The XO-1.5 does not support the ambient temperature property.
Create a separate list of properties for that configuration where
ambient temperature is not included, and apply the correct property
list at runtime.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
During test-build (with disabled 'depends on') I found that
jz4740-battery driver lacks linux/io.h, which makes build break
like this (on x86):
CC [M] drivers/power/isp1704_charger.o
jz4740-battery.c: In function 'jz_battery_read_voltage':
jz4740-battery.c:84: error: implicit declaration of function 'readw’
jz4740-battery.c: In function 'jz_battery_probe':
jz4740-battery.c:284: error: implicit declaration of function 'ioremap_nocache’
jz4740-battery.c:285: warning: assignment makes pointer from integer without a cast
jz4740-battery.c:372: error: implicit declaration of function 'iounmap'
make[2]: *** [drivers/power/jz4740-battery.o] Error 1
This patch fixes the issues, and thus makes it easier to build-test
the driver for me.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Add support for inverted gpio_charge_finished values.
This change is necessary for H1940 support.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
flush_scheduled_work() is deprecated and scheduled to be removed.
In battery drivers, the work can be canceled on probe failure and
removal and should be flushed on suspend. Replace
flush_scheduled_work() usages with direct cancels and flushes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
device_unregister() might free its argument. This leads to freed
memory use in kfree(). Also use put_device() instead of kfree()
as dev may be already used in another layer after call to device_add().
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This patch fixes a potential race between the irq handler and the probe
and remove functions.
The irq should not be requested before the chargers power_supply has been
registered and has to be freed before the power_supply is unregistered,
otherwise it is possible that the irq fires while the power_supply is not
initialized yet or has already been freed.
While we are at it replace request_irq with request_any_context_irq.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This patch sets a default name for the power_supply in case there was
no name supplied through the platform_data.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Since kzalloc can return NULL we have to check its result.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Currently platform_data is dereferenced without checking whether it
is actually set, which can lead to kernel crashes.
This patch adds a check which will abort the drivers probe function
gracefully if no platform_data is supplied.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
If the device is booted up with cable connected, or the
module is loaded after plugging in the cable, the
notification has come and gone, so not relying on it at
probe time. Instead this checks the VBUS level manually
after probe.
Signed-off-by: Heikki Krogerus <heikki.krogerus@nokia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
isp1704_test_ulpi() is the first place that needs isp->dev
member, so it must be set before calling the function.
Signed-off-by: Heikki Krogerus <heikki.krogerus@nokia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
To avoid breaking high speed chirp handshaking with CDP
chargers, no more then 500mA should be drawn. To make sure
of this, utilizing current_max property. After the device
has enumerated, it's safe to draw the maximum 1800mA as
defined in the Battery Charging Specification. This can be
also used with normal USB connection if the controller sends
ENUMERATED notification with the milliamps as data.
From now on the online property indicates VBUS, present
property if there is a charger and current_max the milliamps
possible to draw from VBUS.
Signed-off-by: Heikki Krogerus <heikki.krogerus@nokia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Model should have room to accommodate the trailing null byte,
"isp170[4|7]\0".
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Acked-by: Heikki Krogerus <heikki.krogerus@nokia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This patch adds a simple driver for chargers indicating their online
status through a GPIO pin.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
We can not handle more then one ADC request at a time to the battery.
The patch adds a mutex around the ADC read code to ensure this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: stable@kernel.org
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
A check against division by zero was modified in commit b0525b48.
Since this change time_to_empty_now is always reported as zero
while the battery is discharging and as a negative value while
the battery is charging. This is because current is negative while
the battery is discharging.
Fix the check introduced by commit b0525b48 so that time_to_empty_now
is reported correctly during discharge and as zero while charging.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Cc: stable@kernel.org [2.6.32..2.6.36]
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (w83795) Check for BEEP pin availability
hwmon: (w83795) Clear intrusion alarm immediately
hwmon: (w83795) Read the intrusion state properly
hwmon: (w83795) Print the actual temperature channels as sources
hwmon: (w83795) List all usable temperature sources
hwmon: (w83795) Expose fan control method
hwmon: (w83795) Fix fan control mode attributes
hwmon: (lm95241) Check validity of input values
hwmon: Change mail address of Hans J. Koch
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: sysfs: fix printk warnings
PCI: fix pci_bus_alloc_resource() hang, prefer positive decode
PCI: read current power state at enable time
PCI: fix size checks for mmap() on /proc/bus/pci files
x86/PCI: coalesce overlapping host bridge windows
PCI hotplug: ibmphp: Add check to prevent reading beyond mapped area
Make sure I2C adapters being registered have the required struct
fields set. If they don't, problems will happen later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It's about time to make it clear that i2c_adapter.id is deprecated.
Hopefully this will remind the last user to move over to a different
strategy.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Drivers don't need to include <linux/i2c-id.h>, especially not when
they don't use anything that header file provides.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Hunold <michael@mihu.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Delete unused I2C adapter IDs. Special cases are:
* I2C_HW_B_RIVA was still set in driver rivafb, however no other
driver is ever looking for this value, so we can safely remove it.
* I2C_HW_B_HDPVR is used in staging driver lirc_zilog, however no
adapter ID is ever set to this value, so the code in question never
runs. As the code additionally expects that I2C_HW_B_HDPVR may not
be defined, we can delete it now and let the lirc_zilog driver
maintainer rewrite this piece of code.
Big thanks for Hans Verkuil for doing all the hard work :)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit. This is obsolete meanwhile, so fix it and hope the word will spread.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The fix in commit 6b4e81db25 ("i8k: Tell gcc that *regs gets
clobbered") to work around the gcc miscompiling i8k.c to add "+m
(*regs)" caused register pressure problems and a build failure.
Changing the 'asm' statement to 'asm volatile' instead should prevent
that and works around the gcc bug as well, so we can remove the "+m".
[ Background on the gcc bug: a memory clobber fails to mark the function
the asm resides in as non-pure (aka "__attribute__((const))"), so if
the function does nothing else that triggers the non-pure logic, gcc
will think that that function has no side effects at all. As a result,
callers will be mis-compiled.
Adding the "+m" made gcc see that it's not a pure function, and so
does "asm volatile". The problem was never really the need to mark
"*regs" as changed, since the memory clobber did that part - the
problem was just a bug in the gcc "pure" function analysis - Linus ]
Signed-off-by: Jim Bos <jim876@xs4all.nl>
Acked-by: Jakub Jelinek <jakub@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On the W83795ADG, there's a single pin for BEEP and OVT#, so you
can't have both. Check the configuration and don't create beep
attributes when BEEP pin is not available.
The W83795G has a dedicated BEEP pin so the functionality is always
available there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
When asked to clear the intrusion alarm, do so immediately. We have to
invalidate the cache to make sure the new status will be read. But we
also have to read from the status register once to clear the pending
alarm, as writing to CLR_CHS surprising won't clear it automatically.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
We can't read the intrusion state from the real-time alarm registers
as we do for all other alarm flags, because real-time alarm bits don't
stick (by definition) and the intrusion state has to stick until
explicitly cleared (otherwise it has little value.)
So we have to use the interrupt status register instead, which is read
from the same address but with a configuration bit flipped in another
register.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Don't expose raw register values to user-space. Decode and encode
temperature channels selected as temperature sources as needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Temperature sources are not correlated directly with temperature
channels. A look-up table is required to find out which temperature
sources can be used depending on which temperature channels (both
analog and digital) are enabled.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Expose fan control method (DC vs. PWM) using the standard sysfs
attributes. I've made it read-only as the board should be wired for
a given mode, the BIOS should have set up the chip for this mode, and
you shouldn't have to change it. But it would be easy enough to make
it changeable if someone comes up with a use case.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
There were two bugs:
* Speed cruise mode was improperly reported for all fans but fan1.
* Fan control method (PWM vs. DC) was mixed with the control mode.
It will be added back as a separate attribute, as per the standard
sysfs interface.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
This clears the following build-time warnings I was seeing:
drivers/hwmon/lm95241.c: In function "set_interval":
drivers/hwmon/lm95241.c:132:15: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max2":
drivers/hwmon/lm95241.c:278:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max1":
drivers/hwmon/lm95241.c:277:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min2":
drivers/hwmon/lm95241.c:249:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min1":
drivers/hwmon/lm95241.c:248:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type2":
drivers/hwmon/lm95241.c:220:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type1":
drivers/hwmon/lm95241.c:219:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
This also fixes a small race in set_interval() as a side effect: by
working with a temporary local variable we prevent data->interval from
being accessed at a time it contains the interval value in the wrong
unit.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Davide Rizzo <elpa.rizzo@gmail.com>
My old mail address doesn't exist anymore. This changes all occurrences
to my new address.
Signed-off-by: Hans J. Koch <hjk@hansjkoch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cast pci_resource_start() and pci_resource_len() to u64 for printk.
drivers/pci/pci-sysfs.c:753: warning: format '%16Lx' expects type 'long long unsigned int', but argument 9 has type 'resource_size_t'
drivers/pci/pci-sysfs.c:753: warning: format '%16Lx' expects type 'long long unsigned int', but argument 10 has type 'resource_size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6:
fsl-diu-fb: drop dead ioctl define
MAINTAINERS: Add an fbdev git tree entry.
OMAP: DSS: Fix documentation regarding 'vram' kernel parameter
OMAP: VRAM: Fix boot-time memory allocation
OMAP: VRAM: improve VRAM error prints
sisfb: limit POST memory test according to PCI resource length
fbdev: sh_mobile_lcdc: use correct number of modes, when using the default
fbdev: sh_mobile_lcdc: use the standard CEA-861 720p timing
fbdev: sh_mobile_hdmi: properly clean up modedb on monitor unplug
The radix tree retry logic got a bit of an overhaul and subsequently
broke the virtual IRQ subgroup build. Simply switch over to
radix_tree_deref_retry() as per the filemap changes, which the virq
lookup logic was modelled after in the first place.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
More recent GCC caused the i8k driver to stop working, on Slackware
compiler was upgraded from gcc-4.4.4 to gcc-4.5.1 after which it didn't
work anymore, meaning the driver didn't load or gave total nonsensical
output.
As it turned out the asm(..) statement forgot to mention it modifies the
*regs variable.
Credits to Andi Kleen and Andreas Schwab for providing the fix.
Signed-off-by: Jim Bos <jim876@xs4all.nl>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we have:
--w--w--w-. 1 root root 0 2010-11-11 14:56 /sys/kernel/debug/acpi/custom_method
which is just crazy. Change this to --w-------.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: stable@kernel.org (for 2.6.36)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (66 commits)
can-bcm: fix minor heap overflow
gianfar: Do not call device_set_wakeup_enable() under a spinlock
ipv6: Warn users if maximum number of routes is reached.
docs: Add neigh/gc_thresh3 and route/max_size documentation.
axnet_cs: fix resume problem for some Ax88790 chip
ipv6: addrconf: don't remove address state on ifdown if the address is being kept
tcp: Don't change unlocked socket state in tcp_v4_err().
x25: Prevent crashing when parsing bad X.25 facilities
cxgb4vf: add call to Firmware to reset VF State.
cxgb4vf: Fail open if link_start() fails.
cxgb4vf: flesh out PCI Device ID Table ...
cxgb4vf: fix some errors in Gather List to skb conversion
cxgb4vf: fix bug in Generic Receive Offload
cxgb4vf: don't implement trivial (and incorrect) ndo_select_queue()
ixgbe: Look inside vlan when determining offload protocol.
bnx2x: Look inside vlan when determining checksum proto.
vlan: Add function to retrieve EtherType from vlan packets.
virtio-net: init link state correctly
ucc_geth: Fix deadlock
ucc_geth: Do not bring the whole IF down when TX failure.
...
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (28 commits)
Revert "USB: xhci: Use GFP_ATOMIC under spin_lock"
USB: ohci-jz4740: Fix spelling in MODULE_ALIAS
UWB: Return UWB_RSV_ALLOC_NOT_FOUND rather than crashing on NULL dereference if kzalloc fails
usb: core: fix information leak to userland
usb: misc: iowarrior: fix information leak to userland
usb: misc: sisusbvga: fix information leak to userland
usb: subtle increased memory usage in u_serial
USB: option: fix when the driver is loaded incorrectly for some Huawei devices.
USB: xhci: Use GFP_ATOMIC under spin_lock
usb: gadget: goku_udc: add registered flag bit, fixing build
USB: ehci/mxc: compile fix
USB: Fix FSL USB driver on non Open Firmware systems
USB: the development of the usb tree is now in git
usb: musb: fail unaligned DMA transfers on v1.8 and above
USB: ftdi_sio: add device IDs for Milkymist One JTAG/serial
usb.h: fix ioctl kernel-doc info
usb: musb: gadget: kill duplicate code in musb_gadget_queue()
usb: musb: Fix handling of spurious SESSREQ
usb: musb: fix kernel oops when loading musb_hdrc module for the 2nd time
USB: musb: blackfin: push clkin value to platform resources
...
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
n_gsm: Fix length handling
n_gsm: Copy n2 over when configuring via ioctl interface
serial: bfin_5xx: grab port lock before making port termios changes
serial: bfin_5xx: disable CON_PRINTBUFFER for consoles
serial: bfin_5xx: remove redundant SSYNC to improve TX speed
serial: bfin_5xx: always include DMA headers
vcs: make proper usage of the poll flags
amiserial: Remove unused variable icount
8250: Fix tcsetattr to avoid ioctl(TIOCMIWAIT) hang
tty_ldisc: Fix BUG() on hangup
TTY: restore tty_ldisc_wait_idle
SERIAL: blacklist si3052 chip
drivers/serial/bfin_5xx.c: Fix line continuation defects
tty: prevent DOS in the flush_to_ldisc
8250: add support for Kouwell KW-L221N-2
nozomi: Fix warning from the previous TIOCGCOUNT changes
tty: fix warning in synclink driver
tty: Fix formatting in tty.h
tty: the development tree is now done in git
* 'upstream/core' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: do not release any memory under 1M in domain 0
xen: events: do not unmask event channels on resume
xen: correct size of level2_kernel_pgt
