the detected Si features:
OMAP3503, OMAP3515, OMAP3525 and OMA3530.
Also, delayed the call to pr_info() into actual
variant is detected in omap3_cpuinfo()
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP35x family has multiple variants differing
in the HW features. This patch detects these features
at runtime and prints information during the boot.
Since most of the code seemed repetitive, macros
have been used for readability.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The MMC mux pins normally used by omap chips in devices.c
are different from what is needed by omap7xx chips. This
change adds a conditional around the mux setup code to
enable the correct mux pins.
The omap730 and omap850 both use a different clock for the "fck"
clock of the MMC interface than other omap processors based on the
SOFT_REQ_REG, pin 12. The "ick" clock is the same as that used
by other omap processors.
* Added the missing clock definition as mmc3_ck to clock.h
* Added the clock definition to omap_clks in clock.c
* Added CK_7XX to the mmci-omap.0 "ick" clock already in clock.c
With these changes, it is now possible to initialize and use MMC
cards with omap730 and omap850 devices.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Zoom2/Zoom3 kind of boards do not use omap uarts for console.
These use external debug board for console.
So these boards should not have "Uncompressing Kernel...."
log put on omap uarts.
By interoducing OMAP_LL_DEBUG_NONE option,
unnecessary writes to omap uarts is avoided.
In future, the DEBUG_LL interface will be enhanced
to use external debug board.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eliminate OMAP_MAX_NR_PORTS
Note that also the null terminator entry for omap1
serial_platform_data needs to be now removed to avoid
oopsing.
Note that mach-omap1 uses struct plat_serial8250_port
array, which requires a null terminator at the end,
and that's why we need to use ARRAY_SIZE - 1. This
is not needed on mach-omap2 as the array used is
struct omap_uart_state, and does not use a null
terminator.
Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Due to an OMAP3 errata (1.142), on HS/EMU devices SDRC should be
programed to issue automatic self refresh on timeout
of AUTO_CNT = 1 prior to any transition to OFF mode.
This is needed only on sil rev's ES3.0 and above.
This patch enables the above needed WA in the SDRC power register
value stored in scratchpad, so that ROM code restores this value
in SDRC POWER on the wakeup path.
The original SDRC POWER register value is stored and restored back
in omap_sram_idle() function.
This fixes some random crashes observed while stressing suspend
on HS/EMU devices.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Errata: ES3.0, ES3.1 SDRC not sending auto-refresh when OMAP wakes-up
from OFF mode
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The SMS_SYSCONFIG register gets reset in off mode, added a
save/restore mechanism for that.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For HS/EMU devices, these additional features are also used:
- DMA interrupt disable routine added
- Added DMA controller reset to DMA context restore
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add context save and restore for CORE powerdomain resources in order
to support off-mode.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Generalize the copy of SRAM functions into omap_push_sram_idle()
so it can be used on init but also after off-mode transitions.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add context save and restore for the System Control Module to suport
off-mode.
ETK and debobs definitions added by Peter De Schrijver.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch populates the scratchpad contents as expected by the
bootROM code.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add context save and restore for PRCM module to support off-mode.
Additional registers (CM_CLKSEL4, CM_CLKEN, CM_CLKEN2) added by Tero
Kristo.
Missing CM_CLKEN_PLL_IVA2 register added by Kalle Jokiniemi.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add context save and restore for the INTC module to support off-mode.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add context save and restore to enable off-mode.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds the context save and restore functions for GPMC to
enable off-mode.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
Create the headers needed for compiling under
mach-omap1/include/mach and mach-omap2/include/mach.
This was done with the following script:
#!/bin/bash
mach_files="clkdev.h gpio.h hardware.h io.h irqs.h memory.h \
smp.h system.h timex.h uncompress.h vmalloc.h"
omaps="mach-omap1 mach-omap2"
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
mkdir -p $plat_dir_new
git add $plat_dir_new
for dir in $omaps; do
mach_dir_new="arch/arm/$dir/include/mach"
for header in $mach_files; do
file="$mach_dir_new/$header"
if [ ! -f $file ]; then
echo -ne "/*\n * $file\n */\n\n#include <plat/$header>\n" > $file
git add $file
if [ ! -f $plat_dir_new/$header ]; then
git mv $mach_dir_old/$header $plat_dir_new/$header
fi
fi
done
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
