Save number of file system errors, and the time function name, line
number, block number, and inode number of the first and most recent
errors reported on the file system in the superblock.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The nobh option was only supported for writeback mode, but given that all
write paths actually create buffer heads it effectively was a no-op already.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
We don't need to set s_dirt in most of the ext4 code when journaling
is enabled. In ext3/4 some of the summary statistics for # of free
inodes, blocks, and directories are calculated from the per-block
group statistics when the file system is mounted or unmounted. As a
result the superblock doesn't have to be updated, either via the
journal or by setting s_dirt. There are a few exceptions, most
notably when resizing the file system, where the superblock needs to
be modified --- and in that case it should be done as a journalled
operation if possible, and s_dirt set only in no-journal mode.
This patch will optimize out some unneeded disk writes when using ext4
with a journal.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Add a new ext4 state to tell us when a file has been newly created; use
that state in ext4_sync_file in no-journal mode to tell us when we need
to sync the parent directory as well as the inode and data itself. This
fixes a problem in which a panic or power failure may lose the entire
file even when using fsync, since the parent directory entry is lost.
Addresses-Google-Bug: #2480057
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
struct ext4_new_group_input needs to be converted because u64 has
only 32-bit alignment on some 32-bit architectures, notably i386.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
It is unnecessary, and in general impossible, to define the compat
ioctl numbers except when building the filesystem with CONFIG_COMPAT
defined.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
At several places we modify EXT4_I(inode)->i_flags without holding
i_mutex (ext4_do_update_inode, ...). These modifications are racy and
we can lose updates to i_flags. So convert handling of i_flags to use
bitops which are atomic.
https://bugzilla.kernel.org/show_bug.cgi?id=15792
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
EXT4_ERROR_INODE() tends to provide better error information and in a
more consistent format. Some errors were not even identifying the inode
or directory which was corrupted, which made them not very useful.
Addresses-Google-Bug: #2507977
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Jack up ext4_get_blocks() and add a new function, ext4_map_blocks()
which uses a much smaller structure, struct ext4_map_blocks which is
20 bytes, as opposed to a struct buffer_head, which nearly 5 times
bigger on an x86_64 machine. By switching things to use
ext4_map_blocks(), we can save stack space by using ext4_map_blocks()
since we can avoid allocating a struct buffer_head on the stack.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This adds a new field in ext4_group_info to cache the largest available
block range in a block group; and don't load the buddy pages until *after*
we've done a sanity check on the block group.
With large allocation requests (e.g., fallocate(), 8MiB) and relatively full
partitions, it's easy to have no block groups with a block extent large
enough to satisfy the input request length. This currently causes the loop
during cr == 0 in ext4_mb_regular_allocator() to load the buddy bitmap pages
for EVERY block group. That can be a lot of pages. The patch below allows
us to call ext4_mb_good_group() BEFORE we load the buddy pages (although we
have check again after we lock the block group).
Addresses-Google-Bug: #2578108
Addresses-Google-Bug: #2704453
Signed-off-by: Curt Wohlgemuth <curtw@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
* 'write_inode2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
pass writeback_control to ->write_inode
make sure data is on disk before calling ->write_inode
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (36 commits)
ext4: fix up rb_root initializations to use RB_ROOT
ext4: Code cleanup for EXT4_IOC_MOVE_EXT ioctl
ext4: Fix the NULL reference in double_down_write_data_sem()
ext4: Fix insertion point of extent in mext_insert_across_blocks()
ext4: consolidate in_range() definitions
ext4: cleanup to use ext4_grp_offs_to_block()
ext4: cleanup to use ext4_group_first_block_no()
ext4: Release page references acquired in ext4_da_block_invalidatepages
ext4: Fix ext4_quota_write cross block boundary behaviour
ext4: Convert BUG_ON checks to use ext4_error() instead
ext4: Use direct_IO_no_locking in ext4 dio read
ext4: use ext4_get_block_write in buffer write
ext4: mechanical rename some of the direct I/O get_block's identifiers
ext4: make "offset" consistent in ext4_check_dir_entry()
ext4: Handle non empty on-disk orphan link
ext4: explicitly remove inode from orphan list after failed direct io
ext4: fix error handling in migrate
ext4: deprecate obsoleted mount options
ext4: Fix fencepost error in chosing choosing group vs file preallocation.
jbd2: clean up an assertion in jbd2_journal_commit_transaction()
...
This gives the filesystem more information about the writeback that
is happening. Trond requested this for the NFS unstable write handling,
and other filesystems might benefit from this too by beeing able to
distinguish between the different callers in more detail.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
There are duplicate macro definitions of in_range() in mballoc.h and
balloc.c. This consolidates these two definitions into ext4.h, and
changes extents.c to use in_range() as well.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Andreas Dilger <adilger@sun.com>
Convert a bunch of BUG_ONs to emit a ext4_error() message and return
EIO. This is a first pass and most notably does _not_ cover
mballoc.c, which is a morass of void functions.
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Allocate uninitialized extent before ext4 buffer write and
convert the extent to initialized after io completes.
The purpose is to make sure an extent can only be marked
initialized after it has been written with new data so
we can safely drop the i_mutex lock in ext4 DIO read without
exposing stale data. This helps to improve multi-thread DIO
read performance on high-speed disks.
Skip the nobh and data=journal mount cases to make things simple for now.
Signed-off-by: Jiaying Zhang <jiayingz@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This commit renames some of the direct I/O's block allocation flags,
variables, and functions introduced in Mingming's "Direct IO for holes
and fallocate" patches so that they can be used by ext4's buffered
write path as well. Also changed the related function comments
accordingly to cover both direct write and buffered write cases.
Signed-off-by: Jiaying Zhang <jiayingz@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
fallocate() may potentially instantiate blocks past EOF, depending
on the flags used when it is called.
e2fsck currently has a test for blocks past i_size, and it
sometimes trips up - noticeably on xfstests 013 which runs fsstress.
This patch from Jiayang does fix it up - it (along with
e2fsprogs updates and other patches recently from Aneesh) has
survived many fsstress runs in a row.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Jiaying Zhang <jiayingz@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Add __percpu sparse annotations to fs.
These annotations are to make sparse consider percpu variables to be
in a different address space and warn if accessed without going
through percpu accessors. This patch doesn't affect normal builds.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Alex Elder <aelder@sgi.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Just a pet peeve of mine; we had a mishash of calls with either __func__
or "function_name" and the latter tends to get out of sync.
I think it's easier to just hide the __func__ in a macro, and it'll
be consistent from then on.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
At several places we modify EXT4_I(inode)->i_state without holding
i_mutex (ext4_release_file, ext4_bmap, ext4_journalled_writepage,
ext4_do_update_inode, ...). These modifications are racy and we can
lose updates to i_state. So convert handling of i_state to use bitops
which are atomic.
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
We should update reserve space if it is delalloc buffer
and that is indicated by EXT4_GET_BLOCKS_DELALLOC_RESERVE flag.
So use EXT4_GET_BLOCKS_DELALLOC_RESERVE in place of
EXT4_GET_BLOCKS_UPDATE_RESERVE_SPACE
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
When we fallocate a region of the file which we had recently written,
and which is still in the page cache marked as delayed allocated blocks
we need to make sure we don't do the quota update on writepage path.
This is because the needed quota updated would have already be done
by fallocate.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
In the past, ext4_calc_metadata_amount(), and its sub-functions
ext4_ext_calc_metadata_amount() and ext4_indirect_calc_metadata_amount()
badly over-estimated the number of metadata blocks that might be
required for delayed allocation blocks. This didn't matter as much
when functions which managed the reserved metadata blocks were more
aggressive about dropping reserved metadata blocks as delayed
allocation blocks were written, but unfortunately they were too
aggressive. This was fixed in commit 0637c6f, but as a result the
over-estimation by ext4_calc_metadata_amount() would lead to reserving
2-3 times the number of pending delayed allocation blocks as
potentially required metadata blocks. So if there are 1 megabytes of
blocks which have been not yet been allocation, up to 3 megabytes of
space would get reserved out of the user's quota and from the file
system free space pool until all of the inode's data blocks have been
allocated.
This commit addresses this problem by much more accurately estimating
the number of metadata blocks that will be required. It will still
somewhat over-estimate the number of blocks needed, since it must make
a worst case estimate not knowing which physical blocks will be
needed, but it is much more accurate than before.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This patch also fixes write vs chown race condition.
Acked-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Add checks to ext4_free_branches() to make sure a block number found
in an indirect block are valid before trying to free it. If a bad
block number is found, stop freeing the indirect block immediately,
since the file system is corrupt and we will need to run fsck anyway.
This also avoids spamming the logs, and specifically avoids
driver-level "attempt to access beyond end of device" errors obscure
what is really going on.
If you get *really*, *really*, *really* unlucky, without this patch, a
supposed indirect block containing garbage might contain a reference
to a primary block group descriptor, in which case
ext4_free_branches() could end up zero'ing out a block group
descriptor block, and if then one of the block bitmaps for a block
group described by that bg descriptor block is not in memory, and is
read in by ext4_read_block_bitmap(). This function calls
ext4_valid_block_bitmap(), which assumes that bg_inode_table() was
validated at mount time and hasn't been modified since. Since this
assumption is no longer valid, it's possible for the value
(ext4_inode_table(sb, desc) - group_first_block) to go negative, which
will cause ext4_find_next_zero_bit() to trigger a kernel GPF.
Addresses-Google-Bug: #2220436
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The "offset" member in ext4_io_end holds bytes, not blocks, so
ext4_lblk_t is wrong - and too small (u32).
This caused the async i/o writes to sparse files beyond 4GB to fail
when they wrapped around to 0.
Also fix up the type of arguments to ext4_convert_unwritten_extents(),
it gets ssize_t from ext4_end_aio_dio_nolock() and
ext4_ext_direct_IO().
Reported-by: Giel de Nijs <giel@vectorwise.com>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
We cannot rely on buffer dirty bits during fsync because pdflush can come
before fsync is called and clear dirty bits without forcing a transaction
commit. What we do is that we track which transaction has last changed
the inode and which transaction last changed allocation and force it to
disk on fsync.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Add the facility for ext4_forget() to be called from
ext4_free_blocks(). This simplifies the code in a large number of
places, and centralizes most of the work of calling ext4_forget() into
a single place.
Also fix a bug in the extents migration code; it wasn't calling
ext4_forget() when releasing the indirect blocks during the
conversion. As a result, if the system cashed during or shortly after
the extents migration, and the released indirect blocks get reused as
data blocks, the journal replay would corrupt the data blocks. With
this new patch, fixing this bug was as simple as adding the
EXT4_FREE_BLOCKS_FORGET flags to the call to ext4_free_blocks().
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
ext4_mb_free_blocks() is only called by ext4_free_blocks(), and the
latter function doesn't really do much. So merge the two functions
together, such that ext4_free_blocks() is now found in
fs/ext4/mballoc.c. This saves about 200 bytes of compiled text space.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The ext4_forget() function better belongs in ext4_jbd2.c. This will
allow us to do some cleanup of the ext4_journal_revoke() and
ext4_journal_forget() functions, as well as giving us better error
reporting since we can report the caller of ext4_forget() when things
go wrong.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
It is anticipated that when sb_issue_discard starts doing
real work on trim-capable devices, we may see issues. Make
this mount-time optional, and default it to off until we know
that things are working out OK.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
At the end of direct I/O operation, ext4_ext_direct_IO() always called
ext4_convert_unwritten_extents(), regardless of whether there were any
unwritten extents involved in the I/O or not.
This commit adds a state flag so that ext4_ext_direct_IO() only calls
ext4_convert_unwritten_extents() when necessary.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This reverts commit d0646f7b63, as
requested by Eric Sandeen.
It can basically cause an ext4 filesystem to miss recovery (and thus get
mounted with errors) if the journal checksum does not match.
Quoth Eric:
"My hand-wavy hunch about what is happening is that we're finding a
bad checksum on the last partially-written transaction, which is
not surprising, but if we have a wrapped log and we're doing the
initial scan for head/tail, and we abort scanning on that bad
checksum, then we are essentially running an unrecovered filesystem.
But that's hand-wavy and I need to go look at the code.
We lived without journal checksums on by default until now, and at
this point they're doing more harm than good, so we should revert
the default-changing commit until we can fix it and do some good
power-fail testing with the fixes in place."
See
http://bugzilla.kernel.org/show_bug.cgi?id=14354
for all the gory details.
Requested-by: Eric Sandeen <sandeen@redhat.com>
Cc: Theodore Tso <tytso@mit.edu>
Cc: Alexey Fisher <bug-track@fisher-privat.net>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Mathias Burén <mathias.buren@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"Looking at ext4.h, I think the setting of extra time fields forgets to
mask the epoch bits so the epoch part overwrites nsec part. The second
change is only for coherency (2 -> EXT4_EPOCH_BITS)."
Thanks to Damien Guibouret for pointing out this problem.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The /proc/fs/ext4/<dev>/mb_history was maintained manually, and had a
number of problems: it required a largish amount of memory to be
allocated for each ext4 filesystem, and the s_mb_history_lock
introduced a CPU contention problem.
By ripping out the mb_history code and replacing it with ftrace
tracepoints, and we get more functionality: timestamps, event
filtering, the ability to correlate mballoc history with other ext4
tracepoints, etc.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
For async direct IO that covers holes or fallocate, the end_io
callback function now queued the convertion work on workqueue but
don't flush the work rightaway as it might take too long to afford.
But when fsync is called after all the data is completed, user expects
the metadata also being updated before fsync returns.
Thus we need to flush the conversion work when fsync() is called.
This patch keep track of a listed of completed async direct io that
has a work queued on workqueue. When fsync() is called, it will go
through the list and do the conversion.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Currently the DIO VFS code passes create = 0 when writing to the
middle of file. It does this to avoid block allocation for holes, so
as not to expose stale data out when there is a parallel buffered read
(which does not hold the i_mutex lock). Direct I/O writes into holes
falls back to buffered IO for this reason.
Since preallocated extents are treated as holes when doing a
get_block() look up (buffer is not mapped), direct IO over fallocate
also falls back to buffered IO. Thus ext4 actually silently falls
back to buffered IO in above two cases, which is undesirable.
To fix this, this patch creates unitialized extents when a direct I/O
write into holes in sparse files, and registering an end_io callback which
converts the uninitialized extent to an initialized extent after the
I/O is completed.
Singed-Off-By: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
When writing into an unitialized extent via direct I/O, and the direct
I/O doesn't exactly cover the unitialized extent, split the extent
into uninitialized and initialized extents before submitting the I/O.
This avoids needing to deal with an ENOSPC error in the end_io
callback that gets used for direct I/O.
When the IO is complete, the written extent will be marked as initialized.
Singed-Off-By: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Work around problems in the writeback code to force out writebacks in
larger chunks than just 4mb, which is just too small. This also works
around limitations in the ext4 block allocator, which can't allocate
more than 2048 blocks at a time. So we need to defeat the round-robin
characteristics of the writeback code and try to write out as many
blocks in one inode before allowing the writeback code to move on to
another inode. We add a a new per-filesystem tunable,
max_writeback_mb_bump, which caps this to a default of 128mb per
inode.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
There's no reason to redefine the maximum allowable offset
in an extent-based file just for defrag;
EXT_MAX_BLOCK already does this.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
EXT4_EXT_MIGRATE is only intended to be used for an in-memory flag,
and the hex value assigned to it collides with FS_DIRECTIO_FL (which
is also stored in i_flags). There's no reason for the
EXT4_EXT_MIGRATE bit to be stored in i_flags, so we switch it to use
i_state instead.
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Today, the ext4 allocator will happily allocate blocks past
2^32 for indirect-block files, which results in the block
numbers getting truncated, and corruption ensues.
This patch limits such allocations to < 2^32, and adds
BUG_ONs if we do get blocks larger than that.
This should address RH Bug 519471, ext4 bitmap allocator
must limit blocks to < 2^32
* ext4_find_goal() is modified to choose a goal < UINT_MAX,
so that our starting point is in an acceptable range.
* ext4_xattr_block_set() is modified such that the goal block
is < UINT_MAX, as above.
* ext4_mb_regular_allocator() is modified so that the group
search does not continue into groups which are too high
* ext4_mb_use_preallocated() has a check that we don't use
preallocated space which is too far out
* ext4_alloc_blocks() and ext4_xattr_block_set() add some BUG_ONs
No attempt has been made to limit inode locations to < 2^32,
so we may wind up with blocks far from their inodes. Doing
this much already will lead to some odd ENOSPC issues when the
"lower 32" gets full, and further restricting inodes could
make that even weirder.
For high inodes, choosing a goal of the original, % UINT_MAX,
may be a bit odd, but then we're in an odd situation anyway,
and I don't know of a better heuristic.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
There's no real cost for the journal checksum feature, and we should
make sure it is enabled all the time.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Add a new tracepoint which shows the pages that will be written using
write_cache_pages() by ext4_da_writepages().
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
unsigned short is potentially too small to track blocks within
a group; today it is safe due to restrictions in e2fsprogs but
we have _lo / _hi bits for group blocks with the intent to go
up to 32 bits, so clean this up now.
There are many more places where we use unsigned/int/unsigned int
to contain a group block but this should at least fix all the
short types.
I added a few comments to the struct ext4_group_info definition
as well.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
ext4_mb_update_group_info is only called in one place, and it's
extremely simple. There's no reason to have it in a separate function
in a separate file as far as I can tell, it just obfuscates what's
really going on.
Perhaps it was intended to keep the grp->bb_* manipulation local to
mballoc.c but we're already accessing other grp-> fields in balloc.c
directly so this seems ok.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
During truncate we are sometimes forced to start a new transaction as
the amount of blocks to be journaled is both quite large and hard to
predict. So far we restarted a transaction while holding i_data_sem
and that violates lock ordering because i_data_sem ranks below a
transaction start (and it can lead to a real deadlock with
ext4_get_blocks() mapping blocks in some page while having a
transaction open).
We fix the problem by dropping the i_data_sem before restarting the
transaction and acquire it afterwards. It's slightly subtle that this
works:
1) By the time ext4_truncate() is called, all the page cache for the
truncated part of the file is dropped so get_block() should not be
called on it (we only have to invalidate extent cache after we
reacquire i_data_sem because some extent from not-truncated part could
extend also into the part we are going to truncate).
2) Writes, migrate or defrag hold i_mutex so they are stopped for all
the time of the truncate.
This bug has been found and analyzed by Theodore Tso <tytso@mit.edu>.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Currently the group preallocation code tries to find a large (512)
free block from which to do per-cpu group allocation for small files.
The problem with this scheme is that it leaves the filesystem horribly
fragmented. In the worst case, if the filesystem is unmounted and
remounted (after a system shutdown, for example) we forget the fact
that wee were using a particular (now-partially filled) 512 block
extent. So the next time we try to allocate space for a small file,
we will find *another* completely free 512 block chunk to allocate
small files. Given that there are 32,768 blocks in a block group,
after 64 iterations of "mount, write one 4k file in a directory,
unmount", the block group will have 64 files, each separated by 511
blocks, and the block group will no longer have any free 512
completely free chunks of blocks for group preallocation space.
So if we try to allocate blocks for a file that has been closed, such
that we know the final size of the file, and the filesystem is not
busy, avoid using group preallocation.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The logic around sbi->s_mb_last_group and sbi->s_mb_last_start was all
screwed up. These fields were getting unconditionally all the time,
set even when stream allocation had not taken place, and if they were
being used when the file was smaller than s_mb_stream_request, which
is when the allocation should _not_ be doing stream allocation.
Fix this by determining whether or not we stream allocation should
take place once, in ext4_mb_group_or_file(), and setting a flag which
gets used in ext4_mb_regular_allocator() and ext4_mb_use_best_found().
This simplifies the code and assures that we are consistently using
(or not using) the stream allocation logic.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The function ext4_mb_free_blocks() was using an "unsigned long" to
pass a block number; this will cause 64-bit block numbers to get
truncated on x86 and other 32-bit platforms.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Enhance the inode allocator to take a goal inode number as a
paremeter; if it is specified, it takes precedence over Orlov or
parent directory inode allocation algorithms.
The extents migration function uses the goal inode number so that the
extent trees allocated the migration function use the correct flex_bg.
In the future, the goal inode functionality will also be used to
allocate an adjacent inode for the extended attributes.
Also, for testing purposes the goal inode number can be specified via
/sys/fs/{dev}/inode_goal. This can be useful for testing inode
allocation beyond 2^32 blocks on very large filesystems.
Signed-off-by: Andreas Dilger <adilger@sun.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Instead of using a random number to determine the goal parent grop for
the Orlov top directories, use a hash of the directory name. This
allows for repeatable results when trying to benchmark filesystem
layout algorithms.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
We're running out of space in the mount options word, and
EXT4_MOUNT_ABORT isn't really a mount option, but a run-time flag. So
move it to become EXT4_MF_FS_ABORTED in s_mount_flags.
Also remove bogus ext2_fs.h / ext4.h simultaneous #include protection,
which can never happen.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This field can be very helpful when a system administrator is trying
to sort through large numbers of block devices or filesystem images.
What is stored in this field can be ambiguous if multiple filesystem
namespaces are in play; what we store in practice is the mountpoint
interpreted by the process's namespace which first opens a file in the
filesystem.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
We can only fit 32 options in s_mount_opt because an unsigned long is
32-bits on a x86 machine. So use an unsigned int to save space on
64-bit platforms.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The EXT4_IOC_MOVE_EXT exchanges the blocks between orig_fd and donor_fd,
and then write the file data of orig_fd to donor_fd.
ext4_mext_move_extent() is the main fucntion of ext4 online defrag,
and this patch includes all functions related to ext4 online defrag.
Signed-off-by: Akira Fujita <a-fujita@rs.jp.nec.com>
Signed-off-by: Takashi Sato <t-sato@yk.jp.nec.com>
Signed-off-by: Kazuya Mio <k-mio@sx.jp.nec.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This patch changes ext4 super.c to include the device name with all
warning/error messages, by using a new utility function ext4_msg.
It's a rather large patch, but very mechanic. I left debug printks
alone.
This is a straightforward port of a patch which Andi Kleen did for
ext3.
Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Get rid of EXTEND_DISKSIZE flag of ext4_get_blocks_handle(). This
seems to be a relict from some old days and setting disksize in this
function does not make much sense. Currently it was set only by
ext4_getblk(). Since the parameter has some effect only if create ==
1, it is easy to check by grepping through the sources that the three
callers which end up calling ext4_getblk() with create == 1
(ext4_append, ext4_quota_write, ext4_mkdir) do the right thing and set
disksize themselves.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
To catch filesystem bugs or corruption which could lead to the
filesystem getting severly damaged, this patch adds a facility for
tracking all of the filesystem metadata blocks by contiguous regions
in a red-black tree. This allows quick searching of the tree to
locate extents which might overlap with filesystem metadata blocks.
This facility is also used by the multi-block allocator to assure that
it is not allocating blocks out of the system zone, as well as by the
routines used when reading indirect blocks and extents information
from disk to make sure their contents are valid.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The ext4_get_blocks() function was depending on the value of
bh_result->b_state as an input parameter to decide whether or not
update the delalloc accounting statistics by calling
ext4_da_update_reserve_space(). We now use a separate flag,
EXT4_GET_BLOCKS_UPDATE_RESERVE_SPACE, to requests this update, so that
all callers of ext4_get_blocks() can clear map_bh.b_state before
calling ext4_get_blocks() without worrying about any consistency
issues.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The functions ext4_get_blocks(), ext4_ext_get_blocks(), and
ext4_ind_get_blocks() used an ad-hoc set of integer variables used as
boolean flags passed in as arguments. Use a single flags parameter
and a setandard set of bitfield flags instead. This saves space on
the call stack, and it also makes the code a bit more understandable.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Another function rename for clarity's sake. The _wrap prefix simply
confuses people, and didn't add much people trying to follow the code
paths.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
On UP systems without DEBUG_SPINLOCK, ext4_is_group_locked always fails
which triggers a BUG_ON() call.
This patch fixes it by using assert_spin_locked instead.
Signed-off-by: Vincent Minet <vincent@vincent-minet.net>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
We have sb_bgl_lock() and ext4_group_info.bb_state
bit spinlock to protech group information. The later is only
used within mballoc code. Consolidate them to use sb_bgl_lock().
This makes the mballoc.c code much simpler and also avoid
confusion with two locks protecting same info.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The fs/ext4/namei.h header file had only a single function
declaration, and should have never been a standalone file. Move it
into ext4.h, where should have been from the beginning.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
There is no longer a reason for a separate ext4_sb.h header file, so
move it into ext4.h just to make life easier for developers to find
the relevant data structures and typedefs. Should also speed up
compiles slightly, too.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
There is no longer a reason for a separate ext4_i.h header file, so
move it into ext4.h just to make life easier for developers to find
the relevant data structures and typedefs. Should also speed up
compiles slightly, too.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Ext4's on-line resizing adds a new block group and then, only at the
last step adjusts s_groups_count. However, it's possible on SMP
systems that another CPU could see the updated the s_group_count and
not see the newly initialized data structures for the just-added block
group. For this reason, it's important to insert a SMP read barrier
after reading s_groups_count and before reading any (for example) the
new block group descriptors allowed by the increased value of
s_groups_count.
Unfortunately, we rather blatently violate this locking protocol
documented in fs/ext4/resize.c. Fortunately, (1) on-line resizes
happen relatively rarely, and (2) it seems rare that the filesystem
code will immediately try to use just-added block group before any
memory ordering issues resolve themselves. So apparently problems
here are relatively hard to hit, since ext3 has been vulnerable to the
same issue for years with no one apparently complaining.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (33 commits)
ext4: Regularize mount options
ext4: fix locking typo in mballoc which could cause soft lockup hangs
ext4: fix typo which causes a memory leak on error path
jbd2: Update locking coments
ext4: Rename pa_linear to pa_type
ext4: add checks of block references for non-extent inodes
ext4: Check for an valid i_mode when reading the inode from disk
ext4: Use WRITE_SYNC for commits which are caused by fsync()
ext4: Add auto_da_alloc mount option
ext4: Use struct flex_groups to calculate get_orlov_stats()
ext4: Use atomic_t's in struct flex_groups
ext4: remove /proc tuning knobs
ext4: Add sysfs support
ext4: Track lifetime disk writes
ext4: Fix discard of inode prealloc space with delayed allocation.
ext4: Automatically allocate delay allocated blocks on rename
ext4: Automatically allocate delay allocated blocks on close
ext4: add EXT4_IOC_ALLOC_DA_BLKS ioctl
ext4: Simplify delalloc code by removing mpage_da_writepages()
ext4: Save stack space by removing fake buffer heads
...
Change the page_mkwrite prototype to take a struct vm_fault, and return
VM_FAULT_xxx flags. There should be no functional change.
This makes it possible to return much more detailed error information to
the VM (and also can provide more information eg. virtual_address to the
driver, which might be important in some special cases).
This is required for a subsequent fix. And will also make it easier to
merge page_mkwrite() with fault() in future.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <joel.becker@oracle.com>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Cc: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Uses quota reservation/claim/release to handle quota properly for delayed
allocation in the three steps: 1) quotas are reserved when data being copied
to cache when block allocation is defered 2) when new blocks are allocated.
reserved quotas are converted to the real allocated quota, 2) over-booked
quotas for metadata blocks are released back.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Acked-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Jan Kara <jack@suse.cz>
Add a mount option which allows the user to disable automatic
allocation of blocks whose allocation by delayed allocation when the
file was originally truncated or when the file is renamed over an
existing file. This feature is intended to save users from the
effects of naive application writers, but it reduces the effectiveness
of the delayed allocation code. This mount option disables this
safety feature, which may be desirable for prodcutions systems where
the risk of unclean shutdowns or unexpected system crashes is low.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Instead of looping over all of the block groups in a flex group
summing their summary statistics, start tracking used_dirs in struct
flex_groups, and use struct flex_groups instead. This should save a
bit of CPU for mkdir-heavy workloads.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reduce pressure on the sb_bgl_lock family of locks by using atomic_t's
to track the number of free blocks and inodes in each flex_group.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Remove tuning knobs in /proc/fs/ext4/<dev/* since they have been
replaced by knobs in sysfs at /sys/fs/ext4/<dev>/*.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Add a new superblock value which tracks the lifetime amount of writes
to the filesystem. This is useful in estimating the amount of wear on
solid state drives (SSD's) caused by writes to the filesystem.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
When closing a file that had been previously truncated, force any
delay allocated blocks that to be allocated so that if the filesystem
is mounted with data=ordered, the data blocks will be pushed out to
disk along with the journal commit. Many application programs expect
this, so we do this to avoid zero length files if the system crashes
unexpectedly.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Add an ioctl which forces all of the delay allocated blocks to be
allocated. This also provides a function ext4_alloc_da_blocks() which
will be used by the following commits to force files to be fully
allocated to preserve application-expected ext3 behaviour.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The find_group_flex() inode allocator is now only used if the
filesystem is mounted using the "oldalloc" mount option. It is
replaced with the original Orlov allocator that has been updated for
flex_bg filesystems (it should behave the same way if flex_bg is
disabled). The inode allocator now functions by taking into account
each flex_bg group, instead of each block group, when deciding whether
or not it's time to allocate a new directory into a fresh flex_bg.
The block allocator has also been changed so that the first block
group in each flex_bg is preferred for use for storing directory
blocks. This keeps directory blocks close together, which is good for
speeding up e2fsck since large directories are more likely to look
like this:
debugfs: stat /home/tytso/Maildir/cur
Inode: 1844562 Type: directory Mode: 0700 Flags: 0x81000
Generation: 1132745781 Version: 0x00000000:0000ad71
User: 15806 Group: 15806 Size: 1060864
File ACL: 0 Directory ACL: 0
Links: 2 Blockcount: 2072
Fragment: Address: 0 Number: 0 Size: 0
ctime: 0x499c0ff4:164961f4 -- Wed Feb 18 08:41:08 2009
atime: 0x499c0ff4:00000000 -- Wed Feb 18 08:41:08 2009
mtime: 0x49957f51:00000000 -- Fri Feb 13 09:10:25 2009
crtime: 0x499c0f57:00d51440 -- Wed Feb 18 08:38:31 2009
Size of extra inode fields: 28
BLOCKS:
(0):7348651, (1-258):7348654-7348911
TOTAL: 259
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
At the moment there are few restrictions on which flags may be set on
which inodes. Specifically DIRSYNC may only be set on directories and
IMMUTABLE and APPEND may not be set on links. Tighten that to disallow
TOPDIR being set on non-directories and only NODUMP and NOATIME to be set
on non-regular file, non-directories.
Introduces a flags masking function which masks flags based on mode and
use it during inode creation and when flags are set via the ioctl to
facilitate future consistency.
Signed-off-by: Duane Griffin <duaneg@dghda.com>
Acked-by: Andreas Dilger <adilger@sun.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
At present INDEX and EXTENTS are the only flags that new ext4 inodes do
NOT inherit from their parent. In addition prevent the flags DIRTY,
ECOMPR, IMAGIC, TOPDIR, HUGE_FILE and EXT_MIGRATE from being inherited.
List inheritable flags explicitly to prevent future flags from
accidentally being inherited.
This fixes the TOPDIR flag inheritance bug reported at
http://bugzilla.kernel.org/show_bug.cgi?id=9866.
Signed-off-by: Duane Griffin <duaneg@dghda.com>
Acked-by: Andreas Dilger <adilger@sun.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The rec_len field in the directory entry is 16 bits, so to encode
blocksizes larger than 64k becomes problematic. This patch allows us
to supprot block sizes up to 256k, by using the low 2 bits to extend
the range of rec_len to 2**18-1 (since valid rec_len sizes must be a
multiple of 4). We use the convention that a rec_len of 0 or 65535
means the filesystem block size, for compatibility with older kernels.
It's unlikely we'll see VM pages of up to 256k, but at some point we
might find that the Linux VM has been enhanced to support filesystem
block sizes > than the VM page size, at which point it might be useful
for some applications to allow very large filesystem block sizes.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The rec_len field in the directory entry is 16 bits, so there was a
problem representing rec_len for filesystems with a 64k block size in
the case where the directory entry takes the entire 64k block.
Unfortunately, there were two schemes that were proposed; one where
all zeros meant 65536 and one where all ones (65535) meant 65536.
E2fsprogs used 0, whereas the kernel used 65535. Oops. Fortunately
this case happens extremely rarely, with the most common case being
the lost+found directory, created by mke2fs.
So we will be liberal in what we accept, and accept both encodings,
but we will continue to encode 65536 as 65535. This will require a
change in e2fsprogs, but with fortunately ext4 filesystems normally
have the dir_index feature enabled, which precludes having a
completely empty directory block.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Remove some leftovers from when the old block allocator was removed
(c2ea3fde). ext4_sb_info is now a bit lighter. Also remove a dangling
read_block_bitmap() prototype.
Signed-off-by: Mike Snitzer <snitzer@gmail.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Directories are not allowed to be bigger than 2GB, so don't use
i_size_high for anything other than regular files. E2fsck should
complain about these inodes, but the simplest thing to do for the
kernel is to only use i_size_high for regular files.
This prevents an intentially corrupted filesystem from causing the
kernel to burn a huge amount of CPU and issuing error messages such
as:
EXT4-fs warning (device loop0): ext4_block_to_path: block 135090028 > max
Thanks to David Maciejak from Fortinet's FortiGuard Global Security
Research Team for reporting this issue.
http://bugzilla.kernel.org/show_bug.cgi?id=12375
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (57 commits)
jbd2: Fix oops in jbd2_journal_init_inode() on corrupted fs
ext4: Remove "extents" mount option
block: Add Kconfig help which notes that ext4 needs CONFIG_LBD
ext4: Make printk's consistently prefixed with "EXT4-fs: "
ext4: Add sanity checks for the superblock before mounting the filesystem
ext4: Add mount option to set kjournald's I/O priority
jbd2: Submit writes to the journal using WRITE_SYNC
jbd2: Add pid and journal device name to the "kjournald2 starting" message
ext4: Add markers for better debuggability
ext4: Remove code to create the journal inode
ext4: provide function to release metadata pages under memory pressure
ext3: provide function to release metadata pages under memory pressure
add releasepage hooks to block devices which can be used by file systems
ext4: Fix s_dirty_blocks_counter if block allocation failed with nodelalloc
ext4: Init the complete page while building buddy cache
ext4: Don't allow new groups to be added during block allocation
ext4: mark the blocks/inode bitmap beyond end of group as used
ext4: Use new buffer_head flag to check uninit group bitmaps initialization
ext4: Fix the race between read_inode_bitmap() and ext4_new_inode()
ext4: code cleanup
...
For NR_CPUS >= 16 values, FBC_BATCH is 2*NR_CPUS
Considering more and more distros are using high NR_CPUS values, it makes
sense to use a more sensible value for FBC_BATCH, and get rid of NR_CPUS.
A sensible value is 2*num_online_cpus(), with a minimum value of 32 (This
minimum value helps branch prediction in __percpu_counter_add())
We already have a hotcpu notifier, so we can adjust FBC_BATCH dynamically.
We rename FBC_BATCH to percpu_counter_batch since its not a constant
anymore.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This mount option is largely superfluous, and in fact the way it was
implemented was buggy; if a filesystem which did not have the extents
feature flag was mounted -o extents, the filesystem would attempt to
create and use extents-based file even though the extents feature flag
was not eabled. The simplest thing to do is to nuke the mount option
entirely. It's not all that useful to force the non-creation of new
extent-based files if the filesystem can support it.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
For uninit block group, the on-disk bitmap is not initialized. That
implies we cannot depend on the uptodate flag on the bitmap
buffer_head to find bitmap validity. Use a new buffer_head flag which
would be set after we properly initialize the bitmap. This also
prevents (re-)initializing the uninit group bitmap every time we call
ext4_read_block_bitmap().
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
Rename the lower bits with suffix _lo and add helper
to access the values. Also rename bg_itable_unused_hi
to bg_pad as in e2fsprogs.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The mballoc code likes to call ext4_error while it is holding locked
block groups. This can causes a scheduling in atomic context BUG. We
can't just unlock the block group and relock it after/if ext4_error
returns since that might result in race conditions in the case where
the filesystem is set to continue after finding errors.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The new groups added during resize are flagged as
need_init group. Make sure we properly initialize these
groups. When we have block size < page size and we are adding
new groups the page may still be marked uptodate even though
we haven't initialized the group. While forcing the init
of buddy cache we need to make sure other groups part of the
same page of buddy cache is not using the cache.
group_info->alloc_sem is added to ensure the same.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
cc: stable@kernel.org
With this change new blocks added during resize
are marked as free in the block bitmap and the
group is flagged with EXT4_GROUP_INFO_NEED_INIT_BIT
flag. This makes sure when mballoc tries to allocate
blocks from the new group we would reload the
buddy information using the bitmap present in the disk.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
* Change EXT4_HAS_*_FEATURE to return a boolean
* Add a function prototype for ext4_fiemap() in ext4.h
* Make ext4_ext_fiemap_cb() and ext4_xattr_fiemap() be static functions
* Add lock annotations to mb_free_blocks()
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Convert the unsigned longs that are most responsible for bloating the
stack usage on 64-bit systems.
Nearly all places in the ext3/4 code which uses "unsigned long" is
probably a bug, since on 32-bit systems a ulong a 32-bits, which means
we are wasting stack space on 64-bit systems.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Nearly all places in the ext3/4 code which uses "unsigned long" is
probably a bug, since on 32-bit systems a ulong a 32-bits, which means
we are wasting stack space on 64-bit systems.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Add new mount options, min_batch_time and max_batch_time, which
controls how long the jbd2 layer should wait for additional filesystem
operations to get batched with a synchronous write transaction.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
There were only two one callers of the function ext4_new_meta_block(),
which just a very simpler wrapper function around
ext4_new_meta_blocks(). Change those two functions to call
ext4_new_meta_blocks() directly, to save code and stack space usage.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
There was only one caller of the compatibility function
ext4_new_blocks(), in balloc.c's ext4_alloc_blocks(). Change it to
call ext4_mb_new_blocks() directly, and remove ext4_new_blocks()
altogether. This cleans up the code, by removing two extra functions
from the call chain, and hopefully saving some stack usage.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The original ext3 hash algorithms assumed that variables of type char
were signed, as God and K&R intended. Unfortunately, this assumption
is not true on some architectures. Userspace support for marking
filesystems with non-native signed/unsigned chars was added two years
ago, but the kernel-side support was never added (until now).
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Mingming pointed out that ext4_claim_free_blocks & ext4_has_free_blocks
are largely cut & pasted; they can be collapsed/merged as follows.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
If the journal doesn't abort when it gets an IO error in file data
blocks, the file data corruption will spread silently. Because
most of applications and commands do buffered writes without fsync(),
they don't notice the IO error. It's scary for mission critical
systems. On the other hand, if the journal aborts whenever it gets
an IO error in file data blocks, the system will easily become
inoperable. So this patch introduces a filesystem option to
determine whether it aborts the journal or just call printk() when
it gets an IO error in file data.
If you mount an ext4 fs with data_err=abort option, it aborts on file
data write error. If you mount it with data_err=ignore, it doesn't
abort, just call printk(). data_err=ignore is the default.
Here is the corresponding patch of the ext3 version:
http://kerneltrap.org/mailarchive/linux-kernel/2008/9/9/3239374
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
ext4_ext_walk_space() was reinstated to be used for iterating over file
extents with a callback; it is used by the ext4 fiemap implementation.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: linux-ext4@vger.kernel.org
Cc: linux-fsdevel@vger.kernel.org
With modern hard drives, reading 64k takes roughly the same time as
reading a 4k block. So request readahead for adjacent inode table
blocks to reduce the time it takes when iterating over directories
(especially when doing this in htree sort order) in a cold cache case.
With this patch, the time it takes to run "git status" on a kernel
tree after flushing the caches via "echo 3 > /proc/sys/vm/drop_caches"
is reduced by 21%.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Previously mballoc created a separate set of functions for each proc
file. This combines the tunables into a single set of functions which
gets used for all of the per-superblock proc files, saving
approximately 2k of compiled object code.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
...and into the core setup/teardown code in fs/ext4/super.c so that
other parts of ext4 can define tuning parameters.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Pick an ioctl number for EXT4_IOC_MIGRATE that won't conflict with
other ext4 ioctl's. Since there haven't been any major userspace
users of this ioctl, we can afford to change this now, to avoid
potential problems later.
Also, reorder the ioctl numbers in ext4.h to avoid this sort of
mistake in the future.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This patch hooks the ext3 to ext4 migrate interface to
EXT4_IOC_SETFLAGS ioctl. The userspace interface is via chattr +e. We
only allow setting extent flags. Clearing extent flag (migrating from
ext4 to ext3) is not supported.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The migrate ioctl writes to the filsystem, so we need to elevate the
write count.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
With delayed allocation we use i_data_sem to update i_disksize. We need
to update i_disksize only if the new size specified is greater than the
current value and we need to make sure we don't race with other
i_disksize update. With delayed allocation we will switch to the
write_begin function for non-delayed allocation if we are low on free
blocks. This means the write_begin function for non-delayed allocation
also needs to use the same locking.
We also need to check and update i_disksize even if the new size is less
that inode.i_size because of delayed allocation.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This patch converts some usage of ext4_fsblk_t to s64. This is needed
so that some of the sign conversion works as expected in if loops.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
With delayed allocation we need to make sure block are reserved before
we attempt to allocate them. Otherwise we get block allocation failure
(ENOSPC) during writepages which cannot be handled. This would mean
silent data loss (We do a printk stating data will be lost). This patch
updates the DIO and fallocate code path to do block reservation before
block allocation. This is needed to make sure parallel DIO and fallocate
request doesn't take block out of delayed reserve space.
When free blocks count go below a threshold we switch to a slow patch
which looks at other CPU's accumulated percpu counter values.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
DIO and fallocate credit calculation is different than writepage, as
they do start a new journal right for each call to ext4_get_blocks_wrap().
This patch uses the helper function in DIO and fallocate case, passing
a flag indicating that the modified data are contigous thus could account
less indirect/index blocks.
This patch also fixed the journal credit reservation for direct I/O
(DIO). Previously the estimated credits for DIO only was calculated for
non-extent files, which was not enough if the file is extent-based.
Also fixed was fallocate double-counting credits for modifying the the
superblock.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
When considering how many journal credits are needed for modifying a
chunk of data, we need to account for the super block, inode block,
quota blocks and xattr block, indirect/index blocks, also, group bitmap
and group descriptor blocks for new allocation (including data and
indirect/index blocks). There are many places in ext4 do the calculation
on their own and often missed one or two meta blocks, and often they
assume single block allocation, and did not considering the multile
chunk of allocation case.
This patch is trying to cleanup current journal credit code, provides
some common helper funtion to calculate the journal credits, to be used
for writepage, writepages, DIO, fallocate, migration, defrag, and for
both nonextent and extent files.
This patch modified the writepage/write_begin credit caculation for
nonextent files, to use the new helper function. It also fixed the
problem that writepage on nonextent files did not consider the case
blocksize <pagesize, thus could possibelly need multiple block
allocation in a single transaction.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The truncate patch should not use the i_allocated_meta_blocks
value. So add seperate functions to be used in the truncate
and alloc path. We also need to release the meta-data block
that we reserved for the blocks that we are truncating.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Right now i_blocks is not getting updated until the blocks are actually
allocaed on disk. This means with delayed allocation, right after files
are copied, "ls -sF" shoes the file as taking 0 blocks on disk. "du"
also shows the files taking zero space, which is highly confusing to the
user.
Since delayed allocation already keeps track of per-inode total
number of blocks that are subject to delayed allocation, this patch fix
this by using that to adjust the value returned by stat(2). When real
block allocation is done, the i_blocks will get updated. Since the
reserved blocks for delayed allocation will be decreased, this will be
keep value returned by stat(2) consistent.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This patch does block reservation for delayed
allocation, to avoid ENOSPC later at page flush time.
Blocks(data and metadata) are reserved at da_write_begin()
time, the freeblocks counter is updated by then, and the number of
reserved blocks is store in per inode counter.
At the writepage time, the unused reserved meta blocks are returned
back. At unlink/truncate time, reserved blocks are properly released.
Updated fix from Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
to fix the oldallocator block reservation accounting with delalloc, added
lock to guard the counters and also fix the reservation for meta blocks.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Updated with fixes from Mingming Cao <cmm@us.ibm.com> to unlock and
release the page from page cache if the delalloc write_begin failed, and
properly handle preallocated blocks. Also added a fix to clear
buffer_delay in block_write_full_page() after allocating a delayed
buffer.
Updated with fixes from Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
to update i_disksize properly and to add bmap support for delayed
allocation.
Updated with a fix from Valerie Clement <valerie.clement@bull.net> to
avoid filesystem corruption when the filesystem is mounted with the
delalloc option and blocksize < pagesize.
Signed-off-by: Alex Tomas <alex@clusterfs.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
This changes are needed to support data=ordered mode handling via
inodes. This enables us to get rid of the journal heads and buffer
heads for data buffers in the ordered mode. With the changes, during
tranasaction commit we writeout the inode pages using the
writepages()/writepage(). That implies we take page lock during
transaction commit. This can cause a deadlock with the locking order
page_lock -> jbd2_journal_start, since the jbd2_journal_start can wait
for the journal_commit to happen and the journal_commit now needs to
take the page lock. To avoid this dead lock reverse the locking order.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
We would like to get notified when we are doing a write on mmap section.
This is needed with respect to preallocated area. We split the preallocated
area into initialzed extent and uninitialzed extent in the call back. This
let us handle ENOSPC better. Otherwise we get ENOSPC in the writepage and
that would result in data loss. The changes are also needed to handle ENOSPC
when writing to an mmap section of files with holes.
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Update group infos when updating a group's descriptor.
Add group infos when adding a group's descriptor.
Refresh cache pages used by mb_alloc when changes occur.
This will probably need modifications when META_BG resizing will be allowed.
Signed-off-by: Frederic Bohe <frederic.bohe@bull.net>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
mballoc allocation missed check for blocks reserved for root users. Add
ext4_has_free_blocks() check before allocation. Also modified
ext4_has_free_blocks() to support multiple block allocation request.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Move the code related to block allocation to a single function and add helper
funtions to differient allocation for data and meta data blocks
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
When mballoc is enabled, block allocation for old block-based
files are allocated using mballoc allocator instead of old
block-based allocator. The old ext3 block reservation is turned
off when mballoc is turned on.
However, the in-core preallocation is not enabled for block-based/
non-extent based file block allocation. This result in performance
regression, as now we don't have "reservation" ore in-core preallocation
to prevent interleaved fragmentation in multiple writes workload.
This patch fix this by enable per inode in-core preallocation
for non extent files when mballoc is used.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This patch mostly controls the way inode are allocated in order to
make ialloc aware of flex_bg block group grouping. It achieves this
by bypassing the Orlov allocator when block group meta-data are packed
toghether through mke2fs. Since the impact on the block allocator is
minimal, this patch should have little or no effect on other block
allocation algorithms. By controlling the inode allocation, it can
basically control where the initial search for new block begins and
thus indirectly manipulate the block allocator.
This allocator favors data and meta-data locality so the disk will
gradually be filled from block group zero upward. This helps improve
performance by reducing seek time. Since the group of inode tables
within one flex_bg are treated as one giant inode table, uninitialized
block groups would not need to partially initialize as many inode
table as with Orlov which would help fsck time as the filesystem usage
goes up.
Signed-off-by: Jose R. Santos <jrs@us.ibm.com>
Signed-off-by: Valerie Clement <valerie.clement@bull.net>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
If the orphan node list includes valid, untruncatable nodes with nlink > 0
the ext4_orphan_cleanup loop which attempts to delete them will not do so,
causing it to loop forever. Fix by checking for such nodes in the
ext4_orphan_get function.
This patch fixes the second case (image hdb.20000009.softlockup.gz)
reported in http://bugzilla.kernel.org/show_bug.cgi?id=10882.
Signed-off-by: Duane Griffin <duaneg@dghda.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Move ext4 headers out of include/linux. This is just the trivial move,
there's some more thing that could be done later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
