If we fail to to grab NIC access because the device is not responding
(i.e. CSR_GP_CNTRL returns 0xFFFFFFFF), remove the device from the PCI
bus, to avoid any further damage, and to let the user space rescan.
In order to inform the userspace that a rescan is needed, we send a
kobject uevent with "INACCESSIBLE".
This functionality is disabled by default, but can be enabled via a
new module parameter called "remove_when_gone". In the future we may
change this module parameter to include 3 modes instead: do nothing;
auto-rescan or; send uevent.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Rajat Jain <rajatja@google.com>
Different device families may have different flag values
for passing a message to the fw (i.e. SW_RESET).
In order to keep the code readable, and avoid conditioning
upon the family, store a value for each flag, which indicates
the bit that needs to be enabled.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Most of the sw resets in the code are done by one function,
which writes to the relevant CSR.
Use the common function to perform the only reset which was
done separately, redundant to the common code.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support internal debug data collection on 9000 and newer
devices.
The method for finding the base and end address has changed
on new HW's, so introduce a new version of debug destination
tlv.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A bigger pull request this time, the most visible change being the new
driver mt76. But there's also Kconfig refactoring in ath9k and ath10k,
work beginning in iwlwifi to have rate scaling in firmware/hardware,
wcn3990 support getting closer in ath10k and lots of smaller changes.
mt76
* a new driver for MT76x2e, a 2x2 PCIe 802.11ac chipset by MediaTek
ath10k
* enable multiqueue support for all hw using mac80211 wake_tx_queue op
* new Kconfig option ATH10K_SPECTRAL to save RAM
* show tx stats on QCA9880
* new qcom,ath10k-calibration-variant DT entry
* WMI layer support for wcn3990
ath9k
* new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM
wcn36xx
* hardware scan offload support
wil6210
* run-time PM support when interface is down
iwlwifi
* initial work for rate-scaling offload
* Support for new FW API version 36
* Rename the temporary hw name A000 to 22000
ssb
* make SSB a menuconfig to ease disabling it all
mwl8k
* enable non-DFS 5G channels 149-165
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaN8MiAAoJEG4XJFUm622bGN4H/jc7+JqGUMozK8CKe5UGFnu7
HlwP3Vpz7SR655CgoMzvNzJ6lvBxaPA77epPFkALuwua3J22feakv5UGipT7RPI/
EtFCtq6+dIB+qooJ/8hUQVfAV8o13+dQzBQqtp7Wg37ok0qhcGpTLsvf2rI0ZG1R
+lcC2Jyk0lYjAPuPri3+KjxPLkZhGbx/hCdKwxQfCoubEVoqimMcQ68+RqU3rxNB
Of2Sk8IsaIevantLPnmO0+9OhZiMyoy4QGSnnuHntdpgZqEl0NbmVshQONCU9oTu
3RPKvbbYe57gRfgLKEvqTvij5R8ZxxwF+BFacaXch7Q9k6pMoJuyD6gJ8/S8AW8=
=FTCb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-12-18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
The drivers/net/wireless/intel/iwlwifi/pcie/drv.c conflict was
resolved using a diff provided by Kalle in his pull request.
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
A bigger pull request this time, the most visible change being the new
driver mt76. But there's also Kconfig refactoring in ath9k and ath10k,
work beginning in iwlwifi to have rate scaling in firmware/hardware,
wcn3990 support getting closer in ath10k and lots of smaller changes.
mt76
* a new driver for MT76x2e, a 2x2 PCIe 802.11ac chipset by MediaTek
ath10k
* enable multiqueue support for all hw using mac80211 wake_tx_queue op
* new Kconfig option ATH10K_SPECTRAL to save RAM
* show tx stats on QCA9880
* new qcom,ath10k-calibration-variant DT entry
* WMI layer support for wcn3990
ath9k
* new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM
wcn36xx
* hardware scan offload support
wil6210
* run-time PM support when interface is down
iwlwifi
* initial work for rate-scaling offload
* Support for new FW API version 36
* Rename the temporary hw name A000 to 22000
ssb
* make SSB a menuconfig to ease disabling it all
mwl8k
* enable non-DFS 5G channels 149-165
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* Rename the temporary name A000 to 22000;
* Change in the way we print the firmware version;
* Remove some unused code;
* Other small improvements;
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEF3LNfgb2BPWm68smoUecoho8xfoFAloea/wACgkQoUecoho8
xfr7SA/9FKFcgKFQrF6aUlMBv09NttoyyLZcFspSkVQb0r7CkNJZT+t8eMg3nzCD
atoLqH41cI8x7OoAyiFv6FJVi+5TqEAGd9GuOVxARN8vVOtgwCQc18CoyXxjcqYE
Dw6Nb55H+Dro/9ucYo4f0VC2unVOeBZlEUnJrImctKCMIECWcrDaqdp9BwzxUp3p
y3mO33izj8p+fjp/qQnbWapIZILi/K/XMQv/Q7LmLXddq7hmVNhVLezbEj29a0wl
kCfzO0UQ2fUa8fWrCrg2QXfjWLsOjLUjfrt/Dm5HH4iTa4CuSvv/+2JA88S3V/TB
I0pwqkUq+N1XZC62efYP6TmTl4+Xag1nUNHl7njofxNDYZ2xq3ocCxhzdMF6O1eW
++RuzIhz71e/U07NoJ83GcPxbzsv1BO2Y+6kZMygUq6EKsfWsDRUOWsM7lZ088Vl
YtmU2PU8OgXBSo5QFNKjt3d4G1dJ7CvLkCAb1aQSQ/V8YrSHHxTpxpWCXGC/GSCs
jm4XDj4oDQMgKtq1PzaR/rVn1+8jzxPHcjGMtFzirDrGDwdpgsZDRK2YZb6KrKvu
1RS5M/WsCj2Jld7Ws+h/IbVVmMIG8RPVxgGQwqGCWEZbp6QNW6M72wcgO+jzUsQ+
COidUDnMiRzRWRaAta0wrUBU4dKVOiEPJJdTRX6G4Cd8dHSVlfI=
=j1dk
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First batch of iwlwifi updates for v4.16
* Rename the temporary name A000 to 22000;
* Change in the way we print the firmware version;
* Remove some unused code;
* Other small improvements;
kvalo:
There were conflicts, I fixed them with taking into account commit c2c48ddfc8
("iwlwifi: fix firmware names for 9000 and A000 series hw"):
CONFLICT (content): Merge conflict in drivers/net/wireless/intel/iwlwifi/iwl-config.h
CONFLICT (modify/delete): drivers/net/wireless/intel/iwlwifi/cfg/a000.c deleted in ca495785063c428641cc6df8888afd2587ca6677 and modified in HEAD. Version HEAD of drivers/net/wireless/intel/iwlwifi/cfg/a000.c left in tree.
The family name A000 was just a place-holder when we didn't know what
the official name would be yet. Now we know that the family name is
22000, so rename all occurrences accordingly.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When getting HW rfkill we get stop_device being called from
two paths.
One path is the IRQ calling stop device, and updating op
mode and stack.
As a result, cfg80211 is running rfkill sync work that shuts
down all devices (second path).
In the second path, we eventually get to iwl_mvm_stop_device
which calls iwl_fw_dump_conf_clear->iwl_fw_dbg_stop_recording,
that access periphery registers.
The device may be stopped at this point from the first path,
which will result with a failure to access those registers.
Simply checking for the trans status is insufficient, since
the race will still exist, only minimized.
Instead, move the stop from iwl_fw_dump_conf_clear (which is
getting called only from stop path) to the transport stop
device function, where the access is always safe.
This has the added value, of actually stopping dbgc before
stopping device even when the stop is initiated from the
transport.
Fixes: 1efc3843a4 ("iwlwifi: stop dbgc recording before stopping DMA")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Current pci dumping code code is always falling to the error
path, resulting with a constant "Read failed" message, also
for the successful reads.
Fixes: a5c932e41fdd ("iwlwifi: pcie: dump registers when HW becomes inaccessible")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Maintain the TCP retransmit queue using an rbtree, with 1GB
windows at 100Gb this really has become necessary. From Eric
Dumazet.
2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.
3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
Lunn.
4) Add meter action support to openvswitch, from Andy Zhou.
5) Add a data meta pointer for BPF accessible packets, from Daniel
Borkmann.
6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.
7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.
8) More work to move the RTNL mutex down, from Florian Westphal.
9) Add 'bpftool' utility, to help with bpf program introspection.
From Jakub Kicinski.
10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
Dangaard Brouer.
11) Support 'blocks' of transformations in the packet scheduler which
can span multiple network devices, from Jiri Pirko.
12) TC flower offload support in cxgb4, from Kumar Sanghvi.
13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
Leitner.
14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.
15) Add RED qdisc offloadability, and use it in mlxsw driver. From
Nogah Frankel.
16) eBPF based device controller for cgroup v2, from Roman Gushchin.
17) Add some fundamental tracepoints for TCP, from Song Liu.
18) Remove garbage collection from ipv6 route layer, this is a
significant accomplishment. From Wei Wang.
19) Add multicast route offload support to mlxsw, from Yotam Gigi"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
tcp: highest_sack fix
geneve: fix fill_info when link down
bpf: fix lockdep splat
net: cdc_ncm: GetNtbFormat endian fix
openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
netem: remove unnecessary 64 bit modulus
netem: use 64 bit divide by rate
tcp: Namespace-ify sysctl_tcp_default_congestion_control
net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
ipv6: set all.accept_dad to 0 by default
uapi: fix linux/tls.h userspace compilation error
usbnet: ipheth: prevent TX queue timeouts when device not ready
vhost_net: conditionally enable tx polling
uapi: fix linux/rxrpc.h userspace compilation errors
net: stmmac: fix LPI transitioning for dwmac4
atm: horizon: Fix irq release error
net-sysfs: trigger netlink notification on ifalias change via sysfs
openvswitch: Using kfree_rcu() to simplify the code
openvswitch: Make local function ovs_nsh_key_attr_size() static
openvswitch: Fix return value check in ovs_meter_cmd_features()
...
Commit a6d24fad00 ("iwlwifi: pcie: dump registers when HW becomes
inaccessible") added a function to dump pcie config registers and
memory mapped registers on a failure. It is currently only accessible
within trans.c. Add it to struct iwl_trans_ops, so that failure cases
in other files can call it. While there, add a call to this function
from iwl_pcie_load_firmware_chunk in pcie/tx.c, since this is a common
failure case seen on some platforms.
Signed-off-by: Kirtika Ruchandani <kirtika@chromium.org>
[modified the commit message slightly]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We conclude the HW became inaccessible when we timeout waiting for
a bit to be set in a memory mapped register (CSR_GP_CNTRL). This
conclusion may not be true because the bit may not get set due to:
- a firmware issue
- a driver issue
- a PCI bus issue
- a platform issue
There are a lot of such reports with really no good debug information
beyond this message to help us.
Add some debug information and attempt to dump the different register
spaces at such a failure:
* Dump some configuration space of device - this will tell us if
something very basic is broken in the PCIe bus (so that configuration
accesses are failing). If this works, the PCIe bus seems OK. If this
does not work, it is definitely an PCIe issue.
* Dump some memory mapped registers - if we're reading some sane'ish
values, this will tell us that the PCIe bus is OK, but may be a firmware
/ driver issue. If this does not work, it may be a PCI configuration
issue or a driver/firmware issue.
* Dump parent and device's AER registers, will give us some straws to
chew on.
This is the sample output:
[ 13.082651] ------------[ cut here ]------------
[ 13.086791] iwlwifi 0000:01:00.0: iwlwifi transaction failed, dumping registers
[ 13.086793] iwlwifi 0000:01:00.0: iwlwifi device config registers:
[ 13.086893] iwlwifi 0000:01:00.0: 00000000: 095a8086 00100406 02800059 00000000 00000004 00000000 00000000 00000000
[ 13.086895] iwlwifi 0000:01:00.0: 00000020: 00000000 00000000 00000000 50108086 00000000 000000c8 00000000 00000100
[ 13.086901] iwlwifi 0000:01:00.0: iwlwifi device memory mapped registers:
[ 13.086989] iwlwifi 0000:01:00.0: 00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 13.086991] iwlwifi 0000:01:00.0: 00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 13.086999] iwlwifi 0000:01:00.0: iwlwifi device AER capability structure:
[ 13.087033] iwlwifi 0000:01:00.0: 00000000: 14010001 00100000 00000000 00462031 00002000 00002000 00000014 40000001
[ 13.087034] iwlwifi 0000:01:00.0: 00000020: 0000000f d140000c 00000000
[ 13.087036] iwlwifi 0000:01:00.0: iwlwifi parent port (0000:00:1c.0) config registers:
[ 13.087074] iwlwifi 0000:00:1c.0: 00000000: 9d108086 00100506 060400f1 00810010 00000000 00000000 00010100 200000f0
[ 13.087075] iwlwifi 0000:00:1c.0: 00000020: d140d140 0001fff1 00000000 00000000 00000000 00000040 00000000 0006010b
[ 13.087087] ------------[ cut here ]------------
[ 13.087095] WARNING: CPU: 0 PID: 1759 at drivers/net/wireless/iwl7000/iwlwifi/pcie/trans.c:2082 iwl_trans_pcie_reclaim+0x1ee4/0x2b9a [iwlwifi]()
[ 13.087096] Timeout waiting for hardware access (CSR_GP_CNTRL 0xffffffff)
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Work queues cannot be allocated when a mutex is held because the mutex
may be in use and that would make it sleep. Doing so generates the
following splat with 4.13+:
[ 19.513298] ======================================================
[ 19.513429] WARNING: possible circular locking dependency detected
[ 19.513557] 4.13.0-rc5+ #6 Not tainted
[ 19.513638] ------------------------------------------------------
[ 19.513767] cpuhp/0/12 is trying to acquire lock:
[ 19.513867] (&tz->lock){+.+.+.}, at: [<ffffffff924afebb>] thermal_zone_get_temp+0x5b/0xb0
[ 19.514047]
[ 19.514047] but task is already holding lock:
[ 19.514166] (cpuhp_state){+.+.+.}, at: [<ffffffff91cc4baa>] cpuhp_thread_fun+0x3a/0x210
[ 19.514338]
[ 19.514338] which lock already depends on the new lock.
This lock dependency already existed with previous kernel versions,
but it was not detected until commit 49dfe2a677 ("cpuhotplug: Link
lock stacks for hotplug callbacks") was introduced.
Reported-by: David Weinehall <david.weinehall@intel.com>
Reported-by: Jiri Kosina <jikos@kernel.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Newer versions of A000 devices come with two diffenent RF modules.
The PCI_ID, the subsystem ID and the RF ID are identical in these two cases,
so we need to differentiate them by using the CSR_HW_RF_ID register-
in order to load the appropriate firmware.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This allows to modify TFD_TX_CMD_SLOTS to a power of 2
which is smaller than 256.
Note that we still need to set values to wrap at 256
into the scheduler's write pointer, but all the rest of
the code can use shorter transmit queues.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are still some references to 3945 and 4965 HW, which were never
supported in iwlwifi. These references were inherited from a previous
project and are irrelevant here. Additionally, remove some irrelevant
references to 5100 HW. Remove all these.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Load FW according to NIC type,
taking into account simulation, if exists.
This is determined by a prph register.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The first wireless-drivers-next pull request for 4.14. I'm submitting
this unusally late in the cycle as my vacation postponed this. But
even if this is late there's not still that much new features, mostly
cleanup or fixes.
Major changes:
ath10k
* preparation for wcn3990 support
iwlwifi
* Reorganization of the code into separate directories continues
qtnfmac
* regulatory support updates
* add get_channel, dump_survey and channel_switch cfg80211 handlers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZiHuQAAoJEG4XJFUm622bVSEIAKdausycC6OOZjwTGWnFyxE/
58n79VTrTbXVLwJ7lSBCGYCTujc7amPxAVlDOLYd+9TKm0fO7gap50Gdl35HO5sp
9v/augHQSouz52q2vgsTi0JbXsqhJQZ4Ie4P0fo8OyqJMYAvFga2FhFBpJseMYd9
NX88SMoxAGgDkTC0JfzzLnA/jZ0W6ULai6zmRE1s6lUIynP2kzHgpfbMH3+KEkod
SUW+yX91MdOkkyFGXyY11uuBqanUpEVSAQXW6J76vw3qS88qIqaL3iIeJ6C4Vozq
fKNkHN4iZOd9FlKY1IFi4vS0+7hWiq6DQ3c+ngtU6cuq1XdBa6PuanC3I2e0B8E=
=PKUU
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-08-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.14
The first wireless-drivers-next pull request for 4.14. I'm submitting
this unusally late in the cycle as my vacation postponed this. But
even if this is late there's not still that much new features, mostly
cleanup or fixes.
Major changes:
ath10k
* preparation for wcn3990 support
iwlwifi
* Reorganization of the code into separate directories continues
qtnfmac
* regulatory support updates
* add get_channel, dump_survey and channel_switch cfg80211 handlers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename this function to the more appropriate iwl_pcie_check_hw_rf_kill()
since it's only a function in the pcie code and cannot be called from
any other place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't set the error code here so we end up returning ERR_PTR(0) which
is NULL. The caller doesn't expect that so it results in a NULL
dereference.
Fixes: 2e5d4a8f61 ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The newest devices need a longer time to reset because of
their more complex hardware. Wait 5ms after device reset.
Consolidate all the places that reset the device in the
PCIe transport to avoid future bugs.
While at it, unify the flow to use set_bit instead of full
write as requested by the hardware designers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_pcie_apm_init can fail so make sure that the caller
takes the status into account.
Also, ensure that the error that iwl_pcie_apm_init can emit
will appear in the kernel log by default.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's a lot of mvm code that really should be more generic
and part of the iwlwifi module. Start by making a place to
keep such code - in the new "fw" subdirectory - and already
move the firmware related header files there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In some platforms, having the device enabled with certain radio
frontends causes the platform to not be able to resume properly
from suspend, regardless of the wakeup cause. This was traced to
a hardware issue with the integrated 9000-series A-step variant.
Set the right hardware bit to disable the problematic state.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver prints "L1 Enabled - LTR Enabled" all the time as dev_info,
which is just useless noise in most cases. Convert this to
IWL_DEBUG_POWER() so we don't pollute the log unnecessarily but still
can get this info on demand.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Nothing ever checks the return value of iwl_pcie_apm_stop_master(),
so there's no point in it having one - make it return void.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use kstrtou32_from_user() in debugfs instead of open-coding it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't actually care about the value at all, just making sure
that we can successfully parse a single integer value, but that's
entirely pointless - remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When toggling the RF-kill pin quickly in succession, the driver can
get rather confused because it might be in the process of shutting
down, expecting all commands to go through quickly due to rfkill,
but the transport already thinks the device is accessible again,
even though it previously shut it down. This leads to bugs, and I
even observed a kernel panic.
Avoid this by making the PCIe code only report that the radio is
enabled again after the higher layers actually decided to shut it
off.
This also pulls out this common RF-kill checking code into a common
function called by both transport generations and also moves it to
the direct method - in the internal helper we don't really care
about the RF-kill status anymore since we won't report it up until
the stop anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to debug "hardware" RF-kill flows, add a low-level hook to
allow changing the "hardware" RF-kill from debugfs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* Loads of FW API documentation improvements (for tools and htmldoc);
* Continued work for the new A000 family;
* Bumped the maximum supported FW API to 31;
* Improve the differentiation between 8000, 9000 and A000 families;
* A lot of fixes and cleanups here and there;
-----BEGIN PGP SIGNATURE-----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=oYeO
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-06-06' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First batch of iwlwifi driver patches 4.13
* Loads of FW API documentation improvements (for tools and htmldoc);
* Continued work for the new A000 family;
* Bumped the maximum supported FW API to 31;
* Improve the differentiation between 8000, 9000 and A000 families;
* A lot of fixes and cleanups here and there;
kvalo: There were conflicts iwl_mvm_stop_device() and
iwl_mvm_tcool_set_cur_state(). The former was easy but latter needed more
thought. Apparently the mutex was taken too late, so I fixed so that the mutex
is taken first and then check for iwl_mvm_firmware_running().
FH in A000 HW are placed in a different location,
and need to be read as prph, rather than direct.
Support A000 dumping as well as legacy.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add two new device families to differentiate them from 8000.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We only need to handle d0i3 entry and exit during suspend resume if
system_pm is set to IWL_PLAT_PM_MODE_D0I3, otherwise d0i3 entry
failures will cause suspend to fail.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=194791
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that we have 512 queues, add a wait for single TX
queue to gen2.
This replaces gen1 wait_tx_queues_empty, which was limited
to 32 queues.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In gen2, page dumping needs to be done in the trans
layer, as it is the one with access to the paging
pointers.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Rename current wait_tx_queue_empty to wait_tx_queues_empty since
it waits for multiple queues (up to 32).
Next patch will add a wait for single TX queue which is needed for
gen2 to be scalable for 512.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This struct member is already assigned in the previous
call to iwl_trans_alloc(), so assigning the same value
again is superfluous - remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Change queue allocation to be dynamic. On transport init only
the command queue is being allocated. Other queues are allocated
on demand.
This is due to the huge amount of queues we will soon enable (512)
and as a preparation for TX Virtual Queue Manager feature (TVQM),
where firmware will assign the actual queue number on demand.
This includes also allocation of the byte count table per queue
and not as a contiguous chunk of memory.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This function is basically the same as gen1, except for clean
ups of old devices configuration that are never used in a000
configuration.
It will also help with refactoring rf_kill later on.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In a000 transport we will allocate queues dynamically.
Right now queue are allocated as one big chunk of memory
and accessed as such.
The dynamic allocation of the queues will require accessing
the queues as pointers.
In order to keep simplicity of pre-a000 tx queues handling,
keep allocating and freeing the memory in the same style,
but move to access the queues in the various functions as
individual pointers.
Dynamic allocation for the a000 devices will be in a separate
patch.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New transport will be used only by op modes that supports
buffer station offload - hence those will never be called.
Clean it up.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Code is basically the same, with a cleanups of old narrow host
command, ampg workarounds, some cosmetic stuff, and usage of
TFH functions when accessing TFD queues.
This enables also the cleanup of iwl_pcie_tfd_set_tb() since
now it won't be called anywhere in the a000 data path
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is just a copy-paste in order to make changes tracking
easier.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In a000 devices the TX handling is different in a few ways:
* Queues are allocated dynamically
* DQA is enabled by default
* Driver shouldn't access TFH registers - ucode configures it
all in SCD_QUEUE_CFG command
Support all this in a new API with op mode, where op mode sends
the command, transport will allocate the queue dynamically, fill
in DMA properties, send the command to FW and get the ID back.
Current implementation only sets the new transport API and fills
the DMA properties.
Future patches will complete the other parts.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Context information structure is going to be used in a000
devices for firmware self init.
The self init includes firmware self loading from DRAM by
ROM.
This means the TFH relevant firmware loading can be cleaned up.
The firmware loading includes the paging memory as well, so op
mode can stop initializing the paging and sending the DRAM_BLOCK_CMD.
Firmware is doing RFH, TFH and SCD configuration, while driver
only fills the required configurations and addresses in the
context information structure.
The only remaining access to RFH is the write pointer, which
is updated upon alive interrupt after FW configured the RFH.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
a000 devices are going to have a lot of flows simplified
and changed: init flow, RX, TX, and more.
This, combined with the fact that code is already very
complicated due to backward compatibility - introduce
a split that will enable to introduce simplified version
of functions.
Shared ops are moved to a macro, while functions that will
be updated in the next patches are defined twice for now.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't need this parameter anymore, since we always pass 0 anyway.
Remove it from the structure and from all the relevant functions.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This register is helpful for debugging D3 issues.
Driver turns all bits on, and then on exit reads the
updated value there.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This reverts commit 8aacf4b73f ("iwlwifi: introduce trans API
to get byte count table").
The commit is not needed as a better approach will be taken.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't need to print so much data in the kernel log.
Limit the data to be printed to the queue that actually
got stuck in case of a TFD queue hang, and stop dumping
all the CSR and FH registers. Over the course of time, the
CSR and FH values haven't proven themselves to be really
useful for debugging, and they are now in the firmware dump
anyway.
This comes as a preparation to the addition of more data
required to be printed by the firwmare team.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When getting RF_KILL and disabling radio, the device gets stopped
and reset. This erases the IVAR table that matches the interrupt
to its cause, and is essential for MSIX proper functionality.
Till now, the table wasn't re-configured after the reset, and
therefore the interrupt that enabled radio didn't fire on the
right irq, and the driver didn't handle it correctly.
To fix this, configure the IVAR table again after resetting the
device.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During the suspend/resume flow some HW blocks are reset. This causes
the IVAR table to be completely erased. This table is where interrupt
causes are bound to specific IRQs. When the table is empty the
interrupt handlers are not called correctly. Fix this by reconfiguring
the IVAR table after resume.
Fixes: 2e5d4a8f61 ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The MSIX configuration flow includes two different stages:
configuring the HW by writing to the IVAR table and configuring the SW
to reflect the HW configuration.
The HW configuration is needed on each HW reset,
whereas the SW configuration is only needed during the init flow.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
msix configuration functions should be called by other functions.
For example by pcie_d3_resume, move it above to enable it.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Our 9000 device supports 64 bit DMA address for RX only, and
not for TX.
Setting DMA mask to 64 for the whole device is erroneous - we
can do it only for a000 devices where device is capable of
both RX & TX DMA with 64 bit address space.
Fixes: 96a6497bc3 ("iwlwifi: pcie: add 9000 series multi queue rx DMA support")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
shift_param is defined and set in iwl_pcie_load_cpu_sections but not
used. Fix this to avoid -Wunused-but-set-variable warning.
The code using it turned into dead code with commit dcab8ecd56
("iwlwifi: mvm: support ucode load for family_8000 B0 only") which
added a separate function iwl_pcie_load_given_ucode_8000 (then 8000b)
for IWL_DEVICE_FAMILY_8000. Commit 76f8c0e17e ("iwlwifi: pcie:
remove dead code") removed the dead code but left shift_param as is.
iwlwifi/pcie/trans.c: In function ‘iwl_pcie_load_cpu_sections’:
iwlwifi/pcie/trans.c:871:6: warning: variable ‘shift_param’ set but not used [-Wunused-but-set-variable]
Fixes: dcab8ecd56 ("iwlwifi: mvm: support ucode load for family_8000 B0 only")
Fixes: 76f8c0e17e ("iwlwifi: pcie: remove dead code")
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Cc: Sara Sharon <sara.sharon@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Liad Kaufman <liad.kaufman@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[removed some unnecessary braces]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The maximum number of firmware sections is now 32 instead of 16 for
a000 devices. Set the appropriate define. Avoid out of bounds access
in case there are more sections than the maximum set by driver.
Make the driver extensible to FW size changes by allocating the
section memory dynamically.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of passing DRV_NAME pass a string that
represents the reason for the interrupt.
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Due to firmware design considerations, move to wide ID for
all commands.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In MSIX mode the number of irq depends on the number of
possible cpus existing on the host.
This cause to bug in case there are offline cores.
Take into account only the online CPUs instead.
Also save it in temporary variable.
Fixes: commit 2e5d4a8f61 ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Function is very indented. Go to msi section if needed to avoid
it and by that make the code more readable.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to utilize the host's CPUs in the most efficient way
we bind each rx interrupt vector to each CPU on the host.
Each rx interrupt is prioritized to execute only on the designated CPU
rather than any CPU.
Processor affinity takes advantage of the fact that some remnants of
a process that was run on a given processor may remain in that
processor's memory state for example, data in the CPU cache after
another process is run on that CPU. Scheduling that process to execute
on the same processor could result in an efficient use of process by
reducing performance-degrading situations such as cache misses
and parallel processing.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case the OS provides fewer interrupts than requested, different
causes will share the same interrupt vector as follow:
1.One interrupt less: non rx causes shared with FBQ.
2.Two interrupts less: non rx causes shared with FBQ and RSS.
3.More than two interrupts: we will use fewer RSS queues.
Also make the request depend on the number of online CPUs
instead of possible CPUs.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The original intent was to have the general iwl_queue shared
between RX and TX queues, but it is not the actual status.
Since it is not shared with any struct but iwl_txq, it adds
unnecessary complexity. Merge those structs.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Previous patch introduced the new formats. This patch
allocates the new structures and adjusts code accordingly.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In future HW the byte count table address will be configured
by ucode per queue. Add API to expose the byte count table to
the opmode
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New hardware supports bigger TFDs and TBs.
Introduce the new formats and adjust defines and code
relying on old format.
Changing the actual TFD allocation is trickier and
deferred to the next patch.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If device family is 8000 then iwl_pcie_load_cpu_sections()
won't be called at all (iwl_pcie_load_cpu_sections_8000() is
called in that case) so this piece of code never gets called.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Turns out we should access TFH relative addresses.
Also, the FH_UCODE_LOAD_STATUS was replaced by
UREG_UCODE_LOAD_STATUS.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Up till now we accessed SCD configuration only for initial
configuration and for enabling command queue.
For a000 generation the command queue is open by default
and firmware configures the rest. No driver SCD accesses
are expected. Make sure this is the case.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Centralize the logging of SCD status. The motivation is
that for a000 devices we will have new SCD HW, but this
code was duplicate anyway, so it is a proper cleanup.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Upon firmware load interrupt (FH_TX), the ISR re-enables the
firmware load interrupt only to avoid races with other
flows as described in the commit below. When the firmware
is completely loaded, the thread that is loading the
firmware will enable all the interrupts to make sure that
the driver gets the ALIVE interrupt.
The problem with that is that the thread that is loading
the firmware is actually racing against the ISR and we can
get to the following situation:
CPU0 CPU1
iwl_pcie_load_given_ucode
...
iwl_pcie_load_firmware_chunk
wait_for_interrupt
<interrupt>
ISR handles CSR_INT_BIT_FH_TX
ISR wakes up the thread on CPU0
/* enable all the interrupts
* to get the ALIVE interrupt
*/
iwl_enable_interrupts
ISR re-enables CSR_INT_BIT_FH_TX only
/* start the firmware */
iwl_write32(trans, CSR_RESET, 0);
BUG! ALIVE interrupt will never arrive since it has been
masked by CPU1.
In order to fix that, change the ISR to first check if
STATUS_INT_ENABLED is set. If so, re-enable all the
interrupts. If STATUS_INT_ENABLED is clear, then we can
check what specific interrupt happened and re-enable only
that specific interrupt (RFKILL or FH_TX).
All the credit for the analysis goes to Kirtika who did the
actual debugging work.
Cc: <stable@vger.kernel.org> [4.5+]
Fixes: a6bd005fe9 ("iwlwifi: pcie: fix RF-Kill vs. firmware load race")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The PCIe transport needs to store two pointers in each TX SKB, and
currently assumes mac80211's ieee80211_tx_info is present in the CB
to do that.
In order to remove that assumption, have the opmodes pass in the
offset to where the pointers can be stored in the CB and use the
offset in the PCIe code.
To make the disentanglement complete, remove mac80211.h includes
from everywhere in the generic iwlwifi code. This required adding
an include of cfg80211.h in one place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On some of the chipsets MSI & INTA interrupts are disabled by default in
the HW registers, and need to be explicitly enabled to be used.
In case MSI-X isn't used, make sure MSI mode is enabled by setting
the relevant HW register.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The NIC's CPU gets started after the firmware has been
written to its memory. The first thing it does is to
send an interrupt to let the driver know that it is
running. In order to get that interrupt, the driver needs
to make sure it is not masked. Of course, the interrupt
needs to be enabled in the driver before the CPU starts to
run.
I mistakenly inversed those two steps leading to races
which prevented the driver from getting the alive interrupt
from the firmware.
Fix that.
Cc: <stable@vger.kernel.org> [4.5+]
Fixes: a6bd005fe9 ("iwlwifi: pcie: fix RF-Kill vs. firmware load race")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support DQA queue sharing when no free queue exists for
allocation to a STA that already exists. This means that
a single queue will serve more than a single TID (although
the RA will be the same for all TIDs served).
We try to choose the lowest AC possible, to ensure the
shared queues have the lowest possible combined AC
requirements. The queue to share is chosen only from the
same RA's DATA queues as follows (in descending priority):
1. An AC_BE queue
2. Same AC queue
3. Highest AC queue that is lower than new AC
4. Any existing AC (there always is at least 1 DATA queue)
If any aggregations existed for any of the TIDs of the
shared queue - they are stopped (the FW is notified), but
no delBA is sent.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Integrated 9000 devices have a bug with shadow registers
value retention.
If driver writes RBD registers while MAC is asleep the
values are stored in shadow registers to be copied whenever
MAC wakes up.
However, in 9000 devices a MAC wakeup is not triggered
and when the bus powers down due to inactivity the shadow
values and dirty bits are lost.
Turn on the chicken-bits that cause MAC wakeup for RX-related
values as well when the device is in D0.
When the device is in low power mode turn the RX wakeup chicken
bits off since driver is idle and this W/A is not needed.
Remove previous W/A which was ineffective.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since msleep is based on jiffies, it can sleep for a long time.
Use usleep_range() instead to shorten the maximum time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Newer hardware generations will take longer to be accessible again
after reset, so we need to wait longer before continuing any flow
that did a reset.
Rather than make the wait time configurable, simply extend it for
all.
Since all of these code paths can sleep, use usleep_range() rather
than mdelay().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since we have a lot of configuration structs (almost 70) saving
some memory in each one of them leads to an overall saving of
~2.6KiB of memory.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently there is one to one function between device id to it's ucode.
The new generation devices allows to combine different phy and mac images.
Now we have two different ucode images with the same device id.
Read RF ID to identify phy image and overwrite it if needed.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It's cleaner to always call the iwl_trans_ref/unref() functions
instead of sometimes calling the trans-specific ops directly. This
also prepares for moving some of the code from the trans-specific ops
to the common trans code.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In MSIX mode we iterate over the allocated interrupt vectors and
register them to an handler. In case of registration failure,
we free all the allocated irq.
we use the outer index mistakenly instead of the inner one.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We want to request an interrupt vector for RSS queue per CPU,
one vector for fallback queue, and one for non-rx interrupts.
Future patch will make sure that no RSS traffic is directed to
fallback queue.
This will enable us to enable fast path on traffic that otherwise
would have been received on the fallback queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Bjorn pointed out that printing an error value as an
hexadecimal isn't very convenient. Change that.
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We don't use the refcount value anymore, all the refcounting is done
in the runtime PM usage_count value. Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When entering suspend the driver calls iwl_disable_interrupts() and
then iwl_pcie_disable_ict().
On resume the driver calls only iwl_pcie_reset_ict() without calling
explicitly to iwl_enable_interrupts().
This mostly works since iwl_pcie_reset_ict is calling to
iwl_enable_interrupts, but it doesn't work when there is no ict_table
in MSIx mode.
The result is that driver tries to resume but fails since it doesn't
get the RX interrupt from FW indicating that d0i3 exit was completed.
Fix it by adding an explicit call to enable interrupts.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
IWL_INFO is not an error but still printed by default.
"can't access the RSA semaphore it is write protected" seems
worrisome but it is not really a problem.
CC: <stable@vger.kernel.org> [4.1+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The pci driver keeps any unbound device in active state and forbids
runtime PM. When our driver gets probed, we take control of the
state. When the device is released (i.e. during unbind or module
removal), we should return the state to what it was before. To do so,
we need to forbid RTPM in the driver remove op.
Additionally, remove an unnecessary pm_runtime_disable() call, move
the initial ref_count setting to a better place and add some comments
explaining what is going on.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Working with MSIX requires prior configuration.
This includes requesting interrupt vectors from the OS,
registering the vectors and mapping the optional causes to the
relevant interrupt. In addition add new interrupt handler
to handle MSIX interrupt.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of waking up the device each time we write a
register, wake it up once, and writes the registers
at once.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These are a few fixes for the current cycle.
3 out of the 5 patches fix a bugzilla.
* fix a race that users reported when we try to load the firmware
and the hardware rfkill interrupt triggers at the same time.
* Luca fixes a very visible bug in scheduled scan: our firmware
doesn't support scheduled scan with no profile configured and
the supplicant sometimes requests such scheduled scans.
* build system fix
* firmware name update for 8265
* typo fix in return value
The iwl_trans_pcie_start_fw() function may return the positive value EIO
instead of -EIO in case of error.
Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When we load the firmware, we hold trans_pcie->mutex to
avoid nested flows. We also rely on the ISR to wake up the
thread when the DMA has finished copying a chunk. During
this flow, we enable the RF-Kill interrupt.
The problem is that the RF-Kill interrupt handler can take
the mutex and bring the device down. This means that if
we load the firmware while the RF-Kill switch is enabled
(which will happen when we load the INIT firmware to read
the device's capabilities and register to mac80211), we
may get an RF-Kill interrupt immediately and the ISR will
be waiting for the mutex held by the thread that is
currently loading the firmware. At this stage, the ISR
won't be able to service the DMA's interrupt needed to
wake up the thread that load the firmware. We are in a
deadlock situation which ends when the thread that loads
the firmware fails on timeout and releases the mutex.
To fix this, take the mutex later in the flow, disable
the interrupts and synchronize_irq() to give a chance to
the RF-Kill interrupt to run and complete.
After that, mask all the interrupts besides the DMA
interrupt and proceed with firmware load. Make sure to
check that there was no RF-Kill interrupt when the
interrupts were disabled.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=111361
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Previous patches enabled new 9000 hardware DMA for one queue
only.
Enable the actual multi-queue path and configuration now.
This requires also per-queue NAPI struct.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently when the driver is configured with wowlan parameters, and enters
D3 mode, the driver switches the FW image to D3, and when it exists
suspend, it reloads the D0 image.
If the firmware supports the consolidation of the D0 & D3 images there is
no need to load the D3 image on suspend, and no need to reload the D0
image on resume.
Do not switch images on suspend / resume, for firmwares that support
consolidated images.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable runtime power management (RTPM) for PCIe devices and implement
the corresponding functions to enable D0i3 mode when the device is
idle.
Additionally, remove some unnecessary #ifdef's because the RTPM code
will not be called if runtime PM is not configured.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add an initial implementation of runtime power management (RTPM) for
PCI devices. With this patch, RTPM is only used when wifi is off
(i.e. the wifi interface is down). This implementation is behind a
new Kconfig flag, IWLWIFI_PCIE_RTPM.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The 9000 series introduces several changes in the device
DMA operation.
As the device now supports multi-queue rx, several DMA channels
should be configured.
The flows of providing the device with the allocated RBDs now
changes as well - the device maintains a separate table of used
and free table.
The hardware may use the free table to feed RBDs to any queue.
This requires maintaing a shared table to map returned RBDs to
the original RXB - for that purpose the VID is introduced - an
internal identifier of the RB placed in the lower 12 bits and
returned by HW in the used data.
Another change is the support of 64 bit DMA address.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The 9000 series devices will support multi rx queues.
Current code has one static rx queue - change it to allocate
a number of queues per the device capability (pre-9000 devices
have the number of rx queues set to one).
Subsequent generalizations are:
Change the code to access an explicit numbered rx queue only
when the queue number is known - when handling interrupt, when
accessing the default queue and when iterating the queues.
The rest of the functions will receive the rx queue as a pointer.
Generalize the warning in allocation failure to consider the
allocator status instead of a single rx queue status.
Move the rx initial pool of memory buffers to be shared among
all the queues and allocated to the default queue on init.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
8000 device family has a new debug engine that needs to be
configured differently than 7000's.
The debug engine's DMA works in chunks of memory and the
size of the buffer really means the start of the last
chunk. Since one chunk is 256-byte long, we should
configure the device to write to buffer_size - 256.
This fixes a situation were the device would write to
memory it is not allowed to access.
CC: <stable@vger.kernel.org> [4.1+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The debug functions of fw-dbg.c don't really need to modify
the trigger and the description they receive as a parameter.
Constify the pointers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the op_mode sends an skb whose payload is bigger than
MSS, PCIe will create an A-MSDU out of it. PCIe assumes
that the skb that is coming from the op_mode can fit in one
A-MSDU. It is the op_mode's responsibility to make sure
that this guarantee holds.
Additional headers need to be built for the subframes.
The TSO core code takes care of the IP / TCP headers and
the driver takes care of the 802.11 subframe headers.
These headers are stored on a per-cpu page that is re-used
for all the packets handled on that same CPU. Each skb
holds a reference to that page and releases the page when
it is reclaimed. When the page gets full, it is released
and a new one is allocated.
Since any SKB that doesn't go through the fast-xmit path
of mac80211 will be segmented, we can assume here that the
packet is not WEP / TKIP and has a proper SNAP header.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Allow to configure the driver to pretend to have TX CSUM
offload support. This will be useful to test the TSO flows
that will come in further patches.
This configuration is disabled by default.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
ilw@linux.intel.com is not available anymore.
linuxwifi@intel.com should be used instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The d0i3_mode variable is used to distinguish between transports that
handle d0i3 entry during suspend by themselves (i.e. the slave
transports) and those which rely on the op_mode layer to do it. The
reason why the former do it by themselves is that they need to
transition from d0i3 in runtime_suspend into d0i3 in system-wide
suspend and this transition needs to happen before the op_mode's
suspend flow is called.
The wowlan_d0i3 element is also a bit confusing, because it just
reflects the wowlan->any value for the trans to understand. This is a
bit unclear in the code and not generic enough for future use.
To make it clearer and to generalize the platform power mode settings,
introduce two variables to indicate the platform power management
modes used by the transport.
Additionally, in order not to take too big a step in one patch, treat
this new variables semantically in the same way as the old d0i3_mode
element, introducing a iwl_mvm_enter_d0i3_on_suspend() function to
help with that.
This commit also adds the foundation for a new concept where the
firmware configuration state (i.e. D0, D3 or D0i3) is abstracted from
the platform PM mode we are in (i.e. runtime suspend or system-wide
suspend).
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Host commands now have a group id, express this in printed messages.
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In certain flows (see next patches), the op_mode may need to
block the Tx queues for a short period. Provide an API for
that. The transport is in charge of counting the number of
times the queues are blocked since the op_mode may block the
queues several times in a row before unblocking them.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Transport code currently calls itself through the transport ops,
which is quite pointless. Clean up all of this. While at it,
remove the unnecessary dir argument and the redundant IDI code.
In slave transports, call both the common slave debugfs and the
transport's own. SDIO has no files, so remove it all there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently the prph registers dump is in the transport layer,
and each bus needs an additional dump implementation.
Move the prph dump outside transport, and allow a common
implementation for all of the buses.
This is possible because prph base addresses are similar for
all buses.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Expose _no_grab prph i/o functions that allow performing i/o
outside the transport, without requiring grab and release NIC access
for each operation. In addition, rename the functions so they reflect
their non-grabbing behavior.
This can be very useful for consecutive prph i/o operation that occur
outside trans, such as fw dumps.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
802.11ac allows A-MSDU that can be up to 12KB long. Since
an entire A-MSDU needs to fit into one single Receive
Buffer (RB), add support for big RBs.
Since this adds lots of pressure to the memory manager and
significantly increase the true_size of the RX buffers,
don't enable this by default.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
