In ETSI region DFS slave device can operate in two modes on DFS channels:
- do on-channel radar detection and use higher Tx power
- don't do radar detection and use lower Tx power as a consequence
Allow user to control that behavior through qtnfmac module parameter.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use control path to send EAPOL frames to make sure they are
sent with higher priority with aggregation disabled.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wireless core calls regulatory notifier for each wiphy and it only
guarantees that bands info is updated for this particular wiphy prior
to calling a notifier. Hence updating all wiphy which belong to driver
in a single notifier callback is redundant and incorrect.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the case of SAE AP, drivers offload authentication to user-space
software, e.g. hostapd. For FullMAC drivers the procedure is as follows.
If auth_type is SAE and user space indicates external authentication
capability, then driver requests authentication offload to user-space
software using cfg80211_external_auth_request call. From that point,
auth frame exchange is performed transparently for driver: user-space
software sends/receives mgmt frames using mgmt_tx/mgmt_frame_register
cfg80211 callbacks. As soon as authenitcation is completed, user-space
software notifies driver about its status using external_auth cfg80211
callback.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace textual license with SPDX-License-Identifier.
Add an SPDX-License-Identifier for the Makefile.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Advertise WIPHY_FLAG_4ADDR_STATION capability to wireless core. Send
use4addr interface change flag to firmware in change_virtual_intf
cfg80211 callback.
In order to enable adding wireless station interface to bridge
one should turn on 4addr mode using the following command:
$ iw dev wlan0 set 4addr on
$ brctl addif br0 wlan0
If this commands succeeds, then interface can be added to bridge.
Note that when wireless interface is added to bridge, wpa_supplicant
should be started with appropriate -b <brname> parameter, e.g:
$ wpa_supplicant -Dnl80211 -iwlan0 -c/path/to/wpa.conf -b br0
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch implements basic WoWLAN support in qtnfmac driver, including
processing of WoWLAN features reported by firmware and implementation
of cfg80211 suspend/resume/wakeup callbacks. Currently the following
WoWLAN triggers are supported: disconnect, magic packet,
custom pattern packet.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement set_power_mgmt() callback that forwards power saving
settings to the device firmware.
Signed-off-by: Sergei Maksimenko <smaksimenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Functions qtnf_cmd_resp_parse and qtnf_cmd_resp_check have
been removed. Remove their declarations as well.
Signed-off-by: Andrey Shevchenko <ashevchenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This allows a running AP to blacklist STAs by their MAC addresses
respecting the configured policy (either accept or deny unless listed).
It can be setup on .start_ap or with .set_mac_acl commands.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement two parts of radar handling logic:
- cfg80211 .start_radar_detect callback to allow nl80211 to initiate CAC
- radar event to allow wlan device to advertize CAC and radar events
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current logic artificially divides "start AP" procedure into three
stages:
- generic interface configuration (security, channel etc)
- IE's processing
- enable AP mode on interface
This separation would not allow to do a proper device configuration as
first stage needs to use information from IEs that are processed on
a second stage. Which means first and second stages have to be meged.
In that case there is no point anymore to keep third stage either, so
merge all three into a single command.
This new command carries all the same info as contained in
"struct cfg80211_ap_settings".
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HT/VHT capabilities must be reported per each band supported by a radio,
not for all bands on a radio. Furthermore, driver better not assume
any capabilities and just use whetever is reported by device itself.
To support this, convert "get channels" command into "get band info"
command. Difference is that it may also carry HT/VHT capabilities along
with channels information.
While at it, also add "num_bitrates" field to "get band info" command,
for future use.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cached AP setings are passed to WiFi card right after they are
initialized and are never used for anything else. There is no
point in keeping them in driver state.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not assume whether wireless device can or can not handle switching
several interfaces on a single radio to different channels. Device will
handle it itself and will return appropriate error code.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not try to cache current operational channel info in driver, this
is a potential source of synchronization issues + driver does not
really need that info.
Introduce GET_CHANNEL command and process it appropriately.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch implements cfg80211 channel_switch handler enabling CSA
channel-switch procedure.
Driver performs only basic validation of the requested new channel
and then sends command to firmware. Beacon IEs are not sent since
beacon update is handled by firmware.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On startup driver obtains regulatory rules from firmware and
enables them during wiphy registration. Later on regulatory
domain change can be requested by host. In this case firmware
is notified about the upcoming changes. If the change is valid,
then firmware updates hardware channel configuration and host
driver receives updated channel info for each band.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for new FullMAC WiFi driver for Quantenna
QSR10G chipsets.
QSR10G (aka Pearl) is Quantenna's 8x8, 160M, 11ac offering.
QSR10G supports 2 simultaneous WMACs - one 5G and one 2G.
5G WMAC supports 160M, 8x8 configuration. FW supports
up to 8 concurrent virtual interfaces on each WMAC.
Patch introduces 2 new drivers:
- qtnfmac.ko for interfacing with kernel wireless core
- qtnfmac_pearl_pcie.ko for interfacing with hardware over PCIe interface
Signed-off-by: Dmitrii Lebed <dlebed@quantenna.com>
Signed-off-by: Sergei Maksimenko <smaksimenko@quantenna.com>
Signed-off-by: Sergey Matyukevich <smatyukevich@quantenna.com>
Signed-off-by: Bindu Therthala <btherthala@quantenna.com>
Signed-off-by: Huizhao Wang <hwang@quantenna.com>
Signed-off-by: Kamlesh Rath <krath@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
