Up to now ili9320_remove() returns zero unconditionally. Make it return
void instead which makes it easier to see in the callers that there is
no error to handle.
Also the return value of spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211019120927.3822792-1-u.kleine-koenig@pengutronix.de
backlight.h documents "struct backlight_ops->get_brightness()" to return
a negative errno on failure.
So far these errors have not been handled in the backlight core.
This leads to negative values being exposed through sysfs although only
positive values are documented to be reported.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The note in c2adda27d2 ("video: backlight: Add of_find_backlight helper
in backlight.c") says that gpio-backlight uses brightness as power state.
This has been fixed since in ec665b756e ("backlight: gpio-backlight:
Correct initial power state handling") and other backlight drivers do not
require this workaround. Drop the workaround.
This fixes the case where e.g. pwm-backlight can perfectly well be set to
brightness 0 on boot in DT, which without this patch leads to the display
brightness to be max instead of off.
Fixes: c2adda27d2 ("video: backlight: Add of_find_backlight helper in backlight.c")
Cc: <stable@vger.kernel.org> # 5.4+
Cc: <stable@vger.kernel.org> # 4.19.x: ec665b756e: backlight: gpio-backlight: Correct initial power state handling
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently there are (at least) two problems in the way pwm_bl starts
managing the enable_gpio pin. Both occur when the backlight is initially
off and the driver finds the pin not already in output mode and, as a
result, unconditionally switches it to output-mode and asserts the signal.
Problem 1: This could cause the backlight to flicker since, at this stage
in driver initialisation, we have no idea what the PWM and regulator are
doing (an unconfigured PWM could easily "rest" at 100% duty cycle).
Problem 2: This will cause us not to correctly honour the
post_pwm_on_delay (which also risks flickers).
Fix this by moving the code to configure the GPIO output mode until after
we have examines the handover state. That allows us to initialize
enable_gpio to off if the backlight is currently off and on if the
backlight is on.
Cc: stable@vger.kernel.org
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove interrupt disablement during backlight setting. It is
way to dangerous and makes platforms instable by having it
miss vblank IRQs leading to the graphics derailing.
The code is using ndelay() which is not available on
platforms such as ARM and will result in 32 * udelay(1)
which is substantial.
Add some code to detect if an interrupt occurs during the
tight loop and in that case just redo it from the top.
Fixes: 5317f37e48 ("backlight: Add Kinetic KTD253 backlight driver")
Cc: Stephan Gerhold <stephan@gerhold.net>
Reported-by: newbyte@disroot.org
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The practical upside here is that this only needs a single API call to
program the hardware which (depending on the underlaying hardware) can
be more effective and prevents glitches.
Up to now the return value of the pwm functions was ignored. Fix this
and propagate the error to the caller.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
According to <linux/backlight.h> .update_status() is supposed to
return 0 on success and a negative error code otherwise. Adapt
lm3630a_bank_a_update_status() and lm3630a_bank_b_update_status() to
actually do it.
While touching that also add the error code to the failure message.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove leading whitespaces, replace multi spaces with tabs, and fix help
text indentation.
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add a compatible for PMI8994 WLED. It uses the V4 of WLED IP.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Adds support for Richtek RT4831 backlight.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
device_for_each_child_node() bumps a reference counting of a returned variable.
We have to balance it whenever we return to the caller.
Cc: Brian Masney <masneyb@onstation.org>
Cc: Dan Murphy <dmurphy@ti.com>
Fixes: 8fbce8efe1 ("backlight: lm3630a: Add firmware node support")
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
With gcc-11, we get a warning about code that looks correct
but badly indented:
drivers/video/backlight/jornada720_bl.c: In function ‘jornada_bl_update_status’:
drivers/video/backlight/jornada720_bl.c:66:11: error: this ‘else’ clause does not guard... [-Werror=misleading-indentation]
66 | } else /* turn on backlight */
| ^~~~
Change the formatting according to our normal conventions.
Fixes: 13a7b5dc0d ("backlight: Adds HP Jornada 700 series backlight driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As per the current implementation, after FSC (Full Scale Current)
and brightness update the sync bits are set-then-cleared.
But, the FSC and brightness sync takes place when the sync bits are
set (e.g. on a rising edge). So the hardware team recommends a
clear-then-set approach in order to guarantee such a transition
regardless of the previous register state.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently, for WLED5, the FSC (Full scale current) setting is not
updated properly due to driver toggling the wrong register after
an FSC update.
On WLED5 we should only toggle the MOD_SYNC bit after a brightness
update. For an FSC update we need to toggle the SYNC bits instead.
Fix it by adopting the common wled3_sync_toggle() for WLED5 and
introducing new code to the brightness update path to compensate.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The KTD259 works just like KTD253 so add this compatible
to the driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
WLED3_SINK_REG_SYNC is, as the name implies, a sink register offset.
Therefore, use the sink address as base instead of the ctrl address.
This fixes the sync toggle on wled4, which can be observed by the fact
that adjusting brightness now works.
It has no effect on wled3 because sink and ctrl base addresses are the
same. This allows adjusting the brightness without having to disable
then reenable the module.
Signed-off-by: Obeida Shamoun <oshmoun100@googlemail.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Kiran Gunda <kgunda@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- Generalise byte swapping assembly
- Update debug addresses for STI
- Validate start of physical memory with DTB
- Do not clear SCTLR.nTLSMD in decompressor
- amba/locomo/sa1111 devices remove method return type is void
- address markers for KASAN in page table dump
-----BEGIN PGP SIGNATURE-----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=BULT
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- Generalise byte swapping assembly
- Update debug addresses for STI
- Validate start of physical memory with DTB
- Do not clear SCTLR.nTLSMD in decompressor
- amba/locomo/sa1111 devices remove method return type is void
- address markers for KASAN in page table dump
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9065/1: OABI compat: fix build when EPOLL is not enabled
ARM: 9055/1: mailbox: arm_mhuv2: make remove callback return void
amba: Make use of bus_type functions
amba: Make the remove callback return void
vfio: platform: simplify device removal
amba: reorder functions
amba: Fix resource leak for drivers without .remove
ARM: 9054/1: arch/arm/mm/mmu.c: Remove duplicate header
ARM: 9053/1: arm/mm/ptdump:Add address markers for KASAN regions
ARM: 9051/1: vdso: remove unneded extra-y addition
ARM: 9050/1: Kconfig: Select ARCH_HAVE_NMI_SAFE_CMPXCHG where possible
ARM: 9049/1: locomo: make locomo bus's remove callback return void
ARM: 9048/1: sa1111: make sa1111 bus's remove callback return void
ARM: 9047/1: smp: remove unused variable
ARM: 9046/1: decompressor: Do not clear SCTLR.nTLSMD for ARMv7+ cores
ARM: 9045/1: uncompress: Validate start of physical memory against passed DTB
ARM: 9042/1: debug: no uncompress debugging while semihosting
ARM: 9041/1: sti LL_UART: add STiH418 SBC UART0 support
ARM: 9040/1: use DEBUG_UART_PHYS and DEBUG_UART_VIRT for sti LL_UART
ARM: 9039/1: assembler: generalize byte swapping macro into rev_l
Use getter and setter functions, for platform_device structures and a
spi_device structure.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The KTD253 backlight might already be on when the driver
is probed: then we don't really know what the current
ratio is and all light intensity settings will be off
relative to what it was at boot.
To fix this, bring up the backlight OFF then move it to
the default backlight from there so we know the state.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver core ignores the return value of struct bus_type::remove
because there is only little that can be done. To simplify the quest to
make this function return void, let struct locomo_driver::remove return
void, too. All users already unconditionally return 0, this commit makes
it obvious that returning an error code is a bad idea and ensures future
users behave accordingly.
Link: https://lore.kernel.org/r/20201126110140.2021758-1-u.kleine-koenig@pengutronix.de
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This converts the lms283gf05 backlight driver to use GPIO
descriptors and switches the single PXA Palm Z2 device
over to defining these.
Since the platform data was only used to convey GPIO
information we can delete the platform data header.
Notice that we define the proper active low semantics in
the board file GPIO descriptor table (active low) and
assert the reset line by bringing it to "1" (asserted).
Cc: Marek Vasut <marex@denx.de>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Mack <daniel@zonque.org>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The previous behavior was a little unexpected, its properties/problems:
1. It was designed to generate strictly increasing values (no repeats)
2. It had quantization errors when calculating step size. Resulting in
unexpected jumps near the end of some segments.
Example settings:
brightness-levels = <0 1 2 4 8 16 32 64 128 256>;
num-interpolated-steps = <16>;
Whenever num-interpolated-steps was larger than the distance
between 2 consecutive brightness levels the table would get really
discontinuous. The slope of the interpolation would stick with
integers only and if it was 0 the whole line segment would get skipped.
The distances between 1 2 4 and 8 would be 1 (property #1 fighting us),
and only starting with 16 it would start to interpolate properly.
Property #1 is not enough. The goal here is more than just monotonically
increasing. We should still care about the shape of the curve. Repeated
points might be desired if we're in the part of the curve where we want
to go slow (aka slope near 0).
Problem #2 is plainly a bug. Imagine if the 64 entry was 63 instead,
the calculated slope on the 32-63 segment will be almost half as it
should be.
The most expected and simplest algorithm for interpolation is linear
interpolation, which would handle both problems.
Let's just implement that!
Take pairs of points from the brightness-levels array and linearly
interpolate between them. On the X axis (what userspace sees) we'll
now have equally sized intervals (num-interpolated-steps sized,
as opposed to before where we were at the mercy of quantization).
Signed-off-by: Alexandru Stan <amstan@chromium.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Tosa backlight driver was converted to use GPIO descriptors
in 0b0cb52bd8
("video: backlight: tosa: Use GPIO lookup table") but
still includes <linux/gpio.h> rather than <linux/gpio/consumer.h>.
Fix it.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Tosa backlight LCDE driver was converted to use GPIO descriptors
in 0b0cb52bd8
("video: backlight: tosa: Use GPIO lookup table") but
still includes <linux/gpio.h> rather than <linux/gpio/consumer.h>.
Fix it.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kinetic KTD253 backlight driver is controlled with a
single GPIO line, but still supports a range of brightness
settings by sending fast pulses on the line.
This is based off the source code release for the Samsung
GT-S7710 mobile phone.
Cc: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When of_property_read_u32_array() returns an error code, a
pairing refcount decrement is needed to keep np's refcount
balanced.
Fixes: f705806c9f ("backlight: Add support Skyworks SKY81452 backlight driver")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The majority of this batch is conversion of the PWM period and duty
cycle to 64-bit unsigned integers, which is required so that some types
of hardware can generate the full range of signals that they're capable
of. The remainder is mostly minor fixes and cleanups.
-----BEGIN PGP SIGNATURE-----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=v6MG
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"The majority of this batch is conversion of the PWM period and duty
cycle to 64-bit unsigned integers, which is required so that some
types of hardware can generate the full range of signals that they're
capable of.
The remainder is mostly minor fixes and cleanups"
* tag 'pwm/for-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: bcm-iproc: handle clk_get_rate() return
pwm: Replace HTTP links with HTTPS ones
pwm: omap-dmtimer: Repair pwm_omap_dmtimer_chip's broken kerneldoc header
pwm: mediatek: Provide missing kerneldoc description for 'soc' arg
pwm: bcm-kona: Remove impossible comparison when validating duty cycle
pwm: bcm-iproc: Remove impossible comparison when validating duty cycle
pwm: iqs620a: Use lowercase hexadecimal literals for consistency
pwm: Convert period and duty cycle to u64
clk: pwm: Use 64-bit division function
backlight: pwm_bl: Use 64-bit division function
pwm: sun4i: Use nsecs_to_jiffies to avoid a division
pwm: sifive: Use 64-bit division macro
pwm: iqs620a: Use 64-bit division
pwm: imx27: Use 64-bit division macro
pwm: imx-tpm: Use 64-bit division macro
pwm: clps711x: Use 64-bit division macro
hwmon: pwm-fan: Use 64-bit division macro
drm/i915: Use 64-bit division macro
There are no external users of of_find_backlight, as they have all
changed to use the managed version. Make of_find_backlight static to
prevent new external users.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are no external users of backlight_put(). Drop it and open code
the two users in backlight.c.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Introduce the backlight_get_brightness() helper in all
video/backlight/* drivers. This simplifies the code and align the
implementation of the update_status() operation across the different
backlight drivers.
Some of the drivers gains a little extra functionality by the change
as they now respect the fb_blank() ioctl.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the backlight_is_blank() helper to simplify the code a bit.
The jornada720_bl driver distinguish between backlight off
and brightness set to 0.
Thus this driver turn off backlight only when backlight_is_blank()
returns true.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Introduce the use of backlight_get_brightness() to simplify the
update_status() operation. With the simpler implementation drop the
gpio_backlight_get_next_brightness() helper as it was now a
one-liner.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
cr_bllcd can turn backlight ON or OFF.
Fix semantitics so they equals what we know from gpio-backlight.
brightness == 0 => backlight off
brightness == 1 => backlight on
Use the backlight_get_brightness() helper to simplify the code.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Replaces the open-coded checks of the state, with the
backlight_get_brightness() helper. This increases readability of the
code and align the functionality across the drivers.
Furthermore drop the debug prints in update_status().
If we need debug printing then we can add it to the backlight core.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add overview chapter to backlight.c.
Update existing kernel-doc to follow a more consistent style and drop
kernel-doc for deprecated functions.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The backlight_bl driver required initialization using
struct generic_bl_info. As there are no more references
to this struct there is no users left.
So it is safe to delete the driver.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Increase readability of fb_notifier_callback() by removing
a few indent levels.
No functional change.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Firstly, all lines must begin with a '*'. Secondly, arg descriptions
must be spelt correctly, so fix misspelling of 'gpioD_enable' and
'short_detecTion_threshold'
Fixes the following W=1 kernel build warning(s):
drivers/video/backlight/sky81452-backlight.c:46: warning: bad line: If it is not defined, default name is lcd-backlight.
drivers/video/backlight/sky81452-backlight.c:64: warning: Function parameter or member 'gpiod_enable' not described in 'sky81452_bl_platform_data'
drivers/video/backlight/sky81452-backlight.c:64: warning: Function parameter or member 'short_detection_threshold' not described in 'sky81452_bl_platform_data'
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixes W=1 warnings:
drivers/video/backlight/qcom-wled.c:1294:34: warning: ‘wled4_string_cfg’ defined but not used [-Wunused-const-variable=]
1294 | static const struct wled_var_cfg wled4_string_cfg = {
| ^~~~~~~~~~~~~~~~
drivers/video/backlight/qcom-wled.c:1290:34: warning: ‘wled3_string_cfg’ defined but not used [-Wunused-const-variable=]
1290 | static const struct wled_var_cfg wled3_string_cfg = {
| ^~~~~~~~~~~~~~~~
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
unsigned ints 'sources' and 'bank' cannot be less than LM3630A_SINK_0 (0)
and LM3630A_BANK_0 (0) respecitively, so change the logic to only check
for thier two possible valid values.
Fixes W=1 warnings:
drivers/video/backlight/lm3630a_bl.c: In function ‘lm3630a_parse_led_sources’:
drivers/video/backlight/lm3630a_bl.c:394:18: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
394 | if (sources[i] < LM3630A_SINK_0 || sources[i] > LM3630A_SINK_1)
| ^
drivers/video/backlight/lm3630a_bl.c: In function ‘lm3630a_parse_bank’:
drivers/video/backlight/lm3630a_bl.c:415:11: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
415 | if (bank < LM3630A_BANK_0 || bank > LM3630A_BANK_1)
| ^
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Daniel Jeong <gshark.jeong@gmail.com>
Cc: LDD MLP <ldd-mlp@list.ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Kerneldoc syntax is used, but not complete. Descriptions required.
Prevents warnings like:
drivers/video/backlight/backlight.c:329: warning: Function parameter or member 'reason' not described in 'backlight_force_update'
drivers/video/backlight/backlight.c:354: warning: Function parameter or member 'props' not described in 'backlight_device_register'
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Jamey Hicks <jamey.hicks@hp.com>
Cc: Andrew Zabolotny <zap@homelink.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Kerneldoc syntax is used, but not complete. Descriptions required.
Prevents warnings like:
drivers/video/backlight/ili922x.c:298: warning: Function parameter or member 'spi' not described in 'ili922x_reg_dump'
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Software Engineering <sbabic@denx.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Kerneldoc is for documenting function arguments and return values.
Prevents warnings like:
drivers/video/backlight/ili922x.c:127: warning: cannot understand function prototype: 'int ili922x_id = 1; '
drivers/video/backlight/ili922x.c:136: warning: cannot understand function prototype: 'struct ili922x '
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Software Engineering <sbabic@denx.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Kerneldoc syntax is used, but not complete. Descriptions required.
Prevents warnings like:
drivers/video/backlight/ili922x.c:116: warning: Function parameter or member 's' not described in 'CHECK_FREQ_REG'
drivers/video/backlight/ili922x.c:116: warning: Function parameter or member 'x' not described in 'CHECK_FREQ_REG'
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Software Engineering <sbabic@denx.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This has been missing since the conversion to 'struct device' in 2007.
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Jamey Hicks <jamey.hicks@hp.com>
Cc: Andrew Zabolotny <zap@homelink.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
