Pull ucounts fixes from Eric Biederman:
"There has been one very hard to track down bug in the ucount code that
we have been tracking since roughly v5.14 was released. Alex managed
to find a reliable reproducer a few days ago and then I was able to
instrument the code and figure out what the issue was.
It turns out the sigqueue_alloc single atomic operation optimization
did not play nicely with ucounts multiple level rlimits. It turned out
that either sigqueue_alloc or sigqueue_free could be operating on
multiple levels and trigger the conditions for the optimization on
more than one level at the same time.
To deal with that situation I have introduced inc_rlimit_get_ucounts
and dec_rlimit_put_ucounts that just focuses on the optimization and
the rlimit and ucount changes.
While looking into the big bug I found I couple of other little issues
so I am including those fixes here as well.
When I have time I would very much like to dig into process ownership
of the shared signal queue and see if we could pick a single owner for
the entire queue so that all of the rlimits can count to that owner.
That should entirely remove the need to call get_ucounts and
put_ucounts in sigqueue_alloc and sigqueue_free. It is difficult
because Linux unlike POSIX supports setuid that works on a single
thread"
* 'ucount-fixes-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
ucounts: Move get_ucounts from cred_alloc_blank to key_change_session_keyring
ucounts: Proper error handling in set_cred_ucounts
ucounts: Pair inc_rlimit_ucounts with dec_rlimit_ucoutns in commit_creds
ucounts: Fix signal ucount refcounting
Current release - regressions:
- revert "vrf: reset skb conntrack connection on VRF rcv",
there are valid uses for previous behavior
- can: m_can: fix iomap_read_fifo() and iomap_write_fifo()
Current release - new code bugs:
- mlx5: e-switch, return correct error code on group creation failure
Previous releases - regressions:
- sctp: fix transport encap_port update in sctp_vtag_verify
- stmmac: fix E2E delay mechanism (in PTP timestamping)
Previous releases - always broken:
- netfilter: ip6t_rt: fix out-of-bounds read of ipv6_rt_hdr
- netfilter: xt_IDLETIMER: fix out-of-bound read caused by lack of init
- netfilter: ipvs: make global sysctl read-only in non-init netns
- tcp: md5: fix selection between vrf and non-vrf keys
- ipv6: count rx stats on the orig netdev when forwarding
- bridge: mcast: use multicast_membership_interval for IGMPv3
- can:
- j1939: fix UAF for rx_kref of j1939_priv
abort sessions on receiving bad messages
- isotp: fix TX buffer concurrent access in isotp_sendmsg()
fix return error on FC timeout on TX path
- ice: fix re-init of RDMA Tx queues and crash if RDMA was not inited
- hns3: schedule the polling again when allocation fails,
prevent stalls
- drivers: add missing of_node_put() when aborting
for_each_available_child_of_node()
- ptp: fix possible memory leak and UAF in ptp_clock_register()
- e1000e: fix packet loss in burst mode on Tiger Lake and later
- mlx5e: ipsec: fix more checksum offload issues
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAmFxgHwACgkQMUZtbf5S
IrvFgw//T73aR3B2Xvz5/1rtglfmtcUqFQsyGDXGD5HnfbAbsRcz8vcQ/mTsExl7
+mJY/ZuQefsD7UQDyg3GNhbgf1+pEjHC81ryeNsfET7+JxgYLD3NEYSBYUqIFZUo
gStAStGBG+ClQUaqlkGFyyf6GrqwpmxZKRr6F9fUsufQ14m9tvcT/QPcrXL4q7qX
Fz644yUe/IvKnuJDHJVZsc8UXR9NTPCyCNJT9kVewwPMIMEc/xMOg5QONLZT0TlC
Zk4XJIqlBBEQWrN/QwrGXm82aO+3gQZyD5K9AvpczgcBjOr6FJOmN6zkQrqNNWaC
2wPAfWi7DALPtOZR6lCxoeWfLRfdn1ZOn5x2z5xrtAXCV2FTaMg8in9TzJ57qmcb
/l43QzcNGSj1ytyny8pqgdsX2MSqs0O5VSG4egMtz7TeU/rs7uAx2IVHbPT8CHop
PvhVHeUeu9lGu+FUK8piQbb5aVpbA9qlOj/rXNrHDIxdA9McQgVs+tljNG4X5KtX
L7BR84wNg98HtIINVx6RjYz9lOpG1qBuw5RCiqiAaN1RBY7lYAhMaAE6U3azjgC+
AIz/MacNuAz/oTuutQB6/0WZDDJhy4WEy3TrDLlpQNz6yIrpKFN+ftyF6DuVUSMH
PmtZ4E/DLooQL5KwuoDdYDH1gSMlggBejeGHTFJ+RUMuvRePZQ8=
=Hwqr
-----END PGP SIGNATURE-----
Merge tag 'net-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, and can.
We'll have one more fix for a socket accounting regression, it's still
getting polished. Otherwise things look fine.
Current release - regressions:
- revert "vrf: reset skb conntrack connection on VRF rcv", there are
valid uses for previous behavior
- can: m_can: fix iomap_read_fifo() and iomap_write_fifo()
Current release - new code bugs:
- mlx5: e-switch, return correct error code on group creation failure
Previous releases - regressions:
- sctp: fix transport encap_port update in sctp_vtag_verify
- stmmac: fix E2E delay mechanism (in PTP timestamping)
Previous releases - always broken:
- netfilter: ip6t_rt: fix out-of-bounds read of ipv6_rt_hdr
- netfilter: xt_IDLETIMER: fix out-of-bound read caused by lack of
init
- netfilter: ipvs: make global sysctl read-only in non-init netns
- tcp: md5: fix selection between vrf and non-vrf keys
- ipv6: count rx stats on the orig netdev when forwarding
- bridge: mcast: use multicast_membership_interval for IGMPv3
- can:
- j1939: fix UAF for rx_kref of j1939_priv abort sessions on
receiving bad messages
- isotp: fix TX buffer concurrent access in isotp_sendmsg() fix
return error on FC timeout on TX path
- ice: fix re-init of RDMA Tx queues and crash if RDMA was not inited
- hns3: schedule the polling again when allocation fails, prevent
stalls
- drivers: add missing of_node_put() when aborting
for_each_available_child_of_node()
- ptp: fix possible memory leak and UAF in ptp_clock_register()
- e1000e: fix packet loss in burst mode on Tiger Lake and later
- mlx5e: ipsec: fix more checksum offload issues"
* tag 'net-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (75 commits)
usbnet: sanity check for maxpacket
net: enetc: make sure all traffic classes can send large frames
net: enetc: fix ethtool counter name for PM0_TERR
ptp: free 'vclock_index' in ptp_clock_release()
sfc: Don't use netif_info before net_device setup
sfc: Export fibre-specific supported link modes
net/mlx5e: IPsec: Fix work queue entry ethernet segment checksum flags
net/mlx5e: IPsec: Fix a misuse of the software parser's fields
net/mlx5e: Fix vlan data lost during suspend flow
net/mlx5: E-switch, Return correct error code on group creation failure
net/mlx5: Lag, change multipath and bonding to be mutually exclusive
ice: Add missing E810 device ids
igc: Update I226_K device ID
e1000e: Fix packet loss on Tiger Lake and later
e1000e: Separate TGP board type from SPT
ptp: Fix possible memory leak in ptp_clock_register()
net: stmmac: Fix E2E delay mechanism
nfc: st95hf: Make spi remove() callback return zero
net: hns3: disable sriov before unload hclge layer
net: hns3: fix vf reset workqueue cannot exit
...
Fix a bug exposed by a previous fix, where running guests with certain SMT topologies
could crash the host on Power8.
Fix atomic sleep warnings when re-onlining CPUs, when PREEMPT is enabled.
Thanks to: Nathan Lynch, Srikar Dronamraju, Valentin Schneider.
-----BEGIN PGP SIGNATURE-----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=572c
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.15-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix a bug exposed by a previous fix, where running guests with
certain SMT topologies could crash the host on Power8.
- Fix atomic sleep warnings when re-onlining CPUs, when PREEMPT is
enabled.
Thanks to Nathan Lynch, Srikar Dronamraju, and Valentin Schneider.
* tag 'powerpc-5.15-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/smp: do not decrement idle task preempt count in CPU offline
powerpc/idle: Don't corrupt back chain when going idle
Another change to the API io-wq worker limitation API added in 5.15,
apply the limit to all prior users that already registered a tctx. It
may be confusing as it's now, in particular the change covers the
following 2 cases:
TASK1 | TASK2
_________________________________________________
ring = create() |
| limit_iowq_workers()
*not limited* |
TASK1 | TASK2
_________________________________________________
ring = create() |
| issue_requests()
limit_iowq_workers() |
| *not limited*
A note on locking, it's safe to traverse ->tctx_list as we hold
->uring_lock, but do that after dropping sqd->lock to avoid possible
problems. It's also safe to access tctx->io_wq there because tasks
kill it only after removing themselves from tctx_list, see
io_uring_cancel_generic() -> io_uring_clean_tctx()
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/d6e09ecc3545e4dc56e43c906ee3d71b7ae21bed.1634818641.git.asml.silence@gmail.com
Reviewed-by: Hao Xu <haoxu@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Flush the destination page before invoking RECEIVE_UPDATE_DATA, as the
PSP encrypts the data with the guest's key when writing to guest memory.
If the target memory was not previously encrypted, the cache may contain
dirty, unecrypted data that will persist on non-coherent systems.
Fixes: 15fb7de1a7 ("KVM: SVM: Add KVM_SEV_RECEIVE_UPDATE_DATA command")
Cc: stable@vger.kernel.org
Cc: Peter Gonda <pgonda@google.com>
Cc: Marc Orr <marcorr@google.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Masahiro Kozuka <masa.koz@kozuka.jp>
[sean: converted bug report to changelog]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210914210951.2994260-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When updating mmu->pkru_mask, the value can only be added but it isn't
reset in advance. This will make mmu->pkru_mask keep the stale data.
Fix this issue.
Fixes: 2d344105f5 ("KVM, pkeys: introduce pkru_mask to cache conditions")
Signed-off-by: Chenyi Qiang <chenyi.qiang@intel.com>
Message-Id: <20211021071022.1140-1-chenyi.qiang@intel.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The enetc driver does not implement .ndo_change_mtu, instead it
configures the MAC register field PTC{Traffic Class}MSDUR[MAXSDU]
statically to a large value during probe time.
The driver used to configure only the max SDU for traffic class 0, and
that was fine while the driver could only use traffic class 0. But with
the introduction of mqprio, sending a large frame into any other TC than
0 is broken.
This patch fixes that by replicating per traffic class the static
configuration done in enetc_configure_port_mac().
Fixes: cbe9e83594 ("enetc: Enable TC offloading with mqprio")
Reported-by: Richie Pearn <richard.pearn@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: <Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20211020173340.1089992-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are two counters named "MAC tx frames", one of them is actually
incorrect. The correct name for that counter should be "MAC tx error
frames", which is symmetric to the existing "MAC rx error frames".
Fixes: 16eb4c85c9 ("enetc: Add ethtool statistics")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: <Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20211020165206.1069889-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dave is already listed as x86/mm maintainer, has a profund knowledge
of the x86 architecture in general and a good taste in terms of kernel
programming in general.
Add him as a full x86 maintainer with all rights and duties.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/87zgr3flq7.ffs@tglx
'vclock_index' is accessed from sysfs, it shouled be freed
in release function, so move it from ptp_clock_unregister()
to ptp_clock_release().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pci_info instead to avoid unnamed/uninitialized noise:
[197088.688729] sfc 0000:01:00.0: Solarflare NIC detected
[197088.690333] sfc 0000:01:00.0: Part Number : SFN5122F
[197088.729061] sfc 0000:01:00.0 (unnamed net_device) (uninitialized): no SR-IOV VFs probed
[197088.729071] sfc 0000:01:00.0 (unnamed net_device) (uninitialized): no PTP support
Inspired by fa44821a4d ("sfc: don't use netif_info et al before
net_device is registered") from Heiner Kallweit.
Signed-off-by: Erik Ekman <erik@kryo.se>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 1/10GbaseT modes were set up for cards with SFP+ cages in
3497ed8c85 ("sfc: report supported link speeds on SFP connections").
10GbaseT was likely used since no 10G fibre mode existed.
The missing fibre modes for 1/10G were added to ethtool.h in 5711a98221
("net: ethtool: add support for 1000BaseX and missing 10G link modes")
shortly thereafter.
The user guide available at https://support-nic.xilinx.com/wp/drivers
lists support for the following cable and transceiver types in section 2.9:
- QSFP28 100G Direct Attach Cables
- QSFP28 100G SR Optical Transceivers (with SR4 modules listed)
- SFP28 25G Direct Attach Cables
- SFP28 25G SR Optical Transceivers
- QSFP+ 40G Direct Attach Cables
- QSFP+ 40G Active Optical Cables
- QSFP+ 40G SR4 Optical Transceivers
- QSFP+ to SFP+ Breakout Direct Attach Cables
- QSFP+ to SFP+ Breakout Active Optical Cables
- SFP+ 10G Direct Attach Cables
- SFP+ 10G SR Optical Transceivers
- SFP+ 10G LR Optical Transceivers
- SFP 1000BASE‐T Transceivers
- 1G Optical Transceivers
(From user guide issue 28. Issue 16 which also includes older cards like
SFN5xxx/SFN6xxx has matching lists for 1/10/40G transceiver types.)
Regarding SFP+ 10GBASE‐T transceivers the latest guide says:
"Solarflare adapters do not support 10GBASE‐T transceiver modules."
Tested using SFN5122F-R7 (with 2 SFP+ ports). Supported link modes do not change
depending on module used (tested with 1000BASE-T, 1000BASE-BX10, 10GBASE-LR).
Before:
$ ethtool ext
Settings for ext:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
10000baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Link partner advertised link modes: Not reported
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: No
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: off
Port: FIBRE
PHYAD: 255
Transceiver: internal
Current message level: 0x000020f7 (8439)
drv probe link ifdown ifup rx_err tx_err hw
Link detected: yes
After:
$ ethtool ext
Settings for ext:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
1000baseX/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Link partner advertised link modes: Not reported
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: No
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: off
Port: FIBRE
PHYAD: 255
Transceiver: internal
Supports Wake-on: g
Wake-on: d
Current message level: 0x000020f7 (8439)
drv probe link ifdown ifup rx_err tx_err hw
Link detected: yes
Signed-off-by: Erik Ekman <erik@kryo.se>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter fixes for net:
1) Crash due to missing initialization of timer data in
xt_IDLETIMER, from Juhee Kang.
2) NF_CONNTRACK_SECMARK should be bool in Kconfig, from Vegard Nossum.
3) Skip netdev events on netns removal, from Florian Westphal.
4) Add testcase to show port shadowing via UDP, also from Florian.
5) Remove pr_debug() code in ip6t_rt, this fixes a crash due to
unsafe access to non-linear skbuff, from Xin Long.
6) Make net/ipv4/vs/debug_level read-only from non-init netns,
from Antoine Tenart.
7) Remove bogus invocation to bash in selftests/netfilter/nft_flowtable.sh
also from Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-10-20
This series contains updates to e1000e, igc, and ice drivers.
Sasha fixes an issue with dropped packets on Tiger Lake platforms for
e1000e and corrects a device ID for igc.
Tony adds missing E810 device IDs for ice.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On KMB, ADV bridge must be programmed and powered on prior to
MIPI DSI HW initialization.
v2: changed to atomic_bridge_chain_enable (Sam)
Fixes: 98521f4d4b ("drm/kmb: Mipi DSI part of the display driver")
Co-developed-by: Edmund Dea <edmund.j.dea@intel.com>
Signed-off-by: Edmund Dea <edmund.j.dea@intel.com>
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211019230719.789958-1-anitha.chrisanthus@intel.com
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Due to HW limitations, KMB cannot change height, width, or
pixel format after initial plane configuration.
v2: removed memset disp_cfg as it is already zero.
Fixes: 7f7b96a8a0 ("drm/kmb: Add support for KeemBay Display")
Signed-off-by: Edmund Dea <edmund.j.dea@intel.com>
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211013233632.471892-4-anitha.chrisanthus@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Don't clear the shared DPHY registers common to MIPI Rx and MIPI Tx during
DSI initialization since this was causing MIPI Rx reset. Rest of the
writes are bitwise, so will not affect Mipi Rx side.
Fixes: 98521f4d4b ("drm/kmb: Mipi DSI part of the display driver")
Signed-off-by: Edmund Dea <edmund.j.dea@intel.com>
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211013233632.471892-3-anitha.chrisanthus@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
KMB only supports single resolution(1080p), this commit checks for
1920x1080x60 or 1920x1080x59 in crtc_mode_valid.
Also, modes with vfp < 4 are not supported in KMB display. This change
prunes display modes with vfp < 4.
v2: added vfp check
Fixes: 7f7b96a8a0 ("drm/kmb: Add support for KeemBay Display")
Co-developed-by: Edmund Dea <edmund.j.dea@intel.com>
Signed-off-by: Edmund Dea <edmund.j.dea@intel.com>
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link:https://patchwork.freedesktop.org/patch/msgid/20211013233632.471892-2-anitha.chrisanthus@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Use a different value for system clock offset in the
ppl/llp ratio calculations for clocks higher than 500 Mhz.
Fixes: 98521f4d4b ("drm/kmb: Mipi DSI part of the display driver")
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211013233632.471892-1-anitha.chrisanthus@intel.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
This adjusts sync values according to the datasheet
Fixes: 1c243751c0 ("drm/panel: ilitek-ili9881c: add support for Feixin K101-IM2BYL02 panel")
Co-developed-by: Marius Gripsgard <marius@ubports.com>
Signed-off-by: Dan Johansen <strit@manjaro.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210818214818.298089-1-strit@manjaro.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The mxsfb->crtc.funcs may already be NULL when unloading the driver,
in which case calling mxsfb_irq_disable() via drm_irq_uninstall() from
mxsfb_unload() leads to NULL pointer dereference.
Since all we care about is masking the IRQ and mxsfb->base is still
valid, just use that to clear and mask the IRQ.
Fixes: ae1ed00932 ("drm: mxsfb: Stop using DRM simple display pipeline helper")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Abrecht <public@danielabrecht.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211016210446.171616-1-marex@denx.de
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Syzkaller reports a null pointer dereference in fuse_test_super() that is
caused by sb->s_fs_info being NULL.
This is due to the fact that fuse_fill_super() is initializing s_fs_info,
which is too late, it's already on the fs_supers list. The initialization
needs to be done in sget_fc() with the sb_lock held.
Move allocation of fuse_mount and fuse_conn from fuse_fill_super() into
fuse_get_tree().
After this ->kill_sb() will always be called with non-NULL ->s_fs_info,
hence fuse_mount_destroy() can drop the test for non-NULL "fm".
Reported-by: syzbot+74a15f02ccb51f398601@syzkaller.appspotmail.com
Fixes: 5d5b74aa9c ("fuse: allow sharing existing sb")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
1. call fuse_mount_destroy() for open coded variants
2. before deactivate_locked_super() don't need fuse_mount destruction since
that will now be done (if ->s_fs_info is not cleared)
3. rearrange fuse_mount setup in fuse_get_tree_submount() so that the
regular pattern can be used
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
The ->put_super callback is called from generic_shutdown_super() in case of
a fully initialized sb. This is called from kill_***_super(), which is
called from ->kill_sb instances.
Fuse uses ->put_super to destroy the fs specific fuse_mount and drop the
reference to the fuse_conn, while it does the same on each error case
during sb setup.
This patch moves the destruction from fuse_put_super() to
fuse_mount_destroy(), called at the end of all ->kill_sb instances. A
follup patch will clean up the error paths.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Checking "fm" works because currently sb->s_fs_info is cleared on error
paths; however, sb->s_root is what generic_shutdown_super() checks to
determine whether the sb was fully initialized or not.
This change will allow cleanup of sb setup error paths.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Since commit c300ab9f08 ("KVM: x86: Replace late check_nested_events() hack with
more precise fix") there is no longer the certainty that check_nested_events()
tries to inject an external interrupt vmexit to L1 on every call to vcpu_enter_guest.
Therefore, even in that case we need to set KVM_REQ_EVENT. This ensures
that inject_pending_event() is called, and from there kvm_check_nested_events().
Fixes: c300ab9f08 ("KVM: x86: Replace late check_nested_events() hack with more precise fix")
Cc: stable@vger.kernel.org
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The kvm_x86_sync_pir_to_irr callback can sometimes set KVM_REQ_EVENT.
If that happens exactly at the time that an exit is handled as
EXIT_FASTPATH_REENTER_GUEST, vcpu_enter_guest will go incorrectly
through the loop that calls kvm_x86_run, instead of processing
the request promptly.
Fixes: 379a3c8ee4 ("KVM: VMX: Optimize posted-interrupt delivery for timer fastpath")
Cc: stable@vger.kernel.org
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There's a mistake in commit 2be7828c9f ("get rid of autofs_getpath()")
that affects kernels from v5.13.0, basically missed because of me not
fully testing the change for Al.
The problem is that the hash calculation for the wait name qstr hasn't
been updated to account for the change to use dentry_path_raw(). This
prevents the correct matching an existing wait resulting in multiple
notifications being sent to the daemon for the same mount which must
not occur.
The problem wasn't discovered earlier because it only occurs when
multiple processes trigger a request for the same mount concurrently
so it only shows up in more aggressive testing.
Fixes: 2be7828c9f ("get rid of autofs_getpath()")
Cc: stable@vger.kernel.org
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
superblocks issue was particularly annoying because for unexperienced
users it essentially exacted a reboot to establish a new functional
mount in that scenario.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAmFwWuYTHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHziwdHB/wJEvFkMQrlzbgVmijhmneU+TseAMxR
UBGnsyHdiimIDWqzb81cBuDfrocQzyhntghP2lBzcbzI+gZN1KlrYzKAbYk++cfi
E5Zbw3U8+moa5B2CnO19QEgmJY5DoXYXb6AbO3udIIj1Ls9lx0ByUyDoSn6fZyVH
iUQ9OH7zVTsTscoaBiEVcutmhQjIFjoYJqPpfCg6/15xcXX/L1DvxQFBWOxXqHQw
LYfCQIu8orrA2QdZpuTRpklrMg1Ih+RmqYTdQST6tTtTKJUrHPI0r3A8c2vUoBk1
ph4fBNsAMUqFn1fIGT88PJg81RC5RC3E6D5PqErzRFsPbAv9FHfGYvGQ
=FadF
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-5.15-rc7' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"Two important filesystem fixes, marked for stable.
The blocklisted superblocks issue was particularly annoying because
for unexperienced users it essentially exacted a reboot to establish a
new functional mount in that scenario"
* tag 'ceph-for-5.15-rc7' of git://github.com/ceph/ceph-client:
ceph: fix handling of "meta" errors
ceph: skip existing superblocks that are blocklisted or shut down when mounting
Current Work Queue Entry (WQE) checksum (csum) flags in the ethernet
segment (eseg) in case of IPsec crypto offload datapath are not aligned
with PRM/HW expectations.
Currently the driver always sets the l3_inner_csum flag in case of IPsec
because of the wrong usage of skb->encapsulation as indicator for inner
IPsec header since skb->encapsulation is always ON for IPsec packets
since IPsec itself is an encapsulation protocol. The above forced a
failing attempts of calculating csum of non-existing segments (like in
the IP|ESP|TCP packet case which does not have an l3_inner) which led
to lots of packet drops hence the low throughput.
Fix by using xo->inner_ipproto as indicator for inner IPsec header
instead of skb->encapsulation in addition to setting the csum flags
as following:
* Tunnel Mode:
* Pkt: MAC IP ESP IP L4
* CSUM: l3_cs | l3_inner_cs | l4_inner_cs
*
* Transport Mode:
* Pkt: MAC IP ESP L4
* CSUM: l3_cs [ | l4_cs (checksum partial case)]
*
* Tunnel(VXLAN TCP/UDP) over Transport Mode
* Pkt: MAC IP ESP UDP VXLAN IP L4
* CSUM: l3_cs | l3_inner_cs | l4_inner_cs
Fixes: f1267798c9 ("net/mlx5: Fix checksum issue of VXLAN and IPsec crypto offload")
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
IPsec crypto offload current Software Parser (SWP) fields settings in
the ethernet segment (eseg) are not aligned with PRM/HW expectations.
Among others in case of IP|ESP|TCP packet, current driver sets the
offsets for inner_l3 and inner_l4 although there is no inner l3/l4
headers relative to ESP header in such packets.
SWP provides the offsets for HW ,so it can be used to find csum fields
to offload the checksum, however these are not necessarily used by HW
and are used as fallback in case HW fails to parse the packet, e.g
when performing IPSec Transport Aware (IP | ESP | TCP) there is no
need to add SW parse on inner packet. So in some cases packets csum
was calculated correctly , whereas in other cases it failed. The later
faced csum errors (caused by wrong packet length calculations) which
led to lots of packet drops hence the low throughput.
Fix by setting the SWP fields as expected in a IP|ESP|TCP packet.
the following describe the expected SWP offsets:
* Tunnel Mode:
* SWP: OutL3 InL3 InL4
* Pkt: MAC IP ESP IP L4
*
* Transport Mode:
* SWP: OutL3 OutL4
* Pkt: MAC IP ESP L4
*
* Tunnel(VXLAN TCP/UDP) over Transport Mode
* SWP: OutL3 InL3 InL4
* Pkt: MAC IP ESP UDP VXLAN IP L4
Fixes: f1267798c9 ("net/mlx5: Fix checksum issue of VXLAN and IPsec crypto offload")
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
During suspend flow the driver calls mlx5e_destroy_vlan_table() which
does not only delete the vlans steering flow rules, but also frees the
data on currently active vlans, thus it is not restored during resume
flow.
This fix keeps the vlan data on suspend flow and frees it only on driver
remove flow.
Fixes: 6783f0a21a ("net/mlx5e: Dynamic alloc vlan table for netdev when needed")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Dan Carpenter report:
The patch f47e04eb96: "net/mlx5: E-switch, Allow setting share/max
tx rate limits of rate groups" from May 31, 2021, leads to the
following Smatch static checker warning:
drivers/net/ethernet/mellanox/mlx5/core/esw/qos.c:483 esw_qos_create_rate_group()
warn: passing zero to 'ERR_PTR'
If min rate normalization failed then error code may be overwritten to 0
if scheduling element destruction succeed. Ignore this value and always
return initial one.
Fixes: f47e04eb96 ("net/mlx5: E-switch, Allow setting share/max tx rate limits of rate groups")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Both multipath and bonding events are changing the HW LAG state
independently.
Handling one of the features events while the other is already
enabled can cause unwanted behavior, for example handling
bonding event while multipath enabled will disable the lag and
cause multipath to stop working.
Fix it by ignoring bonding event while in multipath and ignoring FIB
events while in bonding mode.
Fixes: 544fe7c2e6 ("net/mlx5e: Activate HW multipath and handle port affinity based on FIB events")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Again it became bigger than wished, unfortunately, as this contains
quite a few ASoC fixes that came up a bit late. It also includes
yet more HD- and USB-audio quirks: I decided to merge them now, as
those are for stable, and we'll need them sooner or later.
Although the volumes are a bit high, all changes are device-specific
(and reasonably small) fixes, so it should be safe for the late rc.
-----BEGIN PGP SIGNATURE-----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=zrEF
-----END PGP SIGNATURE-----
Merge tag 'sound-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Again it became bigger than wished, unfortunately, as this contains
quite a few ASoC fixes that came up a bit late. It also includes yet
more HD- and USB-audio quirks: I decided to merge them now, as those
are for stable, and we'll need them sooner or later.
Although the volumes are a bit high, all changes are device-specific
(and reasonably small) fixes, so it should be safe for the late rc"
* tag 'sound-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Fix microphone sound on Jieli webcam.
ALSA: hda/realtek: Fixes HP Spectre x360 15-eb1xxx speakers
ALSA: usb-audio: Provide quirk for Sennheiser GSP670 Headset
ALSA: hda/realtek: Add quirk for Clevo PC50HS
ALSA: usb-audio: add Schiit Hel device to quirk table
ASoC: wm8960: Fix clock configuration on slave mode
ASoC: cs42l42: Ensure 0dB full scale volume is used for headsets
ASoC: soc-core: fix null-ptr-deref in snd_soc_del_component_unlocked()
ASoC: codec: wcd938x: Add irq config support
ASoC: DAPM: Fix missing kctl change notifications
ASoC: Intel: bytcht_es8316: Utilize dev_err_probe() to avoid log saturation
ASoC: Intel: bytcht_es8316: Switch to use gpiod_get_optional()
ASoC: Intel: bytcht_es8316: Use temporary variable for struct device
ASoC: Intel: bytcht_es8316: Get platform data via dev_get_platdata()
ASoC: wcd938x: Fix jack detection issue
ASoC: nau8824: Fix headphone vs headset, button-press detection no longer working
ASoC: cs4341: Add SPI device ID table
ASoC: pcm179x: Add missing entries SPI to device ID table
ASoC: fsl_xcvr: Fix channel swap issue with ARC
ASoC: pcm512x: Mend accesses to the I2S_1 and I2S_2 registers
-----BEGIN PGP SIGNATURE-----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=tBGu
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20211019' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit fix from Paul Moore:
"One small audit patch to add a pointer NULL check"
* tag 'audit-pr-20211019' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: fix possible null-pointer dereference in audit_filter_rules
As part of support for E810 XXV devices, some device ids were
inadvertently left out. Add those missing ids.
Fixes: 195fb97766 ("ice: add additional E810 device id")
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
The device ID for I226_K was incorrectly assigned, update the device
ID to the correct one.
Fixes: bfa5e98c9d ("igc: Add new device ID")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Update the HW MAC initialization flow. Do not gate DMA clock from
the modPHY block. Keeping this clock will prevent dropped packets
sent in burst mode on the Kumeran interface.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=213651
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=213377
Fixes: fb776f5d57 ("e1000e: Add support for Tiger Lake")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Mark Pearson <markpearson@lenovo.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
- While cleaning up some of the tracing recursion protection logic,
I discovered a scenario that the current design would miss, and
would allow an infinite recursion. Removing an optimization trick
that opened the hole, fixes the issue and cleans up the code as well.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCYW7CqRQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qmVWAQDnboKAUVmB/3D/L1T9XdWEq4AzCS6W
51QpzWff0pBVkwEAuc1af2gqDZ6/N9sQjN9kGxikY6luVs3CSQ1yHkcanQw=
=1zGP
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Recursion fix for tracing.
While cleaning up some of the tracing recursion protection logic, I
discovered a scenario that the current design would miss, and would
allow an infinite recursion. Removing an optimization trick that
opened the hole fixes the issue and cleans up the code as well"
* tag 'trace-v5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Have all levels of checks prevent recursion
- Renamed CTL_STATUS to CTL_FSTATUS to fix a redefined warning
-----BEGIN PGP SIGNATURE-----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=D96y
-----END PGP SIGNATURE-----
Merge tag 'nios2_fixes_for_v5.15_part2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux
Pull nios2 fix from Dinh Nguyen:
- Renamed CTL_STATUS to CTL_FSTATUS to fix a redefined warning
* tag 'nios2_fixes_for_v5.15_part2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
NIOS2: irqflags: rename a redefined register name
