restore_hv_regs() is used to copy the hv_regs L1 wants to set to run the
nested (L2) guest into the vcpu structure. We need to sanitise these
values to ensure we don't let the L1 guest hypervisor do things we don't
want it to.
We don't let data address watchpoints or completed instruction address
breakpoints be set to match in hypervisor state.
We also don't let L1 enable features in the hypervisor facility status
and control register (HFSCR) for L2 which we have disabled for L1. That
is L2 will get the subset of features which the L0 hypervisor has
enabled for L1 and the features L1 wants to enable for L2. This could
mean we give L1 a hypervisor facility unavailable interrupt for a
facility it thinks it has enabled, however it shouldn't have enabled a
facility it itself doesn't have for the L2 guest.
We sanitise the registers when copying in the L2 hv_regs. We don't need
to sanitise when copying back the L1 hv_regs since these shouldn't be
able to contain invalid values as they're just what was copied out.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a one-reg register identifier which can be used to read and
set the virtual PTCR for the guest. This register identifies the
address and size of the virtual partition table for the guest, which
contains information about the nested guests under this guest.
Migrating this value is the only extra requirement for migrating a
guest which has nested guests (assuming of course that the destination
host supports nested virtualization in the kvm-hv module).
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When running as a nested hypervisor, this avoids reading hypervisor
privileged registers (specifically HFSCR, LPIDR and LPCR) at startup;
instead reasonable default values are used. This also avoids writing
LPIDR in the single-vcpu entry/exit path.
Also, this removes the check for CPU_FTR_HVMODE in kvmppc_mmu_hv_init()
since its only caller already checks this.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is only done at level 0, since only level 0 knows which physical
CPU a vcpu is running on. This does for nested guests what L0 already
did for its own guests, which is to flush the TLB on a pCPU when it
goes to run a vCPU there, and there is another vCPU in the same VM
which previously ran on this pCPU and has now started to run on another
pCPU. This is to handle the situation where the other vCPU touched
a mapping, moved to another pCPU and did a tlbiel (local-only tlbie)
on that new pCPU and thus left behind a stale TLB entry on this pCPU.
This introduces a limit on the the vcpu_token values used in the
H_ENTER_NESTED hcall -- they must now be less than NR_CPUS.
[paulus@ozlabs.org - made prev_cpu array be short[] to reduce
memory consumption.]
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds code to call the H_TLB_INVALIDATE hypercall when running as
a guest, in the cases where we need to invalidate TLBs (or other MMU
caches) as part of managing the mappings for a nested guest. Calling
H_TLB_INVALIDATE lets the nested hypervisor inform the parent
hypervisor about changes to partition-scoped page tables or the
partition table without needing to do hypervisor-privileged tlbie
instructions.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When running a nested (L2) guest the guest (L1) hypervisor will use
the H_TLB_INVALIDATE hcall when it needs to change the partition
scoped page tables or the partition table which it manages. It will
use this hcall in the situations where it would use a partition-scoped
tlbie instruction if it were running in hypervisor mode.
The H_TLB_INVALIDATE hcall can invalidate different scopes:
Invalidate TLB for a given target address:
- This invalidates a single L2 -> L1 pte
- We need to invalidate any L2 -> L0 shadow_pgtable ptes which map the L2
address space which is being invalidated. This is because a single
L2 -> L1 pte may have been mapped with more than one pte in the
L2 -> L0 page tables.
Invalidate the entire TLB for a given LPID or for all LPIDs:
- Invalidate the entire shadow_pgtable for a given nested guest, or
for all nested guests.
Invalidate the PWC (page walk cache) for a given LPID or for all LPIDs:
- We don't cache the PWC, so nothing to do.
Invalidate the entire TLB, PWC and partition table for a given/all LPIDs:
- Here we re-read the partition table entry and remove the nested state
for any nested guest for which the first doubleword of the partition
table entry is now zero.
The H_TLB_INVALIDATE hcall takes as parameters the tlbie instruction
word (of which only the RIC, PRS and R fields are used), the rS value
(giving the lpid, where required) and the rB value (giving the IS, AP
and EPN values).
[paulus@ozlabs.org - adapted to having the partition table in guest
memory, added the H_TLB_INVALIDATE implementation, removed tlbie
instruction emulation, reworded the commit message.]
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When a host (L0) page which is mapped into a (L1) guest is in turn
mapped through to a nested (L2) guest we keep a reverse mapping (rmap)
so that these mappings can be retrieved later.
Whenever we create an entry in a shadow_pgtable for a nested guest we
create a corresponding rmap entry and add it to the list for the
L1 guest memslot at the index of the L1 guest page it maps. This means
at the L1 guest memslot we end up with lists of rmaps.
When we are notified of a host page being invalidated which has been
mapped through to a (L1) guest, we can then walk the rmap list for that
guest page, and find and invalidate all of the corresponding
shadow_pgtable entries.
In order to reduce memory consumption, we compress the information for
each rmap entry down to 52 bits -- 12 bits for the LPID and 40 bits
for the guest real page frame number -- which will fit in a single
unsigned long. To avoid a scenario where a guest can trigger
unbounded memory allocations, we scan the list when adding an entry to
see if there is already an entry with the contents we need. This can
occur, because we don't ever remove entries from the middle of a list.
A struct nested guest rmap is a list pointer and an rmap entry;
----------------
| next pointer |
----------------
| rmap entry |
----------------
Thus the rmap pointer for each guest frame number in the memslot can be
either NULL, a single entry, or a pointer to a list of nested rmap entries.
gfn memslot rmap array
-------------------------
0 | NULL | (no rmap entry)
-------------------------
1 | single rmap entry | (rmap entry with low bit set)
-------------------------
2 | list head pointer | (list of rmap entries)
-------------------------
The final entry always has the lowest bit set and is stored in the next
pointer of the last list entry, or as a single rmap entry.
With a list of rmap entries looking like;
----------------- ----------------- -------------------------
| list head ptr | ----> | next pointer | ----> | single rmap entry |
----------------- ----------------- -------------------------
| rmap entry | | rmap entry |
----------------- -------------------------
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Consider a normal (L1) guest running under the main hypervisor (L0),
and then a nested guest (L2) running under the L1 guest which is acting
as a nested hypervisor. L0 has page tables to map the address space for
L1 providing the translation from L1 real address -> L0 real address;
L1
|
| (L1 -> L0)
|
----> L0
There are also page tables in L1 used to map the address space for L2
providing the translation from L2 real address -> L1 read address. Since
the hardware can only walk a single level of page table, we need to
maintain in L0 a "shadow_pgtable" for L2 which provides the translation
from L2 real address -> L0 real address. Which looks like;
L2 L2
| |
| (L2 -> L1) |
| |
----> L1 | (L2 -> L0)
| |
| (L1 -> L0) |
| |
----> L0 --------> L0
When a page fault occurs while running a nested (L2) guest we need to
insert a pte into this "shadow_pgtable" for the L2 -> L0 mapping. To
do this we need to:
1. Walk the pgtable in L1 memory to find the L2 -> L1 mapping, and
provide a page fault to L1 if this mapping doesn't exist.
2. Use our L1 -> L0 pgtable to convert this L1 address to an L0 address,
or try to insert a pte for that mapping if it doesn't exist.
3. Now we have a L2 -> L0 mapping, insert this into our shadow_pgtable
Once this mapping exists we can take rc faults when hardware is unable
to automatically set the reference and change bits in the pte. On these
we need to:
1. Check the rc bits on the L2 -> L1 pte match, and otherwise reflect
the fault down to L1.
2. Set the rc bits in the L1 -> L0 pte which corresponds to the same
host page.
3. Set the rc bits in the L2 -> L0 pte.
As we reuse a large number of functions in book3s_64_mmu_radix.c for
this we also needed to refactor a number of these functions to take
an lpid parameter so that the correct lpid is used for tlb invalidations.
The functionality however has remained the same.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When we are running as a nested hypervisor, we use a hypercall to
enter the guest rather than code in book3s_hv_rmhandlers.S. This means
that the hypercall handlers listed in hcall_real_table never get called.
There are some hypercalls that are handled there and not in
kvmppc_pseries_do_hcall(), which therefore won't get processed for
a nested guest.
To fix this, we add cases to kvmppc_pseries_do_hcall() to handle those
hypercalls, with the following exceptions:
- The HPT hypercalls (H_ENTER, H_REMOVE, etc.) are not handled because
we only support radix mode for nested guests.
- H_CEDE has to be handled specially because the cede logic in
kvmhv_run_single_vcpu assumes that it has been processed by the time
that kvmhv_p9_guest_entry() returns. Therefore we put a special
case for H_CEDE in kvmhv_p9_guest_entry().
For the XICS hypercalls, if real-mode processing is enabled, then the
virtual-mode handlers assume that they are being called only to finish
up the operation. Therefore we turn off the real-mode flag in the XICS
code when running as a nested hypervisor.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds code to call the H_IPI and H_EOI hypercalls when we are
running as a nested hypervisor (i.e. without the CPU_FTR_HVMODE cpu
feature) and we would otherwise access the XICS interrupt controller
directly or via an OPAL call.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a new hypercall, H_ENTER_NESTED, which is used by a nested
hypervisor to enter one of its nested guests. The hypercall supplies
register values in two structs. Those values are copied by the level 0
(L0) hypervisor (the one which is running in hypervisor mode) into the
vcpu struct of the L1 guest, and then the guest is run until an
interrupt or error occurs which needs to be reported to L1 via the
hypercall return value.
Currently this assumes that the L0 and L1 hypervisors are the same
endianness, and the structs passed as arguments are in native
endianness. If they are of different endianness, the version number
check will fail and the hcall will be rejected.
Nested hypervisors do not support indep_threads_mode=N, so this adds
code to print a warning message if the administrator has set
indep_threads_mode=N, and treat it as Y.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This starts the process of adding the code to support nested HV-style
virtualization. It defines a new H_SET_PARTITION_TABLE hypercall which
a nested hypervisor can use to set the base address and size of a
partition table in its memory (analogous to the PTCR register).
On the host (level 0 hypervisor) side, the H_SET_PARTITION_TABLE
hypercall from the guest is handled by code that saves the virtual
PTCR value for the guest.
This also adds code for creating and destroying nested guests and for
reading the partition table entry for a nested guest from L1 memory.
Each nested guest has its own shadow LPID value, different in general
from the LPID value used by the nested hypervisor to refer to it. The
shadow LPID value is allocated at nested guest creation time.
Nested hypervisor functionality is only available for a radix guest,
which therefore means a radix host on a POWER9 (or later) processor.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
kvmppc_unmap_pte() does a sequence of operations that are open-coded in
kvm_unmap_radix(). This extends kvmppc_unmap_pte() a little so that it
can be used by kvm_unmap_radix(), and makes kvm_unmap_radix() call it.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The radix page fault handler accounts for all cases, including just
needing to insert a pte. This breaks it up into separate functions for
the two main cases; setting rc and inserting a pte.
This allows us to make the setting of rc and inserting of a pte
generic for any pgtable, not specific to the one for this guest.
[paulus@ozlabs.org - reduced diffs from previous code]
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
kvmppc_mmu_radix_xlate() is used to translate an effective address
through the process tables. The process table and partition tables have
identical layout. Exploit this fact to make the kvmppc_mmu_radix_xlate()
function able to translate either an effective address through the
process tables or a guest real address through the partition tables.
[paulus@ozlabs.org - reduced diffs from previous code]
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When destroying a VM we return the LPID to the pool, however we never
zero the partition table entry. This is instead done when we reallocate
the LPID.
Zero the partition table entry on VM teardown before returning the LPID
to the pool. This means if we were running as a nested hypervisor the
real hypervisor could use this to determine when it can free resources.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When the 'regs' field was added to struct kvm_vcpu_arch, the code
was changed to use several of the fields inside regs (e.g., gpr, lr,
etc.) but not the ccr field, because the ccr field in struct pt_regs
is 64 bits on 64-bit platforms, but the cr field in kvm_vcpu_arch is
only 32 bits. This changes the code to use the regs.ccr field
instead of cr, and changes the assembly code on 64-bit platforms to
use 64-bit loads and stores instead of 32-bit ones.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a file called 'radix' in the debugfs directory for the
guest, which when read gives all of the valid leaf PTEs in the
partition-scoped radix tree for a radix guest, in human-readable
format. It is analogous to the existing 'htab' file which dumps
the HPT entries for a HPT guest.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently the code for handling hypervisor instruction page faults
passes 0 for the flags indicating the type of fault, which is OK in
the usual case that the page is not mapped in the partition-scoped
page tables. However, there are other causes for hypervisor
instruction page faults, such as not being to update a reference
(R) or change (C) bit. The cause is indicated in bits in HSRR1,
including a bit which indicates that the fault is due to not being
able to write to a page (for example to update an R or C bit).
Not handling these other kinds of faults correctly can lead to a
loop of continual faults without forward progress in the guest.
In order to handle these faults better, this patch constructs a
"DSISR-like" value from the bits which DSISR and SRR1 (for a HISI)
have in common, and passes it to kvmppc_book3s_hv_page_fault() so
that it knows what caused the fault.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This creates an alternative guest entry/exit path which is used for
radix guests on POWER9 systems when we have indep_threads_mode=Y. In
these circumstances there is exactly one vcpu per vcore and there is
no coordination required between vcpus or vcores; the vcpu can enter
the guest without needing to synchronize with anything else.
The new fast path is implemented almost entirely in C in book3s_hv.c
and runs with the MMU on until the guest is entered. On guest exit
we use the existing path until the point where we are committed to
exiting the guest (as distinct from handling an interrupt in the
low-level code and returning to the guest) and we have pulled the
guest context from the XIVE. At that point we check a flag in the
stack frame to see whether we came in via the old path and the new
path; if we came in via the new path then we go back to C code to do
the rest of the process of saving the guest context and restoring the
host context.
The C code is split into separate functions for handling the
OS-accessible state and the hypervisor state, with the idea that the
latter can be replaced by a hypercall when we implement nested
virtualization.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[mpe: Fix CONFIG_ALTIVEC=n build]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently kvmppc_handle_exit_hv() is called with the vcore lock held
because it is called within a for_each_runnable_thread loop.
However, we already unlock the vcore within kvmppc_handle_exit_hv()
under certain circumstances, and this is safe because (a) any vcpus
that become runnable and are added to the runnable set by
kvmppc_run_vcpu() have their vcpu->arch.trap == 0 and can't actually
run in the guest (because the vcore state is VCORE_EXITING), and
(b) for_each_runnable_thread is safe against addition or removal
of vcpus from the runnable set.
Therefore, in order to simplify things for following patches, let's
drop the vcore lock in the for_each_runnable_thread loop, so
kvmppc_handle_exit_hv() gets called without the vcore lock held.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a parameter to __kvmppc_save_tm and __kvmppc_restore_tm
which allows the caller to indicate whether it wants the nonvolatile
register state to be preserved across the call, as required by the C
calling conventions. This parameter being non-zero also causes the
MSR bits that enable TM, FP, VMX and VSX to be preserved. The
condition register and DSCR are now always preserved.
With this, kvmppc_save_tm_hv and kvmppc_restore_tm_hv can be called
from C code provided the 3rd parameter is non-zero. So that these
functions can be called from modules, they now include code to set
the TOC pointer (r2) on entry, as they can call other built-in C
functions which will assume the TOC to have been set.
Also, the fake suspend code in kvmppc_save_tm_hv is modified here to
assume that treclaim in fake-suspend state does not modify any registers,
which is the case on POWER9. This enables the code to be simplified
quite a bit.
_kvmppc_save_tm_pr and _kvmppc_restore_tm_pr become much simpler with
this change, since they now only need to save and restore TAR and pass
1 for the 3rd argument to __kvmppc_{save,restore}_tm.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This streamlines the first part of the code that handles a hypervisor
interrupt that occurred in the guest. With this, all of the real-mode
handling that occurs is done before the "guest_exit_cont" label; once
we get to that label we are committed to exiting to host virtual mode.
Thus the machine check and HMI real-mode handling is moved before that
label.
Also, the code to handle external interrupts is moved out of line, as
is the code that calls kvmppc_realmode_hmi_handler().
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This pulls out the assembler code that is responsible for saving and
restoring the PMU state for the host and guest into separate functions
so they can be used from an alternate entry path. The calling
convention is made compatible with C.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is based on a patch by Suraj Jitindar Singh.
This moves the code in book3s_hv_rmhandlers.S that generates an
external, decrementer or privileged doorbell interrupt just before
entering the guest to C code in book3s_hv_builtin.c. This is to
make future maintenance and modification easier. The algorithm
expressed in the C code is almost identical to the previous
algorithm.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This removes code that clears the external interrupt pending bit in
the pending_exceptions bitmap. This is left over from an earlier
iteration of the code where this bit was set when an escalation
interrupt arrived in order to wake the vcpu from cede. Currently
we set the vcpu->arch.irq_pending flag instead for this purpose.
Therefore there is no need to do anything with the pending_exceptions
bitmap.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently we use two bits in the vcpu pending_exceptions bitmap to
indicate that an external interrupt is pending for the guest, one
for "one-shot" interrupts that are cleared when delivered, and one
for interrupts that persist until cleared by an explicit action of
the OS (e.g. an acknowledge to an interrupt controller). The
BOOK3S_IRQPRIO_EXTERNAL bit is used for one-shot interrupt requests
and BOOK3S_IRQPRIO_EXTERNAL_LEVEL is used for persisting interrupts.
In practice BOOK3S_IRQPRIO_EXTERNAL never gets used, because our
Book3S platforms generally, and pseries in particular, expect
external interrupt requests to persist until they are acknowledged
at the interrupt controller. That combined with the confusion
introduced by having two bits for what is essentially the same thing
makes it attractive to simplify things by only using one bit. This
patch does that.
With this patch there is only BOOK3S_IRQPRIO_EXTERNAL, and by default
it has the semantics of a persisting interrupt. In order to avoid
breaking the ABI, we introduce a new "external_oneshot" flag which
preserves the behaviour of the KVM_INTERRUPT ioctl with the
KVM_INTERRUPT_SET argument.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The kvmppc_gpa_to_ua() helper itself takes care of the permission
bits in the TCE and yet every single caller removes them.
This changes semantics of kvmppc_gpa_to_ua() so it takes TCEs
(which are GPAs + TCE permission bits) to make the callers simpler.
This should cause no behavioural change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At the moment if the PUT_TCE{_INDIRECT} handlers fail to update
the hardware tables, we print a warning once, clear the entry and
continue. This is so as at the time the assumption was that if
a VFIO device is hotplugged into the guest, and the userspace replays
virtual DMA mappings (i.e. TCEs) to the hardware tables and if this fails,
then there is nothing useful we can do about it.
However the assumption is not valid as these handlers are not called for
TCE replay (VFIO ioctl interface is used for that) and these handlers
are for new TCEs.
This returns an error to the guest if there is a request which cannot be
processed. By now the only possible failure must be H_TOO_HARD.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The userspace can request an arbitrary supported page size for a DMA
window and this works fine as long as the mapped memory is backed with
the pages of the same or bigger size; if this is not the case,
mm_iommu_ua_to_hpa{_rm}() fail and tables do not populated with
dangerously incorrect TCEs.
However since it is quite easy to misconfigure the KVM and we do not do
reverts to all changes made to TCE tables if an error happens in a middle,
we better do the acceptable page size validation before we even touch
the tables.
This enhances kvmppc_tce_validate() to check the hardware IOMMU page sizes
against the preregistered memory page sizes.
Since the new check uses real/virtual mode helpers, this renames
kvmppc_tce_validate() to kvmppc_rm_tce_validate() to handle the real mode
case and mirrors it for the virtual mode under the old name. The real
mode handler is not used for the virtual mode as:
1. it uses _lockless() list traversing primitives instead of RCU;
2. realmode's mm_iommu_ua_to_hpa_rm() uses vmalloc_to_phys() which
virtual mode does not have to use and since on POWER9+radix only virtual
mode handlers actually work, we do not want to slow down that path even
a bit.
This removes EXPORT_SYMBOL_GPL(kvmppc_tce_validate) as the validators
are static now.
From now on the attempts on mapping IOMMU pages bigger than allowed
will result in KVM exit.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[mpe: Fix KVM_HV=n build]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a mode where the vcore scheduling logic in HV KVM limits itself
to scheduling only virtual cores from the same VM on any given physical
core. This is enabled via a new module parameter on the kvm-hv module
called "one_vm_per_core". For this to work on POWER9, it is necessary to
set indep_threads_mode=N. (On POWER8, hardware limitations mean that KVM
is never in independent threads mode, regardless of the indep_threads_mode
setting.)
Thus the settings needed for this to work are:
1. The host is in SMT1 mode.
2. On POWER8, the host is not in 2-way or 4-way static split-core mode.
3. On POWER9, the indep_threads_mode parameter is N.
4. The one_vm_per_core parameter is Y.
With these settings, KVM can run up to 4 vcpus on a core at the same
time on POWER9, or up to 8 vcpus on POWER8 (depending on the guest
threading mode), and will ensure that all of the vcpus belong to the
same VM.
This is intended for use in security-conscious settings where users are
concerned about possible side-channel attacks between threads which could
perhaps enable one VM to attack another VM on the same core, or the host.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When an OS (currently only classic Mac OS) is running in KVM-PR and makes a
linked jump from code with split hack addressing enabled into code that does
not, LR is not correctly updated and reflects the previously munged PC.
To fix this, this patch undoes the address munge when exiting split
hack mode so that code relying on LR being a proper address will now
execute. This does not affect OS X or other operating systems running
on KVM-PR.
Signed-off-by: Cameron Kaiser <spectre@floodgap.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Commit 71d29f43b6 ("KVM: PPC: Book3S HV: Don't use compound_order to
determine host mapping size", 2018-09-11) added a call to
__find_linux_pte() and a dereference of the returned PTE pointer to the
radix page fault path in the common case where the page is normal
system memory. Previously, __find_linux_pte() was only called for
mappings to physical addresses which don't have a page struct (e.g.
memory-mapped I/O) or where the page struct is marked as reserved
memory.
This exposes us to the possibility that the returned PTE pointer
could be NULL, for example in the case of a concurrent THP collapse
operation. Dereferencing the returned NULL pointer causes a host
crash.
To fix this, we check for NULL, and if it is NULL, we retry the
operation by returning to the guest, with the expectation that it
will generate the same page fault again (unless of course it has
been fixed up by another CPU in the meantime).
Fixes: 71d29f43b6 ("KVM: PPC: Book3S HV: Don't use compound_order to determine host mapping size")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
We return H_TOO_HARD from TCE update handlers when we think that
the next handler (realmode -> virtual mode -> user mode) has a chance to
handle the request; H_HARDWARE/H_CLOSED otherwise.
This changes the handlers to return H_TOO_HARD on every error giving
the userspace an opportunity to handle any request or at least log
them all.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The KVM TCE handlers are written in a way so they fail when either
something went horribly wrong or the userspace did some obvious mistake
such as passing a misaligned address.
We are going to enhance the TCE checker to fail on attempts to map bigger
IOMMU page than the underlying pinned memory so let's valitate TCE
beforehand.
This should cause no behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
THP paths can defer splitting compound pages until after the actual
remap and TLB flushes to split a huge PMD/PUD. This causes radix
partition scope page table mappings to get out of synch with the host
qemu page table mappings.
This results in random memory corruption in the guest when running
with THP. The easiest way to reproduce is use KVM balloon to free up
a lot of memory in the guest and then shrink the balloon to give the
memory back, while some work is being done in the guest.
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.ibm.com>
Cc: kvm-ppc@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
At the moment the real mode handler of H_PUT_TCE calls iommu_tce_xchg_rm()
which in turn reads the old TCE and if it was a valid entry, marks
the physical page dirty if it was mapped for writing. Since it is in
real mode, realmode_pfn_to_page() is used instead of pfn_to_page()
to get the page struct. However SetPageDirty() itself reads the compound
page head and returns a virtual address for the head page struct and
setting dirty bit for that kills the system.
This adds additional dirty bit tracking into the MM/IOMMU API for use
in the real mode. Note that this does not change how VFIO and
KVM (in virtual mode) set this bit. The KVM (real mode) changes include:
- use the lowest bit of the cached host phys address to carry
the dirty bit;
- mark pages dirty when they are unpinned which happens when
the preregistered memory is released which always happens in virtual
mode;
- add mm_iommu_ua_mark_dirty_rm() helper to set delayed dirty bit;
- change iommu_tce_xchg_rm() to take the kvm struct for the mm to use
in the new mm_iommu_ua_mark_dirty_rm() helper;
- move iommu_tce_xchg_rm() to book3s_64_vio_hv.c (which is the only
caller anyway) to reduce the real mode KVM and IOMMU knowledge
across different subsystems.
This removes realmode_pfn_to_page() as it is not used anymore.
While we at it, remove some EXPORT_SYMBOL_GPL() as that code is for
the real mode only and modules cannot call it anyway.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Two small fixes for KVM on POWER machines; one fixes a bug where pages
might not get marked dirty, causing guest memory corruption on migration,
and the other fixes a bug causing reads from guest memory to use the
wrong guest real address for very large HPT guests (>256G of memory),
leading to failures in instruction emulation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJbfVFcAAoJEJ2a6ncsY3GfwAcH/i4BDNm5bSXLbCZv1Zqc9iWM
ZqCNSlx9fuR5z+Bl3FWvm14CqfG7JFMd1pVXVD3AEGN6nv0mtLPotmoaw+BUWXIP
aD3BRIBSfOVHj90CiWJ1pqZGzE49vAKrjUGocuqHhBiqGjYmnnE7QKgD+lQ13SND
LWDV3XaQgoO9+NZdqtV6hsWMmKCmXWIHykkG9H+EVkD+341e2EBQf6r83qibAGz4
U5SHkr/3JqL8oC7RJixT8CS/dV5qCgmuL8Vs5NYDTUnc6DmKhdes2s7OiugK7nHg
twKe8K0aRVowmTA8yIwEN22OeH1FAUmYDClkgHozHFWyD2+u7O9kLrAYZxEN9Q4=
=61nR
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-fixes-4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
PPC KVM fixes for 4.19
Two small fixes for KVM on POWER machines; one fixes a bug where pages
might not get marked dirty, causing guest memory corruption on migration,
and the other fixes a bug causing reads from guest memory to use the
wrong guest real address for very large HPT guests (>256G of memory),
leading to failures in instruction emulation.
- An implementation for the newly added hv_ops->flush() for the OPAL hvc
console driver backends, I forgot to apply this after merging the hvc driver
changes before the merge window.
- Enable all PCI bridges at boot on powernv, to avoid races when multiple
children of a bridge try to enable it simultaneously. This is a workaround
until the PCI core can be enhanced to fix the races.
- A fix to query PowerVM for the correct system topology at boot before
initialising sched domains, seen in some configurations to cause broken
scheduling etc.
- A fix for pte_access_permitted() on "nohash" platforms.
- Two commits to fix SIGBUS when using remap_pfn_range() seen on Power9 due to
a workaround when using the nest MMU (GPUs, accelerators).
- Another fix to the VFIO code used by KVM, the previous fix had some bugs
which caused guests to not start in some configurations.
- A handful of other minor fixes.
Thanks to:
Aneesh Kumar K.V, Benjamin Herrenschmidt, Christophe Leroy, Hari Bathini, Luke
Dashjr, Mahesh Salgaonkar, Nicholas Piggin, Paul Mackerras, Srikar Dronamraju.
-----BEGIN PGP SIGNATURE-----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=1AUa
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- An implementation for the newly added hv_ops->flush() for the OPAL
hvc console driver backends, I forgot to apply this after merging the
hvc driver changes before the merge window.
- Enable all PCI bridges at boot on powernv, to avoid races when
multiple children of a bridge try to enable it simultaneously. This
is a workaround until the PCI core can be enhanced to fix the races.
- A fix to query PowerVM for the correct system topology at boot before
initialising sched domains, seen in some configurations to cause
broken scheduling etc.
- A fix for pte_access_permitted() on "nohash" platforms.
- Two commits to fix SIGBUS when using remap_pfn_range() seen on Power9
due to a workaround when using the nest MMU (GPUs, accelerators).
- Another fix to the VFIO code used by KVM, the previous fix had some
bugs which caused guests to not start in some configurations.
- A handful of other minor fixes.
Thanks to: Aneesh Kumar K.V, Benjamin Herrenschmidt, Christophe Leroy,
Hari Bathini, Luke Dashjr, Mahesh Salgaonkar, Nicholas Piggin, Paul
Mackerras, Srikar Dronamraju.
* tag 'powerpc-4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mce: Fix SLB rebolting during MCE recovery path.
KVM: PPC: Book3S: Fix guest DMA when guest partially backed by THP pages
powerpc/mm/radix: Only need the Nest MMU workaround for R -> RW transition
powerpc/mm/books3s: Add new pte bit to mark pte temporarily invalid.
powerpc/nohash: fix pte_access_permitted()
powerpc/topology: Get topology for shared processors at boot
powerpc64/ftrace: Include ftrace.h needed for enable/disable calls
powerpc/powernv/pci: Work around races in PCI bridge enabling
powerpc/fadump: cleanup crash memory ranges support
powerpc/powernv: provide a console flush operation for opal hvc driver
powerpc/traps: Avoid rate limit messages from show unhandled signals
powerpc/64s: Fix PACA_IRQ_HARD_DIS accounting in idle_power4()
Also add these typos to spelling.txt so checkpatch.pl will look for them.
Link: http://lkml.kernel.org/r/88af06b9de34d870cb0afc46cfd24e0458be2575.1529471371.git.fthain@telegraphics.com.au
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
this_cpu_disable_ftrace and this_cpu_enable_ftrace are inlines in
ftrace.h Without it included, the build fails.
Fixes: a4bc64d305 ("powerpc64/ftrace: Disable ftrace during kvm entry/exit")
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Luke Dashjr <luke-jr+git@utopios.org>
Acked-by: Naveen N. Rao <naveen.n.rao at linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This fixes a bug which causes guest virtual addresses to get translated
to guest real addresses incorrectly when the guest is using the HPT MMU
and has more than 256GB of RAM, or more specifically has a HPT larger
than 2GB. This has showed up in testing as a failure of the host to
emulate doorbell instructions correctly on POWER9 for HPT guests with
more than 256GB of RAM.
The bug is that the HPTE index in kvmppc_mmu_book3s_64_hv_xlate()
is stored as an int, and in forming the HPTE address, the index gets
shifted left 4 bits as an int before being signed-extended to 64 bits.
The simple fix is to make the variable a long int, matching the
return type of kvmppc_hv_find_lock_hpte(), which is what calculates
the index.
Fixes: 697d3899dc ("KVM: PPC: Implement MMIO emulation support for Book3S HV guests")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
For x86 this brings in PCID emulation and CR3 caching for shadow page
tables, nested VMX live migration, nested VMCS shadowing, an optimized
IPI hypercall, and some optimizations.
ARM will come next week.
There is a semantic conflict because tip also added an .init_platform
callback to kvm.c. Please keep the initializer from this branch,
and add a call to kvmclock_init (added by tip) inside kvm_init_platform
(added here).
Also, there is a backmerge from 4.18-rc6. This is because of a
refactoring that conflicted with a relatively late bugfix and
resulted in a particularly hellish conflict. Because the conflict
was only due to unfortunate timing of the bugfix, I backmerged and
rebased the refactoring rather than force the resolution on you.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJbdwNFAAoJEL/70l94x66DiPEH/1cAGZWGd85Y3yRu1dmTmqiz
kZy0V+WTQ5kyJF4ZsZKKOp+xK7Qxh5e9kLdTo70uPZCHwLu9IaGKN9+dL9Jar3DR
yLPX5bMsL8UUed9g9mlhdaNOquWi7d7BseCOnIyRTolb+cqnM5h3sle0gqXloVrS
UQb4QogDz8+86czqR8tNfazjQRKW/D2HEGD5NDNVY1qtpY+leCDAn9/u6hUT5c6z
EtufgyDh35UN+UQH0e2605gt3nN3nw3FiQJFwFF1bKeQ7k5ByWkuGQI68XtFVhs+
2WfqL3ftERkKzUOy/WoSJX/C9owvhMcpAuHDGOIlFwguNGroZivOMVnACG1AI3I=
=9Mgw
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull first set of KVM updates from Paolo Bonzini:
"PPC:
- minor code cleanups
x86:
- PCID emulation and CR3 caching for shadow page tables
- nested VMX live migration
- nested VMCS shadowing
- optimized IPI hypercall
- some optimizations
ARM will come next week"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (85 commits)
kvm: x86: Set highest physical address bits in non-present/reserved SPTEs
KVM/x86: Use CC_SET()/CC_OUT in arch/x86/kvm/vmx.c
KVM: X86: Implement PV IPIs in linux guest
KVM: X86: Add kvm hypervisor init time platform setup callback
KVM: X86: Implement "send IPI" hypercall
KVM/x86: Move X86_CR4_OSXSAVE check into kvm_valid_sregs()
KVM: x86: Skip pae_root shadow allocation if tdp enabled
KVM/MMU: Combine flushing remote tlb in mmu_set_spte()
KVM: vmx: skip VMWRITE of HOST_{FS,GS}_BASE when possible
KVM: vmx: skip VMWRITE of HOST_{FS,GS}_SEL when possible
KVM: vmx: always initialize HOST_{FS,GS}_BASE to zero during setup
KVM: vmx: move struct host_state usage to struct loaded_vmcs
KVM: vmx: compute need to reload FS/GS/LDT on demand
KVM: nVMX: remove a misleading comment regarding vmcs02 fields
KVM: vmx: rename __vmx_load_host_state() and vmx_save_host_state()
KVM: vmx: add dedicated utility to access guest's kernel_gs_base
KVM: vmx: track host_state.loaded using a loaded_vmcs pointer
KVM: vmx: refactor segmentation code in vmx_save_host_state()
kvm: nVMX: Fix fault priority for VMX operations
kvm: nVMX: Fix fault vector for VMX operation at CPL > 0
...
Merge updates from Andrew Morton:
- a few misc things
- a few Y2038 fixes
- ntfs fixes
- arch/sh tweaks
- ocfs2 updates
- most of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (111 commits)
mm/hmm.c: remove unused variables align_start and align_end
fs/userfaultfd.c: remove redundant pointer uwq
mm, vmacache: hash addresses based on pmd
mm/list_lru: introduce list_lru_shrink_walk_irq()
mm/list_lru.c: pass struct list_lru_node* as an argument to __list_lru_walk_one()
mm/list_lru.c: move locking from __list_lru_walk_one() to its caller
mm/list_lru.c: use list_lru_walk_one() in list_lru_walk_node()
mm, swap: make CONFIG_THP_SWAP depend on CONFIG_SWAP
mm/sparse: delete old sparse_init and enable new one
mm/sparse: add new sparse_init_nid() and sparse_init()
mm/sparse: move buffer init/fini to the common place
mm/sparse: use the new sparse buffer functions in non-vmemmap
mm/sparse: abstract sparse buffer allocations
mm/hugetlb.c: don't zero 1GiB bootmem pages
mm, page_alloc: double zone's batchsize
mm/oom_kill.c: document oom_lock
mm/hugetlb: remove gigantic page support for HIGHMEM
mm, oom: remove sleep from under oom_lock
kernel/dma: remove unsupported gfp_mask parameter from dma_alloc_from_contiguous()
mm/cma: remove unsupported gfp_mask parameter from cma_alloc()
...
cma_alloc() doesn't really support gfp flags other than __GFP_NOWARN, so
convert gfp_mask parameter to boolean no_warn parameter.
This will help to avoid giving false feeling that this function supports
standard gfp flags and callers can pass __GFP_ZERO to get zeroed buffer,
what has already been an issue: see commit dd65a941f6 ("arm64:
dma-mapping: clear buffers allocated with FORCE_CONTIGUOUS flag").
Link: http://lkml.kernel.org/r/20180709122019eucas1p2340da484acfcc932537e6014f4fd2c29~-sqTPJKij2939229392eucas1p2j@eucas1p2.samsung.com
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Michał Nazarewicz <mina86@mina86.com>
Acked-by: Laura Abbott <labbott@redhat.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Joonsoo Kim <js1304@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Notable changes:
- A fix for a bug in our page table fragment allocator, where a page table page
could be freed and reallocated for something else while still in use, leading
to memory corruption etc. The fix reuses pt_mm in struct page (x86 only) for
a powerpc only refcount.
- Fixes to our pkey support. Several are user-visible changes, but bring us in
to line with x86 behaviour and/or fix outright bugs. Thanks to Florian Weimer
for reporting many of these.
- A series to improve the hvc driver & related OPAL console code, which have
been seen to cause hardlockups at times. The hvc driver changes in particular
have been in linux-next for ~month.
- Increase our MAX_PHYSMEM_BITS to 128TB when SPARSEMEM_VMEMMAP=y.
- Remove Power8 DD1 and Power9 DD1 support, neither chip should be in use
anywhere other than as a paper weight.
- An optimised memcmp implementation using Power7-or-later VMX instructions
- Support for barrier_nospec on some NXP CPUs.
- Support for flushing the count cache on context switch on some IBM CPUs
(controlled by firmware), as a Spectre v2 mitigation.
- A series to enhance the information we print on unhandled signals to bring it
into line with other arches, including showing the offending VMA and dumping
the instructions around the fault.
Thanks to:
Aaro Koskinen, Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Alexey
Spirkov, Alistair Popple, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar,
Arnd Bergmann, Bartosz Golaszewski, Benjamin Herrenschmidt, Bharat Bhushan,
Bjoern Noetel, Boqun Feng, Breno Leitao, Bryant G. Ly, Camelia Groza,
Christophe Leroy, Christoph Hellwig, Cyril Bur, Dan Carpenter, Daniel Klamt,
Darren Stevens, Dave Young, David Gibson, Diana Craciun, Finn Thain, Florian
Weimer, Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven, Geoff Levand,
Guenter Roeck, Gustavo Romero, Haren Myneni, Hari Bathini, Joel Stanley,
Jonathan Neuschäfer, Kees Cook, Madhavan Srinivasan, Mahesh Salgaonkar, Markus
Elfring, Mathieu Malaterre, Mauro S. M. Rodrigues, Michael Hanselmann, Michael
Neuling, Michael Schmitz, Mukesh Ojha, Murilo Opsfelder Araujo, Nicholas
Piggin, Parth Y Shah, Paul Mackerras, Paul Menzel, Ram Pai, Randy Dunlap,
Rashmica Gupta, Reza Arbab, Rodrigo R. Galvao, Russell Currey, Sam Bobroff,
Scott Wood, Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stan Johnson,
Thiago Jung Bauermann, Tyrel Datwyler, Vaibhav Jain, Vasant Hegde, Venkat Rao
B, zhong jiang.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCgAxFiEEJFGtCPCthwEv2Y/bUevqPMjhpYAFAlt2O6cTHG1wZUBlbGxl
cm1hbi5pZC5hdQAKCRBR6+o8yOGlgC7hD/4+cj796Df7GsVsIMxzQm7SS9dklIdO
JuKj2Nr5HRzTH59jWlXukLG9mfTNCFgFJB4gEpK1ArDOTcHTCI9RRsLZTZ/kum66
7Pd+7T40dLYXB5uecuUs0vMXa2fI3syKh1VLzACSXv3Dh9BBIKQBwW/aD2eww4YI
1fS5LnXZ2PSxfr6KNAC6ogZnuaiD0sHXOYrtGHq+S/TFC7+Z6ySa6+AnPS+hPVoo
/rHDE1Khr66aj7uk+PP2IgUrCFj6Sbj6hTVlS/iAuwbMjUl9ty6712PmvX9x6wMZ
13hJQI+g6Ci+lqLKqmqVUpXGSr6y4NJGPS/Hko4IivBTJApI+qV/tF2H9nxU+6X0
0RqzsMHPHy13n2torA1gC7ttzOuXPI4hTvm6JWMSsfmfjTxLANJng3Dq3ejh6Bqw
76EMowpDLexwpy7/glPpqNdsP4ySf2Qm8yq3mR7qpL4m3zJVRGs11x+s5DW8NKBL
Fl5SqZvd01abH+sHwv6NLaLkEtayUyohxvyqu2RU3zu5M5vi7DhqstybTPjKPGu0
icSPh7b2y10WpOUpC6lxpdi8Me8qH47mVc/trZ+SpgBrsuEmtJhGKszEnzRCOqos
o2IhYHQv3lQv86kpaAFQlg/RO+Lv+Lo5qbJ209V+hfU5nYzXpEulZs4dx1fbA+ze
fK8GEh+u0L4uJg==
=PzRz
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- A fix for a bug in our page table fragment allocator, where a page
table page could be freed and reallocated for something else while
still in use, leading to memory corruption etc. The fix reuses
pt_mm in struct page (x86 only) for a powerpc only refcount.
- Fixes to our pkey support. Several are user-visible changes, but
bring us in to line with x86 behaviour and/or fix outright bugs.
Thanks to Florian Weimer for reporting many of these.
- A series to improve the hvc driver & related OPAL console code,
which have been seen to cause hardlockups at times. The hvc driver
changes in particular have been in linux-next for ~month.
- Increase our MAX_PHYSMEM_BITS to 128TB when SPARSEMEM_VMEMMAP=y.
- Remove Power8 DD1 and Power9 DD1 support, neither chip should be in
use anywhere other than as a paper weight.
- An optimised memcmp implementation using Power7-or-later VMX
instructions
- Support for barrier_nospec on some NXP CPUs.
- Support for flushing the count cache on context switch on some IBM
CPUs (controlled by firmware), as a Spectre v2 mitigation.
- A series to enhance the information we print on unhandled signals
to bring it into line with other arches, including showing the
offending VMA and dumping the instructions around the fault.
Thanks to: Aaro Koskinen, Akshay Adiga, Alastair D'Silva, Alexey
Kardashevskiy, Alexey Spirkov, Alistair Popple, Andrew Donnellan,
Aneesh Kumar K.V, Anju T Sudhakar, Arnd Bergmann, Bartosz Golaszewski,
Benjamin Herrenschmidt, Bharat Bhushan, Bjoern Noetel, Boqun Feng,
Breno Leitao, Bryant G. Ly, Camelia Groza, Christophe Leroy, Christoph
Hellwig, Cyril Bur, Dan Carpenter, Daniel Klamt, Darren Stevens, Dave
Young, David Gibson, Diana Craciun, Finn Thain, Florian Weimer,
Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven, Geoff Levand,
Guenter Roeck, Gustavo Romero, Haren Myneni, Hari Bathini, Joel
Stanley, Jonathan Neuschäfer, Kees Cook, Madhavan Srinivasan, Mahesh
Salgaonkar, Markus Elfring, Mathieu Malaterre, Mauro S. M. Rodrigues,
Michael Hanselmann, Michael Neuling, Michael Schmitz, Mukesh Ojha,
Murilo Opsfelder Araujo, Nicholas Piggin, Parth Y Shah, Paul
Mackerras, Paul Menzel, Ram Pai, Randy Dunlap, Rashmica Gupta, Reza
Arbab, Rodrigo R. Galvao, Russell Currey, Sam Bobroff, Scott Wood,
Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stan Johnson, Thiago
Jung Bauermann, Tyrel Datwyler, Vaibhav Jain, Vasant Hegde, Venkat
Rao, zhong jiang"
* tag 'powerpc-4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (234 commits)
powerpc/mm/book3s/radix: Add mapping statistics
powerpc/uaccess: Enable get_user(u64, *p) on 32-bit
powerpc/mm/hash: Remove unnecessary do { } while(0) loop
powerpc/64s: move machine check SLB flushing to mm/slb.c
powerpc/powernv/idle: Fix build error
powerpc/mm/tlbflush: update the mmu_gather page size while iterating address range
powerpc/mm: remove warning about ‘type’ being set
powerpc/32: Include setup.h header file to fix warnings
powerpc: Move `path` variable inside DEBUG_PROM
powerpc/powermac: Make some functions static
powerpc/powermac: Remove variable x that's never read
cxl: remove a dead branch
powerpc/powermac: Add missing include of header pmac.h
powerpc/kexec: Use common error handling code in setup_new_fdt()
powerpc/xmon: Add address lookup for percpu symbols
powerpc/mm: remove huge_pte_offset_and_shift() prototype
powerpc/lib: Use patch_site to patch copy_32 functions once cache is enabled
powerpc/pseries: Fix endianness while restoring of r3 in MCE handler.
powerpc/fadump: merge adjacent memory ranges to reduce PT_LOAD segements
powerpc/fadump: handle crash memory ranges array index overflow
...
Since commit e641a31783 ("KVM: PPC: Book3S HV: Unify dirty page map
between HPT and radix", 2017-10-26), kvm_unmap_radix() computes the
number of PAGE_SIZEd pages being unmapped and passes it to
kvmppc_update_dirty_map(), which expects to be passed the page size
instead. Consequently it will only mark one system page dirty even
when a large page (for example a THP page) is being unmapped. The
consequence of this is that part of the THP page might not get copied
during live migration, resulting in memory corruption for the guest.
This fixes it by computing and passing the page size in kvm_unmap_radix().
Cc: stable@vger.kernel.org # v4.15+
Fixes: e641a31783 (KVM: PPC: Book3S HV: Unify dirty page map between HPT and radix)
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAltU8z0eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG5X8H/2fJr7m3k242+t76
sitwvx1eoPqTgryW59dRKm9IuXAGA+AjauvHzaz1QxomeQa50JghGWefD0eiJfkA
1AphQ/24EOiAbbVk084dAI/C2p122dE4D5Fy7CrfLnuouyrbFaZI5STbnrRct7sR
9deeYW0GDHO1Uenp4WDCj0baaqJqaevZ+7GG09DnWpya2nQtSkGBjqn6GpYmrfOU
mqFuxAX8mEOW6cwK16y/vYtnVjuuMAiZ63/OJ8AQ6d6ArGLwAsdn7f8Fn4I4tEr2
L0d3CRLUyegms4++Dmlu05k64buQu46WlPhjCZc5/Ts4kjrNxBuHejj2/jeSnUSt
vJJlibI=
=42a5
-----END PGP SIGNATURE-----
Merge tag 'v4.18-rc6' into HEAD
Pull bug fixes into the KVM development tree to avoid nasty conflicts.
asm/tlbflush.h is only needed for:
- using functions xxx_flush_tlb_xxx()
- using MMU_NO_CONTEXT
- including asm-generic/pgtable.h
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
files not using feature fixup don't need asm/feature-fixups.h
files using feature fixup need asm/feature-fixups.h
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Only include linux/stringify.h is files using __stringify()
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch moves ASM_CONST() and stringify_in_c() into
dedicated asm-const.h, then cleans all related inclusions.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: asm-compat.h should include asm-const.h]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 1e175d2 ("KVM: PPC: Book3S HV: Pack VCORE IDs to access full
VCPU ID space", 2018-07-25) added code that uses kvm->arch.emul_smt_mode
before any VCPUs are created. However, userspace can change
kvm->arch.emul_smt_mode at any time up until the first VCPU is created.
Hence it is (theoretically) possible for the check in
kvmppc_core_vcpu_create_hv() to race with another userspace thread
changing kvm->arch.emul_smt_mode.
This fixes it by moving the test that uses kvm->arch.emul_smt_mode into
the block where kvm->lock is held.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
It is not currently possible to create the full number of possible
VCPUs (KVM_MAX_VCPUS) on Power9 with KVM-HV when the guest uses fewer
threads per core than its core stride (or "VSMT mode"). This is
because the VCORE ID and XIVE offsets grow beyond KVM_MAX_VCPUS
even though the VCPU ID is less than KVM_MAX_VCPU_ID.
To address this, "pack" the VCORE ID and XIVE offsets by using
knowledge of the way the VCPU IDs will be used when there are fewer
guest threads per core than the core stride. The primary thread of
each core will always be used first. Then, if the guest uses more than
one thread per core, these secondary threads will sequentially follow
the primary in each core.
So, the only way an ID above KVM_MAX_VCPUS can be seen, is if the
VCPUs are being spaced apart, so at least half of each core is empty,
and IDs between KVM_MAX_VCPUS and (KVM_MAX_VCPUS * 2) can be mapped
into the second half of each core (4..7, in an 8-thread core).
Similarly, if IDs above KVM_MAX_VCPUS * 2 are seen, at least 3/4 of
each core is being left empty, and we can map down into the second and
third quarters of each core (2, 3 and 5, 6 in an 8-thread core).
Lastly, if IDs above KVM_MAX_VCPUS * 4 are seen, only the primary
threads are being used and 7/8 of the core is empty, allowing use of
the 1, 5, 3 and 7 thread slots.
(Strides less than 8 are handled similarly.)
This allows the VCORE ID or offset to be calculated quickly from the
VCPU ID or XIVE server numbers, without access to the VCPU structure.
[paulus@ozlabs.org - tidied up comment a little, changed some WARN_ONCE
to pr_devel, wrapped line, fixed id check.]
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
A VM which has:
- a DMA capable device passed through to it (eg. network card);
- running a malicious kernel that ignores H_PUT_TCE failure;
- capability of using IOMMU pages bigger that physical pages
can create an IOMMU mapping that exposes (for example) 16MB of
the host physical memory to the device when only 64K was allocated to the VM.
The remaining 16MB - 64K will be some other content of host memory, possibly
including pages of the VM, but also pages of host kernel memory, host
programs or other VMs.
The attacking VM does not control the location of the page it can map,
and is only allowed to map as many pages as it has pages of RAM.
We already have a check in drivers/vfio/vfio_iommu_spapr_tce.c that
an IOMMU page is contained in the physical page so the PCI hardware won't
get access to unassigned host memory; however this check is missing in
the KVM fastpath (H_PUT_TCE accelerated code). We were lucky so far and
did not hit this yet as the very first time when the mapping happens
we do not have tbl::it_userspace allocated yet and fall back to
the userspace which in turn calls VFIO IOMMU driver, this fails and
the guest does not retry,
This stores the smallest preregistered page size in the preregistered
region descriptor and changes the mm_iommu_xxx API to check this against
the IOMMU page size.
This calculates maximum page size as a minimum of the natural region
alignment and compound page size. For the page shift this uses the shift
returned by find_linux_pte() which indicates how the page is mapped to
the current userspace - if the page is huge and this is not a zero, then
it is a leaf pte and the page is mapped within the range.
Fixes: 121f80ba68 ("KVM: PPC: VFIO: Add in-kernel acceleration for VFIO")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The constants are 64bit but not explicitly declared UL resulting
in sparse warnings. Fix this by declaring the constants UL.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The call to of_find_compatible_node() is returning a pointer with
incremented refcount so it must be explicitly decremented after the
last use. As here it is only being used for checking of node presence
but the result is not actually used in the success path it can be
dropped immediately.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: commit f725758b89 ("KVM: PPC: Book3S HV: Use OPAL XICS emulation on POWER9")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When attaching a hardware table to LIOBN in KVM, we match table parameters
such as page size, table offset and table size. However the tables are
created via very different paths - VFIO and KVM - and the VFIO path goes
through the platform code which has minimum TCE page size requirement
(which is 4K but since we allocate memory by pages and cannot avoid
alignment anyway, we align to 64k pages for powernv_defconfig).
So when we match the tables, one might be bigger that the other which
means the hardware table cannot get attached to LIOBN and DMA mapping
fails.
This removes the table size alignment from the guest visible table.
This does not affect the memory allocation which is still aligned -
kvmppc_tce_pages() takes care of this.
This relaxes the check we do when attaching tables to allow the hardware
table be bigger than the guest visible table.
Ideally we want the KVM table to cover the same space as the hardware
table does but since the hardware table may use multiple levels, and
all levels must use the same table size (IODA2 design), the area it can
actually cover might get very different from the window size which
the guest requested, even though the guest won't map it all.
Fixes: ca1fc489cf "KVM: PPC: Book3S: Allow backing bigger guest IOMMU pages with smaller physical pages"
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Originally PPC KVM MMIO emulation uses only 0~31#(5 bits) for VSR
reg number, and use mmio_vsx_tx_sx_enabled field together for
0~63# VSR regs.
Currently PPC KVM MMIO emulation is reimplemented with analyse_instr()
assistance. analyse_instr() returns 0~63 for VSR register number, so
it is not necessary to use additional mmio_vsx_tx_sx_enabled field
any more.
This patch extends related reg bits (expand io_gpr to u16 from u8
and use 6 bits for VSR reg#), so that mmio_vsx_tx_sx_enabled can
be removed.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
At the moment we allocate the entire TCE table, twice (hardware part and
userspace translation cache). This normally works as we normally have
contigous memory and the guest will map entire RAM for 64bit DMA.
However if we have sparse RAM (one example is a memory device), then
we will allocate TCEs which will never be used as the guest only maps
actual memory for DMA. If it is a single level TCE table, there is nothing
we can really do but if it a multilevel table, we can skip allocating
TCEs we know we won't need.
This adds ability to allocate only first level, saving memory.
This changes iommu_table::free() to avoid allocating of an extra level;
iommu_table::set() will do this when needed.
This adds @alloc parameter to iommu_table::exchange() to tell the callback
if it can allocate an extra level; the flag is set to "false" for
the realmode KVM handlers of H_PUT_TCE hcalls and the callback returns
H_TOO_HARD.
This still requires the entire table to be counted in mm::locked_vm.
To be conservative, this only does on-demand allocation when
the usespace cache table is requested which is the case of VFIO.
The example math for a system replicating a powernv setup with NVLink2
in a guest:
16GB RAM mapped at 0x0
128GB GPU RAM window (16GB of actual RAM) mapped at 0x244000000000
the table to cover that all with 64K pages takes:
(((0x244000000000 + 0x2000000000) >> 16)*8)>>20 = 4556MB
If we allocate only necessary TCE levels, we will only need:
(((0x400000000 + 0x400000000) >> 16)*8)>>20 = 4MB (plus some for indirect
levels).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We want to support sparse memory and therefore huge chunks of DMA windows
do not need to be mapped. If a DMA window big enough to require 2 or more
indirect levels, and a DMA window is used to map all RAM (which is
a default case for 64bit window), we can actually save some memory by
not allocation TCE for regions which we are not going to map anyway.
The hardware tables alreary support indirect levels but we also keep
host-physical-to-userspace translation array which is allocated by
vmalloc() and is a flat array which might use quite some memory.
This converts it_userspace from vmalloc'ed array to a multi level table.
As the format becomes platform dependend, this replaces the direct access
to it_usespace with a iommu_table_ops::useraddrptr hook which returns
a pointer to the userspace copy of a TCE; future extension will return
NULL if the level was not allocated.
This should not change non-KVM handling of TCE tables and it_userspace
will not be allocated for non-KVM tables.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We are going to reuse multilevel TCE code for the userspace copy of
the TCE table and since it is big endian, let's make the copy big endian
too.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 DD1 was never a product. It is no longer supported by upstream
firmware, and it is not effectively supported in Linux due to lack of
testing.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au>
[mpe: Remove arch_make_huge_pte() entirely]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Additional struct_size() conversions (Matthew, Kees)
- Explicitly reported overflow fixes (Silvio, Kees)
- Add missing kvcalloc() function (Kees)
- Treewide conversions of allocators to use either 2-factor argument
variant when available, or array_size() and array3_size() as needed (Kees)
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=zUUp
-----END PGP SIGNATURE-----
Merge tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull more overflow updates from Kees Cook:
"The rest of the overflow changes for v4.18-rc1.
This includes the explicit overflow fixes from Silvio, further
struct_size() conversions from Matthew, and a bug fix from Dan.
But the bulk of it is the treewide conversions to use either the
2-factor argument allocators (e.g. kmalloc(a * b, ...) into
kmalloc_array(a, b, ...) or the array_size() macros (e.g. vmalloc(a *
b) into vmalloc(array_size(a, b)).
Coccinelle was fighting me on several fronts, so I've done a bunch of
manual whitespace updates in the patches as well.
Summary:
- Error path bug fix for overflow tests (Dan)
- Additional struct_size() conversions (Matthew, Kees)
- Explicitly reported overflow fixes (Silvio, Kees)
- Add missing kvcalloc() function (Kees)
- Treewide conversions of allocators to use either 2-factor argument
variant when available, or array_size() and array3_size() as needed
(Kees)"
* tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (26 commits)
treewide: Use array_size in f2fs_kvzalloc()
treewide: Use array_size() in f2fs_kzalloc()
treewide: Use array_size() in f2fs_kmalloc()
treewide: Use array_size() in sock_kmalloc()
treewide: Use array_size() in kvzalloc_node()
treewide: Use array_size() in vzalloc_node()
treewide: Use array_size() in vzalloc()
treewide: Use array_size() in vmalloc()
treewide: devm_kzalloc() -> devm_kcalloc()
treewide: devm_kmalloc() -> devm_kmalloc_array()
treewide: kvzalloc() -> kvcalloc()
treewide: kvmalloc() -> kvmalloc_array()
treewide: kzalloc_node() -> kcalloc_node()
treewide: kzalloc() -> kcalloc()
treewide: kmalloc() -> kmalloc_array()
mm: Introduce kvcalloc()
video: uvesafb: Fix integer overflow in allocation
UBIFS: Fix potential integer overflow in allocation
leds: Use struct_size() in allocation
Convert intel uncore to struct_size
...
tabort. will perform transaction failure recording and the recording
depends on TEXASR FS bit. Currently the TEXASR FS bit is retrieved
after tabort., when the TEXASR FS bit is already been updated by
tabort. itself.
This patch corrects this behavior by retrieving TEXASR val before
tabort.
tabort. will not immediately leads to transaction failure handling
in suspend state. So this patch also remove the mtspr on TEXASR/TFIAR
registers to avoid TM bad thing exception.
Fixes: 26798f88d5 ("KVM: PPC: Book3S PR: Add emulation for tabort. in privileged state")
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
It turns out that PR KVM has no dependency on the format of HPTEs,
because it uses functions pointed to by mmu_hash_ops which do all
the formatting and interpretation of HPTEs. Thus we can allow PR
KVM to load on POWER9 bare-metal hosts as long as they are running
in HPT mode.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
PAPR guests run in supervisor mode and should not be able to set the
MSR HV (hypervisor mode) bit or clear the ME (machine check enable)
bit by mtmsrd or any other means. To enforce this, we force MSR_HV
off and MSR_ME on in kvmppc_set_msr_pr. Without this, the guest
can appear to be in hypervisor mode to itself and to userspace.
This has been observed to cause a crash in QEMU when it tries to
deliver a system reset interrupt to the guest.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The treclaim. emulation needs to record failure status in the TEXASR
register if the transaction had not previously failed. However, the
current code first does kvmppc_save_tm_pr() (which does a treclaim.
itself) and then checks the failure summary bit in TEXASR after that.
Since treclaim. itself causes transaction failure, the FS bit is
always set, so we were never updating TEXASR with the failure cause
supplied by the guest as the RA parameter to the treclaim. instruction.
This caused the tm-unavailable test in tools/testing/selftests/powerpc/tm
to fail.
To fix this, we need to read TEXASR before calling kvmppc_save_tm_pr(),
and base the final value of TEXASR on that value.
Fixes: 03c81682a9 ("KVM: PPC: Book3S PR: Add emulation for treclaim.")
Reviewed-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This makes sure that MSR "partial-function" bits are not transferred
to SRR1 when delivering an interrupt. This was causing failures in
guests running kernels that include commit f3d96e698e ("powerpc/mm:
Overhaul handling of bad page faults", 2017-07-19), which added code
to check bits of SRR1 on instruction storage interrupts (ISIs) that
indicate a bad page fault. The symptom was that a guest user program
that handled a signal and attempted to return from the signal handler
would get a SIGBUS signal and die.
The code that generated ISIs and some other interrupts would
previously set bits in the guest MSR to indicate the interrupt status
and then call kvmppc_book3s_queue_irqprio(). This technique no
longer works now that kvmppc_inject_interrupt() is masking off those
bits. Instead we make kvmppc_core_queue_data_storage() and
kvmppc_core_queue_inst_storage() call kvmppc_inject_interrupt()
directly, and make sure that all the places that generate ISIs or
DSIs call kvmppc_core_queue_{data,inst}_storage instead of
kvmppc_book3s_queue_irqprio().
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds trivial handling for additional interrupt types that KVM-PR must
support for proper virtualization on a POWER9 host in HPT mode, as a further
prerequisite to enabling KVM-PR on that configuration.
Signed-off-by: Cameron Kaiser <spectre@floodgap.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
* ARM: lazy context-switching of FPSIMD registers on arm64, "split"
regions for vGIC redistributor
* s390: cleanups for nested, clock handling, crypto, storage keys and
control register bits
* x86: many bugfixes, implement more Hyper-V super powers,
implement lapic_timer_advance_ns even when the LAPIC timer
is emulated using the processor's VMX preemption timer. Two
security-related bugfixes at the top of the branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJbH8Z/AAoJEL/70l94x66DF+UIAJeOuTp6LGasT/9uAb2OovaN
+5kGmOPGFwkTcmg8BQHI2fXT4vhxMXWPFcQnyig9eXJVxhuwluXDOH4P9IMay0yw
VDCBsWRdMvZDQad2hn6Z5zR4Jx01XrSaG/KqvXbbDKDCy96mWG7SYAY2m3ZwmeQi
3Pa3O3BTijr7hBYnMhdXGkSn4ZyU8uPaAgIJ8795YKeOJ2JmioGYk6fj6y2WCxA3
ztJymBjTmIoZ/F8bjuVouIyP64xH4q9roAyw4rpu7vnbWGqx1fjPYJoB8yddluWF
JqCPsPzhKDO7mjZJy+lfaxIlzz2BN7tKBNCm88s5GefGXgZwk3ByAq/0GQ2M3rk=
=H5zI
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"Small update for KVM:
ARM:
- lazy context-switching of FPSIMD registers on arm64
- "split" regions for vGIC redistributor
s390:
- cleanups for nested
- clock handling
- crypto
- storage keys
- control register bits
x86:
- many bugfixes
- implement more Hyper-V super powers
- implement lapic_timer_advance_ns even when the LAPIC timer is
emulated using the processor's VMX preemption timer.
- two security-related bugfixes at the top of the branch"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (79 commits)
kvm: fix typo in flag name
kvm: x86: use correct privilege level for sgdt/sidt/fxsave/fxrstor access
KVM: x86: pass kvm_vcpu to kvm_read_guest_virt and kvm_write_guest_virt_system
KVM: x86: introduce linear_{read,write}_system
kvm: nVMX: Enforce cpl=0 for VMX instructions
kvm: nVMX: Add support for "VMWRITE to any supported field"
kvm: nVMX: Restrict VMX capability MSR changes
KVM: VMX: Optimize tscdeadline timer latency
KVM: docs: nVMX: Remove known limitations as they do not exist now
KVM: docs: mmu: KVM support exposing SLAT to guests
kvm: no need to check return value of debugfs_create functions
kvm: Make VM ioctl do valloc for some archs
kvm: Change return type to vm_fault_t
KVM: docs: mmu: Fix link to NPT presentation from KVM Forum 2008
kvm: x86: Amend the KVM_GET_SUPPORTED_CPUID API documentation
KVM: x86: hyperv: declare KVM_CAP_HYPERV_TLBFLUSH capability
KVM: x86: hyperv: simplistic HVCALL_FLUSH_VIRTUAL_ADDRESS_{LIST,SPACE}_EX implementation
KVM: x86: hyperv: simplistic HVCALL_FLUSH_VIRTUAL_ADDRESS_{LIST,SPACE} implementation
KVM: introduce kvm_make_vcpus_request_mask() API
KVM: x86: hyperv: do rep check for each hypercall separately
...
Notable changes:
- Support for split PMD page table lock on 64-bit Book3S (Power8/9).
- Add support for HAVE_RELIABLE_STACKTRACE, so we properly support live
patching again.
- Add support for patching barrier_nospec in copy_from_user() and syscall entry.
- A couple of fixes for our data breakpoints on Book3S.
- A series from Nick optimising TLB/mm handling with the Radix MMU.
- Numerous small cleanups to squash sparse/gcc warnings from Mathieu Malaterre.
- Several series optimising various parts of the 32-bit code from Christophe Leroy.
- Removal of support for two old machines, "SBC834xE" and "C2K" ("GEFanuc,C2K"),
which is why the diffstat has so many deletions.
And many other small improvements & fixes.
There's a few out-of-area changes. Some minor ftrace changes OK'ed by Steve, and
a fix to our powernv cpuidle driver. Then there's a series touching mm, x86 and
fs/proc/task_mmu.c, which cleans up some details around pkey support. It was
ack'ed/reviewed by Ingo & Dave and has been in next for several weeks.
Thanks to:
Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Al Viro, Andrew
Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Arnd Bergmann, Balbir Singh,
Cédric Le Goater, Christophe Leroy, Christophe Lombard, Colin Ian King, Dave
Hansen, Fabio Estevam, Finn Thain, Frederic Barrat, Gautham R. Shenoy, Haren
Myneni, Hari Bathini, Ingo Molnar, Jonathan Neuschäfer, Josh Poimboeuf,
Kamalesh Babulal, Madhavan Srinivasan, Mahesh Salgaonkar, Mark Greer, Mathieu
Malaterre, Matthew Wilcox, Michael Neuling, Michal Suchanek, Naveen N. Rao,
Nicholas Piggin, Nicolai Stange, Olof Johansson, Paul Gortmaker, Paul
Mackerras, Peter Rosin, Pridhiviraj Paidipeddi, Ram Pai, Rashmica Gupta, Ravi
Bangoria, Russell Currey, Sam Bobroff, Samuel Mendoza-Jonas, Segher
Boessenkool, Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stewart Smith,
Thiago Jung Bauermann, Torsten Duwe, Vaibhav Jain, Wei Yongjun, Wolfram Sang,
Yisheng Xie, YueHaibing.
-----BEGIN PGP SIGNATURE-----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=ZlBf
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- Support for split PMD page table lock on 64-bit Book3S (Power8/9).
- Add support for HAVE_RELIABLE_STACKTRACE, so we properly support
live patching again.
- Add support for patching barrier_nospec in copy_from_user() and
syscall entry.
- A couple of fixes for our data breakpoints on Book3S.
- A series from Nick optimising TLB/mm handling with the Radix MMU.
- Numerous small cleanups to squash sparse/gcc warnings from Mathieu
Malaterre.
- Several series optimising various parts of the 32-bit code from
Christophe Leroy.
- Removal of support for two old machines, "SBC834xE" and "C2K"
("GEFanuc,C2K"), which is why the diffstat has so many deletions.
And many other small improvements & fixes.
There's a few out-of-area changes. Some minor ftrace changes OK'ed by
Steve, and a fix to our powernv cpuidle driver. Then there's a series
touching mm, x86 and fs/proc/task_mmu.c, which cleans up some details
around pkey support. It was ack'ed/reviewed by Ingo & Dave and has
been in next for several weeks.
Thanks to: Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Al
Viro, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Arnd
Bergmann, Balbir Singh, Cédric Le Goater, Christophe Leroy, Christophe
Lombard, Colin Ian King, Dave Hansen, Fabio Estevam, Finn Thain,
Frederic Barrat, Gautham R. Shenoy, Haren Myneni, Hari Bathini, Ingo
Molnar, Jonathan Neuschäfer, Josh Poimboeuf, Kamalesh Babulal,
Madhavan Srinivasan, Mahesh Salgaonkar, Mark Greer, Mathieu Malaterre,
Matthew Wilcox, Michael Neuling, Michal Suchanek, Naveen N. Rao,
Nicholas Piggin, Nicolai Stange, Olof Johansson, Paul Gortmaker, Paul
Mackerras, Peter Rosin, Pridhiviraj Paidipeddi, Ram Pai, Rashmica
Gupta, Ravi Bangoria, Russell Currey, Sam Bobroff, Samuel
Mendoza-Jonas, Segher Boessenkool, Shilpasri G Bhat, Simon Guo,
Souptick Joarder, Stewart Smith, Thiago Jung Bauermann, Torsten Duwe,
Vaibhav Jain, Wei Yongjun, Wolfram Sang, Yisheng Xie, YueHaibing"
* tag 'powerpc-4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (251 commits)
powerpc/64s/radix: Fix missing ptesync in flush_cache_vmap
cpuidle: powernv: Fix promotion from snooze if next state disabled
powerpc: fix build failure by disabling attribute-alias warning in pci_32
ocxl: Fix missing unlock on error in afu_ioctl_enable_p9_wait()
powerpc-opal: fix spelling mistake "Uniterrupted" -> "Uninterrupted"
powerpc: fix spelling mistake: "Usupported" -> "Unsupported"
powerpc/pkeys: Detach execute_only key on !PROT_EXEC
powerpc/powernv: copy/paste - Mask SO bit in CR
powerpc: Remove core support for Marvell mv64x60 hostbridges
powerpc/boot: Remove core support for Marvell mv64x60 hostbridges
powerpc/boot: Remove support for Marvell mv64x60 i2c controller
powerpc/boot: Remove support for Marvell MPSC serial controller
powerpc/embedded6xx: Remove C2K board support
powerpc/lib: optimise PPC32 memcmp
powerpc/lib: optimise 32 bits __clear_user()
powerpc/time: inline arch_vtime_task_switch()
powerpc/Makefile: set -mcpu=860 flag for the 8xx
powerpc: Implement csum_ipv6_magic in assembly
powerpc/32: Optimise __csum_partial()
powerpc/lib: Adjust .balign inside string functions for PPC32
...
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
This cleans up the error handling a lot, as this code will never get
hit.
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Christoffer Dall <christoffer.dall@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim KrÄmář" <rkrcmar@redhat.com>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Eric Auger <eric.auger@redhat.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: kvm-ppc@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: kvmarm@lists.cs.columbia.edu
Cc: kvm@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use new return type vm_fault_t for fault handler. For
now, this is just documenting that the function returns
a VM_FAULT value rather than an errno. Once all instances
are converted, vm_fault_t will become a distinct type.
commit 1c8f422059 ("mm: change return type to vm_fault_t")
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We need to migrate PR KVM during transaction and userspace will use
kvmppc_get_one_reg_pr()/kvmppc_set_one_reg_pr() APIs to get/set
transaction checkpoint state. This patch adds support for that.
So far, QEMU on PR KVM doesn't fully function for migration but the
savevm/loadvm can be done against a RHEL72 guest. During savevm/
loadvm procedure, the kvm ioctls will be invoked as well.
Test has been performed to savevm/loadvm for a guest running
a HTM test program:
https://github.com/justdoitqd/publicFiles/blob/master/test-tm-mig.c
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
In both HV and PR KVM, the KVM_SET_REGS/KVM_GET_REGS ioctl should
be able to perform without the vcpu loaded.
Since the vcpu mutex locking/unlock has been moved out of vcpu_load()
/vcpu_put(), KVM_SET_REGS/KVM_GET_REGS don't need to do ioctl with
the vcpu loaded anymore. This patch removes vcpu_load()/vcpu_put()
from KVM_SET_REGS/KVM_GET_REGS ioctl.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Since the vcpu mutex locking/unlock has been moved out of vcpu_load()
/vcpu_put(), KVM_GET_ONE_REG and KVM_SET_ONE_REG doesn't need to do
ioctl with loading vcpu anymore. This patch removes vcpu_load()/vcpu_put()
from KVM_GET_ONE_REG and KVM_SET_ONE_REG ioctl.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Although we already have kvm_arch_vcpu_async_ioctl() which doesn't require
ioctl to load vcpu, the sync ioctl code need to be cleaned up when
CONFIG_HAVE_KVM_VCPU_ASYNC_IOCTL is not configured.
This patch moves vcpu_load/vcpu_put down to each ioctl switch case so that
each ioctl can decide to do vcpu_load/vcpu_put or not independently.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently guest kernel doesn't handle TAR facility unavailable and it
always runs with TAR bit on. PR KVM will lazily enable TAR. TAR is not
a frequent-use register and it is not included in SVCPU struct.
Due to the above, the checkpointed TAR val might be a bogus TAR val.
To solve this issue, we will make vcpu->arch.fscr tar bit consistent
with shadow_fscr when TM is enabled.
At the end of emulating treclaim., the correct TAR val need to be loaded
into the register if FSCR_TAR bit is on.
At the beginning of emulating trechkpt., TAR needs to be flushed so that
the right tar val can be copied into tar_tm.
Tested with:
tools/testing/selftests/powerpc/tm/tm-tar
tools/testing/selftests/powerpc/ptrace/ptrace-tm-tar (remove DSCR/PPR
related testing).
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently PR KVM doesn't support transaction memory in guest privileged
state.
This patch adds a check at setting guest msr, so that we can never return
to guest with PR=0 and TS=0b10. A tabort will be emulated to indicate
this and fail transaction immediately.
[paulus@ozlabs.org - don't change the TM_CAUSE_MISC definition, instead
use TM_CAUSE_KVM_FAC_UNAV.]
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently privileged-state guest will be run with TM disabled.
Although the privileged-state guest cannot initiate a new transaction,
it can use tabort to terminate its problem state's transaction.
So it is still necessary to emulate tabort. for privileged-state guest.
Tested with:
https://github.com/justdoitqd/publicFiles/blob/master/test_tabort.c
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This patch adds host emulation when guest PR KVM executes "trechkpt.",
which is a privileged instruction and will trap into host.
We firstly copy vcpu ongoing content into vcpu tm checkpoint
content, then perform kvmppc_restore_tm_pr() to do trechkpt.
with updated vcpu tm checkpoint values.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This patch adds support for "treclaim." emulation when PR KVM guest
executes treclaim. and traps to host.
We will firstly do treclaim. and save TM checkpoint. Then it is
necessary to update vcpu current reg content with checkpointed vals.
When rfid into guest again, those vcpu current reg content (now the
checkpoint vals) will be loaded into regs.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently kvmppc_handle_fac() will not update NV GPRs and thus it can
return with GUEST_RESUME.
However PR KVM guest always disables MSR_TM bit in privileged state.
If PR privileged-state guest is trying to read TM SPRs, it will
trigger TM facility unavailable exception and fall into
kvmppc_handle_fac(). Then the emulation will be done by
kvmppc_core_emulate_mfspr_pr(). The mfspr instruction can include a
RT with NV reg. So it is necessary to restore NV GPRs at this case, to
reflect the update to NV RT.
This patch make kvmppc_handle_fac() return GUEST_RESUME_NV for TM
facility unavailable exceptions in guest privileged state.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently the kernel doesn't use transaction memory.
And there is an issue for privileged state in the guest that:
tbegin/tsuspend/tresume/tabort TM instructions can impact MSR TM bits
without trapping into the PR host. So following code will lead to a
false mfmsr result:
tbegin <- MSR bits update to Transaction active.
beq <- failover handler branch
mfmsr <- still read MSR bits from magic page with
transaction inactive.
It is not an issue for non-privileged guest state since its mfmsr is
not patched with magic page and will always trap into the PR host.
This patch will always fail tbegin attempt for privileged state in the
guest, so that the above issue is prevented. It is benign since
currently (guest) kernel doesn't initiate a transaction.
Test case:
https://github.com/justdoitqd/publicFiles/blob/master/test_tbegin_pr.c
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The mfspr/mtspr on TM SPRs(TEXASR/TFIAR/TFHAR) are non-privileged
instructions and can be executed by PR KVM guest in problem state
without trapping into the host. We only emulate mtspr/mfspr
texasr/tfiar/tfhar in guest PR=0 state.
When we are emulating mtspr tm sprs in guest PR=0 state, the emulation
result needs to be visible to guest PR=1 state. That is, the actual TM
SPR val should be loaded into actual registers.
We already flush TM SPRs into vcpu when switching out of CPU, and load
TM SPRs when switching back.
This patch corrects mfspr()/mtspr() emulation for TM SPRs to make the
actual source/dest be the actual TM SPRs.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The math registers will be saved into vcpu->arch.fp/vr and corresponding
vcpu->arch.fp_tm/vr_tm area.
We flush or giveup the math regs into vcpu->arch.fp/vr before saving
transaction. After transaction is restored, the math regs will be loaded
back into regs.
If there is a FP/VEC/VSX unavailable exception during transaction active
state, the math checkpoint content might be incorrect and we need to do
treclaim./load the correct checkpoint val/trechkpt. sequence to retry the
transaction. That will make our solution complicated. To solve this issue,
we always make the hardware guest MSR math bits (shadow_msr) consistent
with the MSR val which guest sees (kvmppc_get_msr()) when guest msr is
with tm enabled. Then all FP/VEC/VSX unavailable exception can be delivered
to guest and guest handles the exception by itself.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The transaction memory checkpoint area save/restore behavior is
triggered when VCPU qemu process is switching out/into CPU, i.e.
at kvmppc_core_vcpu_put_pr() and kvmppc_core_vcpu_load_pr().
MSR TM active state is determined by TS bits:
active: 10(transactional) or 01 (suspended)
inactive: 00 (non-transactional)
We don't "fake" TM functionality for guest. We "sync" guest virtual
MSR TM active state(10 or 01) with shadow MSR. That is to say,
we don't emulate a transactional guest with a TM inactive MSR.
TM SPR support(TFIAR/TFAR/TEXASR) has already been supported by
commit 9916d57e64 ("KVM: PPC: Book3S PR: Expose TM registers").
Math register support (FPR/VMX/VSX) will be done at subsequent
patch.
Whether TM context need to be saved/restored can be determined
by kvmppc_get_msr() TM active state:
* TM active - save/restore TM context
* TM inactive - no need to do so and only save/restore
TM SPRs.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Suggested-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This patch adds 2 new APIs, kvmppc_save_tm_sprs() and
kvmppc_restore_tm_sprs(), for the purpose of TEXASR/TFIAR/TFHAR
save/restore.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This patch adds 2 new APIs: kvmppc_copyto_vcpu_tm() and
kvmppc_copyfrom_vcpu_tm(). These 2 APIs will be used to copy from/to TM
data between VCPU_TM/VCPU area.
PR KVM will use these APIs for treclaim. or trechkpt. emulation.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
PR KVM host usually runs with TM enabled in its host MSR value, and
with non-transactional TS value.
When a guest with TM active traps into PR KVM host, the rfid at the
tail of kvmppc_interrupt_pr() will try to switch TS bits from
S0 (Suspended & TM disabled) to N1 (Non-transactional & TM enabled).
That will leads to TM Bad Thing interrupt.
This patch manually sets target TS bits unchanged to avoid this
exception.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
According to ISA specification for RFID, in MSR TM disabled and TS
suspended state (S0), if the target MSR is TM disabled and TS state is
inactive (N0), rfid should suppress this update.
This patch makes the RFID emulation of PR KVM consistent with this.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
MSR TS bits can be modified with non-privileged instruction such as
tbegin./tend. That means guest can change MSR value "silently" without
notifying host.
It is necessary to sync the TM bits to host so that host can calculate
shadow msr correctly.
Note, privileged mode in the guest will always fail transactions so we
only take care of problem state mode in the guest.
The logic is put into kvmppc_copy_from_svcpu() so that
kvmppc_handle_exit_pr() can use correct MSR TM bits even when preemption
occurs.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
PowerPC TM functionality needs MSR TM/TS bits support in hardware level.
Guest TM functionality can not be emulated with "fake" MSR (msr in magic
page) TS bits.
This patch syncs TM/TS bits in shadow_msr with the MSR value in magic
page, so that the MSR TS value which guest sees is consistent with actual
MSR bits running in guest.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This patch simulates interrupt behavior per Power ISA while injecting
interrupt in PR KVM:
- When interrupt happens, transactional state should be suspended.
kvmppc_mmu_book3s_64_reset_msr() will be invoked when injecting an
interrupt. This patch performs this ISA logic in
kvmppc_mmu_book3s_64_reset_msr().
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently __kvmppc_save/restore_tm() APIs can only be invoked from
assembly function. This patch adds C function wrappers for them so
that they can be safely called from C function.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
kvmppc_save_tm() invokes store_fp_state/store_vr_state(). So it is
mandatory to turn on FP/VSX/VMX MSR bits for its execution, just
like what kvmppc_restore_tm() did.
Previously HV KVM has turned the bits on outside of function
kvmppc_save_tm(). Now we include this bit change in kvmppc_save_tm()
so that the logic is cleaner. And PR KVM can reuse it later.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
HV KVM and PR KVM need different MSR source to indicate whether
treclaim. or trecheckpoint. is necessary.
This patch add new parameter (guest MSR) for these kvmppc_save_tm/
kvmppc_restore_tm() APIs:
- For HV KVM, it is VCPU_MSR
- For PR KVM, it is current host MSR or VCPU_SHADOW_SRR1
This enhancement enables these 2 APIs to be reused by PR KVM later.
And the patch keeps HV KVM logic unchanged.
This patch also reworks kvmppc_save_tm()/kvmppc_restore_tm() to
have a clean ABI: r3 for vcpu and r4 for guest_msr.
During kvmppc_save_tm/kvmppc_restore_tm(), the R1 need to be saved
or restored. Currently the R1 is saved into HSTATE_HOST_R1. In PR
KVM, we are going to add a C function wrapper for
kvmppc_save_tm/kvmppc_restore_tm() where the R1 will be incremented
with added stackframe and save into HSTATE_HOST_R1. There are several
places in HV KVM to load HSTATE_HOST_R1 as R1, and we don't want to
bring risk or confusion by TM code.
This patch will use HSTATE_SCRATCH2 to save/restore R1 in
kvmppc_save_tm/kvmppc_restore_tm() to avoid future confusion, since
the r1 is actually a temporary/scratch value to be saved/stored.
[paulus@ozlabs.org - rebased on top of 7b0e827c69 ("KVM: PPC: Book3S HV:
Factor fake-suspend handling out of kvmppc_save/restore_tm", 2018-05-30)]
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
It is a simple patch just for moving kvmppc_save_tm/kvmppc_restore_tm()
functionalities to tm.S. There is no logic change. The reconstruct of
those APIs will be done in later patches to improve readability.
It is for preparation of reusing those APIs on both HV/PR PPC KVM.
Some slight change during move the functions includes:
- surrounds some HV KVM specific code with CONFIG_KVM_BOOK3S_HV_POSSIBLE
for compilation.
- use _GLOBAL() to define kvmppc_save_tm/kvmppc_restore_tm()
[paulus@ozlabs.org - rebased on top of 7b0e827c69 ("KVM: PPC: Book3S HV:
Factor fake-suspend handling out of kvmppc_save/restore_tm", 2018-05-30)]
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This splits out the handling of "fake suspend" mode, part of the
hypervisor TM assist code for POWER9, and puts almost all of it in
new kvmppc_save_tm_hv and kvmppc_restore_tm_hv functions. The new
functions branch to kvmppc_save/restore_tm if the CPU does not
require hypervisor TM assistance.
With this, it will be more straightforward to move kvmppc_save_tm and
kvmppc_restore_tm to another file and use them for transactional
memory support in PR KVM. Additionally, it also makes the code a
bit clearer and reduces the number of feature sections.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently, PR KVM does not implement the configure_mmu operation, and
so the KVM_PPC_CONFIGURE_V3_MMU ioctl always fails with an EINVAL
error. This causes recent kernels to fail to boot as a PR KVM guest
on POWER9, since recent kernels booted in HPT mode do the
H_REGISTER_PROC_TBL hypercall, which causes userspace (QEMU) to do
KVM_PPC_CONFIGURE_V3_MMU, which fails.
This implements a minimal configure_mmu operation for PR KVM. It
succeeds only if the MMU is being configured for HPT mode and no
process table is being registered. This is enough to get recent
kernels to boot as a PR KVM guest.
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This patch reimplements LOAD_VMX/STORE_VMX MMIO emulation with
analyse_instr() input. When emulating the store, the VMX reg will need to
be flushed so that the right reg val can be retrieved before writing to
IO MEM.
This patch also adds support for lvebx/lvehx/lvewx/stvebx/stvehx/stvewx
MMIO emulation. To meet the requirement of handling different element
sizes, kvmppc_handle_load128_by2x64()/kvmppc_handle_store128_by2x64()
were replaced with kvmppc_handle_vmx_load()/kvmppc_handle_vmx_store().
The framework used is similar to VSX instruction MMIO emulation.
Suggested-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
VSX MMIO emulation uses mmio_vsx_copy_type to represent VSX emulated
element size/type, such as KVMPPC_VSX_COPY_DWORD_LOAD, etc. This
patch expands mmio_vsx_copy_type to cover VMX copy type, such as
KVMPPC_VMX_COPY_BYTE(stvebx/lvebx), etc. As a result,
mmio_vsx_copy_type is also renamed to mmio_copy_type.
It is a preparation for reimplementing VMX MMIO emulation.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This patch reimplements LOAD_VSX/STORE_VSX instruction MMIO emulation with
analyse_instr() input. It utilizes VSX_FPCONV/VSX_SPLAT/SIGNEXT exported
by analyse_instr() and handle accordingly.
When emulating VSX store, the VSX reg will need to be flushed so that
the right reg val can be retrieved before writing to IO MEM.
[paulus@ozlabs.org - mask the register number to 5 bits.]
Suggested-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This patch reimplements LOAD_FP/STORE_FP instruction MMIO emulation with
analyse_instr() input. It utilizes the FPCONV/UPDATE properties exported by
analyse_instr() and invokes kvmppc_handle_load(s)/kvmppc_handle_store()
accordingly.
For FP store MMIO emulation, the FP regs need to be flushed firstly so
that the right FP reg vals can be read from vcpu->arch.fpr, which will
be stored into MMIO data.
Suggested-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently HV will save math regs(FP/VEC/VSX) when trap into host. But
PR KVM will only save math regs when qemu task switch out of CPU, or
when returning from qemu code.
To emulate FP/VEC/VSX mmio load, PR KVM need to make sure that math
regs were flushed firstly and then be able to update saved VCPU
FPR/VEC/VSX area reasonably.
This patch adds giveup_ext() field to KVM ops. Only PR KVM has non-NULL
giveup_ext() ops. kvmppc_complete_mmio_load() can invoke that hook
(when not NULL) to flush math regs accordingly, before updating saved
register vals.
Math regs flush is also necessary for STORE, which will be covered
in later patch within this patch series.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This patch reimplements non-SIMD LOAD/STORE instruction MMIO emulation
with analyse_instr() input. It utilizes the BYTEREV/UPDATE/SIGNEXT
properties exported by analyse_instr() and invokes
kvmppc_handle_load(s)/kvmppc_handle_store() accordingly.
It also moves CACHEOP type handling into the skeleton.
instruction_type within kvm_ppc.h is renamed to avoid conflict with
sstep.h.
Suggested-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Some VSX instructions like lxvwsx will splat word into VSR. This patch
adds a new VSX copy type KVMPPC_VSX_COPY_WORD_LOAD_DUMP to support this.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This relaxes the restriction on using PR KVM on POWER9. The existing
code does work inside a guest partition running in HPT mode, because
hypercalls such as H_ENTER use the old HPTE format, not the new
format used by POWER9, and so no change to PR KVM's HPT manipulation
code is required. PR KVM will still refuse to run if the kernel is
using radix translation or if it is running bare-metal.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
It's possible to take a SRESET or MCE in these paths due to a bug
in the host code or a NMI IPI, etc. A recent bug attempting to load
a virtual address from real mode gave th complete but cryptic error,
abridged:
Oops: Bad interrupt in KVM entry/exit code, sig: 6 [#1]
LE SMP NR_CPUS=2048 NUMA PowerNV
CPU: 53 PID: 6582 Comm: qemu-system-ppc Not tainted
NIP: c0000000000155ac LR: c0000000000c2430 CTR: c000000000015580
REGS: c000000fff76dd80 TRAP: 0200 Not tainted
MSR: 9000000000201003 <SF,HV,ME,RI,LE> CR: 48082222 XER: 00000000
CFAR: 0000000102900ef0 DAR: d00017fffd941a28 DSISR: 00000040 SOFTE: 3
NIP [c0000000000155ac] perf_trace_tlbie+0x2c/0x1a0
LR [c0000000000c2430] do_tlbies+0x230/0x2f0
Sending the NMIs through the Linux handlers gives a nicer output:
Severe Machine check interrupt [Not recovered]
NIP [c0000000000155ac]: perf_trace_tlbie+0x2c/0x1a0
Initiator: CPU
Error type: Real address [Load (bad)]
Effective address: d00017fffcc01a28
opal: Machine check interrupt unrecoverable: MSR(RI=0)
opal: Hardware platform error: Unrecoverable Machine Check exception
CPU: 0 PID: 6700 Comm: qemu-system-ppc Tainted: G M
NIP: c0000000000155ac LR: c0000000000c23c0 CTR: c000000000015580
REGS: c000000fff9e9d80 TRAP: 0200 Tainted: G M
MSR: 9000000000201001 <SF,HV,ME,LE> CR: 48082222 XER: 00000000
CFAR: 000000010cbc1a30 DAR: d00017fffcc01a28 DSISR: 00000040 SOFTE: 3
NIP [c0000000000155ac] perf_trace_tlbie+0x2c/0x1a0
LR [c0000000000c23c0] do_tlbies+0x1c0/0x280
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When CONFIG_RELOCATABLE=n, the Linux real mode interrupt handlers call
into KVM using real address. This needs to be translated to the kernel
linear effective address before the MMU is switched on.
kvmppc_bad_host_intr misses adding these bits, so when it is used to
handle a system reset interrupt (that always gets delivered in real
mode), it results in an instruction access fault immediately after
the MMU is turned on.
Fix this by ensuring the top 2 address bits are set when the MMU is
turned on.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Adding the write bit and RC bits to pte permissions does not require a
pte clear and flush. There should not be other bits changed here,
because restricting access or changing the PFN must have already
invalidated any existing ptes (otherwise the race is already lost).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When the radix fault handler has no page from the process address
space (e.g., for IO memory), it looks up the process pte and sets
partition table pte using that to get attributes like CI and guarded.
If the process table entry is to be writable, set _PAGE_DIRTY as well
to avoid an RC update. If not, then ensure _PAGE_DIRTY does not come
across. Set _PAGE_ACCESSED as well to avoid RC update.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The radix guest code can has fewer restrictions about what context it
can run in, so move this flushing out of assembly and have it use the
Linux TLB flush implementations introduced previously.
This allows powerpc:tlbie trace events to be used.
This changes the tlbiel sequence to only execute RIC=2 flush once on
the first set flushed, then RIC=0 for the rest of the sets. The end
result of the flush should be unchanged. This matches the local PID
flush pattern that was introduced in a5998fcb92 ("powerpc/mm/radix:
Optimise tlbiel flush all case").
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This has the advantage of consolidating TLB flush code in fewer
places, and it also implements powerpc:tlbie trace events.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When partition scope mappings are unmapped with kvm_unmap_radix, the
pte is cleared, but the page table structure is left in place. If the
next page fault requests a different page table geometry (e.g., due to
THP promotion or split), kvmppc_create_pte is responsible for changing
the page tables.
When a page table entry is to be converted to a large pte, the page
table entry is cleared, the PWC flushed, then the page table it points
to freed. This will cause pte page tables to leak when a 1GB page is
to replace a pud entry points to a pmd table with pte tables under it:
The pmd table will be freed, but its pte tables will be missed.
Fix this by replacing the simple clear and free code with one that
walks down the page tables and frees children. Care must be taken to
clear the root entry being unmapped then flushing the PWC before
freeing any page tables, as explained in comments.
This requires PWC flush to logically become a flush-all-PWC (which it
already is in hardware, but the KVM API needs to be changed to avoid
confusion).
This code also checks that no unexpected pte entries exist in any page
table being freed, and unmaps those and emits a WARN. This is an
expensive operation for the pte page level, but partition scope
changes are rare, so it's unconditional for now to iron out bugs. It
can be put under a CONFIG option or removed after some time.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
tlbies to an LPAR do not have to be serialised since POWER4/PPC970,
after which the MMU_FTR_LOCKLESS_TLBIE feature was introduced to
avoid tlbie locking.
Since commit c17b98cf60 ("KVM: PPC: Book3S HV: Remove code for
PPC970 processors"), KVM no longer supports processors that do not
have this feature, so the tlbie locking can be removed completely.
A sanity check for the feature is put in kvmppc_mmu_hv_init.
Testing was done on a POWER9 system in HPT mode, with a -smp 32 guest
in HPT mode. 32 instances of the powerpc fork benchmark from selftests
were run with --fork, and the results measured.
Without this patch, total throughput was about 13.5K/sec, and this is
the top of the host profile:
74.52% [k] do_tlbies
2.95% [k] kvmppc_book3s_hv_page_fault
1.80% [k] calc_checksum
1.80% [k] kvmppc_vcpu_run_hv
1.49% [k] kvmppc_run_core
After this patch, throughput was about 51K/sec, with this profile:
21.28% [k] do_tlbies
5.26% [k] kvmppc_run_core
4.88% [k] kvmppc_book3s_hv_page_fault
3.30% [k] _raw_spin_lock_irqsave
3.25% [k] gup_pgd_range
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When KVM emulates VMX store, it will invoke kvmppc_get_vmx_data() to
retrieve VMX reg val. kvmppc_get_vmx_data() will check mmio_host_swabbed
to decide which double word of vr[] to be used. But the
mmio_host_swabbed can be uninitialized during VMX store procedure:
kvmppc_emulate_loadstore
\- kvmppc_handle_store128_by2x64
\- kvmppc_get_vmx_data
So vcpu->arch.mmio_host_swabbed is not meant to be used at all for
emulation of store instructions, and this patch makes that true for
VMX stores. This patch also initializes mmio_host_swabbed to avoid
possible future problems.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This patch moves nip/ctr/lr/xer registers from scattered places in
kvm_vcpu_arch to pt_regs structure.
cr register is "unsigned long" in pt_regs and u32 in vcpu->arch.
It will need more consideration and may move in later patches.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Current regs are scattered at kvm_vcpu_arch structure and it will
be more neat to organize them into pt_regs structure.
Also it will enable reimplementation of MMIO emulation code with
analyse_instr() later.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This merges in the ppc-kvm topic branch of the powerpc repository
to get some changes on which future patches will depend, in particular
the definitions of various new TLB flushing functions.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Use new return type vm_fault_t for fault handler
in struct vm_operations_struct. For now, this is
just documenting that the function returns a
VM_FAULT value rather than an errno. Once all
instances are converted, vm_fault_t will become
a distinct type.
commit 1c8f422059 ("mm: change return type to
vm_fault_t")
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Although it does not seem possible to break the host by passing bad
parameters when creating a TCE table in KVM, it is still better to get
an early clear indication of that than debugging weird effect this might
bring.
This adds some sanity checks that the page size is 4KB..16GB as this is
what the actual LoPAPR supports and that the window actually fits 64bit
space.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
At the moment we only support in the host the IOMMU page sizes which
the guest is aware of, which is 4KB/64KB/16MB. However P9 does not support
16MB IOMMU pages, 2MB and 1GB pages are supported instead. We can still
emulate bigger guest pages (for example 16MB) with smaller host pages
(4KB/64KB/2MB).
This allows the physical IOMMU pages to use a page size smaller or equal
than the guest visible IOMMU page size.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The other TCE handlers use page shift from the guest visible TCE table
(described by kvmppc_spapr_tce_iommu_table) so let's make H_STUFF_TCE
handlers do the same thing.
This should cause no behavioral change now but soon we will allow
the iommu_table::it_page_shift being different from from the emulated
table page size so this will play a role.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
We now have interrupts hard-disabled when coming back from
kvmppc_hv_entry_trampoline, so this changes the comment to reflect
that.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Although Linux doesn't use PURR and SPURR ((Scaled) Processor
Utilization of Resources Register), other OSes depend on them.
On POWER8 they count at a rate depending on whether the VCPU is
idle or running, the activity of the VCPU, and the value in the
RWMR (Region-Weighting Mode Register). Hardware expects the
hypervisor to update the RWMR when a core is dispatched to reflect
the number of online VCPUs in the vcore.
This adds code to maintain a count in the vcore struct indicating
how many VCPUs are online. In kvmppc_run_core we use that count
to set the RWMR register on POWER8. If the core is split because
of a static or dynamic micro-threading mode, we use the value for
8 threads. The RWMR value is not relevant when the host is
executing because Linux does not use the PURR or SPURR register,
so we don't bother saving and restoring the host value.
For the sake of old userspace which does not set the KVM_REG_PPC_ONLINE
register, we set online to 1 if it was 0 at the time of a KVM_RUN
ioctl.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds a new KVM_REG_PPC_ONLINE register which userspace can set
to 0 or 1 via the GET/SET_ONE_REG interface to indicate whether it
considers the VCPU to be offline (0), that is, not currently running,
or online (1). This will be used in a later patch to configure the
register which controls PURR and SPURR accumulation.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
A radix guest can execute tlbie instructions to invalidate TLB entries.
After a tlbie or a group of tlbies, it must then do the architected
sequence eieio; tlbsync; ptesync to ensure that the TLB invalidation
has been processed by all CPUs in the system before it can rely on
no CPU using any translation that it just invalidated.
In fact it is the ptesync which does the actual synchronization in
this sequence, and hardware has a requirement that the ptesync must
be executed on the same CPU thread as the tlbies which it is expected
to order. Thus, if a vCPU gets moved from one physical CPU to
another after it has done some tlbies but before it can get to do the
ptesync, the ptesync will not have the desired effect when it is
executed on the second physical CPU.
To fix this, we do a ptesync in the exit path for radix guests. If
there are any pending tlbies, this will wait for them to complete.
If there aren't, then ptesync will just do the same as sync.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When a vcpu priority (CPPR) is set to a lower value (masking more
interrupts), we stop processing interrupts already in the queue
for the priorities that have now been masked.
If those interrupts were previously re-routed to a different
CPU, they might still be stuck until the older one that has
them in its queue processes them. In the case of guest CPU
unplug, that can be never.
To address that without creating additional overhead for
the normal interrupt processing path, this changes H_CPPR
handling so that when such a priority change occurs, we
scan the interrupt queue for that vCPU, and for any
interrupt in there that has been re-routed, we replace it
with a dummy and force a re-trigger.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The current partition table unmap code clears the _PAGE_PRESENT bit
out of the pte, which leaves pud_huge/pmd_huge true and does not
clear pud_present/pmd_present. This can confuse subsequent page
faults and possibly lead to the guest looping doing continual
hypervisor page faults.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The standard eieio ; tlbsync ; ptesync must follow tlbie to ensure it
is ordered with respect to subsequent operations.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently, the HV KVM guest entry/exit code adds the timebase offset
from the vcore struct to the timebase on guest entry, and subtracts
it on guest exit. Which is fine, except that it is possible for
userspace to change the offset using the SET_ONE_REG interface while
the vcore is running, as there is only one timebase offset per vcore
but potentially multiple VCPUs in the vcore. If that were to happen,
KVM would subtract a different offset on guest exit from that which
it had added on guest entry, leading to the timebase being out of sync
between cores in the host, which then leads to bad things happening
such as hangs and spurious watchdog timeouts.
To fix this, we add a new field 'tb_offset_applied' to the vcore struct
which stores the offset that is currently applied to the timebase.
This value is set from the vcore tb_offset field on guest entry, and
is what is subtracted from the timebase on guest exit. Since it is
zero when the timebase offset is not applied, we can simplify the
logic in kvmhv_start_timing and kvmhv_accumulate_time.
In addition, we had secondary threads reading the timebase while
running concurrently with code on the primary thread which would
eventually add or subtract the timebase offset from the timebase.
This occurred while saving or restoring the DEC register value on
the secondary threads. Although no specific incorrect behaviour has
been observed, this is a race which should be fixed. To fix it, we
move the DEC saving code to just before we call kvmhv_commence_exit,
and the DEC restoring code to after the point where we have waited
for the primary thread to switch the MMU context and add the timebase
offset. That way we are sure that the timebase contains the guest
timebase value in both cases.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
In the next set of patches, we will switch pmd allocator to use page fragments
and the locking will be updated to split pmd ptlock. We want to avoid using
fragments for partition-scoped table. Use slab cache similar to level 4 table
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
During guest entry/exit, we switch over to/from the guest MMU context
and we cannot take exceptions in the hypervisor code.
Since ftrace may be enabled and since it can result in us taking a trap,
disable ftrace by setting paca->ftrace_enabled to zero. There are two
paths through which we enter/exit a guest:
1. If we are the vcore runner, then we enter the guest via
__kvmppc_vcore_entry() and we disable ftrace around this. This is always
the case for Power9, and for the primary thread on Power8.
2. If we are a secondary thread in Power8, then we would be in nap due
to SMT being disabled. We are woken up by an IPI to enter the guest. In
this scenario, we enter the guest through kvm_start_guest(). We disable
ftrace at this point. In this scenario, ftrace would only get re-enabled
on the secondary thread when SMT is re-enabled (via start_secondary()).
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Fix crashes when loading modules built with a different CONFIG_RELOCATABLE
value by adding CONFIG_RELOCATABLE to vermagic.
- Fix busy loops in the OPAL NVRAM driver if we get certain error conditions
from firmware.
- Remove tlbie trace points from KVM code that's called in real mode, because
it causes crashes.
- Fix checkstops caused by invalid tlbiel on Power9 Radix.
- Ensure the set of CPU features we "know" are always enabled is actually the
minimal set when we build with support for firmware supplied CPU features.
Thanks to:
Aneesh Kumar K.V, Anshuman Khandual, Nicholas Piggin.
-----BEGIN PGP SIGNATURE-----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=0e7c
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix crashes when loading modules built with a different
CONFIG_RELOCATABLE value by adding CONFIG_RELOCATABLE to vermagic.
- Fix busy loops in the OPAL NVRAM driver if we get certain error
conditions from firmware.
- Remove tlbie trace points from KVM code that's called in real mode,
because it causes crashes.
- Fix checkstops caused by invalid tlbiel on Power9 Radix.
- Ensure the set of CPU features we "know" are always enabled is
actually the minimal set when we build with support for firmware
supplied CPU features.
Thanks to: Aneesh Kumar K.V, Anshuman Khandual, Nicholas Piggin.
* tag 'powerpc-4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Fix CPU_FTRS_ALWAYS vs DT CPU features
powerpc/mm/radix: Fix checkstops caused by invalid tlbiel
KVM: PPC: Book3S HV: trace_tlbie must not be called in realmode
powerpc/8xx: Fix build with hugetlbfs enabled
powerpc/powernv: Fix OPAL NVRAM driver OPAL_BUSY loops
powerpc/powernv: define a standard delay for OPAL_BUSY type retry loops
powerpc/fscr: Enable interrupts earlier before calling get_user()
powerpc/64s: Fix section mismatch warnings from setup_rfi_flush()
powerpc/modules: Fix crashes by adding CONFIG_RELOCATABLE to vermagic
This crashes with a "Bad real address for load" attempting to load
from the vmalloc region in realmode (faulting address is in DAR).
Oops: Bad interrupt in KVM entry/exit code, sig: 6 [#1]
LE SMP NR_CPUS=2048 NUMA PowerNV
CPU: 53 PID: 6582 Comm: qemu-system-ppc Not tainted 4.16.0-01530-g43d1859f0994
NIP: c0000000000155ac LR: c0000000000c2430 CTR: c000000000015580
REGS: c000000fff76dd80 TRAP: 0200 Not tainted (4.16.0-01530-g43d1859f0994)
MSR: 9000000000201003 <SF,HV,ME,RI,LE> CR: 48082222 XER: 00000000
CFAR: 0000000102900ef0 DAR: d00017fffd941a28 DSISR: 00000040 SOFTE: 3
NIP [c0000000000155ac] perf_trace_tlbie+0x2c/0x1a0
LR [c0000000000c2430] do_tlbies+0x230/0x2f0
I suspect the reason is the per-cpu data is not in the linear chunk.
This could be restored if that was able to be fixed, but for now,
just remove the tracepoints.
Fixes: 0428491cba ("powerpc/mm: Trace tlbie(l) instructions")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- VHE optimizations
- EL2 address space randomization
- speculative execution mitigations ("variant 3a", aka execution past invalid
privilege register access)
- bugfixes and cleanups
PPC:
- improvements for the radix page fault handler for HV KVM on POWER9
s390:
- more kvm stat counters
- virtio gpu plumbing
- documentation
- facilities improvements
x86:
- support for VMware magic I/O port and pseudo-PMCs
- AMD pause loop exiting
- support for AMD core performance extensions
- support for synchronous register access
- expose nVMX capabilities to userspace
- support for Hyper-V signaling via eventfd
- use Enlightened VMCS when running on Hyper-V
- allow userspace to disable MWAIT/HLT/PAUSE vmexits
- usual roundup of optimizations and nested virtualization bugfixes
Generic:
- API selftest infrastructure (though the only tests are for x86 as of now)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJay19UAAoJEL/70l94x66DGKYIAIu9PTHAEwaX0et15fPW5y2x
rrtS355lSAmMrPJ1nePRQ+rProD/1B0Kizj3/9O+B9OTKKRsorRYNa4CSu9neO2k
N3rdE46M1wHAPwuJPcYvh3iBVXtgbMayk1EK5aVoSXaMXEHh+PWZextkl+F+G853
kC27yDy30jj9pStwnEFSBszO9ua/URdKNKBATNx8WUP6d9U/dlfm5xv3Dc3WtKt2
UMGmog2wh0i7ecXo7hRkMK4R7OYP3ZxAexq5aa9BOPuFp+ZdzC/MVpN+jsjq2J/M
Zq6RNyA2HFyQeP0E9QgFsYS2BNOPeLZnT5Jg1z4jyiD32lAZ/iC51zwm4oNKcDM=
=bPlD
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"ARM:
- VHE optimizations
- EL2 address space randomization
- speculative execution mitigations ("variant 3a", aka execution past
invalid privilege register access)
- bugfixes and cleanups
PPC:
- improvements for the radix page fault handler for HV KVM on POWER9
s390:
- more kvm stat counters
- virtio gpu plumbing
- documentation
- facilities improvements
x86:
- support for VMware magic I/O port and pseudo-PMCs
- AMD pause loop exiting
- support for AMD core performance extensions
- support for synchronous register access
- expose nVMX capabilities to userspace
- support for Hyper-V signaling via eventfd
- use Enlightened VMCS when running on Hyper-V
- allow userspace to disable MWAIT/HLT/PAUSE vmexits
- usual roundup of optimizations and nested virtualization bugfixes
Generic:
- API selftest infrastructure (though the only tests are for x86 as
of now)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (174 commits)
kvm: x86: fix a prototype warning
kvm: selftests: add sync_regs_test
kvm: selftests: add API testing infrastructure
kvm: x86: fix a compile warning
KVM: X86: Add Force Emulation Prefix for "emulate the next instruction"
KVM: X86: Introduce handle_ud()
KVM: vmx: unify adjacent #ifdefs
x86: kvm: hide the unused 'cpu' variable
KVM: VMX: remove bogus WARN_ON in handle_ept_misconfig
Revert "KVM: X86: Fix SMRAM accessing even if VM is shutdown"
kvm: Add emulation for movups/movupd
KVM: VMX: raise internal error for exception during invalid protected mode state
KVM: nVMX: Optimization: Dont set KVM_REQ_EVENT when VMExit with nested_run_pending
KVM: nVMX: Require immediate-exit when event reinjected to L2 and L1 event pending
KVM: x86: Fix misleading comments on handling pending exceptions
KVM: x86: Rename interrupt.pending to interrupt.injected
KVM: VMX: No need to clear pending NMI/interrupt on inject realmode interrupt
x86/kvm: use Enlightened VMCS when running on Hyper-V
x86/hyper-v: detect nested features
x86/hyper-v: define struct hv_enlightened_vmcs and clean field bits
...
Notable changes:
- Support for 4PB user address space on 64-bit, opt-in via mmap().
- Removal of POWER4 support, which was accidentally broken in 2016 and no one
noticed, and blocked use of some modern instructions.
- Workarounds so that the hypervisor can enable Transactional Memory on Power9.
- A series to disable the DAWR (Data Address Watchpoint Register) on Power9.
- More information displayed in the meltdown/spectre_v1/v2 sysfs files.
- A vpermxor (Power8 Altivec) implementation for the raid6 Q Syndrome.
- A big series to make the allocation of our pacas (per cpu area), kernel page
tables, and per-cpu stacks NUMA aware when using the Radix MMU on Power9.
And as usual many fixes, reworks and cleanups.
Thanks to:
Aaro Koskinen, Alexandre Belloni, Alexey Kardashevskiy, Alistair Popple, Andy
Shevchenko, Aneesh Kumar K.V, Anshuman Khandual, Balbir Singh, Benjamin
Herrenschmidt, Christophe Leroy, Christophe Lombard, Cyril Bur, Daniel Axtens,
Dave Young, Finn Thain, Frederic Barrat, Gustavo Romero, Horia Geantă,
Jonathan Neuschäfer, Kees Cook, Larry Finger, Laurent Dufour, Laurent Vivier,
Logan Gunthorpe, Madhavan Srinivasan, Mark Greer, Mark Hairgrove, Markus
Elfring, Mathieu Malaterre, Matt Brown, Matt Evans, Mauricio Faria de
Oliveira, Michael Neuling, Naveen N. Rao, Nicholas Piggin, Paul Mackerras,
Philippe Bergheaud, Ram Pai, Rob Herring, Sam Bobroff, Segher Boessenkool,
Simon Guo, Simon Horman, Stewart Smith, Sukadev Bhattiprolu, Suraj Jitindar
Singh, Thiago Jung Bauermann, Vaibhav Jain, Vaidyanathan Srinivasan, Vasant
Hegde, Wei Yongjun.
-----BEGIN PGP SIGNATURE-----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=HAB1
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- Support for 4PB user address space on 64-bit, opt-in via mmap().
- Removal of POWER4 support, which was accidentally broken in 2016
and no one noticed, and blocked use of some modern instructions.
- Workarounds so that the hypervisor can enable Transactional Memory
on Power9.
- A series to disable the DAWR (Data Address Watchpoint Register) on
Power9.
- More information displayed in the meltdown/spectre_v1/v2 sysfs
files.
- A vpermxor (Power8 Altivec) implementation for the raid6 Q
Syndrome.
- A big series to make the allocation of our pacas (per cpu area),
kernel page tables, and per-cpu stacks NUMA aware when using the
Radix MMU on Power9.
And as usual many fixes, reworks and cleanups.
Thanks to: Aaro Koskinen, Alexandre Belloni, Alexey Kardashevskiy,
Alistair Popple, Andy Shevchenko, Aneesh Kumar K.V, Anshuman Khandual,
Balbir Singh, Benjamin Herrenschmidt, Christophe Leroy, Christophe
Lombard, Cyril Bur, Daniel Axtens, Dave Young, Finn Thain, Frederic
Barrat, Gustavo Romero, Horia Geantă, Jonathan Neuschäfer, Kees Cook,
Larry Finger, Laurent Dufour, Laurent Vivier, Logan Gunthorpe,
Madhavan Srinivasan, Mark Greer, Mark Hairgrove, Markus Elfring,
Mathieu Malaterre, Matt Brown, Matt Evans, Mauricio Faria de Oliveira,
Michael Neuling, Naveen N. Rao, Nicholas Piggin, Paul Mackerras,
Philippe Bergheaud, Ram Pai, Rob Herring, Sam Bobroff, Segher
Boessenkool, Simon Guo, Simon Horman, Stewart Smith, Sukadev
Bhattiprolu, Suraj Jitindar Singh, Thiago Jung Bauermann, Vaibhav
Jain, Vaidyanathan Srinivasan, Vasant Hegde, Wei Yongjun"
* tag 'powerpc-4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (207 commits)
powerpc/64s/idle: Fix restore of AMOR on POWER9 after deep sleep
powerpc/64s: Fix POWER9 DD2.2 and above in cputable features
powerpc/64s: Fix pkey support in dt_cpu_ftrs, add CPU_FTR_PKEY bit
powerpc/64s: Fix dt_cpu_ftrs to have restore_cpu clear unwanted LPCR bits
Revert "powerpc/64s/idle: POWER9 ESL=0 stop avoid save/restore overhead"
powerpc: iomap.c: introduce io{read|write}64_{lo_hi|hi_lo}
powerpc: io.h: move iomap.h include so that it can use readq/writeq defs
cxl: Fix possible deadlock when processing page faults from cxllib
powerpc/hw_breakpoint: Only disable hw breakpoint if cpu supports it
powerpc/mm/radix: Update command line parsing for disable_radix
powerpc/mm/radix: Parse disable_radix commandline correctly.
powerpc/mm/hugetlb: initialize the pagetable cache correctly for hugetlb
powerpc/mm/radix: Update pte fragment count from 16 to 256 on radix
powerpc/mm/keys: Update documentation and remove unnecessary check
powerpc/64s/idle: POWER9 ESL=0 stop avoid save/restore overhead
powerpc/64s/idle: Consolidate power9_offline_stop()/power9_idle_stop()
powerpc/powernv: Always stop secondaries before reboot/shutdown
powerpc: hard disable irqs in smp_send_stop loop
powerpc: use NMI IPI for smp_send_stop
powerpc/powernv: Fix SMT4 forcing idle code
...
arch/powerpc/kvm/book3s_hv.c: In function ‘kvmppc_h_set_mode’:
arch/powerpc/kvm/book3s_hv.c:745:8: error: implicit declaration of function ‘ppc_breakpoint_available’
if (!ppc_breakpoint_available())
^~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 398e712c00 ("KVM: PPC: Book3S HV: Return error from h_set_mode(SET_DAWR) on POWER9")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER4 has been broken since at least the change 49d09bf2a6
("powerpc/64s: Optimise MSR handling in exception handling"), which
requires mtmsrd L=1 support. This was introduced in ISA v2.01, and
POWER4 supports ISA v2.00.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
SLOF checks for 'sc 1' (hypercall) support by issuing a hcall with
H_SET_DABR. Since the recent commit e8ebedbf31 ("KVM: PPC: Book3S
HV: Return error from h_set_dabr() on POWER9") changed H_SET_DABR to
return H_UNSUPPORTED on Power9, we see guest boot failures, the
symptom is the boot seems to just stop in SLOF, eg:
SLOF ***************************************************************
QEMU Starting
Build Date = Sep 24 2017 12:23:07
FW Version = buildd@ release 20170724
<no further output>
SLOF can cope if H_SET_DABR returns H_HARDWARE. So wwitch the return
value to H_HARDWARE instead of H_UNSUPPORTED so that we don't break
the guest boot.
That does mean we return a different error to PowerVM in this case,
but that's probably not a big concern.
Fixes: e8ebedbf31 ("KVM: PPC: Book3S HV: Return error from h_set_dabr() on POWER9")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Bring in yet another series that touches KVM code, and might need to
be merged into the kvm-ppc branch to resolve conflicts.
This required some changes in pnv_power9_force_smt4_catch/release()
due to the paca array becomming an array of pointers.
PPC:
- Fix a bug causing occasional machine check exceptions on POWER8 hosts
(introduced in 4.16-rc1)
x86:
- Fix a guest crashing regression with nested VMX and restricted guest
(introduced in 4.16-rc1)
- Fix dependency check for pv tlb flush (The wrong dependency that
effectively disabled the feature was added in 4.16-rc4, the original
feature in 4.16-rc1, so it got decent testing.)
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJavUt5AAoJEED/6hsPKofo8uQH/RuijrsAIUnymkYY+6BYFXlh
Ri8qhG8VB+C3SpWEtsqcqNVkjJTepCD2Ej5BJTL4Gc9BSTWy7Ht6kqskEgwcnzu2
xRfkg0q0vTj1+GDd+UiTZfxiinoHtB9x3fiXali5UNTCd1fweLxdidETfO+GqMMq
KDhTR+S8dXE5VG7r+iJ80LZPtHQJ94f0fh9XpQk3X2ExTG5RBxag1U2nCfiKRAZk
xRv1CNAxNaBxS38CgYfHzg31NJx38fnq/qREsIdOx0Ju9WQkglBFkhLAGUb4vL0I
nn8YX/oV9cW2G8tyPWjC245AouABOLbzu0xyj5KgCY/z1leA9tdLFX/ET6Zye+E=
=++uZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"PPC:
- Fix a bug causing occasional machine check exceptions on POWER8
hosts (introduced in 4.16-rc1)
x86:
- Fix a guest crashing regression with nested VMX and restricted
guest (introduced in 4.16-rc1)
- Fix dependency check for pv tlb flush (the wrong dependency that
effectively disabled the feature was added in 4.16-rc4, the
original feature in 4.16-rc1, so it got decent testing)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Fix pv tlb flush dependencies
KVM: nVMX: sync vmcs02 segment regs prior to vmx_set_cr0
KVM: PPC: Book3S HV: Fix duplication of host SLB entries
We no longer allocate lppacas in an array, so this patch removes the
1kB static alignment for the structure, and enforces the PAPR
alignment requirements at allocation time. We can not reduce the 1kB
allocation size however, due to existing KVM hypervisors.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Change the paca array into an array of pointers to pacas. Allocate
pacas individually.
This allows flexibility in where the PACAs are allocated. Future work
will allocate them node-local. Platforms that don't have address limits
on PACAs would be able to defer PACA allocations until later in boot
rather than allocate all possible ones up-front then freeing unused.
This is slightly more overhead (one additional indirection) for cross
CPU paca references, but those aren't too common.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The "lppaca" is a structure registered with the hypervisor. This is
unnecessary when running on non-virtualised platforms. One field from
the lppaca (pmcregs_in_use) is also used by the host, so move the host
part out into the paca (lppaca field is still updated in
guest mode).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Fix non-pseries build with some #ifdefs]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These are actually all fixes for pre-4.16 code, or new hardware workarounds.
Fix missing AT_BASE_PLATFORM (in auxv) when we're using a new firmware interface
for describing CPU features.
Fix lost pending interrupts due to a race in our interrupt soft-masking code.
A workaround for a nest MMU bug with TLB invalidations on Power9.
A workaround for broadcast TLB invalidations on Power9.
Fix a bug in our instruction SLB miss handler, when handling bad addresses
(eg. >= TASK_SIZE), which could corrupt non-volatile user GPRs.
Thanks to:
Aneesh Kumar K.V, Balbir Singh, Benjamin Herrenschmidt, Nicholas Piggin.
-----BEGIN PGP SIGNATURE-----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=qP8V
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.16-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Some more powerpc fixes for 4.16. Apologies if this is a bit big at
rc7, but they're all reasonably important fixes. None are actually for
new code, so they aren't indicative of 4.16 being in bad shape from
our point of view.
- Fix missing AT_BASE_PLATFORM (in auxv) when we're using a new
firmware interface for describing CPU features.
- Fix lost pending interrupts due to a race in our interrupt
soft-masking code.
- A workaround for a nest MMU bug with TLB invalidations on Power9.
- A workaround for broadcast TLB invalidations on Power9.
- Fix a bug in our instruction SLB miss handler, when handling bad
addresses (eg. >= TASK_SIZE), which could corrupt non-volatile user
GPRs.
Thanks to: Aneesh Kumar K.V, Balbir Singh, Benjamin Herrenschmidt,
Nicholas Piggin"
* tag 'powerpc-4.16-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Fix i-side SLB miss bad address handler saving nonvolatile GPRs
powerpc/mm: Fixup tlbie vs store ordering issue on POWER9
powerpc/mm/radix: Move the functions that does the actual tlbie closer
powerpc/mm/radix: Remove unused code
powerpc/mm: Workaround Nest MMU bug with TLB invalidations
powerpc/mm: Add tracking of the number of coprocessors using a context
powerpc/64s: Fix lost pending interrupt due to race causing lost update to irq_happened
powerpc/64s: Fix NULL AT_BASE_PLATFORM when using DT CPU features
Merge our fixes branch from the 4.16 cycle.
There were a number of important fixes merged, in particular some Power9
workarounds that we want in next for testing purposes. There's also been
some conflicting changes in the CPU features code which are best merged
and tested before going upstream.
This changes the hypervisor page fault handler for radix guests to use
the generic KVM __gfn_to_pfn_memslot() function instead of using
get_user_pages_fast() and then handling the case of VM_PFNMAP vmas
specially. The old code missed the case of VM_IO vmas; with this
change, VM_IO vmas will now be handled correctly by code within
__gfn_to_pfn_memslot.
Currently, __gfn_to_pfn_memslot calls hva_to_pfn, which only uses
__get_user_pages_fast for the initial lookup in the cases where
either atomic or async is set. Since we are not setting either
atomic or async, we do our own __get_user_pages_fast first, for now.
This also adds code to check for the KVM_MEM_READONLY flag on the
memslot. If it is set and this is a write access, we synthesize a
data storage interrupt for the guest.
In the case where the page is not normal RAM (i.e. page == NULL in
kvmppc_book3s_radix_page_fault(), we read the PTE from the Linux page
tables because we need the mapping attribute bits as well as the PFN.
(The mapping attribute bits indicate whether accesses have to be
non-cacheable and/or guarded.)
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
POWER9 with the DAWR disabled causes problems for partition
migration. Either we have to fail the migration (since we lose the
DAWR) or we silently drop the DAWR and allow the migration to pass.
This patch does the latter and allows the migration to pass (at the
cost of silently losing the DAWR). This is not ideal but hopefully the
best overall solution. This approach has been acked by Paulus.
With this patch kvmppc_set_one_reg() will store the DAWR in the vcpu
but won't actually set it on POWER9 hardware.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER7 compat mode guests can use h_set_dabr on POWER9. POWER9 should
use the DAWR but since it's disabled there we can't.
This returns H_UNSUPPORTED on a h_set_dabr() on POWER9 where the DAWR
is disabled.
Current Linux guests ignore this error, so they will silently not get
the DAWR (sigh). The same error code is being used by POWERVM in this
case.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Return H_P2 on a h_set_mode(SET_DAWR) on POWER9 where the DAWR is
disabled.
Current Linux guests ignore this error, so they will silently not get
the DAWR (sigh). The same error code is being used by POWERVM in this
case.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This works around a hardware bug in "Nimbus" POWER9 DD2.2 processors,
where the contents of the TEXASR can get corrupted while a thread is
in fake suspend state. The workaround is for the instruction emulation
code to use the value saved at the most recent guest exit in real
suspend mode. We achieve this by simply not saving the TEXASR into
the vcpu struct on an exit in fake suspend state. We also have to
take care to set the orig_texasr field only on guest exit in real
suspend state.
This also means that on guest entry in fake suspend state, TEXASR
will be restored to the value it had on the last exit in real suspend
state, effectively counteracting any hardware-caused corruption. This
works because TEXASR may not be written in suspend state.
With this, the guest might see the wrong values in TEXASR if it reads
it while in suspend state, but will see the correct value in
non-transactional state (e.g. after a treclaim), and treclaim will
work correctly.
With this workaround, the code will actually run slightly faster, and
will operate correctly on systems without the TEXASR bug (since TEXASR
may not be written in suspend state, and is only changed by failure
recording, which will have already been done before we get into fake
suspend state). Therefore these changes are not made subject to a CPU
feature bit.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This works around a hardware bug in "Nimbus" POWER9 DD2.2 processors,
where a treclaim performed in fake suspend mode can cause subsequent
reads from the XER register to return inconsistent values for the SO
(summary overflow) bit. The inconsistent SO bit state can potentially
be observed on any thread in the core. We have to do the treclaim
because that is the only way to get the thread out of suspend state
(fake or real) and into non-transactional state.
The workaround for the bug is to force the core into SMT4 mode before
doing the treclaim. This patch adds the code to do that, conditional
on the CPU_FTR_P9_TM_XER_SO_BUG feature bit.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 has hardware bugs relating to transactional memory and thread
reconfiguration (changes to hardware SMT mode). Specifically, the core
does not have enough storage to store a complete checkpoint of all the
architected state for all four threads. The DD2.2 version of POWER9
includes hardware modifications designed to allow hypervisor software
to implement workarounds for these problems. This patch implements
those workarounds in KVM code so that KVM guests see a full, working
transactional memory implementation.
The problems center around the use of TM suspended state, where the
CPU has a checkpointed state but execution is not transactional. The
workaround is to implement a "fake suspend" state, which looks to the
guest like suspended state but the CPU does not store a checkpoint.
In this state, any instruction that would cause a transition to
transactional state (rfid, rfebb, mtmsrd, tresume) or would use the
checkpointed state (treclaim) causes a "soft patch" interrupt (vector
0x1500) to the hypervisor so that it can be emulated. The trechkpt
instruction also causes a soft patch interrupt.
On POWER9 DD2.2, we avoid returning to the guest in any state which
would require a checkpoint to be present. The trechkpt in the guest
entry path which would normally create that checkpoint is replaced by
either a transition to fake suspend state, if the guest is in suspend
state, or a rollback to the pre-transactional state if the guest is in
transactional state. Fake suspend state is indicated by a flag in the
PACA plus a new bit in the PSSCR. The new PSSCR bit is write-only and
reads back as 0.
On exit from the guest, if the guest is in fake suspend state, we still
do the treclaim instruction as we would in real suspend state, in order
to get into non-transactional state, but we do not save the resulting
register state since there was no checkpoint.
Emulation of the instructions that cause a softpatch interrupt is
handled in two paths. If the guest is in real suspend mode, we call
kvmhv_p9_tm_emulation_early() to handle the cases where the guest is
transitioning to transactional state. This is called before we do the
treclaim in the guest exit path; because we haven't done treclaim, we
can get back to the guest with the transaction still active. If the
instruction is a case that kvmhv_p9_tm_emulation_early() doesn't
handle, or if the guest is in fake suspend state, then we proceed to
do the complete guest exit path and subsequently call
kvmhv_p9_tm_emulation() in host context with the MMU on. This handles
all the cases including the cases that generate program interrupts
(illegal instruction or TM Bad Thing) and facility unavailable
interrupts.
The emulation is reasonably straightforward and is mostly concerned
with checking for exception conditions and updating the state of
registers such as MSR and CR0. The treclaim emulation takes care to
ensure that the TEXASR register gets updated as if it were the guest
treclaim instruction that had done failure recording, not the treclaim
done in hypervisor state in the guest exit path.
With this, the KVM_CAP_PPC_HTM capability returns true (1) even if
transactional memory is not available to host userspace.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On POWER9, under some circumstances, a broadcast TLB invalidation
might complete before all previous stores have drained, potentially
allowing stale stores from becoming visible after the invalidation.
This works around it by doubling up those TLB invalidations which was
verified by HW to be sufficient to close the risk window.
This will be documented in a yet-to-be-published errata.
Fixes: 1a472c9dba ("powerpc/mm/radix: Add tlbflush routines")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Enable the feature in the DT CPU features code for all Power9,
rename the feature to CPU_FTR_P9_TLBIE_BUG per benh.]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit 6964e6a4e4 ("KVM: PPC: Book3S HV: Do SLB load/unload
with guest LPCR value loaded", 2018-01-11), we have been seeing
occasional machine check interrupts on POWER8 systems when running
KVM guests, due to SLB multihit errors.
This turns out to be due to the guest exit code reloading the host
SLB entries from the SLB shadow buffer when the SLB was not previously
cleared in the guest entry path. This can happen because the path
which skips from the guest entry code to the guest exit code without
entering the guest now does the skip before the SLB is cleared and
loaded with guest values, but the host values are loaded after the
point in the guest exit path that we skip to.
To fix this, we move the code that reloads the host SLB values up
so that it occurs just before the point in the guest exit code (the
label guest_bypass:) where we skip to from the guest entry path.
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Fixes: 6964e6a4e4 ("KVM: PPC: Book3S HV: Do SLB load/unload with guest LPCR value loaded")
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds code to the radix hypervisor page fault handler to handle the
case where the guest memory is backed by 1GB hugepages, and put them
into the partition-scoped radix tree at the PUD level. The code is
essentially analogous to the code for 2MB pages. This also rearranges
kvmppc_create_pte() to make it easier to follow.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When using the radix MMU, we can get hypervisor page fault interrupts
with the DSISR_SET_RC bit set in DSISR/HSRR1, indicating that an
attempt to set the R (reference) or C (change) bit in a PTE atomically
failed. Previously we would find the corresponding Linux PTE and
check the permission and dirty bits there, but this is not really
necessary since we only need to do what the hardware was trying to
do, namely set R or C atomically. This removes the code that reads
the Linux PTE and just update the partition-scoped PTE, having first
checked that it is still present, and if the access is a write, that
the PTE still has write permission.
Furthermore, we now check whether any other relevant bits are set
in DSISR, and if there are, then we proceed with the rest of the
function in order to handle whatever condition they represent,
instead of returning to the guest as we did previously.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This improves the handling of transparent huge pages in the radix
hypervisor page fault handler. Previously, if a small page is faulted
in to a 2MB region of guest physical space, that means that there is
a page table pointer at the PMD level, which could never be replaced
by a leaf (2MB) PMD entry. This adds the code to clear the PMD,
invlidate the page walk cache and free the page table page in this
situation, so that the leaf PMD entry can be created.
This also adds code to check whether a PMD or PTE being inserted is
the same as is already there (because of a race with another CPU that
faulted on the same page) and if so, we don't replace the existing
entry, meaning that we don't invalidate the PTE or PMD and do a TLB
invalidation.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Since commit fb1522e099 ("KVM: update to new mmu_notifier semantic
v2", 2017-08-31), the MMU notifier code in KVM no longer calls the
kvm_unmap_hva callback. This removes the PPC implementations of
kvm_unmap_hva().
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This fixes a bug where the trap number that is returned by
__kvmppc_vcore_entry gets corrupted. The effect of the corruption
is that IPIs get ignored on POWER9 systems when the IPI is sent via
a doorbell interrupt to a CPU which is executing in a KVM guest.
The effect of the IPI being ignored is often that another CPU locks
up inside smp_call_function_many() (and if that CPU is holding a
spinlock, other CPUs then lock up inside raw_spin_lock()).
The trap number is currently held in register r12 for most of the
assembly-language part of the guest exit path. In that path, we
call kvmppc_subcore_exit_guest(), which is a C function, without
restoring r12 afterwards. Depending on the kernel config and the
compiler, it may modify r12 or it may not, so some config/compiler
combinations see the bug and others don't.
To fix this, we arrange for the trap number to be stored on the
stack from the 'guest_bypass:' label until the end of the function,
then the trap number is loaded and returned in r12 as before.
Cc: stable@vger.kernel.org # v4.8+
Fixes: fd7bacbca4 ("KVM: PPC: Book3S HV: Fix TB corruption in guest exit path on HMI interrupt")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
- Fix guest time accounting in the host
- Fix large-page backing for radix guests on POWER9
- Fix HPT guests on POWER9 backed by 2M or 1G pages
- Compile fixes for some configs and gcc versions
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJammR1AAoJEJ2a6ncsY3Gf2pQIAKf1sBKimpDj/yeBlWVbS41q
6mIJh8R+4DV7TcOSVoOdzUz1dU1cseVznqqr3kexu+unoUpcqm240ZUDsDNWy9j0
Xv0JyrGOcPor9sQmlb1s2gOsybxhic4u8Ih1eQV47bEUw1Rb84/da0JI1u5nMRTq
nm3OHPGSnK2C8UkBBVjGelLJGUx+uaLFLjJSSTd0F9+hlxjGT3yXjP3wLG/ZNajT
6Reuzpr95hGpmIaml8gh73clLk4WAjF3+5SyiLo5nlsXzvMnC0DyzaUrHocIo6i7
nZxrx9UguzEdiUbuc5NEs4klTc+GPwMCfd+7z6vmtyw87A0sVOUgGWNGcZL60ew=
=Wy2j
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-fixes-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
Fixes for PPC KVM:
- Fix guest time accounting in the host
- Fix large-page backing for radix guests on POWER9
- Fix HPT guests on POWER9 backed by 2M or 1G pages
- Compile fixes for some configs and gcc versions
Since commit 8b24e69fc4 ("KVM: PPC: Book3S HV: Close race with testing
for signals on guest entry"), if CONFIG_VIRT_CPU_ACCOUNTING_GEN is set, the
guest time is not accounted to guest time and user time, but instead to
system time.
This is because guest_enter()/guest_exit() are called while interrupts
are disabled and the tick counter cannot be updated between them.
To fix that, move guest_exit() after local_irq_enable(), and as
guest_enter() is called with IRQ disabled, call guest_enter_irqoff()
instead.
Fixes: 8b24e69fc4 ("KVM: PPC: Book3S HV: Close race with testing for signals on guest entry")
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The current code for initializing the VRMA (virtual real memory area)
for HPT guests requires the page size of the backing memory to be one
of 4kB, 64kB or 16MB. With a radix host we have the possibility that
the backing memory page size can be 2MB or 1GB. In these cases, if the
guest switches to HPT mode, KVM will not initialize the VRMA and the
guest will fail to run.
In fact it is not necessary that the VRMA page size is the same as the
backing memory page size; any VRMA page size less than or equal to the
backing memory page size is acceptable. Therefore we now choose the
largest page size out of the set {4k, 64k, 16M} which is not larger
than the backing memory page size.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This fixes several bugs in the radix page fault handler relating to
the way large pages in the memory backing the guest were handled.
First, the check for large pages only checked for explicit huge pages
and missed transparent huge pages. Then the check that the addresses
(host virtual vs. guest physical) had appropriate alignment was
wrong, meaning that the code never put a large page in the partition
scoped radix tree; it was always demoted to a small page.
Fixing this exposed bugs in kvmppc_create_pte(). We were never
invalidating a 2MB PTE, which meant that if a page was initially
faulted in without write permission and the guest then attempted
to store to it, we would never update the PTE to have write permission.
If we find a valid 2MB PTE in the PMD, we need to clear it and
do a TLB invalidation before installing either the new 2MB PTE or
a pointer to a page table page.
This also corrects an assumption that get_user_pages_fast would set
the _PAGE_DIRTY bit if we are writing, which is not true. Instead we
mark the page dirty explicitly with set_page_dirty_lock(). This
also means we don't need the dirty bit set on the host PTE when
providing write access on a read fault.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
On lkml suggestions were made to split up such trivial typo fixes into per subsystem
patches:
--- a/arch/x86/boot/compressed/eboot.c
+++ b/arch/x86/boot/compressed/eboot.c
@@ -439,7 +439,7 @@ setup_uga32(void **uga_handle, unsigned long size, u32 *width, u32 *height)
struct efi_uga_draw_protocol *uga = NULL, *first_uga;
efi_guid_t uga_proto = EFI_UGA_PROTOCOL_GUID;
unsigned long nr_ugas;
- u32 *handles = (u32 *)uga_handle;;
+ u32 *handles = (u32 *)uga_handle;
efi_status_t status = EFI_INVALID_PARAMETER;
int i;
This patch is the result of the following script:
$ sed -i 's/;;$/;/g' $(git grep -E ';;$' | grep "\.[ch]:" | grep -vwE 'for|ia64' | cut -d: -f1 | sort | uniq)
... followed by manual review to make sure it's all good.
Splitting this up is just crazy talk, let's get over with this and just do it.
Reported-by: Pavel Machek <pavel@ucw.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Some versions of gcc generate a warning that the variable "emulated"
may be used uninitialized in function kvmppc_handle_load128_by2x64().
It would be used uninitialized if kvmppc_handle_load128_by2x64 was
ever called with vcpu->arch.mmio_vmx_copy_nums == 0, but neither of
the callers ever do that, so there is no actual bug. When gcc
generates a warning, it causes the build to fail because arch/powerpc
is compiled with -Werror.
This silences the warning by initializing "emulated" to EMULATE_DONE.
Fixes: 09f984961c ("KVM: PPC: Book3S: Add MMIO emulation for VMX instructions")
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Commit accb757d79 ("KVM: Move vcpu_load to arch-specific
kvm_arch_vcpu_ioctl_run", 2017-12-04) added a "goto out"
statement and an "out:" label to kvm_arch_vcpu_ioctl_run().
Since the only "goto out" is inside a CONFIG_VSX block,
compiling with CONFIG_VSX=n gives a warning that label "out"
is defined but not used, and because arch/powerpc is compiled
with -Werror, that becomes a compile error that makes the kernel
build fail.
Merge commit 1ab03c072f ("Merge tag 'kvm-ppc-next-4.16-2' of
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc",
2018-02-09) added a similar block of code inside a #ifdef
CONFIG_ALTIVEC, with a "goto out" statement.
In order to make the build succeed, this adds a #ifdef around the
"out:" label. This is a minimal, ugly fix, to be replaced later
by a refactoring of the code. Since CONFIG_VSX depends on
CONFIG_ALTIVEC, it is sufficient to use #ifdef CONFIG_ALTIVEC here.
Fixes: accb757d79 ("KVM: Move vcpu_load to arch-specific kvm_arch_vcpu_ioctl_run")
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
ARM:
- Include icache invalidation optimizations, improving VM startup time
- Support for forwarded level-triggered interrupts, improving
performance for timers and passthrough platform devices
- A small fix for power-management notifiers, and some cosmetic changes
PPC:
- Add MMIO emulation for vector loads and stores
- Allow HPT guests to run on a radix host on POWER9 v2.2 CPUs without
requiring the complex thread synchronization of older CPU versions
- Improve the handling of escalation interrupts with the XIVE interrupt
controller
- Support decrement register migration
- Various cleanups and bugfixes.
s390:
- Cornelia Huck passed maintainership to Janosch Frank
- Exitless interrupts for emulated devices
- Cleanup of cpuflag handling
- kvm_stat counter improvements
- VSIE improvements
- mm cleanup
x86:
- Hypervisor part of SEV
- UMIP, RDPID, and MSR_SMI_COUNT emulation
- Paravirtualized TLB shootdown using the new KVM_VCPU_PREEMPTED bit
- Allow guests to see TOPOEXT, GFNI, VAES, VPCLMULQDQ, and more AVX512
features
- Show vcpu id in its anonymous inode name
- Many fixes and cleanups
- Per-VCPU MSR bitmaps (already merged through x86/pti branch)
- Stable KVM clock when nesting on Hyper-V (merged through x86/hyperv)
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJafvMtAAoJEED/6hsPKofo6YcH/Rzf2RmshrWaC3q82yfIV0Qz
Z8N8yJHSaSdc3Jo6cmiVj0zelwAxdQcyjwlT7vxt5SL2yML+/Q0st9Hc3EgGGXPm
Il99eJEl+2MYpZgYZqV8ff3mHS5s5Jms+7BITAeh6Rgt+DyNbykEAvzt+MCHK9cP
xtsIZQlvRF7HIrpOlaRzOPp3sK2/MDZJ1RBE7wYItK3CUAmsHim/LVYKzZkRTij3
/9b4LP1yMMbziG+Yxt1o682EwJB5YIat6fmDG9uFeEVI5rWWN7WFubqs8gCjYy/p
FX+BjpOdgTRnX+1m9GIj0Jlc/HKMXryDfSZS07Zy4FbGEwSiI5SfKECub4mDhuE=
=C/uD
-----END PGP SIGNATURE-----
Merge tag 'kvm-4.16-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Radim Krčmář:
"ARM:
- icache invalidation optimizations, improving VM startup time
- support for forwarded level-triggered interrupts, improving
performance for timers and passthrough platform devices
- a small fix for power-management notifiers, and some cosmetic
changes
PPC:
- add MMIO emulation for vector loads and stores
- allow HPT guests to run on a radix host on POWER9 v2.2 CPUs without
requiring the complex thread synchronization of older CPU versions
- improve the handling of escalation interrupts with the XIVE
interrupt controller
- support decrement register migration
- various cleanups and bugfixes.
s390:
- Cornelia Huck passed maintainership to Janosch Frank
- exitless interrupts for emulated devices
- cleanup of cpuflag handling
- kvm_stat counter improvements
- VSIE improvements
- mm cleanup
x86:
- hypervisor part of SEV
- UMIP, RDPID, and MSR_SMI_COUNT emulation
- paravirtualized TLB shootdown using the new KVM_VCPU_PREEMPTED bit
- allow guests to see TOPOEXT, GFNI, VAES, VPCLMULQDQ, and more
AVX512 features
- show vcpu id in its anonymous inode name
- many fixes and cleanups
- per-VCPU MSR bitmaps (already merged through x86/pti branch)
- stable KVM clock when nesting on Hyper-V (merged through
x86/hyperv)"
* tag 'kvm-4.16-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (197 commits)
KVM: PPC: Book3S: Add MMIO emulation for VMX instructions
KVM: PPC: Book3S HV: Branch inside feature section
KVM: PPC: Book3S HV: Make HPT resizing work on POWER9
KVM: PPC: Book3S HV: Fix handling of secondary HPTEG in HPT resizing code
KVM: PPC: Book3S PR: Fix broken select due to misspelling
KVM: x86: don't forget vcpu_put() in kvm_arch_vcpu_ioctl_set_sregs()
KVM: PPC: Book3S PR: Fix svcpu copying with preemption enabled
KVM: PPC: Book3S HV: Drop locks before reading guest memory
kvm: x86: remove efer_reload entry in kvm_vcpu_stat
KVM: x86: AMD Processor Topology Information
x86/kvm/vmx: do not use vm-exit instruction length for fast MMIO when running nested
kvm: embed vcpu id to dentry of vcpu anon inode
kvm: Map PFN-type memory regions as writable (if possible)
x86/kvm: Make it compile on 32bit and with HYPYERVISOR_GUEST=n
KVM: arm/arm64: Fixup userspace irqchip static key optimization
KVM: arm/arm64: Fix userspace_irqchip_in_use counting
KVM: arm/arm64: Fix incorrect timer_is_pending logic
MAINTAINERS: update KVM/s390 maintainers
MAINTAINERS: add Halil as additional vfio-ccw maintainer
MAINTAINERS: add David as a reviewer for KVM/s390
...
Seven fixes that are either trivial or that address bugs that people
are actually hitting. The main ones are:
- Drop spinlocks before reading guest memory
- Fix a bug causing corruption of VCPU state in PR KVM with preemption
enabled
- Make HPT resizing work on POWER9
- Add MMIO emulation for vector loads and stores, because guests now
use these instructions in memcpy and similar routines.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJafWn0AAoJEJ2a6ncsY3GfaMsIANF0hQD8SS78WNKnoy0vnZ/X
PUXdjwHEsfkg5KdQ7o0oaa2BJHHqO3vozddmMiG14r2L1mNCHJpnVZCVV0GaEJcZ
eU8++OPK6yrsPNNpAjnrtQ0Vk4LwzoT0bftEjS3TtLt1s2uSo+R1+HLmxbxGhQUX
bZngo9wQ3cjUfAXLrPtAVhE5wTmgVOiufVRyfRsBRdFzRsAWqjY4hBtJAfwdff4r
AA5H0RCrXO6e1feKr5ElU8KzX6b7IjH9Xu868oJ1r16zZfE05PBl1X5n4XG7XDm7
xWvs8uLAB7iRv2o/ecFznYJ+Dz1NCBVzD0RmAUTqPCcVKDrxixaTkqMPFW97IAA=
=HOJR
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-next-4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
Second PPC KVM update for 4.16
Seven fixes that are either trivial or that address bugs that people
are actually hitting. The main ones are:
- Drop spinlocks before reading guest memory
- Fix a bug causing corruption of VCPU state in PR KVM with preemption
enabled
- Make HPT resizing work on POWER9
- Add MMIO emulation for vector loads and stores, because guests now
use these instructions in memcpy and similar routines.
This patch provides the MMIO load/store vector indexed
X-Form emulation.
Instructions implemented:
lvx: the quadword in storage addressed by the result of EA &
0xffff_ffff_ffff_fff0 is loaded into VRT.
stvx: the contents of VRS are stored into the quadword in storage
addressed by the result of EA & 0xffff_ffff_ffff_fff0.
Reported-by: Gopesh Kumar Chaudhary <gopchaud@in.ibm.com>
Reported-by: Balamuruhan S <bala24@linux.vnet.ibm.com>
Signed-off-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
We ended up with code that did a conditional branch inside a feature
section to code outside of the feature section. Depending on how the
object file gets organized, that might mean we exceed the 14bit
relocation limit for conditional branches:
arch/powerpc/kvm/built-in.o:arch/powerpc/kvm/book3s_hv_rmhandlers.S:416:(__ftr_alt_97+0x8): relocation truncated to fit: R_PPC64_REL14 against `.text'+1ca4
So instead of doing a conditional branch outside of the feature section,
let's just jump at the end of the same, making the branch very short.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds code to enable the HPT resizing code to work on POWER9,
which uses a slightly modified HPT entry format compared to POWER8.
On POWER9, we convert HPTEs read from the HPT from the new format to
the old format so that the rest of the HPT resizing code can work as
before. HPTEs written to the new HPT are converted to the new format
as the last step before writing them into the new HPT.
This takes out the checks added by commit bcd3bb63db ("KVM: PPC:
Book3S HV: Disable HPT resizing on POWER9 for now", 2017-02-18),
now that HPT resizing works on POWER9.
On POWER9, when we pivot to the new HPT, we now call
kvmppc_setup_partition_table() to update the partition table in order
to make the hardware use the new HPT.
[paulus@ozlabs.org - added kvmppc_setup_partition_table() call,
wrote commit message.]
Tested-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This fixes the computation of the HPTE index to use when the HPT
resizing code encounters a bolted HPTE which is stored in its
secondary HPTE group. The code inverts the HPTE group number, which
is correct, but doesn't then mask it with new_hash_mask. As a result,
new_pteg will be effectively negative, resulting in new_hptep
pointing before the new HPT, which will corrupt memory.
In addition, this removes two BUG_ON statements. The condition that
the BUG_ONs were testing -- that we have computed the hash value
incorrectly -- has never been observed in testing, and if it did
occur, would only affect the guest, not the host. Given that
BUG_ON should only be used in conditions where the kernel (i.e.
the host kernel, in this case) can't possibly continue execution,
it is not appropriate here.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Commit 76d837a4c0 ("KVM: PPC: Book3S PR: Don't include SPAPR TCE code
on non-pseries platforms") added a reference to the globally undefined
symbol PPC_SERIES. Looking at the rest of the commit, PPC_PSERIES was
probably intended.
Change PPC_SERIES to PPC_PSERIES.
Discovered with the
https://github.com/ulfalizer/Kconfiglib/blob/master/examples/list_undefined.py
script.
Fixes: 76d837a4c0 ("KVM: PPC: Book3S PR: Don't include SPAPR TCE code on non-pseries platforms")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Highlights:
- Enable support for memory protection keys aka "pkeys" on Power7/8/9 when
using the hash table MMU.
- Extend our interrupt soft masking to support masking PMU interrupts as well
as "normal" interrupts, and then use that to implement local_t for a ~4x
speedup vs the current atomics-based implementation.
- A new driver "ocxl" for "Open Coherent Accelerator Processor Interface
(OpenCAPI)" devices.
- Support for new device tree properties on PowerVM to describe hotpluggable
memory and devices.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 64-bit VDSO.
- Freescale updates from Scott:
"Contains fixes for CPM GPIO and an FSL PCI erratum workaround, plus a
minor cleanup patch."
As well as quite a lot of other changes all over the place, and small fixes and
cleanups as always.
Thanks to:
Alan Modra, Alastair D'Silva, Alexey Kardashevskiy, Alistair Popple, Andreas
Schwab, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Anshuman
Khandual, Anton Blanchard, Arnd Bergmann, Balbir Singh, Benjamin
Herrenschmidt, Bhaktipriya Shridhar, Bryant G. Ly, Cédric Le Goater,
Christophe Leroy, Christophe Lombard, Cyril Bur, David Gibson, Desnes A. Nunes
do Rosario, Dmitry Torokhov, Frederic Barrat, Geert Uytterhoeven, Guilherme G.
Piccoli, Gustavo A. R. Silva, Gustavo Romero, Ivan Mikhaylov, Joakim
Tjernlund, Joe Perches, Josh Poimboeuf, Juan J. Alvarez, Julia Cartwright,
Kamalesh Babulal, Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu Malaterre,
Michael Bringmann, Michael Hanselmann, Michael Neuling, Nathan Fontenot,
Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Philippe Bergheaud, Ram Pai,
Russell Currey, Santosh Sivaraj, Scott Wood, Seth Forshee, Simon Guo, Stewart
Smith, Sukadev Bhattiprolu, Thiago Jung Bauermann, Vaibhav Jain, Vasyl
Gomonovych.
-----BEGIN PGP SIGNATURE-----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=3rYn
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- Enable support for memory protection keys aka "pkeys" on Power7/8/9
when using the hash table MMU.
- Extend our interrupt soft masking to support masking PMU interrupts
as well as "normal" interrupts, and then use that to implement
local_t for a ~4x speedup vs the current atomics-based
implementation.
- A new driver "ocxl" for "Open Coherent Accelerator Processor
Interface (OpenCAPI)" devices.
- Support for new device tree properties on PowerVM to describe
hotpluggable memory and devices.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 64-bit
VDSO.
- Freescale updates from Scott: fixes for CPM GPIO and an FSL PCI
erratum workaround, plus a minor cleanup patch.
As well as quite a lot of other changes all over the place, and small
fixes and cleanups as always.
Thanks to: Alan Modra, Alastair D'Silva, Alexey Kardashevskiy,
Alistair Popple, Andreas Schwab, Andrew Donnellan, Aneesh Kumar K.V,
Anju T Sudhakar, Anshuman Khandual, Anton Blanchard, Arnd Bergmann,
Balbir Singh, Benjamin Herrenschmidt, Bhaktipriya Shridhar, Bryant G.
Ly, Cédric Le Goater, Christophe Leroy, Christophe Lombard, Cyril Bur,
David Gibson, Desnes A. Nunes do Rosario, Dmitry Torokhov, Frederic
Barrat, Geert Uytterhoeven, Guilherme G. Piccoli, Gustavo A. R. Silva,
Gustavo Romero, Ivan Mikhaylov, Joakim Tjernlund, Joe Perches, Josh
Poimboeuf, Juan J. Alvarez, Julia Cartwright, Kamalesh Babulal,
Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu Malaterre, Michael
Bringmann, Michael Hanselmann, Michael Neuling, Nathan Fontenot,
Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Philippe Bergheaud,
Ram Pai, Russell Currey, Santosh Sivaraj, Scott Wood, Seth Forshee,
Simon Guo, Stewart Smith, Sukadev Bhattiprolu, Thiago Jung Bauermann,
Vaibhav Jain, Vasyl Gomonovych"
* tag 'powerpc-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (199 commits)
powerpc/mm/radix: Fix build error when RADIX_MMU=n
macintosh/ams-input: Use true and false for boolean values
macintosh: change some data types from int to bool
powerpc/watchdog: Print the NIP in soft_nmi_interrupt()
powerpc/watchdog: regs can't be null in soft_nmi_interrupt()
powerpc/watchdog: Tweak watchdog printks
powerpc/cell: Remove axonram driver
rtc-opal: Fix handling of firmware error codes, prevent busy loops
powerpc/mpc52xx_gpt: make use of raw_spinlock variants
macintosh/adb: Properly mark continued kernel messages
powerpc/pseries: Fix cpu hotplug crash with memoryless nodes
powerpc/numa: Ensure nodes initialized for hotplug
powerpc/numa: Use ibm,max-associativity-domains to discover possible nodes
powerpc/kernel: Block interrupts when updating TIDR
powerpc/powernv/idoa: Remove unnecessary pcidev from pci_dn
powerpc/mm/nohash: do not flush the entire mm when range is a single page
powerpc/pseries: Add Initialization of VF Bars
powerpc/pseries/pci: Associate PEs to VFs in configure SR-IOV
powerpc/eeh: Add EEH notify resume sysfs
powerpc/eeh: Add EEH operations to notify resume
...
- Allow HPT guests to run on a radix host on POWER9 v2.2 CPUs
without requiring the complex thread synchronization that earlier
CPU versions required.
- A series from Ben Herrenschmidt to improve the handling of
escalation interrupts with the XIVE interrupt controller.
- Provide for the decrementer register to be copied across on
migration.
- Various minor cleanups and bugfixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaYXViAAoJEJ2a6ncsY3GfDhgIAIDVBZH/Ftq7eJiUSxDpqyCQ
DF/x7fNKzK/J33pu+3ntOI2gZsldExAy7vH2M27I4qLIkbI5y3vu4v8l3CDlS1LK
9dKi72zg7baozoVF5mGUNm0B1sSvZiIQlC/kaami2aPTF1GcrJ561GthzfZwxENX
TSLqOA4LkeUZh2tUsvbcUrPi6v+E4Em2lgacQcx2ioMblWz56sZu79VsUbSSw/a3
P8+pIv7EbHw+TrOZMehjCbZkOdBeZ3IRLJsdlIAfe7y4vWME/5b9uVnQS/+XQj/B
6f3rQrduGvF2P6GMjsm8gDkgE5oZ1zbKlgO4i5WApnu80MMLFlfEUN+GWuGJ95Q=
=OjGs
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-next-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
PPC KVM update for 4.16
- Allow HPT guests to run on a radix host on POWER9 v2.2 CPUs
without requiring the complex thread synchronization that earlier
CPU versions required.
- A series from Ben Herrenschmidt to improve the handling of
escalation interrupts with the XIVE interrupt controller.
- Provide for the decrementer register to be copied across on
migration.
- Various minor cleanups and bugfixes.
Pull asm/uaccess.h whack-a-mole from Al Viro:
"It's linux/uaccess.h, damnit... Oh, well - eventually they'll stop
cropping up..."
* 'work.whack-a-mole' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
asm-prototypes.h: use linux/uaccess.h, not asm/uaccess.h
riscv: use linux/uaccess.h, not asm/uaccess.h...
ppc: for put_user() pull linux/uaccess.h, not asm/uaccess.h
When copying between the vcpu and svcpu, we may get scheduled away onto
a different host CPU which in turn means our svcpu pointer may change.
That means we need to atomically copy to and from the svcpu with preemption
disabled, so that all code around it always sees a coherent state.
Reported-by: Simon Guo <wei.guo.simon@gmail.com>
Fixes: 3d3319b45e ("KVM: PPC: Book3S: PR: Enable interrupts earlier")
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Running with CONFIG_DEBUG_ATOMIC_SLEEP reveals that HV KVM tries to
read guest memory, in order to emulate guest instructions, while
preempt is disabled and a vcore lock is held. This occurs in
kvmppc_handle_exit_hv(), called from post_guest_process(), when
emulating guest doorbell instructions on POWER9 systems, and also
when checking whether we have hit a hypervisor breakpoint.
Reading guest memory can cause a page fault and thus cause the
task to sleep, so we need to avoid reading guest memory while
holding a spinlock or when preempt is disabled.
To fix this, we move the preempt_enable() in kvmppc_run_core() to
before the loop that calls post_guest_process() for each vcore that
has just run, and we drop and re-take the vcore lock around the calls
to kvmppc_emulate_debug_inst() and kvmppc_emulate_doorbell_instr().
Dropping the lock is safe with respect to the iteration over the
runnable vcpus in post_guest_process(); for_each_runnable_thread
is actually safe to use locklessly. It is possible for a vcpu
to become runnable and add itself to the runnable_threads array
(code near the beginning of kvmppc_run_vcpu()) and then get included
in the iteration in post_guest_process despite the fact that it
has not just run. This is benign because vcpu->arch.trap and
vcpu->arch.ceded will be zero.
Cc: stable@vger.kernel.org # v4.13+
Fixes: 579006944e ("KVM: PPC: Book3S HV: Virtualize doorbell facility on POWER9")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Symbolic macros are unintuitive and hard to read, whereas octal constants
are much easier to interpret. Replace macros for the basic permission
flags (user/group/other read/write/execute) with numeric constants
instead, across the whole powerpc tree.
Introducing a significant number of changes across the tree for no runtime
benefit isn't exactly desirable, but so long as these macros are still
used in the tree people will keep sending patches that add them. Not only
are they hard to parse at a glance, there are multiple ways of coming to
the same value (as you can see with 0444 and 0644 in this patch) which
hurts readability.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Merge our fixes branch from the 4.15 cycle.
Unusually the fixes branch saw some significant features merged,
notably the RFI flush patches, so we want the code in next to be
tested against that, to avoid any surprises when the two are merged.
There's also some other work on the panic handling that was reverted
in fixes and we now want to do properly in next, which would conflict.
And we also fix a few other minor merge conflicts.
Merge the topic branch we share with kvm-ppc, this brings in two xive
commits, one from Paul to rework HMI handling, and a minor cleanup to
drop an unused flag.
Rename the paca->soft_enabled to paca->irq_soft_mask as it is no
longer used as a flag for interrupt state, but a mask.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a new ioctl, KVM_PPC_GET_CPU_CHAR, that gives userspace
information about the underlying machine's level of vulnerability
to the recently announced vulnerabilities CVE-2017-5715,
CVE-2017-5753 and CVE-2017-5754, and whether the machine provides
instructions to assist software to work around the vulnerabilities.
The ioctl returns two u64 words describing characteristics of the
CPU and required software behaviour respectively, plus two mask
words which indicate which bits have been filled in by the kernel,
for extensibility. The bit definitions are the same as for the
new H_GET_CPU_CHARACTERISTICS hypercall.
There is also a new capability, KVM_CAP_PPC_GET_CPU_CHAR, which
indicates whether the new ioctl is available.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This works on top of the single escalation support. When in single
escalation, with this change, we will keep the escalation interrupt
disabled unless the VCPU is in H_CEDE (idle). In any other case, we
know the VCPU will be rescheduled and thus there is no need to take
escalation interrupts in the host whenever a guest interrupt fires.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The prodded flag is only cleared at the beginning of H_CEDE,
so every time we have an escalation, we will cause the *next*
H_CEDE to return immediately.
Instead use a dedicated "irq_pending" flag to indicate that
a guest interrupt is pending for the VCPU. We don't reuse the
existing exception bitmap so as to avoid expensive atomic ops.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
That feature, provided by Power9 DD2.0 and later, when supported
by newer OPAL versions, allows us to sacrifice a queue (priority 7)
in favor of merging all the escalation interrupts of the queues
of a single VP into a single interrupt.
This reduces the number of host interrupts used up by KVM guests
especially when those guests use multiple priorities.
It will also enable a future change to control the masking of the
escalation interrupts more precisely to avoid spurious ones.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Add details about enabled queues and escalation interrupts.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This merges in the ppc-kvm topic branch of the powerpc tree to get
two patches which are prerequisites for the following patch series,
plus another patch which touches both powerpc and KVM code.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Hypervisor maintenance interrupts (HMIs) are generated by various
causes, signalled by bits in the hypervisor maintenance exception
register (HMER). In most cases calling OPAL to handle the interrupt
is the correct thing to do, but the "debug trigger" HMIs signalled by
PPC bit 17 (bit 46) of HMER are used to invoke software workarounds
for hardware bugs, and OPAL does not have any code to handle this
cause. The debug trigger HMI is used in POWER9 DD2.0 and DD2.1 chips
to work around a hardware bug in executing vector load instructions to
cache inhibited memory. In POWER9 DD2.2 chips, it is generated when
conditions are detected relating to threads being in TM (transactional
memory) suspended mode when the core SMT configuration needs to be
reconfigured.
The kernel currently has code to detect the vector CI load condition,
but only when the HMI occurs in the host, not when it occurs in a
guest. If a HMI occurs in the guest, it is always passed to OPAL, and
then we always re-sync the timebase, because the HMI cause might have
been a timebase error, for which OPAL would re-sync the timebase, thus
removing the timebase offset which KVM applied for the guest. Since
we don't know what OPAL did, we don't know whether to subtract the
timebase offset from the timebase, so instead we re-sync the timebase.
This adds code to determine explicitly what the cause of a debug
trigger HMI will be. This is based on a new device-tree property
under the CPU nodes called ibm,hmi-special-triggers, if it is
present, or otherwise based on the PVR (processor version register).
The handling of debug trigger HMIs is pulled out into a separate
function which can be called from the KVM guest exit code. If this
function handles and clears the HMI, and no other HMI causes remain,
then we skip calling OPAL and we proceed to subtract the guest
timebase offset from the timebase.
The overall handling for HMIs that occur in the host (i.e. not in a
KVM guest) is largely unchanged, except that we now don't set the flag
for the vector CI load workaround on DD2.2 processors.
This also removes a BUG_ON in the KVM code. BUG_ON is generally not
useful in KVM guest entry/exit code since it is difficult to handle
the resulting trap gracefully.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 chip versions starting with "Nimbus" v2.2 can support running
with some threads of a core in HPT mode and others in radix mode.
This means that we don't have to prohibit independent-threads mode
when running a HPT guest on a radix host, and we don't have to do any
of the synchronization between threads that was introduced in commit
c01015091a ("KVM: PPC: Book3S HV: Run HPT guests on POWER9 radix
hosts", 2017-10-19).
Rather than using up another CPU feature bit, we just do an
explicit test on the PVR (processor version register) at module
startup time to determine whether we have to take steps to avoid
having some threads in HPT mode and some in radix mode (so-called
"mixed mode"). We test for "Nimbus" (indicated by 0 or 1 in the top
nibble of the lower 16 bits) v2.2 or later, or "Cumulus" (indicated by
2 or 3 in that nibble) v1.1 or later.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
There are several cases outside the normal address space management
where a CPU's entire local TLB is to be flushed:
1. Booting the kernel, in case something has left stale entries in
the TLB (e.g., kexec).
2. Machine check, to clean corrupted TLB entries.
One other place where the TLB is flushed, is waking from deep idle
states. The flush is a side-effect of calling ->cpu_restore with the
intention of re-setting various SPRs. The flush itself is unnecessary
because in the first case, the TLB should not acquire new corrupted
TLB entries as part of sleep/wake (though they may be lost).
This type of TLB flush is coded inflexibly, several times for each CPU
type, and they have a number of problems with ISA v3.0B:
- The current radix mode of the MMU is not taken into account, it is
always done as a hash flushn For IS=2 (LPID-matching flush from host)
and IS=3 with HV=0 (guest kernel flush), tlbie(l) is undefined if
the R field does not match the current radix mode.
- ISA v3.0B hash must flush the partition and process table caches as
well.
- ISA v3.0B radix must flush partition and process scoped translations,
partition and process table caches, and also the page walk cache.
So consolidate the flushing code and implement it in C and inline asm
under the mm/ directory with the rest of the flush code. Add ISA v3.0B
cases for radix and hash, and use the radix flush in radix environment.
Provide a way for IS=2 (LPID flush) to specify the radix mode of the
partition. Have KVM pass in the radix mode of the guest.
Take out the flushes from early cputable/dt_cpu_ftrs detection hooks,
and move it later in the boot process after, the MMU registers are set
up and before relocation is first turned on.
The TLB flush is no longer called when restoring from deep idle states.
This was not be done as a separate step because booting secondaries
uses the same cpu_restore as idle restore, which needs the TLB flush.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves the code that loads and unloads the guest SLB values so that
it is done while the guest LPCR value is loaded in the LPCR register.
The reason for doing this is that on POWER9, the behaviour of the
slbmte instruction depends on the LPCR[UPRT] bit. If UPRT is 1, as
it is for a radix host (or guest), the SLB index is truncated to
2 bits. This means that for a HPT guest on a radix host, the SLB
was not being loaded correctly, causing the guest to crash.
The SLB is now loaded much later in the guest entry path, after the
LPCR is loaded, which for a secondary thread is after it sees that
the primary thread has switched the MMU to the guest. The loop that
waits for the primary thread has a branch out to the exit code that
is taken if it sees that other threads have commenced exiting the
guest. Since we have now not loaded the SLB at this point, we make
this path branch to a new label 'guest_bypass' and we move the SLB
unload code to before this label.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This fixes a bug where it is possible to enter a guest on a POWER9
system without having the XIVE (interrupt controller) context loaded.
This can happen because we unload the XIVE context from the CPU
before doing the real-mode handling for machine checks. After the
real-mode handler runs, it is possible that we re-enter the guest
via a fast path which does not load the XIVE context.
To fix this, we move the unloading of the XIVE context to come after
the real-mode machine check handler is called.
Fixes: 5af5099385 ("KVM: PPC: Book3S HV: Native usage of the XIVE interrupt controller")
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds a register identifier for use with the one_reg interface
to allow the decrementer expiry time to be read and written by
userspace. The decrementer expiry time is in guest timebase units
and is equal to the sum of the decrementer and the guest timebase.
(The expiry time is used rather than the decrementer value itself
because the expiry time is not constantly changing, though the
decrementer value is, while the guest vcpu is not running.)
Without this, a guest vcpu migrated to a new host will see its
decrementer set to some random value. On POWER8 and earlier, the
decrementer is 32 bits wide and counts down at 512MHz, so the
guest vcpu will potentially see no decrementer interrupts for up
to about 4 seconds, which will lead to a stall. With POWER9, the
decrementer is now 56 bits side, so the stall can be much longer
(up to 2.23 years) and more noticeable.
To help work around the problem in cases where userspace has not been
updated to migrate the decrementer expiry time, we now set the
default decrementer expiry at vcpu creation time to the current time
rather than the maximum possible value. This should mean an
immediate decrementer interrupt when a migrated vcpu starts
running. In cases where the decrementer is 32 bits wide and more
than 4 seconds elapse between the creation of the vcpu and when it
first runs, the decrementer would have wrapped around to positive
values and there may still be a stall - but this is no worse than
the current situation. In the large-decrementer case, we are sure
to get an immediate decrementer interrupt (assuming the time from
vcpu creation to first run is less than 2.23 years) and we thus
avoid a very long stall.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
One fix for an oops at boot if we take a hotplug interrupt before we are ready
to handle it.
The bulk is patches to implement mitigation for Meltdown, see the change logs
for more details.
Thanks to:
Nicholas Piggin, Michael Neuling, Oliver O'Halloran, Jon Masters, Jose Ricardo
Ziviani, David Gibson.
-----BEGIN PGP SIGNATURE-----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=UZHv
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.15-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"One fix for an oops at boot if we take a hotplug interrupt before we
are ready to handle it.
The bulk is patches to implement mitigation for Meltdown, see the
change logs for more details.
Thanks to: Nicholas Piggin, Michael Neuling, Oliver O'Halloran, Jon
Masters, Jose Ricardo Ziviani, David Gibson"
* tag 'powerpc-4.15-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv: Check device-tree for RFI flush settings
powerpc/pseries: Query hypervisor for RFI flush settings
powerpc/64s: Support disabling RFI flush with no_rfi_flush and nopti
powerpc/64s: Add support for RFI flush of L1-D cache
powerpc/64s: Convert slb_miss_common to use RFI_TO_USER/KERNEL
powerpc/64: Convert fast_exception_return to use RFI_TO_USER/KERNEL
powerpc/64: Convert the syscall exit path to use RFI_TO_USER/KERNEL
powerpc/64s: Simple RFI macro conversions
powerpc/64: Add macros for annotating the destination of rfid/hrfid
powerpc/pseries: Add H_GET_CPU_CHARACTERISTICS flags & wrapper
powerpc/pseries: Make RAS IRQ explicitly dependent on DLPAR WQ
Four commits here, including two that were tagged but never merged.
Three of them are for the HPT resizing code; two of those fix a
user-triggerable use-after-free in the host, and one that fixes
stale TLB entries in the guest. The remaining commit fixes a bug
causing PR KVM guests under PowerVM to fail to start.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaVfPgAAoJEJ2a6ncsY3GfA10IANZMkwtIpqxGlsAeXKr5bWdl
iXYD9ymb2/FOHBbg6v8Eh6Gb1ycjzXpXqn74/Y9TE4Ort7mdiH+W6kXYEsMqL8yg
7Uwnj8DuWFuFxX0x0V4SJQzgdCnOefVcfoo/RnLUzmLsW0Vqtr3A1djM5iHlxFvv
ntkNtGYPOoaHl6rjtfHTDfLWN/DzEJbaIU/0O1LIkBxPG4STzSXErAucLL46Pa/X
NuPO2HfpxQiacHVG62iy89eJeAcraEAXnH5e6eVPRQQqh3DSIERMU6n6jXyZeMU5
NWX8Qme3VGBpiJOiCGMvMrnJmQmMTSWTtkGljyaFy+vZWMqGZ6xJ3wIP+5t9d+Q=
=dw6K
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-fixes-4.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into kvm-master
PPC KVM fixes for 4.15
Four commits here, including two that were tagged but never merged.
Three of them are for the HPT resizing code; two of those fix a
user-triggerable use-after-free in the host, and one that fixes
stale TLB entries in the guest. The remaining commit fixes a bug
causing PR KVM guests under PowerVM to fail to start.
A headline should be quickly put into a sequence. Thus use the
function "seq_puts" instead of "seq_printf" for this purpose.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
On Book3S in HV mode, we don't use the vcpu->arch.dec field at all.
Instead, all logic is built around vcpu->arch.dec_expires.
So let's remove the one remaining piece of code that was setting it.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The KVM_PPC_ALLOCATE_HTAB ioctl(), implemented by kvmppc_alloc_reset_hpt()
is supposed to completely clear and reset a guest's Hashed Page Table (HPT)
allocating or re-allocating it if necessary.
In the case where an HPT of the right size already exists and it just
zeroes it, it forces a TLB flush on all guest CPUs, to remove any stale TLB
entries loaded from the old HPT.
However, that situation can arise when the HPT is resizing as well - or
even when switching from an RPT to HPT - so those cases need a TLB flush as
well.
So, move the TLB flush to trigger in all cases except for errors.
Cc: stable@vger.kernel.org # v4.10+
Fixes: f98a8bf9ee ("KVM: PPC: Book3S HV: Allow KVM_PPC_ALLOCATE_HTAB ioctl() to change HPT size")
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Commit 96df226 ("KVM: PPC: Book3S PR: Preserve storage control bits")
added code to preserve WIMG bits but it missed 2 special cases:
- a magic page in kvmppc_mmu_book3s_64_xlate() and
- guest real mode in kvmppc_handle_pagefault().
For these ptes, WIMG was 0 and pHyp failed on these causing a guest to
stop in the very beginning at NIP=0x100 (due to bd9166ffe "KVM: PPC:
Book3S PR: Exit KVM on failed mapping").
According to LoPAPR v1.1 14.5.4.1.2 H_ENTER:
The hypervisor checks that the WIMG bits within the PTE are appropriate
for the physical page number else H_Parameter return. (For System Memory
pages WIMG=0010, or, 1110 if the SAO option is enabled, and for IO pages
WIMG=01**.)
This hence initializes WIMG to non-zero value HPTE_R_M (0x10), as expected
by pHyp.
[paulus@ozlabs.org - fix compile for 32-bit]
Cc: stable@vger.kernel.org # v4.11+
Fixes: 96df226 "KVM: PPC: Book3S PR: Preserve storage control bits"
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Tested-by: Ruediger Oertel <ro@suse.de>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This commit does simple conversions of rfi/rfid to the new macros that
include the expected destination context. By simple we mean cases
where there is a single well known destination context, and it's
simply a matter of substituting the instruction for the appropriate
macro.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When we migrate a VM from a POWER8 host (XICS) to a POWER9 host
(XICS-on-XIVE), we have an error:
qemu-kvm: Unable to restore KVM interrupt controller state \
(0xff000000) for CPU 0: Invalid argument
This is because kvmppc_xics_set_icp() checks the new state
is internaly consistent, and especially:
...
1129 if (xisr == 0) {
1130 if (pending_pri != 0xff)
1131 return -EINVAL;
...
On the other side, kvmppc_xive_get_icp() doesn't set
neither the pending_pri value, nor the xisr value (set to 0)
(and kvmppc_xive_set_icp() ignores the pending_pri value)
As xisr is 0, pending_pri must be set to 0xff.
Fixes: 5af5099385 ("KVM: PPC: Book3S HV: Native usage of the XIVE interrupt controller")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When restoring a pending interrupt, we are setting the Q bit to force
a retrigger in xive_finish_unmask(). But we also need to force an EOI
in this case to reach the same initial state : P=1, Q=0.
This can be done by not setting 'old_p' for pending interrupts which
will inform xive_finish_unmask() that an EOI needs to be sent.
Fixes: 5af5099385 ("KVM: PPC: Book3S HV: Native usage of the XIVE interrupt controller")
Cc: stable@vger.kernel.org # v4.12+
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Tested-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
After the vcpu_load/vcpu_put pushdown, the handling of asynchronous VCPU
ioctl is already much clearer in that it is obvious that they bypass
vcpu_load and vcpu_put.
However, it is still not perfect in that the different state of the VCPU
mutex is still hidden in the caller. Separate those ioctls into a new
function kvm_arch_vcpu_async_ioctl that returns -ENOIOCTLCMD for more
"traditional" synchronous ioctls.
Cc: James Hogan <jhogan@kernel.org>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Suggested-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the calls to vcpu_load() and vcpu_put() in to the architecture
specific implementations of kvm_arch_vcpu_ioctl() which dispatches
further architecture-specific ioctls on to other functions.
Some architectures support asynchronous vcpu ioctls which cannot call
vcpu_load() or take the vcpu->mutex, because that would prevent
concurrent execution with a running VCPU, which is the intended purpose
of these ioctls, for example because they inject interrupts.
We repeat the separate checks for these specifics in the architecture
code for MIPS, S390 and PPC, and avoid taking the vcpu->mutex and
calling vcpu_load for these ioctls.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move vcpu_load() and vcpu_put() into the architecture specific
implementations of kvm_arch_vcpu_ioctl_set_guest_debug().
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move vcpu_load() and vcpu_put() into the architecture specific
implementations of kvm_arch_vcpu_ioctl_translate().
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move vcpu_load() and vcpu_put() into the architecture specific
implementations of kvm_arch_vcpu_ioctl_set_sregs().
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move vcpu_load() and vcpu_put() into the architecture specific
implementations of kvm_arch_vcpu_ioctl_get_sregs().
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move vcpu_load() and vcpu_put() into the architecture specific
implementations of kvm_arch_vcpu_ioctl_set_regs().
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move vcpu_load() and vcpu_put() into the architecture specific
implementations of kvm_arch_vcpu_ioctl_get_regs().
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move vcpu_load() and vcpu_put() into the architecture specific
implementations of kvm_arch_vcpu_ioctl_run().
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> # s390 parts
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
[Rebased. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When serving multiple resize requests following could happen:
CPU0 CPU1
---- ----
kvm_vm_ioctl_resize_hpt_prepare(1);
-> schedule_work()
/* system_rq might be busy: delay */
kvm_vm_ioctl_resize_hpt_prepare(2);
mutex_lock();
if (resize) {
...
release_hpt_resize();
}
... resize_hpt_prepare_work()
-> schedule_work() {
mutex_unlock() /* resize->kvm could be wrong */
struct kvm *kvm = resize->kvm;
mutex_lock(&kvm->lock); <<<< UAF
...
}
i.e. a second resize request with different order could be started by
kvm_vm_ioctl_resize_hpt_prepare(), causing the previous request to be
free()d when there's still an active worker thread which will try to
access it. This leads to a use after free in point marked with UAF on
the diagram above.
To prevent this from happening, instead of unconditionally releasing a
pre-existing resize structure from the prepare ioctl(), we check if
the existing structure has an in-progress worker. We do that by
checking if the resize->error == -EBUSY, which is safe because the
resize->error field is protected by the kvm->lock. If there is an
active worker, instead of releasing, we mark the structure as stale by
unlinking it from kvm_struct.
In the worker thread we check for a stale structure (with kvm->lock
held), and in that case abort, releasing the stale structure ourself.
We make the check both before and the actual allocation. Strictly,
only the check afterwards is needed, the check before is an
optimization: if the structure happens to become stale before the
worker thread is dispatched, rather than during the allocation, it
means we can avoid allocating then immediately freeing a potentially
substantial amount of memory.
This fixes following or similar host kernel crash message:
[ 635.277361] Unable to handle kernel paging request for data at address 0x00000000
[ 635.277438] Faulting instruction address: 0xc00000000052f568
[ 635.277446] Oops: Kernel access of bad area, sig: 11 [#1]
[ 635.277451] SMP NR_CPUS=2048 NUMA PowerNV
[ 635.277470] Modules linked in: xt_CHECKSUM iptable_mangle ipt_MASQUERADE
nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4
nf_defrag_ipv4 xt_conntrack nf_conntrack ipt_REJECT nf_reject_ipv4 tun bridge stp llc
ebtable_filter ebtables ip6table_filter ip6_tables iptable_filter nfsv3 nfs_acl nfs
lockd grace fscache kvm_hv kvm rpcrdma sunrpc ib_isert iscsi_target_mod ib_iser libiscsi
scsi_transport_iscsi ib_srpt target_core_mod ext4 ib_srp scsi_transport_srp
ib_ipoib mbcache jbd2 rdma_ucm ib_ucm ib_uverbs ib_umad rdma_cm ib_cm iw_cm ocrdma(T)
ib_core ses enclosure scsi_transport_sas sg shpchp leds_powernv ibmpowernv i2c_opal
i2c_core powernv_rng ipmi_powernv ipmi_devintf ipmi_msghandler ip_tables xfs
libcrc32c sr_mod sd_mod cdrom lpfc nvme_fc(T) nvme_fabrics nvme_core ipr nvmet_fc(T)
tg3 nvmet libata be2net crc_t10dif crct10dif_generic scsi_transport_fc ptp scsi_tgt
pps_core crct10dif_common dm_mirror dm_region_hash dm_log dm_mod
[ 635.278687] CPU: 40 PID: 749 Comm: kworker/40:1 Tainted: G
------------ T 3.10.0.bz1510771+ #1
[ 635.278782] Workqueue: events resize_hpt_prepare_work [kvm_hv]
[ 635.278851] task: c0000007e6840000 ti: c0000007e9180000 task.ti: c0000007e9180000
[ 635.278919] NIP: c00000000052f568 LR: c0000000009ea310 CTR: c0000000009ea4f0
[ 635.278988] REGS: c0000007e91837f0 TRAP: 0300 Tainted: G
------------ T (3.10.0.bz1510771+)
[ 635.279077] MSR: 9000000100009033 <SF,HV,EE,ME,IR,DR,RI,LE> CR: 24002022 XER:
00000000
[ 635.279248] CFAR: c000000000009368 DAR: 0000000000000000 DSISR: 40000000 SOFTE: 1
GPR00: c0000000009ea310 c0000007e9183a70 c000000001250b00 c0000007e9183b10
GPR04: 0000000000000000 0000000000000000 c0000007e9183650 0000000000000000
GPR08: c0000007ffff7b80 00000000ffffffff 0000000080000028 d00000000d2529a0
GPR12: 0000000000002200 c000000007b56800 c000000000120028 c0000007f135bb40
GPR16: 0000000000000000 c000000005c1e018 c000000005c1e018 0000000000000000
GPR20: 0000000000000001 c0000000011bf778 0000000000000001 fffffffffffffef7
GPR24: 0000000000000000 c000000f1e262e50 0000000000000002 c0000007e9180000
GPR28: c000000f1e262e4c c000000f1e262e50 0000000000000000 c0000007e9183b10
[ 635.280149] NIP [c00000000052f568] __list_add+0x38/0x110
[ 635.280197] LR [c0000000009ea310] __mutex_lock_slowpath+0xe0/0x2c0
[ 635.280253] Call Trace:
[ 635.280277] [c0000007e9183af0] [c0000000009ea310] __mutex_lock_slowpath+0xe0/0x2c0
[ 635.280356] [c0000007e9183b70] [c0000000009ea554] mutex_lock+0x64/0x70
[ 635.280426] [c0000007e9183ba0] [d00000000d24da04]
resize_hpt_prepare_work+0xe4/0x1c0 [kvm_hv]
[ 635.280507] [c0000007e9183c40] [c000000000113c0c] process_one_work+0x1dc/0x680
[ 635.280587] [c0000007e9183ce0] [c000000000114250] worker_thread+0x1a0/0x520
[ 635.280655] [c0000007e9183d80] [c00000000012010c] kthread+0xec/0x100
[ 635.280724] [c0000007e9183e30] [c00000000000a4b8] ret_from_kernel_thread+0x5c/0xa4
[ 635.280814] Instruction dump:
[ 635.280880] 7c0802a6 fba1ffe8 fbc1fff0 7cbd2b78 fbe1fff8 7c9e2378 7c7f1b78
f8010010
[ 635.281099] f821ff81 e8a50008 7fa52040 40de00b8 <e8be0000> 7fbd2840 40de008c
7fbff040
[ 635.281324] ---[ end trace b628b73449719b9d ]---
Cc: stable@vger.kernel.org # v4.10+
Fixes: b5baa68773 ("KVM: PPC: Book3S HV: KVM-HV HPT resizing implementation")
Signed-off-by: Serhii Popovych <spopovyc@redhat.com>
[dwg: Replaced BUG_ON()s with WARN_ONs() and reworded commit message
for clarity]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently the kvm_resize_hpt structure has two fields relevant to the
state of an ongoing resize: 'prepare_done', which indicates whether
the worker thread has completed or not, and 'error' which indicates
whether it was successful or not.
Since the success/failure isn't known until completion, this is
confusingly redundant. This patch consolidates the information into
just the 'error' value: -EBUSY indicates the worked is still in
progress, other negative values indicate (completed) failure, 0
indicates successful completion.
As a bonus this reduces size of struct kvm_resize_hpt by
__alignof__(struct kvm_hpt_info) and saves few bytes of code.
While there correct comment in struct kvm_resize_hpt which references
a non-existent semaphore (leftover from an early draft).
Assert with WARN_ON() in case of HPT allocation thread work runs more
than once for resize request or resize_hpt_allocate() returns -EBUSY
that is treated specially.
Change comparison against zero to make checkpatch.pl happy.
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Serhii Popovych <spopovyc@redhat.com>
[dwg: Changed BUG_ON()s to WARN_ON()s and altered commit message for
clarity]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
* PPC bugfix: HPT guests on a POWER9 radix host
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJaICi1AAoJEL/70l94x66DjvEIAIML/e9YX1YrJZi0rsB9cbm0
Le3o5b3wKxPrlZdnpOZQ2mVWubUQdiHMPGX6BkpgyiJWUchnbj5ql1gUf5S0i3jk
TOk6nae6DU94xBuboeqZJlmx2VfPY/fqzLWsX3HFHpnzRl4XvXL5o7cWguIxVcVO
yU6bPgbAXyXSBennLWZxC3aQ2Ojikr3uxZQpUZTAPOW5hFINpCKCpqJBMxsb67wq
rwI0cJhRl92mHpbe8qeNJhavqY5eviy9iPUaZrOW9P4yw1uqjTAjgsUc1ydiaZSV
rOHeKBOgVfY/KBaNJKyKySfuL1MJ+DLcQqm9RlGpKNpFIeB0vvSf0gtmmqIAXIk=
=kh2y
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
- x86 bugfixes: APIC, nested virtualization, IOAPIC
- PPC bugfix: HPT guests on a POWER9 radix host
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (26 commits)
KVM: Let KVM_SET_SIGNAL_MASK work as advertised
KVM: VMX: Fix vmx->nested freeing when no SMI handler
KVM: VMX: Fix rflags cache during vCPU reset
KVM: X86: Fix softlockup when get the current kvmclock
KVM: lapic: Fixup LDR on load in x2apic
KVM: lapic: Split out x2apic ldr calculation
KVM: PPC: Book3S HV: Fix migration and HPT resizing of HPT guests on radix hosts
KVM: vmx: use X86_CR4_UMIP and X86_FEATURE_UMIP
KVM: x86: Fix CPUID function for word 6 (80000001_ECX)
KVM: nVMX: Fix vmx_check_nested_events() return value in case an event was reinjected to L2
KVM: x86: ioapic: Preserve read-only values in the redirection table
KVM: x86: ioapic: Clear Remote IRR when entry is switched to edge-triggered
KVM: x86: ioapic: Remove redundant check for Remote IRR in ioapic_set_irq
KVM: x86: ioapic: Don't fire level irq when Remote IRR set
KVM: x86: ioapic: Fix level-triggered EOI and IOAPIC reconfigure race
KVM: x86: inject exceptions produced by x86_decode_insn
KVM: x86: Allow suppressing prints on RDMSR/WRMSR of unhandled MSRs
KVM: x86: fix em_fxstor() sleeping while in atomic
KVM: nVMX: Fix mmu context after VMLAUNCH/VMRESUME failure
KVM: nVMX: Validate the IA32_BNDCFGS on nested VM-entry
...
One commit here, that fixes a couple of bugs relating to the patch
series that enables HPT guests to run on a radix host on POWER9
systems. This patch series went upstream in the 4.15 merge window,
so no stable backport is required.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaGKSnAAoJEJ2a6ncsY3GfF7MIANLLhznEMrWq8jw4g95WsJU1
MkDGwp8kIdhIOM9HD6JRskoJZB5Mws2BWlQ5PSaVFxO6v6eUgNLaRb/UBxC1r7gU
1f9/8corY4BNkezSdJqTL7Xgp13KjTU726OwYAqCPEyCSPEc9ciMyeIgyZuv2dPa
Pju+u4tnA+9JJyskgNL+/ybOOZwVat91VmNUVRq29zP6+zo1tmIDxrQchy6Bqui/
7Wg298G+yjAkJ8ktQu69ACk+0oEBGUOcLUlraqGSr9auR+b0nJ1PAGCDRaONdwgE
+X+OE+t+UC6rU+coUXMwO+Id0X7HMdsLQd3066ODEtD55g8MIVZ126Wt8xDmj5o=
=GSTh
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-fixes-4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into kvm-master
PPC KVM fixes for 4.15
One commit here, that fixes a couple of bugs relating to the patch
series that enables HPT guests to run on a radix host on POWER9
systems. This patch series went upstream in the 4.15 merge window,
so no stable backport is required.
KVM API says for the signal mask you set via KVM_SET_SIGNAL_MASK, that
"any unblocked signal received [...] will cause KVM_RUN to return with
-EINTR" and that "the signal will only be delivered if not blocked by
the original signal mask".
This, however, is only true, when the calling task has a signal handler
registered for a signal. If not, signal evaluation is short-circuited for
SIG_IGN and SIG_DFL, and the signal is either ignored without KVM_RUN
returning or the whole process is terminated.
Make KVM_SET_SIGNAL_MASK behave as advertised by utilizing logic similar
to that in do_sigtimedwait() to avoid short-circuiting of signals.
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In an excess of caution, commit 6f63e81bda ("KVM: PPC: Book3S: Add
MMIO emulation for FP and VSX instructions", 2017-02-21) included
checks for the case that vcpu->arch.mmio_vsx_copy_nums is less than
zero, even though its type is u8. This causes a Coverity warning,
so we remove the check for < 0. We also adjust the associated
comment to be more accurate ("4 or less" rather than "less than 4").
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This corrects the test that determines whether a vcpu that has just
become able to run in the guest (e.g. it has just finished handling
a hypercall or hypervisor page fault) and whose virtual core is
already running somewhere as a "piggybacked" vcore can start
immediately or not. (A piggybacked vcore is one which is executing
along with another vcore as a result of dynamic micro-threading.)
Previously the test tried to lock the piggybacked vcore using
spin_trylock, which would always fail because the vcore was already
locked, and so the vcpu would have to wait until its vcore exited
the guest before it could enter.
In fact the vcpu can enter if its vcore is in VCORE_PIGGYBACK state
and not already exiting (or exited) the guest, so the test in
VCORE_PIGGYBACK state is basically the same as for VCORE_RUNNING
state.
Coverity detected this as a double unlock issue, which it isn't
because the spin_trylock would always fail. This will fix the
apparent double unlock as well.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This removes a statement that has no effect. It should have been
removed in commit 898b25b202 ("KVM: PPC: Book3S HV: Simplify dynamic
micro-threading code", 2017-06-22) along with the loop over the
piggy-backed virtual cores.
This issue was reported by Coverity.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This fixes a typo where the intent was to assign to 'j' in order to
skip some number of bits in the dirty bitmap for a guest. The effect
of the typo is benign since it means we just iterate through all the
bits rather than skipping bits which we know will be zero. This issue
was found by Coverity.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This fixes two errors that prevent a guest using the HPT MMU from
successfully migrating to a POWER9 host in radix MMU mode, or resizing
its HPT when running on a radix host.
The first bug was that commit 8dc6cca556 ("KVM: PPC: Book3S HV:
Don't rely on host's page size information", 2017-09-11) missed two
uses of hpte_base_page_size(), one in the HPT rehashing code and
one in kvm_htab_write() (which is used on the destination side in
migrating a HPT guest). Instead we use kvmppc_hpte_base_page_shift().
Having the shift count means that we can use left and right shifts
instead of multiplication and division in a few places.
Along the way, this adds a check in kvm_htab_write() to ensure that the
page size encoding in the incoming HPTEs is recognized, and if not
return an EINVAL error to userspace.
The second bug was that kvm_htab_write was performing some but not all
of the functions of kvmhv_setup_mmu(), resulting in the destination VM
being left in radix mode as far as the hardware is concerned. The
simplest fix for now is make kvm_htab_write() call
kvmppc_setup_partition_table() like kvmppc_hv_setup_htab_rma() does.
In future it would be better to refactor the code more extensively
to remove the duplication.
Fixes: 8dc6cca556 ("KVM: PPC: Book3S HV: Don't rely on host's page size information")
Fixes: 7a84084c60 ("KVM: PPC: Book3S HV: Set partition table rather than SDR1 on POWER9")
Reported-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Tested-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Common:
- Python 3 support in kvm_stat
- Accounting of slabs to kmemcg
ARM:
- Optimized arch timer handling for KVM/ARM
- Improvements to the VGIC ITS code and introduction of an ITS reset
ioctl
- Unification of the 32-bit fault injection logic
- More exact external abort matching logic
PPC:
- Support for running hashed page table (HPT) MMU mode on a host that
is using the radix MMU mode; single threaded mode on POWER 9 is
added as a pre-requisite
- Resolution of merge conflicts with the last second 4.14 HPT fixes
- Fixes and cleanups
s390:
- Some initial preparation patches for exitless interrupts and crypto
- New capability for AIS migration
- Fixes
x86:
- Improved emulation of LAPIC timer mode changes, MCi_STATUS MSRs, and
after-reset state
- Refined dependencies for VMX features
- Fixes for nested SMI injection
- A lot of cleanups
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJaDayXAAoJEED/6hsPKofo/3UH/3HvlcHt+ADTkCU1/iiKAs+i
0zngIOXIxgHDnV0ww6bV+Znww0BzTYgKCAXX76z603jdpDwG/pzQQcbLDF5ZoJnD
sQtF10gZinWaRsHlfbLqjrHGL2pGDHO1UKBKLJ0bAIyORPZBxs7i+VmrY/blnr9c
0wsybJ8RbvwAxjsDL5jeX/z4NehPupmKUc4Lf0eZdSHwVOf9sjn+MP6jJ0r2JcIb
D+zddPBiLStzN97t4gZpQsrlj3LKrDS+6hY+1TjSvlh+yHKFVFh58VhLm4DuDeb5
bYOAlWJ/gAWEzfvr5Ld+Nd7SqWWn/14logPkQ4gcU4BI/neAOzk4c6hJfCHl1nk=
=593n
-----END PGP SIGNATURE-----
Merge tag 'kvm-4.15-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Radim Krčmář:
"First batch of KVM changes for 4.15
Common:
- Python 3 support in kvm_stat
- Accounting of slabs to kmemcg
ARM:
- Optimized arch timer handling for KVM/ARM
- Improvements to the VGIC ITS code and introduction of an ITS reset
ioctl
- Unification of the 32-bit fault injection logic
- More exact external abort matching logic
PPC:
- Support for running hashed page table (HPT) MMU mode on a host that
is using the radix MMU mode; single threaded mode on POWER 9 is
added as a pre-requisite
- Resolution of merge conflicts with the last second 4.14 HPT fixes
- Fixes and cleanups
s390:
- Some initial preparation patches for exitless interrupts and crypto
- New capability for AIS migration
- Fixes
x86:
- Improved emulation of LAPIC timer mode changes, MCi_STATUS MSRs,
and after-reset state
- Refined dependencies for VMX features
- Fixes for nested SMI injection
- A lot of cleanups"
* tag 'kvm-4.15-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (89 commits)
KVM: s390: provide a capability for AIS state migration
KVM: s390: clear_io_irq() requests are not expected for adapter interrupts
KVM: s390: abstract conversion between isc and enum irq_types
KVM: s390: vsie: use common code functions for pinning
KVM: s390: SIE considerations for AP Queue virtualization
KVM: s390: document memory ordering for kvm_s390_vcpu_wakeup
KVM: PPC: Book3S HV: Cosmetic post-merge cleanups
KVM: arm/arm64: fix the incompatible matching for external abort
KVM: arm/arm64: Unify 32bit fault injection
KVM: arm/arm64: vgic-its: Implement KVM_DEV_ARM_ITS_CTRL_RESET
KVM: arm/arm64: Document KVM_DEV_ARM_ITS_CTRL_RESET
KVM: arm/arm64: vgic-its: Free caches when GITS_BASER Valid bit is cleared
KVM: arm/arm64: vgic-its: New helper functions to free the caches
KVM: arm/arm64: vgic-its: Remove kvm_its_unmap_device
arm/arm64: KVM: Load the timer state when enabling the timer
KVM: arm/arm64: Rework kvm_timer_should_fire
KVM: arm/arm64: Get rid of kvm_timer_flush_hwstate
KVM: arm/arm64: Avoid phys timer emulation in vcpu entry/exit
KVM: arm/arm64: Move phys_timer_emulate function
KVM: arm/arm64: Use kvm_arm_timer_set/get_reg for guest register traps
...
Non-highlights:
- Five fixes for the >128T address space handling, both to fix bugs in our
implementation and to bring the semantics exactly into line with x86.
Highlights:
- Support for a new OPAL call on bare metal machines which gives us a true NMI
(ie. is not masked by MSR[EE]=0) for debugging etc.
- Support for Power9 DD2 in the CXL driver.
- Improvements to machine check handling so that uncorrectable errors can be
reported into the generic memory_failure() machinery.
- Some fixes and improvements for VPHN, which is used under PowerVM to notify
the Linux partition of topology changes.
- Plumbing to enable TM (transactional memory) without suspend on some Power9
processors (PPC_FEATURE2_HTM_NO_SUSPEND).
- Support for emulating vector loads form cache-inhibited memory, on some
Power9 revisions.
- Disable the fast-endian switch "syscall" by default (behind a CONFIG), we
believe it has never had any users.
- A major rework of the API drivers use when initiating and waiting for long
running operations performed by OPAL firmware, and changes to the
powernv_flash driver to use the new API.
- Several fixes for the handling of FP/VMX/VSX while processes are using
transactional memory.
- Optimisations of TLB range flushes when using the radix MMU on Power9.
- Improvements to the VAS facility used to access coprocessors on Power9, and
related improvements to the way the NX crypto driver handles requests.
- Implementation of PMEM_API and UACCESS_FLUSHCACHE for 64-bit.
Thanks to:
Alexey Kardashevskiy, Alistair Popple, Allen Pais, Andrew Donnellan, Aneesh
Kumar K.V, Arnd Bergmann, Balbir Singh, Benjamin Herrenschmidt, Breno Leitao,
Christophe Leroy, Christophe Lombard, Cyril Bur, Frederic Barrat, Gautham R.
Shenoy, Geert Uytterhoeven, Guilherme G. Piccoli, Gustavo Romero, Haren
Myneni, Joel Stanley, Kamalesh Babulal, Kautuk Consul, Markus Elfring, Masami
Hiramatsu, Michael Bringmann, Michael Neuling, Michal Suchanek, Naveen N. Rao,
Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Pedro Miraglia Franco de
Carvalho, Philippe Bergheaud, Sandipan Das, Seth Forshee, Shriya, Stephen
Rothwell, Stewart Smith, Sukadev Bhattiprolu, Tyrel Datwyler, Vaibhav Jain,
Vaidyanathan Srinivasan, William A. Kennington III.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Rq81
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"A bit of a small release, I suspect in part due to me travelling for
KS. But my backlog of patches to review is smaller than usual, so I
think in part folks just didn't send as much this cycle.
Non-highlights:
- Five fixes for the >128T address space handling, both to fix bugs
in our implementation and to bring the semantics exactly into line
with x86.
Highlights:
- Support for a new OPAL call on bare metal machines which gives us a
true NMI (ie. is not masked by MSR[EE]=0) for debugging etc.
- Support for Power9 DD2 in the CXL driver.
- Improvements to machine check handling so that uncorrectable errors
can be reported into the generic memory_failure() machinery.
- Some fixes and improvements for VPHN, which is used under PowerVM
to notify the Linux partition of topology changes.
- Plumbing to enable TM (transactional memory) without suspend on
some Power9 processors (PPC_FEATURE2_HTM_NO_SUSPEND).
- Support for emulating vector loads form cache-inhibited memory, on
some Power9 revisions.
- Disable the fast-endian switch "syscall" by default (behind a
CONFIG), we believe it has never had any users.
- A major rework of the API drivers use when initiating and waiting
for long running operations performed by OPAL firmware, and changes
to the powernv_flash driver to use the new API.
- Several fixes for the handling of FP/VMX/VSX while processes are
using transactional memory.
- Optimisations of TLB range flushes when using the radix MMU on
Power9.
- Improvements to the VAS facility used to access coprocessors on
Power9, and related improvements to the way the NX crypto driver
handles requests.
- Implementation of PMEM_API and UACCESS_FLUSHCACHE for 64-bit.
Thanks to: Alexey Kardashevskiy, Alistair Popple, Allen Pais, Andrew
Donnellan, Aneesh Kumar K.V, Arnd Bergmann, Balbir Singh, Benjamin
Herrenschmidt, Breno Leitao, Christophe Leroy, Christophe Lombard,
Cyril Bur, Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven,
Guilherme G. Piccoli, Gustavo Romero, Haren Myneni, Joel Stanley,
Kamalesh Babulal, Kautuk Consul, Markus Elfring, Masami Hiramatsu,
Michael Bringmann, Michael Neuling, Michal Suchanek, Naveen N. Rao,
Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Pedro Miraglia
Franco de Carvalho, Philippe Bergheaud, Sandipan Das, Seth Forshee,
Shriya, Stephen Rothwell, Stewart Smith, Sukadev Bhattiprolu, Tyrel
Datwyler, Vaibhav Jain, Vaidyanathan Srinivasan, and William A.
Kennington III"
* tag 'powerpc-4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (151 commits)
powerpc/64s: Fix Power9 DD2.0 workarounds by adding DD2.1 feature
powerpc/64s: Fix masking of SRR1 bits on instruction fault
powerpc/64s: mm_context.addr_limit is only used on hash
powerpc/64s/radix: Fix 128TB-512TB virtual address boundary case allocation
powerpc/64s/hash: Allow MAP_FIXED allocations to cross 128TB boundary
powerpc/64s/hash: Fix fork() with 512TB process address space
powerpc/64s/hash: Fix 128TB-512TB virtual address boundary case allocation
powerpc/64s/hash: Fix 512T hint detection to use >= 128T
powerpc: Fix DABR match on hash based systems
powerpc/signal: Properly handle return value from uprobe_deny_signal()
powerpc/fadump: use kstrtoint to handle sysfs store
powerpc/lib: Implement UACCESS_FLUSHCACHE API
powerpc/lib: Implement PMEM API
powerpc/powernv/npu: Don't explicitly flush nmmu tlb
powerpc/powernv/npu: Use flush_all_mm() instead of flush_tlb_mm()
powerpc/powernv/idle: Round up latency and residency values
powerpc/kprobes: refactor kprobe_lookup_name for safer string operations
powerpc/kprobes: Blacklist emulate_update_regs() from kprobes
powerpc/kprobes: Do not disable interrupts for optprobes and kprobes_on_ftrace
powerpc/kprobes: Disable preemption before invoking probe handler for optprobes
...
This rearranges the code in kvmppc_run_vcpu() and kvmppc_run_vcpu_hv()
to be neater and clearer. Deeply indented code in kvmppc_run_vcpu()
is moved out to a helper function, kvmhv_setup_mmu(). In
kvmppc_vcpu_run_hv(), make use of the existing variable 'kvm' in
place of 'vcpu->kvm'.
No functional change.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This merges in a couple of fixes from the kvm-ppc-fixes branch that
modify the same areas of code as some commits from the kvm-ppc-next
branch, in order to resolve the conflicts.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Just one fix here for a host crash that can occur with HV KVM
as a result of resizing the guest hashed page table (HPT).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaApLVAAoJEJ2a6ncsY3GfNfcIAJk93C9FK6k2urAORP3lDmKy
P6a4LnkMrQTuUCBGrkP4F1hGq2vpH6o/KeoEdhAgLMHHsarzMyBc5N7rHMHgZUzI
bUna0LaXtjdb5IP0kcDb8HmulmBaFiMf+sa2i3dIW3sCxtvqzzmxOluR0C29fG1I
gTdJV0XDzhQHJLixcQ3i4pi/K6b+wzXrY7fFPMpI2Wji6cKYr0ZL0fG8bQ0pV4OZ
0YgV9sR8mVN17JKU9R4GYz9fkp3+cXDG4xBVtczDlK6TJzF2XVUGgY/iJLMAyDRw
9gcEiIc+khkqyfuQt8iYBiHqRJ7HiT4yX1LMI9dM2vTZi23zsG3yTmsIc16QZLg=
=MzO/
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-fixes-4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
PPC KVM fixes for 4.14
Just one fix here for a host crash that can occur with HV KVM
as a result of resizing the guest hashed page table (HPT).
