Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ath9k_wmi_cmd, the allocated network buffer needs to be released
if timeout happens. Otherwise memory will be leaked.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In htc_config_pipe_credits, htc_setup_complete, and htc_connect_service
if time out happens, the allocated buffer needs to be released.
Otherwise there will be memory leak.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath9k_reg_rmw_single do not need return value to cope with different
cases. And change functon return type to void.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initialize acktimeout to the maximum configurable value in
ath_dynack_reset in order to not disconnect long distance static links
enabling dynack and even to take care of possible errors configuring
a static timeout. Moreover initialize station timeout value to the current
acktimeout value
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Compute maximum configurable ackimeout/ctstimeout according to channel
width (clockrate)
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add compute timeout to last computation timestamp in
ath_dynack_reset in order to not run ath_dynack_compute_ackto
immediately
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce ath_dynack_set_timeout routine to configure slottime/ack/cts
timeouts and remove duplicated code
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Atheros cards with a AR92XX generation (and older) chip usually
store their pci(e) initialization vectors on an external eeprom chip.
However these chips technically don't need the eeprom chip attached,
the AR9280 Datasheet in section "6.1.2 DEVICE_ID" describes that
"... if the EEPROM content is not valid, a value of 0xFF1C returns
when read from the register". So, they will show up on the system's
pci bus. However in that state, ath9k can't load, since it relies
on having the correct pci-id, otherwise it doesn't know what chip it
actually is. This happens on many embedded devices like routers
and accesspoint since they want to keep the BOM low and store the
pci(e) initialization vectors together with the calibration data
on the system's FLASH, which is out of reach of the ath9k chip.
Furthermore, Some devices (like the Cisco Meraki Z1 Cloud Managed
Teleworker Gateway) need to be able to initialize the PCIe wifi device.
Normally, this should be done as a pci quirk during the early stages of
booting linux. However, this isn't possible for devices which have the
init code for the Atheros chip stored on NAND in an UBI volume.
Hence, this module can be used to initialize the chip when the
user-space is ready to extract the init code.
Martin Blumenstingl prodived the following fixes:
owl-loader: add support for OWL emulation PCI devices
owl-loader: don't re-scan the bus when ath9k_pci_fixup failed
owl-loader: use dev_* instead of pr_* logging functions
owl-loader: auto-generate the eeprom filename as fallback
owl-loader: add a debug message when swapping the eeprom data
owl-loader: add missing newlines in log messages
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This low level driver can find it useful to get the vif
when a remain on channel session is cancelled.
iwlwifi will need this soon.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20190723180001.5828-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In commit 3c0efb745a ("ath9k: discard undersized packets")
the lower bound of RX packets was set to 10 (min ACK size) to
filter those that would otherwise be treated as invalid at
mac80211.
Alas, short radar pulses are reported as PHY_ERROR frames
with length set to 3. Therefore their detection stopped
working after that commit.
NOTE: ath9k drivers built thereafter will not pass DFS
certification.
This extends the criteria for short packets to explicitly
handle PHY_ERROR frames.
Fixes: 3c0efb745a ("ath9k: discard undersized packets")
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit ec8f24b7fa ("treewide: Add SPDX license identifier -
Makefile/Kconfig") marked various Makefiles and Kconfig files within ath
directories as GPL-2.0. But these modules and drivers are actually ISC:
* ath
* ar5523
* ath10k
* ath5k
* ath6kl
* ath9k
* wcn36xx
* wil6210
Fix SPDX tags accordingly.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There was NVMEM support added to of_get_mac_address, so it could now return
ERR_PTR encoded error values, so we need to adjust all current users of
of_get_mac_address to this new fact.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
AR9330, AR9485, AR9531, AR9550, AR9561 and AR9565 all use same
channel set register configuration which allows for small code
size reduction.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath9k/xmit.c: In function 'ath_tx_count_frames':
drivers/net/wireless/ath/ath9k/xmit.c:413:25: warning: variable 'fi' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/ath/ath9k/xmit.c: In function 'ath_tx_complete_aggr':
drivers/net/wireless/ath/ath9k/xmit.c:449:24: warning: variable 'hdr' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/ath/ath9k/xmit.c: In function 'ath_tx_start':
drivers/net/wireless/ath/ath9k/xmit.c:2274:18: warning: variable 'avp' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/ath/ath9k/xmit.c:2269:24: warning: variable 'hdr' set but not used [-Wunused-but-set-variable]
These variables are not used any more
and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ath9k driver uses as maximum allowed txpower the constant
MAX_RATE_POWER. It is used to set a maximum txpower limit for the PHY
(which is combined txpower) and also the maximum txpower for per chain
rates. Its value 63 is derived from the maximum number the registers can
store for the per chain txpower.
The max txpower a user can set because of this is 31 dBm (floor(63 / 2)).
This also means that a device with multiple tx chains is even limited
further:
* 1 chain: 31 dBm per chain
* 2 chains: 28 dBm per chain
* 3 chains: 26 dBm per chain
This combined txpower limit of 31 dBm becomes even more problematic when
some extra antenna gain is set in the EEPROM. A high power device is then
no longer able to reach its potential limits.
Instead the code dealing with the combined txpower must use a higher limit
than 63 and only the code dealing with the per chain txpower have to use
the limit of 63. Since the antenna gain can be quite large and 8 bit
variables are often used in ath9k for txpower, a large, divisible by two
number like 254 is a good choice for this new limit.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Right now, if an error is encountered during the SREV register
read (i.e. an EIO in ath9k_regread()), that error code gets
passed all the way to __ath9k_hw_init(), where it is visible
during the "Chip rev not supported" message.
ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
ath: phy2: Mac Chip Rev 0x0f.3 is not supported by this driver
ath: phy2: Unable to initialize hardware; initialization status: -95
ath: phy2: Unable to initialize hardware; initialization status: -95
ath9k_htc: Failed to initialize the device
Check for -EIO explicitly in ath9k_hw_read_revisions() and return
a boolean based on the success of the operation. Check for that in
__ath9k_hw_init() and abort with a more debugging-friendly message
if reading the revisions wasn't successful.
ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits
ath: phy2: Failed to read SREV register
ath: phy2: Could not read hardware revision
ath: phy2: Unable to initialize hardware; initialization status: -95
ath: phy2: Unable to initialize hardware; initialization status: -95
ath9k_htc: Failed to initialize the device
This helps when debugging by directly showing the first point of
failure and it could prevent possible errors if a 0x0f.3 revision
is ever supported.
Signed-off-by: Tim Schumacher <timschumi@gmx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As already noted a comment in ath_tx_complete_aggr(), the hardware will
occasionally send a TX status with the wrong tid number. If we trust the
value, airtime usage will be reported to the wrong AC, which can cause the
deficit on that AC to become very low, blocking subsequent attempts to
transmit.
To fix this, account airtime usage to the TID number from the original skb,
instead of the one in the hardware TX status report.
Reported-by: Miguel Catalan Cid <miguel.catalan@i2cat.net>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently there is no way for the driver to signal to mac80211 that it should
schedule a TXQ even if there are no packets on the mac80211 part of that queue.
This is problematic if the driver has an internal retry queue to deal with
software A-MPDU retry.
This patch changes the behavior of ieee80211_schedule_txq to always schedule
the queue, as its only user (ath9k) seems to expect such behavior already:
it calls this function on tx status and on powersave wakeup whenever its
internal retry queue is not empty.
Also add an extra argument to ieee80211_return_txq to get the same behavior.
This fixes an issue on ath9k where tx queues with packets to retry (and no
new packets in mac80211) would not get serviced.
Fixes: 89cea7493a ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath9k/recv.c: In function 'ath_rx_count_airtime':
drivers/net/wireless/ath/ath9k/recv.c:1010:18: warning:
variable 'acq' set but not used [-Wunused-but-set-variable]
It's not used after 89cea7493a ("ath9k: Switch to mac80211 TXQ scheduling
and airtime APIs"). Also remove related variables.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since ath9k reports airtime usage directly using the
ieee80211_report_airtime() callback, it shouldn't also report it using the
tx_time in status. Make sure the field is zeroed before TX status is
reported to avoid spurious airtime being accounted by bits being left over
from earlier uses of the cb.
Fixes: 89cea7493a ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This moves the ath9k driver to use the mac80211 TXQ scheduling and
airtime accounting APIs, removing the corresponding state tracking
inside the driver.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
[rmanohar@codeaurora.org: fixed checkpatch error and warnings]
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
as you are already in a tasklet, it is unnecessary to call
spin_lock_bh, because softirq already disable BH.
Signed-off-by: Zhiwei Jiang <qq282012236@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, they can now return error values if
something went wrong. If that happens, return a NULL as a *dentry to
the relay core instead of passing it an illegal pointer.
The relay core should be able to handle an illegal pointer, but add this
check to be safe.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change snprintf to scnprintf. There are generally two cases where using
snprintf causes problems.
1) Uses of size += snprintf(buf, SIZE - size, fmt, ...) In this case,
if snprintf would have written more characters than what the buffer
size (SIZE) is, then size will end up larger than SIZE. In later uses
of snprintf, SIZE - size will result in a negative number, leading to
problems. Note that size might already be too large by using size =
snprintf before the code reaches a case of size += snprintf.
2) If size is ultimately used as a length parameter for a copy back to
user space, then it will potentially allow for a buffer overflow and
information disclosure when size is greater than SIZE. When the size is
used to index the buffer directly, we can have memory corruption. This
also means when size = snprintf... is used, it may also cause problems
since size may become large. Copying to userspace is mitigated by the
HARDENED_USERCOPY kernel configuration.
The solution to these issues is to use scnprintf which returns the number
of characters actually written to the buffer, so the size variable will
never exceed SIZE.
Cc: Willy Tarreau <w@1wt.eu>
Cc: Silvio Cesare <silvio.cesare@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath9k_of_init() function[0] was initially written on the assumption that
if someone had an explicit ath9k OF node that "there must be something
wrong, why would someone add an OF node if everything is fine"[1]
(Quoting Martin Blumenstingl <martin.blumenstingl@googlemail.com>)
"it turns out it's not that simple. with your requirements I'm now aware
of two use-cases where the current code in ath9k_of_init() doesn't work
without modifications"[1]
The "your requirements" Martin speaks of is the result of the fact that I
have a device (PowerCloud Systems CR5000) has some kind of default - not
unique mac address - set and requires to set the correct MAC address via
mac-address devicetree property, however:
"some cards come with a physical EEPROM chip [or OTP] so "qca,no-eeprom"
should not be set (your use-case). in this case AH_USE_EEPROM should be
set (which is the default when there is no OF node)"[1]
The other use case is:
the firmware on some PowerMac G5 seems to add a OF node for the ath9k
card automatically. depending on the EEPROM on the card AH_NO_EEP_SWAP
should be unset (which is the default when there is no OF node). see [3]
After this patch to ath9k_of_init() the new behavior will be:
if there's no OF node then everything is the same as before
if there's an empty OF node then ath9k will use the hardware EEPROM
(before ath9k would fail to initialize because no EEPROM data was
provided by userspace)
if there's an OF node with only a MAC address then ath9k will use
the MAC address and the hardware EEPROM (see the case above)
with "qca,no-eeprom" EEPROM data from userspace will be requested.
the behavior here will not change
[1]
Martin provides additional background on EEPROM swapping[1].
Thanks to Christian Lamparter <chunkeey@gmail.com> for all his help on
troubleshooting this issue and the basis for this patch.
[0]https://elixir.bootlin.com/linux/v4.20-rc7/source/drivers/net/wireless/ath/ath9k/init.c#L615
[1]https://github.com/openwrt/openwrt/pull/1645#issuecomment-448027058
[2]https://github.com/openwrt/openwrt/pull/1613
[3]https://patchwork.kernel.org/patch/10241731/
Fixes: 138b41253d ("ath9k: parse the device configuration from an OF node")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 4.21. Most notable here is support for
Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide
nvram files for brcmfmac.
Major changes:
brcmfmac
* add support for first trying to get a board specific nvram file
* add support for getting nvram contents from EFI variables
qtnfmac
* use single PCIe driver for all platforms and rename
Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE
* add support for QSR1000/QSR2000 (Topaz) family of chipsets
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
iwlwifi
* PCI IDs for some new 9000-series cards
* improve antenna usage on connection problems
* new firmware debugging infrastructure
* some more work on 802.11ax
* improve support for multiple RF modules with 22000 devices
cordic
* move cordic macros and defines to a public header file
* convert brcmsmac and b43 to fully use cordic library
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcATmGAAoJEG4XJFUm622bk9kH/1RWa2z7Gmjr2wBSLHryvRAH
3FAUSJ4GJPH6MJ5X824srkcVsx2Y1RVt2i+bLXRXLq35aZkrFswohTXVM2h5dU7T
Uy2SL+q9pBUcS7fyv9bE7XV7KsFBJly/5p/wciVRZMnEK6X/w6KkBx/vGvlm5I/C
q196KazbVAYcl6s7KMrfFOYt0Wsto/gdEeesSVBkmcCTEkiKUjjJ4WEDVvAKK+qB
AiwgSdioqYmmEiUuredm6bhVqZG3K2mScoCy95N3jXkiDaKkaYgVtBuAU4Cdju/t
WgLIc9EnUYxXZtwnt889X62P1OkDOtKlj/mjdsGyF0Vrs1W+kErDO0NocOvu2Tk=
=9bL7
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-11-30' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
First set of patches for 4.21. Most notable here is support for
Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide
nvram files for brcmfmac.
Major changes:
brcmfmac
* add support for first trying to get a board specific nvram file
* add support for getting nvram contents from EFI variables
qtnfmac
* use single PCIe driver for all platforms and rename
Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE
* add support for QSR1000/QSR2000 (Topaz) family of chipsets
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
iwlwifi
* PCI IDs for some new 9000-series cards
* improve antenna usage on connection problems
* new firmware debugging infrastructure
* some more work on 802.11ax
* improve support for multiple RF modules with 22000 devices
cordic
* move cordic macros and defines to a public header file
* convert brcmsmac and b43 to fully use cordic library
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We tried to revert commit d9c52fd17c ("ath9k: fix tx99 with monitor
mode interface") but accidentally missed part of the locking change.
The lock has to be held earlier so that we're holding it when we do
"sc->tx99_vif = vif;" and also there in the current code there is a
stray unlock before we have taken the lock.
Fixes: 6df0580be8 ("ath9k: add back support for using active monitor interfaces for tx99")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove experimental tag from dynack Kconfig entry since it has
been tested on outdoor 25Km links
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to make propagation time estimation faster,
use current sample as ewma output value during 'late ack'
tracking
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Check da->enabled flag first in ath_dynack_sample_tx_ts and
ath_dynack_sample_ack_ts routines in order to avoid useless
processing
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move debug log in ath_dynack_sample_tx_ts and ath_dynack_sample_ack_ts
after timestamp buffer head/tail increments in order to make debugging
more user friendly
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to properly support dynack in ad-hoc mode running
wpa_supplicant, take into account authentication frames for
'late ack' detection. This patch has been tested on devices
mounted on offshore high-voltage stations connected through
~24Km link
Reported-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
new_flags is not used after setting its value. It is safe to remove
the unused variable.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1056532 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1056532 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1056532 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A couple of macros that deal with statistics in ath9k rely on the
declaration of the 'sc' variable, which they dereference.
However, when the statistics are disabled, the new instance in
ath_cmn_process_fft() causes a warning for an unused variable:
drivers/net/wireless/ath/ath9k/common-spectral.c: In function 'ath_cmn_process_fft':
drivers/net/wireless/ath/ath9k/common-spectral.c:474:20: error: unused variable 'sc' [-Werror=unused-variable]
It's better if those macros only operate on their arguments instead of
known variable names, and adding a cast to (void) kills off that warning.
Fixes: 03224678c0 ("ath9k: add counters for good and errorneous FFT/spectral frames")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Various documented examples on how to set up tx99 with ath9k rely
on setting up a regular monitor interface for setting the channel.
My previous patch "ath9k: fix tx99 with monitor mode interface" made
it possible to set it up this way again. However, it was removing support
for using an active monitor interface, which is required for controlling
the bitrate as well, since the bitrate is not passed down with a regular
monitor interface.
This patch partially reverts the previous one, but keeps support for using
a regular monitor interface to keep documented steps working in cases
where the bitrate does not matter
Fixes: d9c52fd17c ("ath9k: fix tx99 with monitor mode interface")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since the debug print code is outside of the loop, it shouldn't use the loop
iterator anymore but instead print the found maximum index.
Cc: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FFT max index retrieval was not retrieved correctly for HT20/HT40 FFT
frames. Fixing the retrieval allows us to remove the fixup function as
well. While at it, split the spectral_max_index function into versions
for ht20 and ht40 to simplify the code.
Cc: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With the loop break like this, there are false "FFT report truncated"
messages because the iterator is not advanced as the check expects.
Instead, just return, for a single frame there is nothing left to be
done anyways.
Cc: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is helpful to see whether spectral samples get discarded.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
'fops_dump_nfcal' is not used since commit 4447d815fd ("ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
