The Synopsys DesignWare DWAPB GPIO block is popular to
synthesize amongst many architectures: X86, ARM, ARC.
The driver was restricted to only these archs due to
using [read|write]l_relaxed() accessors that were not
universally available in the past,
but as of commit 9439eb3ab9
"asm-generic: io: implement relaxed accessor macros as
conditional wrappers" these accessors are available on all
archs so this should not be a problem any more. Enable the
driver for all archs.
Cc: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Synopsys SDP platform uses DW GPIO controller in design with
ARC cores. So adding ARC to architectures that may select this
GPIO controller.
Even though support for Synopsys SDP is yet to be submitted we'll need
this tiny option enabled at least for properly working interrupts (DW
GPIO controller is used as interrupt controller).
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit 3de07e5aaf290a0b58919 ("drivers: gpio: use devm_kzalloc")
introduce devm_kzalloc() for allocating the memory. In this case kfree
is not required to use. Above commit id introduced the bug that kfree
is not removed from the remove function.
This patch fix the above bug.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Level IRQ handlers and edge IRQ handler are managed by tow different
sets of registers. But currently the driver uses the same mask for the
both registers. It lead to issues with the following scenario:
First, an IRQ is requested on a GPIO to be triggered on front. After,
this an other IRQ is requested for a GPIO of the same bank but
triggered on level. Then the first one will be also setup to be
triggered on level. It leads to an interrupt storm.
The different kind of handler are already associated with two
different irq chip type. With this patch the driver uses a private
mask for each one which solves this issue.
It has been tested on an Armada XP based board and on an Armada 375
board. For the both boards, with this patch is applied, there is no
such interrupt storm when running the previous scenario.
This bug was already fixed but in a different way in the legacy
version of this driver by Evgeniy Dushistov:
9ece8839b1 "ARM: orion: Fix for certain
sequence of request_irq can cause irq storm". The fact the new version
of the gpio drive could be affected had been discussed there:
http://thread.gmane.org/gmane.linux.ports.arm.kernel/344670/focus=364012
Reported-by: Evgeniy A. Dushistov <dushistov@mail.ru>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.7 +
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Create Kconfig submenus for memory mapped, I2C, MFD,
PCI, SPI and USB GPIO drivers to help navigate the forest
of drivers in this subsystem. The I2C, SPI and USB menus
get dependencies so we don't have to see them unless we
have the required subsystem enabled in the first place.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Get rid of AC97, MODULbus and other weird subheadings for
GPIO drivers. Move all MFD drivers out of I2C etc and in under
the MFD comment. This is too weird as it is and makes no
sense, if the dependent parent driver is MFD, group these as
MFD GPIO drivers. Alphabetize and move this comment group
inbetween "I2C" and "PCI" to also have the groups in
alphabetic order.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the Kconfig option for the Broadcom BCM Kona up to the
commin GPIO controllers, as it is currently grouped under
MODULbus expanders which it definately is not.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rearrange the SPI GPIO expanders in alphabetic order
as already indicated by the comment in the file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rearrange PCI GPIO controllers in alphabetic order
as already indicated by the comment in the file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rearrange the I2C GPIO expanders in alphabetic order
as already indicated by the comment in the file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This rearranges the GPIO drivers Kconfig symbols alphabetically
as the top comment in the file already states they should be.
No functional changes whatsoever.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow the kernel to query the driver for a GPIO's pin direction.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver no need to set the owner field, it will be populated
by driver core.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We can use devres API for allocating memory. No need of using kfree.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Header moved from linux/pci_ids.h to uapi/linux/pci_ids.h,
use the new header directly so we can drop
the wrapper in include/linux/pci_ids.h.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
devm_ioremap_resource() returns IOMEM_ERR_PTR() and it never
returns NULL, fix the check to prevent access to invalid
virtual address.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver is orphaned now that mach-msm has been removed.
Delete it.
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Even if bus is not hot-pluggable, the devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now GPIO syscon driver produces bunch of warnings during the
boot of Kesytone 2 SoCs:
gpio-syscon soc:keystone_dsp_gpio@02620240: can't read the dir register offset!
gpio-syscon soc:keystone_dsp_gpio@2620244: can't read the dir register offset!
This message unintentionally was added using dev_err(), but its
actual log level is debug, because third cell of "ti,syscon-dev" is
optional.
Hence change it to dev_dbg() as it should be.
This patch fixes commit:
5a3e3f8 ("gpio: syscon: retriave syscon node and regs offsets from dt")
Reported-by: Russell King <linux@arm.linux.org.uk>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert GPIO IRQ functions to use GPIO offset instead of system
GPIO numbers. This allows to drop unneeded conversations between
system GPIO <-> GPIO offset which are done in many places and
many times.
It is safe to do now because:
- gpiolib always passes GPIO offset to GPIO controller
- OMAP GPIO driver converted to use IRQ domain, so
struct irq_data->hwirq contains GPIO offset
This is preparation step before removing:
#define GPIO_INDEX(bank, gpio)
#define GPIO_BIT(bank, gpio)
int omap_irq_to_gpio()
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 'gpio' parameter isn't needed any more as it
duplicates 'offset' parameter, so drop it.
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert debounce functions to use GPIO offset instead of system
GPIO numbers. This allows to drop unneeded conversations between
system GPIO <-> GPIO offset which are done in many places and
many times.
It is safe to do now because:
- gpiolib always passes GPIO offset to GPIO controller
- OMAP GPIO driver converted to use IRQ domain
This is preparation step before removing:
#define GPIO_INDEX(bank, gpio)
#define GPIO_BIT(bank, gpio)
int omap_irq_to_gpio()
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Both functions omap_set_gpio_dataout_reg() and
omap_set_gpio_dataout_mask() accept GPIO offset
as 'gpio' input parameter, so rename it to 'offset' and
drop usage of GPIO_BIT() macro.
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert omap_gpio_is_input() to use GPIO offset instead of mask and,
in such way, make code simpler and remove few lines of code.
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All systems using the TC3589x multifunction expander uses
devicetree, so don't clutter the place with a lot of
and assume it is there.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When the GPIO module is needed for wake-up, it's module clock must not
be disabled. Hence implement irq_chip.irq_set_wake(), which
increments/decrements the clock's enable_count when needed, and forwards
the wake-up state to the upstream interrupt controller.
This fixes wake-up from s2ram using gpio-keys when using a PM Domain to
manage the module clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The existing variable gpio_chip already points to the gpiochip instance,
hence use it everywhere.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Intel Quark SoC contains the DW GPIO on board. While fixing the build error
the commit 1972c97db5 (gpio: dwapb: fix compile errors) disables the
possibility to build the driver on X86, i.e. Intel Quark.
The patch reenables it for Intel Quark as well.
Since we have Intel Quark SoC introduced in 4.0-rc1 I would like to make this
fix available there as well, though the actual MFD driver [1] is applied only
for next version.
[1] https://lkml.org/lkml/2015/2/1/217
Fixes: 1972c97db5 (gpio: dwapb: fix compile errors)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In acpi_gpiochip_request_interrupts() the handle local
variable already contains the value that we want to pass
to acpi_walk_resources(), so it is better to use that
variable instead of evaluating ACPI_HANDLE() once more
for the same device.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If dev is NULL in __gpiod_get_index() and both ACPI and OF are
enabled, it will be checked twice before the code decides to give
up with DT/ACPI lookup, so avoid that.
Also use the observation that ACPI_COMPANION() is much more efficient
than ACPI_HANDLE(), because the latter uses the former and carries out
a check and a pointer dereference on top of it, so replace the
ACPI_HANDLE() check with an ACPI_COMPANION() one which does not
require the additional IS_ENABLED(CONFIG_ACPI) check too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If GPIO driver use pin mapping, need to translate pin number
between ACPI table and GPIO driver.
This issue is found on one platform with Cherryview gpio
controller, kernel is hang when executed _PS0 method of
one ACPI device, since without this translation, it access
invalid gpiodesc array.
Verified it works again with this patch.
Signed-off-by: qipeng.zha <qipeng.zha@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the GPIOs found on the Fintek SuperI/O chip F71869A,
such as the one found on the Jetway JNF99-525 motherboard, to the f7188x
gpio driver.
Signed-off-by: Andreas Bofjall <andreas@gazonk.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the GPIOs found on the Fintek SuperI/O chip F71869, such
as the one found on the Jetway NF96u-525 motherboard, to the f7188x gpio
driver.
Signed-off-by: Andreas Bofjall <andreas@gazonk.org>
Tested-by: Les Schaffer <schaffer@optonline.net>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The company is called "Fintek", not "Fintech". Fix it.
Signed-off-by: Andreas Bofjall <andreas@gazonk.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 1feb57a245
"gpio: add parameter to allow the use named gpios"
includes a double-consted array. What we want is not
const const * but const * const (const pointer to const
data). Fix this.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Olliver Schinagl <oliver@schinagl.nl>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that we have struct fwnode_handle, we can use that to point to
ACPI companions from struct device objects instead of pointing to
struct acpi_device directly.
There are two benefits from that. First, the somewhat ugly and
hackish struct acpi_dev_node can be dropped and, second, the same
struct fwnode_handle pointer can be used in the future to point
to other (non-ACPI) firmware device node types.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
The macro BANK_OFF which calculates the base offset for each GPIO port.
The macro is needlessly complex and unreadable. Simplify the
calculation to a simple math operation.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: linux-gpio@vger.kernel.org
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds a new driver for Altera soft GPIO IP. The driver is able to do
read/write and allows GPIO to be a interrupt controller.
Tested on Altera GHRD on interrupt handling and IO.
v10:
- Updated conflicting device tree parameters
- Removed unused headers
- Used macro instead of magic numbers for ngpio
- Code readability cleanup using ?: and temporal variables
- Removed leftover garbage and unnecessary function calls
- Checked bgpio_init but unusable because Altera GPIO may not
be a multiple of 8 bits
v9:
- Removed duplicated initialization on set_type using temporals
to improve code readability in calling generic_handle_irq
- Using ?: ternary to reduce code size
v8:
- Using for_each_set_bit
- Added const for struct definition
- Removed naggy pr_err
- Sort alpha header
- Remove unused macros
- Use fixed width data types instead of unsigned long
- Whitespace issue fixes
- Removed _relaxed function for better compatibility across different
CPU
- Changed irq_create_mapping to platform_get_irq updated implementation
to use gpiochip_irqchip_add
- Reserve interrupt-cells number 2 in device tree binding for future
use
- Remove confusing sections on devicetree bindings
- Added tristate Kconfig help text
v7:
- Used dev_warn instead of pr_warn
- Clean up unnecesarry if else indentation
v6:
- Added irq_startup and irq_shutdown
- Changed bitwise clamping style
- Cleanup bitwise operation to improve readability change naming of
mapped irqs from virq to mapped_irq
v5:
- Dispose irq_domain mapping correctly
- Update optional binding description in binding docs
v4:
- Added vendor prefix to devicetree binding for IP specific properties
using MMIO GPIO helper library instead of manually map PIO to memory
- altera_gpio_chip inline struct documentation to kerneldoc
- Using dev_ print to print a better failure message
v2, v3:
- Do not reference NO_IRQ
- Updated irq_set_type to only allow the hardware configured irq type
Signed-off-by: Tien Hock Loh <thloh@altera.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 98686d9a52 ("gpio: mpc8xxx: Convert to platform device
interface"), we get the following section mismatch warning. Remove the
__initdata annotation to fix it.
WARNING: vmlinux.o(.data+0xbc28): Section mismatch in reference from the variable mpc8xxx_plat_driver to the variable .init.data:mpc8xxx_gpio_ids
The variable mpc8xxx_plat_driver references
the variable __initdata mpc8xxx_gpio_ids
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add device managed variants of gpiod_get_array() / gpiod_put_array()
functions for conveniently obtaining and disposing of an entire array
of GPIOs with one function call.
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce new functions for conveniently obtaining and disposing of
an entire array of GPIOs with one function call.
ACPI parts tested by Mika Westerberg, DT parts tested by Rojhalat
Ibrahim.
Change log:
v5: move the ACPI functions to gpiolib-acpi.c
v4: - use shorter names for members of struct gpio_descs
- rename lut_gpio_count to platform_gpio_count for clarity
- add check for successful memory allocation
- use ERR_CAST()
v3: - rebase on current linux-gpio devel branch
- fix ACPI GPIO counting
- allow for zero-sized arrays
- make the flags argument mandatory for the new functions
- clarify documentation
v2: change interface
Suggested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Avoid multiple identical definitions of the gpio suffix strings by putting
them into a global constant array.
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio binding document says that new code should always use named
gpios. Patch 40b73183 added support to parse a list of gpios from child
nodes, but does not make it possible to use named gpios. This patch adds
the con_id property and implements it is done in gpiolib.c, where the
old-style of using unnamed gpios still works.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Bryan Wu <cooloney@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pcf857x GPIO and interrupt controller uses dummy_irq_chip, which
does not implement irq_chip.irq_set_wake() and does not set
IRQCHIP_SKIP_SET_WAKE.
This causes two s2ram issues if wake-up is enabled for the pcf857x GPIO
pins:
1. During resume from s2ram, the following warning is printed:
WARNING: CPU: 0 PID: 1046 at kernel/irq/manage.c:537 irq_set_irq_wake+0x9c/0xf8()
Unbalanced IRQ 113 wake disable
2. Wake-up through the pcf857x GPIO pins may fail, as the parent
interrupt controller may be suspended.
Migrate the pcf857x GPIO and interrupt controller from dummy_irq_chip to
its own irq_chip. This irq chip implements irq_chip.irq_set_wake() to
propagate its wake-up setting to the parent interrupt controller.
This fixes wake-up through gpio-keys on sh73a0/kzm9g, where the pcf857x
interrupt is cascaded to irq-renesas-intc-irqpin, and the latter must
not be suspended when wake-up is enabled.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Switch the PCF857x GPIO driver to use the gpiolib irqchip helpers.
This driver uses a nested threaded interrupt, hence handle_nested_irq()
and gpiochip_set_chained_irqchip() must be used.
Note that this removes the checks added in commit 21fd3cd187
("gpio: pcf857x: call the gpio user handler iff gpio_to_irq is done"),
as the interrupt mappings are no longer created on-demand by the driver,
but by gpiochip_irqchip_add() during initialization.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on Boris Brezillion's work this is a reworked patch
of his initial GPIO hogging mechanism.
This patch provides a way to initially configure specific GPIO
when the GPIO controller is probed.
The actual DT scanning to collect the GPIO specific data is performed
as part of gpiochip_add().
The purpose of this is to allow specific GPIOs to be configured
without any driver specific code.
This is particularly useful because board design are getting
increasingly complex and given SoC pins can now have more
than 10 mux values, a lot of connections are now dependent on
external IO muxes to switch various modes.
Specific drivers should not necessarily need to be aware of
what accounts to a specific board implementation. This board level
"description" should be best kept as part of the dts file.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Take a sweep to bring the irq support for the MAX732x expanders
into the gpiolib core to cut down on duplicated code.
Only compile tested! I need some feedback from people using this
expander with interrupts to tell me if things go right or
wrong when I do this.
Cc: Semen Protsenko <semen.protsenko@globallogic.com>
Cc: Mans Rullgard <mans@mansr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The gpio_chip operations receive a pointer the gpio_chip struct which is
contained in the driver's private struct, yet the container_of call in those
functions point to the mfd struct defined in include/linux/mfd/tps65912.h.
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The change:
7b8792bbdf
gpiolib: of: Correct error handling in of_get_named_gpiod_flags
assumed that only one gpio-chip is registred per of-node.
Some drivers register more than one chip per of-node, so
adjust the matching function of_gpiochip_find_and_xlate to
not stop looking for chips if a node-match is found and
the translation fails.
Cc: Stable <stable@vger.kernel.org>
Fixes: 7b8792bbdf ("gpiolib: of: Correct error handling in of_get_named_gpiod_flags")
Signed-off-by: Hans Holmberg <hans.holmberg@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Tyler Hall <tylerwhall@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull ARM updates from Russell King:
- clang assembly fixes from Ard
- optimisations and cleanups for Aurora L2 cache support
- efficient L2 cache support for secure monitor API on Exynos SoCs
- debug menu cleanup from Daniel Thompson to allow better behaviour for
multiplatform kernels
- StrongARM SA11x0 conversion to irq domains, and pxa_timer
- kprobes updates for older ARM CPUs
- move probes support out of arch/arm/kernel to arch/arm/probes
- add inline asm support for the rbit (reverse bits) instruction
- provide an ARM mode secondary CPU entry point (for Qualcomm CPUs)
- remove the unused ARMv3 user access code
- add driver_override support to AMBA Primecell bus
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (55 commits)
ARM: 8256/1: driver coamba: add device binding path 'driver_override'
ARM: 8301/1: qcom: Use secondary_startup_arm()
ARM: 8302/1: Add a secondary_startup that assumes ARM mode
ARM: 8300/1: teach __asmeq that r11 == fp and r12 == ip
ARM: kprobes: Fix compilation error caused by superfluous '*'
ARM: 8297/1: cache-l2x0: optimize aurora range operations
ARM: 8296/1: cache-l2x0: clean up aurora cache handling
ARM: 8284/1: sa1100: clear RCSR_SMR on resume
ARM: 8283/1: sa1100: collie: clear PWER register on machine init
ARM: 8282/1: sa1100: use handle_domain_irq
ARM: 8281/1: sa1100: move GPIO-related IRQ code to gpio driver
ARM: 8280/1: sa1100: switch to irq_domain_add_simple()
ARM: 8279/1: sa1100: merge both GPIO irqdomains
ARM: 8278/1: sa1100: split irq handling for low GPIOs
ARM: 8291/1: replace magic number with PAGE_SHIFT macro in fixup_pv code
ARM: 8290/1: decompressor: fix a wrong comment
ARM: 8286/1: mm: Fix dma_contiguous_reserve comment
ARM: 8248/1: pm: remove outdated comment
ARM: 8274/1: Fix DEBUG_LL for multi-platform kernels (without PL01X)
ARM: 8273/1: Seperate DEBUG_UART_PHYS from DEBUG_LL on EP93XX
...
- GPIOLIB core changes:
- Create and use of_mm_gpiochip_remove() for removing
memory-mapped OF GPIO chips
- GPIO MMIO library suppports bgpio_set_multiple for
switching several lines at once, a feature merged in
the last cycle.
- New drivers:
- New driver for the APM X-gene standby GPIO controller
- New driver for the Fujitsu MB86S7x GPIO controller
- Cleanups:
- Moved rcar driver to use gpiolib irqchip
- Moxart converted to the GPIO MMIO library
- GE driver converted to GPIO MMIO library
- Move sx150x to irqdomain
- Move max732x to irqdomain
- Move vx855 to use managed resources
- Move dwapb to use managed resources
- Clean tc3589x from platform data
- Clean stmpe driver to use device tree only probe
- New subtypes:
- sx1506 support in the sx150x driver
- Quark 1000 SoC support in the SCH driver
- Support X86 in the Xilinx driver
- Support PXA1928 in the PXA driver
- Extended drivers:
- max732x supports device tree probe
- sx150x supports device tree probe
- Various minor cleanups and bug fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJU2W1HAAoJEEEQszewGV1zuRkQAKBukQwx46zQuFH8oalSuxmy
H2/ESMnDmRlBI0zX+dAGDg4HlkO9VwIrdcyzMMe7uO8EFUu9d4/mu2E1f8cY2mxu
kwUSntVaYGVPVj/Vok3kzq1wW/pUQ9E2iMbNeDVZJH/cqEvylPPa2LZ3hZVri57J
orJzaYtZWf640y3McGTUDwIQokgxxdMMyWfm26P1iZkByjofUaYRHS1NIxhKVSVC
Y6uA/Ivvh56ezlPQykc7m6YEjoUS91AMllJca1A3KF3+qvQ3Hnc+i9mB7hAQbJ8L
6Iv2qCD4TgtWT5YXgP0eZsfSV/19kvlVlGX7QQT6o7uIFOLVNOmX9FJAc4n3SGNI
HbxsDdlF9XHVFh0XyKcBQfg0uUmRWUDQ/LsXn9KL6Yrpyx3QZGH/PTYl/XoCj1IO
IL6Bw51FCBXvCvLP5alXMouosAxrc19YpljcAuAMmjVTXe6RoULOZJs+lhTHMhvj
S6FWr6l0XDr4yKb0SXTOGI4hvRJvL8SWnIt5ezZrNrTKLsklL3Bi/o3BoKzzxmqS
6l/rxvcVUov455IrfqJ0ZEM6ZxC9/cvGec0RFyglopNSlKeTQsgWRNa6Pw2xZVk8
orT+G3L4jZ1+0hcjcSwfvHng5Nv6DuhIfUNPbLF/ZzmJcBPqGc/DuhGkFqOrBaXg
ey7Lua6+l+8zcDtugRRG
=yWrB
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the GPIO bulk changes for the v3.20 series:
GPIOLIB core changes:
- Create and use of_mm_gpiochip_remove() for removing memory-mapped
OF GPIO chips
- GPIO MMIO library suppports bgpio_set_multiple for switching
several lines at once, a feature merged in the last cycle.
New drivers:
- New driver for the APM X-gene standby GPIO controller
- New driver for the Fujitsu MB86S7x GPIO controller
Cleanups:
- Moved rcar driver to use gpiolib irqchip
- Moxart converted to the GPIO MMIO library
- GE driver converted to GPIO MMIO library
- Move sx150x to irqdomain
- Move max732x to irqdomain
- Move vx855 to use managed resources
- Move dwapb to use managed resources
- Clean tc3589x from platform data
- Clean stmpe driver to use device tree only probe
New subtypes:
- sx1506 support in the sx150x driver
- Quark 1000 SoC support in the SCH driver
- Support X86 in the Xilinx driver
- Support PXA1928 in the PXA driver
Extended drivers:
- max732x supports device tree probe
- sx150x supports device tree probe
Various minor cleanups and bug fixes"
* tag 'gpio-v3.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (61 commits)
gpio: kconfig: replace PPC_OF with PPC
gpio: pxa: add PXA1928 gpio type support
dt/bindings: gpio: add compatible string for marvell,pxa1928-gpio
gpio: pxa: remove mach IRQ includes
gpio: max732x: use an inline function for container cast
gpio: use sizeof() instead of hardcoded values
gpio: max732x: add set_multiple function
gpio: sch: Consolidate similar algorithms
gpio: tz1090-pdc: Use resource_size to fix off-by-one resource size calculation
gpio: ge: Convert to use devm_kstrdup
gpio: correctly use const char * const
gpio: sx150x: fixup OF support
gpio: mpc8xxx: Use of_mm_gpiochip_remove
gpio: Add Fujitsu MB86S7x GPIO driver
gpio: mpc8xxx: Convert to platform device interface.
gpio: zevio: Use of_mm_gpiochip_remove
gpio: gpio-mm-lantiq: Use of_mm_gpiochip_remove
gpio: gpio-mm-lantiq: Use of_property_read_u32
gpio: gpio-mm-lantiq: Do not replicate code
gpio :gpio-mm-lantiq: Use devm_kzalloc
...
The PPC_OF is a ppc specific option which is used to mean that the
firmware device tree access functions are available. Since all the
ppc platforms have a device tree, it is aways set to 'y' for ppc.
So it makes no sense to keep a such option in the current kernel.
Replace it with PPC.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for PXA1928 GPIOs. The PXA1928 adds a 6th bank from previous
generations.
Signed-off-by: Jing Xiang <jxiang@marvell.com>
Signed-off-by: Xiangzhan Meng <mengxzh@marvell.com>
[robh: ported to 3.19 from vendor kernel]
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In preparation to enable ARCH_MMP on ARM64, the include of mach/irqs.h
must be eliminated. mach/irqs.h was being included for IRQ_GPIO{0,1},
but these IRQs are always passed in as resources now. We can use irq0
and irq1 and get rid of IRQ_GPIOx. Get rid of the ifdef in the process
as it is no longer needed.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cast the struct gpio_chip into a max732x_chip using an inline
macro and move the assignment to the variable declaration
to save lines and simplify things.
Cc: Semen Protsenko <semen.protsenko@globallogic.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiolib uses a fixed string for the suffixes and defines it at 32 bytes.
Later in the code snprintf is used with this fixed value of 32. Using
sizeof() is safer in case the size for the suffixes is ever changed.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a set_multiple function to the MAX732x GPIO driver,
allowing for performance gains when using gpiod_set_array().
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix memory leak in the gpio sysfs interface due to failure to drop
reference to device returned by class_find_device when setting the
gpio-line polarity.
Fixes: 0769746183 ("gpiolib: add support for changing value polarity
in sysfs")
Cc: stable <stable@vger.kernel.org> # v2.6.33
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix memory leak in the gpio sysfs interface due to failure to drop
reference to device returned by class_find_device when creating a link.
Fixes: a4177ee7f1 ("gpiolib: allow exported GPIO nodes to be named
using sysfs links")
Cc: stable <stable@vger.kernel.org> # v2.6.32
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As a part of driver consolidation, move GPIO-related IRQ code to
drivers/gpio/gpio-sa1100.c. The code does not use GPIOLIB_IRQCHIP (yet),
because sa1100 does not have a device for gpios, which is a requirement
for GPIOLIB_IRQCHIP. This will be the next step.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Low GPIO pins use an interrupt in SC interrupts space. However it's
possible to handle them as if all the GPIO interrupts are instead tied
to single GPIO handler, which later decodes GEDR register and
chain-calls next IRQ handler. So split first 11 interrupts into system
part (IRQ_GPIO0_SC - IRQ_GPIO10_SC) which work exactly like the rest of
system controller interrupts and real GPIO interrupts
(IRQ_GPIO0..IRQ_GPIO10). A single handler sa1100_gpio_handler then
decodes and calls next handler.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Consolidating similar algorithms into common functions to make
GPIO SCH simpler and manageable.
Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_kstrdup to simplify the error handling path.
Also return -ENOMEM instead of 0 if devm_kstrdup fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On my previous patch I was overly hasty and made the suffixes string
array
const char const *suffixes, instaed of const char * const suffixes. This
patch corrects that
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Create default gpio base if neither device node nor
platform data is defined.
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Antonio Fiol <antonio@fiol.es>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Similar to omap_gpio_irq_type() let's make sure that the GPIO
is usable as an interrupt if the platform init code did not
call gpio_request(). Otherwise we can get invalid device access
after setup_irq():
WARNING: CPU: 0 PID: 1 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x214/0x340()
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4CFG (Idle): Data Access in Supervisor mode during Functional access
...
[<c05f21e4>] (__irq_svc) from [<c05f1974>] (_raw_spin_unlock_irqrestore+0x34/0x44)
[<c05f1974>] (_raw_spin_unlock_irqrestore) from [<c00914a8>] (__setup_irq+0x244/0x530)
[<c00914a8>] (__setup_irq) from [<c00917d4>] (setup_irq+0x40/0x8c)
[<c00917d4>] (setup_irq) from [<c0039c8c>] (omap_system_dma_probe+0x1d4/0x2b4)
[<c0039c8c>] (omap_system_dma_probe) from [<c03b2200>] (platform_drv_probe+0x44/0xa4)
...
We can fix this the same way omap_gpio_irq_type() is handling it.
Note that the long term solution is to change the gpio-omap driver
to handle the banks as separate driver instances. This will allow
us to rely on just runtime PM for tracking the bank specific state.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make OF conditional on CONFIG_OF_GPIO, rename and register
the match table.
Reported-by: Mike Krinkin <krinkin.m.u@gmail.com>
Cc: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since d621e8bae5 (Create of_mm_gpiochip_remove), there is a
counterpart for of_mm_gpiochip_add.
This patch implements the remove function of the driver making use of
it.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Driver for Fujitsu MB86S7x SoCs that have a memory mapped GPIO controller.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com>
Signed-off-by: Tetsuya Nuriya <nuriya.tetsuya@jp.fujitsu.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This way we do not need to transverse the device tree manually.
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since d621e8bae5 (Create of_mm_gpiochip_remove), there is a
counterpart for of_mm_gpiochip_add.
This patch implements the remove function of the driver making use of
it.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Fabian Vogt <fabian@ritter-vogt.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since d621e8bae5 (Create of_mm_gpiochip_remove), there is a
counterpart for of_mm_gpiochip_add.
This patch implements the remove function of the driver making use of
it.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: John Crispin <blogic@openwrt.org>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of parsing manually the shadow content, use the much simpler
helper of_property_read_u32.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: devicetree@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since d621e8bae5 (Create of_mm_gpiochip_remove), there is a
counterpart for of_mm_gpiochip_add.
This patch implements the remove function of the driver making use of
it.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Require that device tree be used with STMPE (all platforms use this)
and enforce OF_GPIO, then delete the platform data.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Driver for standby GPIO controller of APM X-Gene SoCs on arm64.
Signed-off-by: Y Vo <yvo@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current sx150x gpio expander driver doesn't support
DTS. Now we added dts support for this driver.
Signed-off-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add set_multiple functions to the generic driver for memory-mapped GPIO
controllers to improve performance when setting multiple outputs
simultaneously.
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit ffe4770b9b ("gpio-amd8111: check ioport_map return value")
adds the error check on ioport_map(). It doesnt release the requested region.
On failure this patch release the region that has requested before.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Reported-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Include linux/slab.h to fix following compilation error.
drivers/gpio/gpio-ge.c: In function ‘gef_gpio_probe’:
drivers/gpio/gpio-ge.c:95:2: error: implicit declaration of function ‘kfree’ [-Werror=implicit-function-declaration]
kfree(bgc->gc.label);
Signed-off-by: Kamlakant Patel <kamlakant.patel@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
that have been around forever in the GPIO subsystem, most of them
also tagged for stable:
- A large slew of fixes from Johan Hovold who is finally testing and
reviewing the removal path of the GPIO drivers.
- Fix of_get_named_gpiod_flags() so it works as expected.
- Fix an IRQ handling bug in the crystalcove driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ekXq
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here is a set of fixes that mainly appeared when Johan Hovold started
exercising the removal path of the GPIO library, dealing with
hotplugging of GPIO controllers. Details from tag:
A slew of fixes dealing with some irritating bugs (non-regressions)
that have been around forever in the GPIO subsystem, most of them also
tagged for stable:
- A large slew of fixes from Johan Hovold who is finally testing and
reviewing the removal path of the GPIO drivers.
- Fix of_get_named_gpiod_flags() so it works as expected.
- Fix an IRQ handling bug in the crystalcove driver"
* tag 'gpio-v3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpiolib: of: Correct error handling in of_get_named_gpiod_flags
gpio: sysfs: fix gpio attribute-creation race
gpio: sysfs: fix gpio device-attribute leak
gpio: sysfs: fix gpio-chip device-attribute leak
gpio: unregister gpiochip device before removing it
gpio: fix sleep-while-atomic in gpiochip_remove
gpio: fix memory leak and sleep-while-atomic
gpio: clean up gpiochip_add error handling
gpio: fix gpio-chip list corruption
gpio: fix memory and reference leaks in gpiochip_add error path
gpio: crystalcove: use handle_nested_irq
of_get_named_gpiod_flags fails with -EPROBE_DEFER in cases
where the gpio chip is available and the GPIO translation fails.
This causes drivers to be re-probed erroneusly, and hides the
real problem(i.e. the GPIO number being out of range).
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Hans Holmberg <hans.holmberg@intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix the coding style issue by adding a blank line after declaration
Signed-off-by: Mohammad Jamal <md.jamalmohiuddin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
X86 Kconfig symbol is X86, not ARCH_X86.
Fixes: c586b3075d5b47d8 (gpio/xilinx: Add support for X86 Arch)
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Switch the R-Car Gen2 GPIO driver to use the gpiolib irqchip helpers.
While doing this also make sure that gpiochip_irqchip_add() is called
after the gpiochip itself is registered, as required.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the call to devm_kzalloc() fails, nothing must be cleant up.
This was missed before because gpio_rcar_probe() had a "return"
statement after the first "goto err0".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: df0c6c8023 ("gpio: rcar: Add minimal runtime PM support")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Ensure that when there is an error during probe that the gpiochip is
removed and the generic irq chip is removed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Wrap some long lines.
Prefer seq_puts() over seq_printf().
space to tab conversions.
Spelling error fix.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Checkpatch complains, and probably with good reason that we should use
const char const * for the static constant array that never gets
changed.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ioport_map() may fail. Its safe to check the return value.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use resource managed APIs to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use resource_size to fix off-by-one resource size calculation
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
"gc->ngpio" is a number between 1 and GRGPIO_MAX_NGPIO. If "offset" is
GRGPIO_MAX_NGPIO then we're going one step beyond the end of the
priv->lirqs[] array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This device is only used from the device tree, and the startup()
and remove() callbacks are not used anywhere in the kernel, so
retire them and the pdata altogether.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_* APIs to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the newly created of_mm_gpiochip_remove function for cleaning up
of_mm_gpiochip_add
Suggested-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Create counterpart of of_mm_gpiochip_add(). This way the modules that
can be removable do not duplicate the cleanup code.
Suggested-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, we had two gpio chips on cores configured as dual.
This lead to mapping the same memory region twice and duplicating the
init and remove code.
This patch creates a single gpiochip for single and dual cores.
Suggested-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some documentation were not following the kernel-doc format.
Backporting patch from Xilinx git repository.
Suggested-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core can be accessed via PCIe on X86 platform.
This patch also allows the driver to be used as module.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This way we do not need to transverse the device tree manually and we
support hot plugged devices.
Also Implement remove callback so the driver can be unloaded
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of calculating the register offset per call, pre-calculate it on
probe time.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Intel Quark X1000 provides a total of 16 GPIOs. The GPIOs are split between
the legacy I/O bridge and the GPIO controller.
GPIO-SCH is the GPIO pins on legacy bridge for Intel Quark SoC.
Intel Quark X1000 has 2 GPIOs powered by the core power well and 6 from
the suspend power well.
This piece of work is derived from Dan O'Donovan's initial work for Quark
X1000 enabling.
Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
semtech has two series of sx150x gpio expanders: sx150x-456 and
sx150x-789.
The current gpio-150x driver in linux only support sx1508 and
sx1509.
We added sx1506 support code into this driver.
Signed-off-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sx150x gpio driver used a loop to set liner irq map for gpio pins.
Now we use the irq domain to rebuild this irq mappig and make sure the
codes are still compatible to old users.
this patch also adds IRQF_ONESHOT flag to fix the IRQ flooding issues.
Signed-off-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
[Make Kconfig select GPIOLIB_IRQCHIP]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix attribute-creation race with userspace by using the default group
to create also the contingent gpio device attributes.
Fixes: d8f388d8dc ("gpio: sysfs interface")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio device attributes were never destroyed when the gpio was
unexported (or on export failures).
Use device_create_with_groups() to create the default device attributes
of the gpio class device. Note that this also fixes the
attribute-creation race with userspace for these attributes.
Remove contingent attributes in export error path and on unexport.
Fixes: d8f388d8dc ("gpio: sysfs interface")
Cc: stable <stable@vger.kernel.org> # v2.6.27+
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio-chip device attributes were never destroyed when the device was
removed.
Fix by using device_create_with_groups() to create the device attributes
of the chip class device.
Note that this also fixes the attribute-creation race with userspace.
Fixes: d8f388d8dc ("gpio: sysfs interface")
Cc: stable <stable@vger.kernel.org> # v2.6.27+
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Unregister gpiochip device (used to export information through sysfs)
before removing it internally. This way removal will reverse addition.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move direct and indirect calls to gpiochip_remove_pin_ranges outside of
spin lock as they can end up taking a mutex in pinctrl_remove_gpio_range.
Note that the pin ranges are already added outside of the lock.
Fixes: 9ef0d6f762 ("gpiolib: call pin removal in chip removal function")
Fixes: f23f1516b6 ("gpiolib: provide provision to register pin ranges")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix memory leak and sleep-while-atomic in gpiochip_remove.
The memory leak was introduced by afa82fab5e ("gpio / ACPI: Move event
handling registration to gpiolib irqchip helpers") that moved the
release of acpi interrupt resources to gpiochip_irqchip_remove, but by
then the resources are no longer accessible as the acpi_gpio_chip has
already been freed by acpi_gpiochip_remove.
Note that this also fixes a few potential sleep-while-atomics, which has
been around since 1425052097 ("gpio: add IRQ chip helpers in gpiolib")
when the call to gpiochip_irqchip_remove while holding a spinlock was
added (a couple of irq-domain paths can end up grabbing mutexes).
Fixes: afa82fab5e ("gpio / ACPI: Move event handling registration to
gpiolib irqchip helpers")
Fixes: 1425052097 ("gpio: add IRQ chip helpers in gpiolib")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix potential corruption of gpio-chip list due to failure to remove the
chip from the list before returning in gpiochip_add error path.
The chip could be long gone when the global list is next traversed,
something which could lead to a null-pointer dereference. In the best
case (chip not deallocated) we are just leaking the gpio range.
Fixes: 14e85c0e69 ("gpio: remove gpio_descs global array")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Memory allocated and references taken by of_gpiochip_add and
acpi_gpiochip_add were never released on errors in gpiochip_add (e.g.
failure to find free gpio range).
Fixes: 391c970c0d ("of/gpio: add default of_xlate function if device
has a node pointer")
Fixes: 664e3e5ac6 ("gpio / ACPI: register to ACPI events
automatically")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the irq_chip bus_sync_unlock method to update hardware registers
instead of scheduling work from the mask/unmask methods. This simplifies
a bit the driver and make it more uniform with the other GPIO IRQ
drivers.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
irqmap is optional property, so priv->domain can be NULL if !irqmap.
Thus add NULL test for priv->domain before calling irq_domain_remove()
to prevent NULL pointer dereference.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
dln2_gpio_direction_output() ignored the state passed into it. Fix it.
Also make dln2_gpio_pin_set_out_val return int, so we can check the error value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Daniel Baluta <daniel.baluta@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As noticed during suspend/resume operations, the IRQ can be unmasked
then disabled in suspend and eventually enabled in resume, but without
being unmasked.
The current implementation does not take into account interactions
between mask/unmask and enable/disable interrupts, and thus in the
above scenarios the IRQs remain unactive.
To fix this we removed the enable/disable operations as they fallback
to mask/unmask anyway.
We also remove the pending bitmaks as it is already done in irq_data
(i.e. IRQS_PENDING).
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
- A new API that allows setting more than one GPIO at the
time. This is implemented for the new descriptor-based
API only and makes it possible to e.g. toggle a clock and
data line at the same time, if the hardware can do this
with a single register write. Both consumers and drivers
need new calls, and the core will fall back to driving
individual lines where needed. Implemented for the MPC8xxx
driver initially.
- Patched the mdio-mux-gpio and the serial mctrl driver
that drives modems to use the new multiple-setting API
to set several signals simultaneously.
- Get rid of the global GPIO descriptor array, and instead
allocate descriptors dynamically for each GPIO on a certain
GPIO chip. This moves us closer to getting rid of the
limitation of using the global, static GPIO numberspace.
- New driver and device tree bindings for 74xx ICs.
- New driver and device tree bindings for the VF610 Vybrid.
- Support the RCAR r8a7793 and r8a7794.
- Guidelines for GPIO device tree bindings trying to get
things a bit more strict with the advent of combined
device properties.
- Suspend/resume support for the MVEBU driver.
- A slew of minor fixes and improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZAhA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull take two of the GPIO updates:
"Same stuff as last time, now with a fixup patch for the previous
compile error plus I ran a few extra rounds of compile-testing.
This is the bulk of GPIO changes for the v3.19 series:
- A new API that allows setting more than one GPIO at the time. This
is implemented for the new descriptor-based API only and makes it
possible to e.g. toggle a clock and data line at the same time, if
the hardware can do this with a single register write. Both
consumers and drivers need new calls, and the core will fall back
to driving individual lines where needed. Implemented for the
MPC8xxx driver initially
- Patched the mdio-mux-gpio and the serial mctrl driver that drives
modems to use the new multiple-setting API to set several signals
simultaneously
- Get rid of the global GPIO descriptor array, and instead allocate
descriptors dynamically for each GPIO on a certain GPIO chip. This
moves us closer to getting rid of the limitation of using the
global, static GPIO numberspace
- New driver and device tree bindings for 74xx ICs
- New driver and device tree bindings for the VF610 Vybrid
- Support the RCAR r8a7793 and r8a7794
- Guidelines for GPIO device tree bindings trying to get things a bit
more strict with the advent of combined device properties
- Suspend/resume support for the MVEBU driver
- A slew of minor fixes and improvements"
* tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (33 commits)
gpio: mcp23s08: fix up compilation error
gpio: pl061: document gpio-ranges property for bindings file
gpio: pl061: hook request if gpio-ranges avaiable
gpio: mcp23s08: Add option to configure IRQ output polarity as active high
gpio: fix deferred probe detection for legacy API
serial: mctrl_gpio: use gpiod_set_array function
mdio-mux-gpio: Use GPIO descriptor interface and new gpiod_set_array function
gpio: remove const modifier from gpiod_get_direction()
gpio: remove gpio_descs global array
gpio: mxs: implement get_direction callback
gpio: em: Use dynamic allocation of GPIOs
gpio: Check if base is positive before calling gpio_is_valid()
gpio: mcp23s08: Add simple IRQ support for SPI devices
gpio: mcp23s08: request a shared interrupt
gpio: mcp23s08: Do not free unrequested interrupt
gpio: rcar: Add r8a7793 and r8a7794 support
gpio-mpc8xxx: add mpc8xxx_gpio_set_multiple function
gpiolib: allow simultaneous setting of multiple GPIO outputs
gpio: mvebu: add suspend/resume support
gpio: gpio-davinci: remove duplicate check on resource
..
The driver depends on the chip.of_node being present to compile,
which is the case on some target platforms but not others.
Instead, rely on chip.dev->of_node to be used, as struct device
always has an of_node in place.
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Force conversion of the ux500 pin control device trees
and parsers to use the generic pin control bindings.
- New driver and device tree bindings for the Qualcomm
PMIC MPP pin controller and GPIO.
- Some ACPI infrastructure for pin controllers.
- New driver for the Intel CherryView/Braswell pin controller,
the first Intel pin controller to fully take advantage of
the pin control subsystem.
- Support the Freescale i.MX VF610 variant.
- Support the sunxi A80 variant.
- Support the Samsung Exynos 4415 and Exynos 7 variants.
- Split out Intel pin controllers to their own subdirectory.
- A large slew of rockchip pin control updates, including
suspend/resume support.
- A large slew of Samsung Exynos pin controller updates.
- Various minor updates and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sxpe
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
"Here is a stash of pin control changes I have collected for the v3.19
series. Mainly new hardware support, with Intels new embedded SoC as
the especially interesting thing standing out, fully using the
subsystem.
- Force conversion of the ux500 pin control device trees and parsers
to use the generic pin control bindings.
- New driver and device tree bindings for the Qualcomm PMIC MPP pin
controller and GPIO.
- Some ACPI infrastructure for pin controllers.
- New driver for the Intel CherryView/Braswell pin controller, the
first Intel pin controller to fully take advantage of the pin
control subsystem.
- Support the Freescale i.MX VF610 variant.
- Support the sunxi A80 variant.
- Support the Samsung Exynos 4415 and Exynos 7 variants.
- Split out Intel pin controllers to their own subdirectory.
- A large slew of rockchip pin control updates, including
suspend/resume support.
- A large slew of Samsung Exynos pin controller updates.
- Various minor updates and fixes"
* tag 'pinctrl-v3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (49 commits)
pinctrl: at91: enhance (debugfs) at91_gpio_dbg_show
pinctrl: meson: add device tree bindings documentation
gpio: tz1090: Fix error handling of irq_of_parse_and_map
pinctrl: tz1090-pinctrl.txt: Fix typo in binding
pinctrl: pinconf-generic: Declare dt_params/conf_items const
pinctrl: exynos: Add support for Exynos4415
pinctrl: exynos: Add initial driver data for Exynos7
pinctrl: exynos: Add irq_chip instance for Exynos7 wakeup interrupts
pinctrl: exynos: Consolidate irq domain callbacks
pinctrl: exynos: Generalize the eint16_31 demux code
pinctrl: samsung: Separate per-bank init and runtime data
pinctrl: samsung: Constify samsung_pin_ctrl struct
pinctrl: samsung: Constify samsung_pin_bank_type struct
pinctrl: samsung: Drop unused label field in samsung_pin_ctrl struct
pinctrl: samsung: Make samsung_pinctrl_get_soc_data use ERR_PTR()
pinctrl: Add Intel Cherryview/Braswell pin controller support
gpio / ACPI: Add knowledge about pin controllers to acpi_get_gpiod()
pinctrl: Fix path error in documentation
pinctrl: rockchip: save and restore gpio6_c6 pinmux in suspend/resume
pinctrl: rockchip: add suspend/resume functions
...
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in drivers/gpio/gpio-omap.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The SET_PM_RUNTIME_PM_OPS() and SET_RUNTIME_PM_OPS() macros are
identical except that one of them is not empty for CONFIG_PM set,
while the other one is not empty for CONFIG_PM_RUNTIME set,
respectively.
However, after commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so one
of these macros is now redundant.
For this reason, replace SET_PM_RUNTIME_PM_OPS() with
SET_RUNTIME_PM_OPS() everywhere and redefine the SET_PM_RUNTIME_PM_OPS
symbol as SET_RUNTIME_PM_OPS in case new code is starting to use the
macro being removed here.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Gpio-ranges property is useful to represent which GPIOs correspond
to which pins on which pin controllers. But there may be some gpios
without pinctrl operation. So check whether gpio-ranges property
exists in device node first.
Signed-off-by: Yunlei He <heyunlei@huawei.com>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Default is active low, but if property is specified in DT set INTPOL flag.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 14e85c0e69 ("gpio: remove gpio_descs global array") changed
gpio_to_desc()'s behavior to return NULL not only for GPIOs numbers
not in the valid range, but also for all GPIOs whose controller has not
been probed yet. Although this behavior is more correct (nothing hints
that these GPIO numbers will be populated later), this affects
gpio_request() and gpio_request_one() which call gpiod_request() with a
NULL descriptor, causing it to return -EINVAL instead of the expected
-EPROBE_DEFER for a non-probed GPIO.
gpiod_request() is only called with a descriptor obtained from
gpio_to_desc() from these two functions, so address the issue there.
Other ways to obtain GPIOs rely on well-defined mappings and can thus
return -EPROBE_DEFER only for relevant GPIOs, and are thus not affected
by this issue.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Although gpiod_get_direction() can be considered side-effect free for
consumers, its internals involve setting or clearing bits in the
affected GPIO descriptor, for which we need to force-cast the const
descriptor variable to non-const. This could lead to incorrect behavior
if the compiler decides to optimize here, so remove this const
attribute. The intent is to make gpiod_get_direction() private anyway,
so it does not really matter.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace the ARCH_NR_GPIOS-sized static array of GPIO descriptors by
dynamically-allocated arrays for each GPIO chip.
This change makes gpio_to_desc() perform in O(n) (where n is the number
of GPIO chips registered) instead of O(1), however since n is rarely
bigger than 1 or 2 no noticeable performance issue is expected.
Besides this provides more incentive for GPIO consumers to move to the
gpiod interface. One could use a O(log(n)) structure to link the GPIO
chips together, but considering the low limit of n the hypothetical
performance benefit is probably not worth the added complexity.
This patch uses kcalloc() in gpiochip_add(), which removes the ability
to add a chip before kcalloc() can operate. I am not aware of such
cases, but if someone bisects up to this patch then I will be proven
wrong...
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiolib's gpiod_get_direction() function returns the EINVAL error
if .get_direction callback is not defined.
The patch implements the callback for mxs chip which is useful
for debugging.
Inspired by arch/arm/mach-at91/gpio.c
On the moment the patch is required to get the patch
"serial: mxs-auart: enable PPS support" working.
It is planned to introduce new mctrl_gpio helpers to avoid
gpiod_get_direction() function.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use dynamic allocation of GPIOs instead of looking at the gpio%u alias
in DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It doesn't make much sense to make some (possible expensive) calls to
gpio_is_valid() first, and to ignore the result if the base number is
negative. Check for a positive base number first.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently this implementation only supports one IRQ for (all) SPI devices
using the same chip select.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Request a shared interrupt when requesting a mcp23s08 GPIO interrupt.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If devm_request_threaded_irq fails for some reason we call
mcp23s08_irq_teardown afterwards.
Do not free the unrequested interrupt in this case. free_irq can also be
omitted for the error free case because we use devm_request_threaded_irq.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a set_multiple function to the MPC8xxx GPIO chip driver and thereby allow
for actual performance improvements when setting multiple outputs
simultaneously. In my case the time needed to configure an FPGA goes down from
48 s to 20 s.
Change log:
v6: - rebase on current linux-gpio devel branch
v5: - no change
v4: - change interface of the set_multiple driver function to use
unsigned long as type for the bit fields
- use generic bitops (which also use unsigned long for bit fields)
v3: - change commit message
v2: - add this patch (v1 included only changes to gpiolib)
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer
interface which allow setting multiple outputs with just one function call.
Also add an optional set_multiple function to the driver interface. Without an
implementation of that function in the chip driver outputs are set
sequentially.
Implementing the set_multiple function in a chip driver allows for:
- Improved performance for certain use cases. The original motivation for this
was the task of configuring an FPGA. In that specific case, where 9 GPIO
lines have to be set many times, configuration time goes down from 48 s to
20 s when using the new function.
- Simultaneous glitch-free setting of multiple pins on any kind of parallel
bus attached to GPIOs provided they all reside on the same chip and bank.
Limitations:
Performance is only improved for normal high-low outputs. Open drain and
open source outputs are always set separately from each other. Those kinds
of outputs could probably be accelerated in a similar way if we could
forgo the error checking when setting GPIO directions.
Change log:
v6: - rebase on current linux-gpio devel branch
v5: - check can_sleep property per chip
- remove superfluous checks
- supplement documentation
v4: - add gpiod_set_array function for setting logical values
- change interface of the set_multiple driver function to use
unsigned long as type for the bit fields
- use generic bitops (which also use unsigned long for bit fields)
- do not use ARCH_NR_GPIOS any more
v3: - add documentation
- change commit message
v2: - use descriptor interface
- allow arbitrary groups of GPIOs spanning multiple chips
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
irq_of_parse_and_map() returns 0 on error, so testing for negative
result never works.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The TC3589x driver is now a device tree-only driver, so we want
only dynamic IRQs and GPIO numbers from the tc3589x, no static
assignments.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds GPIO and IRQ support for the Diolan DLN-2 GPIO module.
Information about the USB protocol interface can be found in the
Programmer's Reference Manual [1], see section 2.9 for the GPIO
module commands and responses.
[1] https://www.diolan.com/downloads/dln-api-manual.pdf
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The size_prop argument of the recently added function
acpi_dev_get_property_reference() is not used by the only current
caller of that function and is very unlikely to be used at any time
going forward.
Namely, for a property whose value is a list of items each containing
a references to a device object possibly accompanied by some integers,
the number of items in the list can always be computed as the number
of elements of type ACPI_TYPE_LOCAL_REFERENCE in the property package.
Thus it should never be necessary to provide an additional "cells"
property with a value equal to the number of items in that list. It
also should never be necessary to provide a "cells" property specifying
how many integers are supposed to be following each reference.
For this reason, drop the size_prop argument from
acpi_dev_get_property_reference() and update its caller accordingly.
Link: http://marc.info/?l=linux-kernel&m=141511255610556&w=2
Suggested-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Provide a way for device drivers using GPIOs described by ACPI
GpioIo resources in _CRS to tell the GPIO subsystem what names
(connection IDs) to associate with specific GPIO pins defined
in there.
To do that, a driver needs to define a mapping table as a
NULL-terminated array of struct acpi_gpio_mapping objects
that each contain a name, a pointer to an array of line data
(struct acpi_gpio_params) objects and the size of that array.
Each struct acpi_gpio_params object consists of three fields,
crs_entry_index, line_index, active_low, representing the index of
the target GpioIo()/GpioInt() resource in _CRS starting from zero,
the index of the target line in that resource starting from zero,
and the active-low flag for that line, respectively.
Next, the mapping table needs to be passed as the second
argument to acpi_dev_add_driver_gpios() that will register it with
the ACPI device object pointed to by its first argument. That
should be done in the driver's .probe() routine.
On removal, the driver should unregister its GPIO mapping table
by calling acpi_dev_remove_driver_gpios() on the ACPI device
object where that table was previously registered.
Included are fixes from Mika Westerberg.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some drivers need to deal with only firmware representation of its
GPIOs. An example would be a GPIO button array driver where each button
is described as a separate firmware node in device tree. Typically these
child nodes do not have physical representation in the Linux device
model.
In order to help device drivers to handle such firmware child nodes we
add dev[m]_get_named_gpiod_from_child() that takes a child firmware
node pointer as its second argument (the first one is the parent device
itself), finds the GPIO using whatever is the underlying firmware
method, and requests the GPIO properly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is actually a single device with two sets of identical registers,
which just happen to start from a different offset. Instead of having
separate GPIO chips created we consolidate them to be single GPIO chip.
In addition having a single GPIO chip allows us to handle ACPI GPIO
translation in the core in a more generic way, since the two GPIO chips
share the same parent ACPI device.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With release of ACPI 5.1 and _DSD method we can finally name GPIOs (and
other things as well) returned by _CRS. Previously we were only able to
use integer index to find the corresponding GPIO, which is pretty error
prone if the order changes.
With _DSD we can now query GPIOs using name instead of an integer index,
like the below example shows:
// Bluetooth device with reset and shutdown GPIOs
Device (BTH)
{
Name (_HID, ...)
Name (_CRS, ResourceTemplate ()
{
GpioIo (Exclusive, PullUp, 0, 0, IoRestrictionInputOnly,
"\\_SB.GPO0", 0, ResourceConsumer) {15}
GpioIo (Exclusive, PullUp, 0, 0, IoRestrictionInputOnly,
"\\_SB.GPO0", 0, ResourceConsumer) {27, 31}
})
Name (_DSD, Package ()
{
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package () {"reset-gpio", Package() {^BTH, 1, 1, 0 }},
Package () {"shutdown-gpio", Package() {^BTH, 0, 0, 0 }},
}
})
}
The format of the supported GPIO property is:
Package () { "name", Package () { ref, index, pin, active_low }}
ref - The device that has _CRS containing GpioIo()/GpioInt() resources,
typically this is the device itself (BTH in our case).
index - Index of the GpioIo()/GpioInt() resource in _CRS starting from zero.
pin - Pin in the GpioIo()/GpioInt() resource. Typically this is zero.
active_low - If 1 the GPIO is marked as active_low.
Since ACPI GpioIo() resource does not have field saying whether it is
active low or high, the "active_low" argument can be used here. Setting
it to 1 marks the GPIO as active low.
In our Bluetooth example the "reset-gpio" refers to the second GpioIo()
resource, second pin in that resource with the GPIO number of 31.
This patch implements necessary support to gpiolib for extracting GPIOs
using _DSD device properties.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The GPIO resources (GpioIo/GpioInt) used in ACPI contain a GPIO number
which is relative to the hardware GPIO controller. Typically this number
can be translated directly to Linux GPIO number because the mapping is
pretty much 1:1.
However, when the GPIO driver is using pins exported by a pin controller
driver via set of GPIO ranges, the mapping might not be 1:1 anymore and
direct translation does not work.
In such cases we need to translate the ACPI GPIO number to be suitable for
the GPIO controller driver in question by checking all the pin controller
GPIO ranges under the given device and using those to get the proper GPIO
number.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit adds the implementation of ->suspend() and ->resume()
platform_driver hooks in order to save and restore the state of the
GPIO configuration. In order to achieve that, additional fields are
added to the mvebu_gpio_chip structure.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
irq_set_irq_wake() treats its second argument as a boolean. It is much
easier to read code when constant booleans are either 0 or 1!
This particular line of code distracted me somewhat when I was doing a bit of
work in a code browser since it (spuriously) got me worried that I had
misunderstood how irq_set_irq_wake() worked.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
irq_set_irq_wake() treats its second argument as a boolean. It is much
easier to read code when constant booleans are either 0 or 1!
This particular line of code distracted me somewhat when I was doing a bit of
work in a code browser since it (spuriously) got me worried that I had
misunderstood how irq_set_irq_wake() worked.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
[jkosina@suse.cz: alter subject to be more descriptive]
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch fix company name's spelling typo in module descriptions
and a Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Chris Snook <chris.snook@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This function actually operates on a gpio_chip, so its prefix should
reflect that fact for consistency with other functions defined in
gpio/driver.h.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Whereas the DWAPB driver does not really depend on the ARM
architecture, it uses [readl|writel]_relaxed() not found on
arch such as Blackfin, so restrict this to ARM until there is
another architecture that can make use of it.
It is also using the of_node of the gpiochip, so fix this
too by requiring OF_GPIO.
All error/warnings:
make.cross ARCH=blackfin
drivers/gpio/gpio-dwapb.c: In function 'dwapb_irq_handler':
drivers/gpio/gpio-dwapb.c:91:2: error: implicit declaration of function 'readl_relaxed' [-Werror=implicit-function-declaration]
drivers/gpio/gpio-dwapb.c: In function 'dwapb_configure_irqs':
drivers/gpio/gpio-dwapb.c:212:32: error: 'struct gpio_chip' has no member named 'of_node'
drivers/gpio/gpio-dwapb.c:221:16: error: 'struct gpio_chip' has no member named 'of_node'
drivers/gpio/gpio-dwapb.c: In function 'dwapb_gpio_add_port':
drivers/gpio/gpio-dwapb.c:331:14: error: 'struct gpio_chip' has no member named 'of_node'
cc1: some warnings being treated as errors
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Alan Tull <atull@altera.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a gpiolib and IRQ chip driver for Vybrid ARM SoC using the
Vybrid's GPIO and PORT module. The driver is instanced once per
each GPIO/PORT module pair and handles 32 GPIO's.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change switches to devm_request_region to request region
and hence simplifies the module unload and does away with
release_region in remove function.
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This
was done to avoid having a custom <asm/gpio.h> header for
the x86 architecture - GPIO is custom and complicated
enough as it is already! We want to move to a radix to
store the descriptors going forward, and finally get rid
of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated
by Abdoulaye Berthe. It is not accepted by the system that
the removal of a GPIO chip fails during e.g. reboot or
shutdown, and therefore the return value has now painfully
been refactored away. For special cases like GPIO expanders
on a hot-pluggable bus like USB, we may later add some
gpiochip_try_remove() call, but for the cases we have now,
return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI
GPIO library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle
also threaded, nested interrupts and set up the parent IRQ
correctly. Switch STMPE and TC3589x drivers to use this
registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so
that also GPIO expanders that block but are still not
using threaded IRQ handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the
"DSP GPIO" found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated
from and MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08,
DWAPB, OMAP, Xilinx and Crystalcove drivers.
- Various minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8InA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the bulk of GPIO changes for the v3.18 development cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This was done
to avoid having a custom <asm/gpio.h> header for the x86
architecture - GPIO is custom and complicated enough as it is
already! We want to move to a radix to store the descriptors going
forward, and finally get rid of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated by
Abdoulaye Berthe. It is not accepted by the system that the
removal of a GPIO chip fails during eg reboot or shutdown, and
therefore the return value has now painfully been refactored away.
For special cases like GPIO expanders on a hot-pluggable bus like
USB, we may later add some gpiochip_try_remove() call, but for the
cases we have now, return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI GPIO
library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle also
threaded, nested interrupts and set up the parent IRQ correctly.
Switch STMPE and TC3589x drivers to use this registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so that also
GPIO expanders that block but are still not using threaded IRQ
handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the "DSP GPIO"
found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated from and
MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
Xilinx and Crystalcove drivers.
- Various minor fixes"
* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
gpio: pch: Build context save/restore only for PM
pinctrl: abx500: get rid of unused variable
gpio: ks8695: fix 'else should follow close brace '}''
gpio: stmpe: add verbose debug code
gpio: stmpe: fix up interrupt enable logic
gpio: staticize xway_stp_init()
gpio: handle also nested irqchips in the chained handler set-up
gpio: set parent irq on chained handlers
gpiolib: irqchip: use irq_find_mapping while removing irqchip
gpio: crystalcove: support virtual GPIO
pinctrl: bcm281xx: make Kconfig dependency more strict
gpio: kona: enable only on BCM_MOBILE or for compile testing
gpio, bcm-kona, LLVMLinux: Remove use of __initconst
gpio: Fix ngpio in gpio-xilinx driver
gpio: dwapb: fix pointer to integer cast
gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
gpio: xgene: Fix missing spin_lock_init()
gpio: ks8695: fix switch case indentation
gpiolib: add irq_not_threaded flag to gpio_chip
...
The pch_gpio_save_reg_conf() and pch_gpio_restore_reg_conf() functions
are only used in pch_gpio_suspend() and pch_gpio_resume(), respectively.
Since the latter are only built if PM is enabled, make the former build
under the same conditions.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To troubleshoot the STMPE GPIO driver, some more detailed
debug information giving the exact info on how each pin is
used will be helpful.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The STMPE driver assumes that the passed in IRQ type is
for rising or falling IRQs, not both, even though the
hardware actually supports this perfectly well. Likewise
the check for level IRQs is done against just high or low
level types, not for the case where it is combined with
other IRQs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To unify how we connect cascaded IRQ chips to parent IRQs, if
NULL us passed as handler to the gpiochip_set_chained_irqchip()
function, assume the chips is nested rather than chained, and
we still get the parent set up correctly by way of this function
call.
Alter the drivers for tc3589x and stmpe to use this to set up
their chained handlers as a demonstration of the usage.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the IRQ from the parent is nested the IRQ may need to be
resent under certain conditions. Currently the chained IRQ
handler in gpiolib does not handle connecting nested IRQs
but it is conceptually correct to indicate the actual parent
IRQ.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reported-by: Lothar Waßmann <LW@karo-electronics.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no guarantee that VIRQs will be allocated sequentially
for gpio irqchip in gpiochip_irqchip_add().
Therefore, it's unsafe to dispose VIRQ in gpiochip_irqchip_remove()
basing on index relatively to stored irq_base value.
Hence, use irq_find_mapping for VIRQ finding in gpiochip_irqchip_remove()
instead of irq_base + index.
Reported-by: Wang, Yalin <Yalin.Wang@sonymobile.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Revert of a recent hibernation core commit that introduced
a NULL pointer dereference during resume for at least one user
(Rafael J Wysocki).
- Fix for the ACPI LPSS (Low-Power Subsystem) driver to disable
asynchronous PM callback execution for LPSS devices during system
suspend/resume (introduced in 3.16) which turns out to break
ordering expectations on some systems. From Fu Zhonghui.
- cpufreq core fix related to the handling of sysfs nodes during
system suspend/resume that has been broken for intel_pstate
since 3.15 from Lan Tianyu.
- Restore the generation of "online" uevents for ACPI container
devices that was removed in 3.14, but some user space utilities
turn out to need them (Rafael J Wysocki).
- The cpufreq core fails to release a lock in an error code path
after changes made in 3.14. Fix from Prarit Bhargava.
- ACPICA and ACPI/GPIO fixes to make the handling of ACPI GPIO
operation regions (which means AML using GPIOs) work correctly
in all cases from Bob Moore and Srinivas Pandruvada.
- Fix for a wrong sign of the ACPI core's create_modalias() return
value in case of an error from Mika Westerberg.
- ACPI backlight blacklist entry for ThinkPad X201s from Aaron Lu.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=SzQq
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are regression fixes (ACPI hotplug, cpufreq, hibernation, ACPI
LPSS driver), fixes for stuff that never worked correctly (ACPI GPIO
support in some cases and a wrong sign of an error code in the ACPI
core in one place), and one blacklist item for ACPI backlight
handling.
Specifics:
- Revert of a recent hibernation core commit that introduced a NULL
pointer dereference during resume for at least one user (Rafael J
Wysocki).
- Fix for the ACPI LPSS (Low-Power Subsystem) driver to disable
asynchronous PM callback execution for LPSS devices during system
suspend/resume (introduced in 3.16) which turns out to break
ordering expectations on some systems. From Fu Zhonghui.
- cpufreq core fix related to the handling of sysfs nodes during
system suspend/resume that has been broken for intel_pstate since
3.15 from Lan Tianyu.
- Restore the generation of "online" uevents for ACPI container
devices that was removed in 3.14, but some user space utilities
turn out to need them (Rafael J Wysocki).
- The cpufreq core fails to release a lock in an error code path
after changes made in 3.14. Fix from Prarit Bhargava.
- ACPICA and ACPI/GPIO fixes to make the handling of ACPI GPIO
operation regions (which means AML using GPIOs) work correctly in
all cases from Bob Moore and Srinivas Pandruvada.
- Fix for a wrong sign of the ACPI core's create_modalias() return
value in case of an error from Mika Westerberg.
- ACPI backlight blacklist entry for ThinkPad X201s from Aaron Lu"
* tag 'pm+acpi-3.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "PM / Hibernate: Iterate over set bits instead of PFNs in swsusp_free()"
gpio / ACPI: Use pin index and bit length
ACPICA: Update to GPIO region handler interface.
ACPI / platform / LPSS: disable async suspend/resume of LPSS devices
cpufreq: release policy->rwsem on error
cpufreq: fix cpufreq suspend/resume for intel_pstate
ACPI / scan: Correct error return value of create_modalias()
ACPI / video: disable native backlight for ThinkPad X201s
ACPI / hotplug: Generate online uevents for ACPI containers
The virtual GPIO introduced in ACPI table of Baytrail-T based system is
used to solve a problem under Windows. We do not have such problems
under Linux so we do not actually need them. But we have to tell GPIO
library that the Crystal Cove GPIO chip has this many GPIO pins or the
common GPIO handler will refuse any access to those high number GPIO
pins, which will resulted in a failure evaluation of every ACPI control
method that is used to turn on/off power resource and/or report sensor
temperatures.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[changed vgpio number from 0x5e to 94]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change makes it easier to configure a kernel for a real machine by
not showing the option to enable it at all if COMPILE_TEST is off.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix code when the operation region callback is for an gpio, which
is not at index 0 and for partial pins in a GPIO definition.
For example:
Name (GMOD, ResourceTemplate ()
{
//3 Outputs that define the Power mode of the device
GpioIo (Exclusive, PullDown, , , , "\\_SB.GPI2") {10, 11, 12}
})
}
If opregion callback calls is for:
- Set pin 10, then address = 0 and bit length = 1
- Set pin 11, then address = 1 and bit length = 1
- Set for both pin 11 and pin 12, then address = 1, bit length = 2
This change requires updated ACPICA gpio operation handler code to
send the pin index and bit length.
Fixes: 473ed7be0d (gpio / ACPI: Add support for ACPI GPIO operation regions)
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+: 75ec6e55f1 ACPICA: Update to GPIO region handler interface.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The __initconst is in the wrong place, and when moved to the correct place
it uncovers an error where the variable is used by non-init data structures.
Instead merely make them const and put the const in the right spot.
Signed-off-by: Behan Webster <behanw@converseincode.com>
Reviewed-by: Mark Charlebois <charlebm@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If one adds gpio-controller; to the chip in the devicetree, then
initialization fails with 'gpiochip_find_base: cannot find free range',
because ngpio is 0. This patch fixes the bug.
This version includes the suggestions from Linus Walleij.
Tested on ml507 board.
Signed-off-by: Gernot Vormayr <gvormayr@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The statements BUG_ON(ctx == 0) was implicitly casting a pointer
to an integer for comparison. Do this with a bool test instead
to get away from sparse warnings.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver depends on OF_GPIO, so it won't be built if !CONFIG_OF.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some GPIO chips (e.g. the DLN2 USB adapter) have blocking get/set
operation but do not need a threaded irq handler.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case of error, the function devm_ioremap_nocache() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is possibility with misconfigured pins that interrupt occurs instantly
after setting irq_set_chained_handler() in gpiochip_set_chained_irqchip().
Now if handler gets called before irq_set_handler_data() the handler gets
NULL handler data.
Fix this by moving irq_set_handler_data() call before
irq_set_chained_handler() in gpiochip_set_chained_irqchip().
Cc: Stable <stable@vger.kernel.org> # 3.15+
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
GPIO direction flags are not getting set because
an 'if' statement is the wrong way around.
Cc: Stable <stable@vger.kernel.org> # 3.15+
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When viewing the /proc/interrupts, there is no information about which
GPIO bank a specific gpio interrupt is hooked on to. This is more than a
bit irritating as such information can esily be provided back to the
user and at times, can be crucial for debug.
So, instead of displaying something like:
31: 0 0 GPIO 0 palmas
32: 0 0 GPIO 27 mmc0
Display the following with appropriate device name:
31: 0 0 4ae10000.gpio 0 palmas
32: 0 0 4805d000.gpio 27 mmc0
This requires that we create irq_chip instance specific for each GPIO
bank which is trivial to achieve.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit d78c16ccde ("ARM: SAMSUNG: Remove remaining legacy code")
removed the Kconfig symbol S5P_GPIO_DRVSTR. It didn't remove one check
for the related macro. Remove that check and the dead code it hides.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch enables suspend and resume mode for the power management, and
it is based on Josef Ahmad's previous work.
Reviewed-by: Hock Leong Kweh <hock.leong.kweh@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Weike Chen <alvin.chen@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch enables 'debounce' for the designware GPIO, and
it is based on Josef Ahmad's previous work.
Reviewed-by: Hock Leong Kweh <hock.leong.kweh@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Weike Chen <alvin.chen@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Synopsys DesignWare APB GPIO driver only supports open firmware devices.
But, like Intel Quark X1000 SOC, which has a single PCI function exporting
a GPIO and an I2C controller, it is a Multifunction device. This patch is
to enable the current Synopsys DesignWare APB GPIO driver to support the
Multifunction device which exports the designware GPIO controller.
Reviewed-by: Hock Leong Kweh <hock.leong.kweh@intel.com>
Signed-off-by: Weike Chen <alvin.chen@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some drivers accidentally still use the return value from
gpiochip_remove(). Get rid of them so we can simplify this function
and get rid of the return value.
Cc: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
this remove all reference to gpio_remove retval in all driver
except pinctrl and gpio. the same thing is done for gpio and
pinctrl in two different patches.
Signed-off-by: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Michael Büsch <m@bues.ch>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On Keystone SOCs, ARM host can send interrupts to DSP cores using the
DSP GPIO controller IP. Each DSP GPIO controller provides 28 IRQ signals for
each DSP core. This is one of the component used by the IPC mechanism used
on Keystone SOCs.
Keystone 2 DSP GPIO controller has specific features:
- each GPIO can be configured only as output pin;
- setting GPIO value to 1 causes IRQ generation on target DSP core;
- reading pin value returns 0 - if IRQ was handled or 1 - IRQ is still
pending.
This patch updates gpio-syscon driver to be reused by Keystone 2 SoCs,
because the Keystone 2 DSP GPIO controller is controlled through Syscon
devices and, as requested by Linus Walleij, such kind of GPIO controllers
should be integrated with drivers/gpio/gpio-syscon.c driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds handling of new "gpio,syscon-dev" DT property,
which allows to specify syscon node and data/direction registers
offsets in DT.
"gpio,syscon-dev" has following format:
gpio,syscon-dev = <&syscon_dev data_reg_offset [direction_reg_offset]>;
where
- syscon_dev - phandle on syscon node
- data_reg_offset - offset of data register (in bytes)
- direction_reg_offset - offset of dirrection register (optional, in bytes)
for example:
gpio,syscon-dev = <&devctrl 0x254>;
In such way, the support of multiple Syscon GPIO devices is added.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some SoCs (like Keystone) may require to perform special
sequence of operations to assign output GPIO value, so default
implementation of .set() callback from gpio-syscon driver
can't be used.
Hence, add optional, SoC specific callback to assign output
gpio value.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Device tree is not enabled in some architecture where gpio
driver mcp23s08 is still required.
v2-changes:
- Parse device tree properties into platform data other than
individual variables.
v3-changes:
- Use of_node in gpio_chip device structure, because the
struct device * always has an of_node which is NULL when
OF is not used.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use of unmask/mask in set_wake was an incorrect implementation. The new
implementation correctly sets wakeup for the gpio chip's IRQ so the gpio chip
will not sleep while wakeup-enabled gpio are in use.
Signed-off-by: Ezra Savard <ezra.savard@xilinx.com>
Reviewed-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Added flag to the GPIO chip so that IRQ from non-wakeup GPIO will
not wake the system.
Signed-off-by: Ezra Savard <ezra.savard@xilinx.com>
Reviewed-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When looking up the IRQ the bank offset needs to be taken into account.
Otherwise interrupts for banks other than bank 0 get incorrectly reported as
interrupts for bank 0.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the ADNP GPIO driver to use the gpiolib
irqchip helpers. Also do some random refactoring to make it
look like most other GPIO drivers.
Cc: Roland Stigge <stigge@antcom.de>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These resources are managed by devres, and should not be explicitly
released.
Signed-off-by: Michael Auchter <a@phire.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current prototype of gpiochip_request_own_desc() requires to obtain
a pointer to a descriptor. This is in contradiction to all other GPIO
request schemes, and imposes an extra step of obtaining a descriptor to
drivers. Most drivers actually cannot even perform that step since the
function that does it (gpichip_get_desc()) is gpiolib-private.
Change gpiochip_request_own_desc() to return a descriptor from a
(chip, hwnum) tuple and update users of this function (currently
gpiolib-acpi only).
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO descriptors are changing from unique and permanent tokens to
allocated resources. Therefore gpiochip_get_desc() cannot be used as a
way to obtain a global GPIO descriptor anymore.
This patch updates the gpiolib ACPI support code to keep and use the
descriptor returned by a centralized call to gpiochip_get_desc().
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
zynq_gpio_irqhandler() uses up to 7 tabs of indention in some parts. Refactor
things to use a helper function for the inner loop to reduce the indention to a
sane level.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drop deprecated DT bindings and use automaticly assigned gpio and irq
bases.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It appears that input sensing bit might be reset during
suspend/resume. Set input sensing again for all requested gpios
in resume
Tested-by: Jerome Blin <jerome.blin@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Of_node_put supports NULL as its argument, so the initial test is not
necessary.
Suggested by Uwe Kleine-König.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
-if (e)
of_node_put(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Zynq GPIO interrupt handling code as two main issues:
1) It does not support IRQF_ONESHOT interrupt since it uses handle_simple_irq()
for the interrupt handler. handle_simple_irq() does not do masking and unmasking
of the IRQ that is required for this chip to be able to support IRQF_ONESHOT
IRQs, causing the CPU to lock up in a interrupt storm if such a interrupt is
requested.
2) Interrupts are acked after the primary interrupt handlers for all asserted
interrupts in a bank have been called. For edge triggered interrupt this is to
late and may cause a interrupt to be missed. For level triggered oneshot
interrupts this is to early and causes the interrupt handler to run twice per
interrupt.
This patch addresses the issue by updating the driver to use the correct IRQ
chip handler functions that are appropriate for this kind of IRQ controller.
The following diagram gives an overview of how the interrupt detection circuit
works, it is not necessarily a accurate depiction of the real hardware though.
INT_POL/INT_ON_ANY
|
| +---+ INT_STATUS
`-| | |
| E |-. |
,---| | \ |\ +----+ | +---+
| +---+ `----| | ,-------|S | ,*--| |
GPIO_IN -* | |- | Q|- | & |-- IRQ_OUT
| +---+ ,-----| | ,-|R | ,o| |
`---| | / |/ | +----+ | +---+
| = |- | | |
,-| | INT_TYPE ACK INT_MASK
| +---+
|
INT_POL
GPIO_IN is the raw signal level connected to the hardware pin. This signal is
routed to a edge detector and to a level detector. The edge detector can be
configured to either detect a rising or falling edge or both edges. The level
detector can detect either a level high or level low event. Depending on the
setting of the INT_TYPE register either the edge or level event will be
propagated to the INT_STATUS register. As long as a interrupt condition is
detected the INT_STATUS register will be set to 1. It can be cleared to 0 if
(and only if) the interrupt condition is no longer detected and software
acknowledges the interrupt by writing a 1 to the address of the INT_STATUS
register. There is also the INT_MASK register which can be used to disable the
propagation of the INT_STATUS signal to the upstream IRQ controller. What is
important to note is that the interrupt detection logic itself can not be
disabled, only the propagation of the INT_STATUS register can be delayed. This
means that for level type interrupts the interrupt must only be acknowledged
after the interrupt source has been cleared otherwise it will stay asserted and
the interrupt handler will be run a second time. For IRQF_ONESHOT interrupts
this means that the IRQ must only be acknowledged after the threaded interrupt
has finished running. If a second interrupt comes in between handling the first
interrupt and acknowledging it the external interrupt will be asserted, which
means trying to acknowledge the first interrupt will not clear the INT_STATUS
register and the interrupt handler will be run a second time when the IRQ is
unmasked, so no interrupts will be lost. The handle_fasteoi_irq() handler in
combination with the IRQCHIP_EOI_THREADED | IRQCHIP_EOI_IF_HANDLED flags will
have the desired behavior. For edge triggered interrupts a slightly different
strategy is necessary. For edge triggered interrupts the interrupt condition is
only true when the edge itself is detected, this means this is the only time the
INT_STATUS register is set, acknowledging the interrupt any time after that will
clear the INT_STATUS register until the next interrupt happens. This means in
order to not loose any interrupts the interrupt needs to be acknowledged before
running the interrupt handler. If a second interrupt occurs after the first
interrupt handler has finished but before the interrupt is unmasked the
INT_STATUS register will be re-asserted and the interrupt handler runs a second
time once the interrupt is unmasked. This means with this flow handling strategy
no interrupts are lost for edge triggered interrupts. The handle_level_irq()
handler will have the desired behavior. (Note: The handle_edge_irq() only needs
to be used for edge triggered interrupts where the controller stops detecting
the interrupt event when the interrupt is masked, for this controller the
detection logic still works, while only the propagation is delayed when the
interrupt is masked.)
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Correct typo in the name of the type given to sizeof. Because it is the
size of a pointer that is wanted, the typo has no impact on compilation or
execution.
This problem was found using Coccinelle (http://coccinelle.lip6.fr/). The
semantic patch used can be found in message 0 of this patch series.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle, and this time we got a lot of action going on and
it will continue:
- The core GPIO library implementation has been split up in
three different files:
- gpiolib.c for the latest and greatest and shiny GPIO
library code using GPIO descriptors only
- gpiolib-legacy.c for the old integer number space API
that we are phasing out gradually
- gpiolib-sysfs.c for the sysfs interface that we are
not entirely happy with, but has to live on for
ABI compatibility
- Add a flags argument to *gpiod_get* functions, with some
backward-compatibility macros to ease transitions. We
should have had the flags there from the beginning it
seems, now we need to clean up the mess. There is a plan
on how to move forward here devised by Alexandre Courbot
and Mark Brown.
- Split off a special <linux/gpio/machine.h> header for the
board gpio table registration, as per example from the
regulator subsystem.
- Start to kill off the return value from gpiochip_remove()
by removing the __must_check attribute and removing all
checks inside the drivers/gpio directory. The rationale
is: well what were we supposed to do if there is an error
code? Not much: print an error message. And gpiolib already
does that. So make this function return void eventually.
- Some cleanups of hairy gpiolib code, make some functions
not to be used outside the library private and make sure
they are not exported, remove gpiod_lock/unlock_as_irq()
as the existing function is for driver-internal use and
fine as it is, delete gpio_ensure_requested() as it is
not meaningful anymore.
- Support the GPIOF_ACTIVE_LOW flag from gpio_request_one()
function calls, which is logical since this is already
supported when referencing GPIOs from e.g. device trees.
- Switch STMPE, intel-mid, lynxpoint and ACPI (!) to use
the gpiolib irqchip helpers cutting down on GPIO irqchip
boilerplate a bit more.
- New driver for the Zynq GPIO block.
- The usual incremental improvements around a bunch of
drivers.
- Janitorial syntactic and semantic cleanups by Jingoo Han,
and Rickard Strandqvist especially.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=e+d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO update from Linus Walleij:
"This is the bulk of GPIO changes for the v3.17 development cycle, and
this time we got a lot of action going on and it will continue:
- The core GPIO library implementation has been split up in three
different files:
- gpiolib.c for the latest and greatest and shiny GPIO library code
using GPIO descriptors only
- gpiolib-legacy.c for the old integer number space API that we are
phasing out gradually
- gpiolib-sysfs.c for the sysfs interface that we are not entirely
happy with, but has to live on for ABI compatibility
- Add a flags argument to *gpiod_get* functions, with some
backward-compatibility macros to ease transitions. We should have
had the flags there from the beginning it seems, now we need to
clean up the mess. There is a plan on how to move forward here
devised by Alexandre Courbot and Mark Brown
- Split off a special <linux/gpio/machine.h> header for the board
gpio table registration, as per example from the regulator
subsystem
- Start to kill off the return value from gpiochip_remove() by
removing the __must_check attribute and removing all checks inside
the drivers/gpio directory. The rationale is: well what were we
supposed to do if there is an error code? Not much: print an error
message. And gpiolib already does that. So make this function
return void eventually
- Some cleanups of hairy gpiolib code, make some functions not to be
used outside the library private and make sure they are not
exported, remove gpiod_lock/unlock_as_irq() as the existing
function is for driver-internal use and fine as it is, delete
gpio_ensure_requested() as it is not meaningful anymore
- Support the GPIOF_ACTIVE_LOW flag from gpio_request_one() function
calls, which is logical since this is already supported when
referencing GPIOs from e.g. device trees
- Switch STMPE, intel-mid, lynxpoint and ACPI (!) to use the gpiolib
irqchip helpers cutting down on GPIO irqchip boilerplate a bit more
- New driver for the Zynq GPIO block
- The usual incremental improvements around a bunch of drivers
- Janitorial syntactic and semantic cleanups by Jingoo Han, and
Rickard Strandqvist especially"
* tag 'gpio-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (37 commits)
MAINTAINERS: update GPIO include files
gpio: add missing includes in machine.h
gpio: add flags argument to gpiod_get*() functions
MAINTAINERS: Update Samsung pin control entry
gpio / ACPI: Move event handling registration to gpiolib irqchip helpers
gpio: lynxpoint: Convert to use gpiolib irqchip
gpio: split gpiod board registration into machine header
gpio: remove gpio_ensure_requested()
gpio: remove useless check in gpiolib_sysfs_init()
gpiolib: Export gpiochip_request_own_desc and gpiochip_free_own_desc
gpio: move gpio_ensure_requested() into legacy C file
gpio: remove gpiod_lock/unlock_as_irq()
gpio: make gpiochip_get_desc() gpiolib-private
gpio: simplify gpiochip_export()
gpio: remove export of private of_get_named_gpio_flags()
gpio: Add support for GPIOF_ACTIVE_LOW to gpio_request_one functions
gpio: zynq: Clear pending interrupt when enabling a IRQ
gpio: drop retval check enforcing from gpiochip_remove()
gpio: remove all usage of gpio_remove retval in driver/gpio
devicetree: Add Zynq GPIO devicetree bindings documentation
...
This is the bulk of new SoC enablement and other platform changes for 3.17:
* Samsung S5PV210 has been converted to DT and multiplatform
* Clock drivers and bindings for some of the lower-end i.MX 1/2 platforms
* Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood.
* Hwmod data for TI AM43xx and DRA7 platforms.
* More additions of Renesas shmobile platform support
* Removal of plat-samsung contents that can be removed with S5PV210 being
multiplatform/DT-enabled and the other two old platforms being removed.
New platforms (most with only basic support right now):
* Hisilicon X5HD2 settop box chipset is introduced
* Mediatek MT6589 (mobile chipset) is introduced
* Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=5TJ6
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This is the bulk of new SoC enablement and other platform changes for
3.17:
- Samsung S5PV210 has been converted to DT and multiplatform
- Clock drivers and bindings for some of the lower-end i.MX 1/2
platforms
- Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood
- Hwmod data for TI AM43xx and DRA7 platforms
- More additions of Renesas shmobile platform support
- Removal of plat-samsung contents that can be removed with S5PV210
being multiplatform/DT-enabled and the other two old platforms
being removed
New platforms (most with only basic support right now):
- Hisilicon X5HD2 settop box chipset is introduced
- Mediatek MT6589 (mobile chipset) is introduced
- Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code"
* tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (240 commits)
ARM: hisi: remove smp from machine descriptor
power: reset: move hisilicon reboot code
ARM: dts: Add hix5hd2-dkb dts file.
ARM: debug: Rename Hi3716 to HIX5HD2
ARM: hisi: enable hix5hd2 SoC
ARM: hisi: add ARCH_HISI
MAINTAINERS: add entry for Broadcom ARM STB architecture
ARM: brcmstb: select GISB arbiter and interrupt drivers
ARM: brcmstb: add infrastructure for ARM-based Broadcom STB SoCs
ARM: configs: enable SMP in bcm_defconfig
ARM: add SMP support for Broadcom mobile SoCs
Documentation: arm: misc updates to Marvell EBU SoC status
Documentation: arm: add URLs to public datasheets for the Marvell Armada XP SoC
ARM: mvebu: fix build without platforms selected
ARM: mvebu: add cpuidle support for Armada 38x
ARM: mvebu: add cpuidle support for Armada 370
cpuidle: mvebu: add Armada 38x support
cpuidle: mvebu: add Armada 370 support
cpuidle: mvebu: rename the driver from armada-370-xp to mvebu-v7
ARM: mvebu: export the SCU address
...
This merge window brings a good size of cleanups on various
platforms. Among the bigger ones:
* Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
lacked active support for quite a while, and after asking around nobody
showed interest in keeping them around. If needed, they could be
resurrected in the future but it's more likely that we would prefer
reintroduction of them as DT and multiplatform-enabled platforms
instead.
* OMAP4 controller code register define diet. They defined a lot of registers
that were never actually used, etc.
* Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
to drivers/soc so it can be shared with 64-bit code. This also converts them
over to traditional driver models where possible.
* Removal of legacy gpio-samsung driver, since the last users have been
removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some misc
cleanups, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=gbcE
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
- Checkpatch fixes throughout the subsystem
- Use Regmap to handle IRQs in max77686, extcon-max77693 and mc13xxx-core
- Use DMA in rtsx_pcr
- Restrict building on unsupported architectures on timberdale, cs5535
- SPI hardening in cros_ec_spi
- More robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- Reorder PM runtime and regulator handing during shutdown in arizona
- Enable wakeup in cros_ec_spi
- Unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- Add regulator handing into suspend() in sec-core
- Remove pointless wrapper functions in extcon-max77693 and i2c-cros-ec-tunnel
- Use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- Device Tree documentation updates throughout
- Provide power management support in max77686
- Few OF clean-ups in max77686
- Use manged resources in tps6105x
== New drivers/supported devices ==
- Add support for s2mpu02 to sec-core
- Add support for Allwinner A32 to sun6i-prcm
- Add support for Maxim 77802 in max77686
- Add support for DA9063 AD in da9063
- Add new driver for Intel PMICs (generic) and specifically Crystal Cove
== (Re-)moved drivers ==
- Move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2cNI
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD update from Lee Jones:
"Changes to existing drivers:
- checkpatch fixes throughout the subsystem
- use Regmap to handle IRQs in max77686, extcon-max77693 and
mc13xxx-core
- use DMA in rtsx_pcr
- restrict building on unsupported architectures on timberdale,
cs5535
- SPI hardening in cros_ec_spi
- more robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- reorder PM runtime and regulator handing during shutdown in arizona
- enable wakeup in cros_ec_spi
- unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- add regulator handing into suspend() in sec-core
- remove pointless wrapper functions in extcon-max77693 and
i2c-cros-ec-tunnel
- use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- devicetree documentation updates throughout
- provide power management support in max77686
- few OF clean-ups in max77686
- use manged resources in tps6105x
New drivers/supported devices:
- add support for s2mpu02 to sec-core
- add support for Allwinner A32 to sun6i-prcm
- add support for Maxim 77802 in max77686
- add support for DA9063 AD in da9063
- new driver for Intel PMICs (generic) and specifically Crystal Cove
(Re-)moved drivers ==
- move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb"
* tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (101 commits)
MAINTAINERS: Update MFD repo location
mfd: omap-usb-host: Fix improper mask use.
mfd: arizona: Only free the CTRLIF_ERR IRQ if we requested it
mfd: arizona: Add missing handling for ISRC3 under/overclocked
mfd: wm5110: Add new interrupt register definitions
mfd: arizona: Rename thermal shutdown interrupt
mfd: wm5110: Add in the output done interrupts
mfd: wm5110: Remove non-existant interrupts
mfd: tps65912-spi: Remove unused variable
mfd: htc-i2cpld: Remove unused code
mfd: da9063: Add support for AD silicon variant
mfd: arizona: Map MICVDD from extcon device to the Arizona core
mfd: arizona: Add MICVDD to mapped regulators for wm8997
mfd: max77686: Ensure device type IDs are architecture agnostic
mfd: max77686: Add Maxim 77802 PMIC support
mfd: tps6105x: Use managed resources when allocating memory
mfd: wm8997-tables: Suppress 'line over 80 chars' warnings
mfd: kempld-core: Correct a variety of checkpatch warnings
mfd: ipaq-micro: Fix coding style errors/warnings reported by checkpatch
mfd: si476x-cmd: Remedy checkpatch style complains
...
The huge majority of GPIOs have their direction and initial value set
right after being obtained by one of the gpiod_get() functions. The
integer GPIO API had gpio_request_one() that took a convenience flags
parameter allowing to specify an direction and value applied to the
returned GPIO. This feature greatly simplifies client code and ensures
errors are always handled properly.
A similar feature has been requested for the gpiod API. Since setting
the direction of a GPIO is so often the very next action done after
obtaining its descriptor, we prefer to extend the existing functions
instead of introducing new functions that would raise the
number of gpiod getters to 16 (!).
The drawback of this approach is that all gpiod clients need to be
updated. To limit the pain, temporary macros are introduced that allow
gpiod_get*() to be called with or without the extra flags argument. They
will be removed once all consumer code has been updated.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since now we have irqchip helpers that the GPIO chip drivers are supposed
to use if possible, we can move the registration of ACPI events to happen
in these helpers. This seems to be more natural place and might encourage
GPIO chip driver writers to take advantage of the irqchip helpers.
We make the functions available to GPIO chip drivers via private gpiolib.h,
just in case generic irqchip helpers are not suitable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of open-coding irqchip handling in the driver we can take advantage
of the new irqchip helpers provided by the gpiolib core.
While doing this we also make sure that we call gpiochip_irqchip_add()
after the gpiochip itself is registered as required.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As per example from the regulator subsystem: put all defines and
functions related to registering board info for GPIO descriptors
into a separate <linux/gpio/machine.h> header.
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- support common clock framework for s5pv210 clock
- add generic PHY driver on s5pv210 to support it via DT
- add dt support for s5pv210-goni, smdkc110, smdkv210 and torbreck boards
- remove board files from mach-s5pv210 and unused codes
- enable multiplatform for s5pv210
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7b91
-----END PGP SIGNATURE-----
Merge tag 's5pv210-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
Merge "Samsung S5PV210 DT support for v3.17" from Kukjin Kim:
- support common clock framework for s5pv210 clock
- add generic PHY driver on s5pv210 to support it via DT
- add dt support for s5pv210-goni, smdkc110, smdkv210 and torbreck boards
- remove board files from mach-s5pv210 and unused codes
- enable multiplatform for s5pv210
* tag 's5pv210-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
clk: samsung: s5pv210: Remove legacy board support
ARM: SAMSUNG: Remove remaining legacy code
gpio: samsung: Remove legacy support of S5PV210
ARM: S5PV210: Enable multi-platform build support
cpufreq: s5pv210: Make the driver multiplatform aware
ARM: S5PV210: Register cpufreq platform device
ARM: S5PV210: move debug-macro.S into the common space
ARM: S5PV210: Untie PM support from legacy code
ARM: S5PV210: Remove support for board files
ARM: dts: Add Device tree for s5pc110/s5pv210 boards
ARM: dts: Add Device tree for s5pv210 SoC
ARM: S5PV210: Add board file for boot using Device Tree
phy: Add support for S5PV210 to the Exynos USB 2.0 PHY driver
clk: samsung: Add S5PV210 Audio Subsystem clock driver
ARM: SAMSUNG: Remove legacy clock code
serial: samsung: Remove support for legacy clock code
cpufreq: s3c24xx: Remove some dead code
ARM: S5PV210: Migrate clock handling to Common Clock Framework
clk: samsung: Add clock driver for S5PV210 and compatible SoCs
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTzJFGAAoJEHm+PkMAQRiGNzQH/087gQch5K+A2HKvPzjUXq57
G82DJHLONMMq8+NY3Vqhp8g2V8zRbXGJEvMJMsyuscO37Vo7ADcrYo8lqY9w5bIl
h+Zarhkqz0rqRs2SfMMIVzdd2W7MzL+lqj3GplGPxHztw0+qk7PRKILx6eRppGaH
JaD4NfkD5+1vfve/2d1ze9D5pCiw6PFNzjesKZxScQhNhIyLdRamfSTY4r9XeURo
CxpwjphEYfvAcgc39mwzEHPHyKSqULu0By6R8FXQpJ9QjVtzcGEiF+cPqGncpZOR
5ZSyU5e1CpBl9w8o6Lm9ewXmaCSnBU/VFrOwWvZrXfokZedXBOz7KdShU93XFjU=
=0VJM
-----END PGP SIGNATURE-----
Merge branches 'samsung/cleanup' and 'samsung/s5p-cleanup-v2', tag 'v3.16-rc6' into next/soc
The following samsung branches are based on these cleanups,
which are already in mainline before this branch gets pulled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
gpio_ensure_requested() has been introduced in Feb. 2008 by commit
d2876d08d8 to force users of the GPIO API to explicitly request GPIOs
before using them.
Hopefully by now all GPIOs are correctly requested and this extra check
can be omitted ; in any case the GPIO maintainers won't feel bad if
machines start failing after 6 years of warnings.
This patch removes that function from the dark ages.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
An iterator variable cannot be NULL in its loop.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Both functions were introduced to let gpio drivers request their own
gpio pins. Without exporting the functions, this can however only be
used by gpio drivers built into the kernel.
Secondary impact is that the functions can not currently be used by
platform initialization code associated with the gpio-pca953x driver.
This code permits auto-export of gpio pins through platform data, but
if this functionality is used, the module can no longer be unloaded due
to the problem solved with the introduction of gpiochip_request_own_desc
and gpiochip_free_own_desc.
Export both function so they can be used from modules and from
platform initialization code.
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- An IRQ handling fix for the STi driver, also for stable
- Another IRQ fix for the RCAR GPIO driver
- A MAINTAINERS entry
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pzyJ
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here are three pin control fixes for the v3.16 series. Sorry that
some of these arrive late, the summer heat in Sweden makes me slow.
- an IRQ handling fix for the STi driver, also for stable
- another IRQ fix for the RCAR GPIO driver
- a MAINTAINERS entry"
* tag 'pinctrl-v3.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
gpio: rcar: Add support for DT IRQ flags
MAINTAINERS: Add entry for the Renesas pin controller driver
pinctrl: st: Fix irqmux handler
gpio_ensure_requested() only makes sense when using the integer-based
GPIO API, so make sure it is called from there instead of the gpiod
API which we know cannot be called with a non-requested GPIO anyway.
The uses of gpio_ensure_requested() in the gpiod API were kind of
out-of-place anyway, so putting them in gpio-legacy.c helps clearing the
code.
Actually, considering the time this ensure_requested mechanism has been
around, maybe we should just turn this patch into "remove
gpio_ensure_requested()" if we know for sure that no user depend on it
anymore?
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio_lock/unlock_as_irq() are working with (chip, offset) arguments and
are thus not using the old integer namespace. Therefore, there is no
reason to have gpiod variants of these functions working with
descriptors, especially since the (chip, offset) tuple is more suitable
to the users of these functions (GPIO drivers, whereas GPIO descriptors
are targeted at GPIO consumers).
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As GPIO descriptors are not going to remain unique anymore, having this
function public is not safe. Restrain its use to gpiolib since we have
no user outside of it.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For some reason gpiochip_export() would invalidate all the descriptors
of a chip if exporting it to sysfs failed. This does not appear as
necessary. Remove that part of the code.
While we are at it, add a note about the non-safety of temporarily
releasing a spinlock in the middle of the loop that protects its
iterator, and explain why this is done.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_get_named_gpio_flags() has been made gpiolib-private by commit
f01d907582, but its EXPORT statement has not been removed. Fix this.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio include file and the gpio documentation declare and document
GPIOF_ACTIVE_LOW as one of the flags to be passed to gpio_request_one
and related functions. However, the flag is not evaluated or used.
This can cause problems in at least two areas: First, the same API can
be used to auto-export pins to user space. The missing support for
GPIOF_ACTIVE_LOW results in unexpected behavior for such auto-exported
pins. Second, the requested gpio pin can be convered for use by
gpiod functions with gpio_to_desc(). While gpio API functions do not
support GPIOF_ACTIVE_LOW, gpiod functions do, which again results in
unexpected behavior.
Check the flag in gpio_request_one and set the gpio internal flag
FLAG_ACTIVE_LOW if it is set to address those problems.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Zynq GPIO controller does not disable the interrupt detection when the
interrupt is masked and only disables the propagation of the interrupt. This
means when the controller detects an interrupt condition while the interrupt is
logically disabled (and masked) it will propagate the recorded interrupt event
once the interrupt is enabled. This will cause the interrupt consumer to see
spurious interrupts to prevent this first make sure that the interrupt is not
asserted and then enable it.
E.g. when a interrupt is requested with request_irq() it will be configured
according to the requested type (edge/level triggered, etc.) after that it will
be enabled. But the detection circuit might have already registered a false
interrupt before the interrupt type was correctly configured and once the
interrupt is unmasked this false interrupt will be propagated and the interrupt
handler for the just request interrupt will called.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO support of S5PV210 SoC is now fully handled by pinctrl-samsung
driver making the old code in gpio-samsung driver unused. This patch
removes it which will also let us remove more code from arch subtree.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
want to see it again.
- Remove the need for <mach/gpio.h> from S5P
- Kill CONFIG_NEED_MACH_GPIO_H
- Kill remnants of ARM_GPIOLIB_COMPLEX
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Gyiy
-----END PGP SIGNATURE-----
Merge tag 'gpio-h-purge' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio into next/cleanup
This is a purge of all things <mach/gpio.h>, now I never
want to see it again.
- Remove the need for <mach/gpio.h> from S5P
- Kill CONFIG_NEED_MACH_GPIO_H
- Kill remnants of ARM_GPIOLIB_COMPLEX
* tag 'gpio-h-purge' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
ARM: delete old reference to ARM_GPIOLIB_COMPLEX
ARM: kill CONFIG_NEED_MACH_GPIO_H
ARM: mach-s5p: get rid of all <mach/gpio.h> headers
ARM: s5p: cut the custom ARCH_NR_GPIOS definition
Signed-off-by: Olof Johansson <olof@lixom.net>
The gpio-rcar driver has no IRQ domain OF xlate function and thus
ignores IRQ flags specified in DT. Fix this by using the two-cell xlate
function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for GPIO controller used by Xilinx Zynq.
v3 changes:
- Use linux/gpio/driver.h instead of linux/gpio.h
- Make irq a local variable in probe
v2 changes:
- convert to pm_runtime_force_(suspend|resume)
- add pm_runtime_set_active in probe()
- also (un)prepare clocks when they are dis-/enabled
- add some missing calls to pm_runtime_get()
- use pm_runtime_put() instead of sync variant
- remove gpio chip in driver remove()
- remove redundant type casts
- directly use IO helpers
- use BIT macro to set/clear bits
- migrate to GPIOLIB_IRQCHIP
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Following is the debug output (only a few examples) before and after
the patch.
$ dmesg | grep of_get_named_gpiod_flags
Before:
of_get_named_gpiod_flags: can't parse gpios property
of node '/mmc@12220000[0]'
of_get_named_gpiod_flags exited with status 0
After:
of_get_named_gpiod_flags: can't parse 'wp-gpios' property
of node '/mmc@12220000[0]'
of_get_named_gpiod_flags: parsed 'gpios' property of node
'/gpio-keys/power[0]' - status (0)
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The old integer GPIO interface is, in effect, a privileged user of the
gpiod interface. Reflect this fact further by moving legacy GPIO support
into its own source file. This makes the code clearer and will allow us
to disable legacy GPIO support in the (far) future.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
sysfs support is currently entangled within the core GPIO support, while
it should relly just be a (privileged) user of the integer GPIO API.
This patch is a first step towards making the gpiolib code more readable
by splitting it into logical parts.
Move all sysfs support to their own source file, and share static
members of gpiolib that need to be in the private gpiolib.h file. In
the future we will want to put some of them back into gpiolib.c, but this
first patch let us at least identify them.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Compiling out GPIO labels results in a space gain so small that it can
hardly be justified. Labels can also be useful for printing debug
messages, so always keep them around.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO OMAP driver didn't have a consistent naming scheme for
all its functions. Some of them had an omap prefix while others
didn't. There are many advantages on having a separate namespace
for driver functions so let's add an "omap" prefix to all of them.
Signed-off-by: Javier Martinez Canillas <jmartinez@softcrates.net>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The <linux/irqchip/chained_irq.h> header is already included
when selecting GPIOLIB_IRQCHIP so there is no need to do it
in the driver. This is a left over from commit fb655f5
("gpio: omap: convert driver to use gpiolib irqchip").
Signed-off-by: Javier Martinez Canillas <jmartinez@softcrates.net>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO irqchips assign to the cascaded IRQs their own lock class
in order to avoid warnings about lockdep recursions since that
allow the lockdep core to keep track of things.
Since commit e45d1c80 ("gpio: put GPIO IRQs into their own lock class")
there is no need to do this in a driver if it's using the GPIO
irqchip helpers since gpiolib already assigns a lockdep class.
Signed-off-by: Javier Martinez Canillas <jmartinez@softcrates.net>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Removal of null pointer checks that could never happen
This was found using a static code analysis program called cppcheck
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Removal of null pointer checks that could never happen
This was found using a static code analysis program called cppcheck
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver was not checking the return value from gpiochip_add()
properly, so add a bail-out check.
Reported-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While it will be clamped to bool by gpiolib, let's make this sane
in the driver as well.
Signed-off-by: Jürg Billeter <j@bitron.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch removes gpio codes for s5p6440 and s5p6450 SoCs.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
pxa_gpio_probe() has some issues supporting the gpio0 and gpio1
interrupts under device-tree - it never actually sets up the chain
handler to get interrupts on edge detect for GPIO0 and GPIO1.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Unnecessary checking was added during the merge of the gpio branch.
This patch removes the extra unnecessary checking.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This renames all the local <mach/gpio.h> headers in the S5P platforms
to <mach/gpio-samsung.h> indicating a scope local to this platform,
and cuts the implicit inclusion of <mach/gpio.h> from <linux/gpio.h>
by removing the use of NEED_MACH_GPIO_H from all S5P variants.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
drivers/gpio/gpio-crystalcove.c: In function 'crystalcove_gpio_dbg_show':
drivers/gpio/gpio-crystalcove.c:286:3: error: implicit declaration of function 'seq_printf'
seq_printf(s, " gpio-%-2d %s %s %s %s ctlo=%2x,%s %s %s\n",
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-By: Roland Stigge <stigge@antcom.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the Intel MID GPIO driver over to using the gpiolib
irqchip helpers in the gpiolib core.
Cc: xinhui.pan <xinhuiX.pan@intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the STMPE driver to use the gpiolib irqchip
helpers.
Tested-by: Silvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Devices based on Intel SoC products such as Baytrail have a Power
Management IC. In the PMIC there are subsystems for voltage regulation,
A/D conversion, GPIO and PWMs. The PMIC in Baytrail-T platform is
called Crystal Cove.
This patch adds support for the GPIO function in Crystal Cove.
Signed-off-by: Yang, Bin <bin.yang@intel.com>
Signed-off-by: Zhu, Lejun <lejun.zhu@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit dd34c37aa3 (gpio: of: Allow -gpio suffix for property names)
added parsing for both -gpio and -gpios suffix but also changed
the handling for deferred probe unintentionally. Because of the
looping the second name will now return -ENOENT instead of
-EPROBE_DEFER. Fix the issue by breaking out of the loop if
-EPROBE_DEFER is encountered.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- We are finalizing and fixing up the gpiochip irqchip helpers
bringing a helpful irqchip implementation into the gpiolib
core and avoiding duplicate code and, more importantly,
duplicate bug fixes:
- Support for using the helpers with threaded interrupt
handlers as used on sleeping GPIO-irqchips
- Do not set up hardware triggers for edges or levels if
the default IRQ type is IRQ_TYPE_NONE - some drivers
would exploit the fact that you could get default
initialization of the IRQ type from the core at probe()
but if no default type is set up from the helper, we
should not call the driver to configure anything. Wait
until a consumer requests the interrupt instead.
- Make the irqchip helpers put the GPIO irqs into their
own lock class. The GPIO irqchips can often emit
(harmless, but annoying) lockdep warnings about recursions
when they are in fact just cascaded IRQs. By putting
them into their own lock class we help the lockdep core
to keep track of things.
- Switch the tc3589x GPIO expanders to use the irqchip
helpers
- Switch the OMAP GPIO driver to use the irqchip helpers
- Add some documentation for the irqchip helpers
- select IRQ_DOMAIN when using the helpers since some
platforms may not be using this by default and it's a
strict dependency.
- Continued GPIO descriptor refactoring:
- Remove the one instance of gpio_to_desc() from the
device tree code, making the OF GPIO code use GPIO
descriptors only.
- Introduce gpiod_get_optional() and
gpiod_get_optional_index() akin to the similar
regulator functions for cases where the use of GPIO
is optional and not strictly required.
- Make of_get_named_gpiod_flags() private - we do not
want to unnecessarily expose APIs to drivers that
make the gpiolib harder than necessary to maintain
and refactor. Privatize this function.
- Support "-gpio" suffix for the OF GPIO retrieveal path.
We used to look for "foo-gpios" or just "gpios" in device
tree nodes, but it turns out that some drivers with a
single GPIO line will just state "foo-gpio" (singularis).
Sigh. Support this with a fallback looking for it, as
this simplifies driver code and handles it in core code.
- Switch the ACPI GPIO core to fetch GPIOs with the
*_cansleep function variants as the GPIO operation
region handler can sleep, and shall be able to handle
gpiochips that sleep.
- Tons of cleanups and janitorial work from Jingoo Han,
Axel Lin, Javier Martinez Canillas and Abdoulaye Berthe.
Notably Jingoo cut off a ton of pointless OOM messages.
- Incremental development and fixes for various drivers,
nothing really special here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=M59o
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio into next
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v3.16 series.
There is a lot of action in the GPIO subsystem doing refactorings and
cleanups, almost as many deletions as insertions and minor feature
growth and no new drivers this time. Which is actually pretty nice.
Some GPIO-related stuff will come in through the pin control tree as
well.
Details:
- We are finalizing and fixing up the gpiochip irqchip helpers
bringing a helpful irqchip implementation into the gpiolib core and
avoiding duplicate code and, more importantly, duplicate bug fixes:
* Support for using the helpers with threaded interrupt handlers as
used on sleeping GPIO-irqchips
* Do not set up hardware triggers for edges or levels if the
default IRQ type is IRQ_TYPE_NONE - some drivers would exploit
the fact that you could get default initialization of the IRQ
type from the core at probe() but if no default type is set up
from the helper, we should not call the driver to configure
anything. Wait until a consumer requests the interrupt instead.
* Make the irqchip helpers put the GPIO irqs into their own lock
class. The GPIO irqchips can often emit (harmless, but annoying)
lockdep warnings about recursions when they are in fact just
cascaded IRQs. By putting them into their own lock class we help
the lockdep core to keep track of things.
* Switch the tc3589x GPIO expanders to use the irqchip helpers
* Switch the OMAP GPIO driver to use the irqchip helpers
* Add some documentation for the irqchip helpers
* select IRQ_DOMAIN when using the helpers since some platforms may
not be using this by default and it's a strict dependency.
- Continued GPIO descriptor refactoring:
* Remove the one instance of gpio_to_desc() from the device tree
code, making the OF GPIO code use GPIO descriptors only.
* Introduce gpiod_get_optional() and gpiod_get_optional_index()
akin to the similar regulator functions for cases where the use
of GPIO is optional and not strictly required.
* Make of_get_named_gpiod_flags() private - we do not want to
unnecessarily expose APIs to drivers that make the gpiolib harder
than necessary to maintain and refactor. Privatize this
function.
- Support "-gpio" suffix for the OF GPIO retrieveal path. We used to
look for "foo-gpios" or just "gpios" in device tree nodes, but it
turns out that some drivers with a single GPIO line will just state
"foo-gpio" (singularis). Sigh. Support this with a fallback
looking for it, as this simplifies driver code and handles it in
core code.
- Switch the ACPI GPIO core to fetch GPIOs with the *_cansleep
function variants as the GPIO operation region handler can sleep,
and shall be able to handle gpiochips that sleep.
- Tons of cleanups and janitorial work from Jingoo Han, Axel Lin,
Javier Martinez Canillas and Abdoulaye Berthe. Notably Jingoo cut
off a ton of pointless OOM messages.
- Incremental development and fixes for various drivers, nothing
really special here"
* tag 'gpio-v3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
gpio: select IRQ_DOMAIN for gpiolib irqchip helpers
gpio: pca953x: use gpiolib irqchip helpers
gpio: pcf857x: Add IRQF_SHARED when request irq
gpio: pcf857x: Avoid calling irq_domain_cleanup twice
gpio: mcp23s08: switch chip count to int
gpio: dwapb: use a second irq chip
gpio: ep93xx: Use devm_ioremap_resource()
gpio: mcp23s08: fixed count variable for devicetree probing
gpio: Add run-time dependencies to R-Car driver
gpio: pch: add slab include
Documentation / ACPI: Fix location of GPIO documentation
gpio / ACPI: use *_cansleep version of gpiod_get/set APIs
gpio: generic: add request function pointer
gpio-pch: Fix Kconfig dependencies
gpio: make of_get_named_gpiod_flags() private
gpio: gpioep93xx: use devm functions
gpio: janzttl: use devm function
gpio: timberdale: use devm functions
gpio: bt8xx: use devm function for memory allocation
gpio: include linux/bug.h in interface header
...
