Bluetooth HCI devices indicate if they are able to wakeup in the wakeup
callback since 'commit 4539ca67fe ("Bluetooth: Rename driver
.prevent_wake to .wakeup")'. This patch adds a default wakeup callback
for Bluetooth HCI UAR devices. It assumes Bluetooth HCI UART devices are
wakeable for backward compatibility. For those who need a customized
behavior, one can override it before calling hci_uart_register_device().
Fixes: 4539ca67fe ("Bluetooth: Rename driver .prevent_wake to .wakeup")
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Commit ce64b3e949 ("Bluetooth: mt7921s: Support wake on bluetooth")
adds the wake on bluethooth via a dedicated GPIO.
Extend the wake-on-bluetooth to use the SDIO DAT1 pin (in-band wakeup),
when supported by the SDIO host driver.
Co-developed-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The BCM4349B1, aka CYW/BCM89359, is a WiFi+BT chip and its Bluetooth
portion can be controlled over serial.
Two subversions are added for the chip, because ROM firmware reports
002.002.013 (at least for the chips I have here), while depending on
patchram firmware revision, either 002.002.013 or 002.002.014 is
reported.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As platform_driver_register() could fail, it should be better
to deal with the return value in order to maintain the code
consisitency.
Fixes: 1ab1f239bf ("Bluetooth: hci_intel: Add support for platform driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use the presence of a DT property, "brcm,requires-autobaud-mode", to enable
startup in autobaud mode. If the property is present, the device is started
in autobaud mode by asserting RTS (BT_UART_CTS_N) prior to powering on the
device.
Also prevent the use of unsupported commands for devices started in
autobaud mode. Only a limited subset of HCI commands are supported in
autobaud mode.
Some devices (e.g. CYW5557x) require autobaud mode to enable FW loading.
Autobaud mode can also be required on some boards where the controller
device is using a non-standard baud rate in normal mode when first powered
on.
Signed-off-by: Hakan Jansson <hakan.jansson@infineon.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This fixes the return value of qca_wakeup(), since
.wakeup work inversely with original .prevent_wake.
Fixes: 4539ca67fe (Bluetooth: Rename driver .prevent_wake to .wakeup)
Signed-off-by: Sai Teja Aluvala <quic_saluvala@quicinc.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sending WMT command during the reset in progress is invalid and would get
no response from firmware until the reset is complete, so we ignore the WMT
command here to resolve the issue which causes the whole reset process
taking too long.
Fixes: 8fafe70225 ("Bluetooth: mt7921s: support bluetooth reset mechanism")
Co-developed-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to FW advised sequence, mt7921s need to re-acquire privilege
immediately after the firmware download is complete before normal running.
Otherwise, it is still possible the bus may be stuck in an abnormal status
that causes FW initialization failure in the current driver.
Fixes: 752aea5848 ("Bluetooth: mt7921s: fix bus hang with wrong privilege")
Co-developed-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the device ID for the BCM4373A0 module, found e.g. in
the Infineon (Cypress) CYW4373E chip. The required firmware file is
named 'BCM4373A0.hcd'.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add the support for RTL8852C BT controller on USB interface.
The necessary firmware file will be submitted to linux-firmware.
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This sets HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN for QCA controllers
since SCO appear to not work when using HCI_OP_ENHANCED_SETUP_SYNC_CONN.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215576
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
While looking at a crash report on a timer list being corrupted, which
usually happens when a timer is freed while still active. This is
commonly triggered by code calling del_timer() instead of
del_timer_sync() just before freeing.
One possible culprit is the hci_qca driver, which does exactly that.
Eric mentioned that wake_retrans_timer could be rearmed via the work
queue, so also move the destruction of the work queue before
del_timer_sync().
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: stable@vger.kernel.org
Fixes: 0ff252c197 ("Bluetooth: hciuart: Add support QCA chipset for UART")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The only usage of regmap_ibt is to (after the regmap_init() macro is
expanded), pass its address to __regmap_init(), which takes a pointer to
const struct regmap_bus as input. Make it const to allow the compiler to
put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix the incorrect pointer check on ven_data.
Fixes: f41b91fa17 ("Bluetooth: mt7921s: Add .btmtk_get_codec_config_data")
Co-developed-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are provedly different firmware variants for the different
phones using some of these chips. These were extracted from a few
Samsung phones:
37446 BCM4334B0.samsung,codina-tmo.hcd
37366 BCM4334B0.samsung,golden.hcd
37403 BCM4334B0.samsung,kyle.hcd
37366 BCM4334B0.samsung,skomer.hcd
This patch supports the above naming schedule with inserting
[.board_name] between the firmware name and ".hcd". This scheme
is the same as used by the companion BRCM wireless chips
as can be seen in
drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c
or just by looking at the firmwares in linux-firmware/brcm.
Currently we only support board variants using the device
tree compatible string as board type, but other schemes are
possible.
This makes it possible to successfully load a few unique
firmware variants for some Samsung phones.
Cc: phone-devel@vger.kernel.org
Cc: Markuss Broks <markuss.broks@gmail.com>
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
ath3k.c hasn't use any macro or function declared in linux/device.h.
Thus, these files can be removed from ath3k.c safely without
affecting the compilation of the ./drivers/bluetooth module
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
bcm203x.c hasn't use any macro or function declared in linux/atomic.h.
Thus, these files can be removed from bcm203x.c safely without
affecting the compilation of the ./drivers/bluetooth module
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The DSDT for the Asus TF103C specifies a IOAPIC IRQ for the HCI -> host IRQ
but this is not correct. Unlike the previous entries in the table, this
time the correct GPIO to use instead is known; and the TF103C is battery
powered making runtime-pm support more important.
Extend the bcm_broken_irq_dmi_table mechanism to allow specifying the right
GPIO instead of just always disabling runtime-pm and add an entry to it for
the Asus TF103C.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
It is time to add wide band speech (WBS) support.
Reviewed-by: Mark Chen <markyawenchen@gmail.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
add .btmtk_get_codec_config_data to get codec configuration data.
In HFP offload usecase, controllers need to be set codec details before
opening SCO. This callback function is used to fetch vendor specific codec
config data.
This is a preliminary patch to add the WBS support to the MT7921 driver.
Reviewed-by: Mark Chen <markyawenchen@gmail.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add .get_data_path_id to fetch data_path_id for MT7921 to support HFP
offload use case.
This is a preliminary patch to add the WBS support to the MT7921 driver.
Reviewed-by: Mark Chen <markyawenchen@gmail.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The patch set HCI_QUIRK_VALID_LE_STATES to be consistent with the btusb for
MT7921 and is required for the likes of experimental LE simultaneous roles.
Reviewed-by: Mark Chen <markyawenchen@gmail.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix the following kernel oops in btmtksdio_interrrupt
[ 14.339134] btmtksdio_interrupt+0x28/0x54
[ 14.339139] process_sdio_pending_irqs+0x68/0x1a0
[ 14.339144] sdio_irq_work+0x40/0x70
[ 14.339154] process_one_work+0x184/0x39c
[ 14.339160] worker_thread+0x228/0x3e8
[ 14.339168] kthread+0x148/0x3ac
[ 14.339176] ret_from_fork+0x10/0x30
That happened because hdev->power_on is already called before
sdio_set_drvdata which btmtksdio_interrupt handler relies on is not
properly set up.
The details are shown as the below: hci_register_dev would run
queue_work(hdev->req_workqueue, &hdev->power_on) as WQ_HIGHPRI
workqueue_struct to complete the power-on sequeunce and thus hci_power_on
may run before sdio_set_drvdata is done in btmtksdio_probe.
The hci_dev_do_open in hci_power_on would initialize the device and enable
the interrupt and thus it is possible that btmtksdio_interrupt is being
called right before sdio_set_drvdata is filled out.
When btmtksdio_interrupt is being called and sdio_set_drvdata is not filled
, the kernel oops is going to happen because btmtksdio_interrupt access an
uninitialized pointer.
Fixes: 9aebfd4a22 ("Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices")
Reviewed-by: Mark Chen <markyawenchen@gmail.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This code has an uninitialized variable warning:
drivers/bluetooth/btmtkuart.c:184 mtk_hci_wmt_sync()
error: uninitialized symbol 'wc'.
But it also has error paths which have memory leaks.
Fixes: 8f550f55b155 ("Bluetooth: btmtkuart: rely on BT_MTK module")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add the support for RTL8852B BT controller on USB interface.
The necessary firmware file will be submitted to linux-firmware.
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Syzbot hit general protection fault in __pm_runtime_resume(). The problem
was in missing NULL check.
hu->serdev can be NULL and we should not blindly pass &serdev->dev
somewhere, since it will cause GPF.
Reported-by: syzbot+b9bd12fbed3485a3e51f@syzkaller.appspotmail.com
Fixes: d9dd833cf6 ("Bluetooth: hci_h5: Add runtime suspend")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Another subset of the more recent batch of Chinese clones aren't
specs-compliant and seem to lock up whenever they receive a
HCI_OP_SET_EVENT_FLT with flt_type set to zero/HCI_FLT_CLEAR_ALL,
which on Linux (until the recent HCI state-machine refactor) happened
right at BR/EDR setup. As there are other less-straightforward ways
of reaching those operations, this patch is still relevant.
So, while all the previous efforts to wrangle the herd of fake CSRs
seem to be paying off (and these also get detected as such) we
still need to take care of this quirk; testers seem to agree
that these dongles tend to work well enough afterwards.
From some cursory USB packet capture on Windows it seems like
that driver doesn't appear to use this clear-all functionality at all.
This patch was tested on some really popular AliExpress-style
dongles, in my case marked as "V5.0". Chip markings: UG8413,
the backside of the PCB says "USB Dangel" (sic).
Here is the `hciconfig -a` output; for completeness:
hci0: Type: Primary Bus: USB
BD Address: 00:1A:7D:DA:7X:XX ACL MTU: 679:8 SCO MTU: 48:16
UP RUNNING PSCAN ISCAN
Features: 0xbf 0x3e 0x4d 0xfa 0xdb 0x3d 0x7b 0xc7
Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3
Link policy: RSWITCH SNIFF
Link mode: PERIPHERAL ACCEPT
Name: 'CSR8510 A10.'
Class: 0x7c0104
Service Classes: Rendering, Capturing, Object Transfer, Audio, Telephony
Device Class: Computer, Desktop workstation
HCI Version: 4.0 (0x6) Revision: 0x3120
LMP Version: 4.0 (0x6) Subversion: 0x22bb
Manufacturer: Cambridge Silicon Radio (10)
As well as the `lsusb -vv -d 0a12:0001`:
ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode)
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 224 Wireless
bDeviceSubClass 1 Radio Frequency
bDeviceProtocol 1 Bluetooth
bMaxPacketSize0 64
idVendor 0x0a12 Cambridge Silicon Radio, Ltd
idProduct 0x0001 Bluetooth Dongle (HCI mode)
bcdDevice 88.91
iManufacturer 0
iProduct 2 BT DONGLE10
iSerial 0
bNumConfigurations 1
Also, changed the benign dmesg print that shows up whenever the
generic force-suspend fails from bt_dev_err to bt_dev_warn;
it's okay and done on a best-effort basis, not a problem
if that does not work.
Also, swapped the HCI subver and LMP subver numbers for the Barrot
in the comment, which I copied wrong the last time around.
Fixes: 81cac64ba2 ("Bluetooth: Deal with USB devices that are faking CSR vendor")
Fixes: cde1a8a992 ("Bluetooth: btusb: Fix and detect most of the Chinese Bluetooth controllers")
Fixes: d74e0ae7e0 ("Bluetooth: btusb: Fix detection of some fake CSR controllers with a bcdDevice val of 0x0134")
Fixes: 0671c06623 ("Bluetooth: btusb: Add workaround for remote-wakeup issues with Barrot 8041a02 fake CSR controllers")
Fixes: f4292e2faf ("Bluetooth: btusb: Make the CSR clone chip force-suspend workaround more generic")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=60824
Link: https://gist.github.com/nevack/6b36b82d715dc025163d9e9124840a07
Cc: stable@vger.kernel.org
Cc: Hans de Goede <hdegoede@redhat.com>
Tested-by: Gonzalo Tornaría <tornaria@cmat.edu.uy>
Tested-by: Mateus Lemos <lemonsmateus@gmail.com>
Tested-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is a conflict between MediaTek wmt event and msft vendor extension
logic in the core layer since 145373cb1b ("Bluetooth: Add framework for
Microsoft vendor extension") was introduced because we changed the type of
mediatek wmt event to the type of msft vendor event in the driver.
But the purpose we reported mediatek event to the core layer is for the
diagnostic purpose with that we are able to see the full packet trace via
monitoring socket with btmon. Thus, it is harmless we keep the original
type of mediatek vendor event here to avoid breaking the msft extension
function especially they can be supported by Mediatek future devices.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add the compatible for BCM43430A0 bluetooth used in lg-lenok and
BCM43430A1 used in asus-sparrow.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This makes use of BIT macro when declaring BTUSB flags which makes it
understand how many bits are in use and many are left.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is a conflict between MediaTek wmt event and msft vendor extension
logic in the core layer since 145373cb1b ("Bluetooth: Add framework for
Microsoft vendor extension") was introduced because we changed the type of
mediatek wmt event to the type of msft vendor event in the driver.
But the purpose we reported mediatek event to the core layer is for the
diagnostic purpose with that we are able to see the full packet trace via
monitoring socket with btmon. Thus, it is harmless we keep the original
type of mediatek vendor event here to avoid breaking the msft extension
function especially they can be supported by Mediatek chipset like MT7921
, MT7922 devices and future devices.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Implement .cmd_timeout to reset the MT7921s device via a dedicated GPIO
pin when the firmware hang or the command has no response.
Co-developed-by: Mark Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Chih-Ying Chiang <chih-yin.chiang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
WCN6855 2.1 will reset to apply firmware downloaded, so wait
a moment for reset done then go ahead to improve stability.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
- Add support for RTL8822C hci_ver 0x08
- Add support for RTL8852AE part 0bda:2852
- Fix WBS setting for Intel legacy ROM products
- Enable SCO over I2S ib mt7921s
- Increment management interface revision
-----BEGIN PGP SIGNATURE-----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=/KS7
-----END PGP SIGNATURE-----
Merge tag 'for-net-next-2022-01-28' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Add support for RTL8822C hci_ver 0x08
- Add support for RTL8852AE part 0bda:2852
- Fix WBS setting for Intel legacy ROM products
- Enable SCO over I2S ib mt7921s
- Increment management interface revision
* tag 'for-net-next-2022-01-28' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next: (30 commits)
Bluetooth: Increment management interface revision
Bluetooth: hci_sync: Fix queuing commands when HCI_UNREGISTER is set
Bluetooth: hci_h5: Add power reset via gpio in h5_btrtl_open
Bluetooth: btrtl: Add support for RTL8822C hci_ver 0x08
Bluetooth: hci_event: Fix HCI_EV_VENDOR max_len
Bluetooth: hci_core: Rate limit the logging of invalid SCO handle
Bluetooth: hci_event: Ignore multiple conn complete events
Bluetooth: msft: fix null pointer deref on msft_monitor_device_evt
Bluetooth: btmtksdio: mask out interrupt status
Bluetooth: btmtksdio: run sleep mode by default
Bluetooth: btmtksdio: lower log level in btmtksdio_runtime_[resume|suspend]()
Bluetooth: mt7921s: fix btmtksdio_[drv|fw]_pmctrl()
Bluetooth: mt7921s: fix bus hang with wrong privilege
Bluetooth: btmtksdio: refactor btmtksdio_runtime_[suspend|resume]()
Bluetooth: mt7921s: fix firmware coredump retrieve
Bluetooth: hci_serdev: call init_rwsem() before p->open()
Bluetooth: Remove kernel-doc style comment block
Bluetooth: btusb: Whitespace fixes for btusb_setup_csr()
Bluetooth: btusb: Add one more Bluetooth part for the Realtek RTL8852AE
Bluetooth: btintel: Fix WBS setting for Intel legacy ROM products
...
====================
Link: https://lore.kernel.org/r/20220128205915.3995760-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add power reset for bluetooth via enable-gpios in h5_btrtl_open function.
While testing the RTL8822CS SDIO WiFi/BT adapter, it was found that in
some cases the kernel could not initialize BT firmware. However,
manually resetting the adapter via gpio (off/on sequence) allows it to
start correctly.
Apparently, when the system starts, the adapter is in an undefined state
(including unknown gpio state after starting uboot). A forced reset helps
to initialize the adapter in most cases. It has been found experimentally
that 100 ms is sufficient for a reset.
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
