Extended the bit mask value of the HTT stats to get the Mu-MIMO
related stats via tracing.
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Invalid rate code is sent to firmware when multicast rate value of 0 is
sent to driver indicating disabled case, causing broken mesh path.
so fix that.
Tested on QCA9984 with firmware 10.4-3.6.1-00827
Sven tested on IPQ4019 with 10.4-3.5.3-00057 and QCA9888 with 10.4-3.5.3-00053
(ath10k-firmware) and 10.4-3.6-00140 (linux-firmware 2018-12-16-211de167).
Fixes: cd93b83ad9 ("ath10k: support for multicast rate control")
Co-developed-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Tested-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After implementing PN replay check we can enable SDIO support on QCA6174.
Tested with client mode on all security modes, and fragmentation as well. AP
mode does not work yet.
Also tone down the warning about SDIO being not ready yet.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1. AP mode
is not working yet.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On high latency devices (SDIO, USB) ath10k did not handle fragmented frames and
all fragmented frames on receive path were lost in ath10k. Even a simple ping
test failed with fragmentation.
The fragmented packets are decapsulated based on the security mode, then the PN
is checked and the fragmented frame is passed to mac80211. mac80211 in
ieee80211_rx_h_defragment() will then combine the fragment frames and forward
to upper layers.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On high latency devices (SDIO, USB) ath10k did not do PN replay check, a data
frame with an invalid PN number was not discard as it should have been. So this
patch implements PN replay in ath10k. PN replay check for fragmented frames is
implemented in followup patch.
With low latency devices (PCI, AHB) hardware can store the data
frames's content to host memory directly and the firmware can fully reorder
data frames, and do PN replay check at the same time. But for high latency
devices all data frames will be received and stored in firmware's memory and it
is hard to do full reorder because of the memory size limitations in the
firmware. This is why the PN replay protections needs to be implemented in host
driver.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the handler for HTT_T2H_MSG_TYPE_SEC_IND event from firmware, which stores
PN for replay check implemented in the following patch.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the struct for PN replay protection and fragment packet
handler.
Also fix the bitmask of HTT_RX_DESC_HL_INFO_MCAST_BCAST to match what's currently
used by SDIO firmware. The defines are not used yet so it's safe to modify
them. Remove the conflicting HTT_RX_DESC_HL_INFO_FRAGMENT as
it's not either used in ath10k.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_mac_vif_chan() always returns an error for the given vif
during system-wide resume which reliably triggers two WARN_ON()s
in ath10k_bss_info_changed() and they are not particularly
useful in that code path, so drop them.
Tested: QCA6174 hw3.2 PCI with WLAN.RM.2.0-00180-QCARMSWPZ-1
Tested: QCA6174 hw3.2 SDIO with WLAN.RMH.4.4.1-00007-QCARMSWP-1
Fixes: cd93b83ad9 ("ath10k: support for multicast rate control")
Fixes: f279294e9e ("ath10k: add support for configuring management packet rate")
Cc: stable@vger.kernel.org
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 25733c4e67 ("ath10k: pci: use mutex for diagnostic window CE
polling") introduced a regression where we try to sleep (grab a mutex)
in an atomic context:
[ 233.602619] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:254
[ 233.602626] in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper/0
[ 233.602636] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 5.1.0-rc2 #4
[ 233.602642] Hardware name: Google Scarlet (DT)
[ 233.602647] Call trace:
[ 233.602663] dump_backtrace+0x0/0x11c
[ 233.602672] show_stack+0x20/0x28
[ 233.602681] dump_stack+0x98/0xbc
[ 233.602690] ___might_sleep+0x154/0x16c
[ 233.602696] __might_sleep+0x78/0x88
[ 233.602704] mutex_lock+0x2c/0x5c
[ 233.602717] ath10k_pci_diag_read_mem+0x68/0x21c [ath10k_pci]
[ 233.602725] ath10k_pci_diag_read32+0x48/0x74 [ath10k_pci]
[ 233.602733] ath10k_pci_dump_registers+0x5c/0x16c [ath10k_pci]
[ 233.602741] ath10k_pci_fw_crashed_dump+0xb8/0x548 [ath10k_pci]
[ 233.602749] ath10k_pci_napi_poll+0x60/0x128 [ath10k_pci]
[ 233.602757] net_rx_action+0x140/0x388
[ 233.602766] __do_softirq+0x1b0/0x35c
[...]
ath10k_pci_fw_crashed_dump() is called from NAPI contexts, and firmware
memory dumps are retrieved using the diag memory interface.
A simple reproduction case is to run this on QCA6174A /
WLAN.RM.4.4.1-00132-QCARMSWP-1, which happens to be a way to b0rk the
firmware:
dd if=/sys/kernel/debug/ieee80211/phy0/ath10k/mem_value bs=4K count=1
of=/dev/null
(NB: simulated firmware crashes, via debugfs, don't trigger firmware
dumps.)
The fix is to move the crash-dump into a workqueue context, and avoid
relying on 'data_lock' for most mutual exclusion. We only keep using it
here for protecting 'fw_crash_counter', while the rest of the coredump
buffers are protected by a new 'dump_mutex'.
I've tested the above with simulated firmware crashes (debugfs 'reset'
file), real firmware crashes (the 'dd' command above), and a variety of
reboot and suspend/resume configurations on QCA6174A.
Reported here:
http://lkml.kernel.org/linux-wireless/20190325202706.GA68720@google.com
Fixes: 25733c4e67 ("ath10k: pci: use mutex for diagnostic window CE polling")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We currently have two levels of strict validation:
1) liberal (default)
- undefined (type >= max) & NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
- garbage at end of message accepted
2) strict (opt-in)
- NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
Split out parsing strictness into four different options:
* TRAILING - check that there's no trailing data after parsing
attributes (in message or nested)
* MAXTYPE - reject attrs > max known type
* UNSPEC - reject attributes with NLA_UNSPEC policy entries
* STRICT_ATTRS - strictly validate attribute size
The default for future things should be *everything*.
The current *_strict() is a combination of TRAILING and MAXTYPE,
and is renamed to _deprecated_strict().
The current regular parsing has none of this, and is renamed to
*_parse_deprecated().
Additionally it allows us to selectively set one of the new flags
even on old policies. Notably, the UNSPEC flag could be useful in
this case, since it can be arranged (by filling in the policy) to
not be an incompatible userspace ABI change, but would then going
forward prevent forgetting attribute entries. Similar can apply
to the POLICY flag.
We end up with the following renames:
* nla_parse -> nla_parse_deprecated
* nla_parse_strict -> nla_parse_deprecated_strict
* nlmsg_parse -> nlmsg_parse_deprecated
* nlmsg_parse_strict -> nlmsg_parse_deprecated_strict
* nla_parse_nested -> nla_parse_nested_deprecated
* nla_validate_nested -> nla_validate_nested_deprecated
Using spatch, of course:
@@
expression TB, MAX, HEAD, LEN, POL, EXT;
@@
-nla_parse(TB, MAX, HEAD, LEN, POL, EXT)
+nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression TB, MAX, NLA, POL, EXT;
@@
-nla_parse_nested(TB, MAX, NLA, POL, EXT)
+nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT)
@@
expression START, MAX, POL, EXT;
@@
-nla_validate_nested(START, MAX, POL, EXT)
+nla_validate_nested_deprecated(START, MAX, POL, EXT)
@@
expression NLH, HDRLEN, MAX, POL, EXT;
@@
-nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT)
+nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT)
For this patch, don't actually add the strict, non-renamed versions
yet so that it breaks compile if I get it wrong.
Also, while at it, make nla_validate and nla_parse go down to a
common __nla_validate_parse() function to avoid code duplication.
Ultimately, this allows us to have very strict validation for every
new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the
next patch, while existing things will continue to work as is.
In effect then, this adds fully strict validation for any new command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although not likely, the bundle allocation might fail.
Add proper error check and warning print.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HTC header carries junk values that may be interpreted by the firmware
differently. Enable credit update only if flow control is enabled for
the corresponding endpoint.
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With SDIO there's a use after free after a data frame is transfered, call stack
below. This happens because ath10k_htt_tx_hl() directly transmits the skb
provided by mac80211 using ath10k_htc_send(), all other HTT functions use
separate skb created with ath10k_htc_alloc_skb() to transmit the HTC packet.
After the packet is transmitted mac80211 frees the skb in ieee80211_tx_status()
but HTT layer expects that it still owns the skb, and frees it in
ath10k_htt_htc_tx_complete().
To fix this take a reference of skb before sending it to HTC layer to make sure
we still own the skb.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
ath10k_htt_tx_hl() is only used by SDIO and USB so other busses (PCI, AHB and
SNOC) should be unaffected.
call stack of use-after-free:
dump_backtrace+0x0/0x2d8
show_stack+0x20/0x2c
__dump_stack+0x20/0x28
dump_stack+0xc8/0xec
print_address_description+0x74/0x240
kasan_report+0x258/0x274
__asan_report_load4_noabort+0x20/0x28
skb_pull+0xbc/0x114
ath10k_htc_notify_tx_completion+0x190/0x2a4 [ath10k_core]
ath10k_sdio_write_async_work+0x1e4/0x2c4 [ath10k_sdio]
process_one_work+0x3d8/0x8b0
worker_thread+0x518/0x7e0
kthread+0x260/0x278
ret_from_fork+0x10/0x18
Allocated by one task:
kasan_kmalloc+0xa0/0x13c
kasan_slab_alloc+0x14/0x1c
kmem_cache_alloc+0x144/0x208
__alloc_skb+0xec/0x394
alloc_skb_with_frags+0x8c/0x374
sock_alloc_send_pskb+0x520/0x5d4
sock_alloc_send_skb+0x40/0x50
__ip_append_data+0xf5c/0x1858
ip_make_skb+0x194/0x1d4
udp_sendmsg+0xf24/0x1ab8
inet_sendmsg+0x1b0/0x2e0
sock_sendmsg+0x88/0xa0
__sys_sendto+0x220/0x3a8
__arm64_sys_sendto+0x78/0x80
el0_svc_common+0x120/0x1e0
el0_svc_compat_handler+0x64/0x80
el0_svc_compat+0x8/0x18
Freed by another task:
__kasan_slab_free+0x120/0x1d4
kasan_slab_free+0x10/0x1c
kmem_cache_free+0x74/0x504
kfree_skbmem+0x88/0xc8
__kfree_skb+0x24/0x2c
consume_skb+0x114/0x18c
__ieee80211_tx_status+0xb7c/0xf60 [mac80211]
ieee80211_tx_status+0x224/0x270 [mac80211]
ath10k_txrx_tx_unref+0x564/0x950 [ath10k_core]
ath10k_htt_t2h_msg_handler+0x178c/0x2a38 [ath10k_core]
ath10k_htt_htc_t2h_msg_handler+0x20/0x30 [ath10k_core]
ath10k_sdio_irq_handler+0xcc0/0x1654 [ath10k_sdio]
process_sdio_pending_irqs+0xec/0x358
sdio_run_irqs+0x68/0xe4
sdio_irq_work+0x1c/0x28
process_one_work+0x3d8/0x8b0
worker_thread+0x518/0x7e0
kthread+0x260/0x278
ret_from_fork+0x10/0x18
Reported-by: Wen Gong <wgong@codeaurora.org>
Tested-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Transmit completion for SDIO is similar to PCIe, modify the high
latency path to allow SDIO modules to use the msdu id.
kvalo: the original patch from Alagu enabled this only for SDIO but I'm not
sure should we also enable this with USB. I'll use bus params to enable this
for so that it's easy to enable also for USB later.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This way we don't need to set every variable and give them to default, which is
zero. This is also safer in case we forgot to initalise a new field in some of
the bus modules.
Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HTT High Latency (ATH10K_DEV_TYPE_HL) does not use txdone_fifo at all, we don't
even initialise it by skipping ath10k_htt_tx_alloc_buf() in
ath10k_htt_tx_start(). Because of this using QCA6174 SDIO
ath10k_htt_rx_tx_compl_ind() will crash when it accesses unitialised
txdone_fifo. So skip txdone_fifo when using High Latency mode.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Disabling interrupts this early meant WMI communication was not working anymore
when the SDIO device was removed. But we call ath10k_core_unregister() that
will eventually call ath10k_sdio_hif_stop(), which disables the interrupts. So
there's actually no need to disable interrupts here.
Also remove cancel_work_sync() as it's also called in ath10k_sdio_hif_stop().
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On QCA6174 SDIO devices the SDIO interrupt will fail if UART is
disabled from ath10k. SDIO firmware enables UART printouts by
default. If ath10k will try to enable UART again the firmware
will configure it's GPIO line incorrectly and SDIO interrupts
won't work anymore. The workaround is to set UART pin again (19
for QCA6174 SDIO) if uart_print is 0.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently there is no way for the driver to signal to mac80211 that it should
schedule a TXQ even if there are no packets on the mac80211 part of that queue.
This is problematic if the driver has an internal retry queue to deal with
software A-MPDU retry.
This patch changes the behavior of ieee80211_schedule_txq to always schedule
the queue, as its only user (ath9k) seems to expect such behavior already:
it calls this function on tx status and on powersave wakeup whenever its
internal retry queue is not empty.
Also add an extra argument to ieee80211_return_txq to get the same behavior.
This fixes an issue on ath9k where tx queues with packets to retry (and no
new packets in mac80211) would not get serviced.
Fixes: 89cea7493a ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, rx_duration for each peer is not getting populated in
fw_stats debugfs entry for WCN3990.
WCN3990 firmware sends rx duration for each peer as part of
peer_extd_stats in WMI_UPDATE_STATS_EVENT. To enable peer_extd_stats,
firmware expects host to send fw_stats_req_mask with flag
WMI_TLV_PEER_STATS_EXTD set in WMI_REQUEST_STATS_CMD.
Send fw_stats_req_mask with flag WMI_TLV_PEER_STATS_EXTD set in
WMI_REQUEST_STATS_CMD and parse the peer_extd_stats in
WMI_UPDATE_STATS_EVENT to populate the rx_duration of each peer
in fw_stats debugfs entry.
Currently the driver handles 32-bit rx_duration, but the rx_duration
for WCN3990 can be upto 63 bit. The firmware sends rx_duration split
into two 32-bit fields, with the upper 32-bits being valid only if its
MSB is set. This change handles the 63-bit rx_duration obtained from
WCN3990 and maintain the backward compatibility.
To get the rx_duration of each connected peer :
cat /sys/kernel/debug/ieee80211/phyX/ath10k/fw_stats
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ht_idx (ht rate index) and idx (rate table index) are calculated based on
mcs index. This mcs index used in the above calculation should be 0-9 for
getting the correct ht_idx and idx.
Currently the mcs index used for the above calculations is mcs index which
can be 0-31 (in case of HT), leading to incorrect rate index and ht index values.
Fix the issue by obtaining mcs value from the ratecode reported by firmware
and use it for calculating ht_idx and idx (rate-table index).
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: e88975ca37 ("ath10k: dump tx stats in rate table format")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SGI is updated wrongly in tx stats table in debugfs per sta
entry. To know whether the packets/bytes are sent with SHORT GI,
test whether the SGI bit(ATH10K_RATE_INFO_FLAGS_SGI_BIT) is set or
not in the txrate flags.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc8 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, the bandwidth is updated wrongly in BW table in tx_stats
debugfs per sta as there is difference in number of bandwidth type
in mac80211 and driver stats table. This leads to bandwidth getting
updated at wrong index in bandwidth table in tx_stats.
Fix this index mismatch between mac80211 and driver stats table (BW table)
by making the number of bandwidth type in driver compatible with mac80211.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc8 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The NSS data is updated incorrectly in the tx stats as the array
indexing starts from zero.
Fix the incorrect updation of NSS data in tx_stats by taking into
consideration the array index starting from zero.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc8 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 firmware versions WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1 & onwards
supports maximum 33 peers including self peer. To support maximum peers,
send updated peer param to firmware during initialization.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The calibration data fetch will trigger sdio error, then sdio will
become fail untill reboot system.
If happens when run ifconfig wlan down, then ifconfig wlan up will
fail untill reboot system.Remove it fix the ifconfig wlan issue.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The length of wmi tlv command for management tx send is calculated
incorrectly in case of protected management frames as there is addition
of IEEE80211_CCMP_MIC_LEN twice. This leads to improper behaviour of
firmware as the wmi tlv mgmt tx send command for protected mgmt frames
is formed wrongly.
Fix the length calculation of wmi tlv command for mgmt tx send in case
of protected management frames by adding the IEEE80211_CCMP_MIC_LEN only
once.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: 1807da4973 "ath10k: wmi: add management tx by reference support over wmi"
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SDIO firmware does not provide RSSI value to the host, it's only set to
zero. In that case don't report the value to mac80211. One risk here is that
value zero might be a valid value with other firmware, currently there's no way
to detect that.
Without the fix, the rssi value indicated by iw changes between the actual
value and -95.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The target device needs to be reset during power_down(), otherwise only the
first power_up() will work. And as ath10k calls power_up() during driver
initialisation the driver would be otherwise unusable.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SDIO firmware may turn it on based on scratch registers so disable the
firmware log to avoid that.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SDIO firmware does not allow transmitting packets with the
reduced tx completion HI_ACS option. SDIO firmware uses 1544 as
alternate credit size, which is not big enough for the maximum sized
mac80211 frames. Disable both these HI_ACS flags for SDIO.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is a theoretical fix, the issue is found in code review.
When adding the host memory chunks into wmi-tlv init command,
there is no separate tlv header for each host memory chunk
in the struct array, which breaches the convention between
host and firmware, will result in mismatch between the two.
To fix this issue, add separate tlv headers for the host
memory chunks in wmi-tlv init command.
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently after enabling the WMI debug logging,
there is no detail printed about the param id
and the param value for the pdev, vdev and
peer params which are set.
Enhance the WMI logging to print the param id
and the param value for pdev, vdev and peer set
param wmi commands.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In WCN3990, WMI_TLV_SERVICE_TX_DATA_MGMT_ACK_RSSI service Indicates that
the firmware has the capability to send the RSSI value of the ACK for all
data and management packets transmitted.
If WMI_RSRC_CFG_FLAG_TX_ACK_RSSI is set in host capability then firmware
sends RSSI value in "data" tx completion event. Host extracts ack rssi
values of data packets from their tx completion event.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In WCN3990, WMI_TLV_SERVICE_TX_DATA_MGMT_ACK_RSSI service Indicates that
the firmware has the capability to send the RSSI value of the ACK for all
data and management packets transmitted.
If WMI_RSRC_CFG_FLAG_TX_ACK_RSSI is set in host capability then firmware
sends RSSI value in "management" tx completion event. Host extracts ack
rssi values of management packets from their tx completion event.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the driver receives the tx completion of the
descriptor over ce, it clears the nbytes configured
for that particular descriptor. WCN3990 uses ce
descriptors with 64-bit address.
Currently during handling the tx completion of the
descriptors, the nbytes are accessed from the descriptors
using ce_desc for 32-bit targets. This will lead to clearing
of memory at incorrect offset if DMA MASK is set to greater
than 32 bits.
Attach different ce tx copy completed handler for targets
using address above 32-bit address.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use SPDX identifiers everywhere in ath10k.
Makefile was incorrectly marked in commit b24413180f ("License cleanup: add
SPDX GPL-2.0 license identifier to files with no license"), fix that as well.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of copying fields one by one copy the whole structure. This way there's
no need to modify the function every time we add a new field to the struct.
Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With W=1 there's a warning:
drivers/net/wireless/ath/ath10k/wow.c:93: warning: Function parameter or member 'new' not described in 'ath10k_wow_convert_8023_to_80211'
drivers/net/wireless/ath/ath10k/wow.c:93: warning: Function parameter or member 'old' not described in 'ath10k_wow_convert_8023_to_80211'
Fix it by changing the documentation marker '/**' to a normal code comment.
While at it, clean up the line wrapping.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With W=1 GCC warns:
drivers/net/wireless/ath/ath10k/htt.h:1746:1: warning: alignment 1 of 'struct ath10k_htt_txbuf_32' is less than 4 [-Wpacked-not-aligned]
drivers/net/wireless/ath/ath10k/htt.h:1753:1: warning: alignment 1 of 'struct ath10k_htt_txbuf_64' is less than 4 [-Wpacked-not-aligned]
Fix that by using __align(4). Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When adding a new value to enum wmi_service it's very easy to miss that the new
value should be also added to wmi_service_name() mapping function. Modify the
function so that GCC can now warn about this:
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_FOO' not handled in switch [-Wswitch]
And also add a reminder to the enum.
Thanks to Jouni Malinen for the idea.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After implementing the next patch GCC reported:
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_BTCOEX' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_MGMT_TX_WMI' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_SPOOF_MAC_SUPPORT' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_VDEV_DISABLE_4_ADDR_SRC_LRN_SUPPORT' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_THERM_THROT' not handled in switch [-Wswitch]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If supported, update transmit airtime in mac80211 with the airtime
values reported by the firmware. TX airtime of the PPDU is reported
via HTT data TX completion indication message.
A new service flag 'WMI_SERVICE_REPORT_AIRTIME' is added to advertise
the firmware support. For firmwares which do not support this feature,
TX airtime is calculated in the driver using TX bitrate.
Hardwares tested : QCA9984
Firmwares tested : 10.4-3.6.1-00841
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Multicast/broadcast traffic destined for a particular vlan group will
always be encrypted in software. To enable dynamic VLANs, it requires
driver support for sending software encrypted packets.
In ath10k, sending software encrypted frames is allowed only when we insmod
the driver with cryptmode param set to 1, this configuration disables
hardware crypto and enables RAW mode implicitly. Since, enabling raw
mode has performance impact, this cannot be considered as an ideal
solution for supporting VLANs in the driver.
As an alternative take, in this approach, cryptographic keys for
unicast traffic (per peer PTKs) and keys for non-vlan group traffic
will be configured in hardware, allowing hardware encryption for unicast
and non-vlan group traffic. Only vlan group traffic will be encrypted in
software and pushed to the target with encap mode set to RAW in the TX
descriptors.
Not all firmwares can support this type of key configuration(having few
keys installed in hardware and few only in software); for this purpose a
new WMI service flag "WMI_SERVICE_PER_PACKET_SW_ENCRYPT" is introduced to
advertise this support.
Also, adding the logic required to send sw encrypted frames in raw mode.
Hardwares Tested : QCA9984, QCA988X
Firmwares Tested : 10.4-3.5.3-00057, 10.2.4-1.0-00042
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Configure fine timing measurement (FTM) responder role from the
ftm_responder bss param sent by mac80211. With FTM functionality offloaded
to firmware, adding the interface allows userspace to enable or disable
FTM responder functionality. ath10k disables it at the time of interface
creation.
Supported FW: 10.4
Tested on IPQ4019 with firmware: 10.4-3.2.1.1-00022
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The airtime of a transmitted frame will be estimated from last used tx rate
which the firmware reports with the peer stats feature
(WMI_SERVICE_PEER_STATS). The airtime is computed on the tx path and it
will be reported to mac80211 upon tx completion.
This change is based on Kan's orginal commit in Chromium tree
("CHROMIUM: ath10k: Implementing airtime fairness based TX scheduler")
ref: https://chromium-review.googlesource.com/588190
Tested on QCA4019 with firmware version 10.4-3.2.1.1-00015
Tested on QCA9984 with firmware version 10.4-3.9.0.1-00005
Signed-off-by: Kan Yan <kyan@google.com>
[rmanohar@codeaurora.org: ported only the airtime computation]
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
[toke@redhat.com: Rebase to mac80211-next, add test note]
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k maintains common txqs list for all stations. This txq
management can be removed by migrating to mac80211 txq APIs
and let mac80211 handle txqs reordering based on reported airtime.
By doing this, txq fairness maintained in ath10k i.e processing
N frames per txq is removed. By adapting to mac80211 APIs,
ath10k will support mac80211 based airtime fairness algorithm.
Tested on QCA4019 with firmware version 10.4-3.2.1.1-00015
Tested on QCA9984 with firmware version 10.4-3.9.0.1-00005
Tested-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Co-developed-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 750afb08ca ("cross-tree: phase out dma_zalloc_coherent()") introduced
a new checkpatch warning:
drivers/net/wireless/ath/ath10k/ce.c:1602: line over 90 characters
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 supports shadow registers write operation support
for copy engine for regular operation in powersave mode.
Since WCN3990 is a 64-bit target, the shadow register
implementation needs to be done in the copy engine handlers
for 64-bit target. Currently the shadow register implementation
is present in the 32-bit target handlers of copy engine.
Fix the shadow register copy engine write operation
implementation for 64-bit target(WCN3990).
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes: b7ba83f7c4 ("ath10k: add support for shadow register for WNC3990")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The support to put WCN3990 firmware into Factory
test mode is not present currently. The WCN3990
firmware can operate in Factory test mode based
on the mode it receives in the wlan enable message
from the host driver.
When the host driver is started in testmode send
the operating mode as UTF mode, to the WCN3990
firmware, in the wlan enable message to start the
firmware in Factory test mode.
Tested on: WCN3990
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The DIAG copy engine is only used via polling, but it holds a spinlock
with softirqs disabled. Each iteration of our read/write loops can
theoretically take 20ms (two 10ms timeout loops), and this loop can be
run an unbounded number of times while holding the spinlock -- dependent
on the request size given by the caller.
As of commit 39501ea641 ("ath10k: download firmware via diag Copy
Engine for QCA6174 and QCA9377."), we transfer large chunks of firmware
memory using this mechanism. With large enough firmware segments, this
becomes an exceedingly long period for disabling soft IRQs. For example,
with a 500KiB firmware segment, in testing QCA6174A, I see 200 loop
iterations of about 50-100us each, which can total about 10-20ms.
In reality, we don't really need to block softirqs for this duration.
The DIAG CE is only used in polling mode, and we only need to hold
ce_lock to make sure any CE bookkeeping is done without screwing up
another CE. Otherwise, we only need to ensure exclusion between
ath10k_pci_diag_{read,write}_mem() contexts.
This patch moves to use fine-grained locking for the shared ce_lock,
while adding a new mutex just to ensure mutual exclusion of diag
read/write operations.
Tested on QCA6174A, firmware version WLAN.RM.4.4.1-00132-QCARMSWPZ-1.
Fixes: 39501ea641 ("ath10k: download firmware via diag Copy Engine for QCA6174 and QCA9377.")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW credit flow control is enabled for only WMI ctrl
service(CE3) but credit update is requested unconditionally
on all HTC services as part of HTC tx in CE3/CE0/CE4.
This is causing WOW failure as FW is not expecting credit
report request on other end-points(CE0/CE4).
Request credit report only on those endpoints where
credit flow control is enabled.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wow pause iface config controls the PCI D0/D3-WOW cases for pcie
bus state. Firmware does not expects WOW_IFACE_PAUSE_ENABLED config
for bus/link that cannot be suspended ex:snoc and does not trigger
common subsystem shutdown.
Disable interface pause wow config for integrated chipset(WCN3990)
for correct WOW configuration in the firmware.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Register snoc bus layer suspend/resume PM ops and configure
the wakeup source(CE2) for the device.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Many integrated QCA9984 WiFis in various IPQ806x platform routers
from various vendors (Netgear R7800, ZyXEL NBG6817, TP-LINK C2600,
etc.) have either blank, bogus or non-unique MAC-addresses in
their calibration data.
As a result, OpenWrt utilizes a discouraged binary calibration data
patching method that allows to modify the device's MAC-addresses right
at the source. This is because the ath10k' firmware extracts the MAC
address from the supplied radio/calibration data and issues a response
to the ath10k linux driver. Which was designed to take the main MAC in
ath10k_wmi_event_ready().
Part of the "setting an alternate MAC" issue was already tackled by a
patch from Brian Norris:
commit 9d5804662c
("ath10k: retrieve MAC address from system firmware if provided")
by allowing the option to specify an alternate MAC-address with the
established device_get_mac_address() function which extracts the right
address from DeviceTree/fwnode mac-address or local-mac-address
properties and saves it for later.
However, Ben Greear noted that the Qualcomm's ath10k firmware is liable
to not properly calculate its rx-bssid mask in this case. This can cause
issues in the popluar "multiple AP with a single ath10k instance"
configurations.
To improve MAC address handling, Felix Fietkau suggested to call
pdev_set_base_macaddr_cmdid before bringing up the first vif and
use the first vif MAC address there. Which is in ath10k_core_start().
This patch implement Felix Fietkau's request to
"call pdev_set_base_macaddr_cmdid before bringing up the first vif".
The pdev_set_base_macaddr_cmdid is already declared for all devices
and version. The driver just needed the support code for this
function.
Tested on:
QCA9880/CUS223, firmwares: 10.2.4.13-2, 10.2.4.70.44, 10.2.4-1.0-00041
QCA9887/MR33 firmware:10.2.4-1.0-00033
QCA4019/RT-AC58U firmware: 10.4-3.4-00104, 10.4-3.5.3-00057
QCA9984/R7800 firmware: Candela Technologies (CT) Firmware
BugLink: https://lists.openwrt.org/pipermail/openwrt-devel/2018-November/014595.html
Fixes: 9d5804662c ("ath10k: retrieve MAC address from system firmware if provided")
Cc: Brian Norris <briannorris@chromium.org>
Cc: Ben Greear <greearb@candelatech.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TLV based firmware ex. QCA6174, WCN3990 expects key cipher value
set to 9 while non-TLV firmware expects key cipher value set to 8
for enabling GCMP and GCMP-256 cipher suites.
To fix this problem, attach the key cipher suite values based on
wmi version.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hostapd uses CCMP, GCMP & GCMP-256 as 'wpa_pairwise' option to run WPA3.
In WCN3990 firmware cipher suite numbers 9 to 11 are for CCMP,
GCMP & GCMP-256.
To enable CCMP, GCMP & GCMP-256 cipher suites in WCN3990 firmware,
host sets 'n_cipher_suites = 11' while initializing hardware parameters.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The series "[PATCH 0/2] mt76x0: initialize per-channel max_power" depends on
commit d04ca38386 ("mt76x0u: fix suspend/resume"), so merge wireless-drivers
into wireless-drivers-next to get that.
ath.git patches for 5.1. Major changes:
ath10k
* change QMI interface to support the new (and backwards incompatible)
interface from HL3.1 and used in recent HL2.0 branch firmware releases
ath
* add new country codes for US
Firmware sends the tx_duration for each in HTT_T2H_MSG_TYPE_PEER_STATS
msg. Fill the tx_duration sent by firmware in the tx stats information
per STA.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware advertises the LDPC support information for HT in
HT capability info in the wmi service ready event. To provide
granularity, firmware now advertises WMI_HT_CAP_RX_LDPC and
WMI_HT_CAP_TX_LDPC separately. To support LDPC, host should
also check for WMI_HT_CAP_RX_LDPC and WMI_HT_CAP_TX_LDPC in HT
capabilities.
Add a condition to existing logic in host to know whether firmware
supports LDPC or not.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reduce the transmit MSDU count for SDIO, to match with the descriptors
as used by the firmware. This also acts as a high watermark level for
transmit. Too many packets to the firmware results in transmit overflow
interrupt.
It only affect SDIO chip, it will not cause functionaly changes to
other hardware.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, they can now return error values if
something went wrong. If that happens, return a NULL as a *dentry to
the relay core instead of passing it an illegal pointer.
The relay core should be able to handle an illegal pointer, but add this
check to be safe.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath10k/snoc.c: In function 'ath10k_snoc_tx_pipe_cleanup':
drivers/net/wireless/ath/ath10k/snoc.c:681:22: warning:
variable 'ar_snoc' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sdio_register_driver() doesn't do this for us, unlike (for example)
platform_driver_register(). This is important for helping track
module-to-device relationships.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The swap box flag of firmware is not set before htc ready, then it
will not set swap box flag in ath10k driver, and it will let swap
box setting not same between firmware and ath10k driver, then it
will trigger firmware assert failure.
Check the flag and set swap box after htc ready will fix the firmware
assert failure.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hw-restart crash inject mode is a special mode, where
there is no crash generated in the firmware, but instead
the driver restarts the firmware. In order to restart WCN3990
firmware, the driver needs to send qmi_wlan_disable message
followed by the qmi_wlan_enable message to the WCN3990 firmware.
Currently the qmi_wlan_disable message is not sent to
the WCN3990 firmware when hw-restart crash is injected,
which causes the firmware to crash when the driver sends
qmi_wlan_enable message during ath10k_restart.
Send qmi_wlan_disable to the WCN3990 firmware when the
hw-restart crash is injected via debugfs.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The management frames transmitted are dma mapped with
direction TO_DEVICE, but incorrectly mapped with
direction FROM_DEVICE during tx complete and error cases.
Fix the direction of dma during dma unmap of the
transmitted management frames.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes: 38a1390e02 ("ath10k: dma unmap mgmt tx buffer if wmi cmd send fails")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 sends tx completion of multiple management
frames bundled together in a single event, if the
host driver exposes the support to handle this
bundled tx completion event. This reduces the number
of WMI events which are sent to the host driver by
the target.
Set the BUNDLE_TX_COMPL flag in the host capability
flags when host sends the wmi init command, to indicate
the host capability to handle bundled tx completion for
management frames.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 supports sending tx completion for multiple
management frames bundled together in a single event.
Add support to handle the bundled tx completion
event for WCN3990.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HOST capability interface data structures are updated
in HL3.1 fw version. Update the qmi host capability
members for compatibility across different firmware
versions.
Since this change breaks backward compatibility with
HL2.0 fw, HL2.0 fw upgrade to WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
or later version is required.
Testing:
Tested on QCS404 platform(WCN3990 HW).
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 5.1. Lots of new features in various drivers
but nothing really special standing out.
Major changes:
brcmfmac
* DMI nvram filename quirk for PoV TAB-P1006W-232 tablet
rsi
* support for hardware scan offload
iwlwifi
* support for Target Wakeup Time (TWT) -- a feature that allows the AP
to specify when individual stations can access the medium
* support for mac80211 AMSDU handling
* some new PCI IDs
* relicense the pcie submodule to dual GPL/BSD
* reworked the TOF/CSI (channel estimation matrix) implementation
* Some product name updates in the human-readable strings
mt76
* energy detect regulatory compliance fixes
* preparation for MT7603 support
* channel switch announcement support
mwifiex
* support for sd8977 chipset
qtnfmac
* support for 4addr mode
* convert to SPDX license identifiers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcWoRZAAoJEG4XJFUm622bOm4H/j2Tt6qS5yz3ioH2I7R+f7e/
8C2JJia+uQs8iChdyCjCFcDymmjB2l5u72JvupwCdERzp3okv/xmJiLW5wFW2z4x
B3Nrd4FV2EMIdsRXg1RWbwZHC4wIY6lFhL1OcUcuNwpb5ab1ppvQFHmH5logd7DC
euFSe02g8xmXdUMciRDKGUdiSiDIApmx9dUfguaqYtepqeW3hmDEEkeDicaf2fjq
cM5qAvssIAgUTqwIImEQQEU7j7A2TgMYkRBNzwv2QG47jy6OlgXkZVByvtq59irg
v4BFNtG6uRWTugxQ/FwYWeqsrnjegFNKm5MFbS6BDxbe05M7QzeK8zm55fE9ZGk=
=cHbd
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-02-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.1
First set of patches for 5.1. Lots of new features in various drivers
but nothing really special standing out.
Major changes:
brcmfmac
* DMI nvram filename quirk for PoV TAB-P1006W-232 tablet
rsi
* support for hardware scan offload
iwlwifi
* support for Target Wakeup Time (TWT) -- a feature that allows the AP
to specify when individual stations can access the medium
* support for mac80211 AMSDU handling
* some new PCI IDs
* relicense the pcie submodule to dual GPL/BSD
* reworked the TOF/CSI (channel estimation matrix) implementation
* Some product name updates in the human-readable strings
mt76
* energy detect regulatory compliance fixes
* preparation for MT7603 support
* channel switch announcement support
mwifiex
* support for sd8977 chipset
qtnfmac
* support for 4addr mode
* convert to SPDX license identifiers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
HTT aggr message parameter in HL2.0 fw are different in comparison
to legacy fw version. Fill correct HTT aggr msg parameter for
targets using HL2.0 firmware.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After system entering S5 (shut down but system still
providing power to QCA9377) on Ubuntu platform, power
consumption of QCA9377 is 69mA, which is too high.
The root cause is pci_soft_reset is not set for QCA9377
during pci probe.
To fix this issue, set 'pci_soft_reset' to 'th10k_pci_warm_reset',
and then the power consumption drops to a normal value(10mA).
Verified on Dell Ubuntu platform with firmware:
WLAN.TF.1.0-00002-QCATFSWPZ-5
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 is a 37-bit target but can address memory range
only upto 35 bits. The 36th bit is used to control the
smmu/iommu translation and the 37th bit is used by the
internal bus masters to access the wifi subsystem internal
SRAM. With the DMA mask set to 37i-bit, the host driver
can get 37-bit dma address, which leads to incorrect
address access in the target.
Hence the host driver can used addresses upto 35-bit
for WCN3990. Fix the dma mask for wcn3990 to 35-bit,
instead of 37-bit.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 is SNOC, not PCI. This prevents probing WCN3990.
Fixes: 367c899f62 ("ath10k: add bus type check in ath10k_init_hw_params")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcG9TEAAoJEG4XJFUm622byW8H/1vMVJhXwgIZbHeoUKNa47Yp
Z7Jv5vW8IGXu+lp7DyoedDCbq4+lskNSlDV1DmysNChLgDnApU/3oCd/jH8EiGPV
JAFUHb85HuVLTTpPpNHtnYz3IzL7r098TNVxOU0VD+xILM0Mf0aCeXztgmFWpGaY
/rfHkId8oKUezIjdu6Dc96mqITrT6WRNtnOMfjr6dZPjClRTS44Hyz3Ga3rXABBL
/n8BCkl0GpKGrL3mBy2CCR5mVY8zfxMB4Aj2zx7bccZ8i2i2QjrGlXCHyB6ImNrR
lv4L1fUVXZWVdeOe8EbpftY7zEsPrX+XNm6h1kckdB7UyuBROpQLsVb+yxlLh9g=
=mhAw
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wmi configuration cmd to configure base band(BB) power amplifier(PA)
off timing values in hardware. The default PA off timings were fine tuned
to make proper DFS radar detection in QCA reference design. If ODM uses
different PA in their design, then the same default PA off timing values
cannot be used, it requires different settling time to detect radar pulses
very sooner and avoid radar detection problems. In that case it provides
provision to select proper PA off timing values based on the PA hardware used.
The PA component is part of FEM hardware and new device tree entry
"ext-fem-name" is used to indentify the FEM hardware. And this wmi configuration
cmd is enabled via wmi service flag "WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT".
Other way is to apply these values through calibration data, but recalibration
of all boards out there might not be feasible.
This change tested on firmware ver 10.2.4-1.0-00042 in QCA988X chipset.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Memory of tx_stats was allocated when a STA was added. But it's not freed
if the STA failed to be added to driver. This issue could be seen in MDK3
attack case when STA number reached the limit.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There was a race condition in SMP that an ath10k_peer was created but its
member sta was null. Following are procedures of ath10k_peer creation and
member sta access in peer statistics path.
1. Peer creation:
ath10k_peer_create()
=>ath10k_wmi_peer_create()
=>ath10k_wait_for_peer_created()
...
# another kernel path, RX from firmware
ath10k_htt_t2h_msg_handler()
=>ath10k_peer_map_event()
=>wake_up()
# ar->peer_map[id] = peer //add peer to map
#wake up original path from waiting
...
# peer->sta = sta //sta assignment
2. RX path of statistics
ath10k_htt_t2h_msg_handler()
=>ath10k_update_per_peer_tx_stats()
=>ath10k_htt_fetch_peer_stats()
# peer->sta //sta accessing
Any access of peer->sta after peer was added to peer_map but before sta was
assigned could cause a null pointer issue. And because these two steps are
asynchronous, no proper lock can protect them. So both peer and sta need to
be checked before access.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The "survey" pointer is the address of an array element. We know that
it can't be NULL so this check can be removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During driver load below warn logs are printed in the console.
Since driver may not implement all wmi events sent by fw and
all of them are non-fatal, move this log to debug level to
remove un-necessary warn message on console.
[ 361.887230] ath10k_snoc a000000.wifi: Unknown eventid: 16393
[ 361.907037] ath10k_snoc a000000.wifi: Unknown eventid: 237569
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The devm_memremap() function doesn't return NULLs, it returns error
pointers.
Fixes: ba94c753cc ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All the necessary patches to make wifi running (over SNOC)
are merged and tested on SDM845/QCS404 platform with WCN3990
wifi module, hence remove work in progress debug from snoc
driver and Kconfig.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some hardwares variants (QCA99x0) are limiting msdu deaggregation with
some threshold value(default limit in QCA99x0 is 64 msdus), it was introduced to
avoid excessive MSDU-deaggregation in error cases. When number of sub frames
exceeds the limit, target hardware will send all msdus starting from present
msdu in RAW format as a single msdu packet and it will be indicated with
error status bit "RX_MSDU_END_INFO0_MSDU_LIMIT_ERR" set in rx descriptor.
This msdu frame is a partial raw MSDU and does't have first msdu and ieee80211
header. It caused below warning message.
[ 320.151332] ------------[ cut here ]------------
[ 320.155006] WARNING: CPU: 0 PID: 3 at drivers/net/wireless/ath/ath10k/htt_rx.c:1188
In our issue case, MSDU limit error happened due to FCS error and generated
this warning message.
This fixes the warning by handling the MSDU limit error. If msdu limit error
happens, driver adds first MSDU's ieee80211 header and sets A-MSDU present bit
in QOS header so that upper layer processes this frame if it is valid or drop it
if FCS error set. And removed the warning message, hence partial msdus without
first msdu is expected in msdu limit error cases.
Tested on QCA9984, Firmware 10.4-3.6-00104
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently in 10.4 FW, all the received 4addr frames are processed for
source port learning which is enabled by default. This learning can't be
disabled by default in FW since it breaks backward compatibility.
Since ath10k uses mac80211 based 4addr mode, source port learning done in
10.4 FW is redundant and also causes issues when 3addr frames are
transmitted/received for a 4addr station.
One such visible functional impact is when GTK rekey frame from
hostapd based AP to 4addr STA is dropped in AP's 10.4 FW. This is since
GTK rekey EAPOL frame is 3addr frame on AP interface and STA enabled
with 4addr is already allowed for receiving 3addr EAPOL frames.
Source port learning implementation in 10.4 FW drops this 3addr GTK rekey
frame in AP destinated for 4addr STA causing disassociation and
re-association for every GTK rekey session. GTK rekey issue is not seen
when learning is disabled in FW.
To prevent such issues without breaking backward compatibility, FW
advertises new service bit making the source port learning configurable and
this learning is being currently disabled during ath10k vdev creation.
* Tested HW: QCA9984
* Tested FW: 10.4-3.6.0.1-00004
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mesh path metric needs tx rate information from ieee80211_tx_status()
call but in ath10k there is no mechanism to report tx rate information
via ieee80211_tx_status(), the tx rate is only accessible via
sta_statiscs() op.
Per peer tx stats has tx rate info available, Tx rate is available
to ath10k driver after every 4 PPDU sent in the air. For each PPDU,
ath10k driver updates rate informattion to mac80211 using
ieee80211_tx_rate_update().
Per peer txrate information is updated through per peer statistics
and is available for QCA9888/QCA9984/QCA4019/QCA998X only
Tested on QCA9984 with firmware-5.bin_10.4-3.5.3-00053
Tested on QCA998X with firmware-5.bin_10.2.4-1.0-00036
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When processing HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND, if the length of a msdu
is larger than the tailroom of the rx skb, skb_over_panic issue will happen
when calling skb_put. In monitor mode, amsdu will be handled in this path, and
msdu_len of the first msdu_desc is the length of the entire amsdu, which might
be larger than the maximum length of a skb, in such case, it will hit the issue
upon.
To fix this issue, process msdu list separately for monitor mode.
Successfully tested with:
QCA6174 (FW version: RM.4.4.1.c2-00057-QCARMSWP-1).
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
[kvalo@codeaurora.org: cosmetic cleanup]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This issue arise in a race condition between ath10k_sta_state() and
ath10k_htt_fetch_peer_stats(), explained in below scenario
Steps:
1. In ath10k_sta_state(), arsta->tx_stats get deallocated before peer deletion
when the station moves from IEEE80211_STA_NONE to IEEE80211_STA_NOTEXIST
state.
2. Meanwhile ath10k receive HTT_T2H_MSG_TYPE_PEER_STATS message.
In ath10k_htt_fetch_peer_stats(), arsta->tx_stats get accessed after
the peer validation check.
Since arsta->tx_stats get freed before the peer deletion [1].
ath10k_htt_fetch_peer_stats() ended up in "use after free" situation.
Fixed this issue by moving the arsta->tx_stats free handling after the
peer deletion. so that ath10k_htt_fetch_peer_stats() will not end up in
"use after free" situation.
Kernel Panic:
Unable to handle kernel NULL pointer dereference at virtual address 00000286
pgd = d8754000
[00000286] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
...
CPU: 0 PID: 6245 Comm: hostapd Not tainted
task: dc44cac0 ti: d4a38000 task.ti: d4a38000
PC is at kmem_cache_alloc+0x7c/0x114
LR is at ath10k_sta_state+0x190/0xd58 [ath10k_core]
pc : [<c02bdc50>] lr : [<bf916b78>] psr: 20000013
sp : d4a39b88 ip : 00000000 fp : 00000001
r10: 00000000 r9 : 1d3bc000 r8 : 00000dc0
r7 : 000080d0 r6 : d4a38000 r5 : dd401b00 r4 : 00000286
r3 : 00000000 r2 : d4a39ba0 r1 : 000080d0 r0 : dd401b00
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5787d Table: 5a75406a DAC: 00000015
Process hostapd (pid: 6245, stack limit = 0xd4a38238)
Stack: (0xd4a39b88 to 0xd4a3a000)
...
[<c02bdc50>] (kmem_cache_alloc) from [<bf916b78>] (ath10k_sta_state+0x190/0xd58 [ath10k_core])
[<bf916b78>] (ath10k_sta_state [ath10k_core]) from [<bf870d4c>] (sta_info_insert_rcu+0x418/0x61c [mac80211])
[<bf870d4c>] (sta_info_insert_rcu [mac80211]) from [<bf88634c>] (ieee80211_add_station+0xf0/0x134 [mac80211])
[<bf88634c>] (ieee80211_add_station [mac80211]) from [<bf83f3c4>] (nl80211_new_station+0x330/0x36c [cfg80211])
[<bf83f3c4>] (nl80211_new_station [cfg80211]) from [<bf6c4040>] (extack_doit+0x2c/0x74 [compat])
[<bf6c4040>] (extack_doit [compat]) from [<c05c285c>] (genl_rcv_msg+0x274/0x30c)
[<c05c285c>] (genl_rcv_msg) from [<c05c1d98>] (netlink_rcv_skb+0x58/0xac)
[<c05c1d98>] (netlink_rcv_skb) from [<c05c25d4>] (genl_rcv+0x20/0x34)
[<c05c25d4>] (genl_rcv) from [<c05c1750>] (netlink_unicast+0x11c/0x204)
[<c05c1750>] (netlink_unicast) from [<c05c1be0>] (netlink_sendmsg+0x30c/0x370)
[<c05c1be0>] (netlink_sendmsg) from [<c0587e90>] (sock_sendmsg+0x70/0x84)
[<c0587e90>] (sock_sendmsg) from [<c058970c>] (___sys_sendmsg.part.3+0x188/0x228)
[<c058970c>] (___sys_sendmsg.part.3) from [<c058a594>] (__sys_sendmsg+0x4c/0x70)
[<c058a594>] (__sys_sendmsg) from [<c0208c80>] (ret_fast_syscall+0x0/0x44)
Code: ebfffec1 e1a04000 ea00001b e5953014 (e7940003)
ath10k_pci 0000:01:00.0: SWBA overrun on vdev 0, skipped old beacon
Hardware tested: QCA9984
Firmware tested: 10.4-3.6.0.1-00004
Fixes: a904417fc ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath10k/mac.c: In function 'ath10k_sta_state':
drivers/net/wireless/ath/ath10k/mac.c:6238:7: warning:
variable 'num_tdls_vifs' set but not used [-Wunused-but-set-variable]
'num_tdls_vifs' not used any more after
9a993cc1ea ("ath10k: fix the logic of limiting tdls peer counts")
Also, remove the single called function ath10k_mac_tdls_vifs_count
and ath10k_mac_tdls_vifs_count_iter.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HL2.0 firmware does not support setting quiet mode. If the host driver sends
the quiet mode setting command to the HL2.0 firmware, it crashes with the below
signature.
fatal error received: err_qdi.c:456:EX:wlan_process:1:WLAN RT:207a:PC=b001b4f0
The quiet mode command support is exposed by the firmware via thermal throttle
wmi service. Enable ath10k thermal support if thermal throttle wmi service bit
is set. 10.x firmware versions support this feature by default, but
unfortunately do not advertise the support via service flags, hence have to
manually set the service flag in ath10k_core_compat_services().
Tested on QCA988X with 10.2.4.70.9-2. Also tested on WCN3990.
Co-developed-by: Govind Singh <govinds@codeaurora.org>
Co-developed-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 4.21. Most notable here is support for
Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide
nvram files for brcmfmac.
Major changes:
brcmfmac
* add support for first trying to get a board specific nvram file
* add support for getting nvram contents from EFI variables
qtnfmac
* use single PCIe driver for all platforms and rename
Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE
* add support for QSR1000/QSR2000 (Topaz) family of chipsets
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
iwlwifi
* PCI IDs for some new 9000-series cards
* improve antenna usage on connection problems
* new firmware debugging infrastructure
* some more work on 802.11ax
* improve support for multiple RF modules with 22000 devices
cordic
* move cordic macros and defines to a public header file
* convert brcmsmac and b43 to fully use cordic library
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcATmGAAoJEG4XJFUm622bk9kH/1RWa2z7Gmjr2wBSLHryvRAH
3FAUSJ4GJPH6MJ5X824srkcVsx2Y1RVt2i+bLXRXLq35aZkrFswohTXVM2h5dU7T
Uy2SL+q9pBUcS7fyv9bE7XV7KsFBJly/5p/wciVRZMnEK6X/w6KkBx/vGvlm5I/C
q196KazbVAYcl6s7KMrfFOYt0Wsto/gdEeesSVBkmcCTEkiKUjjJ4WEDVvAKK+qB
AiwgSdioqYmmEiUuredm6bhVqZG3K2mScoCy95N3jXkiDaKkaYgVtBuAU4Cdju/t
WgLIc9EnUYxXZtwnt889X62P1OkDOtKlj/mjdsGyF0Vrs1W+kErDO0NocOvu2Tk=
=9bL7
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-11-30' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
First set of patches for 4.21. Most notable here is support for
Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide
nvram files for brcmfmac.
Major changes:
brcmfmac
* add support for first trying to get a board specific nvram file
* add support for getting nvram contents from EFI variables
qtnfmac
* use single PCIe driver for all platforms and rename
Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE
* add support for QSR1000/QSR2000 (Topaz) family of chipsets
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
iwlwifi
* PCI IDs for some new 9000-series cards
* improve antenna usage on connection problems
* new firmware debugging infrastructure
* some more work on 802.11ax
* improve support for multiple RF modules with 22000 devices
cordic
* move cordic macros and defines to a public header file
* convert brcmsmac and b43 to fully use cordic library
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211 may call us with vif == NULL, if the station is not currently
active (e.g., not associated). It is trivially easy to reproduce a crash
by suspending the system when not connected to an AP:
[ 65.533934] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
...
[ 65.574521] pc : ath10k_flush+0x30/0xd0 [ath10k_core]
[ 65.574538] lr : __ieee80211_flush_queues+0x180/0x244 [mac80211]
[ 65.599680] Process kworker/u12:1 (pid: 57, stack limit = 0x(____ptrval____))
[ 65.599682] Call trace:
[ 65.599695] ath10k_flush+0x30/0xd0 [ath10k_core]
[ 65.642064] __ieee80211_flush_queues+0x180/0x244 [mac80211]
[ 65.642079] ieee80211_flush_queues+0x34/0x40 [mac80211]
[ 65.642095] __ieee80211_suspend+0xfc/0x47c [mac80211]
[ 65.658611] ieee80211_suspend+0x30/0x3c [mac80211]
[ 65.658627] wiphy_suspend+0x15c/0x3a8 [cfg80211]
[ 65.672810] dpm_run_callback+0xf0/0x1f0
[ 65.672814] __device_suspend+0x3ac/0x4f8
[ 65.672819] async_suspend+0x34/0xbc
[ 65.684096] async_run_entry_fn+0x54/0x104
[ 65.684099] worker_thread+0x4cc/0x72c
[ 65.684102] kthread+0x134/0x13c
[ 65.684105] ret_from_fork+0x10/0x18
Fixes: 9de4162f09 ("ath10k: add peer flush in ath10k_flush for STATION")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
