FW starts using legacy power table command (0x77) for device wide power
settings. Currently this command contains only option flags field.
It can configure the following: CAM (Continuous Active Mode) and
POWER_SAVE_ENABLE debug option. Send this command when firmware is
loaded - D0 and D3.
Note: Setting this command is important to avoid unwanted FW behavior.
It particularly fixes a bug when a device does not drop to low power
after disassociation from AP.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adjust the following:
- RX/TX AP-to-PSM timeout in case of uAPSD and PBW snoozing
- PSM-to-AM TX/RX heavy traffic thresholds
- Beacon abort escape timer for D3/D0i3
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Performance Based Window snooze mechanism is based on uAPSD and is
used in low-medium traffic scenarios, in order to provide better power
performance while insuring low latency and jitter for the incoming traffic.
This patch enables PBW snoozing in case uAPSD is enabled and all ACs are
uAPSD trigger and delivery enabled.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement basic uAPSD client support adding the following:
- Advertise uAPSD support in HW capabilities
- Set all ACs trigger- and delivery-enabled
- Set max SP length to 2 buffered frames
- Assign QNDP with the highest TID with no mandatory admission
control required
- Set uAPSD related parameters in Power Table command
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set beacon abort escape timer values - 6 beacons in D0 state,
9 beacons in D3 and D0i3.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change beacon filtering command due to a change in the API.
In case the FW supports the old API, we do not send the
BF HCMD and assume that since the corresponding struct in
the FW is zeroed by default then we don't need to disable
it in the FW actively.
Signed-off-by: Hila Gonen <hila.gonen@intel.com>
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change power management implementation to support new host-device API
containing uAPSD parameters. Verify FW support for this new API.
Use the new power table command (0xA9) to configure power management.
Use the legacy command (0x77) if FW does not support the new API.
New file power_legacy.c is introduced for legacy implementation.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To improve power consumption in idle associated mode FW may lower
RX power. This low linearity mode is acceptable for listening low rate
RX such as beacons and groupcast. The driver enables LPRX only if PM
is enabled and associated AP's beacon TX rate is 1Mbps or 6Mbps.
LPRX RSSI threshold is used to limit a range where LPRX is applied.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If skip over DTIMs is enabled the driver can specify number of DTIMs
to skip. This parameter in host-device API implies number of DTIM
periods to skip. For example, to skip one DTIM means sleep over two
DTIM periods. Change semantics accordingly. Change this parameter's
default value.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beacon abort is used by device to increase idle dwell time when system
is idle. This algorithm is on top of beacon filtering feature. Enable
beacon abort only if power management is enabled.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
New host-device API provides the ability to set the number
of DTIMs to skip. Add this parameter to the command and set
it (to a sane default value.)
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware starts sending nulldata frames for keepalive immediately
after association, regardless of power management state. The driver
thus needs to configure keep alive period unconditionally.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Replace SLEEP_OVER_DTIM by SKIP_OVER_DTIM.
Add iwl_mvm prefix to a function name.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Current available FW still doesn't support new PM API.
Therefore, to enable basic power management with the
existing firmware, change the API in the driver back
to the API used in the current firmware.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
7000.c was released as GPL only by mistake: it should be
dual licensed - GPL / BSD.
The file that contains the license in the kernel is COPYING
and not LICENSE.GPL.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Newer firmware revisions have a completely new
firmware API. This is the new driver for this
new API.
I've listed the people who directly contributed
code, but many others from various teams have
contributed in other ways.
Cc: Alexander Bondar <alexander.bondar@intel.com>
Cc: Amit Beka <amit.beka@intel.com>
Cc: Amnon Paz <amnonx.paz@intel.com>
Cc: Assaf Krauss <assaf.krauss@intel.com>
Cc: David Spinadel <david.spinadel@intel.com>
Cc: Dor Shaish <dor.shaish@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Eytan Lifshitz <eytan.lifshitz@intel.com>
Cc: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
